Search Documents

By J. H. Fletcher, S. M. Cassidy

Air has been cooled, heated, washed, humidified and dehumidified for many purposes and in many industries. At a number of metal mines air is conditioned to reduce the high humidity and unbearable heat found in deep workings, and at some mines air is washed to allay siliceous dust. Steam is introduced into the intake air at many coal mines, particularly in winter, for the purpose of keeping loose coal dust so moistened that the hazard of an explosion is lessened. This paper will describe a further successful application of air conditioning in a coal mine, where, for over three years, all intake air has been cooled to a constant temperature for the sole purpose of preventing roof falls. Effect of Warm Weather on Mine Roof It is generally known by mining men that some, if not all, coal mines have more trouble from bad roof during the warm summer months than in winter. Also, it has been observed that roof on intake airways is usually worse than on the return entries, after the air has circulated through the mine. Some mines and some coal seams are much more affected than others. In the Clinton district of Indiana, the No. IV coal seam has a good, firm, gray shale roof except during the summer months, when it deteriorates badly and falls in small slabs 1 to 6 in. thick. Timbering is not very efficacious during this period because in time the roof will shear around the supporting prop or crossbar and either dislodge the timber or leave it supporting only a few inches of crumbly shale (Fig. 1). This action is renewed each summer, choking airways with fallen slate, tearing down trolley wires, hampering haulage, endangering men and adding considerably to the deadwork cost. Only when mines have been worked for a period of years and have been advanced a long distance from the shaft do the active workings become comparatively free of this trouble, and even then the intake entries are still a source of much deadwork. Such was the annoying situation at the mine of the Saxton Coal Mining Co. operated in the No. IV coal just north of Terre Haute, Ind. During the months of warm weather it was possible to stand at any quiet spot in the mine and within 10 min. hear at least two or three falls,

Jan 1, 1931

By J. Chipman, N. J. Grant, R. Rocca

Desulphurization of liquid iron by reducing slags of the electric-furnace type was studied from 65 heats. Variations were made in basicity over a wide range and in FeO up to about 5 pct for their effects on desulphurization. The role of FeO in desulphurization from the blast furnace, to the electric furnace, to the oxidizing conditions of the open hearth is shown to fit a relatively simple pattern of behavior. THE mechanism which controls the desulphurization of molten iron by basic slags has been the object of several investigations. In particular, equilibrium determinations have been made both in the field of basic open-hearth slags, which have a high iron-oxide concentration, and in the field of blast-furnace slags which have a very low iron-oxide concentration. In both cases the desulphurization ratio has been found to increase with increasing basicity of the slags; however, the mechanism of desulphurization differs in the two cases. In basic open-hearth slags desulphurization occurs mainly as a partition of iron sulphide:&apos; FeS * (FeS) and the desulphurization ratio is approximately independent of iron-oxide concentration in the slag. In blast-furnace slags the concentration of iron oxide is very low as a result of the highly reducing conditions in which they are formed. The controlling reaction for desulphurization is then:2,3 FeS + (CaO) <=* (CaS) + (FeO) The slags of the reducing stage in the electric furnace have an iron-oxide concentration which is intermediate between blast-furnace and open-hearth slags. The study of the mechanism of desulphurization for these slags has been the object of this investigation. The importance of low (FeO) in the slag for desulphurization was first verified by Bardenheuer and Geller,& who found that high desulphurization ratios were obtained in highly reduced slags. It was recognized" hat iron oxide in the slag becomes a controlling factor in desulphurization only at FeO concentrations approximately under 5 pct. A recent investigation conducted by Buehl,7 upon the suggestion of one of the authors, confirmed this opinion from the results obtained from a heat conducted in a small arc furnace. In the present investigation, slags of very high basicity, such as often are encountered in the basic electric furnace, could not be studied, but equilibrium data have been obtained for slags in a wide basicity range. The iron-oxide concentration in these slags ranged from 0.08 to 15 pct and was controlled by the addition of silicon to the metal. Other constituents of the slags were mainly CaO, MgO, SiO2, A120,, and CaF,. The experimental technique was essentially the same as that of previous investigations.1 8-lo In an open magnesia-lined induction furnace, 65 lb of Armco ingot iron was melted. An atmosphere of hydrogen was maintained over the melt for 1 hr to bring the carbon content down to approximately 0.010 pct maximum. The bath then was exposed to air for 25 min to remove hydrogen. The electrodes were put in place, and the furnace was operated from this point on in an atmosphere of nitrogen. A synthetic slag was added to which additions of silicon and iron sulphide were made. A rate study conducted at the beginning of this investigation had

Jan 1, 1952

By I. Lowthian Bell

THERE has been probably no improvement introduced into the manufacture of iron which created more surprise in the minds of practical smelters and of scientific men than Neilson&apos;s discovery of the hot blast. In 1829, Messrs. Dunlop & Co. consumed at the Clyde Works, near Glasgow, nearly 7 3/4 tons of coal to make a ton of pig iron, of which about 20 cwts. was employed under the boilers of the blowing engines, leaving nearly 7 tons for the consumption of the furnace itself. In the year 1833, by heating the air to 612° F. (322° C.), they reduced the 7 3/4 tons to 3 tons by the mere burning of 8 cwts. of coal in the apparatus for raising the blast to this temperature. The statement just given is strictly true in a commercial sense, but when we come to consider the question as one of physical science, it is necessary to eliminate some of the conditions which conduced to so extraordinary a result. Anterior to Neilson&apos;s time the fuel employed in smelting iron was coke, and it was supposed at that period, erroneously, however, that coal in its raw state, when burned with cold air, was totally unfit for the purpose in question. This mineral, as it was obtained from the Lanarkshire coal-field, contained about 35 per cent. of volatile matter, but the process of charring it was performed in so unskilful a manner that instead of receiving 88 cwts. of coke from 135 cwts. of coal, 60 cwts. only was the product of the operation. Again, the reduced consumption of carbon in the furnace itself was accompanied by a corresponding diminution of blast, and this was followed by an economy of half a ton in engine coal. After making a proper allowance, however, for all these collateral circumstances, we are within the mark when we admit that in actual coke, which is really the form the fuel has to assume before it is burnt in the blast-furnace, not less than 30 cwts. was saved by heating the blast to 615° F. (322° C.). This unexpected economy, be it remembered, was obtained by the combustion of the 8 cwts. of coal, somewhat wastefully applied in the hot-air apparatus. Numerous have been the opinions advanced by different authorities in the scientific world to account for the apparent anomaly, but none,

Jan 1, 1877

By I. Lowthian Bell

THERE has been probably no improvement introduced into the manufacture of iron which created more surprise in the minds of practical smelters and of scientific men than Neilson&apos;s discovery of the hot blast. In 1829, Messrs. Dunlop & Co. consumed at the Clyde Works, near Glasgow, nearly 79 tons of coal to make a ton of pig iron, of which about 20 cwts. was employed under the boilers of the blowing engines, leaving nearly 7 tons for the consumption of the furnace itself. In the year 1833, by heating the air to 612&apos; F. (322&apos; C.), they redoccd the 79 tons to 3 tons by the mere burning of 8 cwts. of coal in the apparatus for raising the blast to this temperature. The statenlent just given is strictly true in a commercial sense, but when we come to consider the question as one of physical science, it is necessary to eliminate some of the conditions which conduced to so extraordinary a result. Anterior to Neilson&apos;s time the fuel employed in smelting iron was coke, and it was supposed at that period, erroneously, however, that coal in its raw state, when burned with cold air, was totsally unfit for the purpose in question. This mineral, as it was obtained from the Lanarkshire coal-field, contained about 35 per cent. of volatile matter, but the process of charring it was performed in so unskilful a manner that instead of receiving 88 cwts. of coke from 135 cwts. of coal, 60 cwts. only was the product of the operation. Again, the reduced colisumption of carbon in the furnace itself was accompanied by a corresponding diminution of blast, and this was followed by an economy of half a ton in engine coal. After making a proper allowance, however, for all these collateral circumstances, we are within the mark when we admit that in actual coke, which is really the form the fuel has to assume before it is burnt in the blast-furnace, not less than 30 cwts. was saved by heating the blast to 615° F. (322° C.). This unexpected economy, be it remembered, was obtained by the combustion of the 8 cwts. of coal, somewhat wastefully applied in the hot-air apparatus. Numerous have been the opirlions advanced by different authorities in the scientific world to account for the apparent anomaly, bat none,

By John A. Mathews

During the prosecution of the aircraft-production program in 1917 and 1918, the writer visited many plants engaged in the manufacture of motors, planes and parts, in carrying out his duties as chairman of the Committee on Aircraft-engine Forgings. On several occasions, when the question of expansion was discussed, it was noted that there was confusion in the use of the terms: the true coefficient of expansion, a physical constant, and distortion in hardening. One engineer, referring to a steel shown in the accompanying table, stated that he could not consider it for crankshafts because of its excessive coefficient of expansion, while another steel, also Iisted in the table, was said to be especially good because it had no coefficient of expansion, since it came out of the oil bath perfectly straight. Many years ago one of our employees designed a new oil furnace; when asked what became of the products of combustion, he replied: "There ain&apos;t any, we burn them all up." While the coefficient of expansion is not without its effect in volume changes in hardened steel, it is not a determining factor in the matter of distortion and going out of shape. Irregular heating, uneven furnace bottoms, and carelessness in withdrawing the part from the furnace, as well as the manner in which the part enters the quenching bath are of greater moment. Generally speaking, also, steels of relatively low hardening temperature will distort less than those requiring higher hardening heats. The coefficient of expansion must be considered in engineering design most frequently when different metals or alloys are used in the same construction. For example, the difference of expansion between a steel crankshaft and an aluminum crank case might be of real importance and a steel with no coefficient of expansion would be much less desirable than one with the normal coefficient. About 15 years ago, the writer made many determinations of the coefficient of expansion at low temperature ranges, usually between 20&apos; and 100" C. Among the materials tested were: Pure forged electrolytic iron, 11.73 parts per million for l° C.; cast aluminum (99.93 per cent. AI.),

Jan 1, 1922

By John Mathews

DURING the prosecution of the aircraft-production program in 1917 and 1918, the writer visited many plants engaged in the manufacture of motors, planes and parts, in carrying out his duties as chairman of the Committee on Aircraft-engine Forgings. On several occasions, when the question of expansion was discussed, it was noted that there was confusion in the use of the terms: the true coefficient of expansion, a physical constant, and distortion in hardening. One engineer, referring to a steel shown in the accompanying table; stated that he could not consider it for crankshafts because of its excessive coefficient of expansion, while another steel, also listed in the table, as said to be especially good because it had no coefficient of expansion, since it came out of the oil bath perfectly straight. Many years ago one of our employees designed anew oil furnace; when asked what became of the products of combustion, he replied: "There ain&apos;t any, we burn them all up." While the coefficient of expansion is not without its effect in volume changes in hardened steel, it is not a determining factor in the matter of distortion and going out of shape. Irregular heating, uneven furnace bottoms, and carelessness in withdrawing the part from the furnace, as well as the manner in which the part enters the quenching bath are of greater moment. Generally speaking, also, steels of relatively low hardening temperature will distort less than those requiring higher hardening heats. The coefficient of expansion must be considered in engineering design most frequently when different metals or alloys are used in the same construction. For example, the difference of expansion between a steel crankshaft and an aluminum crank-case might be of real importance and a steel with no coefficient of expansion would be much less desirable than one with the normal coefficient. About 15 years ago, the writer made many determinations of the coefficient of expansion at low temperature ranges, usually between 20° and 100° C. Among the materials tested were: Pure forged electrolytic iron, 11.73 parts per million for 1° C.; cast aluminum (99.93 per cent. Al.),

Jan 2, 1920

By John A. Mathews

During the prosecution of the aircraft-production program in 1917 and 1918, the writer visited many plants engaged in the manufacture of motors, planes and parts, in carrying out his duties as chairman of the Committee on Aircraft-engine Forgings. On several occasions, when the question of expansion was discussed, it was noted that there was confusion in the use of the terms: the true coefficient of expansion, a physical constant, and distortion in hardening. One engineer, referring to a steel shown in the accompanying table, stated that he could not consider it for crankshafts because of its excessive coefficient of expansion, while another steel, also Iisted in the table, was said to be especially good because it had no coefficient of expansion, since it came out of the oil bath perfectly straight. Many years ago one of our employees designed a new oil furnace; when asked what became of the products of combustion, he replied: "There ain&apos;t any, we burn them all up." While the coefficient of expansion is not without its effect in volume changes in hardened steel, it is not a determining factor in the matter of distortion and going out of shape. Irregular heating, uneven furnace bottoms, and carelessness in withdrawing the part from the furnace, as well as the manner in which the part enters the quenching bath are of greater moment. Generally speaking, also, steels of relatively low hardening temperature will distort less than those requiring higher hardening heats. The coefficient of expansion must be considered in engineering design most frequently when different metals or alloys are used in the same construction. For example, the difference of expansion between a steel crankshaft and an aluminum crank case might be of real importance and a steel with no coefficient of expansion would be much less desirable than one with the normal coefficient. About 15 years ago, the writer made many determinations of the coefficient of expansion at low temperature ranges, usually between 20&apos; and 100" C. Among the materials tested were: Pure forged electrolytic iron, 11.73 parts per million for l° C.; cast aluminum (99.93 per cent. AI.),

Jan 1, 1922

By H. L. Luo, W. Klement

By rapidly quenching Ag-Pt alloys from the melt, a continuous series of solid solutions has been obtained. At equilibrium&apos;&apos;2 these fcc elements form a peritectic system, Fig. 1. Weighed amounts of silver and platinum powder (325 mesh, purity greater than 99.9 pct) were mixed for 24 to 120 hr, pressed into compacts, sintered at 1000°C in a hydrogen atmosphere for at least 16 hr, and then furnace-cooled. Because of the difficulty in achieving homogeneity in alloys containing more than about 40 at. pct Pt, the sintered compacts were induction-melted under hydrogen in alumina crucibles and then cold-rolled into wires. Small amounts ("30 mg) of alloys cut from various sections of the sintered compacts or rolled wires were heated to at least 50&apos; ~ above the liquidus in an alumina insert held within an induction-heated graphite crucible; then the molten alloy was ejected by a blast of helium onto a lightly polished copper strip held on the inner periphery of a rotating wheel. The flakes thus obtained were typically 1 sq mm in area or often slightly larger for the silver-rich alloys. X-ray diffraction patterns were obtained with nickel-filtered copper K radiation in a 114.6-mm-diam Debye-Scherrer camera with rotated specimens. Lattice parameters and associated uncertainties were estimated from extrapolations against the Nelson-Riley function. High-angle lines were always resolved and spacings were computed relative to r(CuKa!,) = 1.540508 The details of these techniques have been discussed previously.s&apos;6 Lattice parameters of the solid solutions are plotted in Fig. 2, together with the data of Schneider and Esch,&apos; Johansson and Linde,&apos; and Novikova and pudnitskii. Each of the present lattice spacings represents two or more independent determinations. The alloys were homogeneous within 2 at. pct of nominal composition as estimated from the uncertainties in the lattice spacings. Many of the mechanisms involved in the achievement of metastable solid solutions by rapidly quenching from the melt have been previously discussed. There is some evidence" that such solid solubility cannot be obtained when the liquid alloys are cooled

Jan 1, 1963

By H. W. Kerr, B. Soutiere

THE possibility of using unidirectionally solidified eutectic alloys as high-strength composite materials has been investigated by several workers. Unidirectionally solidified lamellar and fibrous eutectics have been shown to have good short-time structural stability at temperatures close to the eutectic melting temperature.&apos;-4 Several investigations of both short-time high temperature tensile properties and creep properties of eutectic alloys have been carried out,3-" with promising results. Little work has been reported, however, on the thermal stability of eutectic alloys which have been unidirectionally solidified and subsequently deformed in compression. Since processes such as rolling and grinding introduce compressive stresses, and since the properties depend on the spacing and perfection of the composite structure10,11 this aspect is of definite importance if unidirectionally solidified eutectic alloys are to be considered for commercial use. A Cd-Zn alloy made from 99.999 pct starting materials was cast into a graphite boat and zone levelled12 to obtain a completely lamellar structure at one end of the bar. Sections from this region of the bar were removed, recast into 6.5 mm I.D. Pyrex tubing, and solidified unidirectionally upwards at a rate of 2.8 cm per hr. Specimens were cut from the solidified rods, heated in air at 200°C (0.88 of the eutectic melting temperature) for various lengths of time, and examined metal-lographically. Compression specimens were also cut from the solidified rod carefully machined to a length of & in., and deformed with the compressive axis parallel to the original growth axis to produce a total longitudinal strain of 12 pct. Some of these specimens were examined metallographically; others were heated in air at 200°C for various lengths of time and then examined. Metallographic examination of the deformed specimens showed the two types of deformation previously described; slip lines13 (smoothly bent lamellae) and kinks13,14 (sharply bent lamellae). Very close to the specimen ends there were a large number of deformation bands, but at a distance of about -re- in. the deformation was very localized, as shown in Fig. 1.

Jan 1, 1970

By D. G. Westlake, E. S. Fisher

The habit planes for zirconium hydride precipitation in crystals of a zirconium have been determined at various hydrogen concentrations. The (10 • 0)planes are the predominant habit planes; some (10 • 5) and (10 -1) planes were observed after charging conditions which pevmitted formation of a surface layer of hydride. No platelets zrlere observed parallel to any of the twinning planes. Mechanisms for em-brittlement due to hydride precipitation are discussed. LANGERON and Lehr1 found, in 1956, that zirconium hydride precipitates in zirconium in platelets lying parallel to (10.0) slip planes. In 1960, Kunz and Bibbz reported observing the platelets in three different families of twinning planes, (10.2) {11.1), and {11.2), but never in the slip planes. The present study was undertaken to ascertain the cause of these seemingly contradictory results. EXPERIMENTAL Two specimens of iodide zirconium were used in the experiments. Specimen I was a single crystal, while specimen II contained three grains. Grain growth was accomplished by the technique of Lange-ron and Lehr. Three faces were ground on specimen I; the first was 2 deg from the (00.1) basal plane, a second was 2 deg from the (10.0) prism plane, and a third was 4 deg from the (12.0) plane. One face was ground on specimen II such that the poles of the surfaces of crystals A, B, and C were as shown in Fig. 1. After the faces were ground on 600 grit silicon carbide paper, they were chemically polished by dipping in a solution of 8 parts hydrofluoric acid, 50 parts nitric acid, and 50 parts water. This removed all cold worked metal from the surface. The samples were charged to various levels of hydrogen content by heating in hydrogen gas which had been purified by reaction with uranium powder. The various charging conditions are shown in Table I. Specimen I was heated to the reaction temperature at the indicated hydrogen pressure and allowed to react until essentially all the hydrogen was used up. Then the temperature was raised for homogenization. Specimen II was charged by making periodic addi-

Jan 1, 1962

By Martin A. Mayers

It has long been recognized that it would be highly desirable to be able to predict the temperatures at various points in a burning fuel bed and their variations with changes of the properties of the fuel and the rate of air supply. Experimenta1 investigations of fuel-bed temperature1-4 have not been lacking, but the absence of any theoretical background has made it impossible to use the results of these tests as a basis for prediction, except in a very general may. A mathematical analysis", based on a somewhat simplified theory of the distribution of lieat in a fuel bed, lias recently been completed by the author. Even though numerical values of some of the coefficients are not known, the calculations result in some conclusions of general significance. Thus, for example, it appears that when the temperatures throughout the fuel bed can be calculated, the rate at which ignition of the fuel by underfeed action can be maintained can also be calcu1ated. The uncertainty concerning the values of the coefficients referred to above is serious limitation on the use of that method. The following paper presents a discussion of these coefficients and includes estimates of their values based on the data now available. A brief description of the theory on which the analysis is based, and some results of the calculations showing their degree of agreement with experimental results, are presented by way of introduction to the discussion of the coefficients. For a more. extended discussion of the theory, see the A.S.M.E. paper5. Theory and Comparison with Experiment The theoretical analysis is similar to that used in the calculation of the stationary temperatures in a conducting solid in the classical theory of heat concluction. The fuel bed is pictured as a uniform, continuous, porous solid through the interstices of which air can be blown and ill which combustion can take place. The solid lias a finite thermal conductivity, so that heat may be transported in any direction, against the flow of air as well as in the same direction. While it is true that nothing

Jan 1, 1938

By Martin A. Mayers

It has long been recognized that it would be highly desirable to be able to predict the temperatures at various points in a burning fuel bed and their variations with changes of the properties of the fuel and the rate of air supply. Experimenta1 investigations of fuel-bed temperature1-4 have not been lacking, but the absence of any theoretical background has made it impossible to use the results of these tests as a basis for prediction, except in a very general may. A mathematical analysis", based on a somewhat simplified theory of the distribution of lieat in a fuel bed, lias recently been completed by the author. Even though numerical values of some of the coefficients are not known, the calculations result in some conclusions of general significance. Thus, for example, it appears that when the temperatures throughout the fuel bed can be calculated, the rate at which ignition of the fuel by underfeed action can be maintained can also be calcu1ated. The uncertainty concerning the values of the coefficients referred to above is serious limitation on the use of that method. The following paper presents a discussion of these coefficients and includes estimates of their values based on the data now available. A brief description of the theory on which the analysis is based, and some results of the calculations showing their degree of agreement with experimental results, are presented by way of introduction to the discussion of the coefficients. For a more. extended discussion of the theory, see the A.S.M.E. paper5. Theory and Comparison with Experiment The theoretical analysis is similar to that used in the calculation of the stationary temperatures in a conducting solid in the classical theory of heat concluction. The fuel bed is pictured as a uniform, continuous, porous solid through the interstices of which air can be blown and ill which combustion can take place. The solid lias a finite thermal conductivity, so that heat may be transported in any direction, against the flow of air as well as in the same direction. While it is true that nothing

Jan 1, 1938

By F. W. Gordon

The Whitwell firebrick hot-blast stove, for furnace use, may be seen in its three main stages of development in the accompnying drawings. Fig. 1 is the stove of 1869, the year in which it was thoroughly tested at the Consett furnaces, England; Fig. 2, the stove of 1876 and 1877, in which it was intended to reduce the cost by increasing the height; Fig. 3, the stove of 1880. Many modifications were made from time to time, generally in the direction of improvement, but the drawings illustrake the main features of progress. In the stove of 1869 the plan was to introduce the gas at A, and pass it up and down between each alternate wall, the air in the reverse direction, passing in at B. The friction in this stove was so great, owing to the restricted area of the passages and the many revervals of the gaseous current, that it was deemed imprudent to build the stoves higher than 28&apos; 6". Another reason mas that the great importance of cleaning was carefully kept in view, and it was very difficult to operate any hand scraper even to this depth. For these reasons the 22&apos; X 28½&apos; stove held the field for several yearn. A slight change made from this was to the 18&apos; X 40&apos; stove, where the height was increased, but the dumber of walls diminished. In this stove the friction was somewhat reduced, but so was the heating surface, and although it cost a little lea it was not any better. The next important change, seen in Fig. 2, was by increasing the height to GO feet and keeping the full number of walls in the stove. The heating surface and mass were much increased in proportion to the cost, and the friction decremed by alterllating over and under two or more walls, instead of one, as formerly. This stove gave admirable satisfactiou, but, although the proper doors were provided, it was very difticult to clean, owing to the long (distance the scrapers lid to traverse. Stove No. 3 is a modification of No. 2. The great question was how to decrease the cost mithotlt impairing in any yaw the

Jan 1, 1881

By F. W. Gordon

THE Whitwell firebrick hot-blast stove, for furnace use, may be seen in its three, main stages of development in the accompanying drawings. Fig. 1 is the stove of 1869, the, year in which it was thoroughly tested at the Consett furnaces, England; Fig. 2, the stove of 1876 and 1877, in which it was intended to reduce the-cost by increasing the height; Fig. 3, the stove of 1880. Many modifications were made from time to time, generally in the direction of improvement, but the drawings illustrate the main features of progress. In the stove of 1869 the plan was to introduce the gas at A, and pass it up and down. between each alternate wall, the air in the reverse direction, passing in at B. The friction in this stove was so great, owing to the. restricted area of the passages and the many reversals of the gaseous current, that it was deemed imprudent to build the stoves higher than 28&apos; 6&apos;". Another reason was that the great importance of cleaning was carefully kept in view, and it was very difficult to operate any hand scraper even to this depth. For these reasons the 22&apos; X 28 1/2&apos; stove held the field for several years. A slight change made from this was to the 18&apos; X 40&apos; stove, where the height was increased, but the number of walls diminished. In this stove the friction was somewhat reduced, but so was the heating surface, and although it cost a little less it was not any better. The next important change, seen in Fig. 2, was by increasing the height to 60 feet and keeping the full number of walls in the stove. The heating surface and mass were much increased in proportion to the cost, and the friction decreased by alternating over and under two or more walls, instead of one, as formerly. This stove gave admirable satisfaction, but; although the proper doors were provided, it was very difficult to clean, owing to the long distance the scrapers had to traverse. Stove No. 3 is a modification of No. 2. The great question was how to decrease the cost without impairing in any yaw the

Jan 1, 1881

By Emil Gathmann

(San Francisco Meeting, September, 1915) THROUGH wide experience at numerous mills in the United States I have found that there is a decided difference of opinion among the producers of steel as to what constitutes commercially sound steel. Some metallurgists insist upon having, for certain grades of steel, a so-called "open steel," -i.e., one which contains numerous blowholes of varying sizes, and consequently but little volume of true pipe, although a central intermittent shrinkage cavity often extends well down into the ingot: Such blowholes and pipe are expected to weld up during rolling or forging, because their surfaces are not oxidized. Even if this be admitted, included slag particles and a high degree of segregation are bound to be present in the product of such ingots. Blowholes are the result of an oxidized heat, and all heats, unless made or finished in the electric furnace, are oxidized more or less. Subsequent deoxidation, or rather degasification, either in the ladle or in the mold, or in both, is necessary to reduce or prevent blowholes. As is well known, a greater yield of billets or sheets is secured from the ingot by allowing the formation of blowholes, but this is undoubtedly obtained at the expense of the quality of the product. Decided segregation of carbon, phosphorus, and sulphur, as well as small included slag particles, undoubtedly exists throughout the greater portion of all so-called open steel, and cannot be removed by cropping. The first requisite for sound, homogeneous steel ingots and blooms is therefore, in my opinion, so to treat the steel in the furnace, ladle, and mold that "piping" steel is produced. The line of demarcation between harmful and so-called "harmless" blowholes is practically impossible to define. Is it not, therefore, the better and safer practice to use means for the elimination of blowholes and correspondingly reduce the segregation and allow the formation of a well-defined shrinkage cavity or pipe .at the upper end of the ingot? With the relatively cheap deoxidizers available at the present time, e.g., ferro-silicon, aluminum and titanium,

Jan 8, 1915

By W. N. Logan

WHAT is mineral wool? This question is frequently asked by those unacquainted with its manufacture. The word "mineral" suggests that it is of mineral origin; the word "wool" suggests that it is of animal origin; but the only similarities it has to wool are its fibrous character and its white fleecyness. Mineral wool is a fiber produced by melting rock to a glasslike condition and blowing the glass into fine white, wool-like threads. A -number of the products fabricated from-mineral wool are used for some form of insulation, but mineral wool is adaptable to many other uses. It is used in the manufacture-of pipe covering designed to with; stand the high temperatures produced in steam pipes. In a similar form of insulation it is used to cover boilers and furnaces. It is used in ,the fabrication of upholstery tow for sofas and car seats: In acoustics it has many uses, such as acoustifibroblock, which is used in floors to destroy sound and vibration, and acoustic mat, which is used under carpets to destroy sound. In the insulation of houses, loose wool and granulated wool are used beneath attic floors and between the studding in frame buildings to prevent the escape of heat in winter and the entrance of heat in summer. Mineral wool is used also in fabrication of linofelt, which is a quilted form of insulation; in fibrofelt, which is an insulating board; in the fabrication of lith, which is an insulating block; in anti-fibroblock ,which is used in insulation and refrigeration; in flexfelt; in loose wool; in pressed block; in heavy oiled wool; in dark oiled block; and for many other purposes. The materials used in the manufacture of mineral wool are of two kinds. The first is a rock which contains silt, clay and silica, with smaller amounts of lime and magnesia. The second is a more highly calcareous rock which may carry a small amount of magnesia. The latter is used as flux to assist in the melting of the former. The relative proportion of the alumina-iron-silica content to the lime-magnesia content is normally as fifty to fifty but a considerable range is possible.

Jan 1, 1932

By E. W. Engle

For several years the Fansteel Products Co. has been engaged in e production and development of various of the rarer metals. It is at present engaged in the commercial production of tantalum, tungsten, and molybdenum in a very high state of purity. The information contained in this paper is partly a general compilation from various sources and partly information obtained as a result of recent years of work in the laboratory of this company. Tantalum, tungsten, and molybdenum form a group peculiar to themselves among the commercially available metals. Their very high melting points (tantalum 2770&apos; C., tungsten 3350&apos; C., and molybdenum 2550" C.) set them apart so far as the metallurgical processes for their production are concerned. Further, when properly prepared and treated they will stand a somewhat unusual degree of cold work, that is work below the temperature at which marked crystal growth takes place. Such cold-worked metal may show a high tensile strength; tantalum to 130,000 lb. per sq. in., tungsten to 490,000 lb., and molybdenum to 260,000 lb., in the form of fine wire. In physical appearance, these metals are not unlike some steels; they may be better described by saying that polished tantalum somewhat resembles lead; polished tungsten, iron; and polished molybdenum, nickel. The polished surfaces of all three remain untarnished in ordinary air. Air containing corrosion-producing impurities will, in general, show molybdenum the least resistant to corrosion and tantalum the most resistant. Molybdenum has, however, a high degree of resistance to corrosion by hydrochloric acid, a property that should render it of commercial interest. On the other hand, it is markedly attacked by some of the weaker organic acids. The three metals oxidize rapidly when heated at or above a dull red in air. This feature limits their use in many applications where their high melting point and strength make them appear usable. Tungsten and molybdenum, at red heat, are quite inert to hydrogen and nitrogen; while tantalum has a rather remarkable affinity for all the ordinary gases, which results in its becoming embrittled in their presence. This

Jan 1, 1925

By S. A. Bradford

Internal-oxide precipitates in decarburized a iron alloys were studied by microscopic and X-ray methods. Diffusion of oxygen is primarily trans-granular, although large amounts of manganese or PhosPhorus cause preferred grain boundary dimsion at temperatures below 1450OF. Transgvanular internal oxidation follows the parabolic rate law with an apparent activation energy of 60 kcal per g-atom for decarburized rimmed steel and around 50 kcal per g-atom for higher alloy contents. The internal oxide is (Fe,Mn)0. Evidence was found for a miscibility gap in the FeO-MnO system. UNTIL very recently, the internal oxidation of metals was studied primarily as a scientific curiosity or, in a few cases, as a means of strengthening alloys by precipitation hardening. However, with the recent development of low-carbon enameling sheet steel, internal oxidation has become a problem of practical importance to the steel industry. For example, in 1961 it was reported1 that internal oxidation of steel can occur during decar-burization by open-coil annealing and will reduce the notch ductility of the sheet unless the process is carefully controlled. The present study was therefore undertaken to learn more about the rates and mechanism of oxygen diffusion and oxide formation in iron alloys. BACKGROUND The process of internal oxidation has been well-defined in the literature:&apos;,&apos; oxygen dissolves in an alloy, diffuses inward from the surface of the metal, and reacts to form a precipitate with the alloying element that will provide the most stable oxide. he growth of the finely divided so-called subscale, i.e., the internal-oxidation zone, depends on the diffusion rates of both the oxygen and the reactive element.4 Investigators have generally found that increasing the temperature increases the size of the oxide particles, the rate of subscale growth, and the tendency to transgranular diffusion. With very few exceptions, the square of the thickness of the internal oxide layer is directly proportional to the reaction time. Given two conditions easily satisfied for iron systems— a) an oxygen solubility much less than the concentration of the alloying metal and b) an oxygen-diffusion rate to the oxide boundary much faster than that of the alloying element—then the general expression developed by Rhines and co-workers5 for the parabolic growth rate of the internal-oxide zone can be simplified to the following form: where Co and CM are, respectively, the solubility of oxygen and the concentration of the alloying element, DO is the diffusion coefficient of oxygen, O/M is the weight ratio of oxygen to metal in the precipitated oxide, and x is the thickness of the internal-oxide zone after an annealing time t. Both the oxygen solubility and diffusion coefficient can be approximately expressed as functions of temperature by Arrhenius-type equations: in which H and Q are, respectively, the heat of solution and the activation energy of diffusion. Consequently, the apparent activation energies calculated from Arrhenius plots are the sum of the heat of solution of oxygen in iron and the activation energy for diffusion of oxygen. The data, if not the interpretation, of Schenck et al.8 bear out the fact that oxygen diffuses in the atomic form. The general rate law for atomic diffusion is: the reaction rate being proportional to the square root of the pressure at low pressures. Benard and Moreau8 studied both the surface oxidation of Fe-Ni alloys and the gradual penetration of oxygen into the metal. They observed that oxide particles first form along grain boundaries and then grow to form continuous films that eventually envelop the grains. The parabolic rate law does not usually apply in these cases, especially at the higher temperatures. The oxide formed is wustite which gradually transforms into Fe3O4 and finally into Kennedy and coauthors8 examined Fe-Ni alloys with 26, 75, and 84 pct Ni oxidized at 800°C and

Jan 1, 1964

By E. W. Davis

If the tonnage of merchantable iron ore remaining in the Lake Superior district is divided by the average of the annual shipments for the past 20 years, it will be found that this ore supply will be exhausted in approximately 35 years. This computed exhaustion period would be an indication of the future activities of the iron-mining industry if it were not for the fact that merchantable ore is being manufactured from low-grade ore, of which there is an almost inexhaustible supply in the Lake Superior district. It is true that at present only the simplest of these low-grade ores are being concentrated to any considerable extent, but progress is being made with the treatment of the more complex ores, and now, in addition to 20 washing plants on the Mesabi Range, three plants are equipped with jigs for the treatment of ore that cannot be concentrated simply by washing. The latest addition to the ore-treating plants of the Mesabi Range is a magnetic roasting and concentration plant at Cooley, Minn., in which ore that cannot be concentrated either by washing or by jigging is roasted to the magnetic state and concentrated on magnetic separators. This plant is beginning its third season of operation, and while it is too soon to make definite predictions, there are strong indications that this new process may make commercially possible the manufacture of high-grade, merchantable iron ore from large quantities of low-grade ore now considered worthless. After the iron oxide contained in an ore has been converted to magnetite, almost any desired grade of concentrate can be produced, using magnetic-concentration equipment of the types now in general use for the concentration of the natural magnetites of New York, New Jersey and Pennsylvania. The conversion of hematite (Fe203) to magnetite (Fe3O4) is easily accomplished by heating the ore to a dull red temperature in a reducing atmosphere. The reaction is slightly endothermic, and while it requires 200 B.t.u. to heat to 900&apos; F. one pound of hematite ore containing 45 per cent Fe, it requires only 100 B.t.u. to convert the oxide into magnetite. In the laboratory, using small quantities of ore, this conversion is very simple, but large furnaces suitable for commercial

Jan 1, 1939

By E. W. Davis

IF the tonnage of merchantable iron ore remaining in the Lake Superior district is divided by the average of the annual shipments for the past 20 years, it will be found that this ore supply will be exhausted in approximately 35 years. This computed exhaustion period would be an indication of the future activities of the iron-mining industry if it were not for the fact that merchantable ore is being manufactured from low-grade ore, of which there is an almost inexhaustible supply in the Lake Superior district. It is true that at present only the simplest of these low-grade ores are being concentrated to any considerable extent, but progress is being made with the treatment of the more complex ores, and now, in addition to 20 washing plants on the Mesabi Range, three plants are equipped with jigs for the treatment of ore that cannot be concentrated simply by washing. The latest addition to the ore-treating plants of the Mesabi Range is a magnetic roasting and concentration plant at Cooley, Minn., in which ore that cannot be concentrated either by washing or by jigging is roasted to the magnetic state and concentrated on magnetic separators. This plant is beginning its third season of operation, and while it is too soon to make definite predictions, there are strong indica-tions that this new process may make commercially possible the manu-facture of high-grade, merchantable iron ore from large quantities of low-grade ore now considered worthless. After the iron oxide contained in an ore has been converted to mag-netite, almost any desired grade of concentrate can be produced, using magnetic-concentration equipment of the types now in general use for the concentration of the natural magnetites of New York, New Jersey and Pennsylvania. The conversion of hematite (Fe203) to magnetite (Fe304) is easily accomplished by heating the ore to a dull red tempera-ture in a reducing atmosphere. The reaction is slightly endothermic, and while it requires 200 B.t.u. to heat to 900° F. one pound of hematite ore containing 45 per cent Fe, it requires only 100 B.t.u. to convert the oxide into magnetite. In the laboratory, using small quantities of ore, this conversion is very simple, but large furnaces suitable for commercial

Jan 1, 1936