Search Documents

By Avnulf Muan, Egil Aukrust

Activity-composition curves jor cobalt oxide and manganese oxide in solid solutions with spinel-type structure have been determined by studying the equilibrium between the spinel phase and a coexisting solid-solution phase in the tewzperature range 1100" to 1400"C. Within limits of experimental error, the system displays the behavior of a regular solution. The excess integral free energy of mixing is represented by the equation . The standard free energy of formation of cobalt manganite, CoMn,O,, from the oxide components COO mzd Mn2OS at 1200°C is calculated to be -8.6 kcal. AMONG the technologically and theoretically most important oxide phases are those which crystallize with the same structure type as the mineral MgO . A120,. Although the name spinel originally was used only for this mineral, the term is generally used today to designate the whole group of oxide phases with this same structure type. It is in this wider meaning that the term is being used in the present paper. The previous literature on spinels is very extensive. There are two aspects of spinels which have attracted particular attention: the structure, including the nature and distribution of the cations present, and the physical properties (electric, magnetic). The status of knowledge in these fields has been well-summarized in recent review articles.1'2 By contrast, thermodynamic properties of spinels are virtually unknown. Delineation of the activity-composition curve over the whole composition range of a solid-solution series with spinel-type structure is the objective of the present work. The system at elevated temperatures (>1000"C) constitutes such a series. The activity-composition curves for this system can be calculated from a study of the equilibrium between the above spinel solid solution and a solid solution (Co,Mn)O with sodium chloride-type structure. Data for the latter solid solution have become available recently.3 The system, in contact with metallic CO at 1200°C, obeys Raoult's law. The determination of the activity-composition curve for the spinel phase is based on the following relations. Consider the reduction-oxidation equilibrium for cobalt ions according to the equation: Because it is impossible in practice to measure single activities of electrically charged constituents, we will treat the equilibria in terms of electrically neutral components. Eq. [I] can then formally be written as follows: where and the activities of cobalt oxide in the (Co,Mn)O and the spinel solid-solution phases, respectively, K is a constant at constant temperature, and Pa is the oxygen pressure of the gas phase. The numerical value of K can be determined from a determination of the oxygen pressure P& for the equilibrium coexistence of Cos04 and COO in the binary system Co-0. Under these circumstances be set equal to 1, and hence K = [Po Eq. [3] can therefore be written

Jan 1, 1964

By L. P. Davidson

ThE new electrolytic zinc plant of the American Zinc Company of Illinois commenced operation in April 1941. The simple flowsheet using the standard current density and the economic reasons that dictated it are given herewith. The Evans-Wallower Zinc Co. built an electrolytic zinc plant at Monsanto, Ill., in 1929 and operated it for about two years. The plant stood idle from 1932 and was purchased by the American Zinc Co. in 1940. Because of the condition of the equipment, excepting the motor generator set, a complete rebuilding was necessary. The Fairmont City plant of the American Zinc Co. could treat the leach residues, the purification cake and the skimmings from the melting furnace in its various plants. This possibility permitted a simple flowsheet with good economic results. The flowsheet is shown in Fig. I. The calcined concentrates are leached in mechanically agitated tanks with spent electrolyte and such ferric iron solution as necessary. When the acid has been neutralized and the iron coagulated, the fluid is discharged to settling tanks. The underflow from these thickeners is filtered on a Moore filter; the filter cake leaves the plant for retreatment and the filtrate joins the thickener overflow. Zinc dust is added to this solution until the copper and cadmium are precipitated. The pulp is filtered through Shriver presses, which deliver the purified solution to stor- age tanks, and the copper-cadmium-zinc cake is shipped for retreatment and recovery of these three metals. The purified solution is electrolyzed; the regenerated acid is returned for use in the leaching plant and the cathode zinc, after stripping, goes to the melting furnace, from which it is cast in slabs. The skimmings from the melting furnace are shipped to the Fairmont City plant for reduction to metal in the retort furnaces. The choice of this simple flowsheet was made possible only because of the facilities of the Fairmont City plant. The long leaching pried, with high acid content and high temperature which characterize the high-density process, gives a higher zinc extraction but also dissolves more impurities, which must be removed. The same is true to a lesser degree of the multi-step leaching of the western low-density plants. By the sacrifice of some initial extraction, solutions can be obtained that are relatively easy to purify and give good ampere efficiency. This loss in initial extraction is made up in the retreatment of the residues in the Waelz plant. The impurities that accompany the zinc thus extracted are inconsequential when the Waelz product is treated in a distillation plant. It was recognized that this flowsheet would require a somewhat greater amount of sulphuric acid—-eithcr as acid or as sulphate sulphur in the calcine—because of poorer washing. The sulphuric acid plant at Fairmont City could deliver 60" Bè. acid to compensate for the sulphate loss and the cost would be less than the cost of more intensive washing.

Jan 1, 1943

By L. P. Davidson

THE new electrolytic zinc plant of the American Zinc Company of Illinois commenced operation in April 1941. The simple flowsheet using the standard current density and the economic reasons that dictated it are given herewith. The Evans-Wallower Zinc Co. built an electrolytic zinc plant at Monsanto, Ill., in 1929 and .operated it for about two years. The plant stood idle from 1932 and was purchased by the American Zinc Co. in 1940. Because of the condition of the equipment, excepting the motor generator set, a complete rebuilding was necessary. The Fairmont City plant of the American Zinc Co. could treat the leach residues, the purification cake and the skimmings from the melting furnace in its various plants. This possibility permitted a simple flowsheet with good economic results. The flowsheet is shown in Fig. I. The calcined concentrates are leached in mechanically agitated tanks with spent electrolyte and such ferric iron solution as necessary. When the acid has been neutralized and the iron coagulated, the fluid is discharged to settling tanks. The underflow from these thickeners is filtered on a Moore filter; the filter cake leaves the plant for retreatment and the filtrate joins the thickener overflow. Zinc dust is added to this solution until the copper and cadmium are precipitated. The pulp is filtered through Shriver presses, which deliver the purified solution to storage tanks, and the copper-cadmium-zinc cake is shipped for retreatment and recovery of these three metals. The purified solution is electrolyzed; the regenerated acid is returned for use in the leaching plant and the cathode zinc, after stripping, goes to the melting furnace, from which it is cast in slabs. The skimmings from the melting furnace are shipped to the Fairmont City plant for reduction to metal in. the retort furnaces. The choice of this simple flowsheet was made possible only because of the facilities of the Fairmont City plant. The long leaching period, with high acid content and high temperature which characterize the high-density process, gives a higher zinc extraction but also dissolves more impurities, which must be removed. The same is true to a lesser degree of the multi-step leaching of the western low-density plants. By the sacrifice of some initial extraction, solutions can be obtained that are relatively easy to purify and give good ampere efficiency. This loss in initial extraction is made up in the retreatment of the residues in the Waelz plant. The impurities that accompany the zinc thus extracted are inconsequential when the Waelz product is treated in a distillation plant. It was recognized that this flowsheet would require a somewhat greater amount of sulphuric acid-either as acid or as sulphate sulphur in the calcine-because of poorer washing. The sulphuric acid plant at Fairmont City could deliver 60° Be. acid to compensate for the sulphate loss and the cost would be less than the cost of more intensive washing.

Jan 1, 1942

By L. P. Davidson

THE new electrolytic zinc plant of the American Zinc Company of Illinois commenced operation in April 1941. The simple flowsheet using the standard current density and the economic reasons that dictated it are given herewith. The Evans-Wallower Zinc Co. built an electrolytic zinc plant at Monsanto, Ill., in 1929 and operated it for about two years. The plant stood idle from 1932 and was purchased by the American Zinc Co. in 1940. Because of the condition of the equipment, excepting the motor generator set, a complete rebuilding was necessary. The Fairmont City plant of the American Zinc Co. could treat the leach residues, the purification cake and the skimmings from the melting furnace in its various plants. This possibility permitted a simple flowsheet with good economic results. The flowsheet is shown in Fig. I. The calcined concentrates are leached in mechanically agitated tanks with spent electrolyte and such ferric iron solution as necessary. When the acid has been neutralized and the iron coagulated, the fluid is discharged to settling tanks. The underflow from these thickeners is filtered on a Moore filter; the filter cake leaves the plant for retreatment and the filtrate joins the thickener overflow. Zinc dust is added to this solution until the copper and cadmium are precipitated. The pulp is filtered through Shriver presses, which deliver the purified solution to storage tanks, and the copper-cadmium-zinc cake is shipped for retreatment and recovery of these three metals. The purified solution is electrolyzed; the regenerated acid is returned for use in the leaching plant and the cathode zinc, after stripping, goes to the melting furnace, from which it is cast in slabs. The skimmings from the melting furnace are shipped to the Fairmont City plant for reduction to metal in the retort furnaces. The choice of this simple flowsheet was made possible only because of the facilities of the Fairmont City plant. The long leaching period, with high acid content and high temperature which characterize the high-density process, gives a higher zinc extraction but also dissolves more impurities, which must be removed. The same is true to a lesser degree of the multi-step leaching of the western low-density plants. By the sacrifice of some initial extraction, solutions can be obtained that are relatively easy to purify and give good ampere efficiency. This loss in initial extraction is made up in the retreatment of the residues in the Waelz plant. The impurities that accompany the zinc thus extracted are inconsequential when the Waelz product is treated in a distillation plant. It was recognized that this flowsheet would require a somewhat greater amount of sulphuric acid-either as acid or as sulphate sulphur in the calcine-because of poorer washing. The sulphuric acid plant at Fairmont City could deliver 60° Bé. acid to compensate for the sulphate loss and the cost would be less than the cost of more intensive washing.

Jan 1, 1942

By L. P. Davidson

The new electrolytic zinc plant of the American Zinc Company of Illinois commenced operation in April 1941. The simple flowsheet using the standard current density and the economic reasons that dictated it are given herewith. The Evans-Wallower Zinc Co. built an electrolytic zinc plant at Monsanto, 111., in 1929 and operated it for about two years. The plant stood idle from 1932 and was purchased by the American Zinc Co. in 1940. Because of the condition of the , equipment, excepting the motor generator set, a complete rebuilding was necessary. The Fairmont City plant of the American Zinc Co. could treat the leach residues, the purification cake and the skimmings from the melting furnace in its various plants. This possibility permitted a simple flowsheet with good economic results. The flowsheet is shown in Fig. I. The calcined concentrates are leached in mechanically agitated tanks with spent electrolyte and such ferric iron solution as necessary. When the acid has been neutralized and the iron coagulated, the fluid is discharged to settling tanks. The underflow from these thickeners is filtered on a Moore filter; the filter cake leaves the plant for retreatment and the filtrate joins the thickener overflow. Zinc dust is added to this solution until the copper and cadmium are precipitated. The pulp is filtered through shriver presses, which deliver the purified solution to stor- age tanks, and the copper-cadmium-zinc cake is shipped for retreatment snd recovery of these three metals. The purified solution is electrolyzed; the regenerated acid is returned for use in the leaching plant and the cathode zinc, after stripping, goes to the melting furnace, from which it is cast in slabs. The skimmings from the melting furnace are shipped to the Fairmont City plant for reduction to metal in the retort furnaces. The choice of this simple flowsheet was made possible only because of the facilities of the Fairmont City plant. The long leaching period, with high acid content and high temperature which characterize the high-density process, gives a higher zinc extraction but also dissolves more impurities, which must be removed. The same is true to a lesser degree of the multi-step leaching of the western low-density plants. By the sacrifice of some initial extraction, solutid'ns can be obtained that are relatively easy to purify and give good ampere efficiency. This loss in initial extraction is made up in the retreatment of the residues in the Waelz plant. The impurities that accompany the zinc thus extracted are inconsequential when the Waelz product is treated in a distillation plant. It was recognized that this flowsheet would require a somewhat greater amount of sulphuric acid—either as acid or as sulphate sulphur in the calcine—because of poorer washing. The sulphuric acid plant at Fairmont City could deliver 60" BC. acid to compensate for the sulphate loss and the cost would be less than the cost of more intensive washing.

Jan 1, 1944

By Robert E. Green, P. W. Kingman

Application of a constant geometry compression test to single crystals of aluminum of selected diameters from 1/4 to 1/64 in. showed the presence of a diameter-dependmt size effect. The most pronounced effects were found in those crystals oriented for single slip, while for specimens possessing orientations in the comers of the standard stereographic triangle virtually no size effect was exhibited. The yield stress of the crystals oriented for single slip was found to increase with decrease in specimen diameter, while the strain-hardening rate was found to be lower for the smaller specimens. The experimental results are in general agreement with those of other investigators obtained from lensile tests on copper and aluminum crystals. THE earliest systematic investigation of a possible size effect on the plasticity of metals was that of no,' who in 1926 performed tensile tests on cylindrical aluminum single crystals with diameters of 3 to 8 mm. Ono concluded that the gross stress-strain curve did not show a diameter dependence, but that the resistance to slip for strains of 0.1 pet and less appeared higher for 3-mm-diam crystals than for larger sizes. Later studies of aluminum by Maddin et al2 tentatively concluded that a size effect exists, but the conclusions were again open to question because of inconsistencies in the experimental data. Wu and Smoluchowski3 had previously shown that the slip system activated in a single-crystal sheet specimen of aluminum is a function of the specimen cross section in the slip direction, but no stress-strain data were obtained. Subsequently Fleischer and Chalmers4 studied the effect of the length of the slip direction of the primary-slip system on the stress-strain curve by testing aluminum crystals with geometrically dissimilar cross sections. In the course of this investigation a size effect was indicated in rather large crystals; however, the number of these tests was small. Other investigators have indicated that a size effect in aluminum is appreciable only for diameters of 0.5 mm or less.5, 6 Size-effect studies have also been carried out on copper crystals, the most detailed being that of Suzuki et a1.7 who performed tensile tests on specimens of many diameters ranging from 2 to 0.12 mm. Suzuki found a strong size dependence in the easy-glide region, both the extent of the easy glide and the hardening rate in easy glide were size-dependent, and the size effect was found to be orientation-dependent. Suzuki's results are in agreement with the less extensive observations of Pater-sonB and those of Garstone et al.9 A size effect was found by Rebstock using tubular copper crystals.'0 Size effects have also been noted in a brass,6, 11 in cadmium,12'19 and in hexagonal crystals.14 All the previously cited works have been entirely concerned with the variation of specimen cross section. The effects of specimen length and the change of specimen geometry which results from using progressively thinner specimens while maintaining the same specimen length have been largely ignored. A theoretical discussion of the effects of specimen length and geometry has been given by Hauser and Jackson,15 who predict a grip effect on easy glide as a function of specimen geometry provided that the specimen dimensions are large compared with the spacing between the slip bands, and by Fleischer and Chalmers,18 whose analysis of grip effects resulting from lattice rotation predicts an increase in easy glide with an increase in specimen length. A study of size and geometry effects in aluminum crystals by Kitajima and shimba17 indicated increasing amounts of easy glide in specimens of increasing length and identical cross section, and nearly identical stress-strain curves for specimens of different sizes having constant length-to-diameter ratios. Since the present study is primarily concerned with diameter dependence, the following factors were taken into account: specimen material, specimen geometry, testing method, range of sizes to be tested, and possible influence of surface and volume effects. Aluminum was chosen because of the present lack of conclusive results and the seeming possibility of size effects at relatively large diameters, the

Jan 1, 1964

By Harrison R. Cooper

Computer process analysis and control techniques are overcoming major hurdles to acceptance in the mineral industry. With the growing list of new advances characteristic of a rapidly maturing discipline, management of the companies on the leading edge are keenly aware of the advantages of using computer methods in process applications. Significant advancement is already evident in such technical areas as operations research, mathematical modeling, statistical methods, and computer-based procedural techniques. The early advances during the past decade are already documented in prior symposium proceedings of this series. Thus, the currently active areas of the advancing technology are emphasized here. This section deals with applications in pyrometallurgical and kiln processes. The two sections which follow deal with concentrating operations from two points of view: 1) mathematical modeling, and 2) on-line control. In the metallurgical field, emphasis on developing effective process computer applications for the steel industry began in the late 1950's. Simulation techniques also received substantial attention. The steel industry was soon joined by the cement industry in the development of computer methods for process applications. Computers were in use for feed-material blending and kiln control in the early 1960's. Computer development in other pyro processes, such as aluminum reduction and glass-making, also marked significant advances by the mid 1960's. Aluminum smelter potline control is a nearly universal application at this point, and the development of glass furnace computer process control represented a recent important technical advance in digital control techniques. Steel Hot strip rolling was the earliest significant process computer application in the metallurgical industry. Computer control of rolling mill operations is now a steel mill standard component, particularly in plants newly placed into production. 1, 2 Initial computer installations principally carried out procedural routines in setting mill clearances for production lot control. Recent developments are leading toward feedback control based on mathematical model techniques. 3

Jan 1, 1969

By Kefton H. Teague

Olivine is a mineral containing a mixture of forsterite (Mg,SiO,) and fayalite (Fe,SiO,) in solid solution. The name "olivine" was first applied by Werner in 1790 (Hunter, 1941) because of the olive-green color of the mineral. Uses The principal use of olivine is in various foundry applications. Perhaps the largest tonnage is utilized as a special foundry sand for mold-making in brass, aluminum, and magnesium foundries (Schaller, 1957, 1958; Snyder, 1957). Olivine was first used as an industrial mineral in the early 1930s for a refractory material (Anon., 1970; Hunter, 1941). As a refractory raw material, olivine was first introduced in the United States as handcobbed, selected, shaped blocks of crude olivine. This use met with limited success. More recently, finely ground olivine blended with MgO and pressed into bricks, which are then fired, have found use in glass tank furnaces and open-hearth furnaces. Ramming or gunning mixes for basic furnace linings also utilize olivine. Olivine has been used in ladle linings with varied success. In Europe, substantial tonnages of olivine are utilized in refractory brick for night storage heaters (Anon., 1970). A limited amount of olivine has been used in the past as a fertilizer (magnesium source) and has been fused with rock phosphate to produce a magnesium phosphate as a plant food. The relatively high magnesia (MgO) content of olivine also attracted attention to it as a potential source of both magnesium compounds and as a source of metallic magnesium (Bengston, 1956; Hunter, 1941). Industries using olivine have not standardized specifications. Normally, producers supply a product which meets individual customer requirements. Such requirements involve type and amount of impurities, grain size of product, refractory characteristics, etc. Geology Olivine occurs commonly as accessories in basic igneous and basic metamorphic rocks. Economic deposits are of magmatic origin and are restricted to essentially the dunite variety of periodotite. Dunites are medium to coarse- grained crystalline rocks, generally reddish brown on weathered outcrop, and are composed primarily of olivine.

Jan 1, 1975

By W. T. Thom

Many able men have contributed to the subject of coal classification, and recent publications on the subject have indicated a crystallization of opinion in that connection which promises the development in the near future of a scheme of coal classification which will be of real and increasing value to coal producers and users, as well as to those interested in coal on more exclusively scientific grounds. It is obvious that such a classification must be simple; must be based upon readily ascertainable factors; and if properly developed will apply to the whole range of coals between peat and anthracite and not merely to certain types of coal. Many of the numerous schemes of classification proposed in the past have given quite satisfactory results when applied to the higher rank coals, but have broken down when applied to the younger coals of higher moisture, and, as previously pointed out by the writer,' this breakdown has been due to the practice of ruling out "moisture" as an essential component of the volatile matter reported in the customary proximate analysis of coal, whereas a review of the mode of formation and natural history of coal satisfies us that moisture is a normal and natural ingredient among its volatile constituents; and a knowledge of analytical practice shows that the "moisture" and "volatile matter" reported are both mixtures of moisture and volatile matter, rather than sharply differentiated distillation fractions. After an extended consideration of the subject the writer regards the conventional proximate analyses of coals as affording the information essential for a both practically and scientifically satisfactory c1assification—assuming that the coal samples compared have been collected and analyzed according to standard methods. Two variables are required for a workable classification, and these appear to be afforded by the calorific value and proportion of volatile constituents (including moisture) credited to the coal on an ash-free basis. The writer originally proposed that the figures used for classification purposes be those given for the "air-dried" and "ash-free" form of the proximate analysis,

Jan 1, 1930

By Robert H. Richards

Walter Renton Ingalls recently gave a very interesting talk before the student mining society of the Massachusetts Institute of Technology. In it he showed the present status of mining as he sees it. In the talk he explained that, while discoveries of great mining districts are still pssible, they are being made less and less often; that the great mining companies, although there are large numbers of mines offered for sale, are finding it less and less possible to find new mines that are up to the standard of richness that they wish for purchase. The natural conclusion is that better, cheaper, and more efficient methods of mining, concentrating, and smelting are needed if the lower-grade mines are to be worked at a profit. This is true also if the high-grade mines are to yield their greatest profit. This paper deals only with the concentrating or ore-dressing problem, and gives some thoughts which point towards greater profit. In a paper on The Development of Hindered-Settling Apparatus the writer showed that there were two main lines of work that would lead to greater saving, lower tailing assay, and, therefore, greater profit. The first is the recrushing of middling or tailing products for the saving of the contained values. This is well understood and largely carried out in existing mills. The second is the saving of fine free mineral at the first opportunity. This is a matter less well understood in the mills, and to dwell upon this the present paper is written. The writer is himself convinced and hopes to convince the reader that, for obtaining the above result, not only is better classification needed, but also more classification; that is, there should be more spigots or pockets to the classifier. His attention was recently called to a small mill which had a three-pocket cone classifier fed with from 2 to 0 mm. stuff, supplying feed to four Wilfley tables. The first spigot had about all the

Jan 1, 1914

By James Quigley

As the outcrop mines in the West developed into underground operations, systems of ground sup- port were gradually evolved. In the early coal mines there was little need for support except near the dirt line in portals, where stone masonry was common. Where the top was shaley or broken, native pine props with light cross bars and legs furnished enough support even in Utah's 25-ft coal seams. As depth of workings increased, roofs and backs of the same general nature as those near the surface became more and more unstable and required more and more support. Some coal airways show this tendency very clearly. From the surface down the same type of roof shows deterioration which an experienced eye can translate into a measure of depth under surface rather than change in rock characteristics. Rock bolts, developed by various companies and by the U. S. Bureau of Mines, have become an effective substitute for timber in sections of some metal and nonmetal mines formerly requiring excessive timber support, and further use of war surplus landing mats, chain link fencing, and a new punched channel developed by one of the steel companies has enabled other mines to operate deposits where costs of timber and lack of clearance for timber support would have prohibited mining. The block caving mines have made extensive use of reinforced concrete underground to achieve similar ends under difficult conditions. Steel sets are standard in many Bureau of Reclamation projects, although these are usually covered in with concrete to make the permanent structures the Bureau's reclamation projects require. But the use of steel in mining operations is limited and has been confined principally to the iron ore mines of Michigan, Wisconsin, and Minnesota. Some mines have installed used rail as posts, caps, and crossbars, but a rail section is not suited for load carrying, and used rails are generally brittle, having a tendency to fail without warning when overloaded.

Jan 7, 1959

By John H. Hollomon

The interpretation of notched-bar impact results has been a matter of controversy since the introduction of more or less standard tests by Fremont,' Charpy2 and others at the turn of the century. Many investigators3-l1 have contributed to the understanding of the significance of such tests. Several symposiums12,13 have been held with the express purpose of discussing the significance and interpretation of the impact tests. It is not the purpose of this paper to review all these contributions to the development of the knowledge on this subject, but rather to present an interpretation of notched-bar impact tests that appears to be in agreement with the available published data. Fundamentally, the interpretation discussed in this paper of the brittle failure of some steels in notched-bar impact test is similar to the qualitative analysis presented by Ludwik3 in the I92o's. Essentially, Ludwik stated that the function of the notch was to increase the tensile stress necessary for yielding, and that brittle failure occurred when the stress necessary for yielding exceeded the normal stress required for fracture (with no plastic deformation). Ludwik, however, had no means of measuring this normal stress necessary for failure of a plastically* undeformed metal, therefore he could not extend his interpretation beyond the qualitative stage. Kuntze14 and recently Mc-Adam15 attempted to determine the effect of deformation on the stress necessary for fracture by testing, in tension, specimens notched to various depths and angles. Because of the uncertainties in Kuntze's (and McAdam's) analysis of the stresses (which have been pointed out by Sachs16) and the inherent nonuniformity in the stress distribution in notched bars, the results of such investigations are difficult to interpret. A more direct method of measuring the effect of deformation on the fracture stress was suggested in previous papers"-18 and has been utilized in the present investigation. The present paper concerns itself primarily with the behavior of notched impact specimens. The effects of strain rate, temperature, and stress distribution, which are discussed with reference to the impact specimen, apply just as well to the behavior of metal at the bases of notches in any engineering structure. All that is necessary is to determine the stress distribution in the structure at the base of the notches.

Jan 1, 1944

By John H. Hollomon

The interpretation of notched-bar impact results has been a matter of controversy since the introduction of more or less standard tests by Fremont,' Charpy2 and others at the turn of the century. Many investigators3-l1 have contributed to the understanding of the significance of such tests. Several symposiums12,13 have been held with the express purpose of discussing the significance and interpretation of the impact tests. It is not the purpose of this paper to review all these contributions to the development of the knowledge on this subject, but rather to present an interpretation of notched-bar impact tests that appears to be in agreement with the available published data. Fundamentally, the interpretation discussed in this paper of the brittle failure of some steels in notched-bar impact test is similar to the qualitative analysis presented by Ludwik3 in the I92o's. Essentially, Ludwik stated that the function of the notch was to increase the tensile stress necessary for yielding, and that brittle failure occurred when the stress necessary for yielding exceeded the normal stress required for fracture (with no plastic deformation). Ludwik, however, had no means of measuring this normal stress necessary for failure of a plastically* undeformed metal, therefore he could not extend his interpretation beyond the qualitative stage. Kuntze14 and recently Mc-Adam15 attempted to determine the effect of deformation on the stress necessary for fracture by testing, in tension, specimens notched to various depths and angles. Because of the uncertainties in Kuntze's (and McAdam's) analysis of the stresses (which have been pointed out by Sachs16) and the inherent nonuniformity in the stress distribution in notched bars, the results of such investigations are difficult to interpret. A more direct method of measuring the effect of deformation on the fracture stress was suggested in previous papers"-18 and has been utilized in the present investigation. The present paper concerns itself primarily with the behavior of notched impact specimens. The effects of strain rate, temperature, and stress distribution, which are discussed with reference to the impact specimen, apply just as well to the behavior of metal at the bases of notches in any engineering structure. All that is necessary is to determine the stress distribution in the structure at the base of the notches.

Jan 1, 1944

By W. W. Mullins, F. A. Nichols

Solutions are developed, assuming surface diffusion and both internal and external volume diffusion, for the relaxation of bodies slightly perturbed from spherical and cylindrical geometries. Combined with those previously published for the nearly planar case, these results provide a means of gaging the relative contributions of the two diffusional proc-cesses in any given case. It is shown that in all sintering experiments to date, and probably in any attainable in practice, surface diffusion has played the dominant role, although most previous authors have assumed otherwise. It is also shown that surface diffusion predominates in normal field-emission tip blunting and also for the coalescence of gas bubbles introduced into metals by a bombardment. The surface-diffusion solutions for a perturbed sphere are combined with previous results for volume diffusion to show that the inclusion of interface diffusion permits considerably larger spheres to develop in diffusion-controlled precipitate growth before the onset of instability. A mechanism is also proposed for the spheroidization of precipitate platelets as well as rods. In a previous paper1 the relaxation of a nearly plane surface to flatness by the combined action of the transport processes of viscous flow, evaporation-condensation (in a closed system), volume diffusion, and surface diffusion has been analyzed under the assumption that all surface properties are independent of orientation. In this treatment, criteria were developed for deciding which process predominates, and solutions valid in the latter stages of the sintering of small wires and particles to a plane were obtained. A numerical solution, valid throughout the entire particle-sintering process for the case of surface diffusion, was subsequently obtained by the present authors.' It was found that the analytic solution (which assumed small slopes everywhere) is accurate to within -10 pct when the maximum slope of the profile is less than 0.3; the wire-sintering problem has also been solved nu- merically for the case of surface diffusion and here again the results converge to the analytic small-slope solution at late stages of the process, the two solutions agreeing in this case to within 10 pct when the maximum slope of the profile is less than -0.6. The purpose of this paper is to extend the perturbation solutions to nearly spherical and nearly cylindrical geometries. We treat only the two principal diffusional processes, i.e., surface and volume, but for these geometries we discuss volume diffusion both inside and outside of the solid. Our results, when coupled with Mullins' solutions1 for nearly planar surfaces, provide criteria for gaging the relative contributions of surface and volume diffusion to the over-all transport process in three basic geometries. A very interesting feature in the cylindrical case is the occurrence of instability for longitudinal perturbations with wavelengths greater than the cylindrical circumference, a classical result. This instability of the cylindrical surface is applied to give a quantitative explanation for the often-observed "erratic" pore closure in the late stages of the sintering of wire compacts; also, the theory previously presented for the spheroidization of rod-shaped precipitates by surface (interface) diffusion' is expanded now to include volume diffusion inside and outside of the particle. The results for circumferential perturbations on a long cylinder allow quantitative estimates for gaging the relative importance of surface or volume diffusion in the early stages of the sintering of spheres or wires. The results here demonstrate clearly that surface diffusion has played a very important, if not dominant, role in all sintering experiments discussed in the literature, although the surface-diffusion contribution to the kinetics has usually been ignored. The results for the sphere (surface-diffusion case) are added to the results obtained previously by Mullins and sekerka3 concerning instabilities of a growing spherical precipitate particle (with interface diffusion disallowed) to obtain a general solution to this problem including interface diffusion. The inclusion of interface diffusion is found to increase significantly the range of stability of a growing spherical precipitate for typical metallurgical cases. The following assumptions are made: (i) the initial surface lies everywhere near and has a slope differing only slightly from that of the reference

Jan 1, 1965

By H. Van F. Furman

TO those engaged in the purchase and sale of gold- and silverores, mattes and bullion, the frequent differences in the gold- and silver-contents, as reported by different assayers, is a source of much annoyance and expense. The desirability of uniform methods of assay has long been recognized by certain refiners who specify in their bullion-contracts the method to be adopted in assaying the bullion. One large producer of base bullion employs at each refining-works with whom it has a bullion contract an assayer whose duty it is to see that the bullion is sampled and assayed according to contract-specifications. For the assay of gold- and silver-bullion, standard methods are now generally adopted; the reeult being that differences seldom occur. While we cannot hope for anything near perfection from fireassay methods for ores, mattes and base bullion, as carried out cornmercially, such methods may be made to yield results which answer all commercial requirements, and they will probably be retained for obvious reasons. The object of the present paper is to point out some of the sources of error and to show the importance of more uniform methods of assay and close attention to the details of the work. The sources of error in the assay of ores and mattes are: improper sampling; losses of the precious metals during fusion, scorification and cupellation; imperfect elimination of the base metals on the cupel and imperfect extraction of the silver during the parting in nitric acid. It is not the object of the present paper to enter upon the subject of sampling; but a few remarks may be of value. There has been considerable discussion recently in Colorado upon the frequent differences which occur in the assays of Cripple Creek gold-ores, and these differences have been attributed to various causes. The writer is informed by two of our most prominent smelters that since they have adopted 100-mesh screens (the general practice is 80-mesh) the

Jan 1, 1895

By C. K. Ferguson, J. A. Klotz

This paper describes experimental investigations conducted at the California Research Corporation's model oil well. The first part describes filter loss from several drilling muds through bore hole walls during mud circulation and drill string rotation. The effect of mud properties and drill string rotation with mud circulation is described. Filtration from a bore hole full of drilling mud, not circulating, but under pressure for extended time periods, is also discussed. The second part describes filter loss to permeable formations from beneath a drilling bit where filter cuke has no opportunity to develop appreciable thickness. If potential flow theory is applied to predict filtrate invasion from this hole bottom, targe invasions arc calculated. But model well experimentation shows that filtrate invasion from the hole bottom is controlled by mud particles that penetrate the formation ahead of the bit. This experimentation provides data to estimate the effect of mud particle penetration on fluid loss to formation. The third part presents an estimate of mud filtration during drilling of a well. INTRODUCTION As oil wells are drilled by the rotary method, drilling mud circulates up the annulus between drill pine and well wall. Drillers adjust mud density so that the pressure at the bottom of the mud column is several hundred psi greater than the pressure of reservoir fluid. As a result of this pressure difference, the liquid part of the mud filters into the rock around the bore and mud solids deposit as a filter cake on the well wall. For many reasons the petrogleum industry, within the past 20 years, has spent much money and energy to determine the volume of mud filtrate that enters rock around the well bore and dedicated much research effort to reduce this volume. Among the reasons for attempts to determine the volume of mud filtrate and to reduce this volume are the following: 1. If filtrate damages the permeability of oil sand, the resultant damage to oil well productivity will depend on the distance that the filtrate invades the oil sand; reduction of filtrate volume may, therefore, increase well productivity. 2. Filtrate that penetrates shale sections may cause the shale to swell and to slough into the well bore. Uncontrolled sloughing may stick drill pipe. Reduction in filtrate volume may reduce drilling trouble. 3. Electric log resistivity curves are changed by invasion of a mud filtrate; the change depends on the depth to which filtrate invades. Knowledge of this depth is necessary before resistivity logs can be interpreted accurately. For these reasons, specifications the place an upper limit to drilling mud filter loss are now written into almost all drilling programs. These specifications are based on APT Recommended practice 29, Standard Field Procedure for Testing Drilling Fluids,' which describes a static filtration test operated at 100 psi filtration pressure and at ambient temperature. Although this test is adequate for mud control, it cannot be used to compare filtration properties of different muds. Schremp and Johnson' showed, for example, that mud with a low API filter loss does not necessarily have low filter loss at bottom hole temperature and pressure. Also, no information has been available about the effect of bottom hole mechanics (mild circulation, drill string rotation, and bit action) on mud filtration. This paper discusses filtration data measured in the California Research Corporation's model oil well, which models closely oil well bottom hole geometry and hydrodynamic conditions. The filtration processes that

Jan 1, 1955

By Danforth R. Hale, R. E. Blair

Minerals for electronic and optical uses divide easily into two sections: (1) quartz and (2) minerals other than quartz. Quartz Quartz, having a great usefulness discovered by the radio communication enthusiasts about 1918, has become a subject of amazingly expanded interest in the US over the past decade as a man-made mineral and a multimillion dollar crystal-growing business. An economic summary of the commercial growing of quartz crystals has a place in a handbook directed to the mineral engineering industry when it is remembered that quartz crystals have long been an important commercial mineral, and that the raw material for "cultured quartz"-that is to say, quartz crystals grown through the ingenuity of man-is still natural quartz. Nearly all the natural crystals come from Brazil. The larger pieces which meet rigorous standards of quality are used for electronic and, to a lesser extent, optical components. Smaller pieces and fragments are used for vitreous silica. The need for high quality material in quantity led to US government-sponsored research programs in the 1940s that have resulted in the factory growing of beautiful crystals of prescribed shape, size, and quality. The development of the cultured quartz crystal is typical of man's success in adapting the product of the mine to increasingly sophisticated uses. A remarkable achievement perhaps, but foreshadowed by experiments in 1908 by Giorgio Spezia (1908), an Italian geologist studying the relative effects of temperature and alkaline environment on the solubility of quartz. Modern radio equipment is most often controlled as to frequency by the presence in the circuit of a separately added "crystal"-the 1918 discovery responsible for the existence and growth of the quartz industry. The "crystal" is quartz, but this component is a carefully oriented and prepared slice from a crystal, but not a crystal as recognized by a rock hound or seen in a museum. How quartz operates to control frequencies is not a proper subject for a handbook on industrial minerals, and references should be consulted (Cady, 1964; Mason, 1964). Quartz belongs to that class of materials called dielectrics: those that do not conduct an electric current but permit electric fields to exist and act across them. Quartz shows the "piezoelectric effect," which means that when a quartz plate is mechanically deformed against its natural stiffness, one of its surfaces becomes negatively charged, the other, positively charged. When the plate is released from the stress quickly, the charges disappear as the plate regains its original shape, but because of mechanical momentum the plate deforms in the opposite direction (to a lesser amount) and the surfaces correspondingly become charged in the opposite direction. By coating the two surfaces thinly with metal and attaching flexible wires, these charges may be brought into an electronic circuit. If the surfaces are suddenly electrically charged by movement of current through the wires, the "converse piezoelectric effect" occurs -the plate deforms. Carry the thought further and it is realized that an alternating current flowing through the wires responds to the mechanical oscillation of the plate and is keyed to this oscillation. By controlling the thickness of the plate its mechanical vibration frequency can be varied through a wide range. One type of quartz plate, called the AT-cut, having a precisely defined orientation with respect to the crystallographic axes of the crystal, vibrates on a microscopic scale much as a book would deform when placed flat on a table and the top cover moved parallel back and forth with the hand. There are at least 17 other orientations which have been studied, some of

Jan 1, 1983

By John A. Garcia

A standard set of coal mining laws for the entire United States is hardly practicsble, yet the numerous variations in the state laws for almost every item seems entirely unnecessary. The same useless variations appear in almost every comparable section with no apparent reason except that no attempt has ever been made to codify them, and as they were developed over a long period of time by innumerable individuals and legislatures, the present situation is the logical outcome of lack of cooperation between states. The ventilation of a mine is affected indirectly by many provisions not listed specifically under this heading, so that it would be necessary to tabulate the major portion of all the laws to secure a complete comparable digest; therefore only a few of the more important have been set down here. This point is well illustrated in the section providing for clearance between car and rib, which is intended as a safety measure against personal injury, but is very important from the standpoint of ventilation because of choked airways in mines on two-entry system. Confusing Phraseology Misinterpretation and confusion may be expected from the phraseology alone; one state provides that the scale of the mine map shall be "not more than 100 ft. to 1 in.;'' another state demands "not less than 100 ft. to 1 in." Both probably mean the same thing and seek to prevent the operator from furnishing a map on which the workings will appear SO small that the detail is illegible. Legislation is certainly indefinite that specifies structures must be fireproof when "near" a mine opening, and just what is a "dusty" or "gaseous" mine is open to argument in most of the states. The variation in spacing crosscuts and break-throughs and the limited number of men on a split seem entirely unnecessary, as the distance is not reduced in gaseous fields, excepting in Arkansas and Tennessee, which states produce a comparatively small amount of coal, and the number of men differs 100 per cent. and more for no apparent reason.

Jan 1, 1927

By F. D. Rosi

The slip and twinning behavior in extended titanium crystals were studied in some detail. The formation and appearance of coarse kink bands are discussed. Their crystallographic geometry was determined by X-ray analysis. A phenomenological interpretation of the complexities in kink band development is also presented. The critical resolved shear stress, coefficient of shear hardening, and plane of fracture were determined for several crystals extended at room temperature. THE slip and twinning elements observed in the room-temperature deformation of titanium were enumerated in a previous paper1 in which considerations were advanced regarding the nature and selection of these elements and their effect on the known mechanical properties of this metal. The present study concerns the crystallographic, microscopic, and mechanical aspects of flow in relation to the slip and twinning elements, and includes a prediction of slip systems, nature of slip and twin markings, inhomogeneities of plastic flow, and stress-strain characteristics. Unless otherwise noted, arc-melted titanium sponge (99.77 pct) was used in these experiments. The method of production of crystals, their dimensions, and the surface preparation for micrographic examination have been reported.&apos; For obtaining stress-strain characteristics, only those crystals which traversed the entire width of the specimen and were at least 8 mm in length were used. Tensile deformation of the crystals was performed with conventional grips for sheet specimens and a constant-stress loading beam, designed after the method of Andrade and Chalmers.&apos; The specimens were loaded by allowing sand to flow from a reservoir into a bucket suspended from the longer end of a balanced 6:1 lever arm at a rate controlled to load the specimen approximately 2 kg per min. Strain measurements were made using the Baldwin SR-4, bonded, resistance-wire strain gage, Type A-8, which permitted a reading accuracy of 2 microinches per inch. The formulas used in the evaluation of shear stress and shear strain, as in deriving the coefficient of shear hardening, are given by Schmid and Boasv n terms of the original orientation and change in length of the crystal. For calculating the critical resolved shear stress, the standard equation was used. The crystallographic nature of the unpredictable slip observed in a number of specimens was determined by the single-surface X-ray method of analysis as described in ref. 1. Experimental Results Prediction of Slip System: It was reported&apos; that room temperature slip in titanium takes place predominantly on {10i0} and in a <1120> direction, giving three potential slip systems. Hence, it should be possible to predict the operative primary system in the manner used by Taylor and Elam&apos; for alu- minum (i.e., the one with the greatest component of shear stress in the direction of slip). The stereo-graphic construction in Fig. 1 shows that this is true. In all cases, slip was found to occur initially on the (0110) plane and, in a number of cases, in the [21f0] direction. (The direction of slip was not determined for all orientations.) It follows that duplex slip can be expected when two slip systems are geometrically equally favorable for slip, as demonstrated in Fig. 2. In both crystals slip took place simultaneously on the (1700) and (olio) prismatic planes, as indicated by Fig. 2a and b. In the case of crystal B the movement of the specimen axis with increasing extension was toward the (10i0) direction, which represents the stable end orientation resulting from alternate slip on the [2ii0] and [1120] directions. This is analogous to the duplex slip process in face-centered cubic metals." Unpredictable Slip: In a number of crystals whose orientations were well within the operation of a single slip system, secondary slip occurred on planes not predicted by the criterion of maximum shear stress. Examples are shown in Fig. 3. In addition to

Jan 1, 1955

By B. Ball, D. W. Fuerstenau, P. C. Kapur

A two-phase distributed-parameter model of the flotation process has been extended to allow consideration of the important process parameter, concentrate grade. A simple expression is presented for the grade of concentrate in terms of the zeroth and first moments of the concentrate distribution. An example is given for a binary ore containing two pure minerals each having nondistributed rate constants. For extend-ing the model to the distributed rate constant case, a cubic polynomial zoas utilized to simulate the feed distribution. One particular example is considered and grade-recovery curves are generated to show the dependence of such curves on the initial feed distribution. Operating flotation plant engineers have traditionally evaluated plant performance in terms of the recovery of valuable mineral and the grade of the concentrate. In both operation and research, grade-recovery relationships have been used as a guide for selecting flotation conditions. Weissl illustrated the use of grade-recovery curves in plant operation and considered the grade-recovery relationship to be a metallurgical one. The extensive experimental work of Chi" using standard batch flotation tests on iron ores shows that, even with extensive statistical correlation of data, little insight can be gained into the basic fundamentals of these relations. Such relations must depend on the kinetic behavior of the various mineral species in the flotation circuit. In his flotation text book, Gaudin3 considered the relationship of recovery and of product grade to flotation kinetic indices, but he did not extend his calculations to yield grade-recovery relations. Although Gaudin used a simplistic model for his analysis, he did recognize that variations in flotation rates must result from variations in locking, surface heterogeneity, particle size and shape, among other things. In a recent paper,&apos; we presented a model of the flotation process that could be readily analyzed with an analog computer. This model combines the concept of a distributed set of rate constants"" with that of the two-phase flotation model,8" resulting in a model more powerful and flexible than previous ones. The purpose of the present paper is to show how this model can be used to generate grade-recovery curves and to determine the dependence of such curves on the various kinetic parameters. In this paper, the model will be limited to the semi-batch case, but extension to the continuous case is a straightforward step.

Jan 1, 1971