Search Documents

By Robert Warner

WHEN a new mine is opened, and often when an operating mine must adapt itself to physical or economic changes, a mining system must be selected in complete detail. In the past the plan chosen was usually the product of the local staff alone, however limited the training and experi-ence of that staff might be, which often resulted in the introduction of methods that were familiar to the staff, but not so well suited to the con-ditions as others unknown to the local men. A new management, noting the difficulties with the existing layout, might make modifications or complete changes, so that many mines in their history have seen a whole series of mining systems, each somewhat laboriously grafted on to its predecessor. This should not be interpreted as a condemnation of the older staffs for sticking to the tried systems, such as open square-sets in the early days at the Homestake, because they knew it would work after a fashion, nor does the statement apply to the technically trained, and usually broadly experienced staffs of most present-day properties. The older miners did not have the variety of tools and methods, nor the present freedom of transfer of information as to what the other man is doing, and so did the best they could under the circumstances. Finally, the higher grade of the ores made the choice less vital. The ever-increasing need to mine low-grade orebodies, with a fixed or even lower price for the metal produced, has caused an increasing need for low-cost mining. In most new mines this has simplified the problem of selection by eliminating from consideration all of the high-cost systems, but it has also complicated the choice by the necessity for refinement in detail and a close adjustment of the plan selected to all the conditions at the property. In these low-cost problems any textbook division of mining systems as applied to "beds, veins or masses" avails little as a guide. It should be realized at the outset that to' be successful under modern competitive conditions a system of mining must be worked out with elaborate detail, with careful time scheduling and control of the various elemental operations, and that after it is introduced it must be run with a large amount of technical direction.

Jan 1, 1933

By Harry L. Brown, Philip E. Armstrong

Young's modulus doto ore presented for W, Mo. Ta. V, Cr. Ni, Ti, and Zr as a function of temperature up to about 0.7 of the melting points. A plot of reduced temperature us reduced modulus produces a general correlation except for titanium and zirconium. Young's modudlus data for some representatiue commercial graphites are given up to 2400°C. All results were obtained from longitudinal resonance-frequency measzrrements of 4-in. long samples, corrected for simultaneously measured thermal expansion. Comparison of poly crystalline and single-crystal tungsten behavior indicates that all the observed modulus values are frequencv -dependent at the higher temperatures. STATIC measurements of elastic properties of materials at elevated temperatures are extremely difficult to make since the elastic behavior is obscured by relatively large first-stage creep effects. Dynamic methods which avoid this difficulty by utilizing the measurement of the resonance frequency of a simple vibrational mode have been described in the 1iterature.l-3 The authors have extended the operating temperature range of this type of measurement to above 2000°C and have described the equipment elsewhere.~ The Young's modulus data presented here were obtained with this equipment, using samples about 4 in. long and 1/4 in. diam, supported horizontally at the center and excited to the fundamental longitudinal resonance frequency. Young's modulus was calculated by the formula: E = 4f2f2p where E = Young's modulus, / = frequency, 1 = length, and p = density. Dilatometric data were obtained simultaneously by optical measurements of the change of length of the sample. For the metals tested, an attempt was made to obtain modulus values that would be representative of the pure, strain-free, randomly oriented material. All of the graphites studied exhibited a high degree of elastic anisotropy, while the method assumes an isotropic homogeneous material. However , when the values for Young's modulus obtained for AUC graphite were compared with those taken from static measurements at room temperature they were found to be only about 4 pet higher. This is excellent agreement considering the low precision of modulus calculations from stress-strain curves. The difficulty in using data of apparent Young's modulus for anisotropic materials arises when the attempt is made to use these data and shear-modulus data to obtain Poisson's ratio. The results are usually meaningless and sometimes absurd.' RESULTS Table I lists the sources, impurity content, thermal history, and dilatometric constants of the metal samples that were investigated. All the metal samples were tested under a vacuum of 1 to 5 x 10-5 Torr. Where our dilatometric data agreed with previously published data, the table lists the previous values and the literature reference. Where no reference is given, the constants were determined from our dilatometric data. Table II presents the modulus data in units of millions of psi as a function of temperature in degrees centigrade. The numbers were obtained from curves fitted to the experimental data. For some types of calculations, such as those attempting to correlate creep data, the slope of the modulus curve is of interest, and this information also is reported in Table 11. It is always tempting to try to fit physical-property data into some general pattern and then use this pattern to predict the behavior of other similar materials. The general pattern for an elastic modulus of a metal seems to be a linear deoro- with increasing temperature Over the range between 0.1 and 0.4 of the melting temperature, then a progressive1y decreasing value up to the melting point. Metals appear to retain finite moduli

Jan 1, 1964

By William H. Radford

Having worked some rather lorn--grade gravel during the past season at a small profit, I give the actual figures, in the hope that other mining engineers interested in this line of work may be thereby induced to do the same, in order that we may all get more data on this little-ventilated subject. The property here referred to is situated in one of the northern counties of California, where hydraulic mining is still permitted by the courts. The water-right belonging to the mine is a good one, furnishing water during about nine months, whenever there is an average rain-fall, and a fair proportion of the precipitation is in the form of snow. The ditch, about 11 miles in length, is cared for during the rainy months by two men, and during the rest of the year by one; and the water cost last season, delivered at the mine, 0.69 cent per miners' inch. The season commenced in November, 1899, and ended the last of July, 1900. During this time, 655,657 miners' inches (an inch equals 1728 cu. ft. in 24 hours) of water were used for piping, and for sweeping the bed-rock at the end of the season. From actual surveys, this amount of water washed down 1,251,399 cu. yds. of material, consisting of pay-gravel lying on the bed-rock, and varying in thickness from a few inches to 8 ft., and practically barren top-material, consisting of mountain slide, carrying considerable broken rock, clay, and soil. The banks varied in height from 50 to 130 ft., the average height being 63 ft. The grade of the sluices was 7 in. to 12 ft., the boxes being paved with block-riffles 12 in. deep. Long bed-rock cuts extended from the heads of the sluices to within a few feet of the banks, and were kept practically to grade as the work advanced. At first, electric drills were used on this work; hut as it was found that heavy blasting shattered the rock too much, and caused slips, these drills were

Jan 1, 1902

By L. R. Jackson

THE idea presented in this paper is that the capacity of a metal for plastic flow before rupture is dependent on the type of stress system applied-that is, the absolute magnitude of the stresses are unimportant provided that they are large enough to produce continued flow; the important factor is the "type" of stress system. A term called the "triaxial stress ratio" is defined in such a way that this ratio can be used to characterize the "type" of system. The paper is divided into three sections. The first section discusses means of representing the effect of complex stresses on plastic flow and defines "triaxial stress ratio"; the second section discusses various methods of' obtaining complex stress distribution. The third section gives some experimental results showing the effect of types of complex stress on the capacity of various metals for flow. An appendix discusses some details on methods of obtaining complex stresses. I. REPRESENTATION OF COMPLEX STRESS SYSTEMS AND THEIR EFFECT ON PLASTIC FLOW Representation of Stresses It is convenient to have a consistent system of notation that will allow the representation of the entire range of complex stresses from hydrostatic compression to hydrostatic tension on plastic flow in a single diagram. Such a system is provided by making use of the fact that any complex stress system can be resolved into a hydrostatic tension or compression and a pure shear. Consider a stress system having the principal stresses [S1 S2 5 S3]. This system can be resolved into a new system consisting of the three components [ ] and three pure shears. If Sm is positive, the net stress effect is hydrostatic tension; if it is negative, the effect is hydrostatic compression. In order to produce a systematic notation, a quantity that will be referred to as the "triaxial ratio" will be defined by the equation [ ] Sm is given by Eq. I and S1 is the absolute magnitude of the largest principal stress without regard to sign. Table I lists the triaxial ratios for various common systems. [ ] Representation of Strains Strains will be plotted as "true" strains according to the system proposed by Ludwik.1

Jan 1, 1944

By S. A. Montague

Mica can claim a considerably greater importance than would be assumed from its comparatively small dollar volume, which came to about $37,000,000 for the United States industry as a whole in 1957. Mica is one of the strategic minerals. We must depend on imports from distant sources for virtually all of our requirements of high grade block and all of our mica splittings. Mica is essential and indispensable for vacuum tubes and high-performance condensers, two electronic components which are vital military necessities besides being nearly indispensable to civilization today. Composition and Properties Mica is the general name for a group of some nine different minerals, two of which, muscovite and phlogopite, are the minerals used by the mica industry as its raw material. Several of the other varieties are commercially useful-vermiculite, * used for heat insulation in expanded form, and lepidolite, used as an ore of lithium while the others-biotite, roscoelite lepidomelane, paragonite and zinnwaldite have little or no commercial importance. Biotite frequently occurs as an undesirable impurity in muscovite. Table 1 lists various properties and other data concerning muscovite and phlogopite. Chemically, mica is a complex silicate of sodium, potassium and aluminum. Most varieties of muscovite are higher in sodium, and of phlogopite in magnesium. There are no important uses of mica where the chemical analysis is important, except that in some uses of ground mica, the content of iron oxide present as an impurity must be kept to a very low limit. Muscovite occurs in a range of color from the so-called India "ruby" which is more closely a pinkish brown, to light and dark green, with numerous other intermediate shades. Ruby color is usually preferred by industry, especially in the better qualities. When split very thin the color in most [ ] micas disappears. Muscovite mica is frequently found containing black and red "stain" as a homogeneous part of the books or sheets. In most cases this stain or impurity is magnetite

Jan 1, 1960

By Albert F. J. Bordeaux

The immediate vicinity of the sea-shore, affording special facility for the exportation of ores, makes it possible to work certain mines in the Vladivostok district, which, in more remote places of Siberia., would remain unproductive. Outside of the city of Vladivostok the population is small and the country is very little prospected. Additional discoveries of valuable deposits like the large body of calamine which has recently been opened in the neighborhood of earlier worked lead-silver ores, in the Tetiuhe valley, are still in the field of possibilities. For many years gold alone was produced, in part from the coastal rivers and in part from a quartz-vein on Askold island near Vladivostok. But the production is diminishing, and prospectors are looking for other rivers in the interior, such as the tributaries of the Ussuri. These rivers are now more accessible than formerly, due to the slow but gradual development of colonization by the Russian peasants. The few natives of the country, called Orodjones, are of the Chinese race. They resemble the North American Indian and are hardy fur-hunters. They have given some attention to placers and have already shown good specimens of gold-dust from the rivers Iman, Bikin, Noto, etc. Coal-mining was begun in the Vladivostok region more than 20 years ago, but in a somewhat irregular way. The industry is not as yet important and the best coal-seams are badly prospected, or are even neglected. Copper, lead, and iron exist in several places. The amounts give some encouragement to the anticipation that the discoveries will give rise to important metallurgical works. I here present a review of the various deposits, based upon such safe information as is in hand, when I have not drawn upon my personal observations. Fig. 1 is a map of Eastern Siberia, showing the mineral deposits.

Jan 1, 1913

By Chester Washburne

RECENTLY, Messrs. Mills and Wells1 published a thorough chemical study of the waters associated with oil in parts of the Pennsylvania, Ohio, and West Virginia region. Many of their conclusions are of general application and the writer wishes to discuss some of these: Messrs. Mills and Wells show that the composition of the deep brines of the Appalachian fields is such as would be produced by the evaporation of sea water and the precipitation of sodium chloride, combined with reactions with hydrocarbons and other substances. The brines are altered, also, by considerable mixing with meteoric water. They give good reasons for believing that the concentration of the brines was produced by evaporation in the rock pores induced by migrating gas, much of which probably escaped to the surface of the ground. This hypothesis was considered by the writer in a former paper,2 in which main stress was laid on a second hypothesis, that the excess of chlorine in the deep brines may have been due to the entrance of solutions rich in magnesium and calcium chloride which ascended .from a deep, possibly intratelluric, source. Messrs: Mills and Wells present good arguments for the first hypothesis. Underground evaporation by ascending gases probably will be accepted as the best available explanation of the concentration and composition of deep well waters. They have not considered the possibility that, salt waters in deep sands may be concentrated by the diffusion of water vapor through gas into shale. The writer has given reasons3-for believing that capillary forces concentrate gas and oil in the larger openings of rock, such as the pores of sandstones embedded in shale. The gas underground must be nearly saturated with water vapor at; all times, because it always is in contact with the interstitial water of enclosing shales and of the sand-

Jan 9, 1920

By J. B. Cheatham, J. G. Yarbrough

Although adequate removal of cuttings from beneath a drill bit is important for efficient drilling operations, very little basic data are available relative to the fundamentals of chip removal by hydraulic jets. A discussion is presented in this paper of an experimental investigation of the jetting action of hydraulic jets in removing loose particles from the bottom of a cylindrical hole. Conditions for which the jet is no longer capable of removing chips from the bottom of the hole are determined. This situation represents equilibrium between the chip removal force and chip Bolddown forces such as gravity and pressure. In most of the tests loose particles were jetted with water or a water-glycerine mixture to determine the dependence of chip removal on hole size, jet size, height of jet off bottom of hole, flow rate, particle density and fluid viscosity. ,A test with a pressurized mud system indicated that relatively low pressures can completely overcome the removal action of a hydraulic jet. Although the system studied herein is not directly applicable to a rotary drill bit, the work with such simplified systems can provide a better understanding of the chip removal action of jets, and with logical extensions it may provide a reasonable basis for the best use of fluid jets in drilling. INTRODUCTION The primary deterrent to maximum drilling rates is the inability of the drilling system to remove rock cuttings efficiently enough to prevent interference with the drilling action.1-2 The objective of chip removal studies is to permit predicting and controlling removal forces under downhole drilling conditions. Conditions at the bottom of a hole during rotary drilling are exceedingly complex and are not likely to be described in a quantitative way by investigations in terms of the total drilling action until a better understanding is developed of the simplified components of the problem.3 The present study is concerned with the elementary condition of removal of chips by a single central jet. Even this relatively simple model provides mathematical difficulties because of the turbulent nature of the flow from the jet and because of the shape of the bottom of the hole beneath the jet. Theoretical and experimental studies have been made of turbulent jets impinging normally on an infinite body and deductions based on analytical solutions to simplified problems can give some insight into the problem of cutting removal by a jet. However, because of the present lack of understanding of the behavior of the interaction between the fluid jet and the chips being removed, an experimental approach was chosen for the present study. Methods have been developed for maximizing hydraulic horsepower, impact force and jet velocity; but whether maximizing these parameters maximizes chip removal with present drilling bits has not been demonstrated. Simplifying the problem of chip removal may make it possible to develop some understanding of the manner in which the jet velocity is dissipated. Better understanding of a simple case should materially assist in extending analysis to more complicated cases. Thus, we are not concerned in the present study with the rock fracturing process itself but only with the removal of the debris from the bottom of the hole. A problem which is quite similar to the chip removal problem is the suspension of solids in stirred vessels. This problem has been studied by the chemical industry and correlations have been obtained by dimensional analysis which permit the design of mixing vats7 An approach similar to that used in the mixing vat problem is used in the analysis of the jetting data in the present paper. EXPERIMENTAL PROCEDURE The test equipment arrangement shown sche-matically in Fig. 1 allows the jetting action to remove particles until an equilibrium height is attained for each combination of hole size, jet size and flow rate.*** Equilibrium conditions require that the removal force is unable to remove additional particles. This balance between holddown and removal forces implies a relationship between the two forces which is constant for the particular system. When the holddown forces are constant,

Jan 1, 1965

By H. H. Keller, E. J. Couch

Damage to production wells subjected to the high temperatures associated with in-situ combustion projects has been a problem since the advent of this thermal recovery technique. Injection of water down the annulus of hot wells has been successfully utilized for cooling and prolonging the life of such wells. A mathematical model that is suitable for predicting the effectiveness of cooling water in a particular application is developed. Typical results for practical ranges of the various parameters involved are presented. INTRODUCTION In the normal course of in-situ combustion operations, highly damaging conditions develop in the production wells as the combustion zone approaches, and these wells are subjected to high temperatures (up to 1500F). The resulting well damage is recognized as one of the more serious operating problems unique to the in-situ combustion process. Even in operations where well completions have been specifically designed to cope with this problem, the question arises as to how this destructively high temperature can be kept within tolerable limits. A simple and economical approach to this problem is to circulate cooling water down-hole. This method has been used with some success in shallow reservoirs. At greater depths, however, the heat exchange with the overburden surrounding the well and between the fluids in the tubing and the annulus tends to equalize the temperatures of the two fluid streams so that the cooling capacity delivered to the bottom of the hole decreases with well depth. This method would provide no appreciable control over the bottom-hole temperature at great depths. In order to delimit the condition under which cooling by water circulation is effective, the wellbore temperature must be related to the water inlet rate and temperature; to the reservoir depth, production rate, and initial temperature; and to the combustion at at bot tom-hole depth. A model that meets these requirements and that will offer an approach for developing engineering solutions to practical design and operating problems is described in this paper. MATHEMATICAL MODEL Previous studies of temperature distributions include those for flowing wells1p2 and those for hot fluid injection. Adams and Haddenhorst 6 presented solutions for the down-hole circulation of hot oil in the treatment of paraffin-deposition problems. In this paper the thermal model presented by Ramey 4 is adapted to the flow system shown schematically in Fig. 1. Water at temperature Ti is injected at a rate wi and flows down the annulus outside the tubing. It mixes at bottom-hole depth D with the fluids produced at race w from the hot reservoir at temperature T. This mlxtureJ. of injected water and reservoir fluids flows up the tubing and is produced at the surface at TI,. In order to describe the temperature response in this system, we make use of the usual conservation of

Jan 1, 1969

By L. C. Graton

Although marked by numerous well-known attributes of its own, gold does not possess a kind and range of physical, chemical and geological characteristics wholly different and apart from those of other metals. Instead, it is merely one of the family of metals, with its individual and distinctive traits subordinate to the underlying family relationships and resemblances. The geologist concerned with pure science will pursue, therefore, the same general course and will examine the same broad kinds of facts and interrelations when studying the occurrence of gold as when studying that of copper or cadmium, or any other metal. But when we come to consider the use and economics of the metals, we discover that gold differs strikingly from all the others. Gold, in short, is unique, not by virtue of its inherent characteristics, but because of a peculiar and concerted psychological regard in which it is held. It will be evident, therefore, that the geologist who would deal with gold supply must give far greater weight to economic considerations than is required in his contacts with any other metal. If the geologist be called the scientist of occurrence, and the economist the scientist of use, the economic geologist stands as the necessary link between them. Perhaps it is in part because the economic geologist has made himself more familiar with the science of occurrence than with the science of use and has thus in some degree failed to bridge effectively the gap between the two fields, especially with regard to gold, that the usen1 of gold now appear to be in a state of general concern and even of alarm for the security and adequacy of future supplies. In the case of no other mineral commodity do the users, as a rule, trouble themselves greatly about the adequacy of supply except in so far as that may affect the price which they shall have to pay for the commodity. Oversupply, with resulting low price, they regard as a gift of good fortune. As to long-term undersupply, they are generally content to go ahead on faith, leaving the producer to discover as best he may the means for meeting their requirements or the inventor to find a substitute. But history has shown that for gold a different situation exists. While

Jan 1, 1931

"The chief aim in style ought to be absolute precision", said Flaubert. "There is only one noun that can express your idea, only one verb that can set that idea in motion, and only one adjective that is the proper epithet for that noun." Let this be your motto. The engineer tries to be exact in all his measurements; he should measure his language with similar exactness. The technical term is a word of precision. It is not only precise, it is a word-saver. To the unscientific the earth is "a ball slightly flattened at the poles, something like an orange". To the scientific it is "an oblate spheroid". A similar contrast between the precision of the technical term and the vagueness of common words is afforded by a conversation between Ivanhoe and Rebecca: " ' What device does he bear on his shield?' asked Ivanhoe. 'Something resembling a bar of iron, and a padlock painted blue on a black shield.' 'A fetterlock and shacklebolt azure', said Ivanhoe"-using the technical terms of heraldry. It is good style in writing, however, to adapt your manner of expression to the intelligence and experience of the person or persons to whom the writing is addressed. The description of a mine should be worded differently according as it is intended to inform a mining engineer, a director, or a bishop. REMEMBER THE READER. It is as incorrect to write in a technical way for a non-technical reader as to write in a popular way for a technical or scientific reader. That style is best which enables the writer to place himself in the closest mental touch with his reader, to establish the maximum of sympathetic understanding. Let your precision be proportioned to your accuracy. You should not try to be precise in matters that do not admit of

Jan 1, 1931

By William R. Webster

At the Florida meeting of the Institute, in March, 1895, I presented a Note on a Proposed Scheme for the Study of the Physics of Cast-Iron,1 giving an outline which, for convenience of reference, I here repeat. Suggested Lines for DiScuSsion and IvestiGation. I.—Correspondence between chemical composition and melting-point, fluidity, shrinkage, fracture, chill, micro-structure, and other physical properties. II.—Influence of: 1. Cupola-mixture, use of steel and other scrap, oxidized or clean material, 2. Manner of melting, flux, etc., 3. Casting-temperature, A. Fracture. 4. Manner of handling melted metal and B. Micro-structure. method of casting, C. Physical properties. 5. Size and form of casting, D. Shrinkage. 6 Kind of mold, green sand (under dif- on E. Chill. ferent conditions of ramming, amount F. Residual strew of moisture, and skin-dried), dry sand, G. Condition and quan- loam, and chills, tity of carbon and 7. Rate and mode of cooling castings, other elements. 8. Manner and temperature of heating for annealing, 9. Additions of nickel or aluminum, III. —-Segregation as affected by : 1. Composition ; 2. Casting-temperature; 3. Rate of cooling ; 4. Size and shape of casting. IV. —Blow-holes, their volume and position as affected by: 1. Composition; 2. Casting-temperature; 3. Casting-pressure ; 4. Rate of cooling; 5. Size and ehape of casting ; 6. Special additions. It was hoped that a discussion might thus be elicited, similar in interest and value to the discussion of the physics of steel, which had been so widely and gratefully welcomed by students and practitioners in that department. That this hope was not

Jan 1, 1905

By H. L. B. Gould, Jr. Wenny D. H.

TO date there has been but limited interest in alloys of 80 to 95 pct Co and Fe with or without other additions. In 1932, S. R. Williams' reported practically zero magnetostriction for the 90 pct Co-10 pct Fe alloy. This same composition was used for pole pieces to control the magnetic field in magnetrons operating at high temperatures.' In 1947, a 90 pct Co, 9.5 pct Fe, and 0.5 pct Mn composition was investigated3 for use in ballast lamps because of its high temperature coefficient of resistance. Recently, as part of a survey of ductile and malleable magnetic alloys capable of being processed to thin gages for possible applications in memory devices, the high Co-Fe alloys have been re-examined to determine their fabricating and magnetic characteristics. Alloys from 80 up to 95 pct Co and Fe with and without additions such as vanadium were prepared. In general these all had excellent ductility and malleability. Wire was drawn to thin gages without difficulty and fine hard-drawn wires flattened to 2) The phenomenon may have potential in estimating the carbon content of molybdenum. A given solution-treating temperature and cooling rate could perhaps be calibrated so that the area fraction of surface covered by carbide could be interpreted in terms of carbon concentration. By segregating to the surface, a big "magnification" of the carbon content is obtained, which should make the method cheap, direct, and sensitive and, therefore, perhaps of interest to the molybdenum industry. This work was conducted at Battelle Memorial Institute. Financial support by the Aeronautical Systems Division, United States Air Force, under Contract No. AF 33(657)-7376, is gratefully acknowledged, and the writer is thankful for the experimental assistance of Miss Marjorie Cantin. ribbon without splitting. Similarly, strip was cold-rolled as much as 99.75 pct reduction to a 0.25 mil thickness without intermediate anneals. Samples of round and flat wire and foil, in the severely cold-worked and annealed states, were checked for magnetic characteristics. The alloys exhibited widely divergent magnetic characteristics depending on the processing and heat-treating procedures used in preparing the samples. Direct-current hysteresis loops showing the different magnetic characteristics of 90 pct Co, 9.5 pct Fe, and 0.5 pct Mn alloys are shown in Figs. 1 to 8 inclusive, while Figs. 9 and 10 show the loops for an alloy of 82 pct Co, 11.75 pct Fe, 5.6 pct V, and 0.65 pct Mn. Figs. 1 and 2 show the high remanence and exceedingly square-loop characteristics of the hard-drawn wire and ribbon roll flattened therefrom. With the change in processing from roll flattening to flattening by drawing through flat diamond dies the resultant change in texture is accompanied by the drastic change in the shape of the loop as shown in Fig. 3. This skewed loop on annealing reverts to a more normal loop as shown in Fig. 8. The most unique loops are obtained with flat rolled strip. These are shown in Figs. 4 and 5. In the case of the hard-rolled material, Fig. 4, there is little change in induction until the magnetizing force reaches 50 oe. From 50 to 60 oe there is a sharp increase in induction to over 15,000 gauss, which for all practical purposes is saturation. The induction remains at a constant value while the magnetizing force decreases to 40 oe. At this point the

Jan 1, 1965

By M. C. Leverett

The behavior of mixtures of immiscible liquids in porous solids is of rapidly increasing interest to those engaged in the production of petroleum. The operation of artificial water-floods and the control of natural ones immediately raise questions concerning the fundamental nature of such processes. Moreover, it is now recognized that often water occurs dispersed throughout the rock from which the oil issues into the well,' and thus tends to move toward the well simultaneously with the oil. The work reported here is a laboratory investigation of the simultaneous, steady-state flow of oil and water through the same column of uncon-solidated sand. It is thus directly related to the situation in which water occurs in oil-producing sands; it may have less direct implications for the displacement of oil from sands by water. However, it is to be clearly understood that the experiments to be described were performed primarily to obtain information of a more or less fundamental nature, and are not an attempt to reproduce, on laboratory scale, any part of an oil field. The dynamic behavior of a system in which oil and water are flowing simultaneously through sand is best described in terms of its "effective permeability" to either phase. For incompressible fluids flowing through a system of uniform cross section, the effective permeabilities to the two phases, in darcys, may be defined by the equations: Ko = PA6A [la] and Ku = Q [lb] In order to put the results obtained on a comparable basis for different sands, the effective permeabilities will be stated as fractions of the normal permeability of the sand; i.e., fractions of its permeability to a homogeneous fluid. Algebraically, these fractions are: KO' = Ko/K, and KWr = K,/X [2a] and [Zb]

Jan 1, 1939

By W. Griffith

The purpose of this paper is to make public record of new information in regard to the sustaining power of artificial mine-roof supports (not timber props), the result of investigations recently made in the anthracite coal fields of Pennsylvania. First.—By the "Scranton Mine Cave Commission," appointed to investigate the mining conditions under the City of Scranton. Second.—By the "Pennsylvania Mine Cave Commission," appointed by the Governor to investigate the general subject of mine caves in the anthracite region of Pennsylvania. Third.-—By the personal researches and tests made by the author in an effort to secure a better artificial mine-roof or surface support. During the progress of the work of the Scranton Mine Cave Commission, the Engineers for the Commission, Messrs. Conner and Griffith, being aware of the general lack of exact information in the engineering profession as to the strength of the ordinary artificial mine-roof or surface support, and particularly the stronger kinds, such as mine cogs, rock piers, etc., had tests made at the Fritz Engineering Laboratory at Lehigh University, to determine the sustaining power under various compressions of the several kinds of artificial mine supports in use in the anthracite region of Pennsylvania. A report of these tests wasincluded in the report of this Commission, which was published as Bulletin No. 25 of the United States Bureau of Mines, Washington. A similar series of tests, more extensive and more elaborately planned, were subsequently made for the Pennsylvania Minc Cave Commission at the U. S. Government Testing Laboratory at Pittsburgh, Pa. The report of this Commission was made to the Governor, but has not yet been published. The author, during his connection with the Scranton Mine Cave Commission, observed that of all the various devices employed for sustaining the roof of coal mines, the one universally used and the best

Jan 1, 1918

By M. C. Leverett

The behavior of mixtures of immiscible liquids in porous solids is of rapidly increasing interest to those engaged in the production of petroleum. The operation of artificial water-floods and the control of natural ones immediately raise questions concerning the fundamental nature of such processes. Moreover, it is now recognized that often water occurs dispersed throughout the rock from which the oil issues into the well,' and thus tends to move toward the well simultaneously with the oil. The work reported here is a laboratory investigation of the simultaneous, steady-state flow of oil and water through the same column of uncon-solidated sand. It is thus directly related to the situation in which water occurs in oil-producing sands; it may have less direct implications for the displacement of oil from sands by water. However, it is to be clearly understood that the experiments to be described were performed primarily to obtain information of a more or less fundamental nature, and are not an attempt to reproduce, on laboratory scale, any part of an oil field. The dynamic behavior of a system in which oil and water are flowing simultaneously through sand is best described in terms of its "effective permeability" to either phase. For incompressible fluids flowing through a system of uniform cross section, the effective permeabilities to the two phases, in darcys, may be defined by the equations: Ko = PA6A [la] and Ku = Q [lb] In order to put the results obtained on a comparable basis for different sands, the effective permeabilities will be stated as fractions of the normal permeability of the sand; i.e., fractions of its permeability to a homogeneous fluid. Algebraically, these fractions are: KO' = Ko/K, and KWr = K,/X [2a] and [Zb]

Jan 1, 1939

By Russell Gibson, F. S. Turneaure

The tin deposit of Monserrat, Bolivia, consists of one major vein 1600 m in length. The ore is unusual because of the notable quantity of teallite, even though cassiterite is the principal tin mineral. The deposit, formed at shallow depth under a wide range in temperature, may be classed as xenothermal. Polished sections reveal a complex history of replacement, with low-temperature minerals deposited before high-temperature minerals.

Jan 10, 1950

By C. H. Noren

For some years the Du Pont Company has utilized computer calculations to study the various theoretical properties of explosives. These studies have yielded valuable information on the effects of density changes or formulation changes on detonation rate, detonation pressure, explosion pressure, heat of explosion and numerous other properties, and have aided in evaluating the theoretical potential of explosives. In addition, a multitude of laboratory tests have been utilized for the evaluation of explosives. When comparing the computer data and the voluminous test data it became evident that numerous anomalies existed. Tests in rock were required to study explosives under borehole confinement. This fact was further emphasized after numerous field measurements showed that the borehole velocity of commercial explosives did not match the theoretical value but was dependent on conditions of field use. Since we are interested in the practical aspects of blasting, a program was initiated to evaluate explosives as used in commercial blasting. INSTRUMENTATION Most of you are familiar with the extensive work that has been done by the U. S. Bureau of Mines in their studies of strain measurements in rock. Early in our work we adopted procedures similar to those used by the Bureau of Mines. Strain pulses were measured by gages cemented in boreholes. Since we were primarily interested in the effect of explosives in the zone where fracture might occur, this system offered several disadvantages for Du Pont: 1. Cemented gages were expensive and not reusable. 2. When gage holes were used for several shots, there was considerable question as to the condition of the rock after the first shot.

Jan 1, 1968

By Frederick Laist

IT IS obviously impossible to design a copper smelting plant which could be considered, ideal under all conditions. For example, a plant properly designed to smelt the concentrates resulting from the treatment of porphyry ores by flotation would not be the kind of plant that one would design for the treatment of a coarse pyritous copper ore. The smelting of flotation or other fine concentrates is generally accomplished in a reverberatory plant, although occasionally the concentrates are sintered and then smelted in blast furnaces. On the other hand, coarse self-fluxing ores, whether pyritic or semi-pyritic, are generally smelted in a blast-furnace plant. Even this statement is only- approximately true, since the choice will be influenced by many factors; for example, the kind of fuel available (coal, oil or coke), the value of power (electric or steam), the uses to which waste steam may be put (heating, drying, etc.), the cost of refractories (silica and fire brick), the permanence and continuity of the ore supply and the relative first costs of the two types of plant (the reverberatory plant is generally more expensive to construct and to shut down), the contour of the site on which the plant is to be built (rugged, rolling or flat), the intelligence and character of the labor avail-able, and many other factors. From these remarks, it is evident that no copper smelter can be ideal for all conditions of ore and locality, and inasmuch as most of the copper now being pro-duced comes from fine or flotation concentrates and these are generally smelted in reverberatory furnaces, I shall confine my remarks to this type of smelt-ing plant.

Jan 5, 1923

By T. F. Archbold, P. G. McCormick

Silica fiber 11arkevs and hardness irzdentatiozs have been used to study the thermal diffusion of racancies in zinc placed in temperature gradients of 460o and 706oK per Cm All markers mored toward the higher temperatures, and the data show that the heat of trarlsport Q is greater than the eizthalpy of z,acancj3 forrjalion E by an amount equal to 3.5 kcal per mole. These results ore not in agreement with those obtained in either of the two previous studies with zinc. The problem is discussed in terms of experimental differences and racancy source and sink efficiencies. THE general interest in thermal-diffusion phenomena over the past several years has prompted a number of marker movement studies using pure metals. In order to understand better the relationships between thermal and mass flow, a general goal of the experiments has been to obtain values for the net enthalpies carried by the diffusing atoms. For self-diffusion by means of the vacancy mechanism, the determination of relative marker positions before and after an anneal in a temperature gradient permits a calculation of a value for (Q - Ef). Q is the transferred enthalpy, and Ef is the enthalpy of vacancy formation in the metal being investigated. The initial experimental study of thermal diffusion in pure metals was accomplished by Shewmon who found essentially no movement of surface-hardness indentation markers in single and bicrystals of zinc held for 20 days in a temperature gradient of 310°C per

Jan 1, 1967