Search Documents

By Benjamin F. Tillson

The hammer drill rightly receives the credit for having made the one-man drill possible, and so many economies seem possible through the proper application of different types of hammer drills to various mining, quarrying, and excavating operations, that an indication of the 'economies effected by the New Jersey Zinc Co. at its Franklin mines may be of pertinent interest. When this company commenced its trials of hammer drills in 1907, these tools had not been developed to one-fourth the capacity and refinement which they have at present. At that time it was frequently stated that such a small tool, drilling holes of less diameter than the reciprocating rock drill, could not drill enough holes in a shift to permit the placing of sufficient explosive to break a tonnage of ore comparable with that produced by the "rock drills;" that the placing of small holes inclined upward, at angles steeper than 40' above the horizontal, could not be expected to produce results equal to the large flat, wet or dry, holes in the breasted back of an overhand stope, and would only shatter the ground so as to make the back unsafe. In spite of these adverse opinions, the hammer drills first showed their superiority over both heavy and light reciprocating drills in raising and in stoping, and then in drifting and quarry work. As a result, all of the reciprocating drills at the Franklin mines were scrapped three years ago, all of the mining work being accomplished with increased efficiency, as shown in detail in this article. With the advent of the hammer drill in this property, it was considered advisable to make comparative tests of all the tools accessible, and it has since been the policy to investigate the merits of any advance of the drilling art in order to get the maximum amount of work from the tools. The necessity of devising some means of standardizing drill tests, and of measuring the consumption of compressed air as well as the drilling speed, was early realized. The common test was to fill a measured air receiver with compressed air at a certain gauge pressure, run the drill until the pressure had dropped to too low a figure, then compute from the time, drop in pressure, and

Jan 1, 1915

By John S. Rinehart, Norman Ahlquist

The model which Birkimer has developed to explain the increase in fracture strength of brittle, rock-like materials with increasing rate of loading may have some applicability. It should be noted that since his analysis presupposes elastic behavior he could equally well express his result as an increase of stress to fracture with increasing strain rate, a fact which is well known. Certainly his experimental results do not contradict his strain rate to the one third power law. On the other hand, we do feel that the data are insufficient and inadequate to establish the relation- ship definitely. 'In metals, the whole fracture picture is greatly complicated by concomitant plastic flow and, in rocks, by the presence of macroscopic flaws and inhomogeneties. Both lead to uncertainties as to the state of stress during the fracture process. He quotes in support of his theory Rinehartfs results on rock in which the latter found that under impulsive loading by explosives, rocks appear to be many times stronger than under static loading. We suspect that the observed increase has little specific relevance to the theory which Birkimer puts forward. Rinehart's measurements were made by spalling rocks using a sawtooth shaped stress wave of known intensity and duration. The rise time of such a pulse is essentially zero, certainly less than 0.1 microseconds, so that it is not possible to apply Birkimerfs theory quantitatively. We favor attributing the increase in fracture strength to two factors. First, the action takes place very quickly in an exceedingly thin region so that statistically the probability is small of encountering one or more of the large flaws that contribute so significantly to the reduction of strength of most rocks under tension. It is also conceivable that the compressive wave that has just passed by the region of fracture has strengthened the rock by collapsing some of the larger flaws. Second, the state of stress obtaining at the time of fracture is not all that existing when the

Jan 1, 1971

By J. N. Hobstetter, J. J. Becker

Deformed copper single crystals exhibited, upon annealing, a recrystallized twinned grain with a twin plane parallel to an active deformation plane, rotated approximately 22" about its pole, or else did not recrystallize at all. If extraneous deformation was not carefully removed, no simple orientation relationship was found. RECRYSTALLIZATION textures have been a subject of practical interest for many years, but any real understanding of their formation will have to start with a study of the recrystallization of carefully deformed single crystals. Some efforts have been made in this direction,'-' but much more experimental information is needed before a satisfactory picture of the crystallography of recrystallization can be formed. This paper reports a few results in copper single crystals. The crystals studied in this investigation were grown by the Bridgman method," and their orientations determined by the back-reflection Laue technique." Some specimens were simply deformed in compression, others were sheared, and still others tested in a rotating-grip device, in attempts to remove end constraints. The details of their deformation behavior are described elsewhere.' The deformed specimens were annealed and the orientations of the recrystallized grains were determined optically, as described by Barrett and Levenson.8 Compressed Specimens Specimen 17-A, whose orientation is given in Fig. 1, was compressed to a total of 19 pct. As observed before,' increasing deformation took place by increasing density of slip lines in initially formed clusters, with little if any formation of new slip clusters in unslipped areas. The specimen was then etched in nitric acid until its length had been reduced from 0.766 to 0.735 in. It was annealed at 1000°C, in increments of a few minutes. After 63 min, two small grains had appeared in the center, Fig. 2. They were found to be twinned with respect to each other (AB, Fig. 4). After 30 min more, the specimen was completely recrystallized. A typical view of it is given in Fig. 3. A summary of all orientations found is given in Fig. 4, in which the prominent grain G is in (001) standard projection, and the poles of the active slip planes after deformation are indicated by SP (primary slip plane), CrSP (cross-slip plane), and CnSP (conjugate slip plane). All the orientations found were related through seven orders of twinning. A "family tree" of these twins is given in Fig. 5. Furthermore, the BG twin composition plane lies close to the cross-slip plane

Jan 1, 1954

By Charles Catlett

AN examination of the census reports' for 1880, which contain a large number of complete analyses of typical American iron-ores, indicates that the existence of barium sulphate in intimate association with iron-ore is rather unusual. Of 94 analyses reported there, but four show any barium sulphate, and the maximum content amounts to 3.04 per cent. The note of the occurrence of considerable quantities of barite in connection with certain iron-ores found in the Pinar del Rio Province of Cuba may be of interest. These deposits are found near the little village of Francisco, about 25 miles west of the city of Pinar del Rio on the Western Railroad of Havana. The principal ridges are anticlines, and consist of very thick deposits of sandy shales and slates containing a large number of little veins of white quartz which, by the gradual disintegration of the mass of the material, is left covering the surface. This quartz occasionally shows sulphide, but is generally barren of any such indication. At times lenticular masses of a more or less pure limestone were observed in these slates. The shales, which are of light color, are occasionally talcose. The formation would tentatively be classed as the Lower Cambrian, and the heavy ridges of comparatively horizontal limestone found in the anticlinal valleys as the Upper Cambrian. Along the crest of these slaty ridges deposits of iron-ore are found which are apparently in place, and were probably formed by replacement of masses of limestone similar to those noted elsewhere. The ready disintegration of the slates, and the

Jul 1, 1907

By R. F. Shurtz

This note calls attention to a contradiction in current eatistical theory and to corresponding difficulties in practice. These are significant concern in evaluating almost all ore deposits. The theoretical contradiction is that the commonly used spherical model for the semivariogram is not consistent with the usual definition of a "regionalized variable" as a mathematical function, the direct study of which "is excluded because its spatial variability is usually extremely erratic, with all kinds of discontinuities. . ." (Journel and Huijbregts, 1978). Specifically, this means a grade function that is too "rough" for interpolation to be useful. The practical difficulty is that the spherical semivariogram interprets the data upon which it is based in a manner that is, more often than not, demonstrably inconsistent with reality. This is attributable to the widely disregarded interaction between the sample pattern and the grade function. Each sample pattern "blurs" the grade function in its own particular way. It is as though the grade structure of the deposit were seen through a lens of poor resolution or reflected in a warped mirror, such as those found in amusement parks. The fitted spherical model embeds this sometimes dangerously blurred and distorted image in the Krige regression. A full analysis of these inconsistencies is to be presented later but, in the meantime, it seems urgent to communicate their effects so that those engaged in estimating ore reserves may be on guard. The spherical semivariogram has a sill and can be replaced by the corresponding covariogram. The equation of the spherical covariogram in normalized form, that is, variance and range both equal to one, is represented as: [ ]

Jan 1, 1984

By W. J. McKenna

THE International Smelting Co. concentrator at Tooele, Utah, first operated on a custom basis for the treatment of lead-zinc-iron ores on Nov.' 1, 1924, with a capacity of 500 tons per day. On May 1, 1925, the capacity was increased to 1000 tons per day by the addition of another 500-ton section. The concentrator has since operated on the two-section basis, each treating 500 tons per day entirely by flotation. LABORATORY AND TEST MILL In connection with the concentrator, a well-equipped laboratory and small continuous testing plant are maintained. The flotation equipment in the test plant is of both the Callow and Mineral Separations Sub-"A" types, so that actual concentrator conditions may be duplicated as closely as possible. PURCHASING OF ORE A new shipper usually sends to the plant a 25 to 50-lb. sample, representative of the ore to be shipped. Batch flotation tests are made on this sample to determine its amenability to the concentrator treatment flowsheet and reagent combinations. The results of these tests, which are accurately correlated with those obtained at the concentrator, both as to grades of products and recoveries, determine the actual value of the ore as submitted in the ore purchasing department's treatment schedule. Hearty cooperation has existed at all times between the ore purchasing and operating departments in the selection of ores as concentrator feed. ORE TREATED The basic tonnages for mixtures on the two sections come from the Park City and Bingham mining districts. The Park City tonnages are received by rail and consist of crude ores and gravity mill products. Those from the Bingham district are received by rail and aerial tramway,

Jan 1, 1928

By C. R. Hocott

THE distribution and movement of fluids in oil reservoirs are influ-enced to a great extent by capillary forces, which depend upon the size and shape of the pores in the reservoir rock, the surface characteristics of the rock, and the interfacial tension between the fluid phases. This paper presents the results of an investigation of the interfacial tension between salt water and crude oil containing dissolved gas under reser-voir conditions. APPARATUS AND PROCEDURE In the preliminary phases of this investigation, it was found that a scum formed at the oil-water interface, which made measurement of interfacial tension by either the ring or capillary rise methods unreliable. Accordingly, the drop-weight method, in which a fresh interface is con-tinuously formed, was selected. In this method, a tip through which drops of one fluid can be expelled is immersed in a second fluid. At the instant that the drop becomes large enough to fall, the gravitational force tending to pull away the drop exactly balances the interfacial force tending to hold it. From the size of the drop, the dimensions of the tip, and the density of the two fluid phases, the interfacial tension may be calculated. The apparatus consists of a circulating pump for bringing the oil to equilibrium with gas at the desired pressure, a displacement pump for forming the drops, an interfacial tension cell in which the drops are formed, and a density cell to determine the density of the oil. The density of the water is determined separately in another apparatus. A flow diagram of the assembled equipment is shown in Fig. 1.

Jan 1, 1938

By Heinrich Ries

In another place,* the writer has called attention to the modern methods of the laboratory investigation of clay, and it is desired here simply to discuss one branch of the subject, which, though of considerable importance, has heretofore received little attention in this country, viz., the rational analysis of clay. In order, however, the better to point out the bearings and advantages of this procedure, it is necessary to refer briefly to the ultimate analysis as well. The remarks in this paper refer only to the use of clay for the manufacture of clay-products. Pure clay or kaolin-f is extremely refractory, possesses little plasticity, and usually shrinks aud warps considerably in burning. Even the smallest proportion of impurities changes these properties, so that the kaolin exhibits variations in shrinkage, plasticity, tensile strength, fusibility, and often color when burned. The majority of nearly pure kaolins consist of kaolinite (A1,O2 2SiO,, 2H20), undecomposed feldspar, and quartz. The kaolinite generally forms the finest particles of the clay and is known as the clay-substance, while the rest of the clay-particles are collectively spoken of as sand. In the ordinary or ultimate analysis, the substances generally determined are silica, alumina, ferric oxide, lime, magnesia, alkalies and water. An analysis of this type simply regards the clay as a mixture of elements or oxides, but gives no clue as to the actual condition in which these substances exist, i.e., whether as silicates, oxides or carbonates, etc., a point which it is of the highest importance to know; for the individual components of the clay influence its properties not only according

Jan 1, 1899

By Fred C. Bond

IN crushing and grinding the larger particles are more exposed to the work input. They absorb most of the work and protect the smaller neighboring particles from destructive contact with the crushing surfaces or grinding media. The importance of this exposure differential upon the reduction efficiency and product size distribution has long been recognized. Unfortunately, there has heretofore been no direct method of evaluating it, and such indirect methods as observing the slope of the plotted product size distribution line have been used as an indication. In this presentation the Third Theory of Comminution' has been used, together with the exponential formula for size distribution, to evaluate the ex- posure ratio and exposure constant and to illustrate examples of their utility in crushing and grinding applications. The exposure ratio Er varies from zero to unity. It is zero when the product particles are all of one size, and it is unity when the work input has been equally distributed among all particle sizes. It can readily be found from screen analyses plotted according to the Third Theory. The exposure constant K is derived from the reciprocal of the exposure ratio Er. It permits more consistent predictions of size distributions and evaluation of many factors concerned in size reduction operations. The Third Theory1 states that the specific work input required for size reduction is inversely proportional to the square root of the product size less the work required to form the feed. When P represents the diameter in microns which 80 pct of the product passes, F is the size 80 pct of the feed passes, Wi

Jan 1, 1958

By Joseph Chalmers

The Petroleum Experiment Station of the U. S. Bureau of Mines at Bartlesville, Okla., has for the past three and a half years maintained a laboratory with the necessary personnel for conducting research on methods of increasing the recovery of oil. Some of the preliminary problems encountered in starting this work, with the data obtained, were discussed in A. I. M. E. Technical Publication No. 144, "Oil Recovery Investigations of the Petroleum Experiment Station of the U. S. Bureau of Mines," which was presented at the October meeting of the Institute at Tulsa, Okla., in 1928. Scope of Paper The following discussion gives some of the results of the more recent work at the Oil Recovery Laboratory. These experiments were conducted to obtain laboratory data pertaining to the relative merits or efficiencies of various pressure media in the recovery of oil from a sand reservoir. Two general types of experiments were conducted. In one the various pressure media were passed through an artificial body of sand partly saturated with oil at a constant input pressure; in the other the pressure media were passed through the body of sand partly saturated with oil at a constant volume rate. No attempt will be made to discuss the ramifications of economic problems which enter into the choice of a pressure medium. Apparatus and Materials The two 6-in. by 6-ft. flow tubes described in Technical Publication 144 were used in these experiments. They consist of 6-ft. sections of 6-in. casing with a blind flange at each end. There are three 1-in. well openings in each tube, spaced 2 ft. 4 in. apart, the end wells being

Jan 1, 1930

By A. S. Learoyd

THE Anthracite Division, Bureau of Distribution, of the United States Fuel Administration, came into existence about Oct. 20, 1917. There had been no definite policy determined upon and the distribution had been carried out by the producers and distributors of this fuel as under normal conditions. The domestic sizes had been shipped from the beginning of the coal year on Apr. 1 in about their usual proportions to the various sections of the anthracite consuming territory of this country, which, in a general way, extended as far west as Nebraska and Montana, and in the south along the Atlantic seaboard to Florida. With the advent of cold weather, about the middle of November, acute shortages commenced to develop all over the northeastern section of the country, due to largely increased demand by the public in general, to enormously increased population in centers where industrial war activity was concentrated, and by the needs of the war industries themselves. Commencing with the early part of December, this demand was aggravated by extreme low temperatures and heavy snow; and the production decreased for the same reasons. From that date until the change in the weather, about the latter part of February, it was simply a question of getting coal into communities as emergencies occurred, to take care of individual cases. No definite plan of distribution could be followed. The coal mined between Apr. 1 and Nov. 1 had been distributed as mined and, therefore, only current production was available for distribution. The Anthracite Division, during this period, consisted of a Director, two assistants, together with an office force of seven or eight clerks and stenographers.

Jan 8, 1919

By John Metz, D. E. Macdonell

The Falconbridge ore body, on the southeastern periphery of the Sudbury Basin, is definitely associated with a strong shear zone along the norite greenstone contact, in contrast to the "offset" ore bodies sometimes found in this district. To all practical intent and purpose, the dip is vertical. The ore varies in width from a few inches up to 90 ft., the average width being 15 ft. The present zone of mining operations is 6000 ft. long, 85 per cent of which develops commercial ore. The ground on the whole, and especially in the narrower widths, gives rise to reasonably strong self-supporting backs in most places, but the walls, because of strong post ore faulting on both norite and greenstone contacts, tend to be weak, and, at times, slough to a considerable extent. Obviously. then, with vertical dips, strong backs and weak sloughing walls, flat-back cut-and-fill methods are applicable to the Falconbridge ore body, and at present about 70 per cent of the stoping production is obtained in this way. The general method is described in the following pages. In actual practice, there are continual variations, as the mine staff feels that only in that way can new and better methods be developed. Source of Fill The overburden at the property consists of glacial sands and gravels, varying in depth from 00 at the outcrops, which are few and far between, to 150 ft. This condition makes for high initial cost of shaft sinking, always entailing spiling and concrete, but this extra expense is more than compensated for by the fact that the overburden is the source of very cheap fill.

Jan 1, 1946

By Joseph C. Mead, James R. Cudworth

THE Birmingham district of Alabama has utilized the slag from its blast furnaces consistently since the earliest development of the slag industry. Today there are producers of slag cement who started business in 1900, and who have, under a progressive policy, expanded the number of their products to meet present demands. There are producers of slag aggregates and other crushed slag products who have been successful for periods of over thirty years. There are at the present two companies, Cheney Lime and Cement Co. and the Southern Cement Co., manufacturing puzzolan cement; two companies, Birmingham Slag Co. and Woodstock Slag Co., making slag aggregates and by-products; one company, Tennessee Coal, Iron and Railway Co., a subsidiary of the U. S. Steel Corporation, producing ground open-hearth basic slag for soil conditioning. Two companies, the Sloss Sheffield Steel and Iron Co. and the Woodstock Slag Co., make slag concrete in ready-mix plants and one company, the Superock Company, manufactures fine and coarse slag aggregates under a new granulation process. No Portland cement is made with slag as an ingredient, because dolomite is used so extensively as a blast-furnace flux that the magnesium content of the slag is excessive. Sources Of Slag In the Birmingham district there are 22 blast furnaces, of which the majority are in blast. The present production is 165,000 tons of pig iron monthly; the production in 1935 was 1,297,960 gross tons1. There are also two blast furnaces at Gadsden and one ferroalloy electric furnace at Anniston. From these two sources is obtained slag to approximately 1.1 tons per ton of pig iron.

Jan 1, 1937

By F. W. Osterwald, C. R. Dunrud

A continuously recording seismic network was constructed in 1962 by the U.S. Geological Survey to locate epicenters and record incidence of bumps (bounces, rock bursts) that occur in the bituminous coal mines of the Book Cliffs coal field near Sunny-side, Utah. The coal is mined because of its value as coking coal, although these bumps may be a hazard to life and property. Daily records of tremors caused by bumps for 1 3/4 years indicate that a seasonal pattern, as well as a daily pattern, exists for the number of bumps that occur in a given period. Maxima occur in May and June and November and December. Marked increases at 5-day to 9-day intervals are superimposed on these seasonal maxima. The largest bumps commonly occur during seasonal maxima when the rate of occurrence suddenly decreases and the amplitude of the individual bumps increases. Knowledge of this pattern may lead to prediction of general locations and periods of increased hazard from bumps. Experience to date has shown that prediction of precise times and locations of hazardous bumps is not possible, and may never be; primarily because even a small bump can be a hazard to life and property. Some bumps or bump sequences are actually composites, consisting or two or more discrete bumps a few tenths of a second to a few seconds apart. Violent and spontaneous releases of coal and rock from faces, ribs and roofs of mines (termed bumps or bounces by miners) are a common hazard to life and property in the coal mines located in the Book Cliffs near Sunnyside, Utah (Fig. 1). These bumps

Jan 1, 1965

By W. G. Scott

Since devising the incline top-slicing method in use at the Coronado mine,l I have had numerous inquiries as to how the same system could be adapted to larger orebodies. Based upon our experience here, I have outlined below some suggestions for its application to orebodies of larger size. Modifications and extensions, of course, would have to be made to take care of different dimensions and irregularities. In order that one may have a better understanding of the scheme, a brief description of the Coronado method will be given first. CORONADO METHOD The portion of the Coronado vein that is worked by the slicing system ranges from 20 to 40 ft. (6 to 12 m.) in width. Preparatory work in this orebody consists of driving sub-levels every 55 ft. (1 6.77 m.) vertically, or in multiples of 11 ft. (3.36 m.) (which is the height of a slice). These levels are usually driven along the hanging wall until the end of the orebody is reached. Crosscuts, at right angles to the strike, 50 ft. (15.24 m.) apart, are then run from wall to wall, or until the lean ore is reached. They are run in the middle of the block, which is 50 ft. in length and the width of the vein. The crosscut on the hanging-wall side is extended in the wall a short distance for a manway and timberway raise. This raise is carried up in the wall to the sub-level above, leaving a pillar about 5 ft. in thickness between it and the vein. Connections are made every 11

Jan 1, 1918

By Miguel Bustamente

In 1890 I mas manager of a mining enterprise in the State of Michoacan. The ores were composed principally of iron pyrites (much decomposed), in a quartz matrix, with native gold in very irregular grains. Some portions, however, carried their metallic value in a matrix of calcite arid siderite. The mill in which the ores were treated consisted of two 800-lb. stamps, two amalgamating-plates, four pans, two automatic washers, two Frue vanners, and the necessary accessories for assaying, retorting and refining gold. The plant, originally erected with American capital, and directed by competent Americans, passed in 1890 into the hands of Mexican owners. On taking charge of the business I found on hand a large amount of ore assaying 35 grammes of gold per metric ton (about 1 oz. Troy per ton of 2000 lbs.); but the company was losing money, and was about to abandon the business. Obviously, the difficulty lay in the treatment of the ore. The extraction of gold scarcely reached one-tenth of the assayvalue ; the loss of mercury was considerable; and high freight; charges excluded the alternative of exporting the ores. This situation naturally suggested that amalgamation was not applicable to these ores, and that a more appropriate method must be adopted. The cyanide- and chlorination-methods had been tried already, without practically satisfactory results. For the first few months I employed a combined system, extracting a part of the gold by direct amalgamation, and cyaniding the concentrates. This saved 32 per cent. of the assay-value, but the cost of milling still exceeded the proceeds. Meanwhile I observed

Jan 1, 1902

By Dwight Farnham

Description of Quarry THE shale used at the Renton plant of the Denny-Renton Clay Coal Co., for the manufacture of vitrified paving brick occurs in a hill rising from 200 to 300 ft. above the level of the valley in which the plant is situated. The shale deposit, which is of unknown thickness pitches about 10° to the southeast. The 150-ft. face worked extends approximately east and west, so that the clip, as shown by the photograph, is to the left and into the hill. The shale is overlain with about 50 ft. of gravel, 70 ft. of clay, and 30 ft. of mixed loam and gravel, making altogether from 125 to 150 ft. of overburden. Disposal of Overburden The overburden is removed by sluicing. For this purpose a No. 2 Joshua Hendy giant is used, throwing a 12-in. stream', and having 60 lb. pressure at the nozzle. The water is drawn through an 8-in. pipe from Cedar river, about 1,000 ft. distant, by means of a Worthington four-stage centrifugal pump, direct connected with a 100-h.p. motor placed just south of the factory, and 1,500 ft. from the nozzle This plant handles the material satisfactorily to a height of about 75 ft. above the level of the top of the shale. When the higher levels are worked, an auxiliary plant consisting of a four-stage Byron Jackson centrifugal pump with a 100-h.p., belt-connected motor, is thrown into the system. This plant is situated on top of the shale and can be discerned at the extreme right of the trestle work in Fig. 1.

Jan 9, 1914

By Bror Nordberg

SAND and gravel are unconsolidated granular materials resulting from the natural disintegration of rocks. The two materials nearly al- ways occur together, variably proportioned in widely available de- posits. A commercial sand comprises the fine granular material, usually less than f in. in diameter (ASTM Designation C58-28), and gravel consists of the coarse, granular material larger than sand (ASTM Designation C125-46T). Gravel falls within the range of 1/4 in. and a top size usually of 3 ½ in. Chemical definition is impossible. Sand and gravel are always of secondary origin. They were formed from various massive rocks through the action of chemical and mechanical forces; then transported, abraded, washed, sorted, and classified by streams, glaciers, waves, or winds, to be redeposited in beds as they are found. Chief disintegrating forces in the reduction of rocks into granular particles were frost, rain, the dissolving action of acid and alkaline ground waters, the mechanical action of streams and waves, and the action of glaciers. Method of formation and deposition have imparted physical properties to sands and gravels that largely determine the commercial value of the materials for particular use and influence the manner of exploitation. In the early days of the commercial industry, purchasing specifications were relatively lenient but in. the past decade much more rigid quality requirements have had to be met for acceptance by all classes of purchasers. The trend to further severity in requirements is a challenge to the industry that commands full knowledge of the nature of raw materials at hand and skillful application of processing into commercial products. Mechanical strength, the ability to resist disintegration, chemica

Jan 1, 1949

Draftsman and transitman for coal-mine work in middle West. Salary $125 per month. No. 277. Surveyor and mine sampler for development company in Mexico. Applicant must be willing to interest himself in mine sufficiently to, act as assistant to the superintendent and be able to take charge in case the superintendent should be incapacitated at any time. No. 326. A copper company in Mexico desires services of engineer to act as chief chemist and flotation operator. No. 327. Instructor in mining and metallurgy, the work being chiefly in mining for college in middle West, to start Dec. 1. Salary $1200 to $1400. No. 328. A copper company in Mexico is increasing its force of underground foremen and desires the services of two men competent to act as assistant underground foremen. Chances for advancement excellent. Knowledge of Spanish is required. Salary to start $200 per month. No. 329. Young man for core-drill work for coal company. No. 330.

Jan 7, 1918

By A. P. Watts

FOREWORD THE problem of concentrating the disseminated lead ore of southeast Missouri is extremely simple. The economic mineral is galena and the gangue is dolomite. The ore assays from 4 to .6 per cent. lead, 80 per cent. of which is recovered in a 70 per cent. concentrate.. The ore is crushed through 10 mm. and sized on 2 mm.; the oversize is jigged, while the undersize is tabled, and the slime treated by flotation. The district is the largest lead producer in the world, the output of metallic lead for the year 1915 being 183,906 tons. Over 20,000 tons of ore a day is being treated. The management of the different properties is progressive and always open to suggestion. The fact; however, must not be lost sight of, that the problem in the district is peculiar, as the average ore contains but 80 to 120 lb. of a metal normally selling at about 4c. per lb. The low price of the metal limits the treatment system to one of low cost. An elaborate treatment is neither logical nor advisable. An engineer first visiting the district may consider that the method of treatment could be improved

Jan 10, 1917