Search Documents

By John R. Lewis

DURING the past few years there has been considerable interest in the sizing and the preparation of the iron ore fed into blast furnaces. Furnacemen know that proper sizing of ore tends to increase the efficiency of the furnace. It has been shown by Joseph1 and his associates that there is a direct relationship between the porosity of an ore particle and the time required for its reduction in the blast furnace. This relationship may be stated as follows: All other factors remaining constant, the time for reduction of a given sample of ore is inversely proportional to its porosity. As a consequence, large pieces of very porous ore, say 3 or 4 in. in cross section, will be completely reduced by the time they reach the hot zone just above the tuyeres, while large pieces of dense, nonporous ore may reach the hot zone with their centers unreduced. This means that for the latter complete reduction will be accomplished by the so-called "direct method;" i.e., where carbon reacts directly with the ore. Some recent work by Philbrook2 seems to contradict this rule. He found that of two unlike ores he studied, the one with the lower porosity reduced more readily. He explained his results as "possibly due to an apparently greater tendency of the `A' ore (lower porosity) to crack during preliminary dehydration and during reduction." This brings his results in line with the rule stated above. It is not the author's intention to enter into a discussion of the merits of "direct" versus "indirect" reduction. It is enough to say that, in general, indirect reduction is desirable. For the greatest efficiency, Gruner's theorem3 requires that all reduction in the blast furnace be indirect. Joseph seems to believe this also, because in his recent article on Some Comparisons between Iron Ore, Sinter and Nodules as Blast Furnace Feed' he concludes that: "In general, the carbon in blast-furnace coke is used most efficiently when the largest amount of the carbon charged reaches the tuyeres." However, P. V. Martin,' in an excellent paper, has shown that some direct reduction may actually increase the efficiency of the furnace; that is, increase its rate of production while maintaining maximum fuel economy. For nonporous ores there is more opportunity to have an excess of direct reduction unless the factors that make for indirect reduction are favored; for instance; the proper sizing of the ore particles. Another factor that has an important bearing on the reduction rate, as it is affected by particle size, is the flow of heat into the particle. The ore particle

Jan 1, 1947

The engineering personnel shortage, present and impending, so well brought out in the article in Mining Engineering in the August, 1951 number, both in the editorial lead and the article by William B. Plank and Henry J. Petrie, has left untapped and has ignored a potential source of supply that would fill the need ably and with complete satisfaction. This source is comprised of the women engineers- and geologists, both presently, trained and able to handle work at all levels, and the many who would make splendid engineers and geologists if they could hope for even a modest taste of the square deal that should be theirs, but, as we all know, is not. I write from experience. It is not pleasant or sensible to have to urge borderline cases among men students to consider engineering and geology as careers to fill the need, when I have far more able, interested and suited young women students whom I must divert into other channels. It does not make sense to scrape the bottom and sides of the barrel to induce potentially second or third rate male engineers and geologists to enter the profession when we have superior material among the women, eager to do good work in these fields. It does not make sense for these men to become second or third rate in these fields when they might be first rate salesmen, musicians, advertising copywriters or policemen. Nor does it make any more sense to force potentially first rate female geologists and engineers to become second or third rate and very frustrated typists, kindergarten teachers, dress sales-women or clerks. At this point I am willing to admit that where superstitious -miners object to women in underground workings, men are available for the jobs. Moreover, it is not necessary for women to be sent into the most difficult country, if there is reluctance on either side of the contract. There may be fewer of them eager for the roughest assignments, in proportion to the men, but women are so accustomed to discrimination far more complete than that against any racial or religious group, that a reasonably tough assignment would seem like a heaven-descended joy. In my own experience, I have found that my girl students majoring in geology, could keep up with me in the field in the roughest terrain, but. the men, all but the best students and the most physically fit young men, complained that they could not keep up with me and that I always "walked their-legs off. The women, a few men and I always returned with bags heavy with well chosen specimens and proper notes. Most of the men carried no specimens and-but poor scraps of notes on loose bits of paper. Yet the men were urged to prepare for a career in engineering or geology if their examination marks were reasonably good. When we find that we still have a shortage of engineers and geologists, after putting all the qualified women to work, then we may begin to worry. Until then, we are simply fooling ourselves as we wander in, a forest of outmoded tradition and emotional habit reactions. MARY W. GARRETSON ASSOC. MEMBER, AIME SCARSDALE, N. Y.

Jan 1, 1952

By Charles L. Guettel

The temperature coefficients of electrical resistance of 31 alloys in the nickel-rich corner of the Ni-Cr-Fe system were determined. The results indicate that a range of binary Ni-Cr alloys has lower temperature coefficients than a specific region of Ni-Cr-Fe alloys which has been reported and quoted by others as providing the lowest coefficients in the ternary system. DESIRABLE properties of resistivity and temperature coefficients of resistance have been the basis for the successful commercial application of various Ni-Cr and Ni-Cr-Fe alloys. In particular, low or negligible temperature coefficients of resistance are necessary for wire used in precision wire wound resistors and potentiometers involved in closely controlled electrical and electronic circuitry. Alloys most successfully applied to this purpose basically have not been ternary Ni-Cr-Fe alloys but rather heat-treated Ni-Cr alloys in the region of approximately 73 to 79 pct Ni and 20 pct Cr with significant additions of other elements such as aluminum, silicon, iron, copper, manganese, and cobalt. While the addition elements play a vital role in the nature and control of the temperature-resistance curve of any one of these alloys, the inherent relatively low temperature coefficient of the binary Ni-Cr base composition itself in the approximate region of 80 pct Ni and 20 pct Cr contributes fundamentally to the eventual negligible temperature coefficient obtained with the applied alloys. W. A. Dean 1 has reported mean temperature coefficients (20' to 100oC) of as-cast samples for the Ni-Cr-Fe system, the nickel corner of which is given in Fig. 1. Dean had to use as-cast samples because alloys from a considerable region of the system were unworkable. Dean refers to the work of Hunter and sebast2 who used annealed wire samples to show that, for chromium contents of 10 to 25 pct, the temperature coefficient increases as the iron content is increased at the expense of nickel. Although the data of Hunter and Sebast were limited in the nickel-rich areas to eight samples of 60 to 91 pct Ni with only four samples containing iron, the possibility that no Ni-Cr-Fe alloy has a lower temperature coefficient than certain binary Ni-Cr alloys should have been given serious consideration. However, Dean's work has been referred to by J. S. Marsh,3 who, quoting Dean, states that for the temperature coefficients "the smallest values-about 0.0001 per oC (100 ppm)—were found for alloys containing about 55 pct Ni and 20 pct Cr" (balance iron). A region such as that reported by Dean would be significant to those trying to develop alloys for the applications described. Therefore, a series of three-pound laboratory open-air induction melts of Ni-Cr and Ni-Cr-Fe alloys were melted, conventionally processed to 0.005 in. diam wire, and continuously strand annealed at 1900° F. The basic Ni-Cr compositions, with balances essentially iron other than usual minor impurities, and the corresponding temperature coefficients of resistance and resistivities are given in Table I. The resistivities are approximate and are not to be considered as a basis for relating them to their position of composition in the ternary system. The wire diameters were determined with a micrometer, and not by weight and density measurements which would be required for accurate resistivity values. However,

Jan 1, 1963

By Walter B. M. Davidson

Phosphorus is one of the elements having the widest distribu tion, and phosphoric acid plays an important part in the composition of the crust of the earth. It is allied in various chemical combina- tions with many bases, of which lime, alumina and iron are the most common. It is difficult to state in what chemical combination phosphoric acid predominates in the crust of the earth, for while phosphate of lime, as the mineral which is sought for and found in deposits of economic value is the most familiar, it is probable that the phosphates of alumina and iron are the most usual forms in which phosphoric acid exists in all soils not essentially calcareous. It has been shown by thousands of analyses that all fertile soils contain from a trace to 0.5 per cent. of phosphoric acid. All limestones, dolomites and chalks contain it in proportions which, though usually small, are large enough to make careful analysis necessary in the selection of limestone as flux for iron-smelting. It is generally Trenton limestones that are found best for this purpose, the more recent strata being more phosphatic. In some places phosphoric acid replaces carbonic acid, and the limestone or chalk becomes phos phatic to a large degree, or sometimes pure phosphate of lime. The waters of the ocean, from very early periods, have contained phosphoric acid. Different analyses show varying contents; it is asserted that some portions of the Gulf Stream are more phos phatic than the surrounding waters of the Atlantic. Many springs, usually from limestone regions, contain soluble phosphates in vary ing quantities. I think it safe to assert that phosphorus is nearly the most widely and evenly distributed element on the surface of the earth, and probably the most subdivided. This can be readily understood when the important part which phosphoric acid plays and has played in the vital cosmos is taken into consideration. Phosphorus was on the earth in gaseous, liquid or solid form before the dawn of life, and since then all animal and vegetable creation have combined with the

Jan 1, 1893

By O. D. Gonzalez, H. A. Wriedt

Alloys ranging from pure iron to pure nickel were saturated with nitrogen gas at 918°, 999°, and 1217°C and analyzed. The solubility of nitrogen at 1-atm pressure was obtained as a function of nickel content for the whole range of iron-nickel alloys and the temperature dependence of solubility is shown for the experimental alloy compositions. The heat of solution and the entropy of solution of nitrogen in the alloys as func-tiom of composition up to 41 pct Ni are given. 1 HE acquisition of more exact thermodynamic information for systems composed of iron with various alloying elements continues to interest ferrous metallurgists. The interstitial alloying elements, especially carbon, hydrogen, and nitrogen, comprise a field of particularly intense study. A recent investigation of carbon solubility in Fe-Ni alloys held at 1000°C in gases of fixed carbon activity showed an unpredicted minimum in the solubility near 72 pct Ni.1 The present investigation was undertaken to see if a similar anomaly in solubility existed for nitrogen in Fe-Ni alloys. The solubility of nitrogen in ? iron at known nitrogen activities has been measured several times.&apos;-&apos; Corresponding information for the solubility of nitrogen in solid Ni and Fe-Ni alloys is not available. Juza and sachsze9 reported that metallic nickel dissolved 0.07 pct N in equilibrium with Ni3N at 445°C. This result was regarded as dubious by Turkdogan and Ignatowicz10 who found less than 0.0004 pct N in nickel specimens equilibrated at 600°C with ammonia-hydrogen mixtures having fugacities of N2 gas up to 35,000 atm. Such fragmentary reports indicate only that nitrogen gas has a very much lower solubility in nickel than in iron. MATERIALS A purified iron from Battelle Memorial Institute was used for solubility measurements. This grade contained more than 99.95 pct Fe, the highest content of any measured individual impurity being 50 ppm for each of As, C, Cu, and Pb. The nickel and iron-nickel alloys, supplied by the International Nickel Co., contained 0.02 to 0.04 pct C, 0.17 to 0.19 pct Mn, 0.04 to 0.08 pct Si, < 0.01 pct P, <0.03 pct S, and <0.20 pct Co as principal impurities. The Fe-0.59 pct Mn alloy was of zone-melted quality, the highest concentration of any individual impurity being 15 ppm Al. The "prepurified" grade of nitrogen gas from Matheson Co. had a nominal nitrogen content of 99.996 pct. An "electrolytic" grade of hydrogen gas from National Cylinder Gas. CO. in which the principal impurity is water vapor was admixed with the nitrogen to prevent oxidation of these specimens. This grade was preferred to a purer grade because the presence of some oxygen helps in suppressing contamination of the specimens, for instance, by silicon from the porcelain furnace tube. EXPERIMENTAL PROCEDURE The specimens were equilibrated in vertical tube furnaces through which a 99 pct N2-1 pct H2 gas was passed at ambient pressure. For the 915", 918", and 999°C runs, a wound-resistance furnace was used, and for the 1217°C runs, a furnace with a tubular silicon carbide element was used. The temperature control system on both furnaces was similar: a Weston "Celectray" controller with a modulator, responding to the electromotive force of a thermocouple with its hot junction in the furnace, switched the furnace current between high and low settings. The temperature distributions in the working zones of the furnaces were determined with calibrated Pt/Pt-10 pct Rh thermocouples. The overall uncertainty in temperature was estimated to be ±3° at 915° to 999°C and ±5° at 1217°C . Consideration of the small temperature coefficients of the equilibria studied, together with the error limits in the method of analyzing for nitrogen, showed that further refinement in temperature uniformity would give no improvement in resultant accuracy. The reactive gas was generated by mixing together "prepurified" nitrogen and "electrolytic" hydrogen directly from cylinders commercially supplied. The flow rates of nitrogen and of hydrogen were fixed by setting with bleeders the pressure drops across the individual calibrated flow meters of constant resistance. For any given alloy, the solubility of nitrogen at 1-atm pressure (% N) was obtained from the analyzed nitrogen content of equilibrated specimens (% Na)according to Sieverts&apos; law, thus

Jan 1, 1962

By B. C. Allen, W. D. Kingery

Surface tension and its temperature dependence have been determined for pure liquid Fe, Cu, Co, Ni, and Sn and for Fe-C, Co-C, and Ni-C alloys. The temperature coefficient of surface tension is negative for all these liquids. The surface tension and wetting behavior of tin and tin-titanium alloys on A120,, Si,N,, MoSi,, and Sic, as well as the behavior of titanium-containing nickel alloys on A1 20, have been determined over a wide temperature range. For all the solids investigated titanium additims markedly lower the contact angle. Some limits for the solid-surface energies have been calculated from liquid surface tension and wetting behavior. SURFACE tension and interface energy are important variables in a number of metallurgical and ceramic phenomena, and have been discussed at some length in connection with determining micro-structure of polyphase systems,&apos; solid-state sintering,&apos; thermal etching of grain boundaries, heats of solution and fine powders,&apos;1 grain-growth phenomena,&apos; the mechanical behavior of fine foils and fibers, nucleation, soldering and brazing,&apos; and other phenomenz of academic or practical interest However, until recently few quantitative data have been available for high-temperature systems. Among available data are some indicating positive temperature coefficients for the surface tension of liquid copper,*,11,&apos;2 cast iron,l3 and iron-carbon14 alloys. Although carbon was found to be not surface active in iron at 1570" some preliminary studies had indicated the possibility of a positive temperature coefficient for the eutectic composition at lower temperatures.16 One part of the present study has been largely concerned with determining the temperature coefficient of surface tension for several metals at elevated temperatures, In addition to surface-tension studies, the wetting behavior of alloys containing titanium has been investigated over a wide temperature range. Previous measurements indicated that titanium was selectively adsorbed from nickel at a liquid nickel-solid alumina interface,17 and the use of titanium hydride or titanium-alloy techniques for metal-ceramic soldering is well known. In the present study, previous data have been extended to new alloy systems, and measurements have been carried out with other oxidation-resistant ceramics. EXPERIMENTAL The sessile-drop method was employed to measure liquid surface tension and contact angle between liquid and solid, utilizing apparatus and techniques which have been described previously.&apos;g The shape of a sessile drop depends on equilibrium between forces of surface tension tending to form a spherical surface of minimum area and forces of gravity tending to flatten the drop. Typical sessile drops are shown in Fig. 1. From precise measurements of maximum drop diameter and drop height the surface tension and drop volume were calculated. Four solid materials were employed as supporting plaques for the liquid-metal drops. Aluminum oxide (99.9 pct, J, T. Baker, reagent grade) was pressed and sintered at 1800°C. Molybdenum-disilicide powder (99.0 pct, Electro Metallurgical Co.) was pressed and sintered at 1650°C. Plaques were cut from silicon carbide (99.4 pct, hot-pressed at Alfred University) and silicon nitride (95.1 pct, with Al, Fe, 0 as major impurities, Norton Co.) rods. All plaques were polished, cleaned, and dried prior to use. A number of metals and alloys were employed. Chemical analyses of vacuum-melted ingots of iron, nickel, cobalt (National Research Corp.), commercial nickel-base alloys, electrolytic copper (International Smelting and Refining Co.), and tin (Mal-linckrodt Chemical Works) are given in Table I. Alloys were prepared in the laboratory by vacuum melting the base metal with either titanium hydride (Metal Hydrides, Xnc.) or spectroscopic-grade carbon (National Carbon Corp.). Nickel-titanium alloys contained between 0.001 and 0.005 pct oxygen and the ferromagnetic metal-carbon alloys contained 0.001 pct. Cylindrical metal specimens (1 to 2.5 g) were machined and bevelled at the bottom to insure a uniform advancing contact angle on melting. Before use the samples were acid-etched, cleaned with acetone, and rinsed in petrol ether.

Jan 1, 1960

By A. L. Mular

The flotability of crushed zinc oxide pellets which were doped to produce more n-type or less n-type (more p-type) properties was studied with a Halli-mond tube. Flotation data are presented to show that the pH at which 50% recovery occurs and the collector concentration for 50% recovery depends upon the concentration of doping agent added substitu-tionally for zinc in zinc oxide. The time of sintering of pellets has a slight effect on flotation behavior. A speculative model is proposed to explain the observed behavior in light of the fact that zinc oxide is a semiconductor and has a space charge region at the surface. Experimental verification is necessary before the proposed model can be established as correct. In recent years, the attachment of flotation reagents to minerals has been shown to depend upon the behavior of an electrical double layer which exists in the liquid near the mineral-liquid interface.&apos; Thus, a mineral placed in water will undergo a surface re-arrangement, most likely be preferential dissociation of lattice atoms or by surface adsorp-tion-desorption reactions, to form a dissociation electrical double layer with the solution. Among the many factors which influence adsorption processes, the past history of the mineral itself is one of the most important. Because of trace impurities, minerals from different localities may exhibit marked differences in flotation behavior. This is not unexpected, since investigators who have studied the detailed structure of the double layer&apos;s3 have known for some time that the impurity content of many minerals may exert strong influence on double layer variables. For this reason, their studies were usually made with minerals of high purity. The precise relationship between impurities in a mineral and double layer parameters such as capacity and electrostatic potential has been obscure. However, impurities in a semiconductor type mineral which is in contact with a solution have been recently shown to produce changes in the properties of a space charge layer which extends into the bulk of the semiconductor to a distance of one micron or more.4 The double layer is influenced by the space charge layer, whose origin is best discussed in terms of the band theory of solids. A qualitative description of the behavior of impurities in the bulk of a semiconductor, from a chemical point of view, is useful at this point. Briefly, impurities or defects (lattice vacancies, interstitials, etc.) in semiconductors such as PbS, ZnS, FeS2, Cu2S, NiS, NiO, Fe2O3, ZnO, CdS, MnO2 and many others, behave somewhat like acids or bases in water. For example, water dissociates into hydrogen and hydroxyl ions according to

Jan 1, 1965

By B. M. Larsen

IN spite of the great amount of operating experience and of studies directed toward elucidation of the interrelation of the several processes going on in the blast furnace, the present picture of its operation is based largely on indirect evidence and on speculation. The reason for this unsatisfactory situation is the extreme difficulty of making direct observations and significant measurements while the furnace is operating, and of translating laboratory experience to the conditions obtaining in the smelting process. Yet there are questions that can be investigated with some promise of a definitive answer; and it is the purpose of the present paper to set forth some of these questions, as a basis for discussion, which may, it is hoped, lead to active work on some of them. In order to provide a starting point for this discussion, some views held tentatively by the writer are outlined, along with a certain amount of evidence gathered from operating records and interpreted on the basis of the ideas expressed. These opinions may prove not to be pertinent, and may well not be in accord with the opinions of others; they have been included to encourage others to do likewise and on purpose to provoke informal discussion. In this way it should be possible to transcend the limitations of formal papers; to bring forth suggestions of new hypotheses or new methods of investigation; and to promote better understanding between investigators and operators in this difficult field. The statements made express the present views of one physical chemist who is not too familiar with all the difficulties of maintaining these enormous reaction vessels in reasonably smooth and economical operation; who, however, is persuaded that some of these difficulties would be less formidable if surer knowledge of the several interrelated and concurrent processes were available and made use of. For these difficulties arise largely, it is believed, from variation in conditions which the operator must meet as best be can, and should lessen as these conditions can be brought under control so that they are either made substantially constant or the variations are neutralized by compensating methods. A. VARIATION IN BURDEN AND IN MIXING OF CHARGE To the scientific investigator, who aims to control the conditions of experiment and to limit the number of variable factors, the most perplexing aspect of the blast-furnace process is that nothing seems to remain constant for long. Variations of burden seem to be unnecessarily frequent; and, even if the charge were constant from hour to hour, its constituents usually are not mixed as intimately as they might well be. It is understandable that separate layers of coke and of ore, also separate layers according to size, promote permeability and the

Jan 1, 1947

By G. W. P. Rengstorff, L. E. Olds

High purity molybdenum ingots containing controlled amounts of a single impurity element (oxygen, nitrogen, or carbon) were prepared. These ingots were tested for ductility by bending test specimens at various temperatures. The relationship between the plastic behavior of the ingots and their chemical composition has been determined. MANY proposed applications for molybdenum require ductility at or near room temperature. At the present time, it is possible to obtain wrought molybdenum with considerable ductility only if special fabrication techniques are used to control the grain structure. Starting with are-cast or powder metallurgy ingots, the usual methods for obtaining ductility rely on fabrication procedures that result in fibered microstructures in the finished product. Recently, it has been found that the ductility of either powder metallurgy or are-cast molybdenum can be improved by uniform recrystallization of the metal to a very fine equiaxed grain structure.&apos; The need for a fibered or a fine grained structure may limit the practical usefulness of molybdenum. For example, welding. which may be used in fabricating the metal, generally produces coarse grained structures that lead to brittleness. This applies, certainly, to currently available commercial molybdenum. Although commercial molybdenum is brittle when the grains are coarse, it has been shown experimentally that fine grained structures are not always essential for ductility. For instance, as-cast molybdenum with a coarse columnar grain structure is ductile if it is sufficiently pure.&apos; Because high purity cast molybdenum has good ductility even when coarse grained, it is probable that the brittleness in coarse grained commercial molybdenum is caused by the impurity content of the metal. Although the general effects of impurities on the cold ductility of molybdenum have been known in a qualitative manner for some time, no quantitative evaluation of these effects has been available. The present investigation was made in order to determine more accurately the effects of oxygen, nitrogen, and carbon on the cold ductility of cast molybdenum. Oxygen has long been known to be detrimental to ductility, although the minimum amount which will embrittle molybdenum has been open to speculation. Parke and Ham" showed that ingots with oxygen contents above 0.003 pct could not be forged. Maringer and Schwope have described the embrittle-ment of molybdenum wire by oxygen. A discussion on the effects of heat treatment on the distribution of oxygen in molybdenum has been given by Perry, Spacil, and Wulff." Although nitrogen would also be expected to have harmful effects on ductility, no extensive work has been done previously to determine whether this is so. However, Tury and Krausz" found that wires presumably with less than 0.007 pct N were brittle. Carbon is added to commercial cast molybdenum for deoxidation. Parke and Ham" have shown that molybdenum containing as much as 0.06 pct C could be forged if the oxygen was kept below 0.003 pct. Also, Bruckart and others&apos; found that the room temperature ductility of sintered molybdenum improved with carbon contents up to 0.84 pct. However, Rengstorff and Fischer&apos; found that residual carbide particles in cast molybdenum apparently had an unfavorable effect on room temperature ductility.

Jan 1, 1957

By J. N. Chew, C. A. Connally

A correlation is presented for predicting the viscosity of gas-saturated crude oils under reservoir conditions. It is based on the dead oil viscosity and the solution GOR. The correlation was developed from a study which showed that at a fixed solution GOR, the relation between the gas-saturated oil viscosities and the correrponding dead oil viscosities is a straight line on logarithmic coordinates. Data from 457 crude oil samples from the major producing areas of the U. S., Canada and South America were used. The best straight lines through the data were fitted by the method of least squares with a digital computer. The correlation is presented in the form of an equation and also in a convenient gra-phical form. INTRODUCTION The viscosity of gas-saturated crude oils under reservoir conditions is an important physical property used in reservoir engineering calculations. Many difficulties are inherent in the sampling of gas-saturated oils and in the laboratory measurement of their viscosities. Therefore, it is frequently neither possible nor convenient to obtain measured values, so the viscosity must be estimated from other, more readily available data. This paper presents a correlation for predicting the viscosity of gas-saturated crude oils. The correlation is based on the amount of gas in solution and the viscosity of the dead oil at the temperature of interest. A previous correlation of these variables was presented by Beal. In comparison, the correlation presented here extends to a higher GOR and to a lower dead oil viscosity. Over the range of variables covered by both, this correlation is based on approximately 11 times as many oil samples. DEVELOPMENT OF CORRELATION A study was made of the variables or parameters which could be used to relate the viscosity of a gas-saturated oil to its dead oil viscosity. Preference was given to those variables which are easily and commonly measured in the field or in the laboratory. It was found that either the differential liquid formation volume factor or the solution GOR of the gas-saturated oil could be used as a correlating parameter. The solution GOR was se- lected for the correlation because of its simplicity and availability. In an attempt to refine the correlation by introducing a second parameter, the following additional variables were tested: differential liquid formation volume factor at the reservoir bubble point, the formation volume factor at the saturation pressure for the GOR of interest, reservoir temperature, viscosity of C+ fraction at 100°F and atmospheric pressure, weighted average gravity of gas in solution, oil gravity, reservoir bubble point pressure, saturation pressure at the selected GOR and reservoir temperature, and gas mol fraction. None of these improved the correlation to any significant extent. It was found that at any fixed solution GOR, the relation between the gas-saturated oil viscosities and the corresponding dead oil viscosities is a straight line on logarithmic coordinates, for the range of variables investigated. This straight-line relationship was used for the correlation. Viscosity data on a total of 457 crude oil samples were used. The data were obtained with rolling ball-type viscometers. The samples came from all of the important producing areas of the U. S., as well as from Canada and South America. Their geographical distribution is shown in Table 1. The ranges of properties represented by these samples are as follows: For each crude oil sample the viscosity of the liquid phase from each step of a differential liberation was plotted against its solution GOR on semi-logarithmic paper. A smooth curve was drawn through the points and values of viscosity in centipoises were read from

By L. F. Mondolfo

R301 is a clad aluminum alloy, composed of a core of a duralumin-type alloy clad with a magnesium silicide alloy. It differs from other well-known clad alloys in that the cladding and the core respond to the same heat-treatments, and therefore the cladding contributes appreciably to the mechanical properties of the material. In Table 1 are reported the compositions of the core and cladding alloy for the material used for the experiments. [ ] In clad aluminum alloys where the core contains copper and the cladding does not, at elevated temperatures the copper tends to diffuse from the core through the cladding. This fact is well known and many investigations have been conducted to determine the features of this diffusion.1-7 Most of those investigations cover materials clad with pure aluminum; the present investigation covers a material clad with an alloy. Since the cladding thickness on R301 varies with the gauge, as shown in Table 2, several gauges were investigated. [ ] MATERIAL AND PROCEDURE The material used was sheet of the following gauges: 0.025, 0.040, 0.064, 0.102, 0.170. Cut in pieces approximately 3 by 5 in., it was in the cold-rolled state and was soaked for increasing times at the following temperatures: 910°F., 940°F., 970°F. A Lindberg cyclone furnace was used for the experiments. The procedure was as follows: The furnace was started empty with controlling pyrometer set at the determined temperature. After the furnace had reached that temperature, it was run for some 20 to 30 min. empty, in order to allow the temperature inside to become stabilized. Then the first samples were introduced. A load thermocouple, with recording pyrometer, was connected with the sample of the heaviest gauge. About 10 min. was required for the material to reach temperature and the soaking time was counted from that point. After 200 min. soaking, the second group of samples was introduced without stopping the furnace. After 200 min. more, the third group of samples was introduced, and so on, until the last sample had been introduced. Every time the furnace was opened and new samples were added, a drop of temperature was registered by the thermocouple connected with the material

Jan 1, 1945

By I. R. Kramer, P. D. Gorsuch, D. L. Newhouse

Although many methods have been suggested for the calculation of tensile strength and yield point from chemical composition, their usefulness has been limited to a particular cooling rate or section size. Further limitations have been imposed by failure to take into account many of the alloying elements that exert a considerable influence on the tensile strength or yield point. These systems, nevertheless, have filled an important need in many instances. The value of a system for the calculation of the tensile properties from the chemical composition and cooling rate is that it permits the prediction of the effect of alloying elements and heat-treatment on the mechanical properties, so that more efficient use of alloying elements may be made. Furthermore, it aids in the choice of steel for a given application aid tends to decrease the number of steels that otherwise would have to be tested. It is the purpose of this work to present a method of calculating tensile strength and yield point from the chemical composition and to suggest a method of correlating the tensile-strength and yield-point factors and cooling rate. Steelmakers have been interested for many years in the calculation of the tensile strength of hot-rolled steels. Quest and Washburn&apos; summarize several of the attempts that have been made to devise formulas. They show the inadequacy of each of these formulas and present one of their own. It is apparent from their work that a simple additive equation of the type TS = A + BX + Cy + DZ + . . . , where A, B, C, D, etc. are experimentally determined constants and x, y, z, etc., are the percentages of alloying elements present in the steel, is not adequate to analyze fully the situation encountered in the calculation of tensile strength. For example, it was found that the difference between the calculated and observed values became progressively greater as the carbon and manganese contents were increased. Therefore, the effect of manganese was given as a function of the carbon content. Grossmann, in his work on the harden-ability of quenched steels, and Walter, in his method of calculation of tensile strength of normalized steels, present two cases in which multiplying factors were successfully used to express the combined effect of alloying elements. The factors in both cases were obtained from the fractional increase in hardenability or tensile strength with increase of alloy content. Yield point often is more important in design than tensile strength. For quenched and tempered steels a linear correlation exists between yield 2nd tensile strength.4 This is not true, however, for normalized

Jan 1, 1948

By J. R. Lewis

During the past few years there has been considerable interest in the sizing and the preparation of the iron ore fed into blast furnaces. Furnacemen know that proper sizing of ore tends to increase the efficiency of the furnace. It has been shown by Joseph1 and his associates that there is a direct relationship between the porosity of an ore particle and the time required for its reduction in the blast furnace. This relationship may be stated as follows: All other factors remainig constant, the time for reduction of a given sample of ore is inversely propor-tiofid to its porosity. As a consequence, large pieces of very porous ore, say 3 or 4 in. in cross section, will be completely reduced by the time they reach the hot zone just above the tuyeres, while large pieces of dense, nonporous ore may reach the hot zone with their centers unreduced. This means that for the latter complete reduction will be accomplished by the so-called "direct method;" i,e., where carbon reacts directly with the ore. Some recent work by philbrook2 seems to contradict this rule. He found that of two unlike ores he studied, the one with the lower porosity reduced more readily. He explained his results as "possibly due to an apparently greater tendency of the rA, ore (lower porosity) to crack during preliminary dehydration and during reduction." This brings his results in line with the rule stated above. It is not the author&apos;s intention to enter into a discussion of the merits of "direct" versus "indirect" reduction. It is enough to Say that, in general, indirect reduction is desirable. For the greatest efficiency, Gruner&apos;s theorem3 requires that all reduction in the blast furnace be indirect. Joseph seems to believe this also, because in his recent article on Some Comparisons between Iron Ore, Sinter and Nodules as Blast Furnace Feed4 he concludes that: "In genera&apos;, the carbon in blastfurnace coke is used most efficiently when the largest amount of the carbon charged reaches the tuyeres." However, P. V. hlartin,3 in an excellent paper, has shown that some direct reduction may actually increase the efficiency of the furnace; that is, increase its rate of production while maintaining maximum fuel economy. For nonporous ores there is more opportunity to have an excess of direct reduction unless the factors that make for indirect reduction are favored; for instance; the Proper sizing of the Ore particles&apos; Another factor that has an important bearing on the reduction rate, as it is affected by particle size, is the flow of heat into the particle. The ore particle

Jan 1, 1948

By J. R. Lewis

During the past few years there has been considerable interest in the sizing and the preparation of the iron ore fed into blast furnaces. Furnacemen know that proper sizing of ore tends to increase the efficiency of the furnace. It has been shown by Joseph1 and his associates that there is a direct relationship between the porosity of an ore particle and the time required for its reduction in the blast furnace. This relationship may be stated as follows: All other factors remainig constant, the time for reduction of a given sample of ore is inversely propor-tiofid to its porosity. As a consequence, large pieces of very porous ore, say 3 or 4 in. in cross section, will be completely reduced by the time they reach the hot zone just above the tuyeres, while large pieces of dense, nonporous ore may reach the hot zone with their centers unreduced. This means that for the latter complete reduction will be accomplished by the so-called "direct method;" i,e., where carbon reacts directly with the ore. Some recent work by philbrook2 seems to contradict this rule. He found that of two unlike ores he studied, the one with the lower porosity reduced more readily. He explained his results as "possibly due to an apparently greater tendency of the rA, ore (lower porosity) to crack during preliminary dehydration and during reduction." This brings his results in line with the rule stated above. It is not the author&apos;s intention to enter into a discussion of the merits of "direct" versus "indirect" reduction. It is enough to Say that, in general, indirect reduction is desirable. For the greatest efficiency, Gruner&apos;s theorem3 requires that all reduction in the blast furnace be indirect. Joseph seems to believe this also, because in his recent article on Some Comparisons between Iron Ore, Sinter and Nodules as Blast Furnace Feed4 he concludes that: "In genera&apos;, the carbon in blastfurnace coke is used most efficiently when the largest amount of the carbon charged reaches the tuyeres." However, P. V. hlartin,3 in an excellent paper, has shown that some direct reduction may actually increase the efficiency of the furnace; that is, increase its rate of production while maintaining maximum fuel economy. For nonporous ores there is more opportunity to have an excess of direct reduction unless the factors that make for indirect reduction are favored; for instance; the Proper sizing of the Ore particles&apos; Another factor that has an important bearing on the reduction rate, as it is affected by particle size, is the flow of heat into the particle. The ore particle

Jan 1, 1948

By P. D. Gorsuch, I. R. Kramer, D. L. Newhouse

Although many methods have been suggested for the calculation of tensile strength and yield point from chemical composition, their usefulness has been limited to a particular cooling rate or section size. Further limitations have been imposed by failure to take into account many of the alloying elements that exert a considerable influence on the tensile strength or yield point. These systems, nevertheless, have filled an important need in many instances. The value of a system for the calculation of the tensile properties from the chemical composition and cooling rate is that it permits the prediction of the effect of alloying elements and heat-treatment on the mechanical properties, so that more efficient use of alloying elements may be made. Furthermore, it aids in the choice of steel for a given application aid tends to decrease the number of steels that otherwise would have to be tested. It is the purpose of this work to present a method of calculating tensile strength and yield point from the chemical composition and to suggest a method of correlating the tensile-strength and yield-point factors and cooling rate. Steelmakers have been interested for many years in the calculation of the tensile strength of hot-rolled steels. Quest and Washburn&apos; summarize several of the attempts that have been made to devise formulas. They show the inadequacy of each of these formulas and present one of their own. It is apparent from their work that a simple additive equation of the type TS = A + BX + Cy + DZ + . . . , where A, B, C, D, etc. are experimentally determined constants and x, y, z, etc., are the percentages of alloying elements present in the steel, is not adequate to analyze fully the situation encountered in the calculation of tensile strength. For example, it was found that the difference between the calculated and observed values became progressively greater as the carbon and manganese contents were increased. Therefore, the effect of manganese was given as a function of the carbon content. Grossmann, in his work on the harden-ability of quenched steels, and Walter, in his method of calculation of tensile strength of normalized steels, present two cases in which multiplying factors were successfully used to express the combined effect of alloying elements. The factors in both cases were obtained from the fractional increase in hardenability or tensile strength with increase of alloy content. Yield point often is more important in design than tensile strength. For quenched and tempered steels a linear correlation exists between yield 2nd tensile strength.4 This is not true, however, for normalized

Jan 1, 1948

By P. D. Gorsuch, D. L. Newhouse, Irvin R. Kramer

ALTHOUGH many methods have been suggested for the calculation of tensile strength and yield point from chemical composition, their usefulness has been limited to a particular cooling rate or section size. Further limitations have been imposed by failure to take into account many of the alloying elements that exert a considerable influence on the tensile strength or yield point. These systems, nevertheless, have filled an important need in many instances. The value of a system for the calculation of the tensile properties from the chemical composition and cooling rate is that it permits the prediction of the effect of alloying elements and heat-treatment on the mechanical, properties, so that more efficient use of alloying elements may be made. Furthermore, it aids in the choice of steel for a given application and tends to decrease the number of steels that otherwise would have to be tested. It is the purpose of this work to present a method of calculating tensile strength and yield point from the chemical composition and to suggest a method of correlating the tensile-strength and yield-point factors and cooling rate. Steelmakers have been interested for many years in the calculation of the tensile strength of hot-rolled steels. Quest and Washburn&apos; summarize several of the attempts that have been made to devise formulas. They show the inadequacy of each of these formulas and present one of their own. It is apparent from their work that a simple additive equation of the type TS = A + BX + Cy + DZ + ? ? ? , where A, B, C, D, etc. are experimentally determined constants and x, y, z, etc., are the percentages of alloying elements present in the steel, is not adequate to analyze fully the situation encountered in the calculation of tensile strength. For example, it was found that the difference between the calculated and observed values became progressively greater as the carbon and manganese contents were increased. Therefore, the effect of manganese was given as a function of the carbon content. Grossmann,2 in his work on the hardenability of quenched steels, and Walters,3 in his method of calculation of tensile strength of normalized steels, present two cases in which multiplying factors were successfully used to express the combined effect of alloying elements. The factors in both cases were obtained from the fractional increase in hardenability or tensile strength with increase of alloy content. Yield point often is more important in design than tensile strength. For quenched and tempered steels a linear correlation exists between yield and tensile strength .4 This is not true, however, for normalized

Jan 1, 1946

By Bruce W. Gonser, Robert J. Nekervis

EACH metal has a unique combination of properties that distinguishes it from other metal;. Su& a combination may account for applications that cannot be met very well by anything else. This is particularly true of tin, one of the earliest metals used by man. Table i shows the consumption of tin in the United States by usage for the years 1949 and 1950, which may be considered to be generally typical of current usage. The major applications-tinplate, solders, bronze, and babbitt-were well established a century ago. Applications for the metal and (probably later) of tin alloys started more than 5000 years ago. Fortunately for the ancients, tin is one of the metals whose oxide is easily reduced by carbon. Nature further simplified the refining problem by providing only one ore of commercial importance, cassiterite (SnO2). Tin is easily reduced from cassiterite. All that is necessary is high heat in the presence of carbon. It is quite possible that back in the dawn of history, tin was discovered when black alluvial sand was thrown on a fire, either to bank it or to put it out. SOURCES OF TIN All the important tin-producing centers are in the southern hemisphere, far away from the&apos; industrial consuming centers. Fig 1 shows their location and 1950 production. Reserves are adequate, and the industry is able to produce considerably more tin than is

Jan 1, 1953

By Donald W. Scott, Nathaniel Arbiter, A. C. Richardson

THIS paper describes the application of amine flotation to a specific problem-that of increasing the grade of magnetite concentrates derived from an iron ore requiring extremely fine grinding for mineral liberation. Experiments conducted on an iron ore from Wisconsin had shown that concentrates containing 60 to 62 per cent iron and 12 to 14 per cent silica could be produced by magnetic separation. The residual silica occurred as quartz and hornblende, either entrained or locked with magnetite. Most advantageous utilization of the concentrate, however, necessitated that the silica content be reduced to about 5 per cent, equivalent to an iron content of 67.5 per cent. It had been demonstrated that tabling of the magnetic concentrate removed sufficient quartz and hornblende to yield an acceptable concentrate, but disadvantages inherent in tabling dictated that flotation be investigated as a substitute. The goals set for the flotation investigation were: (I) the production of concentrates of about 68 per cent iron content from the magnetic concentrate; (2) an iron recovery of about 85 per cent of that in the feed to flotation; and (3) minimum reagent cost. Both batch and continuous flotation tests were employed; the former, to establish the procedure and the latter to verify it. Although the data were obtained on a specific ore, and with a commercial application in view, it is believed that they have a bearing on other problems where amine flotation is being used or is anticipated. SAMPLES Two samples, designated "minus 100mesh magnetic concentrate" and "minus 150-mesh magnetic concentrate," were used for the batch experimental work. They differed only in the degree to which the crude ore was ground prior to magnetic separation. They were stored moist in steel drums in quantities sufficient for all the experimental work reported. This procedure had the advantage of allowing all tests to be made on common samples, but had the disadvantage that the individual flotation samples, because of the difference in storage time, were subject to various stages of surface alteration. Previous work had indicated that common samples were desirable for the batch studies, and it was decided that if these data appeared sufficiently promising the effect of surface alteration could be checked best by continuous tests. The size distributions and the assays of the samples are given in Table I. The minus 150-mesh magnetic concentrate, on which most of the flotation tests were made, assayed 60.9 per cent iron, 13.3 per cent silica, and 0.016 per cent phosphorus. The minus 325-mesh portion represented 78.1 per cent of the sample by weight, and assayed 67.9 per cent iron. Thus, the insoluble, mainly silica, was concentrated

Jan 1, 1945

By W. Rostoker, R. P. Elliott, B. W. Levincer

Phase equilibria in the Ti-Cr-Mo system have been investigated for alloys containing 100 to 40 pct Ti in the temperature range 550° to 1300°C. Five experimental isothermal sections and a surface of incipient melting are presented in addition to a summary projection of the space. Seven vertical sections have been constructed from the isothermal sections. A STUDY of the system Ti-Cr-Mo was undertaken as part of a program sponsored by Watertown Arsenal toward the development of titanium-base phase equilibrium diagrams of potential technical importance to alloy development. The scope of the investigation included the composition range contained by the titanium corner and the line of 64 pct Ti (all compositions are by weight) and the temperature range 550" to 1100°C. A surface of incipient melting was constructed from measurements on a large number of alloys. The system Ti-Cr has been established.&apos;-? The phase diagram is characterized by a wide miscibility field of the solid solution at elevated temperatures and a eutectoid reaction of the type: (15 pct Cr) + TiCr, (685C). The a solid solution has a very limited capacity for solution of chromium (< 0.5 pct Cr). The intermediate phase TiCr2 has at best a very narrow composition range. It has been shown that two allotropic modifications of this phase exist. However, this behavior does not appear to be perceptibly reflected in the form of phase boundaries of the type + TiCr,. In the system Ti-Mo,9-10 the phase is stabilized to successively lower temperatures with increasing molybdenum content. There are no known intermediate phases. The a solid solution is limited to less than 0.5 pct Mo. Because of the very extensive range of the phase, the ternary system was ideally suited to the determination of the phase boundaries by the parametric method of Andersen and Jette." A parametric surface was constructed to provide the necessary basis for the application of this method. Preparation and Treatment of Alloys More than 60 alloy compositions were prepared for the study of this system. Alloy buttons of 10 grams were arc-melted in a nonconsumable electrode furnace using inert atmosphere protection and a water-cooled copper crucible. The construction and operation of this type of melting unit have been adequately described elsewhere.&apos;&apos; To insure complete solution of alloy additions, the buttons were remelted alternately on top or bottom as many as five times. This was accomplished by a suitable mechanism for "flipping" over the ingots. Iodide titanium (99.97 pct Ti) was used as the alloy base. An especially high quality chromium (99.9 pct Cr) was obtained from the National Research Corp. Molybdenum sheet (0.005 in.) of 99.9 pct purity was used.

Jan 1, 1954

By D. G. Westlake

Polycrystalline tensile specimens of various Zr-0-H alloys have been tested at 298°, 178°, and 77°K. Solute oxygen and hydride precipitates in quenched alloys made individual contributions to the yield strength at 0.2 pct strain which combined to produce a resultant strength increment, a,., Ductility changes which were ohserved can he interpreted in terms of the various oxygen and hydrogen concentrations, testing tem -peratures, and dispositions of the hydride. ADDITIONS of oxygen in solid solution were known to increase the yield and tensile strengths of polycrystalline zirconium as early as 1951.&apos; More recently, the critical resolved shear stress (CRSS) for prism slip in zirconium single crystals was also shown to be affected by the solute oxygen impurity.&apos; This latter work also demonstrated that large increments of strength could be contributed by the finely dispersed zirconium hydride precipitates that are present in quenched Zr-H alloys.3 It was concluded that the combined strengthening due to alloying could be expressed by where to is the increase in the CRSS due to solute oxygen alone and TH is the increase due to finely dispersed hydride precipitates. Eq. [I] is analogous to one used to express the combined strengthening effects of work hardening and neutron radiation damage.4 Eq. [1] was verified only indirectly and for only small amounts of the impurities—up to 0.14 at. pct 0 and 0.63 at. pct H. The present investigation was undertaken to obtain a more direct verification of the validity of the form of Eq. [1] for this system and also to determine the combined effects of oxygen and finely dispersed hydride precipitates on the tensile strength and ductility of polycrystalline zirconium. EXPERIMENTAL PROCEDURE Tensile specimens were machined from the same rolled billet of Kroll zirconium used in the earlier study.&apos; These measured 38 by 4.7 by 0.5 mm and had 10-mm gage lengths which were 2.8 by 0.5 mm. Each specimen was ß-annealed in vacuo at 1173°K for 15.5 hr and a-annealed at 1073°K for 4 hr to D. G. WESTLAKE, Member AIME, is Associate Metal l ur-gist, Metallurgy Division, Argonne National Laboratory, Argonne, III. Manuscript submitted July 17, 1964. IMD______________ give an equiaxed structure with grain diameters averaging 0.06 mm. Oxygen was added by allowing the metal to react with a known quantity of oxygen during the 0 anneal and known quantities of hydrogen were added during the a anneal. Each alloy was encapsulated in Pyrex under vacuum, annealed at 873°K for 4 hr, quenched into ice water, and polished by immersion in a solution of 46.75 vol pct H2O, 46.75 vol pct concentrated HNO3, and 6.5 vol pct HF (49 pct) at 298°K. Special heat treatments given to a few specimens are described in the results below. Tensile tests were done on an Instron machine and were begun within 20 min after the quench, except where specified otherwise. Tests at 298°K were in air, at 178°K in acetone, and at 77°K in liquid nitrogen. All tests were at a strain rate of 8x sec-1. RESULTS AND DISCUSSION Yield Stress at 298°K. The compositions of alloys and the corresponding yield stresses (0.2 pct strain) are given in Table I. A plot of the yield stresses of the oxygen alloys, A, B, C, and D, indicates that varies linearly with CO1/2, where Co is the oxygen concentration, Fig. 1. This is in accord with Fleischer&apos;s6 theory for solution strengthening if the oxygen atoms do not cluster, or the cluster size remains constant with increasing oxygen concentration. In Fig. 1, it appears that if one could prepare some oxygen-free zirconium its yield stress would be very low. Therefore, we shall assume that for the oxygen alloys is equivalent to O0, the strength increment contributed by the presence of oxygen. The relationship between0.2and Co is expressed by 0.2 = 31.3 CO1/2, when the yield stress is in kg per sq mm and the concentration is in at. pct. Each of the hydrogen alloys, Al, A2, A3, and A4, contained 0.081 at. pct 0 as an impurity. In Fig. 1, it appears that this small amount of oxygen makes a significant contribution to the strength which cannot be ignored when we evaluate the contribution of the finely dispersed hydride. Let us assume the validity of the following equation: a0.2 = (a2o+a2R)1/2 [2] which is analogous to Eq. [I] for single crystals, and calculate values of UH for the hydrogen alloys by using the experimental values of 0.2 and o (0.081 at. pct) = 8.9 kg per sq mm. For 0.36 at. pct H, oH = 6.47; for 0.72 at. pct H, OH = 11.30; for 2.16 at. pct H, OH = 19.4; and for 3.60 at. pct H,

Jan 1, 1965