Search Documents

Canadian owned Lake are carriers will be used again this year in an attempt to make up the deficit caused by the two months steel-strike. Buffalo mills need between 5 million and 6 million tons of ore before the Lakes navigation season ends. Mutual Security Program aid will help reactivate Austria's largest iron ore mine. The Erzberg development is one of the moat important in Europe. MSA announced approval of $500,000 in supplemental financing of equipment. Following the war, the Russians stripped the Erzberg and Radmar deposits of equipment. The he Carborundum Corp. is going to build a $2.44 million plant at Akron, NO.. TOP near Niagara Falls for production of rare metals used by the Atomic Energy Commission. A subsidiary, the Carborundum Metals Co., Inc.,, will produce zirconium, hafnium sponge metals. The pyrochlore rich Sukulu Hills in Eastern Uganda will be mined under a pool arrangement including Tinto Mines, Monsanto Chemicals and Frobisher Mines. The combine will be known as the Uganda Development Corp., Pyrochlore is used in the manufacture of heat-resisting. alloys for Jet engines.

Jan 1, 1952

By J. W. Halley

COPPER has frequently been recommended as an alloying element for steel and the precipitation-hardening of steels containing from 1 to 2 per cent copper has been studied by a number of investigators. The straight copper steels, however, have not been used extensively and little advantage has been taken of the precipitation-hardening of complex steels containing appreciable amounts of copper. It is diffi-cult to produce a satisfactory surface on the straight copper steels and undoubtedly this has discouraged their use. During recent years a number of steels containing enough copper to make them susceptible to precipitation-hardening have been put on the market. These steels belong to the group usually referred to as "low-alloy high-tensile" steels. They were designed for use in the "hot-rolled" condition; transportation equipment and large structures that cannot be readily heat-treated have been their chief application. Little emphasis has been placed on the possibility of strengthening those containing substantial amounts of copper by precipitation-hardening. The present investigation was undertaken to determine the precipitation-hardening characteristic of one of the "low-alloy steels."

Jan 1, 1940

By E. Buehler

THE floating zone refining technique'-4 has provided a new experimental approach to the purification of many reactive materials especially those with high melting points. The method avoids the use of a crucible and at the same time it provides a favorable environment at the freezing interface for the growth of single crystals. The physical properties of refractory metals such as molybdenum and tungsten have long been of interest from a fundamental point of view and because of their widespread use in vacuum electronics. Single crystals are often desirable for study. Prior to the introduction of zone melting, single crystals of these metals were usually grown in the solid state at temperatures slightly below the melting point by strain annealing3 or by the application of a moving temperature gradient. Such techniques were mostly successful on wires, ribbons, or rods having small cross-sectional areas. Recently, larger samples of tungsten, molydbenum, tantalum, columbium, and rhenium were melted by a floating zone process which employed electron bombardment heating.10 Single crystals were obtained in many instances

Jan 1, 1959

By Zay Jeffries

THE object of the present paper is to enlarge somewhat on the general principles advanced in my discussion 1 of Mathewson and Phillips' article on. The Recrystallization of Cold-Worked Alpha Brass on Annealing.2 It will also serve as an acknowledgment of Prof. Howe's3 most important remarks on my contribution. In this paper the writer has adopted Prof. Howe's suggestion to substitute the term "germinative temperature" for "critical temperature for grain growth." Instead of being an exact or certain temperature it should be considered that the germinative temperature phenomenon exists throughout a small temperature range. Factors Influencing Fast Growth Phenomena The development of grains of macroscopic size at the germinative temperature should be considered the extreme condition of a general rule. When considered in this light it is not strange that the development of these large grains should be the exception and not the rule. The principal factors influencing the operation of the laws of fast growth temperature are as follows: 1. Rate of heating.

Jan 10, 1916

By R. G. Robins, O. J. Kwok

The application of chemical thermodynamic theory to high temperature aqueous systems is discussed as a basis for the explanation of thermal precipitation. The derivation of high temperature potential/ pH diagrams is briefly outlined in order to show a temperature/pH relationship for hydrolytic precipitation, which is an effect that is caused simply by heating an aqueous solution. Various examples of thermal precipitation are given, with particular reference to separation of metal values from leach solutions. Metal sulphate solutions are shown to precipitate basic sulphates, hydrated sulphates , oxides, hydroxides, and oxydroxides of the metal depending largely on the pH, the concentration of metal ion, and the concentration of sulphate or bisulphate. The CuS04-H2S04-H20 system is treated in some detail, and the separation of copper from other metal ions is investigated. Other separations involving Fe, Ni, Zn, Cd, and Cr are considered. Other advantages of thermal precipitation, such as the formation of high purity, large particle size and easily filterable materials, are presented. The kinetics of thermal precipitation are also briefly examined.

Jan 1, 1973

By John D. Sullivan

ALUMINUM and magnesium plants in the United States underwent enormous wartime expansion which made many wonder if ghost plants would result when industry swung back to a peacetime basis. Production capacity of primary aluminum ingots was stepped up from 150,000 tons annually to about 1,150,000 tons; magnesium production increased from 2500 tons in 1936 to nearly 200,000 in 1943, with a production capacity of some 300,000 tons. Not only was primary metal production enlarged but also the capacity of prime fabrications such as castings, forgings, extrusions, and sheets was correspondingly increased. In mid-December it was estimated that production of primary aluminum ingots in the United States in 1946 will be about 410,000 tons while consumption will be about 500,000, close to half of the wartime consumption. The 1946 estimated consumption of secondary aluminum is 200,000 tons. The critical shortage of soda ash is hindering production of primary metal, and the outlook for an early relief of this shortage is dark.

Jan 1, 1947

By D. T. Peters, S. Floreen

The age hardening behavior of an Fe-8Ni-13Mo alloy was studied after the matrix had been varied to produce either ferrite, cold u~orked ferrite, or nzassive nzartensite. The aging behavior of the cold worked ferrite and murtensite structures were very similar. The martensite aging kinetics were much different from those observed in earlier studies of aging of maraging steels, even though the martensite wzatri.r had the same dislocation structure as those found in maraging steels. The results suggest that the previously observed precipitation kinetics of maraging steels ?nay have been controlled by the nucleation be-haviov, which in turn were dictated by the alloy compositions and the resultant identities of the precipitating phases. IT is well known that the rate of precipitation from solid solution depends not only on the degree of super-saturation, but also on the density and distribution of dislocations in the matrix structure. These imperfections often act as nucleation sites, and may also enhance atomic mobility. 'Thus, the presence of dislocations is important since the type and distribution of precipitates may be determined by them. The precipitate density and morphology in turn affects the mechanical properties of the alloy. A number of studies have been devoted to the precipitation characteristics in various types of maraging steels.'-" These are iron-base alloys containing 10 to 25 pct Ni along with other substitutional elements such as Mo, Ti, Al, and so forth, that are used to produce age hardening. The carbon contents of these steels are quite low, and carbide precipitation is not believed to play any significant role in the aging reactions. After solution annealing and cooling these alloys generally transfclrm to a bcc lath or massive martensite structure characterized by elongated martensite platelets that are separated from each other by low angle boundaries, and that contain a very high dislocation den~it~.~~~~~~~~-~~ Age hardening is then conducted at temperatures on the order of 800" to 1000°F to produce substitutional element precipitation within the massive martensite matrix. Most of the aging studies to date have revealed several common traits in these alloys, regardless of the particular identity of the precipitation elements. Generally hardening has been found to be extremely rapid, with incubation times that approach zero. The agng kinetics, at least up to the time when reversion of the martensite matrix to austenite begins to predominate, frequently follow a AX/~~ = ktn type law, where x is hardness or electrical resistivity, t is the time, and k and n are constants. The values of n are frequently on the order of 0.2 to 0.5, which are well below the idealized values of n based on diffusion controlled precipitate growth models. Finally, the observed activation energy values are typically on the order of 30 kcal per mole, and thus are well below the nominal value of about 60 kcal per mole found for substitutional element diffusion in ferrite. The common explanation of these observations is that the precipitation kinetics are controlled by the massive martensite matrix structure. Thus, the absence of any noticeable incubation time has been attributed, after ~ahn," to the fact that the precipitate nucleation on dislocations may occur without a finite activation energy barrier. The low values of the activation energy are generally assumed to be due to enhanced diffusivity in the highly faulted structure. If this explanation that the precipitation kinetics are dominated by the matrix structure is correct then one should observe a distinct difference in lunetics between aging in a martensitic matrix and aging the same alloy when it has a ferritic matrix. Such a comparison cannot be made with conventional maraging compositions, but could be made with the alloy used in the present study. In addition, the ferritic structure of the present alloy could be cold worked to produce a high dislocation density so that one could determine whether ferrite in this condition would age similarly to martensite. EXPERIMENTAL PROCEDURE The composition of the alloy used in this study was 8.1 pct Ni, 13.0 pct Mo, 0.10 pct Al, 0.13 pct Ti, 0.012 pct C, bal Fe. The alloy was prepared as a 40 lb vacuum induction melt. The heat was homogenized and hot forged at 2100°F to 2 by 2 in. bar, and then hot rolled at 1900°F to $ in. bar stock. The aging lunetics were followed by Rockwell C hardness and electrical resistivity measurements. Samples for hardness testing were prepared as small strips approximately 2 by $ by 4 in. thick. Electrical resistivity was studied on cylindrical samples approximately 2 in. long by 0.1 in. diam. The method for making the alloy either martensitic or ferritic was based on the fact that the alloy showed a closed y loop type of phase diagram. At high temperatures, above approximately 24003F, the alloy was entirely ferritic. Small samples on the order of the dimensions described above remained entirely ferritic after iced-brine quenching from this temperature. In practice, a heat treatment of 1 hr in an inert atmosphere at 2500°F followed by water quenching was used to produce the ferritic microstructure. These samples were quite coarse grained and usually en-

Jan 1, 1970

By William Glenn

Almost beyond doubt, the most important contribution to the assaying of copper yet made, is that of Mr. Eustis (Bans., xi., 120) on the " Comparison of Various Methods of Copper Analysis," which indicates in a manner for which the assayer cannot but feel grateful, how a copper sample ought to be treated from the moment it enters the laboratory until the copper is finally weighed. Admitting, as the present writer is inclined to do, that this paper establishes, as the official standard, the method of electrolysis, we may note as one of the few details which it does not finally fix, the kind of battery most desirable for precipitating the copper upon platinum. In this respect each assayer appears to be a law unto himself, while all feel more or less " shaky " as to the results. Classsen seems to suggest a remedy when he directs the measuring of the -gases liberated by the battery employed. But, in fact, that measure is not a constant in the Bunsen elements which he prescribes for copper determination. Furthermore, measuring gases necessitates more machinery and labor than the average assayer has a stomach for. It is, however, but just to Classen, to whom we owe so much, to reeall that he wrote more especially for students in the schools.

Jan 1, 1889

ON presenting the medalist, J.. V. W. Reynders said, in part: "Far the greatest progress in the art of steel-nuking has occurred in the production of lighter forms such as tool steels and steels entering into the moving parts of machinery generally, and particularly into the con-struction of automobiles and airplanes. In this highly specialized field in which the study of alloys and heat treatment has brought about such fundamental changes of design and practice, Dr. Mathews has achieved a ranking position. "As the technical head of the largest producer of special steels, his laboratory conclusions are frequently but a few steps removed from practical exploitation. The experimental determinations of yesterday must be sufficiently conclusive to form the basis for the specific plans of today, and to warrant commercial production tomorrow. His is not the complacent atmosphere of theoretical speculation, but one in which practice fol-lows close upon the heels of scientific research.

Jan 3, 1928

We would like to thank Mr. Mandolesi for his informative paper on rails from strand cast steel. The chemical and structural properties of the strand cast steel were of particular interest to us. We would like to supplement his excellent report with some of Inland's findings from our Caster with submerged nozzles and strands reduced in line from 7" x 7" to 5-5/8" square cross section. Inland has conducted extensive segregation studies on AISI 1049 steel - Fine Grain 0.50% carbon and 0.75% manganese. Based on approximately 80 heats, our normal segregation pattern results in analyses of .49% carbon in the center, and 0.50% carbon at the midway and edge position. The sulfur analysis averages .025% in the center, .027% midway, and .026% at the edge. Note the slight negative segregation between the center and midway position. This steel, being lower carbon and probably cast nearer the liquidus, resulted in less segregation than the 0.80% carbon rail steel.

Jan 1, 1972

By B. K. Parekh, W. M. Goldberger

Silicon carbide (Sic), produced by heating rice hulls to elevated temperatures, contains a mixture of beta crystalline silicon carbide whiskers, particles, and unreacted carbon. The silicon carbide whiskers are 0.5 micron in diameter and 50 to 100 microns in length and have been found useful for reinforcing metal and other composite materials. The carbon can be removed by combustion, but this makes separation of the silicon carbide whiskers from particles difficult and a high grade whisker product cannot be made. However, a clean, high grade SiC whisker product can be obtained from the pre-burned converted rice hulls using physical separation processes that are based on differential wetting. Recovery of Sic whiskers from the pre-burned material was found to exceed 90%. A modification of the froth flotation process developed during this study is now being used commercially to separate silicon carbide whiskers and particles and to recover a high grade whisker product.

Jan 1, 1986

By Saburo Shigeno, Kunzo Amano

As shafts and tunnels move deeper levels in underground mining, development planning becomes more complex. The most serious problem is the aggravation of environmental conditions due to the imposition of higher-than-natural temperatures upon exposed strata. Since such a problem is a potential hazard to health, safety, and production, the authors have developed a system of computer-derived ambient-air temperature data for every major point of an underground mine under a given set of conditions. This system is comprised of two subsystems: 1) Ventilation network analysis, 2) Estimation of air - current temperature. The former is based on the Hiramatsu-Oka method, an improvement of the Scott-Hinsley method. The Hiramatsu-Oka method allows fast convergence and consideration of various fan characteristics. The latter subsystem considers heat radiation from strata, and the humidity. In several tests conducted at Besshi and Sazare Mines of Japan, the computer-derived data correlated with actual conditions.

Jan 1, 1969

By L. E. Paulson

INTRODUCTION The Northern Great Plains has 16 billion tons of strippable lignite (1). Presently, 15 million tons per year are mined; essentially all is used for generation of electrical power. In the future, additional large quantities will be consumed in the production of gaseous and liquid fuels. A major consideration in design and operability of power stations and conversion plants is the nature of the ash or inorganic constituents of the lignite used. These inorganic components cause fireside fouling in boilers, exert a catalytic effect in liquefaction and gasification, and contribute to particulate and SO2 emissions. Ash fouling on fireside boiler tubes cause reduced heat transfer and gas flow which limits boiler performance. Severe fouling can result in shutdown of the boiler. A comprehensive test program in both pilot plant and field studies at the Grand Forks Energy Technology Center (GFETC) has shown that ash fouling increases with increased sodium content of low-rank coals (2). The sodium in the coal can be

Jan 1, 1983

By L. L. Wyman

SINCE the observations of Heyn,1 relative to the embrittlement of copper after having been heated in hydrogen, this subject has received considerable attention from later investigators. The published works of Archbutt2 and of Bengough and Hill3 give the reasons for this embrittlement-the formation of steam by the reaction between cuprous oxide and hydrogen. From Ruder,4 Pilling,5 Moore and Beckinsdale,6 Bassett and Bradley,7 and from Smith8 can be obtained quantitative data concerning the action of hydrogen and other reducing gases on copper samples having various oxygen contents. This problem has been discussed from a practical standpoint by Fuller9 who calls attention to some of the instances of this embrittlement encountered in the manufacturing field. The examples he cites may be considered typical cases of copper embrittlement which were incident to the process of manufacture. In many cases, such difficulties are overcome by changes in the manufacturing process.

Jan 1, 1931

By R. S. Archer

THE binary aluminum-silicon alloys have certain characteristic advantages which are now well known, and these alloys have come into considerable use during the past several years.1 Their field of application has been limited to a certain extent, however, by their low yield point and hardness, low endurance limit, and relatively poor machining characteristics. These properties are improved by the addition of copper, and the ternary aluminum-silicon-copper alloys constitute an important class. The addition of copper decreases the corrosion resistance of the aluminum-silicon alloys and increases specific gravity. Magnesium is a hardening addition which seems to have relatively little effect on corrosion resistance, and which, of course, reduces specific gravity. The object of the work described in this paper was the development of alloys and heat treatments for the production of sand castings and permanent-mold castings having substantially all the advantages of the binary aluminum-silicon alloys together with mechanical properties improved to a degree permitting wider application.

Jan 1, 1930

By F. F. ESPIE

Giving the keynote address in the final session of a conference dealing with closely related topics has a disadvantage in that much of what can be said has been said. It also has an advantage, however, because it presents the speaker with the opportunity to integrate and analyse the material presented by the various speakers. I would like to look to the near future in Australia and the United States of America, to the risks, problem areas, and changes of a rapidly evolving post-industrial era-an era we are beginning to experience where industry no longer 'calls the tune'. We miners have been quick to point out and emphasize, that ours is a 'high-risk' industry in the world of business and commerce. Yet, clearly those who have survived, and been successful, have learned to anticipate and cope with risk and change. This ability has been a 'distinguishing feature of the industry's leaders who, in market studies and commodity selection, exploration and development, mine planning, metallurgical pro- cessing, and general administration and operation 1. identify areas-of risk or inevitable change, 2. analyse, test and quantify those factors of risk or change, and 3. design methods, systems, equipment to eliminate, moderate, or control or economically compensate for predicted risks or changes.

Jan 1, 1978

By FRANK R. VAN

I. INTRODUCTION. IN the summer of 1908, R. B. Cochran, Superintendent of the Compania Metalurgica Mexicana at Sierra Mojada, Mexico, presented to the Department of Geology and Mineralogy at Case School of Applied Science an interesting series of silver-, copper-, and lead-ores from the Veta Rica mine. These ores contained several interesting minerals which were associated in a somewhat peculiar manner, so that I was impelled to make a closer study of their occurrence. The investigation has brought out several new facts concerning the geology of the district and the geological occurrence of the ores, and therefore has seemed worthy of record. Two papers have been published previously about the region, one by Chism1 in 1887, and the other by Malcolmson2 in 1902. These articles, however, treat of the district more from the stand-point of the metallurgist and mining engineer, and not much attention is devoted to its mineralogy and economic geology. II. GEOGRAPHICAL LOCATION OF THE DISTRICT. The Sierra Mojada is situated in the extreme western part of the State of Coahuila, near the Chihuahua boundary. It is reached best via the Mexican Central railroad from El Paso, Tex., to Escalon, Chihuahua, a distance of 494 miles. From this point, a branch line, the Mexican Northern railroad, runs 78 miles in a NE. direction to the mines, which are its northern terminus. The railroad was built about 1890, practically on account of the Sierra Mojada mining-district. 1 Sierra Mojada, Mexico, by Richard E. Chism, Trans., xv., 542 (1886-87). 2 The Sierra Mojada, Coahuila, Mexico, and Its Ore-Deposits, by James W. Malcomson, Tram., xxxii., 100 (1901).

Aug 1, 1912

By B. G. Klugh

(New York Meeting, February, 1913.) THE present paper represents a preliminary investigation of the ultimate structure of iron-bearing materials which have been subjected to heat treatment for the purpose of agglormer-ating the fines, or for chemical changes, or for both. Primarily, the object of this inquiry was to determine the relation of the microstructure of each of these materials-to its specific susceptibility to the action in the blast-furnace. It is hoped that this small contribution will serve as a nucleus to a line of research that will throw some light upon the debated questions involved in blast-roasting. Thus far the investigation has been conducted along lines of analogy of known principles, rather than through the applica-tion of any well-defined system of microscopic petrography. This is obviously due to the fact that we are dealing with materials which are the artificial products of a new art, rather than with the natural materials from which the essence of the pure science has been evolved. In the limited tune allowed for this research, it has been conducted upon those materials the chemical content of which allows of their use commercially in the blast-furnace.

Jan 5, 1913

By F. R. Hensel

Up to the present time few attempts have been made to produce hard nonmagnetic materials by heat treatment of austenitic steels. The usual result has been to cause them to pass into the martensitic stage, thus destroying to a great extent the typical austenitic properties, since this involves a transition of a portion of the iron from a face-centered to a body-centered type of atomic arrangement. High-strength nonmagnetic materials such as might be provided by properly hardening austenite are required in the electrical industry for different machine parts. In Europe nonmagnetic retainer rings for restraining the end-turns of the rotor windings in turbo-alternators have been developed as a special application of high-strength austenite. In testing1 a 28,000-kva. three-phase Siemens turbo generator running at 3000 r.p.m. at full load current, the losses in the short-circuit test were 450 kw. for the magnetic ring and 286 kw. for the nonmagnetic, and the difference should be attributable to the magnetic ring. The differences in temperatures during the same test are given in Table 1 and these show the advantage of a nonmagnetic over a magnetic retainer ring.

Jan 1, 1931

By John Fulton

The Menominee range is one of the four great mining belts that flank the western prongs of Lake Superior. It has received its name from its location along the north side of the Menominee river, which at this place flows between the States of Michigan and Wisconsin. The term "range" is derived from the elevated ridge, extending in a westward direction, and along the southern flank of which the iron-ore mines are located. This range is some 200 to 300 feet high above the general level of the adjacent country, and is made prominent by its surroundings of low, swampy lands. Its whole length is about 27 miles, and it is intersected, at intervals along its course, by gaps which are threaded by streams. The geology of the Menominee range is peculiarly interesting. It is composed of three distinct groups of Hurouian rocks. The supporting group consists of light-colored limestone beds of a crystalline, siliceous character, called the "Norway limestone belt." The map, Fig. 1, and the section, Fig. 2, will give a general notion of the position and structure of the range. The properties shaded in the map are those of the Penn Iron Mining Company, which is the Michigan representative of the Cambria Iron Company of Johnstown, Pennsylvania. This belt is at least 1200 feet thick. It outcrops boldly at many localities along the range, especially north of the Norway, Quinnesec and Chapin mines. At Quinnesec it can be studied readily. The next, or Banking group, which is estimated at a thickness of 1000 feet, is called the Quinnesec ore-formation. It consists, in the portion next to the limestone, of siliceons or jasper slates, largely impregnated with iron oxide. These are succeeded by argillaceous hydro-mica black and flesh-colored slates. This formation embraces the deposits of the iron-ores. The third group consists of a series of dark gray, slaty or schistose beds, with occasional quartzose bands, having a thickness of 2000 feet. It is called the Lake Hanbury slate group.

Jan 1, 1888