Search Documents

Reports on process control computer projects at the Kamioka Plant are summarized from the Japanese technical literature (see references). Fluidized Bed Roaster and Sulfuric Acid plant1 A small process control computer (Yokogawa CCS-200 with an OKITAC 5090P 8K central processor) was installed in the Kamioka smelter in the summer of 1964. A year-and-one-half installation project followed, which successfully brought the roaster and acid converters under computer control. The process plant consisted of two 130 RPD fluosolids roasters and two Monsan to acid units. The roasters are charged with lead-zinc concentrates with SO2 from the roaster processed to sulfuric acid. The computer system provides the following functions: 1) log data from the plant--the input is taken from 50 analog signals, 130 high-low digital alarm points, and 50 analog high- low alarm points; 2) set-point control on 18 control loops; 3) direct digital control (DDC) on eight control loops for which conventional controllers were difficult to adapt due to abnormal loop characteristics or delay times; 4) execution of a safe shut-down procedure

Jan 1, 1969

By John A. Wolfe

The brightest spot in the mineral economy of the Philippines is the rapid development of reserves and production of copper. If economic conditions remain favorable and the political climate is encouraging, production of this metal should increase at a rate of 25% per year for several years, long enough to rank this country as one of the major copper producers of the world. In 1965 the copper content of the Philippine concentrates was approximately 60,000 tons. It should total about 80,000 tons in 1966. A major part of the increase will come from the rich Lepanto mine located in Mountain Province, North Central Luzon. Daily production of ore increased from 1200 to 2000 tons at the end of 1965. The ore, consisting of enargite and luzonite, averages nearly 3% copper and 0.12 oz. of gold per ton. It is an under- ground operation with a cutoff grade of 2%. The ore is associated with extensive silicification under a volcanic cap rock. Further expansion to increase ore production to 2600 tpd is under way.

Jan 4, 1967

By S. Mellgren, W. Opie

AN equilibrium state of importance in the process of electrolytically depositing titanium from fused chloride electrolytes is that which exists between titanium metal, titanium dichloride, and titanium trichloride. This can be expressed by the reaction titanium concentration of the solution, temperature, and the proportion of strontium chloride and sodium chloride in the solution. Procedure The general procedure used consisted of the following steps: 1) Development of an analytical method for determining Ti+2 and total titanium. 2) Preparation of batches of fused salt solutions containing various amounts of total titanium, Ti+2 and Ti+3 3) Blending of the prepared batches and excess titanium metal in Vycor tubes and allowing the solutions to come to equilibrium. By blending, solutions with different total titanium content could be prepared and equilibrium could be approached from the high Ti+2 and low Ti+2 sides. 4) Studying the effect of titanium concentration, temperature, and the mole ratio of the solvent chlorides, SrC1, and NaC1, upon the equilibrium.

Jan 1, 1958

By Stefan Boshkov, Malcolm T. Wane

The validity and accuracy of velocity measurements underground have been questioned repeatedly by those in mine ventilation work. The general disagreement on the subject is well illustrated in an AIME publication.' Although the presence of errors is readily admitted, their magnitudes are not known and often are described by practical operators merely as "great," "small," or "of no importance." The belief that errors are of academic interest only prevails because of a justifiable claim that actual volumes of air circulated are well in excess of those required by law and safe mining practices. Poor understanding of the source and nature of errors inherent in velocity measurements, coupled with questionable determination of cross-sectional area, result in faulty techniques for the purpose of expediting ventilation surveys and render doubtful the calculated volume. Often consistency of readings is confused with accuracy. A succession of check readings showing a maximum deviation of 5 pct in the measured value of velocity usually signifies nothing more than diligent application of technique in a stable ventilating current.

Nov 1, 1955

By Y. Nakahiro

The removal of heavy metal compounds from a synthesized waste cyanide solution is achievable by a precipitation-flotation method. However, the differential separation of constituting metals by this method was thought to be very difficult. The present author found that addition of ferrous salt to the synthesized waste cyanide solution of cadmium and copper can modify the separation characteristics of these metals. In this paper, the separation of cadmium from copper in the synthesized waste cyanide water by the precipitation-flotation method is discussed. This differential flotation uses ferrous salt as a precipitant and sodium oleate as a collector. Based on a series of fundamental flotation tests, actual differential flotation tests were made. The separation of cadmium from copper in the synthesized waste cyanide water was found to be satisfactory. This method can be effective for the removal of difficult-to- separate colloidal precipitates from liquids by the sedimentation method, provided the applicability of this method to the separation of the other metals is promising. This consists of the intensive studies which have been conducted at author's laboratory.

Jan 1, 1980

By J. G. Bradley

On February 1, 1971, United States Steel Corporation, Lorain Works began operation of its first BOP facility equipped with a partial combustion gas cleaning system.- This shop consists of two 220 ton vessels. Figure I schematically describes this partial combustion gas cleaning system and highlights the necessary features for it-s safe and efficient operation. Waste gases are drawn into the membrane hood by a 2250 H.P. induced draft fan and are first quenched by the six inch bull nozzle at the top of the hood. Larger solid particles are separated from the gas in the quencher venturi and final scrubbing takes place in the P-A high energy venturi scrubber before the cleaned waste gas is burned in the flare stack. Scrubbing water is routed through a cyclone separator and then cycled into one of two 100' diameter thickeners. Underflow sludge which averages 20% solids is dewatered by 100 H.P. centrifuges. The clear overflow from the thickeners is recycled first to the P-A venturi and then to the quencher before returning to the thickeners.

Jan 1, 1972

By V. S. Rood

Typical System of Workings THE general system of workings at the Utah-Apex is similar to that found in many of the western metalliferous mines. There is a vertical three-compartment shaft extending to the surface, from which the various levels have been driven to the orebodies. The 1000-ft. (305-m.) level, about ¾ mile long, was driven as a haulage and drain adit. Geology The formation is a flat north-dipping series of alternating limestone and quartzite beds. Extensive north-south faulting and-fissuring have taken place, resulting in the formation of large replacement orebodies in the crushed zones in the limestone. The orebodies are irregular in shape and size, but follow closely the trend of the mineralizing fissures. The ore consists of galena, pyrite, sphalerite and small values in silver and gold. Large masses of non-commercial pyrite are frequently found in or adjacent' to the orebodies, and more or less pyrite is found for some distance in the walls of the orebodies. Lenticular bodies of a black pyritic shale also occur in the zones where extensive faulting has taken place.

Jan 6, 1918

By F. R. Hensel

THE present study was rude to determine the laws governing the formation of the primary? crystal structure during solidification. Most of the experiments were carried out on chill castings, but from the results it will be possible to draw certain conclusions as far as sand cast-ings are concerned. It is necessary to discuss first a number of theories, which are generally adopted for explaining the structure of an ingot. Usually, the structure FIG. 1.-VARIOUS ZONES IN A CHILL INGOT. off an ingot consists of the following three zones (Fig. 1): (1) a chill layer of small at. random oriented crystals; (2) a layer of columnar crystals; (3) a zone of equiaxed crystals. The tensile properties of the chill layer and the equiaxed range are usually much better than in the columnar range, particularly the planes that are formed by the columnar crystals growing from two sides at right angles leave low tensile properties. This is one of the reasons why colum-nar crystals in ingot structures are undesirable.

Jan 1, 1937

By R. A. Wyman

KYANITE schists in the Sudbury area have been generally described by Haw,' who has also given particuLar information on preliminary treatment of three large samples from Dryden township, Ontario.' Kyanite, garnet, biotite, quartz, and feldspar comprise the main ingredients of this ore. Kyanite is the valuable mineral. About 5½ tons of —35 +200 mesh product, made by dry rod milling, screening, and separation on the Exolon magnetic separator, were available for treatment by flotation. Magnetic separation had effectively reduced garnet and biotite so that flotation feed consisted essentially of kyanite, quartz, and feldspar, the kyanite content averaging 32 pct and representing about 86 pct of the kyanite in the original ore. Earlier work on kyanite at the Mines Branch, Ottawa, s-c employed an acid circuit, but to avoid production difficulties in the use of acids and at the same time take advantage of the fact that industrial minerals respond somewhat to soap flotation, it was decided first to investigate the higher pH levels. Exploratory tests using —65 +200 mesh feed ended with production of 96.6 pct kyanite concentrate rep-

Jan 1, 1959

By Sam F. Carter

FOR some time melters and metallurgists have recognized the fact that steels may be made to identical compositions as ordinarily analyzed, but with considerable variations in physical properties. Good melting practice signifies a combination of furnace operations that will produce steel with consistently good physical properties after proper consideration of cost, production efficiency, and chemical control. In acid practice, these operations may be classified fundamentally as: (I) the oxidizing boil, (2) recarburization and deoxidation, (3) slag adjustment, and (4) final deoxidation. These operations affect the properties of the steel through variations in the minute quantities of several microscopic, submicroscopic, and dissolved constituents, which are out of reach of ordinary analyses but are very influential upon the crystallographic slippage and the molecular cohesion of the structure. One of these constituents is the FeO left in solution in the steel. Herty has shown that steels high in dissolved FeO have decreased ductility and impact and increased hardness and electrical resistance. There is also much evidence that FeO in solution affects carbon solubility and diffusion, and consequently abnormality and carburizing behavior.

Jan 1, 1947

By D. S. Bloom

RECENTLY a report has been published on an investigation of the MO-RU system by E. Raub.' In this report it is stated that below approximately 1200°C the system consists of two terminal solid-solution phases and the intervening two-phase field; at 1200°C and above, an intermetallic compound labeled Mo,Ru, makes an appearance. Along with some other little known systems in which it was considered possible for a u phase to form, the Mo-Ru system had been under investigation in this laboratory. Since molybdenum and ruthenium have very high melting points and also since ruthenium is expensive, the investigation was confined to X-ray diffraction by sintered powder compacts. The compositions which were studied were (in atomic percentages): 75 Mo-25 Ru, 67 Mo-33 Ru, 50 Mo-50 Ru, and 25 Mo-75 Ru. All compacts were made from the pure powders, and no chemical analyses were attempted. Each compact weighed about 5 g. All annealing was done in evacuated Vycor capsules, and even though the capsules completely collapsed at 1250°C, they still admitted no air. The results of this investigation in general corroborate the work of Raub. Up to 1150°C the two terminal solutions and the intervening two-phase field were found, and at 1200°C and above an intermetallic compound was found. However, the composition limits of the compound were estimated to lie close to 70 atomic pct Mo rather than 62.5 atomic pct Mo as Raub had reported. At least the X-ray diffraction results indicated that the 75 atomic pct Mo specimen consisted of the molybdenum solid solution plus the compound, while the 67 atomic pct Mo specimen consisted of the ruthenium solid solution plus the compound and the equiatomic composition contained only very little of the compound. The most interesting observation, however, was that the diffraction pattern of the compound was similar to that of the well known u phases, except that unusually large lattice constants were indicated. The d-values, or interplanar spacings, of the diffraction lines (as produced by filtered copper KCX radiation) of the compound are given in Table I, as determined from specimens annealed at 1250°C for 9 hr and then quenched in water. Also shown are the lines of the Mn-Mo u phase as given by Decker, Waterstrat, and Kasper,' the lines of the Fe-Mo a as given by Goldschmidt," and the lines of the Mo-Ru phase multiplied by constants in order to make comparison with the Mn-Mo and Fe-Mo patterns easier. These results indicate that the compound in the Mo-Ru system is apparently isomorphous with the other o- compounds. The rather large lattice constants of the Mo-Ru a phase are acceptable in view of the comparatively large size of the constituent atoms. The data in Table I for the Mo-Ru compound check quite well with those given by Raub, not shown here, though there are some discrepancies between the two sets of data in the estimated intensities of a few lines. Although very little is known at present about this u phase, there are some things which may be pointed out, mainly in comparison with other better known u phases. Even though molybdenum and ruthenium are in the same columns in the Table of Elements as chromium and iron, respectively, the Mo-Ru u phase contains much more molybdenum than ruthenium, while the Cr-Fe u phase centers around or very nearly around the equiatomic composition; furthermore, the Mo-Ru u is stable only above approximately 1200°C, but the Cr-Fe u is stable only below about 825 °C. With respect to its being unstable below 1200°C, the Mo-Ru u is similar to the other binary molybdenum u phases in the Co-Mo and Fe-Mo systems. Similar to the latter two systems, the Mo-Ru u apparently exists over a rather narrow composition range, whereas the Cr-Fe u at lower temperatures is stable over a much wider composition range. The Mo-Ru u thus is closer to the other molybdenum u phases than to the Cr-Fe cr phase. The most striking feature of the Mo-Ru u phase, however, is the absence of any of the transition elements of the First Long Period.

Jan 1, 1956

By V. J. Sikora, W. J. McGuire

Several years ago, we used an electric analogue computer to study the effect of vertical fractures on the productivity of wells in expanding fluid-drive reservoirs. The results of this work were used both as a guide to research and as a basis for the design of actual fracturing operations. In 1958, Dyes, Kemp and Caudle' published portions of the data from this study. The results were released in 1959 to service companies for use in fracturing guides. The purpose of this note is to discuss the experimental conditions and assumptions which were made to derive the information which is already partially a matter of public record. ASSUMPTIONS This study applies to fractures which extend in a vertical plane symmetrically from the well. For simplicity, we chose to study the case of a well in a square drainage area with its fractures extending toward two of its nearest neighbors. We have assumed no migration of fluid across the boundary of this area. The quadrant shown in Fig. 1 models this system. We made the usual assumptions that the reservoir is homogeneous and isotropic, that the fluid is homogeneous and that production is effected by fluid-expansion drive. We also assumed that the fracture extends from top to bottom of the reservoir. Of more practical interest is our assumption that the fracture does not change the size of the drainage area. This premise is appropriate if all the wells in the reservoir are fractured in the same way. But where a single well is fractured, its drainage area may be enlarged at the expense of its neighbors. This could be of economic importance. The assumption that the fracture will not extend beyond the established drainage area of the well also limits the application of the results. Such long frac- tures will yield benefits in excess of those predicted here. When we assume homogeneity, we disregard the frequently observed zone of damage in the vicinity of the well. Where damage is severe, the benefits resulting from by-passing it will far exceed those predicted by this study. All comparisons were made of systems producing in the semi-steady state. By this we mean that equal volumes contributed equally to flow (pressure was dropping at a uniform rate throughout the system) when the rate of flow was observed. EXPERIMENTAL SET-UP We used the pool unit of an electric analyzer' in this study. The squase drainage system of a well was rep-

By R. F. Mehl, B. Lustman

THE formation of intermediate phase layers in cementation processes has been subjected to extensive qualitative investigation though to relatively little quantitative study; this work has recently been fully summarized by F. N. Rhines.1 It is necessary here only to enumerate the general conclusions drawn concerning the kinetic laws governing the growth of intermediate layers and to state what is known concerning the structural changes accompanying the generation of phase layers. I. When the intermediate phase is protective in type-i.e., when its density is less than that of the base metal, so that a continuous coating is formed and maintained the isothermal growth of the phase follows a simple parabolic equation: X2 = kt [I] where X is the thickness of the alloy layer, k the reaction rate constant, and t the time. The applicability of this equation to diffusion processes is tested by plotting the square of the thickness versus time, or by plotting the thickness versus the square root of time; the resultant achievement of a straight line in such. a plot has been con¬sidered sufficient proof of the validity of this equation. Exceptions have been found where liquid phases are involved in the reaction, where the diffusion layer is cracked,2 and where thin semimetallic oxide and sulphide coatings are formed on metals.3 In the first two cases the thickness increases linearly with time, and in the latter it is a logarithmic function of time. 2. The rate of thickening varies with temperature according to the Arrhenius equation k = Ae-Q/RT [2] where k is the parabolic rate constant of Eq. I, or some other rate-descriptive function, A is the action constant, e the base of natural logarithms, Q the heat of activation, R the gas constant, and T absolute temperature. This equation has been found to be generally valid except when transformations occur during reaction in either the base metal or in the reaction layer; in such instances Eq. 2 is still applicable with different values for the constants A and Q above and below the transformation temperature. 3. All phases that are stable at the temperature at which diffusion occurs will appear in the interdiffusion of two components. In some cases certain of the phases may be too thin to be observed and identified easily. Nonequilibrium phases have never been noted in thick reaction layers; i.e., layers of a thickness that may be discerned microscopically. The relative, thickness of each phase in a diffusion layer is proportional to the concentration gradient and to the rate of diffusion in that phase .4 The reaction layers tend to have a

Jan 1, 1942

By John A. Emery, Frank G. Snyder

MINING geology has a threefold objective: to guide prospecting for new ore, to evaluate known orebodies as development risks, and to supply the detailed knowledge of ore structures necessary for more economical extraction. The role of geology in exploration is well established. This article will deal solely with orebody evaluation and the application of geology to development and mining problems as practiced by St. Joseph Lead Co. in the southeast Missouri district, which for many years has supplied approximately 30 pct of U. S. lead production. The primary concern of the present discussion is geology in the district, not geology of the district. The southeast Missouri district, locally called the Lead Belt, includes parts of St. Francois, Madison, and Washington counties. The first recorded mining was about 1720 at Mine La Motte in Madison County on surface showings of lead ore. Later discoveries near Bonne Terre, twenty-five miles to the north, led to extensive prospecting and underground mining. To date the district has yielded well over 8 million tons of pig lead, valued at more than $1 billion. By far the greater part of the lead production has come from an area of 50 sq miles, centering on the city of Flat River, as shown in Fig. 1. Role of Geology in Metal Mining The history of the use of geology in the older metal mining districts follows a simple consistent pattern that may be considered in terms of four distinct phases. Each geologic phase is a response to the economic status of the mining district; each has definite characteristics setting it apart from other phases; and each passes into the succeeding phase as the mining operation gradually exhausts the large, rich, easily discovered deposits and lives upon increasingly smaller, lower grade orebodies that are less easily found. The geologic phases and their major characteristics are as follows: Period of No Organized Geologic Program: During the early history of a great metal district ore is easily found by random prospecting and wildcat drilling. Many small operators are active, as profitable mining can be done with a relatively small capital outlay and a minimum of technical staff. Mining practice consists largely of sinking a shaft on an ore showing and following the ore in sight. When the ore is exhausted or becomes unprofitable to mine, the process is repeated on a new ore showing. The miners become familiar with certain ore habits and use this practical geologic knowledge to guide mining. The method is successful as long as large tracts of virgin mineralized area are available. This phase ends when small-scale mining methods are no longer profitable and the mines become consolidated into the hands of a few operators.

Jan 1, 1957

By Benjamin Lustman, Robert F. Mehl

The study of the high-temperature oxidation of pure metals, intensively pursued experimentally since the pioneer work of Pilling and Bedworth1 and supplemented by the recent theoretical work of Wagner2 is now well advanced. The important field of low-temperature oxidation—i.e., oxidation extending only through the temper color range of thicknesses with the formation of thin oxide layers in the range from 0 to 1000-2000 ?ngstroms—has not, however, reached so satisfactory a state, owing largely to the experimental difficulties that attend the formation and study of thin films; most of the work has been performed on abraded specimens whose surface irregularities approximated the thickness of the films formed. It has been pointed out that the rates of oxidation of different crystal faces are different and that the difierence may be related to the orientation relationships that obtain between the metal crystal and the superimposed oxide crystal; it has also been suggested that this orientation dependence should manifest itself in rates of oxidation and perhaps also of corrosion in aggregates bearing preferred orientations.3'4 An attempt to measure the rates of oxidation of different crystal faces of alpha iron demonstrated this difference in rate,4 but the dependence of rate on orientation was not simple; the method of measuring thickness, consisting of a color comparison with barium stearate multi-films of known thickness, was not wholly satisfactory. For these reasons it was felt that a study of the rate of oxidation of single crystals prepared with surfaces as smooth as possible, using a sensitive method giving true film thickness, should be profitable. Copper was chosen because of the ease of reduction of the primary oxide film and because the orientation relationships between metal and oxide and the composition of the oxide films formed at low temperatures are known; for thin films formed at low temperatures, Cu2O alone occurs.22-24 Experimental Procedure Various methods of surface preparation were attempted in order to obtain a surface that would oxidize uniformly and repro-ducibly. Electrolytic polishing by the method of Jacquet5 and electrolytic and mechanical polishing followed by annealing in vacuum and in purified hydrogen at various temperatures were tested. The procedure finally adopted consisted in a fine metallographic polish followed by an anneal in purified hydrogen at temperatures of 900° to 1000°C. for 12 hr. or more. The surface so produced was very bright and smooth, with no trace of specular etching (though some grain-boundary etching was observed); indeed, fine scratches produced by the final polish were entirely removed by the high-temperature anneal. After this treatment, the specimens were cooled in hydrogen to room temperature and placed in the oxidation furnace, where

Jan 1, 1941

By Benjamin Lustman, Robert F. Mehl

The study of the high-temperature oxidation of pure metals, intensively pursued experimentally since the pioneer work of Pilling and Bedworth1 and supplemented by the recent theoretical work of Wagner2 is now well advanced. The important field of low-temperature oxidation—i.e., oxidation extending only through the temper color range of thicknesses with the formation of thin oxide layers in the range from 0 to 1000-2000 ?ngstroms—has not, however, reached so satisfactory a state, owing largely to the experimental difficulties that attend the formation and study of thin films; most of the work has been performed on abraded specimens whose surface irregularities approximated the thickness of the films formed. It has been pointed out that the rates of oxidation of different crystal faces are different and that the difierence may be related to the orientation relationships that obtain between the metal crystal and the superimposed oxide crystal; it has also been suggested that this orientation dependence should manifest itself in rates of oxidation and perhaps also of corrosion in aggregates bearing preferred orientations.3'4 An attempt to measure the rates of oxidation of different crystal faces of alpha iron demonstrated this difference in rate,4 but the dependence of rate on orientation was not simple; the method of measuring thickness, consisting of a color comparison with barium stearate multi-films of known thickness, was not wholly satisfactory. For these reasons it was felt that a study of the rate of oxidation of single crystals prepared with surfaces as smooth as possible, using a sensitive method giving true film thickness, should be profitable. Copper was chosen because of the ease of reduction of the primary oxide film and because the orientation relationships between metal and oxide and the composition of the oxide films formed at low temperatures are known; for thin films formed at low temperatures, Cu2O alone occurs.22-24 Experimental Procedure Various methods of surface preparation were attempted in order to obtain a surface that would oxidize uniformly and repro-ducibly. Electrolytic polishing by the method of Jacquet5 and electrolytic and mechanical polishing followed by annealing in vacuum and in purified hydrogen at various temperatures were tested. The procedure finally adopted consisted in a fine metallographic polish followed by an anneal in purified hydrogen at temperatures of 900° to 1000°C. for 12 hr. or more. The surface so produced was very bright and smooth, with no trace of specular etching (though some grain-boundary etching was observed); indeed, fine scratches produced by the final polish were entirely removed by the high-temperature anneal. After this treatment, the specimens were cooled in hydrogen to room temperature and placed in the oxidation furnace, where

Jan 1, 1941

By Klaus Schwerdtfeger

The rate of formation of silicon monoxide from silica spheres has been measured at 1500°C in H2, H2-H2O, H2-He, H2-Ar, and CO-CO2 gas mixtures. Indications are that in the hydrogen-containing gases the reaction rate is mainly determined by convective diffz~sion. In the CO-CO2 mixtures the rate approches a constant value which is independent of sphere diometer (and gas velocity). This suggests that a surface reaction becomes rate controlling in CO-CO2 gas. WHENEVER silica is exposed at elevated temperature to a strongly reducing atmosphere there occurs, inevitably, a volatilization of silica by the formation of gaseous silicon monoxide. Because of the importance of this reaction in metallurgical processes and laboratory experiments, its kinetics were studied in the present work. EXPERIMENTAL The spheres made of vitreous silica were suspended by a molybdenum wire in the hot zone of a gas-tight high-purity recrystallized alumina furnace tube of 3.1 cm internal diam and 100 cm length. Molybdenum wire resistance heating was used. A purified H2, H2-H2O, H2-He, H2-Ar, or CO-CO2 gas mixture was passed through the tube, from top to bottom. The amount of silicon monoxide formed was determined by weighing the silica balls before and after the experiments. The silica balls were made from commercially available translucent fused quartz glass. In experiments with hydrogen-containing gases the silica stayed vitreous during the experiment, whereas in experiments with CO-CO2 mixtures, which were performed over longer times, the balls were always crystallized to cristobalite (as determined by X-ray examination) at the surface. Constant-pressure head capillary flowmeters were used to control the composition of H2-He, H2-Ar, and CO-CO2 gas mixtures. The oxygen and water vapor were removed from the gases containing hydrogen by passage through columns containing platinized asbestos (450°C) and an-hydrone. The CO was purified from O2 and CO2 by passing it through activated copper (200°C) and through ascarite. The H2-H2O gas mixtures were prepared by passing purified Hz through a mixture of oxalic acid dihydrate and anhydrous oxalic acid held at a constant temperature in a water bath. The equilibrium water vapor pressures of oxalic acid dihydrate-anhydrous oxalic acid mixtures were taken from the available data.1 The furnace system was checked for sufficient gas tightness at regular intervals. As an additional check, the H2O and CO2 contents were measured in the exit gas and were found to agree closely with the metered contents when H2-H2O or CO-CO2 mixtures were used. When purified H2 was used, H2O pressures found in the exit gas were always below 0.1 mm Hg. These contents originate either from an incomplete reoxidation of silicon monoxide in the cold part of the furnace or from small leaks which cannot be avoided. If the latter is the case, such small uncontrolled H2O contents decrease the partial pressure of SiO in equilibrium with SiO2 by less than about 7 pct, which is considered small in comparison to other experimental uncertainties. The temperature of the furnace was controlled automatically in the usual manner. The reported temperature was measured with a Pl-Pt/l0pct Rh thermocouple and was accurate to ± 5°C. TRANSPORT-CONTROL LED RATE OF REDUCTION The gaseous convective diffusion from the surface of a sphere can be predicted from the semiempirical relationship obtained by Ranz and Marshall2 in a study of the evaporation of water and benzene drops in air. The following equation applies:

Jan 1, 1967

By Robert R. Turner, Arthur R. MacPherson

This chapter reviews the steps which should be taken from the time it is decided to consider autogenous grinding in the development of a new ore deposit or the expansion of an existing plant up until the purchase of the new autogenous mills. In this case the term autogenous includes semi -autogenous, secondary pebble mills, and lump milling as well as fully autogenous grinding systems. Also, both wet and dry grinding alternatives have been included. Before the test program it must be decided how many bulk samples are required to properly assess the autogenous grinding possibilities of the deposit. Also, a decision must be made on where and how the samples are to be ground i.e. pilot mill at site or in established location, wet and or dry grinding, etc. In the test program itself, certain fundamental data must be obtained. The testing should include enough work to determine whether fully autogenous or semi-autogenous grinding should be used and what type produces best power efficiency. Also, all the other pertinent data should be collected such as power; tonnages; feed, charge, and product sizing; circulating loads, etc. If a secondary mill is required to produce a final grind the decision on whether a pebble or ball mill should be used may require additional test work. Finally, the concentration of the mineral may play an important part in selection of the circuit and should become a part of the final testing once the grinding has been established.

Jan 1, 1978

By Frank R. Van Horn

In the summer of 1908, R. B. Cochran, Superintendent of the Compania Metalurgica Mexicana at Sierra Mojada, Mexico, presented to the Department of Geology and Mineralogy at Case School of Applied Science an interesting series of silver-, copper-, and lead-ores from the Veta Rica mine. These ores contained several interesting minerals which were associated in a somewhat peculiar manner, so that I was impelled to make a closer study of their occurrence. The investigation has brought out several new facts concerning the geology of the district and the geological occurrence of the ores, and therefore has seemed worthy of record. Two papers have been published previously about the region, one by Chisml in 1887, and the other by Malcolmson² in 1902. These articles, however, treat of the district more from the stand-point of the metallurgist and mining engineer, and not much attention is devoted to its mineralogy and economic geology. 11. Geographical Location of the District. The Sierra Mojada is situated in the extreme western part of the State of Coahuila, near the Chihuahua boundary. It is reached best via the Mexican Central railroad from El Paso, Tex., to Escalon, Chihuahua, a distance of 494 miles. From this point, a branch line, the Mexican Northern railroad, runs 78 miles in a NE. direction to the mines, which are its northern terminus. The railroad was built about 1890, practically on account of the Sierra Mojada mining-district.

Jan 1, 1913

By D. R. Uhlmann, T. P. Seward, O. Chalmers

A magnetic field has been used to damp out liquid convection during the solidification of castings. Ingots of Al-2 pct Cu were poured from various sperheats (10" to 65°C) into a room-temperature graphite mold located between the poles of an electromagnet. The effect on ingot structure of varying the strength and time of application of the magnetic field was investigated, and the results are interpreted in light 01- current theories of ingot structure. In the solidification of alloy systems, thermal gradients in the melt and differences in density of the constituents are expected to produce convective motion in the liquid. The thermal convection caused by temperature gradients should be present during the freezing of both alloys and pure materials, while the solute convection caused by density differences should be of concern only for alloys. The possible influence of this natural convection on the structure of castings has been discussed by Ruddle,' Chalmers, and Tiller. More recently, an experimental investigation of such effects was carried out by Cole and Bolling. These workers took stationary molds containing lead- and tin-based alloys and. using a brine solution. quenched them from various superheats above their respective liquidus temperatures. When grids were placed across the mold diameter to suppress convection, the grid region was later observed to contain a larger percentage of columnar grains than other parts of the casting or than similar castings poured without the grids present. From thermocouple measurements, they found the temperature in the grid region to be higher than that in the region outside the grids throughout the freezing process, and concluded that convection should be an important mode of heat transfer in normal castings. In addition to such convection arising from thermal gradients or differences in density of the constituents, a further source of convective motion, which we shall call "momentum convection", may be particularly important in small (laboratory-size) castings. By this term we refer to the convective motion produced in the initial pouring process, a motion which is damped out as the linear momentum and angular momentum of the liquid are dissipated. Besides these sources of convection, which are present to some extent in all castings. external influences may also be effective in producing convective motion. Examples of such "forced" convection which have been discussed in the literature include stirring the melt, shaking the mold, rotating the mold, and so forth The purpose of the present study was to examine the effect of convection on the structure of castings poured into a cold mold. In this work, a magnetic field was employed to damp out the convective motions within the liquid, and hence control the extent of con- The effect of a magnetic field on convective currents in a conducting liquid is to induce eddy currents which oppose and damp out the convective motion. vection. The technique of magnetic damping was previously used by Utech and F1emings" in their study of convective effects on impurity banding and other substructure in alloy crystals grown unidirectionally from the melt. In their investigation, fields as small as 200 gauss were found to be effective in damping the convection currents which influence the banding. I) EXPERIMENTAL TECHNIQUE In the present study, alloys of A1-2 wt pct Cu were poured into a room-temperature graphite mold. The mold, in the shape of a circular cylinder, 2 in. ID, 2-3/4 in. OD, 5 in. inside height, and 5-1/2 in. outside

Jan 1, 1967