Search Documents

By C. G. Dunn

THE present note, which was given in the form of a Research in Progress item,' traces the origin of secondary recrystallization grains produced on annealing a cold rolled bicrystal specimen. The investigation began with the realization that a recently acquired conception for the origin of secondary grains produced on annealing cold rolled single-crystal specimens might require modifications for the case of polycrystalline materials. The stated conception2,3 begins with several conditions to be met by primary recrystallization: 1—a primary re-crystallization structure to consist of many small primaries and relatively few large primaries (diam- eters two or three times the average); 2—a primary recrystallization texture to consist of one strong preferred orientation or component and one or more weak components; and 3—a primary recrystalliza-tion structure-texture combination with some of the large primaries belonging to the weak components of the texture. When these conditions occur, some of the large primaries from the weak components of the texture

Jan 1, 1955

By R. F. Mitchell, G. F. Dillon, A. F. Armington

In this paper the present methods of boron preparation are discussed with emphasis on the iodide intermediate. Several methods of boron triiodide preparation were investigated, the most satisfactory method being the preparation from the elements. A yield of 60 pct based on iodine is found for this method. Zone-refining, sublinzation, distillation, and fractional-recrystallization results are given for the boron triiodide, with distillation producing the best results. Several methods of decomposition are also discussed. The purity of the resulting iodide boron approximates the puritjl of the best available bromide boron, ELEMENTAL boron has been suggested as a possible high-temperature semiconductor by several workers,' but has never been exploited as a device material. The principal difficulty with boron is the unavailability of pure crystalline material from which accurate information on electrical properties could be obtained. Most boron crystals presently produced are very imperfect in structure and of questionable purity, particularly in relation to carbon content. Several methods of boron purification have been reported in the past few years, all of which produce material with a purity better than 99.0 pct. Most of these methods have been the subject of a recent review by Starks' and will not be elaborated upon in this report. However, of all the purification methods reported, only those using halide intermediates produce a purity approaching that usually required for electronic applications. The bromide intermediate has been most used for the preparation of high-purity boron.'y3 This material is easily prepared from the elements and can be effectively purified by distillation and decomposed by hydrogen reduction. The resulting product contains a trace of silicon, and an uncertain amount of carbon, believed to be approximately 100 ppm. It has been recently reported by Russian workers that high-purity boron can be produced using an iodide intermediate.' In the work cited, boron is reported free of spectro-scopically determined impurities, but the reported detection limits are quite high (- 100 ppm). In addition, no data is given on the carbon content of the product. In the present paper, boron triiodide was chosen as the intermediate for several reasons. First, carbon tetraiodide, which could be a major impurity, is reported to be unstable above 200" and hence could be easily separated from the boron triiodide by its decomposition, since temperatures greater than this are attained during the purification process. The low melting point (45°C) and boiling point (20B°C) and the relatively high vapor pressure of boron triiodide should allow the application of any physical purification technique to the material. The possibility of a lower decomposition temperature than that used for the bromide process is another advantage which might cut down extraneous contamination. The iodide, however, does have certain disadvantages when compared with the bromide, the production cost being the most significant. This is the result of a higher halide-to-boron weight ratio, which means more intermediate must be employed. The cost of the starting material is also greater for the iodide. This cost could be considerably reduced however, by recycling the iodine byproduct. Epitaxial growth of boron, which is probably the best method of producing junctions, should be possible with either the bromide or the iodide as the intermediate. However, this has been attempted only on a limited scale up to the present time because of the unavailability of good crystals. The authors have been relatively successful in laying down a heterotaxy of boron on silicon, however. This will be reported at a later date. Several crystalline modifications have been reported for boron, four of which are now believed to be real.' These are the a! and 0 rhombohedral and the a, and 0 tetragonal. In general, the a! rhombohedral is the low-temperature form and the B rhombohedral is the high-temperature form. The tetragonal structures are detected between 1000"

Jan 1, 1964

By J. D. Lindner, Gene E. Roark

Waterflooding operations in the Langston-Kleiner field. Young County, Tex., are described. Widespread application of formation fracturing has been practiced in both producing and injection wells. Field performance data arc cited which indicate than no detrimental effect on sweep efficiencies and that probable benefits in imectivily have resulted from the fracture treatments. I N T R O D U C I O N This paper is a report on a waterflood operation which is being carried out in the Lanpston-Kleiner field located in Young County, Tex. The oil reservoir aflected by this flood operation occurs in a Strawn sand member at an approximate depth of 3.550 ft subsurl'ace. The operators of' the project are Kleiner Estate. Turncr. Fiske. and West who are hereinafter collectively referred to as the Operators. Although the operation is unusual in several respects, the distinctive feature of this flood has been the widespread application of hydraulic formation fracturing treatments as a means to improve productivity and injectivity of the wells. It shall he the purpose of this paper to present basic information regarding the reservoir characteristics. op- craling practices, and waterflood behavior so that conclusions may be drawn concerning the effects which the fracture treatments have had on the performance of this water flood to datc. DEVELOP MENT Development of the 3,550 ft Strawn sand reservoir occurred during 1951 and 1952. The early development occurred on the Langston and Davis leases which arc in the northern region of the Operators' holdings and the wells were drilled on 20-acre proration units according to the field rules. However, studies of the economics of this program. coupled with the decision to proceed with pressure maintenance by water injection. resulted in the adoption of wider spacing in the later stages of development. This variation in spacing is apparent upon inspection of Fig. I upon which only the 3,550-ft Strawn sand producing and injection wells have been located on the Operators' properties. The development to the north of the operators leases is Ihe Garvey Strawn field and that to the south is the Taylor Strawn field. It wits determined that unitization of the leases to he involved in the waterflood program was not feasihle. Consequently. a system of offset injection wells, or lease line injection wells, was adopted from place to place as required to protect correlative rights in the program. This resulted in a dispersed array of injection and producing wells with relatively close proximity of wells along lease line areas and wider spacing toward

Jan 1, 1956

By M. J. Pearse

The processing of fine particles inevitably produces slimes. These present a dewatering problem, for which gravity thickening provides a partial or preliminary solution. The paper shows the effects of practical factors in carrying out laboratory sizing tests for thickeners. Several methods of determining thickener unit area have been compared for a lightly coagulated phosphate slurry and a highly flocculated kaolin slurry. Practical techniques of mixing and flocculant addition have significant effects on batch settling data. Pulp temperature and cylinder dimensions are very important. Errors in sizing thickeners for highly flocculated slurries by the standard methods are discussed. Such methods are suitable for less compressible slurries, however. Rules of thumb for flocculant selection are given.

Jan 1, 1980

By Frank H. Kingdon

and eventually we would have trouble. That is, these little localized overstresses may not be important if the structure is loaded a few times, but may be important if the structure is loaded many thousands of times. The existence of localized stress has been demonstrated by direct experimentation with delicate extensometers by the elaborate investigations of Coker. Localized stresses four, five, and six times those that we would get by the ordinary laws of mechanics exist in most of our structures. These stresses, ordinarily, under steady load do no damage but if they are repeated many times may start progressive failure. So far, we have seen no failure that could not be explained by localized high stress at a nick, a crack, a point where one heat treatment stopped and another began, or where there was local faulting, or any one of a dozen causes. In the case of drill rods, the actual distribution of stress must be different from that which any mathematical analysis could predict. It would seem that the spread of damage from the localized overstresses, so far as we can see now, explains the phenomenon known as fatigue. The Ideal Drill Steel By Frank H. Kingdon The essential qualities of a drill steel are: (I), It must be easily forged; (2), the forged bit end must permit easy heat treatment to obtain hardness to resist chipping; (3)) the bar or body must be stiff to resist bending or twisting and yet tough to resist shock and vibration, with resulting breakage, (4), the forged shank end must be easily heat treated to obtain hardness with great toughness. Minor requirements are that the bit and the shank are in alignment with the body; that the shank is of the proper shape and length and the shank collar or lugs of the proper diameter and length; that the hole is free from obstruction; that the striking end of the shank is flat and square; that the bit is of the proper shape, with the cutting and reaming edges formed full and to the required size; that the reaming edges are concentric with the axis of the steel, and that there are no sharp corners at the shoulder where the bit blends into the body. The essential qualities of a bit, are: That its shape be such that maximum cutting speed can be maintained for as great a distance as possible before wear of the gage and cutting edge reduces the speed of penetration to a point where a change of steel is made necessary; that the size or diameter of the drill hole corresponding to the gage of the bit can be maintained with the least possible reduction as the depth of the hole increases, and that the bit can be correctly and readily formed and heat treated. The following features of bit design require attention: Shape,

Jan 1, 1922

By William E. Horst, John H. Bassarear

A technique is described which simplifies the standard procedure for measuring the Bond work index of a specific ore and illustrates how to overcome the strict requirements regarding feed size distribution normally encountered in operating plants. Actual results obtained from various process streams in a copper concentrator are presented and the grindability data are discussed in relation to the observed plant performance. This type of information can be used to gain a better understanding of plant behavior and to assist in the evaluation of plant modifications and process control studies.

Jan 1, 1977

By G. W. Dopson, P. A. Korpi

The angular spiral lining system reduces energy consumption and grinding media consumption in grate discharge ball milk. This paper discusses the effect of this lining system on mill product size distribution. Performance comparison of a grinding circuit outfitted with angular spiral liners in ball mills are made with respect to standard double wave-liner installations. The angular spiral lining system was developed by Waagner-Biro of Austria. The installation of this lining system at Magma Copper Co. is the first of its kind in a grate discharge ball mill used for wet grinding.

Jan 1, 1983

By Dennis V. D’Andrea, Joseph L. Condon

Laboratory crater tests were performed in two-dimensional plates and three-dimensional .blocks of Holston Limestone. Fractures in the blocks were exposed by sawing through the crater region, and a technique employing dye penetrants is described for examining the resulting fracture systems in both blocks and plates. Crater fracture patterns changed from extension of radial fractures to spa11 fractures parallel to the free face as charge depths were increased. The amount of fractured rock was found to be greater than the amount determined from standard crater volume measurements. Graphs and photographs illustrate these findings.

Jan 1, 1971

By R. Steven Maxwell, Ulrich Petersen

Most minerals have experienced a slow hut perceptible decline in their annual primary production growth over the past hundred years. This decline is due to a combination of factors: (1) increased recycling; (2) exhaustion of the more accessible or higher grade ores; (3) partial substitution; (4) the more efficient use of materials; (5) progressive saturation of markets as living standards rise. Therefore, future demand for new mineral resources will probably be lower than anticipated. As the world population stabilizes, this slowdown in production growth will become even more pronounced.

Jan 1, 1979

By A. S. Nowick, E. S. Machlin

One of the main criteria used to rate the heat-resisting properties of alloys is stress rupture.' During a stress-rupture test a tensile specimen is held under a constant load at a constant temperature until it fractures. The chief measurement made during this test is the time requird for rupture at the specific test stress and temperature. It was found empirically from a series of stress-rupture tests at a constant temperature that when the logarithm of the time for rupture is plotted against the logarithm of stress a straight line is obtained within experimental error This method of showing stress-rupture data has been adopted by many investigators and the NACA.' By interpolation and extrapolation from these plots, values of the stresses required to rupture the specimens (the rupture strengths) in 10, roo, and 1000 hr are obtained for specific temperatures. Alloys are then rated for a particular application on the basis of their rupture strengths at the rupture life that most nearly represents the application. Inasmuch as stress rupture is an important criterion in rating heat-resisting alloys, it would be advantageous to know the quantitative dependence of the time lor rupture on stress, temperature, composition, and structure. In order to obtain this information, an investigation was made at the NACA Cleveland laboratory during the spring of 1945. The theory of rate processes was used because it has been found to apply to certain processes such as chemical reactions, viscous flow, and creep that occur at a definite rate for given conditions. It was thought that stress rupture was such a process. An equation was derived that gives, for a given composition and structure, the dependence of the time for rupture on stress and temperature. The investigation is part of a general program to provide information that will lead ultimately to the development of better alloys in order that the efliciency and power output of gas turbines used in aircraft propulsion can be increased. Theory The theory of rate processes will first be discussed as a general theory. It will then be shown that if stress rupture of heat-resisting alloys can be treated as a rate process, certain equations must be satisfied. Later sections will then show that these equations are satisfied. General Theory of Rate Processes The theory of rate processes5 developed by Eyring and others has been applied to chemical reactions as well as to other processes such as viscosity of liquids and diffusion. In every case in which rate-process theory can be applied, there is a small subdivision, so that the macroscopic process is the net effect of all the small processes. This smallest subdivision is called the "unit process." For example, in a chemical reaction the unit process is

Jan 1, 1948

By A. S. Nowick, E. S. Machlin

One of the main criteria used to rate the heat-resisting properties of alloys is stress rupture.' During a stress-rupture test a tensile specimen is held under a constant load at a constant temperature until it fractures. The chief measurement made during this test is the time requird for rupture at the specific test stress and temperature. It was found empirically from a series of stress-rupture tests at a constant temperature that when the logarithm of the time for rupture is plotted against the logarithm of stress a straight line is obtained within experimental error This method of showing stress-rupture data has been adopted by many investigators and the NACA.' By interpolation and extrapolation from these plots, values of the stresses required to rupture the specimens (the rupture strengths) in 10, roo, and 1000 hr are obtained for specific temperatures. Alloys are then rated for a particular application on the basis of their rupture strengths at the rupture life that most nearly represents the application. Inasmuch as stress rupture is an important criterion in rating heat-resisting alloys, it would be advantageous to know the quantitative dependence of the time lor rupture on stress, temperature, composition, and structure. In order to obtain this information, an investigation was made at the NACA Cleveland laboratory during the spring of 1945. The theory of rate processes was used because it has been found to apply to certain processes such as chemical reactions, viscous flow, and creep that occur at a definite rate for given conditions. It was thought that stress rupture was such a process. An equation was derived that gives, for a given composition and structure, the dependence of the time for rupture on stress and temperature. The investigation is part of a general program to provide information that will lead ultimately to the development of better alloys in order that the efliciency and power output of gas turbines used in aircraft propulsion can be increased. Theory The theory of rate processes will first be discussed as a general theory. It will then be shown that if stress rupture of heat-resisting alloys can be treated as a rate process, certain equations must be satisfied. Later sections will then show that these equations are satisfied. General Theory of Rate Processes The theory of rate processes5 developed by Eyring and others has been applied to chemical reactions as well as to other processes such as viscosity of liquids and diffusion. In every case in which rate-process theory can be applied, there is a small subdivision, so that the macroscopic process is the net effect of all the small processes. This smallest subdivision is called the "unit process." For example, in a chemical reaction the unit process is

Jan 1, 1948

Human progress has a visible material phase, easily discernible, that is expressed in the standard of living. This material phase, however, is only the outward expression of a spiritual or mental phase that acts as a driving force in making humanity improve both its outlook and its mode of living. The instrument of progress is the human brain. Under the urge of spiritual drive, the brain acts as a focal point to utilize the forces of nature and put them to work for the benefit of mankind. Besides intelligence, which is an innate quality, the tools of the human brain are knowledge, experience, training, initiative, and skill. Given sufficient intelligence, the human brain can make an amazing amount of progress, provided it is supplied with an adequate spiritual and moral urge and a good technical background. It is the role of education to sup- ply such a background. The material phase of human progress proceeds on a series of parallel fronts, all of them interdependent to some extent (Fig. 7). The rise of the standard of living, dependent as it is upon the manufacture and mass distribution of goods, is based essentially upon the development and utilization of the material resources of a country or land area. This development involves the extraction of mineral and organic products from Mother Earth, their transportation to manufacturing centers, their transformation into finished goods and their dis-

Jan 1, 1950

By H. W. Seamon

THE data here given were obtained by 1500 tests made, by the United Verde Copper Co. to determine the most economical air pressure for the operation of hammer drills under the varying conditions of use, and to investigate the variation in drilling speed at different air pressures Twelve models of drills were used at gage pressures ranging from 40 to 130 lb. No effort was made to harmonize theory and practice; but rather to formulate empiric rules that would cover the. average variation of the results obtained. These rules on the performance of hammer drills, based on the air pressure as the main variable, however, are not necessarily of universal application, but they apparently satisfy the results obtained in this series of tests. The drilling conditions at this property vary widely; an average of twenty-one machine shifts to a 3-ft. (0.9-m.) round has been found necessary in some of the development work, while an, advance of 56. ft. has been made in seven shifts in the "oxide" ground. This range pre-eludes the adoption of one type of drill as a standard; consequently almost every kind of hammer drill sold in this country has been tested. At present, sixteen models are in use, of which two types of the heavy (150 to 160 lb.) mounted drills, one of the light mounted drill, one stoper, and two hand plugging drills are considered as standard.

Jan 1, 1921

By L. A. Bromley, A. W. Petersen

The van Arkel-deBoer method for producing ductile titanium by thermal decomposition of Til, vapor and deposition on an electrically heated filament is modified by film boiling Til liquid on a heated filament, resulting in similar titanium deposition on the filament and liberation of gaseous iodine. The deposition rate is higher and the energy requirement smaller than in the van Arkel process. Many problems must be solved before the process is commercially feasible. TITANIUM of 99.9 pct purity, called ductile titanium, has been produced by a modification of the van Arkel-deBoer&apos; method. In the van Arkel-deBoer method, an electrically heated wire is suspended from two electrodes, which are placed in a container holding TiI, vapor at a low&apos; vapor pressure (usually <5 mm Hg). The vapor diffuses to the hot wire, usually maintained at 1100" to 1600°C,&apos; and decomposes according to the reaction liberating gaseous atomic iodine and depositing solid crystalline titanium on the wire. Estimations based on the data of Runnalls and Pidgeon,&apos; indicate that the rate-control ling step is the diffusion of atomic iodine away from the wire. There appears to be nearly thermodynamic equilibrium at the wire with TiI, and iodine as the main gaseous species. TiI, is almost certainly an important gaseous species in the cooler regions.&apos; The liberated iodine diffuses to a heated source of crude titanium and reacts to form more TiI, vapor, which again diffuses to the hot wire and completes the cyclic process. The foregoing process may be modified by suspending the hot wire in liquid TiI,, instead of the vapor, and obtaining film boiling. This type of boiling is characterized by the formation of a continuous film of vapor over the wire surface. Since only vapor contacts the wire sul.face, the temperature of this surface may be raised as high as desirable, within the limit of mechanical strength requirements for the wire. By properly adjusting the input voltage. the temperature of the wire may be maintained above U0C"C; and by evacuating the vessel holding the liquid TiI, and maintaining a suitable condenser temperature, the vapor pressure of TiI, may be held low. Thus, the conditions of operation of the van Arkel-deBoer method may be approximated with film boiling; and hence, it is postulated that ductile titanium may be produced by this method. Preparation of Til, There are many methods available for the preparation of TiI,; that used in this research was prepared by the direct reaction of titanium sponge in controlled amounts with liquid iodine. Although no difficulty was encountered with this reaction, it has since been pointed out that this method is sometimes dangerous and should be used with caution. The resulting TiI, was purified by distillation. First Film Boiling Experiments Apparatus: The apparatus shown in Fig. 1 was used for film boiling TiI, on short wire filaments. The current to the filament was supplied through a bank of three 5 kva transformers connected in parallel. The current was controlled by adjusting the voltage over a 0 to 67.5 v range with a 7 kva variable transformer on the low voltage side of the bank of transformers. The current and voltage were measured by Weston meters. The sealed-in-glass tungsten electrodes were hard-soldered to the filament for the film boiling of TiI,. The bottom part of the reactor, containing TiI,, was wrapped with ni-chrome heating wires to maintain the TiI, in the liquid state. An ice or liquid nitrogen trap, for solidifying I, vapor and any TiI, not condensed, was attached to the low pressure side of the air-cooled condenser. A Megavac vacuum pump was used. Procedure: A 0.010 in. diam tungsten filament was hard-soldered to the tungsten electrodes. TiI, was melted (mp 156°C) and poured into the reactor chamber; the top of the reactor chamber, containing the electrodes, was replaced. Freezing of the TiI, was prevented by controlling the current to the ni-chrome wires wrapped around the reactor with a 1 kva variable transformer. The mechanical vacuum pump was started and the system evacuated to about 2 mm Hg TiI, vapor pressure. The current to the filament was turned on and the impressed voltage slowly increased with the variable transformer. A sudden drop in current at nearly constant im-

Jan 1, 1957

By W. G. Lidman, H. J. Hamjian

&apos; I HE fabrication of many materials from powders involves a sintering process. A mass of powder will sinter because of the excess free energy over the same mass in the densified state caused by the higher total surface area of the powder. An understanding of the kinetics and mechanism of sintering should assist in improving the properties of such materials. The present investigation conducted at the NACA Lewis laboratory deals with the sintering of chromium carbide. Dry sintering (sintering at a temperature below the melting point) was divided into two stages by Shaler:&apos; the first stage, during which the particles preserve much of their original shape and the voids are interconnected, and the second stage, during which densification occurs and the pores are isolated. The mechanism of forming interfaces between particles, or welding together of particles, has been investigated by Kuczynski2 and may be described by any one or a combination of the following mechanisms: viscous flow, evaporation and condensation, volume diffusion, or surface diffusion. The mechanism by which pores are closed or eliminated (densification) during sintering, is of interest. Grain growth observed during sintering may be attributed to the variation in the surface energies of individual grains, causing some grains to grow at the expense of others. Grain boundary migration occurs presumably by a diffusion process, therefore the rate of grain growth would be expected to increase exponentially with increasing time and temperature. Thus, for practical sintering times of less than 1 hr, a certain minimum temperature may exist at which major structural and property changes will occur. Densification and kinetics of grain growth during sintering under pressure of chromium carbide were investigated to provide additional information which will aid in describing more accurately the sintering process and the mechanisms involved. This material was selected for this study because of the current interest in high strength, oxidation resistant refractory materials, such as carbides, which are sintered to produce solid, dense materials from powders. Sintering under pressure is a process where the heat and pressure are applied to the compact simultaneously, specimens for this work were prepared by sintering under pressure at different temperatures and for various time periods. Experimental Procedure Preparation of Specimens: Chemical analysis of the commercial chromium carbide used in this investigation was as follows: Cr 86.19 pct, C 12.14 pct, and Fe 0.2 pct. X-ray diffraction powder patterns gave characteristic diffraction lines of Cr3C2 crystal structure. Powder particle size was determined microscopically and the average initial particle size was 6 microns with 85 pct between 2 and 10 microns. Specimens sintered under pressure were formed in graphite dies3 heated by induction. Sintering temperatures were measured with an optical pyrometer by sighting into a 3/8-in. hole drilled 1 in. deep at the midsection of the graphite die. A load of approximately 1 ton per sq in. was applied to the powder. The die assembly was heated in 20 min to the highest temperature (2500°F&apos;) at which no increase in grain size could be observed, and less than 2.5 min were required to heat from this temperature to the maximum temperature (3000°F). Sintering temperatures and times for the specimens of this investigation are indicated in Table I. Analysis of Specimens: Specimens polished with diamond abrasives were etched to reveal the grain boundaries with a 1:1 mixture of 20 pct potassium hydroxide and 20 pct potassium ferricyanide heated to 160°F. Representative areas of each sample were photographed at 1000 diameters. The largest diameters of all well-defined grains were measured, but only the measurements of 15 of the largest grains were averaged in order to determine an index of grain size on the assumption that they were among the first to begin growth. Densities were determined from differential weighing of the samples in air and water. The reported density values are considered correct within ±0.01 g per milliliter. Results and Discussion Metal compacts have exhibited grain growth when sintered at temperatures about two-thirds of the absolute temperature of their melting point.&apos; Grain growth also occurs during the sintering of chromium carbide and is illustrated by the micrographs shown in Fig. 1. These micrographs were prepared from specimens sintered for 90 min at temperatures ranging from 1371°C (2500°F) to 1648°C (3000°F). Average grain size and density measurements of specimens investigated are presented in Table I. The relationship between grain size and sintering tem-

Jan 1, 1954

Discussion of the paper Of ROBERT H. BEDFORD and WILLIAM HAGUE, presented at the Salt Lake meeting, August, 1914, and printed in Bulletin No. 92, August, 1914, pp. 1807 to 1816. W. L. SAUNDERS, New York, N. Y. (communication to the Secretary *) . -Messrs. Bedford and Hague have given us a very interesting and practical paper. No better excuse for such a paper could be desired than the statement made that the expense of drilling. in this mine is one-third of the cost of delivering the ore at the mill. This statement. should be written in red letters, because it applies to a great many mines besides the one referred to and because it is generally true that in a mining plant, as also in papers read before the Institute, more attention by fat is given to the metallurgical side of mining than to the excavation of the ore, and no study of the excavation work is properly made that does not involve a careful inquiry into the merits of the rock drill used. Next in importance to the selection of a good rock drill, in a case where the actual drilling cost is one-third the cost of delivering the ore, is that. the drill should be maintained in order and kept up to its highest efficiency. The best rock chill may run down in efficiency through accidents, wear, or other conditions which are sometimes beyond supervision or control. The machine is usually in the hands of men who know how to get workout of it, not men who know how it works. The best drill runners are not machinists,. but miners. They could not tell you how the valve operates or the principle of the rotation, but they know how to get the work done. A testing machine, particularly the type described in this paper, may he of the greatest value in maintaining a uniform state of efficiency.

Jan 11, 1914

By F. H. Gilpin

SINCE Noah pitched his ark within and without with pitch, the use of asphalt in human endeavor has been increasing-for Noah&apos;s pitch was asphalt. Asphalt is a bituminous material found in nature, either pure or admixed with smaller or greater quanti-ties of mineral and non-mineral materials, or obtained by the refining of crude asphaltic-base petroleum under proper methods of control. Native or "natural" asphalts are scattered through-out the world, though the commercial value of the various deposits varies greatly, depending upon both their accessibility and magnitude and the quality of the material found. It is an acknowledged fact that such asphalts have been produced through natural causes by practically the same application of tempera-ture and pressure as are used in the modern refining of crude asphaltic-base petroleum. The best known of all the native asphalt deposits are those of Trinidad Lake in the Island of Trinidad, British West Indies, and of Bermudez Lake in Vene-zuela. Asphalt from Trinidad Lake, after refining to remove organic and some inorganic diluents, contains approximately 35 per cent, of inorganic residue, and the asphalt thus produced must be fluxed with lighter asphaltic or semi-asphaltic base oil to make it com-mercially utilizable. The refined asphalt obtained from the Bermudez Lake deposit contains from 4 to 6 per cent. of inorganic material which cannot be removed. This asphalt, also, must be fluxed to produce com-mercial products. Small quantities of similar materials are available in other locations. The best pure native asphalt&apos; is known as. gilsonite and is mined in com-mercial quantities in the State of Utah. In numerous places in the United States, particularly Oklahoma and Kentucky, there are deposits of sand¬stone and limestone impregnated with bitumen, which are known as rock asphalts. These rock asphalts may be used, particularly in the paving industry, either as found or by slight fluxing; from some deposits the asphalt is extracted and marketed commercially.

Jan 2, 1923

By P. D. Merica

IN connection with other investigations on the properties and characteristics of chilled iron car wheels, the question as to the best range of annealing temperatures was raised. Chilled-iron wheels are cast with a chill against the tread and the inside of the flange, the remainder being in sand. The composition of the metal is so chosen that under these conditions the tread and inside of the flange will show white iron to a depth of from 5/8 to 7/8 in. (15 to 22 mm.), the remainder of the wheel becoming graphitized or gray. In order to relieve the stresses set up during cooling under such drastic conditions, the wheels are stripped from the mold, while still red hot, piled in a soaking pit, and allowed to cool very slowly from their temperature at stripping. Obviously the most suitable temperature for this annealing is the highest at which no formation of graphite occurs within the white tread and at which the wheels can be stripped from the molds. Inasmuch as no direct determinations have been made of the temperatures at which the&apos; formation, of graphite takes place in white iron of compositions used in car wheels upon annealing, it was considered worth while to determine these temperatures as a means of establishing the maximum temperatures at which the annealing of the wheels may be carried out. In the course of this work, some incidental observations were made which are of interest in connection with the theory of graphitization in white iron. The literature on the subject of the formation of graphite both during cooling at casting and upon annealing is very extensive and can be best studied by reference to a comprehensive discussion of the subject by Hatfield. 1 Perhaps the most important contributions of previous investigation are the following: 1. Whether a given mass of molten iron becomes white, mottled, or gray upon casting, depends on its composition and its rate of cooling through the temperature range of solidification and immediately below.

Jan 7, 1919

By Wm. B. Price

The work of Leon Guillet concerning the effect of nickel on the structural properties of brass is checked. The best value for the coefficient of equivalence t, that is, the amount of zinc replaced by 1 per cent. of nickel, is shown to be-1.1 per cent. The best hot- and cold-working nickel silvers, varying in nickel content between the limits of 4 and 18 per cent., are tabulated and plotted diagrammatically. Also, some data are given showing a comparison between the physical properties of a hot- and cold-working low copper-nickel silver, and a commercial cold-working nickel silver containing approximately 8 per cent. more copper. THIS investigation of low copper-nickel silvers was undertaken to check the work of Leon Guillet on special brasses and to determine, more accurately, the effect of the addition of nickel on the microstructure of the binary alloys of copper and zinc. It was hoped that the results could be successfully applied to the practical production of low copper-nickel silvers. To explain the results of his investigations on special brasses, Leon Guillet evolved his conception of "fictitious compositions." He states,1 in his general conclusions, that on the introduction of a small amount of a third metal to a copper-zinc alloy, it enters into solid solution with the normal constituents up to saturation, but by so doing it brings the ternary alloy into a state microscopically equivalent to a binary copper-zinc alloy of fictitious composition, and physically more nearly like the latter than the brass containing copper-zinc in the ratio actually present. The physical properties of the ternary alloy, when compared to the same properties of an actual brass of the fictitious composition, are modified by the natural properties of the third element. Beyond the point of saturation, a special constituent appears and the above generalization no longer holds.

Jan 2, 1924

By J. W. Mills

This paper&apos;s aim is to demonstrate, by reviewing findings and conclusions of earlier authors and through recording and interpreting the outcome of recent laboratory study of the ores, that the ores around the Gem stocks are metamorphosed equivalents of common siderite-sulfide ores far from the stocks, as was first proposed by Hershey (1912, 1913). That is, all the ores probably have the Precambrian age of 1250 million years reported by Long et al. (1960). Those near the Gem stocks, however, were extensively metamorphosed in Cretaceous time during the emplacement of stocks so their resemblance and relation to other veins in the district are camouflaged.

Jan 1, 1985