Search Documents

By W. F. Dietrich

Mineral fillers are relatively inert chemically under the conditions of use but have physical properties* that modify those of the materials • The properties. uses, and other data on 15 classes of important *The pro listed in the second edition of Industrial Minerals and Rocks.l A third edition of this reference is in preparation. in which they are incorporated. The mineral fillers considered in this article are asbestos, barite, clays, diatomite, crushed limestone, limestone whiting and lime, mica, silica, talc and soapstone, and pyrophyllite. Slate and stone, other than limestone and its derivatives, are excluded because, even though used in large quantities, they are exceptionally low-cost materials generally produced close to the area where they are used. Carbon black is excluded because it is manufactured from natural gas and more than 90 pct of the output is used in rubber; hence the factors for estimating requirements are easily evaluated. OVERALL GROWTH FACTORS Table I gives the population, retail sales, and value added by manufactures in the U. S. and in the eleven western states in 1954. These data are rough guides to the proportionate part of total U. S. markets for products containing mineral fillers that may be expected in a given area. For example, the population of the eight Mountain states in 1954 was 3.6 pct, and retail sales in these states were 3.8 pct of the U. S. total, but the value added by manufactures was only 1.3 pct of the U. S. total. On the other hand, the three Pacific Coast states, with 10.3 pct of the total population, had 12.0 pct of the retail sales and produced 9.6 pct of the value added by manufactures. On an industry-by-industry basis the correlation between the three guideposts will not be as close as shown in the 1954 data for the Pacific Coast states, but in the long-term view the continuing rapid population growth in the western states is certain to result in expanded industrial production at an even more accelerated pace, which will shorten the gap between local consumption and production in most major groups of manufactured consumer goods. Of course, there will always remain favorable areas for production of specific products. Such special situations must be individually analyzed. Fig. 1 compares the population trends in the U. S., the western states, and California with Real Gross National Product from 1910 to 1957, with forecasts to 1970. It is estimated' that the U. S. Real Gross National Product, as measured by the value of goods and

Jan 1, 1960

By P.V. Roundy, G.R. Mansfield

Public lands in Florida were first withdrawn from entry by President Taft on July 2, 1910, as a conservation measure because of their possible phosphate content. The reserve thus established was subsequently modified by further withdrawals and by restorations, so that on Jan. 1, 1934, it contained 66,796 acres, of which only a small part had been definitely classified. The reserved land was in scattered parcels, ranging from less than 40 acres to 320 or more, distributed in many counties. For administrative purposes and for final disposal of any of the numerous parcels, mineral classification of the land is legally necessary. In 1934 and 1935 the United States Geological Survey, under two successive grants from the Public Works Administration, prospected some 83 tracts of these lands in Polk County, comprising in all about 3300 acres, and six tracts comprising 240 acres in Citrus and Marion Counties. The tracts in Polk County were all in the so-called land-pebble field and the others in the hard-rock field. The Survey field party was under the direction of P. V. Roundy, from whose unpublished report the material in this paper is largely taken. The foreman of the prospecting crew was J. H. Wingate of Zephyrhills, Fla. The individual tracts were identified through the cooperation of the General Land Office, by transitman Hugh B. Crawford. This prospecting work fitted well the classification adopted for Public Works projects in general: it could not be done on any considerable scale under the Survey's usual appropriations; it gave employment to unemployed labor; and it may be expected ultimately to repay the Government in royalties more than the cost of the exploration. Commercial, Prospecting Methods Commercial methods of prospeeting for phosphate in Florida have been briefly described by Mansfield.' In the hard-rock field, where the floor of the phosphate deposit is extremely irregular, it is customary to drill a.:

Jan 1, 1938

By P. V. Roundy, G. R. Mansfield

Public lands in Florida were first withdrawn from entry by President Taft on July 2, 1910, as a conservation measure because of their possible phosphate content. The reserve thus established was subsequently modified by further withdrawals and by restorations, so that on Jan. 1, 1934, it contained 66,796 acres, of which only a small part had been definitely classified. The reserved land was in scattered parcels, ranging from less than 40 acres to 320 or more, distributed in many counties. For administrative purposes and for final disposal of any of the numerous parcels, mineral classification of the land is legally necessary. In 1934 and 1935 the United States Geological Survey, under two successive grants from the Public Works Administration, prospected some 83 tracts of these lands in Polk County, comprising in all about 3300 acres, and six tracts comprising 240 acres in Citrus and Marion Counties. The tracts in Polk County were all in the so-called land-pebble field and the others in the hard-rock field. The Survey field party was under the direction of P. V. Roundy, from whose unpublished report the material in this paper is largely taken. The foreman of the prospecting crew was J. H. Wingate of Zephyrhills, Fla. The individual tracts were identified through the cooperation of the General Land Office, by transitman Hugh B. Crawford. This prospecting work fitted well the classification adopted for Public Works projects in general: it could not be done on any considerable scale under the Survey's usual appropriations; it gave employment to unemployed labor; and it may be expected ultimately to repay the Government in royalties more than the cost of the exploration. Commercial, Prospecting Methods Commercial methods of prospeeting for phosphate in Florida have been briefly described by Mansfield.' In the hard-rock field, where the floor of the phosphate deposit is extremely irregular, it is customary to drill a.:

Jan 1, 1938

By G. F. Swindle

This paper discusses a Personal Computer (PC) software package that reduces the time required to evaluate a mineral reserve. It provides for: •Entry of borehole data onto PC diskettes and the creation of a borehole database; •Capture of map data using an attached X-Y digitizer; •Calculation of uniform square grids for thickness, mineral qualities, overburden ratio, etc., •Compilation of multiple such grids into a digital model, and iterative evaluation of the model with the user applying constraints and cut-off values; and • Graphic display of grid cells (blocks) showing which cells failed, and on which constraint(s), and a complete reserve report showing tonnages, averages, histograms, and quality arrays.

Jan 1, 1985

By S. Norton

IN the West, capitalists have expended many millions of dollars developing the low-grade porphyry ores of copper. Half a dozen of these great enterprises have proved to be wonderful commercial successes. They have demanded improved crushing and concentrating machinery and consequently it has been .developed. Many improved methods, cheap power, superior business organization, all these have contributed to this success, but the main feature is the handling of the material in enormous quantities, on a manufacturing scale. The mining chance of "striking it rich" has been eliminated by the manufacturing certainty, of handling large quantities of material of known valise, which while of relatively low grade, is available in large tonnages, assuring a supply for .many years' run of the mill. Then the returns on the money invested are sure. The concentration of low-grade magnetic iron ores, separating the magnetite crystals from the gangue by the use of magnets, is a field of work in which the lessons taught by the development of the porphyry coppers can be studied to advantage. Large-scale operations, and the liberal expenditure of enough money at the start to insure the most economical operations, are the means of securing the desired results. The problem is to utilize millions of tons, and we may safely say billions of tons, of now worthless iron-bearing rock and to, produce from it 10,000,000 to 20,000,000 tons per year of high-grade ore carrying 60 per cent. iron or, higher;. to take the lean material as found in nature, varying widely in iron content, and bring it up to a uniform standard of shipping ore. At present these ores are mined carrying from 25 to 50 per cent. iron, and the shipping product is brought up to 60 or 65 per cent. Fe. If future economies of operation make it possible to extend this process so that 15 per cent. iron in the crude ore can be treated as a commercial success, the additional tonnage available will be enormous. A 15 per cent. Fe crude ore raised to 60 per cent. Fe concentrate with 5 per cent.

Jan 2, 1917

By W. E. C. Eustis

1st. THE fine iron ore is mixed with a sufficient proportion of fine coking coal, and is coked in any of the ordinary methods for making coke. The effect of this is to convert the iron oxide into sponge in such a shape that the usual trouble of oxidation is avoided. 2d. The resulting mixture of coke and sponge is melted down in an ordinary cupola, the coke furnishing more than sufficient fuel for that purpose. I may briefly point out here that in the first place the iron is sponged, and this sponge, as is well known, contain-, no phosphorus or silicon when the reduction takes place at a low temperature; and in the second place this sponge is melted down in a cupola in which there is no zone of reduction for phosphorus or silicon, and that con¬sequently the resulting iron should be free from both of these impu¬rities. 3d. The liquid sponge, now carburized, is run into an open-hearth furnace, where the requisite degree of hardness or softness is obtained by adding some of the fine ore, and the usual dose of ferronmanganose. I have merely given above the rough outlines of the process, but it is my intention, as early as possible, to bring the process more fully before the Institute.

Jan 1, 1881

By John C. Nigro

The Bureau of Mines is investigating the use of pulverized coal as a fuel for iron ore pelletizing to determine its effectiveness as a substitute for natural gas and oil. Experimental data illustrates the application of both a gun-type suspension burner and a cyclonic-type slagging burner to a grate-kiln pelletizing unit. In addition, experimentation with a cyclonic fired external combustion chamber for possible adaptation to a shaft or straight grate pelletizing furnace is discussed. The tests were conducted in the Bureau of Mines Twin Cities Metallurgy Research Center's pilot plant with high rank bituminous coals from Kentucky and Colorado and low rank subbituminous coals and lignites from Montana, Wyoming and North Dakota. Although combustion was excellent with the suspension burner, the low ash fusibility temperature coals and lignites caused some kiln ringing and accretion buildup in the grate kiln transfer section which were not encountered when firing with the high ash fusibility temperature Kentucky coal. Pellet contamination by coal ash was not deemed substantial. Problems with the cyclonic burner and external refractory combustion chamber centered around (a) maintaining complete combustion of the coal within the burner, (b) molten slag attack on the lower refractory chamber resulting in erosion of the lining and increased slag viscosities, and (c) freeze-up of the slag tap hole.

Jan 1, 1977

By R. C. Ellman

In the United States, the consumption of lignite and subbituminous coals is increasing. A variety of energy-oriented companies have leased large blocks of reserves, new large power plants are in operation and being constructed, and new producing mines are being developed. The Bureau of Mines has maintained an active interest in the utilization of low-rank coals for many years. In 1951, with the completion of the Bureau's Grand Forks Coal Research Laboratory, an organizational unit was established for studies in lignite preparation. Since that time, numerous investigations have been completed. This research has dealt almost exclusively with lignite, but since subbituminous coals have many similar characteristics, the findings can often be applied to both types of coal.

Jan 1, 1970

By L. M. Higgins

Dust or fume control systems are devices for capturing contaminants at their source and preventing their discharge to atmosphere. The Primary Components Of Any Dust Control System Include: An enclosure around any potential dust source such as conveyor belt transfer, crusher, screening machine, bin loading and loadout. Ductwork including hood takeoffs (transitions) to convey the collected dust laden air away from the source of dust generation to a convenient location. A dust collector for separation of particulate matter from the air stream prior to its discharge to the atmosphere. A prime mover generally a fan, to draw air into an enclosure and to overcome resistance to flow in the ductwork, dust collector and stack.

Jan 1, 1978

By John Ziats

This chapter covers the drawing requirements for the design of a comminution plant.

Jan 1, 1982

By Howard R. Hume, Terry R. West, William R. Judd

One of the outcomes of a sector slope design in a large open pit in the western United States has been the scrutiny of the structural domain concept. These domains essentially define the area of influence of particular structural characteristics. In the present instance these structural characteristics are joint discontinuities. One of the major drawbacks of defining a domain is that unless large quantities of discontinuity data are available this process of definition is largely qualitative in nature. Viewed from a discontinuity analysis aspect the orientations of all the major joint sets at a given point are a concise descriptor of the structural geologic regime at that location. This is important to domain boundary definition, this in turn is extremely important for assigning which joint sets to use as input for slope stability analysis in a given discontinuity domain. An attempt has been made to develop a quantitative method for defining these discontinuity domains based on limited amounts of orientation data thereby reducing the subjectivity normally involved in such operations. Subjectivity is not always a problem if large quantities of joint orientation data are available, since the mean and variance of joint clusters always can be compared and then grouped to define these domains. However, even this method suffers from the problem that only a single joint set orientation can be considered at a time during the grouping process. On the other hand a discontinuity domain requires that all joint sets at a point be considered simultaneously to truly define the structural discontinuity character of that point. This provides a far more complete

Jan 1, 1982

By Eugene S. Perry

The most outstanding event in oil and gas development in Montana during 1936 was the discovery of oil in the Baker-Glendive gas field, in the extreme eastern part of the state. Other notable achievements were small extensions in the Cut Bank oil field; continued favorable results of acidization in the Kevin-Sunburst oil field; and the discovery of oil and gas in commercial quantities about 20 miles southwest of Billings, on what is known as the Mosser dome. Several wildcat wells were drilled. For the coming year of 1937, it is anticipated that the main activities will be confined to drilling in or near known fields. During 1936 Montana had seven fields producing oil, but over 95 per cent of oil production came from four fields, which in order of importance are: Cut Bank, Kevin-Sunburst, Cat Creek and Pondera. Total production for the state was 5,850,893 bbl., which is 1,251,761 bbl. more than the total for 1935. Natural gas was produced and marketed from eight fields, most important being Cut Bank, Baker-Glendive, Kevin-Sunburst and Dry Creek. These four fields accounted for over 85 per cent of total state gas production, which is slightly greater than the 1935 production of nearly 18 billion cubic feet. Increase in gas consumption is due in part to increase in smelter operation. More detailed information pertaining to the various fields is given in Table 1. In the Baker-Glendive field a test 8186 ft. deep, 15 miles southeast of Baker, was completed by the Montana-Dakota Utilities Co. in 1936. The first gas-bearing sandstone (Judith Hiver horizon, Upper Cretaceous) was found at a depth of 528 ft., and a second sand at 1167 ft. Sandstones of the Dakota formation, in which occurred water, were found from 3724 to 3853 ft. White sandstone correlated with the Tensleep (Minnelusa) formation of Pennsylvanian age was found from 5631 to 5751 ft. deep. The lower 1900 ft. of the well (below 6278 ft.) was essentially in limestone and dolomite, and information on correlation of formations in this mass of sediments is not available at this time. The upper portion of this part of the well contained much anhydrite. Cherty and dolomitic limestone below 7000 ft. may be equivalent to limestones of the Madison formation. The thickness of strata beneath the Dakota formation was

Jan 1, 1937

By Donald L. Katz

THE Oklahoma City Wilcox sand, discovered on March 26, 1930, has produced 394 million barrels of crude oil and 819 billion cubic feet of natural gas as of July 1, 1941. The 100,000-bbl. wells, pressures of 2600 lb. per sq. in., and flows of "Wilcox" sand caused exciting moments in the early life of the field. Today the reservoir is substantially at atmospheric pressure and produces 75,000 bbl. of crude oil daily through 466 pumping wells. Early estimates of the initial crude-oil content of the "Wilcox" sand' indicated that about 600 million barrels of crude oil would remain after the pumping wells ceased to produce economically. The Oklahoma City Wilcox Secondary Recovery Association was organized in March 1939, to study the possibilities of recovering a portion of this oil. Only a very brief summary of the information available can be presented in a paper of this nature. Some simplification and generalizations are necessary to give the over-all picture in so short a space and statements made may not apply to a specific well or small area. Since the area under consideration by the Association is that north of the south line of section 22-11-3, some information will be presented for areas A, B, C, r, 2, 3 and part of 4 of Fig. 2, and some will be for the entire Wilcox zone west of the fault. This paper is essentially an abstract of an engineering report made by A. D. Small, B. T. Murphree, M. C. Sons and the author for the Oklahoma City. Wilcox Secondary Recovery Association on Sept. 5;.1940. Some information is taken from a report to the Association by C. V. Sidwell on March 1, 1940, and some data are from a recent report by A. D. Small. It gives a brief history of the Wilcox zone, estimates of the initial oil contents of the reservoir, present conditions in the reservoir, and probable results from several programs of "secondary recovery." HISTORY OF WILCOX ZONE The Wilcox sand lies on the flank of the general structure, as shown by cross section of Fig. 12.1 .4 and areal map of Fig. 2. The sand is of Ordivician age and is composed of well assorted, rounded' sand grains with no apparent cementing material. The loose texture of the sand is shown by the enormous quantities of sand production from the wells and from the soft cores. The productive sand varies from zero thickness on the east to 220 ft. maximum and to zero thickness on the west because of water. The development of the pool4 was dependent upon drilling restrictions within the city limits, which accounts for the spacing of drilling operations listed in Table I by years. In 1931, areas I through 7 of Fig. 2 were open for drilling with the exception of some west-edge properties, and all wells drilled before Feb. I, 1935, were in this portion of the field. Nearly all wells drilled from 1933 to 1937 were in areas A, B and C. Since 1939, the newly drilled wells have gradually enlarged the producing area toward the west in the northern portion.

Jan 1, 1941

By Charles M. Bayer

Reading in the AIME annual reports that certain activities have been financed by the Rocky Mountain Club Fund, less senior members of the Institute may wonder. "What's the Rocky Mountain Club?" Less youthful members will not have to wonder. They will recall the Club as an intriguing, almost fantastic organization, largely of western mining men, that flared across the New York horizon, flamed brilliantly for a little more than two decades, then sputtered out of existence- glorious even in its last flash. It was the only product of its mold, a fabulous group of magnanimous men who unhesitatingly sacrificed a cherished dream for which they had raised millions of dollars so that the money, instead of creating a magnificent club house, could be used instead to save the lives of starving Belgian children in World War I.

Jan 12, 1964

By William G. Pariseau

Advances in numerical methods of analysis and computer technology during the past decade have brought many formerly intractable ground control problems within easy reach of present day graduate mining engineers. However, the new technology brings with it new problems. The identity of these problems are largely those arising from a lack of familiarity with the capabilities and limitations of the new technology. In this regard, the central problem in ground control planning is the calculation of ground motion associated with mining. The fundamentals of this problem leading to a form suitable for computer programming are therefore reviewed. Solution procedures in the broad sense including the gathering of input data and the interpretation of output are described. Computer program capabilities necessary for ground control analysis are discussed and the steps necessary to implement an analysis are outlined.

Jan 1, 1983

By R. Lagneborg

WhEN mechanical twins initiate cracking it has been proposed1 that the friction stress for dislocation motion, in the Cottrell criterion for brittle fracture2 should be replaced by the stress required to propagate a twin, ttp. TF is the fracture stress, d the grain diameter, ß a geometric constant, u shear modulus, and y the effective surface energy. Since TTp is likely to vary with grain size, it cannot be substituted by a constant in Eq. [I]. If an expression for the energy change caused by a twin in a stressed material could be obtained, it is in principle possible to compute the critical size of the twin, i.e., the size at which the system can decrease its energy spontaneously, as a function of applied stress, thus giving the stress required to just barely propagate the twin, i.e., TTP. Consider a circular twin disc with a radius r and having a lenticular cross section, Fig. 1. Twin dislocations3 of strength b exist in the twin boundary parallel to the twin plane, one loop on each atomic plane. Assume that the total numbers of loops, n, can be replaced by one circular loop of a multiple dislocation, nb with a radius r. The energy change of the system, AW, due to such a twin in an applied stress field can then be calculated: The first term is the total twin surface energy, the second the elastic energy due to the twin dislocations, and the third the energy released by the twin in the applied stress field. yt is the twin boundary energy, r, the radius of the dislocation core, and T the applied

Jan 1, 1968

By G. J. Ballmer

Trucks Are Valuable Auxiliary Haulage Units in Rail Pits For: ( I ) Making railroad grades (2) Establishing benches (3) Making new dropcuts

Jan 10, 1951

By H. M. Chance

In almost all coal-fields, the quantity of explosive gases given off by the coal increases as depth is attained, requiring correspondingly enlarged quantities of air to ventilate the workings properly, by diluting and carrying off the gas. Again, with increased depth there is a corresponding increased pressure caused by the weight of the overlying strata. Sandstone or slate, which would form a good roof for a coalbed at a depth of 300 or 400 feet, may be unable to sustain the pressure of 800 or 1000 feet of overlying rock. Hence, in nearly all deep mines, the miner will generally describe the roof as "bad," although the roof-rock may be a firm slate, forming an excellent roof for workings of moderate depth, but unable to stand the pressure resulting from the weight of a great thickness of overlying rock. With increased weight of rock-mass above comes also

Jan 1, 1901

By R. B. Rosene, G. L. Foster, A. R. Hendrickson

he properties of some of the common fracturing oils, such as sand-falling rate, fluid loss and viscasity, are a function of the three major constituents of the oil. These are: asphaltic material, parafin waxes and a base oil. The base oil can be either high or low viscosity. Asphaltic material increases viscosity by thickening the oil, decreasing the rate of fall of sand through the oil. at temperatures up to 200" F. When large arnorrnts of parafin wax are present, much of the wax i.s not dissolved, but is present in the form of rnicroscopic crystals. 7'his, of course is limited to temperatures below the melting points of waxe.s. As a result, parafin waxes clo not function primarily as thickener.7, but rother as bullting materials. The functiori of wax, without asphaltic material, in a low viscosity base oil is uniquely unlike that of wax with asphalt coexistent in the oil. The resulting difierence in wax crystal size governs the sand-falling rate to a large extent. An ideal type of fracturing oil is one containing neither asphalt nor waxes. In such cases, the viscosity and resulting low sand-falling rate are apparently due to soluble resin- ous hydrocarbons, which are compatible with formation oils. INTRODUCTION Since the introduction of hydraulic fracturing as a method of stimulating production from oil and gas wells, a variety of fluids have been employed to open the fractures and carry the propping agent. Such fluids include gels, emulsions, and oils. In the latter category, the use of refined oils has increased tremendously, and it is probably safe to assume that such oils represent more than one-half of the total fluid used in fracturing. The general acceptance of refined oils for fracturing can be accounted for on the basis of their relatively low cost and general applicability. To minimize transportation costs, such refined oils are generally obtained within the local areas of operation. As a result there are several kinds of oil used in different areas, with a wide variation in the basic composition. These types may vary from a fair grade of lubricating stock to a highly viscous cut-back asphalt. or road oil. Originally, little attention was paid to the composition of the oils used for fracturing, and any oil which would carry sand was considered satisfactory. Recently, however, service companies and well operators have become more concerned with the type of oils used for fracturing. With this in mind, the present work was undertaken to evaluate and compare many widely used fracturing oils to determine which constituents were most desirable for fracturing purposes. Some of the important properties of fracturing fluids are sand-falling rate, viscosity, and fluid loss. Other properties, that are actually of no less importance, include flash point, pour point, emulsifying tendencies with formation brines, and compatability with the formation oils. This discussion has been limited, however, to the first mentioned properties in order to give some idea of the general composition of the refined oils, how they function, and why. PROPERTIES OF FRACTURING OILS The properties of fracturing oils are a function of the three major constituents of the oil. These may be designated as: (1) asphaltic material, (2) paraffin waxes and (3) a base oil, which may be of either high or low viscosity. The asphaltic material clas-

Jan 1, 1956

By Nicholas J. Palethorpe

BACKGROUND Before addressing the above topic in any detail, it is pertinent to provide some background on Australia for those people who have not been there or who have a limited knowledge of our continent. Australia is approximately the size of the continental U.S.A. (excluding Alaska) covering an area of approximately 7 million square kilometres. It has a very dry climate which has led to a concentration of people in major cities scattered around the continents perimeter. Australia's population is currently approximately 15 million. Of the work force of 6.3 million, 72% work in tertiary industries, 20.2% in manufacture, 6.5% in agriculture and 1.3% in mining. Agriculture accounts for 46% of exports, mining for 31% and manufacturing for 23,. Economic activity is based on:- Agriculture This is capital intensive and covers extensive areas and is reliant on low cost farming. A.range of foods and fibres are produced with over 70% of production being exported. Such products are of course subject to the usual vagaries of world market demand and market access, particularly in regard to the operation of trade blocks such as the E.E.C. Mineral Resources A wide range of minerals and an abundance of iron ore, coal, gas and uranium resources provide an increasing volume of exports. However, Autralia's oil resources at present only supply approximately 70% of local requirements. Industry This is diverse and encompasses the processing of agricultural products and mineral ores as well as helping to supply the consumer and capital goods needs of the whole community. However, the small scale of local markets, the geographic isolation of Australia and relatively high wage costs have limited the scale of Australia's industry. Advanced technology has overcome some of these difficulties and high tariff and import quotas protect local producers from the full force of international competition. In 1980/81 Australia's Gross Domestic Product amounted to $130 billion with approximately 24% of this being devoted to investment. In the past decade Australia has experienced inflation rates ranging from 5% to 17% and only modest real growth rates ranging from 0.4% to 5% per annum. We have also experienced, as have many other industrialised nations, continuing wage and price increases. Unemployment presently stands at 6%. MINERAL DEVELOPMENT As the above figures indicate, Australia's continuing prosperity is very dependent on the mineral and agricultrual sectors of our economy. The dependence on these sectors is highlighted by the table below which indicates our position in a global context. [Australian Production of Minerals in a World Context Western World % Total Western World Position Mineral Production 1980 1st Rutile 75 Ilmenite 31 Zircon 70 Bauxite 36 Iron Ore 11 Tungsten 14 2nd Lead (Conc.) 15 3rd Manganese Ore 14 Brown Coal 11 (1979) Zinc (Conc.) 10 4thSilver (Conc.) 10 Nickel 6 5th Tin (Conc.) 5 6th Black Coal 5 Gold 2 Source: Mining Annual Review 1981] The total value of all mineral and fuel exports in 1980/81 is estimated at $5.9 billion. This prominence in the world mineral production has largely been achieved in the last 15 - 20 years. In fact, in the early 1960's, Australia had only 2 major mining export centres, Broken Hill in New South Wales and Mt. Isa in Queensland. This growth is highlighted by the fact that in 1963, for example, we exported only 9 tonnes of iron ore and less than 4 million tonnes of coal. In 1980/81 we exported 75m. tonnes ',of iron ore (valued at $1,117m.) and 47m. tonnes of coal valued at $1,965m.). The growth in our mineral industry has come about because of a number of factors. Abundance of Mineral Resources We are particularly well endowed with mineral resources, as indicated below.

Jan 1, 1982