Search Documents

By C. M. Young

THE safety lamp is the most common and convenient apparatus for detecting inflammable gases in mines, the presence of gas being shown by a blue flame, called the cap, if the wick has been lowered to suppress the luminous flame. The height of the cap increases with the proportion of gas and with the temperature of the lamp flame. Lamps of the Wolf type, the fuel of which is benzine, have a hotter flame than lamps in which vegetable oils are used, such as the Davy, and the Clanny, and are more sensitive than the latter and their many modifications. The Piehler alcohol lamp gives a still higher cap while the Clowes hydrogen lamp is most sensitive of all. While the effect of the temperature of the source of ignition is well known, the writer knows of no previous attempt to correlate the change of this temperature with change of the height of the cap produced. In order to determine the height of the cap at various temperatures, it was necessary to have a source of ignition the temperature of which could he accurately controlled over a considerable range. This condition was met by a coil of wire of high fusing point heated by an electric current controlled by a variable resistance. The use of a coil offered the further advantage of freedom from complications due to the flame of a burning fuel. Such a flame, being itself of variable height, would to some extent raise or lower the elevation of the base of the cap and therefore add to the difficulty of determining the height of the cap. Besides this, the presence of a small cap from the lamp fuel, commonly known as the "fuel cap, " would interfere with the observation of small gas caps. After some experiment, a coil was made of platinum wire, No. 26, diameter 0.016 in. The coil was 17/64 in. (6.746 mm.) in outside diameter and had eight full turns in a length of ½ in. (12.69 mm.). This was connected to an electric circuit through an adjustable resistance, as shown in

Jan 8, 1919

By Enrique Touceda

As IN the case of steel and the non-ferrous alloys in general, the use of the microscope in connection with the manufacture of malleable cast iron has proved of inestimable value to the industry. Had its use not been invoked, many facts either would not be known at all or, if suspected, would be confined to the realms of conjecture. No fairer statement could be made than that the start of real progress in the industry was coincident with the application of metallography to the product, though the full significance of this statement can hardly be appreciated except by those who not only are conversant with conditions as they existed at the time referred to, but are familiar with the character of works' practice at the present time. A few years ago, about the only test made to ascertain the physical properties of the product, t except in the case of certain plants, was the bending of a casting to destruction, not only with the object of discovering whether or not the metal was ductile, but for the purpose of inspecting the fracture. The characteristics of the fracture, if correctly interpreted, were known to be of value in locating the trouble in, castings that were inferior. In general, it was found that if a casting of medium or heavy section would bend through a wide angle before failure took place, the fracture in the majority of cases would have a black velvety appearance; while if it was held at different angles to the direction of the rays of light, it would show a change of color and an iridescent sheen. But an inferior air-furnace heat or anneal might yield castings which, if thin and consequently largely decarburized, could be bent double on themselves and still not possess the fracture described. If, on the other hand, a casting broke short, its fracture might have one of a great many different color and structural peculiarities. Depending on the cause of the trouble, such castings might have any of the fracture characteristics, of which the following is but a partial list.

Jan 2, 1920

By R. G. Fleck, W. R. Webb

Iron ore mining in the Adirondack region of northern New York dates back to the Revolutionary War. It is recorded that Benedict Arnold in his campaigns in the Lake Champlain area during the American Revolution utilized the local ores to produce armament and cannon balls. Through the efforts of early pioneers, the iron mining industry in northern New York gained impetus so that in the 1880's mines in the area accounted for nearly one fourth of the iron ore produced in the United States. Both magnetite and red hematite ores were mined during this period. With the discovery of the Lake Superior ores, the iron ore industry in New York started to decline and remained relatively unimportant until 1938. Modern day methods of mining and beneficiating sufficiently high tonnages of low-grade ores to justify the large expenditures for plant and equipment prompted a resurgence in northern New York mining. During the past several years, the production of iron ore from the Adirondack magnetites has greatly increased, and production which amounted to .6%, of the United States total during the 1918-1928 period (Mining and Metallurgy, November 1943) has been increased to 2.85% of the total in 1948. Today, Republic Steel is mining in the Port Henry-Mineville and Lyon Mountain areas; the

Jan 4, 1950

By P. G. Shewmon

Radioactive MgZA has been used to study the rate of self-diffusion in oriented single crystals of magnesium in the temperature range 468O to 635OC. The diffusion coefficients parallel and perpendicular to the c-axis are: Dl, = 1.0 exp (—32,200IRT) cm2 per sec and Dl = 1.5 exp (—32,500IR T) cm Qer sec. The ratio Dl/Dll was found to vary from 1.13 at 468 to 1.24 at 575 C. Assuming a vacancy mechanism, an explanation of this aniso-tropy of diffusion follows from a consideration of the difference in the saddle points for diffusion in and out of the basal plane. RECENT discovery of radioactive Mg2"'-' has made possible the study of self-diffusion in magnesium. The experimental procedure and the results of a study of diffusion in polycrystalline magnesium have been described in an earlier paper.V he present work is an application of the same techniques to the study of self-diffusion in oriented single crystals of magnesium. In the general diffusion problem the diffusion coefficient is a second order tensor relating the two vectors, the diffusion flux, and the concentration gradient. In a hexagonal lattice, such as magnesium, the complete determination of the diffusion coefficient D as a function of direction in the lattice requires a knowledge of D,, and D,, i.e., the diffusion coefficients parallel and perpendicular to the c-axis, respectively. It can be proven quite generally that in a hexagonal lattice D is independent of direction in the basal plane, and that out of the basal plane it varies with 0, the angle between the c-axis and the direction of diffusion, according to the equation D(B) = D,,cos2B + D,sin2B. [I] The proof of Eq. 1 depends only upon the symmetry elements of the hexagonal lattice and upon the transformation properties of a second order tensor." Therefore, Eq. 1 holds for any mechanism of diffusion and any c/a ratio. Experimental Procedure The experimental procedure used with polycrystalline specimens can be briefly outlined as follows. Radioactive Mg" was produced by bombarding a NaCl crystal with 350 mev protons and was chemically separated from the target as MgO. The Mg" was then vapor deposited on a specially cleaned magnesium specimen by heating the MgO on a tantalum ribbon in a vacuum. During the diffusion treatment, oxidation and vapor loss of the radioactive material were minimized by annealing the samples in pairs with the active faces in contact, each pair being inside a magnesium container, which was in turn surrounded by an argon atmosphere in a sealed Pyrex tube. The distance-activity profiles were obtained by measuring the activity of thin sections cut parallel to the original interface with a lathe. The only technique which was peculiar to this work was the preparation and orientation of the single crystal specimens. The single crystals used in this work were grown by E. C. Burke of the Dow Chemical Co., using a modified Bridgman method, in which the furnace and specimen were stationary while the temperature gradient moved.' In growing these crystals the starting material was distilled magnesium, the crucibles were machined from Acheson electrode graphite, and the furnace atmosphere was tank argon. The crystals were grown from sublimed magnesium with the following analysis: 0.0002 pct Al, 0.0017 pct Fe, 0.0009 pct Mn, 0.0001 pct Ni, 0.0006 pct Pb, and less than 0.01 pct Ca, 0.0001 pct Cu, 0.001 pct Si, 0.001 pct Sn, and 0.02 pct Zn. The two crystals used were roughly lh in. diam and eight in. long. The c-axis made angles of about 7" and 78", respectively, with the specimen axes. If the values of D obtained by the use of these two crystals are taken equal to D,, and D,, respectively, the error introduced by this assumption is less than 1 pct. This can be shown by combining Eq. 1, the identity sin% + cos'8 = 1, and the experimental fact that DJDn in magnesium was always less than 1.25.

Jan 1, 1957

By S. W. Miller

DURING the examination of welds made in steel by the oxy-acetylene and electric-arc processes, the writer has met with some unusual structures, which he has not encountered elsewhere. They seem to be quite closely associated with the welding methods used, and characteristic of them, and would seem to be worth noting, especially as the references to them in the literature are few, and their explanation not clear or complete. An introductory word or two about fusion welding may not he out of place. The oxy-acetylene process is based on the great and very local heat generated by the burning of acetylene in the presence of commercially pure oxygen, the two gases being thoroughly mixed before combustion. The theoretical temperature is somewhat under 4000° C., but on account of various losses, the actual maximum temperature is probably about 3000° C. 1 The electric-arc process, using a metal electrode, which is also the filling rod, generates a still higher and more local temperature. The actual temperature of the positive crater of the carbon arc is given as 3500° C.2 No figures have been found for the temperature of the arc using a metal electrode, but it would probably not be very different from that of the carbon arc, and probably higher than that of the oxy-acetylene flame. The greater localization of the electric arc is due to the fact that it is not surrounded by a large envelope flame as well as to its higher temperature; while the oxy-acetylene white cone, or welding flame, in which the carbon of the acetylene is burned to CO, is surrounded and preceded by -a long envelope flame, itself of quite high temperature, in which the CO is burned to C02, and the hydrogen of the acetylene to

Jan 2, 1918

By M. J. Marcinkowski, A. S. Sastri

A detailed compressive stress-strain analysis and transmission electron microscopy investigation has been made of the deformation behavior occurring in a 50 at. pct Ni-Ti (hypoeutectoid) alloy and a 54.5 at. pct Ni-Ti (hypereutectoid) alloy. In the case of the hypoeutectoid alloy, three stages of work hardening are observed. Stage I occurs at a very low stress and is associated with plastic deformation via martensite formation. Stage 11 is characterized by very rapid work hardening and is due to difficulties in causing further deformation in the fine martensite aggregate produced in Stage I. Stage III which occurs at very high stress levels is characterized by smaller work hardening rates and is due to the plastic deformation arising from alternate reconversions of the original martensites to martensites of varying orientation. Rapid quenching of the hypereutectoid alloy leads to very high yield strengths and is related to a fine precipitate dispersion that such treatment brings about. The present investigation represents the final phase of a three-part study directed toward an understanding of the solid-state transformations in near equi-atomic Ni-Ti alloys as well as the deformation mechanisms associated with these alloys. In the first part,"2 to be henceforth referred to as I, it was found that alternate simple shears on {112} planes and in (111) directions convert the parent B2 structure in the equiatomic NiTi alloy into two distinct close-packed monoclinic martensites. All of the marten-sites were of this type, whether they were formed by cooling or by plastic deformation, whether induced to form in bulk samples or in thin foils, or whether examined in the electron microscope at room temperature or below. On the other hand, in the second part of this investigation,3 to be reffered to as 11, it was shown that upon slow cooling to about 640°C. alloys in the neighborhood of NiTi which possess the B2 structure transform eutectoidally into their equilibrium phases Ti2Ni and TiNi3. However, preceding the formation of these equilibrium phases a series of metastable intermediate phases are formed. This paper will set as its goal the elucidation of the remarkable deformation behavior exhibited by NiTi. In particular, Buehler and Wiley4 have found equiatomic NiTi to be surprisingly soft, while Buehler et al.5 have shown this alloy to possess a memory effect: i.e., upon bending at room temperature it will revert to its original shape when heated to above about 50°C. In I it was shown that NiTi was soft in the sense that the yield stress was low; nevertheless, the alloy work-hardened at an extremely rapid rate to very high stress levels. On the other hand, the hypereutectoid alloys with somewhat higher nickel, say 54.5 at. pct (60 wt pct) have enormously increased yield strengths compared to those of the equiatomic alloys. In order to determine the atomistic processes giving rise to the above behavior, it was decided to examine samples that were wafered from bulk specimens deformed in compression to various strains using the techniques of transmission electron microscopy. EXPERIMENTAL TECHNIQUE All of the alloys used in the present investigation contained either 50 at. pct Ni (55.06 wt pct) or 54.5 at. pct Ni (60 wt pct) and were arc-melted in the form of a finger using the same techniques described in I and II. The finger was capsulated in a stainless-steel jacket and swaged at 850°C into rods. Compression specimens 0.300 in, long and 0.200 in. in diam were machined from these rods. In order to completely re-crystallize the samples and remove residual stresses, all of them were capsulated in evacuated quartz, annealed for 1/2 at 1050°C. and then furnace-cooled. Compression tests were carried out in an Instron tensile testing machine covering a range of temperatures from —196° to 200°C using procedures described previously.6'7 In all cases crosshead speed was 0.02 in. per min. Wafers 0.015 in. thick were spark-cut from the cylindrical samples at 45 deg to the compression axes after they had been deformed to the desired strain. These specimens were then spark-planed to about 0.005 in. and then electrochemically thinned for examination by transmission electron microscopy as described in I.

Jan 1, 1969

By H. J. Stehli

Probably the earliest sinter from lead ore was made in the product sinter boxes attached to some hand reverberatory roasters. The ore was drawn from the roaster bed when dead roasted, and then by laborious effort fritted together by rabbling at a high temperature in the sinter box. This was not a true sinter, but was a great improvement over the dusty dead-roasted fine ores. The Huntington-Heberlein pots were the first real advance in the art, and produced some real sinter. They required that the sulphides be preroasted to 5 or 6 per cent sulphur, and the long cycle of operating and deep bed of material used in the pots fostered the formation of densely fused material and fines. This necessitated crushing of the densely fused cake and returning to the next charge large amounts of fines screened out. The Huntington-Heberlein pots made comparatively high lead losses because the deep bed and high internal temperature together favored the volatilization of lead. Lime (CaO) was added to the charges, and this addition constituted the patented feature of the Huntington-Heberlein process. Its sole function we now know was to act as an isolator of the sulphide particles, and any other substance—for instance, iron oxide—of equal fineness performed the same function. The Savelsberg process used limestone instead of burned lime, and in this there was a definite advantage. The converting of CaCO3, to CaO is a highly endothermic reaction, so the lime acted not only as an isolator of sulphide particles but absorbed excess heat and to some extent prevented premature fusion of the sulphides. The Carmichael-Bradford process used gypsum instead of limestone, and had the disadvantage of adding more sulphur to a charge from which it was desired to eliminate sulphur. Here again the gypsum served only as an infusible isolator of sulphide particles. The first Dwight-Lloyd apparatus to sinter lead ores commercially was installed at Perth Amboy in 1907. The fact that lime in any form was necessary to sintering was quickly disproved by making excellent sinter from Bunker Hill and Sullivan table concentrates, silica sand and iron oxide only.

Jan 1, 1937

By Fredrick Laist, J. P. Cooper

In the spring of 1931 an experiment was made at Anaconda with a small reverberatory furnace, with which was combined a roasting shaft. The arrangement is shown in the accompanying drawing (Fig. 1) and requires but little explanation. The general idea was to roast flotation concentrates, mixed with the proper fluxing materials, by dropping them down a heated shaft, from which the calcines would enter the smelting zone of the reverberatory furnace through an opening in the roof. The hearth of the reverberatory was 3 ft. wide by 21 ft. long. The roasting shaft was 3 ft. square inside and had an effective height of about 20 ft. The reverberatory furnace was arranged so that it could be charged either directly through the roof with regular hot calcines, in the usual manner, or by means of the shaft, at the top of which were a feeding arrangement by which cold flotation concentrates, suitably fluxed, could be fed continuously and a pipe through which cold air was blown in. Means were provided for distributing the feed over the cross-section of the roasting shaft. At first a mechanical arrangement was used but later it was found that a simple cone served the purpose equally well and gave less operating trouble. On account of the small size of the equipment, it was realized that absolute capacity and fuel consumption figures would mean but little. It was not to be expected that ratios comparable to those obtained in large furnaces could be gotten, and the only way in which any idea could be obtained as to the possibilities of the combination furnace was to run it in parallel with the reverberatory furnace charged in the usual manner and operating without the shaft. The results of such parallel runs are given in Table 1. The amount of oil burned in the reverberatory was purposely maintained at substantially the same rate during both runs in order that the benefits resulting from the shaft might be gaged. It was expected that the shaft would considerably increase the capacity of the reverberatory and that a better fuel ratio would be obtained on account of the high temperature at which the calcines would enter the

Jan 1, 1934

By Frederick W. Bacorn

The paper of Reno H. Sales on Ore Deposits at Butte, Mont.,' is a careful and painstaking work, an important contribution to the literature of the subject. As is almost inevitable in a work of such magnitude, a few misstatements occur; and some of these I shall endeavor to point out. Mr. Sales has also fallen into error, as I think, in the application of his theory of ore deposition; and while the modification which I venture to suggest is a minor one geologically, it is of great economic importance. I refer to Mr. Sales's idea of an outward migration of mineralizing solutions from a supposed central copper zone. In order that I may make myself plain, I must first epitomize the theory as a whole, which I understand to be this: All of the Butte ore deposits (save those along the Continental fault, not herein considered) are derived from solutions of magmatic origin, which, at the beginning of their ascent from a great depth, were acid in reaction, hot, and were carriers of copper, zinc, manganese and other metals. As they departed from their point of origin they lost heat, and, because of reactions with the wall rock, became more and more alkaline. The metal deposited from these solutions in their hot condition was principally copper; and, as they cooled, they deposited less and less copper and more and more manganese and zinc, until the copper practically disappeared. With this theory in general I have no fault to find, nor have I, it must be stated, the qualifications necessary to enable me to pass upon it critically; but it seems to me to be reasonable and probable, and is one which I am quite willing to accept. But Mr. Sales, for what seem to me to be insufficient reasons, has assumed that there is one deep central source of copper, relatively rich and small, from which all the solutions emanated. From this central source the solutions rose, through one channel or through a group of channels, to the surface, at and within a small area called the central copper zone,

Jan 1, 1915

By Clarence W. Balke

SMALL buttons of fused tantalum have been produced by arc fusion in a vacuum, by drawing an arc between sticks of pressed tantalum and a tantalum-faced water-cooled copper block. However, ingots of appreciable size can be produced only by the heat-treatment of bars pressed from powder. The following outline covering the production of finished bars of tantalum by the methods of powder metallurgy is also used for the production of columbium, taking into account the difference in the melting points of these two metals. PRESSING THE POWDER With possibly a few exceptions, a pressing operation is one of the essential steps in the practice of powder metallurgy. In fact, the author's experience with a number of high-melting-point metals and with numerous types of hard carbide compositions has led him to believe that this operation is often one of the most important in the entire process, and frequently one of the most difficult to carry out in a satisfactory manner. Defects due to improper pressing can readily lead to a defective finished product. It is the author's opinion that rarely is a bar or other article pressed from metal powder in such a way that all parts of the piece are uniformly pressed. The nearest approach to uniformity of pressing is possibly attained when the powder is contained in a flexible receptacle, such as rubber, and is pressed under a liquid by hydrostatic pressure. However, this method is not generally applicable. Hydraulic pressing in steel dies where one or two punches are forced into the die must usually be resorted to. As the pressure in such a die is built up, the powder begins to cling to the walls of the die with a tenacity dependent upon the nature of the powder, and this results in a bridging action, so that the layers of powder adjacent to the moving punch are pressed more heavily than those further removed in the mass. Frequently, as the pressure is carried higher, there may be a mass slippage of the powder upon itself, with the result that slip cracks are formed within the pressed

Jan 1, 1938

FREderick H. Davis, Electrical Engineer of the Westinghouse Electric and Manufacturing Co., in charge of the plant at Bodie, Cal. (communication to the Secretary): I beg to offer, to complete the information conveyed in Mr. Leggett's paper, the following report of tests of the electrical efficiency of the power-transmission he has described:

Jan 1, 1895

By Job Goostray

IN THIS paper, as in so many other discussions of historical nature, there is little chance for original material and much has had to be rewritten from older papers, documents, accounts, reports, and the like, some of which are of doubtful authorship or contain conflicting statistics. Fully aware of these little historical pitfalls, the authors have tried to quote the origin where possible, and also to seek further confirmation when the statement warranted it, but cannot assume responsibility for certain facts and dates. The Encyclopedia Britannica was frequently consulted. The authors wish to acknowledge assistance from MacKintosh-Hemphill Co.-formerly the Fort Pitt Works-and also from officials of the Watertown Arsenal who loaned valuable books and gave much necessary information. They are particularly indebted to Colonel Dixon of that institution. The data on modern guns were furnished by Mr. F. Brauer of the Watertown Arsenal; Mr. H. S. Chaffee assisted by obtaining records and data of work carried on by the Builders' Iron Foundry of Providence, R. I.

Jan 3, 1925

By C. W. Hill

FLUXES, in general, may be classified according to their use as soldering, foundry or casting, and metallurgical and the chemistry of their action follows quite closely this division. The term foundry or casting fluxes, as used here, refers to the substances added to molten metals, preparatory to casting into molds or ingots, with the object of removing small amounts of impurities that have been introduced in handling or melting the metal, which was placed in a fair state of purity by the previous refining or metallurgical processes. The sources of these impurities are the oxide coating on the surface of the ingots, material extracted or mechanically removed from the crucible or furnace wall, and those formed by the reaction of the molten metal with the heating gases or furnace atmosphere. As commonly used, the term fluxes is applied to such materials as ammonium chloride, zinc chloride, salt, borax, and boric oxide. A second class of materials, usually called deoxidizers, includes substances, such as metallic phosphides, sub-oxides, carbides, and bo-rides, that reduce the metallic oxides present in the metal. A third class includes various compounds that are molten and non-volatile at the temperature of the molten metal and are used primarily to protect the surface of the metal from the action of the furnace or exterior atmosphere; to this class belong such mixtures as lime and fluorspar, lime and soda ash, various minerals, etc. In some cases these protective layers may act in a manner similar to the metallurgical fluxes and dissolve or unite with the oxide impurities of the metal, but as generally employed this latter action is negligible since there is little opportunity for the coverings to come into contact with more than the surface of the metal, and hence they are without action on the body of the molten mass. The use of fluxes is the result of factory experience and tradition, but an extensive study has not been made of the chemical, and physical actions that occur or the effects of these actions on the properties of the metal. It would seem necessary in any successful study of metal fluxes

Jan 10, 1920

By W. B. Vietz, C. W. Hill, T. P. Thomas

FLUXES, in general, may be classified according to their use as soldering, foundry or casting, and metallurgical and the chemistry of their action follows quite closely this division. The term foundry or casting fluxes, as used here, refers to the substances added to molten metals, preparatory to casting into molds or ingots, with the object of removing small amounts of impurities that have been introduced in handling or melting the metal, which was placed in a fair state of purity by the previous refining or metallurgical processes. The sources of these impurities are the oxide coating on the surface of the ingots, material extracted or mechanically removed from the crucible or furnace wall, and those formed by the reaction of the molten metal with the heating gases or furnace atmosphere. As commonly used, the term fluxes is applied to such materials as ammonium chloride, zinc chloride, salt, borax, and boric oxide. A second class of materials, usually called deoxidizers, includes substances such as metallic phosphides, sub-oxides, carbides, and bo-rides, that reduce the metallic oxides present in the metal. A third class includes various compounds that arc molten and non-volatile at the temperature of the molten metal and are used primarily to protect the surface of the metal from the action of the furnace or exterior atmosphere; to this class belong such mixtures as lime and fluorspar, lime and soda ash, various minerals, etc. In some cases these protective layers may act in a manner similar to the metallurgical fluxes and dissolve or unite with the oxide impurities of the metal, but as generally employed this latter action is negligible since there is little opportunity for the coverings to come into contact with more than the surface of the metal, and hence they arc without action on the body of the molten mass. The use of fluxes is the result of factory experience and tradition, but an extensive study has not been made of the chemical and physical actions that occur or the effects of these actions on the properties of the metal. It would seem necessary in any successful study of metal fluxes to determine not only what impurities are present in metals melted under

Jan 1, 1921

By R. D. Pehlke, J. V. Gluck

AS a portion of a general study of liquid-metal thermodynamics, high-temperature galvanic cells were used to study the effect of added dilute solutes on the activity of zinc in dilute solution with molten bismuth in the range 450° to 650°C. 1,2 The cells were of the type The experimental procedures have been described previously.1 In the course of studies conducted in the bismuth-rich corner of the systems Bi-Zn-Au and Bi-Zn-Cu, marked discontinuities were observed in the electromotive force-temperature relations for a number of the experimental compositions. Above the discontinuity temperatures, the relations, which were linear, exhibited slopes similar to the binary alloy of the same mole fraction zinc, as shown in Figs. I and 2. Below the discontinuity temperatures, the slopes were markedly different, but the relations remained linear. In general, as the amount of the third eletnent was increased, the slope of the lower portion of the relations tended to become less positive. The slopes of electromotive force-temperature relations reflect the entropy of mixing of zinc and, therefore, the occurrence of a discontinuity marks the transition between two different equilibrium situations involving the solution of zinc. A number of other investigators3-5 have used such observations to determine liquidus boundaries in binary alloys. Since the upper portions of the ternary electromotive force-temperature relations of this study had the same slopes as the binary alloys, the discontinuities are interpreted as marking the transition between the single-phase liquid region and the underlying two- and three-phase regions. Reference to the Zn-Bi equilibrium diagram6 confirms that the binary alloys were single-phase liquids at the experimental temperatures. Fig. I shows the electromotive force-temperature relations for the alloys containing Bi-Zn-Au and Fig. 2 shows similar relations for the Bi-Zn-Cu alloys. In the lower portion of each figure, the temperature of the discontinuity is plotted vs the mole fraction of the added solute at the various levels of zinc concentra- tion. Cross-plots from these curves at constant temperature permitted the construction of the partial liquidus surface isotherms shown in Figs. 3 and 4.

Jan 1, 1967

By Clarence W. Balke

Small buttons of fused tantalum have been produced by are fusion in a vacuum, by drawing an arc between sticks of pressed tantalum and a tantalum-faced water-cooled copper block. However, ingots of appreciable size can be produced only by the heat-treatment of bars pressed from powder. The following outline covering the production of finished bars of tantalum by the methods of powder metallurgy is also used for the production of columbium, taking into account the difference in the melting points of these two metals. Pressing the Powder With possibly a few exceptions, a pressing operation is one of the essential steps in the practice of powder metallurgy. In fact, the author's experience with a number of high-melting-point metals and with numerous types of hard carbide compositions has led him to believe that this operation is often one of the most important in the entire process, and frequently one of the most difficult to carry out in a satisfactory manner. Defects due to improper pressing can readily lead to a defective finished product. It is the author's opinion that rarely is a bar or other article pressed from metal powder in such a way that all parts of the piece are uniformly pressed. The nearest approach to uniformity of pressing is possibly attained when the powder is contained in a flexible receptacle, such as rubber, and is pressed under a liquid by hydrostatic pressure. However, this method is not generally applicable. Hydraulic pressing in steel dies where one or two punches are forced into the die must usually be resorted to. As the pressure in such a die is built up, the powder begins to cling to the walls of the die with a tenacity dependent upon the nature of the powder, and this results in a bridging action, so that the layers of powder adjacent to the moving punch are pressed more heavily than those further removed in the mass. Frequently, as the pressure is carried higher, there may be a mass slippage of the powder upon itself, with the result that slip cracks are formed within the pressed

Jan 1, 1938

THERE is probably no phase of basic open-hearth steelmaking that is more of an art and less of a science than mold and pouring practice. It varies widely from plant to plant; consequently it is obviously impossible to set down in detail in this chapter the many ramifications of practice that are now used. The discussion that follows therefore attempts only to give an outline of the more common methods, with examples sufficient to indicate some of the variations in procedure, and to emphasize a few of the many underlying problems that face the open-hearth operator at the pouring platform. MOLD DESIGN Ingot molds are hollow castings of considerable wall thickness. Despite this, non-uniformity in wall thickness should be strictly avoided to prevent the setting up of unnecessary stresses. Molds are cast in various forms, sizes, and shapes depending on the type of steel, and on whether the ingot is to be withdrawn from the mold or the mold from the ingot. The selection of ingot-mold material, which is usually cupola or blast-furnace iron containing approximately 3.5 per cent carbon, 1 per cent silicon, 0.9 per cent manganese, 0.2 per cent phosphorus, and 0.07 per cent sulphur, is governed by numerous considerations that affect mold life. (1) Factors in addition to wall thickness that should be given primary consideration at the foundry are casting skin, shrinkage stresses, and casting temperature. Factors in Mold Design. In use, mold thickness is of greatest importance, for it must be heavy enough to freeze the molten metal rising in the mold and to reduce the temperature of the steel below that of the melting point of cast iron to prevent the inner surface of the mold from melting, which would result in the welding of the ingot to the mold. The skin of an ingot, which solidities immediately upon contact with the relatively cold walls of the mold, must soon become thick enough to contract on the fluid mass and pull away slightly from the sides of the mold. The separation of the ingot from the mold depends entirely on the heat taken up by the mold from the steel.

Jan 1, 1944

By Clarence W. Balke

Small buttons of fused tantalum have been produced by are fusion in a vacuum, by drawing an arc between sticks of pressed tantalum and a tantalum-faced water-cooled copper block. However, ingots of appreciable size can be produced only by the heat-treatment of bars pressed from powder. The following outline covering the production of finished bars of tantalum by the methods of powder metallurgy is also used for the production of columbium, taking into account the difference in the melting points of these two metals. Pressing the Powder With possibly a few exceptions, a pressing operation is one of the essential steps in the practice of powder metallurgy. In fact, the author's experience with a number of high-melting-point metals and with numerous types of hard carbide compositions has led him to believe that this operation is often one of the most important in the entire process, and frequently one of the most difficult to carry out in a satisfactory manner. Defects due to improper pressing can readily lead to a defective finished product. It is the author's opinion that rarely is a bar or other article pressed from metal powder in such a way that all parts of the piece are uniformly pressed. The nearest approach to uniformity of pressing is possibly attained when the powder is contained in a flexible receptacle, such as rubber, and is pressed under a liquid by hydrostatic pressure. However, this method is not generally applicable. Hydraulic pressing in steel dies where one or two punches are forced into the die must usually be resorted to. As the pressure in such a die is built up, the powder begins to cling to the walls of the die with a tenacity dependent upon the nature of the powder, and this results in a bridging action, so that the layers of powder adjacent to the moving punch are pressed more heavily than those further removed in the mass. Frequently, as the pressure is carried higher, there may be a mass slippage of the powder upon itself, with the result that slip cracks are formed within the pressed

Jan 1, 1938

By James Aston

THE origin of wrought iron may be taken as coincident with the earliest record of ferrous products. The limitations of primitive methods of manufacture undoubtedly resulted in a material conforming to the general characteristics of what we now classify as wrought iron. Iron has been known from prehistoric times. It is frequently mentioned in Egyptian literature, and some samples in the British Museum are believed to date from 3733 B. C. Iron instruments, tools and weapons were used in Greece in 1400 B. C., and in Assyria and. Italy in 1100 B. C. History records their use in Central and Western Europe in 1000 B. C. And in Styria and Carinthia before the Christian era. The noted Pillar of Delhi is generally assumed to date from 400 A. D. The use of iron was general in Europe in the Roman Empire, and heat treatment of weapons and tools was then practiced. All of this early iron was the result of direct reduction from the ore. It serves to illustrate the ease with which the extraction may be effected, and to point out the well known principle that a malleable product of relatively high purity may be produced from high-grade iron ore at temperatures well below the fusion point of-the metal. The fact is also emphasized that there is no novelty in the seemingly ideal and constantly recurring attempts to effect direct reduction. Economic and engineering considerations have been dominant factors in dictating today's two-step practice in the manufacture of wrought iron and steel. Bear' in mind that all of this history antedated the blast furnace, and a knowledge and use of cast iron. It was only in attempts to get greater output by use of shaft-type furnaces, that cast iron was produced in Germany in the period 1300 to 1400 A. D. This was the result of longer contact with the carbon of the fuel, and higher temperatures in the furnace. This period marked the beginning of the existing two-stage operation, involving as the second step the refining of the. cast iron to a malleable product. For a time this was effected in small hearths not unlike a blacksmith's forge.

Jan 10, 1926

By Charles R. Holmes

MORE than 70 igneous pipes and dikes are known to occur in Cambrian sediments throughout an approximately circular area of about 75 sq miles in southwestern Ste. Genevieve County and southeastern St. Francois County, Mo., across the southern portion of the Farmington anticline, which is outlined in fig. 1. From evidence obtained from fossil fragments taken from some of the intrusive, and from the similarity in composition of the more basic intrusives to those of known age in surrounding states, these pipes and dikes are believed to be at least post-Devonian and probably Cretaceous in age. As first postulated by Rust, these intrusives are believed to represent explosion tubes, or diatremes, punched through great thicknesses of solid rock by gaseous pressure. The particular intrusive studied is located about 1 mile north of the small town of Avon at an elevation of 880 ft in the EM SES NE% of sec. 2, T. 35N, R. 7E. Outcrop is through the Bonneterre dolomite in two separated exposures. The larger outcrop extends east and west for about 50 ft along a tributary in a small ravine (fig. 2). The smaller exposure occurs as a few scattered patches over an area 20 ft square about 100 ft to the north. The area between the exposures is covered, but scattered patches of the Bonneterre dolomite outcrop throughout the area surrounding the diatreme. Where exposed, contact relations show the surrounding dolomite to be shattered and metamor- phosed to a fine-grained rock for a distance of 15 to 20 ft from the intrusive. The igneous rock occurs as a dark greenish-gray porphyry near the center of the diatreme and as a fine-grained, greenish-gray material containing lapilli and metamorphosed fragments of dolomite near the contact with the country rock. The most abundant original mineral of the porphyritic rock is olivine now largely serpentinized as the result of extensive hydrothermal alteration at time of emplacement. The most common constituent of the fine-grained rock, which occurs near the border of the intrusive, is calcite. Mica is a common constituent of both types of rock, occurring as tufts or

Jan 1, 1950