Search Documents

By R. J. Hafsten, E. S. Davenport, R. A. Grange

THE influence of austenite grain size upon the hardenability of steel is now fairly well understood; for a given austenite, increasing the grain size increases the depth of hardening, and, since the latter is related to the fundamental transformation behavior of austenite, it follows that austenite decomposition must, in general, be retarded by increasing grain size. To date, very little quantitative information bearing directly on the effect of austenite grain size upon the progress and result of isothermal transformation has been published. Davenport and Bain,1 and Zimmerman, Aborn and Bain2 have shown that the transformation is definitely retarded in hypereutectoid plain carbon steels at temperatures near and above the upper region of rapid transformation (Ar') when the austenite grains are increased in size. More recently, Griffiths, Pfeil and Allen3 investigated the effect of a series of different heating (austenitizing) temperatures upon the progress of isothermal transformation at 1245°F. (675°C.) and 745°F. (395°C.) in a medium carbon, low-alloy steel; while they reported no measurements of the austenite grain size, their results suggest that increase in grain size retards austenite transformation at 1245°F. (675°C.), but has no appreciable effect at 745°F (395°C.). The present paper deals with the results of a study of the isothermal transformation of austenite in a single commercial alloy steel in which a fine-grained or a coarse-grained state was induced by appropriate selection of austenitizing temperature. The data are presented in the form of isothermal transformation diagrams, which clearly show that coarsening the grains lessens the rate of transformation of austenite to proeutectoid ferrite and pearlite-that is, at temperature levels above about 1000°F. (540°C.)-but is without significant effect at lower temperatures where the transformation product is bainite or martensite. It is to be presumed that the foregoing statement would be valid, at least in principle, for many other grades of steel; it confirms again that the mechanism of transformation to a pearlitic structure is fundamentally different from that to an acicular structure. A number of related observations were made, which seem to throw some light on the transformation process as it takes place in alloy steels, particularly at temperature levels in the vicinity of 1000°F. (540°C.), where the transition from lamellar to acicular structures occurs. These data are discussed briefly in the belief that they may lead to a clearer understanding of this aspect of the subject. MATERIAL AND EXPERIMENTAL PROCEDURE The material investigated was a commercial grade of S.A.E. 4140 steel, the composition of which was as follows: 0.37 per cent C, 0.77 per cent Mn, 0.98 per cent Cr and 0.21 per cent M0. It was hot-rolled to a 1 1/8-in. round bar and normalized by air-cooling from 1800°F. (980°C.).

Jan 1, 1941

By K. Takahashi, I. Iwasaki

it is well known1 that racemic mixtures of optical isomers can be separated by passing their solutions through a column packed with r- or 1-quartz powder so that one of the isomers becomes adsorbed selectively on the asymmetric quartz surfaces. Although the natural occurrence of r- and 1-quartz is more or less equally distributed, some localities show enough deviations toward a higher proportion of l-quartz2 to suggest that optical isomerism might influence quartz flotation. Beta-amines have an asymmetric carbon atom, and therefore optical activity may be expected. Beta-amines are reported to behave quite differently from alpha-amines in the flotation upgrading of certain oxidized iron ores.3 It is of interest, for both practical and theoretical reasons, to determine whether or not optical isomerism plays a role in the amine flotation of quartz. In this article the results of Hallimond tube flotation tests and of adsorption measurements using d-beta-phenylisopropylamine on both r- and 1-quartz are compared. D-beta-phenylisopropylamine was chosen for the tests because it is commercially available in optical isomers. MATERIALS AND METHODS Brazilian quartz crystals were hand-sorted according to the difference in trigonal trapezohedral faces, and each crystal was further checked by the Airy's spiral.4 The respective crystals were then crushed, and the -150 + 200-mesh fractions were screened out for the Hallimond tube tests. The samples were cleaned by brief leaching with warm, dilute hydrochloric acid, and then by repeated rinsing with distilled water. In preparation for the adsorption measurements, they were then dry-ground in a pebble mill for several hours, washed a few times with distilled water, and finally dried in a vacuum desiccator. By means of the Krypton gas adsorption method, the specific surfaces of r- and 1-quartz samples were determined to be 27,700 and 19,800 sq cm per gm respectively, the difference being due mainly to the decantation procedure rather than to the inherent difference in their grindability. D-beta-phenylisopropylamine was the only collector used in the study. It was solubilized by neutralizing with 110% of the stoichiometric requirement of 0.1 N hydrochloric acid. The specific rotation of the d-beta-phenylisopropylamine was determined with a polari-meter using sodium D line to be, Although the d-beta-phenylis~prop~lamine showed absorption maxima in the wave length region of 250 to 270 millimicrons, due presumably to the phenyl group, these peaks were too sensitive to be used for colorimetric determination of the residual concentration in the adsorption measurements. The amine-picrate method, used in the colorimetric analysis of dodecylammonium chloride,' was found to work satisfactorily for the d-beta-phenylisopropylamine. The adsorption densities were thus determined after equilibrating 40 gm of the ground quartz sample with 300 ml of solution by tumbling in separate glass-stoppered Erlenmeyer flasks for one hour. EXPERIMENTAL RESULTS Fig. 1 presents the adsorption densities of d-beta-phenylisopropylamine on the r- and 1-quarts in the pH range of 6 to 7.5. In agreement with data reported in the literature, the adsorption density of d-beta-phenylisopropylamine was slightly higher on the r-quartz than on the 1-quartz, although the difference was not as pronounced as one might expect from the capacity of r-quartz and 1-quartz to separate racemic

Jan 1, 1969

By AIME AIME

NO FEATURE of the annual meeting is considered more important at Institute headquarters than the assembly of delegates from the various local sections and divisions. There the president of the Institute and other officials may learn at first hand what the members are thinking and doing in every part of the country, and the delegates, in turn, may find that head- quarters is not a group of more or less cold-blooded New Yorkers whose primary function is to send out annual bills for $15. This year, the section and division delegates required three sessions to thresh out the matters of common interest: Monday morning and afternoon and Thursday afternoon. They were also guests of the Institute at the Directors' dinner on Tuesday night, and at the Directors' meeting afterward.

Jan 1, 1932

By F. A. Seward

A1though the expanding Eltran1 configuration has been used in induced polarization exploration for several years, there has been little application of this method to straight resistivity problems. A comparison of results of resistivity exploration by this technique versus those obtained from Wenner configuration surveys reveals a number of advantages in interpretative resolution as well as in field operation. The application of electrical resistivity to ground-water exploration is well known.= In the past a major portion of this work has been accomplished by use of one or more variations of a technique employing the Wenner3 electrode configuration. With the introduction of the frequency domain technique of induced polarization measurements, used primarily in the exploration for disseminated sulfide deposits, there arose the need for an electrode configuration by which potentials could be measured externally to the current electrode spread in order to minimize coupling between current sending and potential receiving circuits. It was also deemed desirable that the configuration would provide information laterally along profile as well as with depth. To reach these objectives the expanding dipole-dipole configuration (which probably first was used in the electrical transient method of exploration and from which the name 'Eltran' was derived) has been adapted to induced polarization exploration. The author has successfully applied the same techniques

Jan 1, 1963

By William C. Buell

As used in connection with open-hearth or other high-temperature operations, "insulation" refers to a multitude of substances, natural or manufactured, that have the one principal property of preventing the flow of heat by conduction to a greater degree than refractories can prevent it, the principal properties of the latter being resistance to temperature and/or chemical action. The term "control" as commonly applied to the mechanization of management functions is inappropriate without qualification, for without some degree of control of every operation we could produce no steel worthy of the name. Although grouped together in this paper, insulation and control in open-hearth furnaces have little, if any, interrelationship, therefore the paper is made up of two distinct parts. INSULATION OF OPEN-HEARTH FURNACES More than ten years ago the writer proposed the insulation of an acid open-hearth furnace system below the charging floor, and it was accomplished, with gratifying results. Possibly that was the first time the insulation of regenerators and slag pockets of any open-hearth furnace was undertaken, but shortly thereafter such insulation became general, and when the six groups of 150-ton furnaces1 were built in 1929-1930, they were completely insulated below the charging floor. While the practice was accepted at least five years ago, it was not well understood, however, as indicated by the following incident which occurred in connection with an installation made in 1929. After the

Jan 1, 1935

By William C. Buell

As used in connection with open-hearth or other high-temperature operations, "insulation" refers to a multitude of substances, natural or manufactured, that have the one principal property of preventing the flow of heat by conduction to a greater degree than refractories can prevent it, the principal properties of the latter being resistance to temperature and/or chemical action. The term "control" as commonly applied to the mechanization of management functions is inappropriate without qualification, for without some degree of control of every operation we could produce no steel worthy of the name. Although grouped together in this paper, insulation and control in open-hearth furnaces have little, if any, interrelationship, therefore the paper is made up of two distinct parts. INSULATION OF OPEN-HEARTH FURNACES More than ten years ago the writer proposed the insulation of an acid open-hearth furnace system below the charging floor, and it was accomplished, with gratifying results. Possibly that was the first time the insulation of regenerators and slag pockets of any open-hearth furnace was undertaken, but shortly thereafter such insulation became general, and when the six groups of 150-ton furnaces1 were built in 1929-1930, they were completely insulated below the charging floor. While the practice was accepted at least five years ago, it was not well understood, however, as indicated by the following incident which occurred in connection with an installation made in 1929. After the

Jan 1, 1935

By P. A. Flinn

ALTHOUGH many physical properties of superlat-tices have been studied intensively, relatively little attention has been paid to their mechanical properties until recently. Even for the well-known transformation in 0 brass, the effect of the transformation on plastic behavior has only lately been extensively investigated.''' A partial analysis of dislocation structure in superlattices has been given by cottrel13 and his theory agrees well with the experimental results on CU3AU.4,5 His analysis, however, is implicitly limited to low-temperature effects, since it does not include the behavior of dislocations at temperatures high enough for diffusion, and hence climb, to occur. The work of Herman and Brown2 on the creep of 0 brass indicates that important effects occur under such conditions, and consequently, the theory should be extended to include them. Such high-temperature effects cannot be observed in Cu3Au, since it disorders below the temperature at which diffusion occurs at a reasonable rate. There are materials of the same structure, however, such as Ni3A1, which retain their order up to, or close to, the melting point. GEOMETRY OF THE COMMON SUPERLATTICES The two best-known ordered structures are the 0 brass type, B2, shown in Fig. 1, and the Cu3Au type, Ll2, shown in Fig. 2. In the B2 structure the (000) and (1/2, 1/2, 1/2) sites are different in that they are occupied by different types of atoms. The symmetry of the structure is then lowered from a body-centered cubic, A2, in which the sites are equivalent, with atoms located randomly in the sites, to simple cubic. This lowering of symmetry has the consequence that two types of regions may occur within a crystal: regions where A atoms are in the (0, 0, 0) sites, and regions where they are in (1/2, 1/2, 1/2) sites. The boundary between two such regions will contain bonds between like atoms, and be a surface of higher energy. These regions are known as antiphase domains and the boundary as antiphase boundary. In the B2 structure, boundary formed during the ordering process should disappear as a result of domain growth, since any domain growing to the boundary of two others will join one and engulf the other.' In any well annealed crystal, only a single domain should exist, with antiphase boundary present only in connection with dislocations, as discussed below. The L1, structure is related to the A1 (face-centered cubic) in much the same way as the B2 is to the A2. The face-center sites are occupied by A atoms, and the corner sites by B atoms. The symmetry is again lowered to simple cubic, and antiphase domains can exist. In this case, however, there are four initially equivalent sites in the unit cell: (0,0,0), (0, 1/2, 1/2), (1/2,0, 1/2) and (1/2, 1/2, 0). In the ordered structure any one may be occupied by a B atom and the other three by A atoms. Thus four types of antiphase domains can occur in this structure. This is sufficient to permit a metastable "foam structure" to exist within a crystal.''7 Antiphase boundaries along three different planes are shown in Figs. 3, 4, and 5.* *The presence of a layer of disordered material between antiphase domains, as suggested by Jones and Sykes8 does not seem likely. Such a layer would be a region of unnecessarily high energy which could readily be reduced by the formation of the type of boundary discussed here.__________________________________________________________ The notation (111) [110] means a boundary lying along a (111) plane between antiphase regions related by a 1/2 [I10] translation. It may be seen in Figs. 3 and 4 that an antiphase boundary usually results in incorrect nearest neighbors (shown connected by braces). However, as pointed out by Wilson, a boundary of the (001) [I101 type can exist

Jan 1, 1961

Albert Arents, Alameda, Cal.: From Mr. Furman's description of his crucible-assays I infer that he regards iron nails as a necessary or advisable adjunct. Against such a notion I must beg leave to protest. Nails should not be used in

Jan 1, 1896

By AIME AIME

On Nov. 11, 1909, M. Alexandre Pourcel, of Paris, France, upon the proposal of a large number of distinguished members, and the unanimous recommendation of the Council, was elected by the Board of Directors an Honorary Member of the Institute. M. Pourcel has devoted forty-three years to the metallurgy of iron and steel ; and the work which he did between thirty and forty years ago constitutes an important part of the founda¬tion of the practice of to-day. Among his striking contribu¬tions are : (1) his perfection, in 1869, of the manufacture of high-grade ferro-manganese in a carbon-lined open-hearth furnace, instead of the costly crucibles previously used; (2) his discovery, in 1874, of the method of making solid steel cast¬ings; (3) his manufacture, in 1875, of ferro-manganese and silico-spiegel in the blast-furnace; and (4) his anticipation, in 1875, of modern American blast-furnace practice, by the pro¬duction, in a very small furnace, of Bessemer pig containing 2.5 per cent. of silicon, from a burden yielding only 46 per cent. of iron, and with a consumption, per ton of pig, of only 1,8401b. of coke, containing 15 per cent. of ash. These brilliant pioneer achievements, together with his contributions to cur¬rent technical literature, won for him the Bessemer gold medal of the Iron and Steel Institute ; the great" medal of honor," which is the highest award of the French Society of Mineral Industry, and other gold medals, as well as the distinction of honorary membership of the Comité des Forges de France, which was conferred upon him in 1891. In recent years, M. Pourcel has been instrumental, as consulting engineer of the Société de Commentry-Fourchambault, at Decazeville, France, in an extraordinary development of the manufacture of special steels. The Invar plant, of this company, is said to make a greater variety of such steels (includ-

Dec 1, 1909

By Ionel I. Gardescu

During the summer of 1930 the average daily oil production of Rumania registered a new peak at 128,000 bbl. per day. The estimated potential production as of September, 1930, was as high as 235,000 bbl. per day. During the latter part of the year, by mutual agreement, the operators decided to curtail their output to about 100,000 bbl., which brought the average for the year to 116,600 bbl. The total production for 1930 was 41,572,000 bbl. (last month estimated) as compared with 35,757,000 bbl. for 1929, or an increase of 16.3 per cent. over last year's production. The production for the last 10 years is given in Table 1. The curtailment of production was prorated per company, based on its total estimated potential production as of September, 1930, and not per field. As a consequence, at present there is little development of protected or slightly productive areas; viz., Arbanasi, with an average production of 1750 bbl. per day, dropped to less than one-third after curtailment came into effect. Moreni, with an average production of 92,000 bbl. per day, while producing 58 per cent. of the country's total output in 1929, went to 67 per cent. at the beginning of 1930 and to 75.2 per cent, towards the end of the year. The modified Mining Law of 1929 is still in effect. This law withdraws the restrictions set on foreign capital by the law of 1924. As a consequence a large percentage of proven state land was alloted through competitive bidding to foreign companies. The Romano-Americana (Standard of New Jersey) acquired several leases in the Boldesti and

Jan 1, 1931

[ ] Granville S. Borden (Mining Taxation, P. 1049) has written two other published articles on the subject, Taxation and Mineral Resources, and An Income Tax Program for Mineral Producers. Both articles appeared in Mining Engineering. He is presently employed by Standard Oil Co. of California as a special tax counsel. He holds an LL. B and an LL. M from George Washington University and a Bachelor of Science in Mining from the University of California. He has been chairman of the Taxation Committee of the Minerals Economics div. of the AIME. Borden fishes, plays golf, prospects, and performs mineral analysis as hobbies. [ ] Charles C. Towle (co-author, Uranium Deposits of the Grants District, New Mexico, P. 1037) graduated from the Colorado School of Mines with a degree in Geological Engineering. He was a member of Sigma Nu; Theta Tau, an honorary professional society; Blue Key, honorary social society; the glee club and quartet, and a member of the student council. He has been a mucker, driller, flotation operator and mill shift boss for the Clear Creek-Gilpin Co., Idaho Springs, Colo.; Geologist, chief engineer, and chief geologist for Patino Mines & Enterprises Consolidated, Inc., Bolivia; appraisal engineer and part-time geology student, Denver; office geologist for Geology Dept., special Engineering div., Sea Level Canal Studies, Panama Canal; and geologist, div. of Raw Materials, USAEC, Grand Junction, Colo. He is currently chief of the Denver Exploration Branch, div. of Raw Materials, USAEC, Denver. Towle was at one time a tournament golfer, playing three and four times a week. While working in South America he played in numerous tournaments. Today, although playing only occa sionally, he shoots in the low eighties.

Jan 1, 1952

By AIME AIME

IN A STATEMENT summarizing general conditions in the Federated American Engineering Societies, the executive secretary, L. W. Wallace, expresses the belief that the Federation has made substantial progress. At the annual meeting of the American Engineering Council, to be held in Washington Jan. 5 and 6, this progress will be shown by reports covering activities in many fields. "Unquestionably," says Mr. Wallace, "the Federa¬tion has made favorable and permanent contacts in Washington. Through the, activities of Congress and of the new Federal administration. we have had the opportunity to render some really constructive service. We feel, however, that the great body of engineers are not adequately informed of the organization of the Federation, of its aims and purposes and of its activities.

Jan 1, 1921

By Ronald W. Utley

INTRODUCTION The ''Do's and Don'ts" of installing equipment in a comminution circuit begin during the study stage of a proposed project, continue through preliminary engineering, detail engineering, procurement, the actual placement of equipment at the job site, and end with turnover to the owner. Equipment supplied for a modern comminution circuit will be high quality, rugged machinery designed according to appropriate manufacturing standards for long hours of trouble-free service. However, certain precautions and procedures must be observed in plant design and layout, equipment handling, installing and servicing in order to obtain optimum performance. This chapter contains general installation "DO'S and Don'ts" for the major equipment in the circuit. •Primary Gyratory Crushers •Rock Breakers (Hammer) •Belt Conveyors •Apron Feeders •Weigh Belt Scales •Secondary Crushers •Vibrating Screens •Grinding Mills •Mill Liners •Open Gear Sets •Speed Reducers •Electric Motors •Cyclones •Slurry Pumps Some questions will not be covered in this chapter, or may not be applicable to the actual equipment purchased, as requirements do vary from manufacturer to manufacturer. Additional specific information can be obtained by contacting the manufacturer's local representative or the factory. All inquiries should be accompanied by the following information: •Unit size and type of equipment •Manufacturer's shop order number (after order placement) •Serial number (after manufacture) DO'S 8 DON'TS FOR INSTALLATION OF ALL COMMINUTION CIRCUIT EQUIPMENT Installation By Design DO obtain tables of weights and clearances from manufacturer. DO obtain WR2 forces from manufacturer to determine that the foundation is adequate. DO determine compression strength of foundation soil and/or rock. DO obtain manufacturer's recommended typical foundation drawings. If substantial alteration to manufacturer's drawings is required, check with the manufacturer before proceeding.

Jan 1, 1982

By P. Shahinian, H. H. Smith, M. R. Achter

Crack growth rates are measured at elevated temperature in a resonant fatigue machine from vibration frequency decreases calibrated in terms of crack depth. Crack growth rates in Type 316 stainless steel at 500º and 800°C show a sharp increase with oxygen pressure in an intermediate pressure range and little or no change at high and low pressures. At 500°c, I torr of oxygen reduces the fatigue life by almost a factor of 100 in comparison to that in vacuum and raises the growth rate of shallow cracks by the same At At 800°C the effects are smaller. Changes in slope in the crack growth rate curves are discussed in terms of a model in which rates of surface production and of surface coverage by gas are compared. The use of a calculation method in which the surface exposure time is equal to X/v, where x is the interatomic spacing and v is the growth rate, makes it possible to obtain order of magnitude agreement at 500°C between the observed pressure and the predicted pressure at these slope changes. At 800°C oxidation becomes a .factor and the data cannot be treated by simple adsorption theory. THE decrease in the fatigue life of metals as a function of gas pressure usually follows a stepped curve with virtually all of the decrease concentrated in a sharp drop in a transition zone at intermediate pressures and little or no change at low and high ranges. A number of models, differing in the details of the mechanism, have been offered to explain the shape of the curve. Measurements of crack growth in aluminum as a function of gas pressure by Bradshaw and Wheeler' and Hordon2 demonstrated opportunities for quantitative comparison to evaluate the proposed models. Since comparable data were lacking at high temperatures, in the present work rates of crack propagation were measured in Type 316 stainless steel at 500" and 800°C as a function of oxygen pressure. Choice of this material was dictated by two considerations; it is stiff enough at these elevated temperatures to resonate with the regenerative drive on our fatigue machine and it is known to display a large effect of environment. A new method of calculation is described to predict the gas pressure at the critical point. EXPERIMENTAL PROCEDURE Because of the difficulty of measuring crack depths directly at high temperatures, an indirect method was developed based on the decrease in the resonant frequency with the growth of a crack. A reversed bending, constant amplitude fatigue machine, described previously,3 vibrates a specimen at its resonant frequency, automatically records any changes in it and shuts itself off after it has reached a preset value of frequency decrease. The record of frequency change is used to determine the rate of crack growth. Sheet type specimens of Type 316 stainless steel, Fig. 1, incorporated a sharp, shallow notch to localize the formation of a single crack. After machining, they were annealed in a vacuum of l0-6 torr either at 1066" (lot A) or 871°C (lot B) and then electropolished in an acetic-chromic acid solution. Bending strains were measured at 500" and 800°C by an optical technique4 and reported as total strain without correction for the notch. At 500°C, the 0.141 pct strain was 0.085 pct elastic and the remainder plastic. At 800°C the 0.062 pct strain was all elastic. To convert frequency decrease to crack length, calibration curves were obtained by interrupting the vibration at stated intervals of frequency decrease. The crack depth was measured microscopically at a magnification of X400 and reported as the average of the measurement on each edge. Some specimens were sectioned for crack measurement while others were returned to the machine and fatigued further. There was good agreement between the two methods. Before beginning the vibration, the vacuum chamber was first evacuated cold to 1 x 1O-6 torr, then heated to the operating temperature and held there until the pressure was again reduced to 1 x10-6 torr at which time oxygen was introduced to the desired pressure. In this investigation the vibration frequency was nominally 10 cps and a decrease of 0.6 cps was taken as the failure point. The choice of the frequency decrease to represent failure has no appreciable effect on the fatigue life because the crack is growing very fast at this point.

Jan 1, 1970

By H. F. Bishop, F. A. Brandt, W. S. Pellini

The solidification mechanism of experimental steel ingots (7x7x20 in.) was studied by thermal analysis. It was determined that solidification proceeds in wave-like fashion at rates which are determined by the carbon level, superheat, and mold thickness. The thermal cycles of the mold walls were related to the course of solidification. ESPITE marked advances in the field of solid state transformation, metallurgical research has contributed comparatively little exact quantitative data on the mechanism of solidification of metals. There is, therefore, a great need for such data in the various metallurgical industries. The mechanics of solidification of ingots have been investigated in the past primarily by studies of the rate of skin formation as indicated by bleeding or "pour out" tests. The "pour out" method, however, is a tool which gives only approximate information. In the case of alloys with wide solidification ranges, such as irons and certain nonferrous alloys, the method will not work at all; in the case of alloys of intermediate solidification ranges, such as commercial steels, the information may be misleading. Thus, the general adoption of this method has resulted in divergent conclusions regarding the solidification process. Chipman and Fondersmith1 by means of bleeding tests have shown that the linear growth of a solidifying ingot wall follows a parabola of the general form, D = K C, with the start of solidification delayed until superheat is exhausted, as indicated by the constant C. These tests were carried only to a wall thickness of about 5 in. using an ingot of approximately 17x39 in. in cross-section; hence the latter stages of solidification were not studied. Matuschka2-3 indicated that linear solidification of ingots is rapid at first, then slow, but toward the end of solidification the rate becomes extremely rapid again. Spretnak's4 bleeding studies indicated that, wall growth is expressed more rigorously by two parabolas, and that their point of intersection corresponds to a change of solidification mode from columnar to equiaxed. Spretnak also showed that the K values of the first parabola are always the same regardless of superheat. Nelson bled ingots of square cross-section and found that linear wall growth is initially rapid but decreases continually until the end of solidification. He also concluded that rate of solidification in ingots of square cross-section increases 2.15 pct for every 10 pct increase in cross-sectional area of the mold. The mold ratios considered (ratio of cross-sectional area of the mold to cross-sectional area of the ingot) were all less than 2 to 1. The subject of solidification has also been treated mathematically in many cases, but because of the lack of accurate thermal constants and the simplifying assumptions required, as their authors generally acknowledge, they represent only approaches to the actual conditions of ingot solidification. A third method of studying solidification is the electrical analogue method promulgated by Pasch-kis6-7 and by Jackson and coworkers.8 This method treats solidification as a heat transfer problem with the solidification cycle synthesized on an electrical circuit. Paschkis in his treatment of solidification considered the fact, which was generally ignored, that solidification of steel is not simply the growth of a plane solid wall but a more complex process occurring over a temperature range as indicated by the constitution diagram. Undoubtedly, the anomalous results obtained by bleeding tests arise from the inability to measure quantitatively this mushy condition. The shape of Paschkis' solidification curves are more nearly in accord with those of Matuschka, in that they indicate rapid linear solidification at the beginning and end of solidification with intermediate solidification occurring at a slower rate. Paschkis indicates a definite lengthening of solidification time with increasing superheat. Thermal analysis is a direct method providing exact information for all types of metals regardless of solidification range and was thus adopted in the present program to follow the entire course of solidification from the surface to the centerline of the ingots. The method has the added advantage of being adaptable to following the thermal cycle of the ingot mold during the course of solidification. Test Methods The ingots studied were of square cross-section, 20 in. long, tapered from 71/4 in. at the top to 63/4 in. at the bottom, and fed with a hot top 7 in. in diam and 12 in. high. The molds were uniform in wall

Jan 1, 1953

By J. M. Woodall

GuAs crystals which have been grown in quartz boats by the horizontal Bridgman method in the pvesence of Ga20 vapov have beetz found to have carrier and donor distributions which do not correspound to those expected from simple dopant seg-vegation during directional freezing; Instead, the carrier distribution is determined by the heat-trentnzent history of the crystal, while the donor distribution, zohiclz is principally due to silicon, is fixed by the pozuth rate, the geo)tlet.ry of the crystal growth vessel, and tlze initial Ga20 pressure. WHEN semiconducting materials are made into doped crystals by the normal freezing method,&apos; they usually exhibit doping variations along the growth axis. If a) there is no dopant diffusion in the solid, b) the dopant is distributed uniformly in the melt, and c) the distribution coefficient, k, does not vary with composition, then the doping variation along the growth axis is represented by the equation: where C is the doping level in the solid at a point where a fraction g of the original liquid has frozen, and Co is the mean concentration. When the dopant is either a singly ionized shallow donor or shallow acceptor, C also represents the carrier concentration. Even though this equation accurately describes the dcping profiles of a large number of normal freeze systems, there are several special systems for which Eq. [I] does not apply. One such system is the horizontal Bridgman method for preparing oxygen-grown GaAs crystals using quartz vessels. Several workers2"* have shown that GaAs crystals grown by the horizontal Bridglnan method using quartz vessels are generally contaminated with silicon in concentrations in excess of 5 < 10lG atoms per cu cm. This contamination is ascribed to a reaction: occurring at the walls of the crystal-growth vessel which liberates silicon into the melt and Ga2O vapor. It has been shown4 that this reaction, and, hence, the silicon contamination, can be suppressed by the addition of oxygen to the crystal-growth apparatus. It is the purpose of this paper to describe a special apparatus capable of yielding single crystals of GaAs grown in the presence of oxygen and to describe both the kinetics of silicon suppression in this system and the relationship between the carrier concentration profile and the silicon concentration profile. EXPERIMENTAL-CRYSTAL GROWTH A schematic diagram of the apparatus used in the oxygen addition experiments is shown in Fig. 1. The most important features of this apparatus are: a) the use of a sand blasted quartz boat, h) a quartz rod of length 1, with a hole of cross section A, that is placed near the boat to limit the free space volume V, over the melt during the growth, and c) the temperature gradient at and near the solid-liquid interface. Sand blasting the boat is necessary to prevent wetting of the melt. The quartz rod retards the diffusion of the GazO vapor away from the melt to the colder portions of the ampoule. A crystal is prepared by first loading a 5.5-in. boat, which has been cleaned in aqua regia, with 40 g of 99.9999 pct Ga along with 1 to 8 mg of Ga203 powder. GazO3 is a convenient source of oxygen since it reacts with gallium at the melt temperature to form Ga20 vapor, the species which apparently controls the suppression of silicon contamination. The loaded boat, the quartz rod, and the 99.9999 pct As are placed in the ampoule as shown in Fig. 1. Generally, GaAs seeds were not used since most of the unseeded growths resulted in monocrys-tals. The ampoule is evacuated to 10-5 Torr and sealed off. The GaAs melt is synthesized by placing the ampoule into a two-zone horizontal Bridgman furnace. The two zones are separated by several sandwiched layers of -in. Fibre-Fax board drilled with holes slightly larger than the OD of the ampoule. This causes a very large temperature gradient between the two zones, which is necessary for single-crystal growth. The two-zone furnace is mounted on a stand fitted with a roller bearing which allows uniform motion of the furnace in a horizontal direction. A uniform velocity of the stand is achieved by the use of a windlass device which winds up a wire attached to the stand. Movement of the solid-liquid interface is accomplished by fixing the position of the ampoule and moving the stand. Growth rates investigated in this experiment were between 0.4 and 1.2 in. per hr. The composition of the melt is fixed by maintaining an arsenic reservoir at 618°C. The stand is moved away

Jan 1, 1968

By Charles H. Grant

Some of the limiting factors relative to explosive crushing of rock and ways to overcome a few of these problems are presented. Relationships between borehole diameters, bench heights, and spacings, along with a review of the influence geometry has on energy as these are changed, are discussed. Efficiency in use of explosives and the decay of energy as it moves through rock and is absorbed and dissipated, is described, along with fragmentation as a function of spacings and energy zoning, etc. Communications are one of the major problems encountered. In an effort to provide a better understanding of the use of explosives, it is necessary to take a little different view of what explosives are, how to look at them as tools to fragment rock, and some of the problems encountered in doing so. First, take the explosive: although there are many factors involved, consider these as being reduced to only two — shock-strain imparted to the rock by the high early development of energy, and the gas effect which is a combination of heat, moles of gas formed, rate of formation of these gases which develop pressures, etc. First, consider shock energy by itself and assume there is no gas effect in the reaction. Fig. 1 illustrates a block or cube of rock, in the center of which is detonated an explosive charge which is 100% shock energy. Tensile slabbing would be seen on the surface and probably the cube of rock would generally hang together even though microcracks were formed. If the situation is reversed and an explosive whch has no shock energy and only gas effect (Fig. 2) is considered, the cube of rock would act as a pressure vessel and contain the pressure from the gas effect until it exceeded the rock-vessel strength; then the rock would break in a few large pieces. If these two kinds of energy are put together and the area of shock-strain around the explosive (Fig. 3) is considered, the two energies will be seen working together to furnish broken rock. The gas effect applies pressure to the microcracks formed from the shock energy to weaken the rock-pressure vessel and propagate these cracks to break the rock apart. It not only will be broken more finely, but will break apart at a lower pressure than the gaseffect case, since the shock energy has first weakened the rock vessel. Although tensile spalling from the shock-strain imparts momentum to the rock, the main source of displacement comes from the gas effect. The term "rock" is being used to mean any material to be blasted. These energies are absorbed by the rock in different ways. First, classify rock into two main categories: "elastic" and "plastic-acting." Elastic rock should be thought of as rock which can transmit a shock wave and is high in compressive strength, such as granite or quartzite. Since this elastic rock transmits a shock wave well, it makes good use of the shock energy from the explosive-forming cracks, etc., for the gas effect to work on. Plastic-acting rocks are rock masses which are relatively low in compressive strength and absorb shock energy at a much faster rate, thereby making poor use of the shock energy by not developing as extensive a cracked zone for the gas effect to work on. Rocks of this type are generally softer materials such as some limestones, sandstones, and porphyries. For the most part, the shockenergy part of the explosive reaction is wasted in plastic-acting rock, leaving most of the work to the gas effect. Since the ratio of gas effect to shock energy is different in different explosives, it is easy to understand why some explosives perform well in elastic rock and poorly in plastic-acting rock, and vice versa. Some of the most difficult blasting situations arise when mixtures of plastic-acting and elastic rock are encountered (Fig. 4). Fig. 4 shows an example of granite boulders cemented together with something like a decomposed quartz monzonite which is plastic-acting. The elastic granite boulders will transmit the shock-strain within itself, but when this shock tries to move through the monzonite to the next boulder, its intensity is absorbed by the monzonite and little shock-strain is placed on the adjoining boulder. In addition to this loss by absorbtion, shock reflection at the surface of the boulder will effect tensile spalling. The net effect is poor breakage of the boulders which do not have drillholes in them as they simply will be popped out with the muck. The same is true (Fig. 5) when layers and joints make

Jan 1, 1970

By O. F. Kammerer, W. E. Miller, D. H. Gurinsky, J. Sadofsky, J. R. Weeks

Zirconium and titanium inhibit solution mass transfer of steels by liquid bismuth, mercury, and lead. It is shown that in bismuth and mercury, these adsorb on the surface of the steels and subsequently react with nitrogen and possibly carbon from the steels to form inert, adherent surface layers of ZrN, TiN, or TiN + Tic. Data are presented which describe the condition under which thase deposits form. These inhibitors decrease the solution rate of iron into bismuth, and require a higher supersaturation for precipitation of iron from bismuth. USE of the low-melting heavy metals (bismuth, lead, mercury, and their alloys) as coolants has been limited because solution mass transfer of steels occurs in these liquids; i. e., iron dissolves in the hot sections of the heat transfer circuit and deposits in the colder sections. The rate of solution of iron and the temperature coefficient of solubility are sufficiently great to cause complete or partial stoppage by the deposition in the coldest section of a closed circuit in finite time, even though the actual solubilities are extremely low. In the development of the mercury vapor turbine by the General Electric Co., Nerad and his associates1 discovered that the addition of as little as 1 ppm Ti or Zr to magnesium-deoxidized mercury reduced the mass transfer of ferrous alloys by mercury to a negligible amount. Reid2 reported that titanium was detected chemically on the surface of steels contacted with this mercury alloy in amounts varying from 2.0 to 2.6 mg per sq in., the greatest amount being found in the hottest portion of the circuit. Reid stated that the titanium forms the intermetallic compound Fe2Ti by reaction with iron on the surface of the steels. This compound was presumed to be highly insoluble in mercury. More recently, El-gert and Egan3 have reported a greater than 100-fold reduction in the rate of mass transfer of a 5 pet Cr steel by liquid bismuth upon the addition of titanium (in excess of 50 ppm) and magnesium (350 ppm) in the liquid metal, during experiments performed in thermal convection loops* over the temperature differential 700° to 615° C. Also, Shep-ard and his associates&apos; have reported that the addition of titanium to liquid bismuth and Pb-Bi eutec-tic produced a marked decrease in the rates of solution of both iron and chromium from type 410 steel capsules under static conditions. This inhibiting effect increased with repeated reuse of the capsules. Tests performed in this laboratory under carefully controlled conditions have shown that the addition of zirconium and magnesium, or titanium and magnesium, to liquid bismuth or lead greatly reduces the rate of mass transfer of chromium alloy steels and carbon steels in thermal convection loops with a maximum temperature of 550°C.5-9 The present paper will review the data obtained to date at this laboratory on the behavior of iron and steels in contact with liquid bismuth alloys containing titanium or zirconium, and will attempt to explain the role of the above additives in reducing solution mass transfer. Reaction between the Zirconium or Titanium Dissolved In Liquid Bismuth and an Iron or Steel Surface Reaction between Zirconium Dissolved in Bismuth and the Surface of Pure Iron-—A small pure iron crucible (analyzed by the supplier to contain 0.8 ppm N was contacted with bismuth containing approximately 0.1 pet Mg and varying amounts of a radioactive zirconium tracer. The crucible was then inverted at the temperature of contact. The thin residual layer of adherent bismuth was dissolved in cold, concentrated nitric acid. The crucible surface and the solidified bismuth were then analyzed for radioactive zirconium. An analysis of the activity loss on the crucible surface and the weight loss of the crucible during the nitric acid treatment showed that the acid treatment removed the zirconium that had originally been dissolved in the adherent bismuth, but not any zirconium that may have reacted with the crucible surface. The crucible was then pickled in warm aqua regia to remove all surface activity, hydrogen-fired at 600°C, and recontacted with a new liquid alloy. The results of the experiments contacted 1 hr at 450°C show, Fig. 1, a Langmuir-type adsorption with an adsorption free energy of approximately 17 keal per g atom Zr.5 This deposit was estimated to contain 1 atom of zirconium for each 7 to 8 iron atoms on the crucible surface, assuming a surface roughness factor of the pickled crucibles to be five. Increasing the temperature to 520°C caused consi-

Jan 1, 1959

By AIME AIME

MANY producers have held that the only workable quicksilver ore is easily recognized by its .cinnabar content. In most cases this is true. A noticeable exception is a. particular opalite deposit where part of the ore now being mined in considerable quantity shows only the yellow mineral, calomel, or its alteration products. This mineral, on exposure to the sunlight, quickly becomes coated with gray or black layers that may be removed by scraping to reveal the yellow mineral beneath. The blackening of this mercuric chloride on exposure to sunlight shows reaction to form metallic mercury, which is usually plainly present in this class of ore.

Jan 1, 1929

By P. Ramachandrarao, T. R. Anantharaman

CONSIDERABLE interest has lately been evinced as regards the nature of chill zones in solidified metals and alloys. Biloni and Chalmersl were the first to show through their study of segregation substructures in some nonferrous alloys that the formation of the dendritic region may be preceded by a diffusionless solidification process, viz., predendritic solidification. Subsequently Bower and Flemings2 tried a special solidification technique wherein the liquid was drawn into a narrow copper mold with polished surfaces and concluded that convection might trigger some multiplication mechanism leading to grain refinement. Using uncoated and partially coated surfaces for molds in the Bower-Flemings technique as well as in conventional molds, Biloni and Morando3 have very recently brought out the importance of the rate of heat extraction on the mechanism of solidification. We report here on the surface structures and substructures observed in a Sn-1 wt pct Pb alloy solidified at even higher cooling rates (riz., l05 to l07 ºc per sec) than those employed by earlier workers. The alloy was made by melting tin (99.99+ pct) and lead (99.9+ pct) in a silica tube under vacuum. Small quantities of the homogenized alloy (0.5 to 1.0 g) were then quenched (or splat-cooled) from the melt by the "gun technique" developed by Duwez et al.4 The thickness of the resultant foils varied from specimen to

Jan 1, 1970