Search Documents

By Jr. Baldwin. William M

WELL known to every metallurgist is the fact that different production schedules will profoundly affect the character of annealed metal strip. Yet the number of conditions [ ] that may be wrought by different combinations of rolling and annealing schedules is so myriad that despite the continual research that is being applied to this subject, the complete picture is not yet known. Copper, like all other metals, during the process of rolling or annealing, develops certain crystallographic configurations which should not be dismissed as being too impractical, for the crystallographic condition existing within the metal is a principal influence upon both the external mechanical properties and the behavior of the material [ ] when it is subjected to such operations as bending, flanging, drawing, and so forth. EFFECT OF ROLLING AND ANNEALING UPON THE CRYSTALLOGRAPHY OF COPPER STRIP The most salient points in the crystallographic reactions of polycrystalline copper to rolling and annealing may be best represented graphically by a "map" such as that given in Fig. I. I. As copper strip is cold-rolled from a randomly oriented structure (pole figure I),

Jan 1, 1942

By Donald Gilbert

PRIOR to July, 1919, the sampler at each mine of the Anaconda Copper Mining Co. in Butte did his work in his own way and was responsible to the mine foreman only. At that time, the sampling at all the company's Butte mines was placed in charge of a member of the geological department and stand-ardized methods of doing the work, were adopted. These standards were incorporated in a set of instruc-tions accompanied by blueprints representing typical conditions. The main features of the instructions were as follows: All samples to be cut at breast height and horizontally, regardless of dip of vein, and the horizontal width reported. A single sample to include not more than a 5-ft. width of the breast and to weigh not less than 4 lb. for this width. Where the vein is made up of two or more streaks of different hardness or mineral content, each streak is to be sampled sepa-rately and the average value of the combined width figured. If two streaks of ore are separated by a streak of waste, which is not sampled, in obtaining the average value of the breast the waste must be figured in with a zero assay. Drifts to be sampled in the breast after each round. Raises to be sampled for each floor raised. Each end to be sampled separately and the average width and value of the two ends to be used as the average of the floor. All veins cross-cut to be sampled along the side of the cross-cut, at breast height and horizontally. Where the vein strikes at an acute angle to the line of the cross-cut, the width of sample must be corrected to show the horizontal width at right angles to the line of strike of the vein. Rill stopes must be sampled across the full mining width. In square-set stopes, each set must be sampled separately along the line of the caps. Waste portions of the vein which are mined for filling must not be included in the sample.

Jan 2, 1922

By Tracy C. Jarrett

In making gold alloys possessing certain physical properties, such i~nportant factors as corrosion resistance, color, hardness and melting points must be considered. All of these requirements depend directly upon the composition. It is possible to obtain the same colored gold alloy by using different compositions, but in doing so one may bring in some undesirable property. Other investigations have been carried on in this field by F. E. Carter,' E. M. Wise12 and L. Sterner-Rainer2 To make a complete study of the effect of composition upon these properties, a systematic investigation was carried on involving a range of copper content from 85 to 65 per cent. Elements such as zinc, silver and nickel were used to replace in part the copper content. The gold content in all the alloys remained constant. Only 10-karat gold alloys of those containing 41.6 per cent gold will be considered. All of the alloys were made in an induction furnace. Each alloy was cast in a 3 by 1/4 by 3/4-in. ingot. The method of obtaining the melting points and making color determinations was described in a previots paper.4 The Rockwell B scale with the 1/16-in. ball and 100-kg. weight was used for all hardness determinations. The submersion of test pieces in concentrated nitric acid is one of the standard corrosion tests used in the optical trade. A test piece in the 50 per cent cold-worked condition, % by 2 by 0.045 in., is blanked from a skip using a die, and the weight loss per square inch of surface is taken as a means of comparison. The time for this test is 2 1/2 hr. of actual submersion of the test picce in the acid. This standard test was applied to all of the 10-karat gold alloys discussed in this paper. The tensile tests were made upon strips of the dimensions shown in Fig. 1. The test pieces after blanking were annealed at 1300" F. for 20 min. and cooled in air. Thc "drop of the beam" method was used in determining the yield point, as there was a very marked "drop" when the yield point was reached.

Jan 1, 1940

By Tracy C. Jarrett

In making gold alloys possessing certain physical properties, such i~nportant factors as corrosion resistance, color, hardness and melting points must be considered. All of these requirements depend directly upon the composition. It is possible to obtain the same colored gold alloy by using different compositions, but in doing so one may bring in some undesirable property. Other investigations have been carried on in this field by F. E. Carter,' E. M. Wise12 and L. Sterner-Rainer2 To make a complete study of the effect of composition upon these properties, a systematic investigation was carried on involving a range of copper content from 85 to 65 per cent. Elements such as zinc, silver and nickel were used to replace in part the copper content. The gold content in all the alloys remained constant. Only 10-karat gold alloys of those containing 41.6 per cent gold will be considered. All of the alloys were made in an induction furnace. Each alloy was cast in a 3 by 1/4 by 3/4-in. ingot. The method of obtaining the melting points and making color determinations was described in a previots paper.4 The Rockwell B scale with the 1/16-in. ball and 100-kg. weight was used for all hardness determinations. The submersion of test pieces in concentrated nitric acid is one of the standard corrosion tests used in the optical trade. A test piece in the 50 per cent cold-worked condition, % by 2 by 0.045 in., is blanked from a skip using a die, and the weight loss per square inch of surface is taken as a means of comparison. The time for this test is 2 1/2 hr. of actual submersion of the test picce in the acid. This standard test was applied to all of the 10-karat gold alloys discussed in this paper. The tensile tests were made upon strips of the dimensions shown in Fig. 1. The test pieces after blanking were annealed at 1300" F. for 20 min. and cooled in air. Thc "drop of the beam" method was used in determining the yield point, as there was a very marked "drop" when the yield point was reached.

Jan 1, 1940

By Tracy Jarrett

IN making gold alloys possessing certain physical properties, such important factors as corrosion resistance, color, hardness and melting points must be considered. All of these requirements depend directly upon the composition. It is possible to obtain the same colored gold alloy by using different compositions, but in doing so one may bring in some undesirable property. Other investigations have been carried on in this field by F. E. Carter,1 E. M. Wise,2 and L. Sterner-Rainer.3 To make a complete study of the effect of composition upon these properties, a systematic investigation was carried on involving a range of copper content from 85 to 65 per cent. Elements such as zinc, silver and nickel were used to replace in part the copper content. The gold content in all the alloys remained constant. Only 10-karat gold alloys of those containing 41.6 per cent gold will be considered. All of the alloys were made in an induction furnace. Each alloy was cast in a 3 by ¼ by ¾ -in. ingot. The method of obtaining the melting points and making color determinations was described in a previous paper.4 The Rockwell B scale with the ball and 100-kg. weight was used for all hardness determinations. The submersion of test pieces in concentrated nitric acid is one of the standard corrosion tests used in the optical trade. A test piece in the 50 per cent cold-worked condition, ½ by 2 by 0.043 in., is blanked from a strip using a. die, and the weight, loss per square inch of surface is taken as a means of comparison. The time for this test is 2 ½ hr. of actual sub-mersion of the test piece in the acid. This standard test was applied to all of the 10-karat gold alloys discussed in this paper. The tensile tests were made upon strips of the dimensions shown in Fig. 1. The test pieces after blanking were annealed at 1300° F. for 20 min. and cooled in air. The "drop of the beam" method was used in determining the yield point, as there was a very marked "drop" when the yield point was reached.

Jan 1, 1939

By A. R. Anderson

UNTIL recently all discussions directed at justify-ing the use of mechanical-loading equipment and conveyors have referred chiefly to tons per man and cost per ton. But there is another consideration that ? will speed the adoption of mechanical loading in mines even though tons per man on present day stand-ards were not increased nor the cost per ton decreased. With restricted immigration, improved facilities for education in our mining communities, and increased opportunities for recreation, the type of man who can or will throw 20 tons of coal per day over the side of a mine car is disappearing. Whether we will it or not provision must be made to replace muscular effort by mechanical means. Fortunately, indications are that the process will be accompanied by increased output per man and lower production cost, and though the outlook may now be a bit clouded in spots, all should profit by the change. The operator should enjoy a more stable business with more assured profit, the miners should get a better livelihood with less arduous effort and under safer and pleasanter working conditions, and the consumer should gain the assurance of a supply of coal always available at reasonable prices. That sounds like the millennium in the coal business perhaps. Of course, it is not, but there is just enough of that millennium stuff in it to encourage those of us who are working with today's problems of applying loading and conveying equipment to underground opera-tions. If we discern clearly that there can be no back-sliding, and that all will share in whatever advantages accrue, we will carry on more vigorously, and may right-fully expect to have the necessary cooperation of all the elements within the industry. As nature does not seem to have followed a definite plan in the formation of coal deposits it is not likely that any one standard method or type of equipment can be evolved for mining the coal. The method of mining that maybe most advantageously employed with load-ing machines and conveyors depends on the character of the strata overlying the coal as much as anything else.

Jan 4, 1927

By W. B. Price

AT the New York meeting of the American Institute of Mining and Metallurgical Engineers held in February, 1926, W. H. Bassett and J. C. Bradley presented a paper entitled "Exudations on Copper Castings."' The purpose of the present paper, as the title suggests, is to call attention to somewhat similar phenomena which the authors have encountered in brass and bronze. From a study of the examples given, a more-or-less speculative theory of "inverse segregation" is advanced. Protuberances on Admiralty Brass In the rolling mill of the Scovill Manufacturing Co., there have been found quite commonly bars of certain alloys which had a sort of shaggy roughness on the surface due to slight metallic protuberances. No special attention was paid to these until some bars were found on which these protuberances were heavy enough at the bottom of the bars to produce a blistered appearance. A sample of the protuberances was milled off the surface of the bar illustrated (Fig. la) and upon analysis was found to contain 66.66 per cent. copper, 4.02 per cent. tin and 0.03 per cent. lead, whereas the average composition of the bar was 70.21 per cent. copper, 1.21 per cent. tin, and 0.01 per cent. lead. A sample of the shaggy-rough protuberances at the very top of a bar was also analyzed and was found to contain 2.45 per cent. tin, indicating that it was probably of the same origin as the blistered areas. These results were not entirely unexpected for previous analyses of this alloy had revealed that the surface was richer in tin than the rest of the bar. This, of course, is contrary to what we would expect from a consideration of the equilibrium diagram and has been called "inverse segregation." Fig. 16 is a cross-section of a bar through the protuberances on the surface. It reveals that there is a decidedly different structure through the raised areas and seems to indicate that the bar originally solidified

Jan 1, 1927

By T. B. Counselman

C. G. McLachlan—In the foregoing paper the author has presented a very neat method for calculating the solution recovery for a countercurrent flowsheet. He has, however, based his calculations, as he states, on the assumption that "the concentration of dissolved value must be exactly the same in the overflow and underflow of any thickener." This assumption, which is usually made regardless of the type of calculation used, is "not strictly correct because diffusion of the dissolved gold in the solution associated with the solids as it progresses through the countercurrent system is far from being instantaneous, with the result that on a ton for ton basis, the assay of the solution in the thickener underflow is higher than in the corresponding thickener overflow. An agitator introduced into the flowsheet between thickeners will reduce, but not entirely eliminate, this difference. In practice we have found that the best way to take care of this condition— in addition to the use of one or more intermediate agitators—is to circulate 20 pct or 25 pct more solution than called for by the cheoretical calculation. This presents no difficulty provided that adequate thickener capacity is provided in the original design of the countercurrent circuit.

Jan 1, 1951

By T. B. Counselman

C. G. McLachlan—In the foregoing paper the author has presented a very neat method for calculating the solution recovery for a countercurrent flowsheet. He has, however, based his calculations, as he states, on the assumption that "the concentration of dissolved value must be exactly the same in the overflow and underflow of any thickener." This assumption, which is usually made regardless of the type of calculation used, is "not strictly correct because diffusion of the dissolved gold in the solution associated with the solids as it progresses through the countercurrent system is far from being instantaneous, with the result that on a ton for ton basis, the assay of the solution in the thickener underflow is higher than in the corresponding thickener overflow. An agitator introduced into the flowsheet between thickeners will reduce, but not entirely eliminate, this difference. In practice we have found that the best way to take care of this condition— in addition to the use of one or more intermediate agitators—is to circulate 20 pct or 25 pct more solution than called for by the cheoretical calculation. This presents no difficulty provided that adequate thickener capacity is provided in the original design of the countercurrent circuit.

Jan 1, 1951

By George H. Ashley

At the beginning of the war, about 13 years ago, a conference was called in Washington to lay plans for pooling the coals of the United States. A careful review of the various systems of classification then extant showed none well adapted to the needs of coal pooling. The system of Tidewater pools then adopted, using numbers to distinguish one pool from another, was based on typical coals of different localities. At that time, the writer undertook the preparation of such a practical classification. Aside from drawing on his experience of over 20 years in the coal fields of the United States, reaching from the Pacific Coast and the Rio Grande to Rhode Island, he first examined and carded all of the large collection of coals in glass jars made by and for M. R. Campbell. Next, he carded all of the descriptions of coals he could find in the U. S. Geological Survey bulletins and elsewhere, as well as practical tests of coals by the Navy and other organizations and then took account of every published coal analysis of the U. S. Geological Survey and U. S. Bureau of Mines. A study of this information, involving thousands of recomputations, led to the presentation of a paper on "A Use Classification of Coal" before this Institute at the Chicago meeting, September, 1919. That classification was unique (1) in a classification based on "standard coal" which included moisture, but used standardized ash, sulfur and nitrogen, (2) in using physical properties to distinguish the major classes or orders, (3) in recognizing British thermal unit values in the minor subdivision, (4) in the large number of classes recognized (thirty-six), (5) in proposing mineral names for all classes, (6) in proposing a letter code for the several classes for practical use, (7) in proposing a code for expressing what has commonly been called "grade" of the coal, the grade code to be combined with the rank code to designate and describe a coal. The writer still thinks that the principles then offered, though not necessarily the exact proposals, are valid and desirable in any practical classification. The actual classification of coal by rank was based on the ratio of fixed carbon to volatile matter for the high-rank coals—the well-known

Jan 1, 1930

The primary purpose of the Institute is to advance the technologic and engineering arts embraced by it through interchange of knowledge This can best be done by the presentation and discussion of technical papers by its members Short practical papers are especially welcome An author should always satisfy himself that his material is of a quality that will be a credit to him and to the Institute The preparation of a good paper frequently leads to a reorientation of the author's thoughts, and publication contributes much to the professional standing of the author Members are urged to submit papers presenting the results of their work Attention to the following suggestions will greatly further the prompt and efficient handling of manuscripts

Jan 1, 1952

The primary purpose of the Institute is to advance the technologic and engineering arts embraced by it through inter- change of knowledge. This can best be done by the presentation and discussion of technical papers by its members. Short practical papers are especially welcome. An author should always satisfy himself that his material is of a quality that will be a credit to him and to the Institute. The preparation of a good paper frequently leads to a reorientation of the author's thoughts, and publication contributes much to the professional standing of the author. Members are urged to submit papers presenting the results of their work. Attention to the following suggestions will greatly further the prompt and efficient handling of manuscripts.

Jan 1, 1946

By D. W. Duncan, A. Bruynesteyn

An ore containing chalcopyrite was microbiologically leached in 6 ft columns at particle sizes ranging from -2 +1 ½ inches, to -3/8 + 3/16 inches. The rate of leaching increased exponentially as the particle size decreased. The controlling factor was the active leaching volume made up of the particle surface area and the depth of penetration of the bacteria and leach liquor into the particle. This volume became an increasingly larger part of the total volume as the particle size decreased. The sample under test leached poorly at larger particle sizes and it was calculated that under commercial conditions, it would produce at best a pregnant solution containing 100 mg/l (0.2 lb/ ton) of copper per 100 ft of dump height.

Jan 1, 1974

By G. Derge, R. E. Grace

Diffusivity of bismuth in liquid Pb-Bi alloys has been measured by the capillary reservoir method as a function of temperature and composition. Fair agreement between theory and experiment is found for the measured diffusion coefficients and activation energies of diffusivity and viscosity in dilute lead alloys. The measured diffusion coefficients in the high bismuth alloys describe mass transport in special concentration gradients. THE study of diffusion in liquid metals has been restricted largely to the amalgams over small ranges of temperature and composition. In contrast to this, diffusion and transport of ions and molecules in aqueous and organic solvents have been studied extensively for the past 50 years. The general difficulty of measuring diffusion coefficients in both gases and liquids at high temperatures has been that of eliminating convection currents. Measuring techniques based on freezing and sectioning after the diffusion period1 are not particularly satisfactory because of the volume changes and segregation which occur during freezing. The most promising technique which is currently being developed for liquid metals is the capillary reservoir method. This eliminates convection currents from the diffusion zone and requires measurements only of the length and initial and final compositions of the alloy within the capillary. Anderson and Saddington' have measured the diffusion coefficient of tungstate anions in aqueous Na,W04; Wane4' and Hoffman- ave studied structure and self-diffusion in water and self-diffusion in mercury, respectively, by similar techniques. Selection of the Pb-Bi system for initial study was made for several reasons: I—It afforded a low temperature system for development of techniques which would be suitable for high temperature measurements in liquid iron. This research on diffusion in liquid iron is now in progress as a part of a general program on the rates and mechanisms of slag-metal reactions. 2—Activity data on liquid Pb-Bi alloys of all compositions are available from the emf meas- urements of Strickler and Seltz.9 3—Some data are available on the diffusion of bismuth into solid lead. The measurements on solid alloys were made by von Hevesy and Seith7 for the concentration range of 0 to 2 pct Bi. An appropriate solution to Fick's law (unsteady state) for the capillary reservoir has been found by considering the mass flow which passes through a unit area of surface on a slab of infinite thickness as a function of time. This is the first application of this solution to diffusion measurements, although a similar solution is available for identical boundary conditions.' By analogy with heat conduction, the problem reduces to a perfectly insulated infinite slab at temperature C,, one surface of which is quenched to C, for all times, t. Heat is permitted to flow from quenched surface of the slab to an infinite supply of coolant at C.' (see Appendix). For the corresponding solution for diffusion in liquids, these terms become Where Cu is the initial concentration of component A" in entire capillary at t - 0, C, is the final con- In this case. component A is bismuth, and C, = 0. centration of component A in entire capillary at t = t, C, is the concentration of component A in bath for all t, 1 is the length of the capillary in centimeters, t is the time of diffusion period in seconds, and D is the diffusion coefficient in square centimeters per second. By comparison with solutions to Fick's law used in the solid state, this solution for liquids is similar to the Grube solution for solids, where the change in D with chemical composition is not taken into consideration. Difficulty is to be expected if large concentration gradients are employed and if the concentration gradients extend over an appreciable length of the capillary.

Jan 1, 1956

By D. G. Westlake

Resistance was measured as a function of temperature, 77° to 350°K,for niobium with hydrogen concentrations up to 3.76 at. pct. Cooling curves exhibited a discontinuity in slope that was attributed to the initiation of hydride formation. A thermal hysteresis was explained in terms of diffusion and the effects of mechanical constraint on nucleation and growth. The heat of solution of hydrogen in saturated Nb-H solid solution was 2. 737 * 0.045 kcal per g-atom, including an unknown stress contribution. The critical ternperatures for hydride formation during cooling and for embrittlement are correlated but not coincident. This, too, has been explained in terms of mechanical constraint and stress-itlduced tratzsfomtation. Nb-H alloys undergo a ductile-brittle transition with decreasing temperature.'-3 Similar behavior has been noted for v-H.1,5 For the latter system, there is evi-dence6 suggesting coincidence of the temperature of minimum ductility and the critical temperature T, for initiation of metal hydride precipitation during cooling. A decrease in ductility due to the presence of brittle hydride particles is readily explainable. The fact that ductility begins to decrease at some temperature higher than T,4,5 has led us6 to suggest that precipitation may be strain-induced locally during tensile testing. Wood and Daniels' have reported that a plot of temperatures for 10 pct reduction in ductility vs hydrogen concentration in niobium is not coincident with, but parallels, the solvus.7,8 They believe this indicates a correlation of precipitation and embrittlement. Unfortunately, the two reported solvuses 7,8 to which Wood and Daniels refer are not in agreement with each other. Furthermore, neither solvus was determined experimentally: each was a plot of calculated solubilities. Thus. neither is highly dependable for determining whether embrittlement coincides with initiation of hydride precipitation. Longson 9 studied phase relations in the Nb-H system between 77° and 473°K by dilatometry. Comparison with metallographic observations convinced him that discontinuities in the slopes of his dilatometric plots were coincident with the initiation of hydride precipitation. Plotting the logarithm of the hydrogen concentration vs the reciprocal of the temperature at which precipitation was initiated during cooling, he obtained a straight line shown in Fig. 1. Walter and chandler,'' using X-ray techniques to detect the for mation of a second phase? have obtained three experimental points in the temperature range 295° to 338°K which fall within Longson's experimental error for this plot. A similar plotg of temperatures at which dissolution was completed during heating was a parallel line shifted toward higher temperatures. A straight-line plot was obtained, also, for the temperatures of the ductile-brittle transitions,9 but it was shifted toward still higher temperatures. Longson calculated an activation energy of 2.980 * 0.300 kcal per mole for the hydrogen embrittlement mechanism, compared with 3.180 * 0.400 kcal per mole for hydride formation. Despite this agreement, he concluded, "It seems unlikely that embrittlement results from hydride formation..." because hydrogen embrittlement was observed at temperatures above the solvus. It is our contention that embrittlement is correlated with precipitation of the hydride.6 Because only Longson has investigated Nb-H phase relations at sub-ambient temperatures, we deemed it advisable to re-determine the temperature dependence of the solubility using the resistometric technique already proven successful for the V-H system.6 Coincidence of our solvus with temperatures for embrittlement would

Jan 1, 1970

By Lawrence W. Teufel

An anelastic strain recovery technique is presented as a method of determining the directions and ratio of the maximum and minimum horizontal in-situ stresses from oriented cores from deep wells. Predictions of hydraulic fracture azimuth inferred from principal stress directions determined from both elastic and time-dependent (anelastic) strain relaxation measurements of volcanic tuff are consistent with the observed orientations of hydraulic fractures produced in simulation and mineback experiments, underground at the Nevada Test Site. In addition, anelastic strain recovery measurements on oriented cores of shale and sandstone from well depths of about 1680 meters show consistent relaxation directions of the principal horizontal strains and have enabled a prediction of the principal horizontal stress directions and hydraulic fracture azimuth.

Jan 1, 1982

By G. Sachs, C. C. Chow, L. J. Klingler

Most structural parts which are heat treated are designed using strength properties which have been determined in the principal direction of the wrought material. For example, for rolled or drawn materials, properties are given for the rolling or drawing direction. The structures, however, may be loaded so that the critical stress is in some direction other than that for which the properties of the material are known. Investigations of forged products,123 have shown that while the yield strength and tensile strength of carbon steel billets and bars vary little with the direction of the test specimen in relation to the fiber, the contraction in area in tension tests and the impact strength in notched bar impact tests decrease in the transverse direction. The contraction in area and, consequently, the fracture stress of hard aluminum and magnesium alloy forg-ings have also been found to be lower in the transverse direction. An investigation on aluminum alloy plate4 likewise has shown the dependence of the fracturing characteristics upon the direction* of the test specimens, the longitudinal direction being considerably stronger than the transverse direction and the normal direction, with the normal direction being the least strong. The variation of properties with direction has been explained by a type of anisotropy called mechanical anisot-ropy. This anisotropy results from the elongation, in the direction of the principal strain, of certain phases, inclusions, and/or cavities in the metal during working. A mechanical fibering is thus produced which seems to persist through annealing and heat treatment. This investigation was initiated to determine the flow stress and fracture stress, at high hardness levels, at 90° to the rolling direction in a round steel bar. It is this direction which receives the critical stress in drawing dies machined from round bars. Preliminary tests showed a large difference in properties between the 0° and 90° directions. Consequently, it was felt that a more complete investigation, utilizing several types of tests, was warranted to determine the flow and fracture characteristics of a steel at various orientations, for a number of hardness levels. This investigation was conducted on an air hardening nondeform-ing die steel. Material and Procedure The distribution of properties was made on a 3-in. round bar of annealed high-carbon, high chromium steel of the following analysis: Pct Carbon................... 1.53 Manganese................ 0.39 Silicon.................... 0.27 Chromium................ 11.76 Vanadium................. 0.25 Molybdenum.............. 0.81 The 3-in. bar was produced from an 8-in. ingot, which was annealed and forged to a 4-in. square billet. The billet was annealed and rolled to a 3-in. round which was then annealed and straightened. This steel is an air hardening die steel which has very good dimensional stability on hardening; therefore, the residual stresses resulting from hardening would be expected to be low. A hardness survey across the diameter of the annealed bar showed no difference in hardness from the center to the outside. However, the test sections of all the specimens were taken approximately half way between the center of the bar and the surface to avoid any surface effect or possible porosity at the center. Tension, compression and bend tests were made on specimens hardened and tempered at six different temperatures. The tension test specimens, Fig 1, were machined from the bar at orientations of 0, 22.5, 45, 67.5 and 90° from the axis of the steel bar. The specimens were rough machined, heat treated and then ground to size. The test section on each specimen was lapped in a direction parallel to the axis of the specimen to remove any transverse scratches which might act as stress raisers. The specimens were tested in fixtures which insured concentricity of loading of less than 0.001 in.5 The transverse strains were measured with a radial strain gauge,5 the least count of which was 0.0001 in. change in diam. The compression specimens, Fig 1, were machined from the bar at ori-

Jan 1, 1950

By W. E. C. Coxe

At the meeting of the Institute in Philadelphia, in June, 1876, it was my pleasure to read a paper on the "Manufacture and Endurance of Iron Rails." I then spoke of some trial rails which had been placed in the down track of the Philadelphia and Reading Railroad, over which passed, in addition to merchandise and passengers, most of the heavy coal traffic of that company. One of these rails, made at the Philadelphia and Reading Rolling Mill in 1870, and then placed in the track, was removed in 1876, after having carried about 55,000,000 gross tons, and was on exhibition at the Centennial Exhibition. A piece of this worn rail, twisted cold, was also shown there. One of the same series of rails was allowed to remain in the track until 1878, and short sections of this rail, as well as one not worn, to show its original shape, are presented for your inspection. A comparison of the two will show that the top of the head or tread has morn down 3/16ths of an inch during its nine years of service. It carried in that time 67,000,000 gross tons of freight, passengers, cars, and engines. This rail was made in the usual way of manufacturing iron rails at the Philadelphia and Reading Rolling Mill. The head was made from puddled iron bars, piled, heated, and rolled into bars, 41/2 and 3 inches wide by 1 inch thick, these bars, breaking joints, were made into a pile in section 9 inches square, heated and rolled into slabs 9 inches wide and 2 inches thick; the balance of the rail-pile was made of 41/2 and 3-inch bars, rolled from two-thirds old rails and one-third puddled iron, the

Jan 1, 1880

By W. E. C. Coxe

AT the meeting of the Institute in Philadelphia, in June, 1876, it was my pleasure to read a paper on the "Manufacture and Endurance of Iron Rails." I then spoke of some trial rails which had been placed in the down track of the Philadelphia and Reading Railroad, over which passed, in addition to merchandise and passengers, most of the heavy coal traffic of that company. One of these rails, made at the Philadelphia and Reading Rolling Mill in 1870, and then placed in the track, was removed in 1876, after having carried about 55,000,000 gross tons, and was on exhibition at the Centennial Exhibition. A piece of this worn rail, twisted cold, was also shown there. One of the same series of rails was allowed to remain in the track until 1878, and short sections of this rail, as well as one not worn, to show its original shape, are presented for your inspection. A comparison of the two will show that the top of the head or tread has worn down 3/16 ths of an inch during its nine years of service. It carried in that time 67,000,000 gross tons of freight, passengers, cars, and engines. This rail was made in the usual way of manufacturing iron rails at the Philadelphia and Reading Rolling Mill. The head was made from puddled iron bars, piled, heated, and rolled into bars, 4 1/2 and 3 inches wide by 1 inch thick, these bars, breaking joints, were made into a pile in section 9 inches square, heated and rolled into slabs 9 inches wide and 2 inches thick; the balance of the rail-pile was made of 4 1/2 and 3-inch bars, rolled from two-thirds old rails and one-third puddled iron, the

Jan 1, 1880

By Halbert Powers Gillette

FROM the known laws of physical chemistry I believe it can be shown that progressive mass movement of water solutions in channels has seldom been the means of ore-concentration in veins. It is my purpose in this paper to show that the force known as “osmosis” has been the principal factor in ore-formation. Convection-currents have doubtless supplemented osmosis, and the two working together have been the agencies that have gathered the scattered particles of rare minerals into the larger masses which are called ore. Osmosis is commonly thought of as a vague, feeble force that causes slow diffusion of dissolving matter through the solvent. That it is a measurable force, often of great intensity, few know, except those who are familiar with the laws of modern physical chemistry. Therefore, I may be pardoned for going briefly into the elementary mathematics of osmotic pressure and of convection-currents. The velocity of water moving through any channel is given by the Chézy formula: (1) v = c [/rs], in which r is the hydraulic mean radius; s, the slope of the channel in which gravity is the sole propulsive force; and c, the coefficient of roughness of the sides of the channel. From this formula it is evident that the smaller the channel, the smaller the velocity of water under a constant head. In rock-crevices, therefore, where the head is constant, water moves much more slowly than in large fissures, and in moving through sand or porous rock it is to an even greater degree retarded. Hence, if a mass of water-saturated sand be heated, the finer the sand-grains, the more slowly will the temperature rise at parts remote from the source of heat. Conversely, cooling is retarded the smaller the interstices or channels through which the convection-currents move. The importance of this

Jan 1, 1913