Search Documents

By John W. Tieman

Coal is a term applied to vegetable matter which, through geological processes of heat and pressure, has had both its physical and chemical properties changed. Because its chemical composition is variable, geologists classify coal as a rock rather than a mineral. Peat represents the initial stages in the development of coal, although not classified as coal itself. PHYSICAL PROPERTIES OF COAL The physical properties are concerned with the characteristics of coal in its natural state, or prior to its end use as a fuel. For example, the hardness of coal determines the maintenance cost on coal handling equipment; the specific gravity of coal determines the coal preparation techniques used in a cleaning plant as well as the capacity of coal bins, boats and size of cargo, and other coal storage facilities. The physical properties are, of course, dependent upon the chemical constituents that make up coal, and thus all properties are interrelated. Specific Gravity The specific gravity of a body is the ratio of the weight of the body in air and the weight of an equal volume of water. The specific gravity of pure coal ranges between 1.25 and 1.70, generally increasing with rank. The most important use of this physical characteristic is the part that it plays in the cleaning of coal by wet wash methods. The basic principle on which these operate is that the specific gravity of coals differs from their associated impurities and that there is a relationship between the velocity of the fall of particles in water and their density. Since the specific gravity of slate is around 2.5 and pyrite is about 5.0, pyrite and slate will fall to the bottom of a container filled with water more rapidly than coal. If the water is given a pulsating motion by

Jan 1, 1973

By C. W. Chen

MARTENSITE transformations in ß Cu-Al alloys have been studied by Greninger1 and other investigators. According to Greninger, the parent phase ß1 an ordered body-centered-cubic structure obtained from ß phase by suppressing the eutectoid decomposition, transforms into an ordered hexagonal-close-packed phase in composition containing 12.9 to 14.7 pct Al. The M, temperature decreases with increasing aluminum content; for the alloy containing 14.5 pct Al, for example, the ß1??' transformation occurs below room temperature. More recently, Kurjumow2 studied the transformation in ß Cu-Al alloys with the addition of nickel. His report stimulated new interest in the subject due to the observation of completely reversible transformation without hysteresis in the transformation temperature ranging from 10° to —10°C. In the present paper some characteristics are described of the transformation of Cu-Al-Ni alloys that were partly studied by Kurjumow. Experimental Procedure High purity copper (99.999 pct) and aluminum (99.99 pct) and electrolytic nickel were used in the preparation, by the Bridgman technique, of single crystal specimens which contained aluminum and nickel of 14.5 and 0.5 to 3.0 pct, respectively. Polished surfaces were prepared mechanically. Specimens were then chemically etched to remove distorted material, homogenized at 1000°C for several hours, and quenched drastically to room temperature in a 10 pct NaOH bath to produce the parent phase ß1. The transformation was studied under a microscope and, in some cases, recorded by means of motion pictures. A device similar to that designed by Greninger and Mooradian3 was used to cool and reheat the specimens. Results and Discussion When the specimens were cooled below room temperature, the ß1 to ?' transformation began at 10°C with the appearance of ?' crystals In relief, Fig. la. As the specimen temperature dropped further, the transformation continued, either by the growth of the ?' crystals, with the ß1 — ?' interface moving into the ß1 phase, Fig. 1c and 1d, or by the formation of new ?' crystals, Fig. 1b. As a consequence of the former process, banded structure is observed as a common feature of the low temperature phase. According to the theory of the formation of martensite by Wechsler, Lieberman, and Read,' the bands of ?' phase are probably twin-related, as is the case in the diffusionless phase change of In-T1 alloys,5 but this was not revealed by X-ray tech- niques. New ?' crystals, in needle form, often emerged suddenly across the ?' bands during the transformation. These acicular crystals then grew, both in length and in width, see Fig. 2a through 2d. The transformation on cooling is completed at about -35°C. Upon heating, the reverse transformation started at —10° C, in a manner nearly opposite to the transformation on cooling, and completed at 35°C. There was no noticeable change in the transformation temperature when the nickel content was varied within the limits previously mentioned. Through control of the specimen temperature, the transformation can be started, stopped, or reversed at will. This phenomenon has frequently been observed in the martensite transformation of many nonferrous alloy systems. Other systems are Au-Cd6 and In-Tl.5 ow-- ever, in the latter systems, the transformation is accomplished by single interface motion if the specimen composition is homogeneous and the temperature gradient in the specimen is uniform and sharp, whereas in the Cu-Al-Ni specimens, only multiple interface transformation is observed. The speed of the interface motion appears to be a functionof the rate of temperature change and the temperature gradient across the specimen length. In one case, in which the temperature increased at the rate of 10°C per min and there was no temperature gradient along the specimen axis, the speed of the disappearance of a ?' plate was determined, by the study of the motion pictures made, to be 26 µ per sec. Quench markings were observed on the polished surfaces of specimens. The markings were grouped into one or more sets of different orientations, and were parallel in each set. The ?' plates formed in subsequent transformation were parallel to the markings, indicating that the ?' plates and the quench markings had the same geometric relation-ship to the ß1 matrix. The quench markings on two intersecting surfaces of a specimen were therefore used in the determination of the habit plane of transformation, by the trace method suggested by Barrett.' Results obtained from five sets of markings in three specimens indicate that the habit plane is an irrational plane about 2" from one of the {221} planes. This is very close to the habit plane (3" from 221 planes) of ß Cu-Al alloys containing more than 13.0 pct Al.1 The martensite transformation of Cu-Al-Ni alloys is reproducible. No sluggishness was found between consecutive transformation cycles, although a slight difference in the distribution pattern of the ?' plates was observed, compare Figs. Id and 2d. The transformation can be strain-induced. This characteristic has been tested by a simple method. When a specimen was elastically strained slowly in a vise, ?' plates were gradually produced in the same fashion as during transformation on cooling, This test was done at room temperature, and thus above the M,

Jan 1, 1958

By Jacob Reese

longer and tougher. In the worst case I have observed, viz., two inches difference in circumference, this difference in hardoess, as observed from the cutting, was more marked than in the other cases. Tires are always grouped in sets by the manufactrlrers fiorn their knowledge of the chenlical camposit,ion of the steel, with an attempt to get those in one set which have the same degree of hardness, so that the wear shall be equal all around ; they succeed pretty well on the average, but I have been noting the exceptioiis. Jacob Reese, PittsHukQh, Pa. : I have been very much interested in the reading and discusion of Dr. Dudley's paper. As far as it selates to the data of work performed by the rails, and the determination of their physical and chemical properties, I have nothing but commendation of Dr. Dildley to express, as the investigation covered a greater range, and was performed with more care in detail, than any similar work which has come under my notice. But I beg leave to differ with Dr. Dudley in his conclusions. What are the factors of hardness? Are they not carbon, silicon, phosphorus, and manganese? Now it is an untlisputed fact among iuetallurgiml experts that pure carbon and pure iron make the best steel of all degrees of carburieation, and for all purposes. While carbon hardens, it also strengthens the metal, but silicon, phosphorus, and manganese, in hardening, make the metal also brittle, and are injarious in any amount. Carbon should be called a strengthener; and I claim that a steel rail made hard with carbon, with the other three hardeners absent or reduced to a minimum, will carry a greater tonnage than any of Dr. Dudley's soft rails. But until the basic process is put into operation in this country we cannot expect to produce Bessemer or open-hearth steel without the presence of silicon, phosphorus, and manganese, in consitlerable quautities, aod I greatly donht the possibility of reducing the perceutage of any of them by the prment practice without seriously diminishing the output, and correspondingly increasing the net cost of production; which is an important question, since the increased life of the rail may be more than balanced by its increased cost. I think that the soft rails performed a greater amount of work, because they contained a less amorlllt of silicon, phosphorus, and wangatwe (britlkrcr, if I may so term them), and that carbon does wt reduce the wearing capacity of rails. I believe that a rail made by the baqic process, with silicon, phosphorus, and manganese reduced to a minimum, and containing 0.60 carbon, will be stronger

Jan 1, 1881

By R. B. Gordon, D. A. Koss

Ultrasonic-atlenuation changes due to the formation of free dislocations have been observed during tensile tests of magnesium and LiF single crystals and samples of polycrystalline Results on the LiF and samples are similar: A preyield attenzration increase is observed which, however, be-corlzes smaller as the magnitude of the drop in load al yielding increases. This indicates that the yield point observed in these materials is due to dislovation rather than dislocation unpinning and that the initial density ' free dislocations must be low if the yield point is to be sharp,. Tests on the magnesium ere conducted at both 27" and 200C. Magnesium has the unusual property that the yield drop is larger at the higher test temperature and is accomplished by a decrease in attenuation. The latter is due principally to the temprovary pinning of detained dislocations by highly solute atoms. After strain aging., a stress as low as 0.3 bur suffices to unpin dislocations; microstrain measuements of sufficient sensitivity should. reveal plastic flow at stress levels this low IN another paper,' we describe the technique of simultaneously observing ultrasonic-attenuation changes and plastic microstrain during deformation of spher-oidized carbon steels. Changes of ultrasonic attenuation indicate damping effects caused by the oscillation of long, freely moving dislocation segments. Simultaneous microstrain measurements are used to indicate total dislocation motion. The dislocation-damping observations are most useful in the study of the early stages of deformation where the dislocation density is low and the plastic strain is small and relatively difficult to measure. Particularly interesting results are found in materials which display sharp yield points. Observations of these phenomena are reported here for three materials: single-crystal LiF and magnesium, and poly crystalline molybdenum. EXPERIMENTS Dislocation-damping effects were observed by measuring changes in acoustic attenuation with the ultrasonic-pulse method. The end faces of each of the specimens were ground flat and parallel and a quartz 10 Mc per sec, x-cut transducer was attached to one face. The bonding agents used were: a) "Nonaq" stopcock grease with magnesium, b) beeswax with LiF, and c) salol with molybdenum. With the LiF, the best acoustic signals were obtained at 45 and 50 Mc per sec; all other measurements reported are at 10 MC per sec. The Sperry Ultrasonic Attenuation Comparator2 was used to measure attenuation changes. In the

Jan 1, 1967

By K. E. Brown, J. P. Brill, A. R. Hagedorn, T. C. Doerr

A recent correlation for multiphase vertical flow by Hagedorn and Brown1,7 has been used to examine the effect of numerous variables such as pipe size, gas-liquid ratio, liquid flow rate, liquid viscosity, liquid surface tension, oil API gravity, water cut, etc., on flowing pressure gradients. Most previous correlations were derived by using a form of the general energy equation which assumed negligible changes in kinetic energy. Under certain flow conditions this can lead to serious errors in predicting pressure traverses. Examples of traverses calculated both with and without the kinetic energy term are included here. The Chew and Connully correlation for calculating changes in viscosity with changing pressure and temperature has been extended so that the effect of a changing viscosity with depth on pressure gradients can also be predicted. Examples illustrating the effect of tubing size show the importance of this correlation in determining pipe sizes for initial well completions. Limitations on production rates in small pipe sizes from excessive friction losses can be predicted with greater accuracy. The combined use of a vertical-flow correlation with a horizontal-flow correlation provides a method for determining the maximum flow rate possible from both flowing and gas-lift wells. Examples are included to illustrate application of the combined use of vertical and horizontal-flow correlations in optimizing production rates and minimizing excessive costs from over injection of gas in gas-lift wells. INTRODUCTION The problems of multiphase vertical and horizontal flow are immediately encountered in any producing well. Fig. 1' shows three stages of production: flow in porous medium, vertical flow and horizontal flow. All three stages affect the production rate from a well. If we are confronted with a particular well and consider only the variables involved in the vertical and horizontal stages of Fig. 1, we should be capable of calculating the flowing bottom-hole pressure necessary to produce a particular flow rate. A change in any of the variables results in a new solution to the problem. Recent approaches in developing horizontal and vertical-flow correlations have improved to the extent that the solution can now be obtained with more confidence than previously. VERTICAL AND HORIZONTAL FLOW CORRELATIONS Since Poettmann and Carpenter's' original work in multiphase vertical flow, there have been many additional vertical-flow correlations developed which have greatly improved the accuracy of pressure-loss calculations. These

Jan 1, 1967

By Bauer. Larry G.

The vast coal reserves in the Wyoming, Montana, North and South Dakota region are sufficient to supply the total energy needs of the United States for several hundred years. Not only is there an abundance of this sub-bituminous and lignite coal available, but it is easily obtainable by strip-mining . The overburden varies from several feet to several hundred feet. This western coal has yet another asset, namely, a low sulfur content. Whereas eastern and midwestern coal has a sulfur content of 2.5%, the upper Great Plains coal contains sulfur in the 0.5% range. The importance of the sulfur content of the coal is a direct result of federal government emission standards for sulfur dioxide (SO2). Hand (1) points out that "sub-bituminous coals and lignites have a propensity for retaining this sulfur in the ash under certain conditions which is not evident in higher rank coals." This would tend to reduce further the SO2 concentration in the combustion gases of boilers. Western coal is no panacea, however, in that it is far removed from most population and industrial centers. Furthermore, the moisture content of the coal varies from 20 to 40%. This moisture is almost exclusively inherent, that is, it is chemically and physically bound to the organic matter of the coal. It is believed that the water forms a part of the coal structure perhaps as water of hydration of organic salts or organic acids, perhaps by hydrogen bonding, or perhaps by simple adsorption (2). The primary market for this coal is the electric power industry. Lesser markets will be as coke for the steel industry and possible as a raw material for coal gasification and coal liquefaction plants.

Jan 1, 1983

By Z. F. Oszter, D. Vincent, W. K. Behrands

With the expansion of open pit operations, belt conveyors are going to be used in the 13 608 to 18 144 t/h (15,000 to 20,000 stph) capacity range, which calls for a review of some of the horsepower calculation methods. This paper presents methods (based on German research data, field tests and theoretical considerations) for the evaluation of the Ky factor in the CEMA formula for belt conveyors of large carrying capacity, which fall beyond the limits of the data given in tables in the CEMA book. (The CEMA limits are 407 N\\m (300 lb ft) and Tave = 7.3 Mg (16,000 lb). At these large loads, the impression resistance of the belting on the idlers plays a major role, which in turn influences the magnitude of the drive horse power required. An example will illustrate the order of magnitude difference of the horsepower values obtained by using a conventional calculation method and the suggested method, as well as the beneficcia1 influence of the 4-roll idler in comparison to the standard 3-roll unit for a large caving capacity belt conveyor. This paper concerns itself with the analysis of the resistance to motion of belt conveyors, emphasizing the evaluation of the frictional resistance to motion due to load and belt pressure on the idlers and the flexing resistance of the belt and material when passing over the idlers. In the case of long and heavily loaded belt conveyors, the aforementioned resistances reach extremely high values calling for close analysis of the phenomena, presently not calculable with normally used formulas. This paper establishes correlation between experimental and empirical data presenting practical formulas a tool for the designer of high-capacity belt conveyors. The application of the formula is illustrated in an example in the Appendix.

Jan 1, 1981

By R. H. Ogburn

THE GROUND now being worked by the Fairbanks Exploration Co., near Fairbanks, Alaska, has been known to be gold bearing since 1901. In the early days it was worked by drift mining and other small-scale methods. In 1922, Hammond started prospecting the gold-bearing ground and obtaining options on the properties desired. Two years later the present Fairbanks Exploration Co. started taking up the options, and preparing to exploit the ground. For the prospect drilling Keystone drills were used, with holes at the points of equilateral triangles 600 ft. apart. Holes were also put down more closely spaced to determine the limits of dredging ground. In the first drilling casing was used to the bottom of the holes, but in later work the casing was put down only to the bottom of the thawed ground, and the rest of the hole put down without casing. The gold content was determined by panning, each 2 ft. of depth being determined separately. Where no casing was used the size of the hole was determined by using water to measure its volume. The greatest concentration of gold occurs at or near bedrock. All the gold-bearing streams head in one big dome. Gold, however, is not found clear to the head of the creeks, the pay being first found some distance downstream from the head.

Jan 1, 1933

By Lawrence Adler

MINE hoist ropes have hitherto been selected by successive approximation, a process both tedious and inexact. The proposed expression is a readily solved synthesis of existing data and the following standard equation:' [ W + Wr + (W + Wr) -a 9 (W + W)f + b] n=T [1] For convenience, a glossary of all terms appears on page 564. Since rope weight (W,) and bending load (B) are functions of unit rope weight (Wv), which in turn is a function of rope strength (T), W, and B can be expressed in terms of T. W, as a Function of T: A study of the curve in Fig. 1, unit rope weight vs strength, yields Eq. 2: W. = -f- [2] Therefore Wr = WvL = T. [3] iv B as a Function of T: From Fig. 2, unit rope weight vs diameter, Eq. 4 is obtained: W, = 1.6d2 [4] B is related2 to d and D, and d has been expressed in terms of W, by Eq. 4, so the curve B vs W, (Fig. 3) gives Eq. 5: 177,000 177,000 This may readily be checked from the expression3 for a 6x19 rope, i.e., d3 B = 288,000D Since d2 = 0.625 W, and N = substituting d into the above expression gives Ea. 6: 180,000 180,000 B T, which will be used. [6] Into Eq. 1 substitute Eq. 3 and Eq. 6, noting that f=0.02: W + T 1.02+=T. [7]

Jan 1, 1958

By G. Gutierrez, M. C. Fuerstenau, J. D. Miller

The response of pure goethite and two natural iron ores to flotation with potassium octyl hydroxamate is presented. The ores contained 12.5% and 39.7% iron; concentrates containing 69.5% and 61.5% iron, respectively, were obtained with additions of 0.4 lb/ton hydroxamate. Selective flotation of iron oxides from associated gangue minerals has proven difficult in the past with standard collectors, such as sulfonates and fatty acids. As a result, recent work has been directed toward silica flotation with calcium activation after the iron oxide surfaces have been blinded with certain starches.& The results obtained with this technique are encouraging. This method, however, involves depressing a mineral that would normally float under the conditions employed. A preferable method would involve floating the iron oxide because quartz is naturally depressed until activated. Earlier work involved this approach, but in view of the results obtained, collectors that exhibit greater specificity for iron are needed. During an investigation of chrysocolla flotation with potassium octyl hydroxamate, a metal chelate former, it was observed that pyrite floated well with low additions of collector.3 This phenomenon suggests that hydroxamate has a rather strong affinity for iron, and that other iron-bearing minerals should also respond to flotation with octyl hydroxamate. The object of this paper is to determine this response. The experimental work was divided into areas, the first of which involved microflotation experiments with pure goethite with an apparatus described previously.4 Goethite was selected because of the ease

Jan 1, 1968

By R. P. Smith, L. S. Darken

FOR a high-purity iron-carbon alloy, the phases existing at equilibrium at temperatures slightly above the temperature of the metastable eutectoid are austenite and cementite (hyper-eutectoid) or austenite and ferrite (hypo-eutectoid) and those below the eutectoid temperature (carbdn content > 0.02 pct) are ferrite and cementite. Such an alloy, held in a carefully controlled and measured temperature gradient (about 1 cm per deg) which includes the eutectoid temperature, then quenched and examined metallographicall.y, provides a precise measure of the eutectoid temperature. The samples were hollow cylinders approximately 1.3 cm OD, 0.63 cm ID, and 2.5 cm long, which had been carburized to the desired carbon content at 1000°C with an appropriate hydrogen-methane mixture. In order to cool the samples to room temperature with a minimum change of carbon content and absence of cracks they were quenched in a Cerro Bend bath at 480°C, followed by a water quench to room temperature. Three cylinders were suspended in the furnace1 in a purified helium atmosphere, by a closed end, thin wall, silica tube which also served as a thermocouple well. The top and bottom cylinders served only as a means of making the temperature gradient along the center cylinder more uniform. The temperature was determined with a platinum-platinrhodium thermel calibrated by comparison with a thermel certified (* 0.5OC) by the National Bureau of Standards. After holding in the temperature gradient for 24 to 72 hr the samples were quenched in Cerro Bend at 480°C, followed by

Jan 1, 1960

By Sidney Cornell

THE technical- advantages of adding oxygen to air and producer gas, or using it as a reactive agent, producing 400 B.t.u. gas instead of. the present 150 B.t.u., with higher flame temperatures and a reducing flame possible, with a smaller volume of gases passing through a furnace, will result in quicker melting, sharp working, and the production of a higher quality steel. Probably electric-furnace quality steel can be produced in an open-hearth furnace using oxygen. A modern, standard, 100-ton open-hearth furnace, with all equipment, costs from $350,000 to $500,000; there are about 1000 open-hearth furnaces in this country. When considering the use of oxygen in the open-hearth furnace, it is necessary to study: (1) The use of oxygen in the present furnaces, such that modification of existing furnaces and equipment cost the minimum, although the full advantages of oxygen are not thus obtainable. (2) The use of oxygen in a furnace designed for its use, producing quality and quantity steel at the lowest possible cost. This entails the junking of approximately one-half the value in existing equipment-writing off $250,000,000. The basis of such an estimate is the present cost of manufacturing open-hearth steel. Objection may be taken to some of the unit prices here given, but while some companies obtain their ores for much less, the prices quoted are -market price. They are used to show the maximum economy obtained by oxygen at that point.

Jan 11, 1924

By George H. Willis

In the second half of the 19th century, bimetallism progressively was replaced by gold standard. After World War I and the 1931-33 depression, gold was mainly reserved for official international transactions and internal use was restricted. Changes since 1971 have shrunk official international use of gold. International payments deficits and surpluses are now financed by Private and official credit, rarely by gold. This historical review covers evolution of: (1) internal and external private use, (2) internal official use, (3) external official use, (4) its role in the International Monetary Fund, and (5) use as unit of account. For this paper I have tried to take a longer perspective than is usually possible, and to look, even if very briefly, at the changing relationship of gold to the monetary system over the last 200 years or so. There are, I believe, some long-term trends, continuing down to the present day. These trends have seen gold replaced by some form of paper assets in one monetary function after another. These past trends may help us to understand where gold stands now, and possibly will throw some light on the future. Because it seems to me that gold in the past has performed various functions related closely or marginally to money, I have divided this rapid historical review into several sections: (1) the internal and external private use of gold, (2) the internal official use of gold, (3) the external official use of gold, (4) gold and the International Monetary Fund, and (5)gold as a unit of account.

Jan 1, 1980

By H. P. Leighly

WORNER1 briefly studied the embrittlement of titanium by mercury. He found that mercury will wet the titanium surface at 400°C in vacuo, if the specimen had been heated previously to 700°C to dissolve the oxide coating. Subsequent exposure to the atmosphere causes the mercury film to recede rapidly. Bending of the titanium specimen even after the mercury film has receded results in a brittle fracture. For the study of the embrittling effect of mercury on titanium, specimens 2 by 12 by 0.051 in. were cut from RC-130-A sheet, an alloy having a nominal 8 pct Mn content and a mixed a-ß structure. The specimens were stressed horizontally at a predetermined value after which a plastic ring having a cavity 1/2 in. diam by 1/2 in. deep was placed on the specimen. The cavity was filled with mercury and a hole was drilled in the specimen through the pool of mercury. If the stress level was high enough, fracture occurred instantaneously with the drilling. By repeating the test at different stress levels, the threshold stress can be determined. Mercury embrittlement causes a drastic reduction in the ultimate tensile strength of this alloy from 132,000 psi to about 15,700 psi. The drilling of the hole, in the absence of mercury, does not change the tensile properties. Fig. 1 shows the typical fractures observed as a result of the embrittlement of this alloy by mercury. The central portion of the fracture was brittle represented by the jagged region which appears to have occurred on the shear planes at about 45 deg to the stress axis. Ductile fracture, which is perpendicular to the stress axis, occurred near the specimen edges accompanied by a reduction of the specimen thickness. Examination of the fracture reveals that only in the brittle region does mercury wet the

Jan 1, 1962

By W. H. Bassett

IN the commercial annealing of cartridge brass there are four points regarding which definite data are essential. They have to do with the correct interpretation of grain count in its relation to annealing temperature and, incidentally, to Brinell hardness. These points are: 1. The comparison of the grain sizes of two cartridge-brass mixtures: 69 copper, 31 zinc, 0.376-in. (9.5-min.) gage; and 68 copper, 32 zinc, 0.130-in. (3.3-mm.) gage. 2. The comparison of the grain sizes of annealed metal that had previously been reduced by rolling varying amounts; for instance, 20.0, 36.6, 50.9, and 59.1 per cent. 3. The determination of standards for grain sizes on annealed brass of the composition 68 per cent. copper, 32 per cent. zinc and 69 copper, 31 zinc. 4. The comparison of grain size with Brinell hardness on identical samples of annealed metal. In their comprehensive and thorough investigation of the recrystallization of cold-worked alpha brass on annealing,1 Mathewson and Phillips have discussed the relations between temperature of anneal, degree of deformation, and structural alteration in alpha brass. They have also shown certain comparisons between the ordinary physical properties and the grain size of annealed brass. The purpose of the present investigation is mainly concerned with the grain size of cartridge brass, its relation to Brinell hardness, and the publication of sufficient data to enable those engaged in the inspection of such material to have a correct foundation upon which to work.

Jan 1, 1919

By Maurice Rey, H. Beavers

THROUGH circumstances connected with the war, the senior author lost his records, therefore it has been impossible to include numerical data in this paper. The arsenical quicksilver ore investigated had been roasted, with poor metallurgical results. The vapor-tension temperature curves of mercury and arsenious trioxide are similar, and the arsenical compound hampers the coalescence of mercury drops in the condenser and is the cause of large stack losses. The ore was a gray limestone carrying small amounts of carbon and mineralized with cinnabar and two arsenic minerals, realgar (As2S2) and arsenopyrite (FeAsS). The proportion of realgar often exceeded that of cinnabar; the proportion of arsenopyrite was smaller. The grade of the ore varied between 0.8 and 4 per cent Hg. The problem was to make a high-grade mercury concentrate, as free from arsenic as possible. The water used throughout the testing was hard, having a pH of about 8. FLOTATION OF REALGAR Realgar showed a very strong tendency to float. It formed a film at the surface of the pulp and floated in abundance with only pine oil. Therefore an attempt was made to float the realgar before the cinnabar, but this was not very successful; the percentage of mercury in the realgar concentrate could never be brought below 2 or 3 per cent. Cinnabar slimed easily and floated with pine oil, so that some of it always accompanied the realgar. There was also the question of the cinnabar-arsenopyrite separation. On further investigation it was found that realgar can be floated not only with pine oil but even better with a combination of hydrocarbons and pine oil. Washing the ore with ether revealed that it contained hydrocarbons, which helped to float the realgar. In this connection it belongs to the same class as carbon, sulphur and talc. It can be floated also with a xanthate, when activated by a heavy-metal salt. The conditions favoring the two types of flotation are opposed, as activation by a copper salt facilitates xanthate flotation (in fact, is even necessary to it), whereas it hinders pine oil and petroleum flotation. One type of flotation can be termed nonpolar and the other polar, a distinction that has been stressed in a previous paper.1 DEPRESSION OF REALGAR AND FLOTATION OF CINNABAR 'Many chemicals were tested in an attempt to float the cinnabar and depress the realgar. Finally starch rendered soluble with caustic soda was tried, also several grades of commercial soluble starch, and dextrin was found to be the best and the most convenient reagent. Several of these starch preparations have a strong flocculating effect on the pulp, which is a distinct disadvantage. Dextrin, with its low flocculating power, is excellent. It is noteworthy that starch preparations are also depressants for carbon and talc, so that the fact apparently has a general

Jan 1, 1941

By Marsh S. Watson, Robert A. Howard

An electrolytic model study has been made of the relative productivity of perforated casing. The results show that the relative productivity is roughly one-half to two-thirds of that predicted from point-sink calculations. This discrepancy can he satisfactorily explained on the basis of casing interference. The relative productivity was found to he insensitive to spatial arrangement of the perforations. INTRODUCTION The relative productivity of wells with perforated casing has been treated mathematically by Muskat.' In his treatment the perforations are represented by small spheres, thus enabling him to approximate the flow by that to point sinks. By neglecting interference between the flow into the various spheres representing the perforations, one may deduce the approximate formula Qu 1/rp - 1/rw • (1) I + b/2n _________ 2n In re/rw Where Q is the flow rate into spherical sinks located in the median plane of the sand laver Qo is the open hole flow rate (uncased hole of radius rw) b is the thickness of sand layer under consideration (always one foot in this paper) n is the number of spherical sinks in the sand layer rp is the radius of a spherical sink rw is the well radius re is the drainage radius of the well. Fig. 1 is a comparison of values calculated from equation (1) with Mus-kat's values. It will be observed that the approximate values are in error by less than 21/2 per cent. The disturbing effect of the casing on the flow line; is not explicitly taken into account by Muskat, but he reasons that interference between the flow pat- terns from the various point sinks will result in a negligible flow in the region within the well radius, and that no appreciable error will result from not explicitly excluding flow from this region. This line of reasoning is open to question, however, as the flow impedance, in the immediate vicinity of the well, of a hemispherical cavity in contact with an opening in the casing is twice that of a spherical sink in a continuous sand layer. There will be a difference, moveover, between the flow into a hemispherical cavity and that into a circular hole in the casing. .This latter difference can best be appreciated by comparing the flow from a semi-infinite medium into a hemispherical cavity at the edge of the medium with the flow out of a circular opening of the same radius as the hemisphere and which is also on the edge of the medium. In this case2 ------= —2, showing that the difference in flow rates into differently shaped cavities is quite appreciable. It was the purpose of the investigation reported here to determine to what extent flow into circular perforations in casing departs from the values calculated by Muskat. For this purpose an electrolytic model was used.

Jan 1, 1950

By Maurice Rey, H. Brevers

THROUGH circumstances connected with the war, the senior author lost his records therefore it has been impossible to include numerical data in this paper. The arsenical quicksilver ore investigated had been roasted, with poor metallurgical results. The vapor-tension temperature curves of mercury and arsenious trioxide are similar, and the arsenical compound hampers the coalescence of mercury drops in the condenser and is the cause of large stack losses. The ore was a gray limestone carrying small amounts of carbon and mineralized with cinnabar and two arsenic minerals, realgar (As2S2) and arsenopyrite (FeAsS). The proportion of realgar often exceeded that of cinnabar; the proportion of arsenopyrite was smaller. The grade of the ore varied between 0.8 and 4 per cent Hg. The problem was to make a high-grade mercury concentrate, as free from arsenic as possible. The water used throughout the testing was hard, having a pH- of about 8. FLOTATION OF REALGAR Realgar showed a very strong tendency to float. It formed a film at the surface of the pulp and floated in abundance with only pine oil. Therefore an attempt was made to float the realgar before the cinnabar, but this was not very successful; the percentage of mercury in the realgar concentrate could never be brought below 2 or 3 per cent. Cinnabar slimed easily and floated with pine oil, so that some of it always accompanied the realgar. There was also the question of the cinnabar-arsenopyrite separation. On further investigation it was found that realgar can be floated not only with pine oil but even better with a combination of hydrocarbons and pine oil. Washing the ore with ether revealed that it contained hydrocarbons, which helped to float the realgar. In this connection it belongs to the same class as carbon, sulphur and talc. It can be floated also with a xanthate, when activated by a heavy-metal salt. The conditions favoring the two types of flotation are opposed, as activation by a copper salt facilitates xanthate flotation (in fact, is even necessary to it), whereas it hinders pine oil and petroleum flotation. One type of flotation can be termed nonpolar and the other polar, a distinction that has been stressed in a previous paper. DEPRESSION OF REALGAR AND FLOTATION OF CINNABAR Many chemicals were tested in an attempt to float the cinnabar and depress the realgar. Finally starch rendered soluble with caustic soda was tried, also several grades of commercial soluble starch, and dextrin was found to be the best and the most convenient reagent. Several of these starch preparations have a strong flocculating effect on the pulp, which is a distinct disadvantage. Dextrin, with its low flocculating power, is excellent. It is noteworthy that starch preparations are also depressants for carbon and talc, so that the fact apparently has a general

Jan 1, 1941

By A. E. Chute

The shortage of sulfur is not only continuing but appears to be worsening, attended by steadily rising prices. At the same time emphasis on air-pollution abatement is also increasing. These two factors, a rising market and the growth of environmental attention, have encouraged producers to carefully review all possible sulfur sources. As a result, production of sulfur from hydrogen sulfide occurring in petroleum is receiving greater attention than ever before. Until about a decade ago, the practice of recovering sulfur from hydrogen sulfide separated from gases (either found naturally or generated in desulfurization of liquid petroleum) was wide1y recognized but contributed little to total free-world sulfur production. However, during the past ten years, the production of sulfur from this source has increased so rapidly that it now accounts for a substantial portion of total production. This trend shows no signs of slackening, and current forecasts predict that recovered sulfur may become the dominant source of supply within ten years, exceeding mined sulfur production. This paper is intended to list sulfur sources and relationships, and to discuss the potential of producing sulfur from petroleum. The processing involved, in addition to product storage and transportation will also be discussed along with important economic aspects of sulfur recovered from hydrogen sulfide. For many years, most of the world's elemental sulfur has been produced from salt domes, predominantly by the Frasch process. During the past decade, however, another production source has developed so quickly that it is expected to surpass the Frasch production sources within a short time. This new source lies in the petroleum gases and liquids from which dramatically increasing quantities of elemental sulfur are being recovered. In the phraseology of the trade, the sulfur so obtained is know as "recovered sulfur," a term which does not, as one might expect, include sulfur recovered from other sources such as smelter gases. The growth rate of recovered sulfur compared to that of Frasch sulfur, total elemental sulfur, and total Free World sulfur in all forms is shown in Fig. 1 Since 1963, sulfur consumption has exceeded production,with the natural result that the price of sulfurhas continually increased. The posted price reported for f.o.b. Port Sulphur, La., has risen from as low as $18 per ton in 1962 to $32.50 per ton in mid-1967. With freight and other charges, delivered prices have of course run much higher, amounting to $45 or $46 per ton on the east and west coasts. In some cases, spot sales for as much as $60 have been reported. Although it is playing an ever-increasing role in the sulfur market, recovered sulfur was originally a by-product of the removal of hydrogen sulfide from natural and petroleum refinery gases. Today, however, it is often the most valuable product of a multi-product processing facility. Since there are two major sources of recovered sulfur—production and refining processes —natural gas is included with liquid petroleum for purposes of this discussion. Sulfur from these sources is produced in the form of gaseous hydrogen sulfide which is removed from a gas stream and converted to elemental sulfur. Gases in which hydrogen sulfide occurs naturally are natural gas and the gas produced from a high=pres-sure crude=oil or condensate field.

Jan 1, 1969

By H.A. Bedworth

AlloTs of copper and silicon have been known for one hundred years or more but the commercial development of this type of alloy has taken place during the past few years. In 1905, Sperry l proposed the use of copper-silicon alloys for springs and other purposes for which copper-tin bronzes were used. Some attention was given to this proposal at the time but no one succeeded in producing a practical alloy containing more than a fraction of a per cent. of silicon. The equilibrium relations of the copper-silicon system were studied first by Rudolfi2 and later by Sanfourche 3 and Corson. 4 The constitution of the system has also been recently investigated by Matuyama, 5 and in the laboratories of the American Brass Co. by Smith. 6 Some of the physical properties of the copper-silicon alloys have been investigated by Norbury7 and by Geiss and Van Liempt.8 Summarizing the results of various investigators of the constitution of copper-silicon alloys, the solubility reaches its maximium value, 6.7 per cent. silicon, between 721" and '782" C. At 852" (1. the solubility is 5.25 per cent., while at 400" C. it is only 4.1 per cent. silicon. The copper-silicon alloy begins to get so hard at about 3 per cent, silicon that it is difficult to manage. It was found by Jacobs that the addition of manganese to this alloy considerably improved the working

Jan 1, 1929