Search Documents

By R. Adair, W. R. Hudspeth, W. T. McDaniel

ANEW method for concentrating the flake mica either from present washing plant tailings or from new feed has been developed. In this paper, flake mica refers to that which occurs in weathered granites, alaskites, pegmatites, and schists in a form too fine to be considered sheet mica. It ranges in size from 1 in. or more down to 200-mesh or finer and occurs with kaolin, quartz, and partially kaolinized feldspar. Scrap mica, a term often used indiscriminately to describe everything other than sheet mica, will be used to denote the waste product from sheet mica mines and fabricating plants. Both flake and scrap mica are used in the mica grinding plants to produce wet-ground or dry-ground mica, although some flake mica recovered from clay mining operations is fine enough to be marketed without grinding. Until 1930, ground mica was made almost entirely from scrap. From 1930 until 1935 a gradually increasing amount of flake mica was mined, and most of this was sold without grinding. A large percentage of this mica was recovered from clay washing plants. In this type of operation the recovery of any sheet mica was .of secondary importance and was considered a byproduct. North Carolina produces more flake mica than any other state, accounting for 73 pct of the total domestic production.' In the following review of current practice in jig plants, there is no intention to disparage these operations. Within the limitations under which they were built, they are examples of mechanical ingenuity. The term jig plant is a carryover from early practice since there are no jigs in operation at the present time. Current practice, as shown in Fig. 1, is based on successive stages of differential crushing with rolls followed by trommel screens to remove the more easily crushed gangue minerals. The oversize mica product then is usually dried, and passed through another set of dry rolls and a final screen to remove the remainder of the grit. This process is effective in recovering up to 50 pct of the mica in the original ore, the balance being lost in the screen undersize, usually —% in. Jigs and tables were at one time used to treat this screen undersize and were capable of recovering a part of the mica larger than about 60-mesh.V ine mica lost in these plants is normally washed away in streams and can be considered irrecoverable. There are ten or more washing plants in the North Carolina area that are losing approximately 50 pct of the mica in the feed. Since the three cooperating agencies, the Asheville Minerals Research Laboratory of North Carolina State College, the North Carolina Dept. of Conservation and Development, and the Tennessee Valley Authority, are concerned with conservation of minerals, they have investigated means for improving the efficiency of these mica plants. The mica industry has been cooperating fully with the laboratory to establish a more efficient method of recovery for flake mica. Choice of Methods The initial investigation was concentrated on finding a means of reducing the losses from plants now using the conventional flowsheet shown in Fig. 1. To accomplish this it would be necessary to collect the screen undersize products through the plant and remove from them the mica from Vs in. down to

Jan 1, 1952

By Chas. A. Ashburnea

THE appliances which have been proposed, and the modifications in the construction of boiler-furnaces which have been made for the prevention of smoke, and the utilization of what are ordinarily called the waste products of combustion, have been innumerable.† †There is now open in London an exhibition "of apparatus of all kinds devised to prevent smoke."

Jan 1, 1882

By A. H. Underwood, M. –Ls. Trépanier

INTRODUCTION The King and Beaver mines of Asbestos Corporation Limited (ACL) were joined in 1957 to form the King-Beaver mine. In 1964, ACL purchased the Johnson's Asbestos Company. The combined underground workings are a part of the King- Beaver mine. Asbestos ore is mined at the rate of 4080 metric tons per day (mtpd) to provide 15% of the company's daily requirement in the Thetford Mines area. Figure 1 shows the location of Thetford Mines. Two shafts service the underground. No. 3 shaft, 457 m deep, is used for personnel and material transportation, downcast ventilation, and ore hoisting. No. 4 shaft, 820 m to the south, is 389 m deep. It is used for material transportation and upcast ventilation. Figure 2 shows the relative locations of the shafts and the underground workings. The ore is mined by block caving. HISTORY The orebody outcropped at surface and was first mined as an open pit. Underground mining commenced when open pit mining became impractical. Shrinkage stoping, used initially, was unsatisfactory in the highly fractured ore. Sublevel stoping improved ore recovery and safety, but did not overcome the adverse effects of the un- stable rock. Observations of the rock failures indicated that block caving would be satisfactory. This was confirmed by careful investigation and testing. A method of block caving similar to that used at the Miami Copper Company was adopted. The first block commenced production in June 1933. BLOCK CAVING General A large block of ore is undercut above pre- pared drawpoints. The ore above the undercut caves by its own weight. Caving progresses up- ward as the caved ore is drawn. A large proportion of the rock breaks up in the caving action so that it will pass through the drawpoints. Oversize blocks are broken by drilling and blasting or mudcapping. Figure 3 shows the progressive stages of block caving. In the central part of the ore zone, the vertical dimension of a block is determined by the 132 metres between production levels. When isolated ore pockets are developed, the vertical dimensions of a block depend on the extension of the ore zone above the undercut. The minimum horizontal dimension of an under- cut determines the cavability of the overlying block. When necessary, caving is assisted by drilling long horizontal holes into the block above the undercut and blasting them. This procedure speeds up or restarts caving. It will not ensure complete caving of blocks having undercuts less than 30 m wide. Orebodies suitable for block caving are highly fractured and wide enough to cave freely without excessive dilution. Undercutting must

Jan 1, 1981

By LeRoy Scharon, P. Uhley

TEST gravity surveys were made in the Washington County barite district of Missouri on properly owned by the Baroid Sales Division of the National Lead Co. This property is located just northeast of Richwoods in the northeastern corner of Washington County, Fig. 1. The area to which the surveys were confined comprised approximately 5000 acres, of which some 525 acres were surveyed gravitationally. Gravity observations were made at 2600 points within the area, observations being confined to relatively clear and gently sloping ground. Part of the area was heavily wooded, and the terrain too rugged for either the occurrence of a commercial barite deposit or a feasible gravity survey. The relief along the central drainage, Ditch Creek, was about 140 ft, the maximum difference in elevation being 400 ft in a distance of 3½ miles. The purpose of the test gravity survey was to determine whether the gravity method of geophysical prospecting might be applied in the exploration for barite deposits in the Washington County barite district, since a satisfactory systematic procedure had not been devised to explore and ultimately determine barite ore reserves with desired accuracy. No previous geophysical work with respect to barite is known to have been done in this area. Stratigraphy: The formations over which the barite deposits occur' are Paleozoic in age, representing rocks involving sandstones and dolomites unconformably underlain by pre-Cambrain granites and rhyolite porphyries. The areas covered by the granite survey were directly underlain by almost

Jan 1, 1955

By F. J. Haller

The need for permanent, fireproof support indicated structural steel sets. Experience over the past six years, involving more than five miles of permanent underground openings, has proved that steel is permanent, safer and, in the long run, cheaper than either treated or untreated wood supports. Excavation is reduced, as are installation, transportation, and handling costs. A number of hazards are reduced or eliminated by the use of steel.

Jan 4, 1950

By J. H. Nelson

An outline survey of the economic outlook for the United States export trade in petroleum products resolves itself broadly into two general divisions; first, a consideration of our present position in this trade, and second, a discussion of the visible factors which promise to affect appreciable changes in the immediate future in that trade. The United States PetRoleum Exports of majoR Petroleum Products 1925, 1926 and 1927

Jan 1, 1928

E. T. DUMBLE, Houston, Tex.-This paper is a continuation of one that was published by Mr. Garfias, I believe, in the Journal of Geology, 1912, in which he gave the results of his investigations in Mexico, showing that the basalt extrusions frequently did not come up as cones. but reached the surface as a small neck and then mushroomed out into a sill, penetrating the beds both in limestones and in shales. He has continued his investigations to show that as these basalt protrusions came up they forced the strata into a funnel shape at the top instead of throwing them out altogether. While this may be true concerning these particular beds, there are other places at which the basalt does appear clearly as cones and dories, and there the funnel structure does not exist. We know that the sills are there, because we find them in the wells. In one well that I know of. we found a 2-ft. sill of basalt at about 1600 ft. and oil below it at about 2100 ft.; others have gone through similar beds. We also know that there. are cones, because north of the Ranuco River one well struck basalt at about 800 ft. and continued in it for several hundred feet-did not pass through it at all. This paper of Mr. Garfias will give us considerable help in that oil field. W. E. WRATHER, Wichita Falls, Tex.-I would like to ask for information as to the temperatures of Mexican oils. I have heard a number of conflicting reports about the high temperatures of the water and oil, and the relationship between them.

Jan 1, 1918

By D. W. McGlashan, K. N. Mcleod

IN the use of free bubbles with precise temperature control and continuous pH measurement, the contact angle apparatus differs from all previous equipment. Experimental procedures differ sharply from the captive bubble method1,2 of introducing the gaseous phase in the three-phase system. When freed from the tube and captured by a solid surface, a bubble more closely conforms to the spherical ideal set up by the usual mathematical analysis of surface free energy or surface tensional relationships of the forces involved. The assembled equipment, Fig. 1, departs from the usual contact angle apparatus in providing: 1) water circulation for fixing temperature, 2) instruments to measure and record pH during testing, and 3) a system for producing and using free bubbles. The apparatus allows testing over a broad range of closely controlled conditions, and the use of free bubbles gives contact angles independent of operator manipulation, which was unavoidable in the older captive bubble method. A bubble released below the specimen rises through the liquid and contacts the mineral. If the mineral is gas-avid the bubble adheres, developing a finite contact angle. Reaction cells (1), 2x33/8x5 3/16 in. ID, are of pyrex glass 5 mm thick. To prevent optical distortion, the sides are optical flats and are planed parallel to within five wave lengths of light over the entire surface. Special cement is required to withstand chemical attack and thermal shock. The cell is placed in a thermal jacket (2) made of welded aluminum. A water seal for the optical ports is made by using O-rings tightened against the flats of the cell by fine-threaded and adjustable ports, Fig. 2. In-flow water is discharged downward from a manifold located near the bottom of the cell jacket. Water overflows the weirs at each end of the cell jacket, discharging from both sides to a collecting manifold (24). A hose (26) leads the overflow water to the thermal-conditioner well (4), which is recessed to accommodate a reaction cell and two beakers (150 ml). Both the thermal jacket and the thermal-conditioner well are insulated to minimize the effects of temperature differentials. Water, discharging from the thermal-conditioner well, returns to a thermostat bath and pump (3), from which it is pumped to the thermal jacket. The thermostat bath permits temperatures to be adjusted from 1" or 2°C to 80°C and will maintain the selected temperature within 0.2ºC. An electrode support (22) groups the four electrodes (8) so that they fit conveniently into the reaction cell, Fig. 2. This assembly holds the glass electrode, the calomel electrode, the temperature-

Jan 1, 1957

By R. F. Hollis, C. K. McArthur

PRIOR to the application of anion exchange, all recovery of uranium from acid leach liquors precipitated an impure product requiring further upgrading before it could be refined. The ion exchange process, on the other hand, provides excellent selectivity for extracting soluble uranium from leach liquors, so that high grade concentrates can be produced directly. The discovery that uranium is readily adsorbed by anion exchange resins, together with the experience of resin and equipment manufacturers in water treatment, led to rapid development of ion exchange in a multiple column operation. Many processing plants using fixed bed ion exchange are in operation or under construction in Africa, Australia, and Canada. There are a limited number in the U. S. Although the fixed bed process has been highly successful, the feed to the ion exchange columns must be a clear solution, which is obtained by filtration or by countercurrent decantation of leached pulps. With some ores, poor filtration or settling characteristics make production of a clear solution difficult. Most processing plants in the U. S. receive their ores from a number of small mines, and there is considerable variation in the settling and filtering behavior of the ores. An ion exchange process was therefore desirable in which the uranium could be recovered directly for the leached pulp by adding ion exchange resin, which could be then separated from the pulp by a screening operation. The process would thus resemble the cyanide-charcoal process in which gold is adsorbed from cyanide pulp by means of activated charcoal. Preliminary tests in which leached pulps were directly contacted with resin beads led to the development of the RIP process.

Jan 4, 1957

By H. L. Sauder, J. L. Newman, C. Waddell

An instrument capable of measuring subsurface flow rates is described. The instrument is self-contained and may be run on piano wire line. It detects flow by means of an impeller suspended between two torsion wires. The force of the well fluid striking the impeller causes the impeller to rotate, exerting a torsional force to the wires. This force is determined by recording the angle of rotation of the impeller on film using a battery-driven, clock-controlled camera. The impeller is sensitive to flow in either direction and the same instrument can be used to measure injection as well as production rates. Changes in direction of flow, such as might be caused by thief zones, are measurable and are indicated by a reversal of the direction of rotation of the impeller. Adjustment of the sensitivity of the instrument to measure a wide range of flow rates is accomplished by the use of different size torsion wires. An umbrella-type fluid trap, which contacts the casing or wellbore, diverts the flow through the flow tube. The fluid trap remains closed while rurrning in the hole and can be opened at any point in the well. The instrument with the trap closed is 1 3/4 in. OD and may be run through 2 in. tubing. Successful flow profiles have been made on wells with flow rates ranging from 60 BID to 4,000 B/D at surface pressure up to 4,500 psi. The instrument is designed for high-pressure and high-temperature operations. INTRODUCTION The need for an instrument that will measure flow rates in a wellbore is as old as reservoir engineering itself. A number of such devices have been designed within the past few years. Some of these have been described in the literature1,2,3,4,5,6 One of these devices1. a hot-wire anemometer type, made many successful jobs in dry gas producing areas. Difficulty was encountered when this flowmeter was used in wells producing liquids and development work was initiated to overcome this difficulty. The present flowmeter is the result of this work and provides an instrument with a wider range of application in the industry. Consider- able development work has been done on the tool involving many changes in the mechanics of recording the flow readings, however, the basic principle of flow detection has remained the same since its inception. PRINCIPLE OF OPERATION The basic principle of operation of the flowmeter is the utilization of a portion of the kinetic energy of flowing well fluid to impart a rotational force to an impeller suspended between two torsion wires. This impeller, Fig. 1, is a screw-type propeller with the blades having a pitch angle of 40. As the well fluid passes through the instrument it strikes the impeller. The resulting force rotates the impeller and twist\ the torsion wires to a balance point at which the torque imparted to the wires balances the force required for the impeller to deflect the well fluid. The impeller is symmetrical and a change in direction of the flow results in a reversal of the direction in which the impeller is deflected. Thus the direction of the flow as well as its velocity is indicated. A dial is attached to the impeller by means of a hollow tube through which the upper torsion wire extends. The angular position of the impeller is recorded by photographing the dial at frequent intervals. In any given set of torsion wires the modulus of shear and polar moment of inertia remain constant and the deflection varies directly with the applied torque. The deflection imparted to the torsion wires also varies as the square of the fluid velocity. Further, the velocities represented by any two given deflections hear the following relationships: and Where V = velocity of flow stream and O ;= deflection. This is the basic relationship which is used to calculate the relative velocities represented by a given set of deflections where the velocity represented by any one of the deflection readings is a known quantity. For a given torque, the deflection of the torsion wire varies inversely as the fourth power of the wire diameter. Wire sizes ranging from ,005 in. in diameter to .022 in. in diameter can be used. The range of

Jan 1, 1957

By J. E. Worthington, W. H. Spence, I. T. Kiff

Gold was discovered at the Haile mine in Lancaster County, South Carolina, in 1827 or 1828, and since that time the mine has been worked intermittently by both open-pit and underground methods until its forced closure in 1942 by World War II. Production figures are incomplete, especially for the early years, but the total gold produced is estimated to have been greater than 200,000 oz. Thus, the Haile mine has been the most productive gold mine in the eastern United States. The upper, residually enriched ores were relatively rich, but the bulk of the production has come from the mining of lower grade ores. General Geology The Haile mine is located in late Precambrian or early Paleozoic rocks of the Carolina slate belt at the edge of the Atlantic Coastal Plain [(Fig. 1)]. The metamorphic grade is lower greenschist facies and the rocks have been folded into a sequence of northeast-trending isoclinal folds. The gold is associated with siliceous, pyritic, and kaolinized felsic pyroclastic and tuffaceous rocks in an interbedded volcanic and volcanoclastic sequence of felsic to mafic tuffaceous rocks and argillaceous sediments [(Fig. 2)]. The ore bodies occur in two northeast trending zones approximately 500 m apart; each zone is 30-70 m wide and 600 m or more in length, with possible extensions to the east beneath the Coastal Plain sediments. Mineralogy. Gold in the Haile mine is always associated with siliceous and/or pyritic ores. The gold occurs in at least three states: As native gold as originally deposited; as residual gold derived from the breakdown of pyrite; and as gold included in pyrite. Major associated minerals in addition to quartz and pyrite are kaolinite, sericite, and iron oxides. Minor molybdenite, arsenopyrite, pyrrhotite, copper sulfides, sphalerite, rutile, and topaz are also present. Petrology. The gold-bearing ore zones vary from highly siliceous rocks to pyritic massive sulfide lenses. This variation is most easily seen today along strike from the Haile pit to the Red Hill pit. Ore grade material still exposed in the wall of the Haile pit consists of a highly siliceous and very thinly bedded rock containing minor pyrite. Along strike, the character of the mineralization changes to pyritic massive sulfide lenses occurring interbedded with siliceous horizons at the Red Hill pit. The siliceous rocks vary from the thinly-bedded material as just described from the Haile pit to silicified fragmental-appearing rocks to totally recrystallized cherty rocks lacking any recognizable primary features. Scattered, apparently at random, throughout the very thinly-bedded and very fine-grained ore face of the Haile pit are seemingly anomalous silica-rich clasts or concretions up to 5 cm in diameter which will be discussed later in this paper. Alteration. One of the most striking features of the Haile deposit is the alteration mineral assemblage which is intimately associated with the siliceous and pyritic ores. This altered material has been intersected in drill core at depths greatly exceeding the modern weathering profile and is, therefore, of hydrothermal origin rather than from supergene processes. This "sericite," actually a fine-grained mixture of sericite, kaolinite, and quartz, can be shown to stratigraphically underlie the gold- quartz-pyrite zone, and is well exposed in the open pit just southeast of the Haile and Bumalo pits. Relict textures indicate that this highly altered material was originally a felsic ash flow. Other similar alteration zones have been found in outcrop and drill core underlying the remaining ore bodies. Thus each of the mineralized zones consists of two parts: A siliceous and/or pyritic gold-bearing ore zone which is stratigraphically underlain by a zone of high alumina minerals, in this case sericite and kaolinite along with variable amounts of quartz. A green chrome mica, presumably fuchsite, is present in trace amounts in the high alumina zone. Genesis An adequate model to explain the origin and distribution of the gold deposits in the Carolina slate belt is presently lacking. Worthington and Kiff1 suggested a volcanogenic origin for certain gold deposits in the North Carolina slate belt from the waning exhalations of felsic volcanic piles. They also pointed out that such an origin has similarities to many epithermal precious metal deposits located in more recent volcanic piles in the western United States. A further key to the understanding of the genesis of the gold mineralization at the Haile mine is the close association of the mineralization in siliceous and sulfidic horizons to the genetically related and stratigraphically underlying high alumina alteration. Such high-alumina alteration is common around felsic volcanic centers in the Carolina slate belt and the mineralogy as seen today consists of some combination of kaolinite, sericite, pyrophyllite, kyanite, andalusite or sillimanite depending on the local prevailing grade of metamorphism. Accompanying the high-alumina alteration are large quantities of pyrite and iron-oxide minerals as well as characteristic minor accessory minerals often including base metal sulfides, fluorine-bearing minerals (topaz, fluorite, apatite), titanium-bearing minerals (ilmenite, rutile),

Jan 1, 1981

By Terry G. Richard, Vernal H. Kenner, Sunder H. Advani

This paper presents and discusses the results of thirty-one fracture toughness tests on Pennsylvanian Age Clay Shale. Two different orientations for this anisotropic material were studied and two series of tests were conducted, namely, 1. a test series to determine the effect of moisture content on fracture toughness, and 2. a test series to study mixed mode fracture. Increased absorbed moisture is found to reduce fracture toughness. Several analyses of mixed mode failure are found to give varying non-conservative predictions of failure stress intensity level.

Jan 1, 1982

By P. E. Demmler

PHOSPHORUS combines with copper in various proportions, forming true alloys, some of which are of commercial importance. These materials find wide application as deoxidizers and as a means of introducing phosphorus into other alloys, as in phosphor-bronze. Phosphor-coppers containing 10 and 15 per cent. of phosphorus are the commercial grades that are most generally offered. Each has certain advantages when used in making other alloys. The 10 per cent. grade of phosphor-copper has an advantage over the 15 per cent. in that it has a much lower melting point and can be prepared by certain methods with a much lower loss in phosphorus. The 15 per cent. grade has the advantage of lower freight rates per unit of phosphorus and, by the method to be described, a uniform product can be prepared with practically no loss of phosphorus. Alloys of copper and phosphorus containing any desired percentage of phosphorus lower than 15 per cent. can be prepared by melting together the requisite amounts of copper and 15 per cent. phosphor-copper. Processes for making phosphor-copper may be divided into two classes as follows: (1) Those depending on the smelting of phosphate rock or superphosphate of calcium with copper or copper-bearing materials, and coal or other carbonaceous material; (2) those depending on the direct combination of metallic copper and elemental phosphorus. A number of formulas for preparing phosphor-copper according to the first method have been published. The Metal, Industry' gives-the following: Superphosphate of calcium, 60 lb.; granulated copper, 301b.; finely powdered coal, 10 lb. Similar formulas are given by Brannt2 and others, and detail 'variations are covered by patents, such as those of L A Jeffs3 and H A Webster.4

Jan 8, 1920

By F. Rosenblum

An on-stream particle size analyzer (PSA) based on the sedimentation principle has been developed to the commercial prototype stage and tested at a concentrator. The current instrument gives a direct reading of the weight % finer than any two sizes, although the capability exists for providing a complete size distribution through the sieve and sub-sieve range. The readings obtained at intervals of about 10 minutes are derived from 0.5-L samples of slurry cut from the monitored stream. The accuracy of the PSA meets the requirements of process control.

Jan 1, 1984

By Ove Rehnberg

Catalytic purifiers are widely used as exhaust treatment devices on diesel equipment in confined spaces. The paper summarizes some studies carried out at the University of Lulea on diesel exhaust purifiers. The main purpose has been to elucidate important chemical activities of catalysts useful for the improvement of their effect. The effects of platinum catalysts on exhaust constituents such as carbon monoxide, nitrogen oxides, unburned gaseous hydrocarbons, and polynuclear aromatic hydrocarbons are discussed. Also pointed out are the great differences in catalyst activity and advantages/disadvantages associated with the catalysts.

Jan 1, 1982

By F. G. Miller, J. M. Podgursky

Laboratory and pilot plant work on tabling of 14-mesh X 0 hydrocyclone under flow are summarized. Included are: operating principles of hydrocyclones and tables; performance of these two devices, separately as well as in combination; comparison of the combination hydrocyclone-table system with other fine-coal processing systems; and application of the hydrocyclone-table system in fine-coal circuits. The data show that the table actually compensates for the shortcomings of hydrocyclone and makes a combination table-hydrocyclone system attractive, particularly in those cases where fine pyrite is one of the major contaminants.

Jan 1, 1973

By G. W. Thomas

Jan 1, 1967

By J. P. Carson

The works of the Tula Iron Company are in the Republic of Mexico, State of Jalisco, twenty-eight leagues southwest of Guadalajara, ten leagues northwest of the town of Sayula, through which passes the projected line of the Mexican National Railroad. Its geographical position would be about: latitude, 20' 10' N., longitude, 40 35' w. of Mexico City. The surrounding country is a rolling plateau, 6000 feet above the sea, enjoying the most magnificent climate in the world, the average temperature being about '70'. The works were commenced in 1850 by a company with very small capital, having not the least idea of the undertaking. They soon fell into the hands of the money-lenders, and after changing

Jan 1, 1879

By Gerald Sherman

MINE fires are always dangerous and are frequently accompanied by loss of life during the period of confusion which is apt to follow their discovery. In metal mines, fires may result from the accidental ignition of some combustible material, or they may be of spontaneous origin resulting from the rapid decomposition of sulphide. They occur frequently enough to demonstrate the need of some special equipment and a general plan for controlling them, in addition to measures for their prevention. Nearly all the large copper mines have had fires, and the methods of fighting them have been well described in recent papers, notably-by C. L. Berrien,1 R.. E. Tally,2 and others in discussion. The Copper Queen mine has many shafts, which are connected by underground workings. The deeper parts are ventilated by fans, but in the shallower portions natural ventilation through numerous connecting raises or shafts is sufficient. There have been several fires in the past few years, of which all are extinguished but one, and that is under control. These notes cover particularly the preparations that are being made-to check a new fire, partially or temporarily, and to facilitate the escape of workmen in the interval before a definite plan of fighting it can be established. A fire may occur in a shaft or station, or in some working father away. In case of fire in an upcast shaft, the gas would escape to the surface and the immediate result would probably not be dangerous to workmen, as they could escape by other shafts. In a downcast shaft, however, the gas would be distributed very rapidly throughout a large portion of the mine, and men might easily be trapped and asphyxiated. A fire in mine workings, drift, raise, or stope, would be dangerous in a degree, but the draft there is likely to be less strong than in a shaft and probably a smaller area would be invaded by the fire gases.

Jan 1, 1918