Search Documents

By D. B. Jugle, J. B. Darby

The equilibrium solubility limits of the transition elements Ti, V, Cr, Fe, and Co in liquid tin were determined in the temperature range from 827" to 1211°K. Since the equilibrium concentration of Ti, V, or Cr in liquid tin is moderately dilute in the temperature range investigated, the solubility data were employed to estimate the partial molar enthalpy and the partial molar excess entropy of solution for the three solutes in liquid tin. The reference state s for titanium or vanadium were selected relative to the solute in an intermetallic compound. The thermodynamic quantities for chromium were calculated relative to pure chromium. RECENT experiments1 have shown that the rate of solution of several transition elements in liquid aluminum can be qualitatively predicted from a knowledge of the temperature dependence of the solvent-rich liquidus. In order to extend the analysis to binary tin systems,' it was necessary to know the equilibrium solubility of several of the first-long-period transition elements in liquid tin. Since solubility data for the tin-rich portion of binary systems are meager, the present investigation was undertaken to determine the equilibrium solubility limit of Ti, V, Cr, Fe, and Co in liquid tin in the temperature range from 850" to 1200°K. EXPERIMENTAL PROCEDURE A useful technique3 to determine the equilibrium solubility of a solute in a liquid-metal solvent consists essentially of placing a pure solute in contact with a pure solvent and allowing sufficient time for equilibrium to be attained at the temperature of interest. Subsequently, the solvent is removed and the equilibrium solute concentration in the solvent is determined by an appropriate analytical procedure. The technique can be applied very successfully to relatively simple systems such as the copper-germanium system.3 However, in many binary systems of transition elements with tin, several intermediate phases are known to exist and precipitation of the phases from solution, in solubility experiments, can lead to an erroneously large solubility. The difficulty was avoided in the present work by equilibration of the most solvent-rich intermediate phase with the pure solvent over a range of temperatures. The compounds employed in this investigation, and the temperature range over which each compound is in equilibrium with liquid tin are listed in Table I. No stable intermediate phases are reported in the chromium-tin system4 and, therefore, pure chromium was utilized as the solute. The stoichiometric compounds were prepared by arc-melting on a water-cooled copper hearth in a helium-argon atmosphere. The elemental tin employed in.this investigation was 99.998 pct pure, and typical lot analyses of the transition elements were reported elsewhere.' A sample of an appropriate solute, in the form of a button and in sufficient quantity to exceed the equilibrium solubility, and the pure tin solvent were placed in a high-purity recrystallized-alumina crucible. The crucible and contents were placed in a horizontal furnace under a high vacuum (10-6 torr) and held at temperature for periods varying between 24 and 72 hr. A water-cooled quench tank, partially filled with diffusion-pump oil, was attached close to one end of the

Jan 1, 1970

By D. W. Levinson, L. E. Tanner

DURING the course of an investigation of the zirconium-iron-tin system the zirconium-iron system was reexamined up to 55 pct* Fe. The alloys pre- visible melting3 and X-ray diffraction studies were made of samples of the alloys. The ferromagnetic properties of ZrFe2were determined by Professor P. W. Selwood* using a modified Faraday balance.4 The zirconium-rich portion of the phase diagram is presented in Fig. 1 and compared with the work of Hayes et al.1 The maximum solubility of iron in ß is somewhat decreased while the eutectic temperature is raised. There seemed to be no change in the eutectic composition of 16 pct Fe. Since the base material was so low in iron content, it was possible to establish the maximum solubility in a between 0.017 and 0.025 pct Fe at the eutectoid temperature. The observation of fine ZrFe, particles in the micro structure of a specimen of 0.012 pct Fe alloy quenched from 700°C indicated that the solubility drops below this composition at 700° C and lower. Further study was made of the intermediate phase ZrFe2. wallbaum5 identified the compound initially as ZrFe2 with a C 15 (MgCu2) structure, placing it at 55 pct Fe stoichiometrically. Hayes et al.1 believed they found the phase at about 47.2 pct Fe and called it Zr2Fe3 but reverted to ZrFe, in the discussion of their paper.6 Jordan and Duwez7 confirmed Wallbaum's work as well as finding the same single-phase structure to about 62.3 pct Fe or Zr0-61 Fe2-18. In order to establish the ternary phase relations in the zirconium-iron-tin systema the exact position of this phase had to be known. This was accomplished by X-ray diffraction, visible melting, and metallographic techniques. Elliott8 obtained a single-phase ZrFe2 X-ray diffraction pattern from an alloy of about 55 pct Fe. This was confirmed in the present study with an alloy of 54.81 pct Fe. However, extra lines (attributable to a or ß zirconium) were found in diffraction patterns of the 47.42 and 49.83 pct Fe alloys. The melting characteristics of these same alloys were studied by suspending 47.42, 49.83, and 54.81 pct

Jan 1, 1960

By A. R. Troiano, A. B. Greninger

There is need for an adequate working hypothesis that would describe at least qualitatively the crystallographic mechanism for the transformation from austenite to martensite in steel. A general theory would not only be of great assistance in the correlation of existing data and in planning future experimentation, but would also form the basis for an eventual explanation of the property changes that accompany lattice transformations. The mechanism of martensite formation described in the following pages is the outcome of two new experimental determinations: (1) the accurate evaluation of the lattice relationship between austenite and individual crystals of martensite, and (2) the measurement and analysis of the change in position that a volume of austenite undergoes when it transforms into a crystal of martensite. For this latter study, the stereographic analysis of shear was employed; this method greatly simplifies the solution of lattice-shear problems, and some space is devoted to its description. Lattiice Relationships and Habits PREVIOUS WORK The lattice relationships between austenite and martensite in carbon steels have been studied by Kurdjurnow-and Sachs,' and by Wassermann;2 and in iron-nickel alloys by Nishiyama.3 Wassermann,2 and Mehl and Derge.4 The studies by Kurdjumow and Sachs and by Wassermann were made on single (austenite) crystals of quenched 1.4 pct carbon steel, and the results of these two independent studies agree closely with the postulated lattice relationships: (III)r||(0ll)a [101]r [111]a [1] Both Nishiyama and Wassermann worked with an alloy of iron plus 30 pct nickel (all austenite at room temperature), and "martensitic alpha" was formed by cooling in liquid air. They agree that the lattice relationships for these conditions are: (lll)r||(011)a [112]r[011]a [2] Mehl and Derge worked with a range of iron-nickel alloy compositions centered about 30 pct nickel. They concluded that when the transformation takes place near room temperature or above, relationship [l] holds, but if the same specimen is made to transform at -195°C, relationship [2] obtains;intermediate temperatures evidently produced a combination of these two relationships. Sachs and co-worker~,1,7 as well as Nishiyama,3 have proposed transformation mechanisms for martensite formation.* Both of the mechanisms picture the transformation as initiated by shearing movements along the octahedral [Ill] plane of austenite, followed by suitable expansion and contraction to complete the transformation. These mechanisms have been described and commented upon by Mehl, Barrett, and Smith,8 Mehl and Derge,4 Wassermann,2 and others, and generally accepted by investigators in this field. Greninger and Troiano9 have recently published the results of a detailed study of the shapes and orientation habits of martensite crystals in plain-carbon and nickel steels. They found that, contrary to previous assumptions, martensite plates form not along the octahedral planes but along austenite planes of very high indices; these results were in line with those of previous studies of martensite reactions in nonferrous alloy systems by Greninger and coworkers.6,10 Greninger and Troiano concluded that the transformation theories of Kurdjumow and Sachsl and of Nishiyama3 are untenable. Phragmén11 reached a similar conclusion. EXPERlMENTAL METHODS The object of this particular study was the evaluation of (1) lattice relationship between austenite and martensite, and (2) relationship between the martensite lattice and the martensite plate. The technique used for solving these problems was similar to that used by Greninger6 on martensitic structures in 8 copper-aluminum alloys. Briefly, the method consists of grinding and polishing a specimen on a surface parallel to an individual martensite plate and thus exposing a single martensite crystal for an area of l to 3 mm. The orientation of this exposed martensite crystal is then determined by means of a back-reflection Laue X ray pattern.12 Another pattern is obtained from the matrix crystal, and a stereo-graphic plot of data from these two patterns then provides the solution to the problem. It is necessary to repeat this process on several crystals in order to determine whether or not the solution is unique.

Jan 1, 1950

By William A. West

One manifestation of anelastic properties in solids is the mechanical elastic aftereffect, which may be described briefly as follows: If a stress is applied to a solid body, a deformation or strain is produced. On removal of the stress, this deformation disappears, at least in part. As a first approximation, this appearance or disappearance of deformation usually has been considered instantaneous. Actually, however, for a very wide variety of substances, on application of stress the instantaneous deformation is followed by a further slow yielding, which continues, although at a rapidly diminishing rate, for as long as the stress is applied. Similarly, on removal of the stress, the instantaneous recovery from deformation is followed by a further slow recovery, which continues, although at a rapidly diminishing rate, often for a long time. This latter phenomenon has been called the "elastic after-effect." Experiments upon the elastic after-effect in metals, when properly designed and when properly interpreted, are capable of giving quite precise information regarding the relation between stress and strain in the various constituent parts of the metal. For example, if certain parts of the metal, such as grain boundaries or slip bands, behave in a viscous manner—that is, if therein—the relaxation spectrum will contain lines or bands associated with the relaxation of shear stress within these parts. No attempts have heretofore been made to utilize elastic after-effects for obtaining such detailed information. The purpose of the present paper is to explore the possibilities of properly designed and interpreted experiments on the elastic aftereffect in metals. Since new procedures and principles are employed in this study, an attempt has been made to record each step taken. Elastic after-effect observations are susceptible of simple interpretation only when the stress level employed is so low that all effects are linear with the stress. Just how low the stress level must be can he determined only by experiment. An advnntage, other than simple interpretation, is associated with low stress levels. When all effects are linear, derived quantities, such as the relaxation spectrum, are independent of the stress distribution. It is, furthermore, possible to employ the type of deformation that is most convenient from the experimental standpoint; for example torsion. It appears that in experiments involving both loading and unloading the following would be observed: I. Instantaneous deformation, recoverable instantaneously in whole, or in part. 2. Delayed deformation, recoverable slowly in whole, in part, or not at all. 3. Permanent deformation, the difference between total deformation and total recovery. In the work here described, unloading experiments only were made. Wires were

Jan 1, 1947

By William A. West

One manifestation of anelastic properties in solids is the mechanical elastic aftereffect, which may be described briefly as follows: If a stress is applied to a solid body, a deformation or strain is produced. On removal of the stress, this deformation disappears, at least in part. As a first approximation, this appearance or disappearance of deformation usually has been considered instantaneous. Actually, however, for a very wide variety of substances, on application of stress the instantaneous deformation is followed by a further slow yielding, which continues, although at a rapidly diminishing rate, for as long as the stress is applied. Similarly, on removal of the stress, the instantaneous recovery from deformation is followed by a further slow recovery, which continues, although at a rapidly diminishing rate, often for a long time. This latter phenomenon has been called the "elastic after-effect." Experiments upon the elastic after-effect in metals, when properly designed and when properly interpreted, are capable of giving quite precise information regarding the relation between stress and strain in the various constituent parts of the metal. For example, if certain parts of the metal, such as grain boundaries or slip bands, behave in a viscous manner—that is, if therein—the relaxation spectrum will contain lines or bands associated with the relaxation of shear stress within these parts. No attempts have heretofore been made to utilize elastic after-effects for obtaining such detailed information. The purpose of the present paper is to explore the possibilities of properly designed and interpreted experiments on the elastic aftereffect in metals. Since new procedures and principles are employed in this study, an attempt has been made to record each step taken. Elastic after-effect observations are susceptible of simple interpretation only when the stress level employed is so low that all effects are linear with the stress. Just how low the stress level must be can he determined only by experiment. An advnntage, other than simple interpretation, is associated with low stress levels. When all effects are linear, derived quantities, such as the relaxation spectrum, are independent of the stress distribution. It is, furthermore, possible to employ the type of deformation that is most convenient from the experimental standpoint; for example torsion. It appears that in experiments involving both loading and unloading the following would be observed: I. Instantaneous deformation, recoverable instantaneously in whole, or in part. 2. Delayed deformation, recoverable slowly in whole, in part, or not at all. 3. Permanent deformation, the difference between total deformation and total recovery. In the work here described, unloading experiments only were made. Wires were

Jan 1, 1947

Jan 1, 1971

By Bruce W. Gonser, Robert I. Jaffee

Recent work by the authors1 established the constitutional diagram of the gold-germanium system. Of particular interest in the simple euctectiferous system was the eutectic alloy at 12 per cent Ge, which melted at the very low temperature of 356°C and had an unusually fine eutectic structure. It was of interest to investigate the effect of third components on the melting point, microstructure, and strength of this alloy, and in this work the effect of copper is discussed rather completely, with less complete data on the effects of silver, platinum, nickel, and zinc. No reference in the literature has been found on ternary systems with gold-germanium. Materials and Alloying -4s in the work on the binary system, gold-germanium, the germanium used in this investigation was the cyanide-reduced, 99.9 per cent product, produced by the Eagle-Picher Co. Fine gold sheet from Handy and Harmon, pure platinum sheet from the American Platinum Works, copper magnet wire from Anaconda, nickel wire assaying 99.6 per cent Ni. and electrolytic zinc were used for alloying. To make the alloys, charges of the pure metals were put in a graphite crucible and melted in an atmosphere of pure hydrogen. The temperature was brought up to about I050 C, and the metal allowed to freeze in the crucible. Except with alloys containing zinc, melting losses were consistently less than a few milligrams. When zinc was a component, weight losses up to half the weight of the zinc present were incurred, and the alloy compositions were calculated by assuming the entire weight loss to be that of zinc. In all other cases the composition of the alloys could safely be taken as that of the charge. The ingots, as solidified, were segregated, the heavier primary phases being at the bottom and sides of the ingots and the lighter primary phases at the top, but by sectioning the entire ingot vertically for microscopic examination, this factor could be evaluated. Ingots for microscopic examination weighed one gram, and those for thermal analysis weighed three grams. Thermal Analysis In this work, the eutectic line composition and thermal arrests were desired, and, after microscopic exploration had established the position of the eutectic line at a given percentage of the third component, a thermal analysis was run at that composition. The method of thermal analysis used in the work on the binary Au-Ge system,' a method particularly well suited for a small quantity of material, was used in this work. Clearly defined arrests were obtained, although with some alloys containing platinum

Jan 1, 1946

By Robert I. Jaffee, Bruce W. Gonser

Recent work by the authors1 established the constitutional diagram of the gold-germanium system. Of particular interest in the simple euctectiferous system was the eutectic alloy at 12 per cent Ge, which melted at the very low temperature of 356°C and had an unusually fine eutectic structure. It was of interest to investigate the effect of third components on the melting point, microstructure, and strength of this alloy, and in this work the effect of copper is discussed rather completely, with less complete data on the effects of silver, platinum, nickel, and zinc. No reference in the literature has been found on ternary systems with gold-germanium. Materials and Alloying -4s in the work on the binary system, gold-germanium, the germanium used in this investigation was the cyanide-reduced, 99.9 per cent product, produced by the Eagle-Picher Co. Fine gold sheet from Handy and Harmon, pure platinum sheet from the American Platinum Works, copper magnet wire from Anaconda, nickel wire assaying 99.6 per cent Ni. and electrolytic zinc were used for alloying. To make the alloys, charges of the pure metals were put in a graphite crucible and melted in an atmosphere of pure hydrogen. The temperature was brought up to about I050 C, and the metal allowed to freeze in the crucible. Except with alloys containing zinc, melting losses were consistently less than a few milligrams. When zinc was a component, weight losses up to half the weight of the zinc present were incurred, and the alloy compositions were calculated by assuming the entire weight loss to be that of zinc. In all other cases the composition of the alloys could safely be taken as that of the charge. The ingots, as solidified, were segregated, the heavier primary phases being at the bottom and sides of the ingots and the lighter primary phases at the top, but by sectioning the entire ingot vertically for microscopic examination, this factor could be evaluated. Ingots for microscopic examination weighed one gram, and those for thermal analysis weighed three grams. Thermal Analysis In this work, the eutectic line composition and thermal arrests were desired, and, after microscopic exploration had established the position of the eutectic line at a given percentage of the third component, a thermal analysis was run at that composition. The method of thermal analysis used in the work on the binary Au-Ge system,' a method particularly well suited for a small quantity of material, was used in this work. Clearly defined arrests were obtained, although with some alloys containing platinum

Jan 1, 1946

By Herbert Clark Hoover, Lou Henry Hoover

MOST illustrious Princes, often have I considered the metallic arts as a whole, as Moderatus Columella2 considered the agricultural arts, just as if I had been considering the whole of the human body ; and when I had perceived the various parts of the subject, like so many members of the body, I became afraid that I might die before I should understand its full extent, much less before I could immortalise it in writing. This book itself indicates the length and breadth of the subject, and the number and importance of the sciences of which at least some little knowledge is necessary to miners. Indeed, the subject of mining is a very extensive one, and one very difficult to explain ; no part of it is fully dealt with by the Greek and Latin authors whose works survive ; and since the art is one of the most ancient, the most necessary and the most profitable to mankind, I considered that I ought not to neglect it. Without doubt, none of the arts is older than agriculture, but that of the metals is not , less ancient ; in fact they are at least equal and coeval, for no mortal man ever tilled a field without implements. In truth, in all the works of agricul- ture, as in the other arts, implements are used which are made from metals, or which could not be made without the use of metals ; for this reason the metals are of the greatest necessity to man. When an art is so poor that it lacks metals, it is not of much importance, for nothing is made without tools. Besides, of all ways whereby great wealth is acquired by good and honest means, none is more advantageous than mining ; for although from fields which are well tilled (not to mention other things) we derive rich yields, yet we obtain richer products from mines ; in fact, one mine is often much more beneficial to us than many fields. For this reason we learn from the history of nearly all ages that very many men have been made rich by the

Jan 1, 1950

By R. Hoffmann

The Waelz process produces oxides of volatilizable metals from ores, metalliferous products and residues. The process was originally used for recovering zinc and lead, where tailings and residues containing those metals had accumulated at mines or smelters, but it is applicable for obtaining tin, arsenic or other volatilizable metals. It is useful when other methods of obtaining the metals from the ores or residues are too difficult or expensive or show too low a recovery. The Waelz process was developed in 1923 for the treatment of large calamine dumps in Upper Silesia, which showed zinc contents of 8 to 10 per cent. and lead contents up to 3 per cent. The rapid development of the process, from the first trials up to the plants now working or in course of erection, is shown in Fig. 1. The first industrial Waelz plant was started in 1925. Within two years the capacity of the working plants reached 700 tons material per day of 24 hr. During the year 1928 the daily capacity of the plants now at work or in course of erection will rise

Jan 1, 1928

By G. Townsend Harley

STOPING methods in which shoveling plays an important part are gradually being replaced by other and cheaper methods. But there will always be considerable shoveling done underground in stopes as well as in drifts, tunnels, urinzes, and shafts. At the mines of the PhelpsDodge Corporation at Tyrone, N. M., the cost of shoveling in all stopes in 1917 amounted to 24c. per T. In the top-slice stopes for the same period, it cost 27 c. per T. or 16 per cent, of the total cost of these stopes. The tonnage for shovelers from all stoping was 9.3 T. per man, and for topslicing 8.2 T. per man. These stopes were not unduly hot, and there was not more than the usual amount of timber to interfere with the work of the men. The tonnages obtained per shoveler were considered low; first, because of a poor grade of Mexican labor, many of the men having come in from railroad grading camps; and second, because of a poor spacing of raises, especially in the top-slice stopes, where, in general, they were spaced 25 ft. by 66 ft. (7.6 by 20.1 m.) centers. The average wage per laborer shift was $2.67 during the year. It was thought, however, that even under these conditions the men were not producing the tonnage that they should, so, with the consent of the management, the writer undertook to determine how the general efficiency of the underground shoveling could be improved. No predetermined plan for conducting these experiments was arranged because we had no definite ideas as to the scope of the work or the number of elements into which the investigation would resolve itself, before all of its phases could be determined. We were sure, however, that any work that would thoroughly cover the ground would have to be in the nature of a systematic time study, combined with a course of instruction in correct shoveling methods and adequate and intelligent supervision of the work. Two or three companies in the Southwest have done some work to determine the proper shovel to be used undcrground, but so far as is known the work has been limited to equipping certain parts of their mines with a particular type and size of shovel and thereafter watching the cost and efficiency records. In each case it seems to have been the shovel that held the 21-lb. (9.5-kg.) load that gave the bcst results. Excepting personal communications from these companies, the only data available on scientific shoveling are contained in F. W. Taylor's book, "The Principles of Scientific Management," and D. J. Haucr's article, in The Contractor for March 29, 1918, "A Hundred Hints for Shovelers." This paper discusses and draws conclusions from several thousand time-study readings, taken both on the surface and in the mines for nearly a year. A sufficient number of readings were taken on each factor in the problem for the plotting of curves of the performances and to obtain accurate indices of the work to be expected from this class of labor. The work is not as complete in all of its details as we would like to havc it, because we were forced to stop the work temporarily, owing to the numbcr of men going into the National service and our inability to get others who could make time studies. The results obtained so far, however, have been of such a startling nature that we have decided to submit them at this time, subject to future modification. It is hoped, also, that a free discussion of this paper will lead to a disclosure of any errors that may have becn embodied and offer some valuable suggestions for the conduct of future work.

Jan 1, 1920

By Irving Cadoff, Kurt Komarek, Edward Miller

THE lead-telluride phase diagram as compiled by ansen' has one intermetallic compound, PbTe, with solid-solubility limits extending from 22 to 45 wt pct Te (31.4 to 57.1 at. pct). Pelzel2 redetermined the solubility limits on the lead-rich side of the compound by measuring the relative areas of the two phases in samples annealed in the liquid + compound region, and obtained data that agreed with that of Hansen. Recent studies of the semiconducting properties of PbTe3 however, have indicated that addition of either lead or tellurium to PbTe does not produce samples having carrier concentrations greater than about 10 19 cm-3. Assuming that each impurity atom results in one ionized charge carrier, this carrier concentration corresponds to a solubility range of less than 0.04 at. pct. Fritts and Karrar4 have also observed two phases in samples containing from 0.15 to 3.0 pct excess Pb. To resolve the discrepancy between these data, the solid solubility limits of the compound PbTe were reinvestigated, using several other techniques. Ten 25-g samples with compositions of 1/2, 1, 3, 5, and 10 wt pct excess Pb and Te and two 100-g samples of 15 and 65 wt pct Te were prepared, sealed in evacuated quartz capsules, and melted at 950oC. The 1 pct excess Pb and Te and the 15 and 65 wt pct Te alloys were homogenized for 96 hr at 450°C; the remaining specimens were annealed 50°C below the solidus temperature reported in Hansen. The specimens were polished and etched with dilute HNO,. All the samples were two phase, the second phase appearing at grain boundaries or as spheroidized inclusions in the grains. In the case of the tellurium rich specimens, the second phase could be identified as a eutectic. Debye-Scherrer powder diffraction patterns of the i, 1, 3, 5, and 10 pct excess samples were obtained using CuKa filtered radiation. The films were indexed as the B1 or NaCl structure. The calculated lattice parameter of PbTe was the same for all the specimens, with an average of a0 = 6.460 ± 0.0005A. Lines due to excess lead or tellurium were very faint but could be clearly seen in all the films. The relative areas of the two phases in the 15 and 65 wt pct Te samples were corrected for the differences in density of Pb, Te, and PbTe, and taken as proportional to the relative volumes of the two phases. The corrected relative volumes agreed with a phase diagram having negligible solubility of both lead and tellurium in lead tellurium. The density of the two specimens was obtained to give a third independent determination of the phase limits. The specimens were broken into small pieces to eliminate any internal porosity, and adherent air bubbles were removed by vigorous shaking under water for several hours. The density of lead (11.34 g per cm3) and of tellurium (6.25 g per cm3) was taken from the International Critical Tables and that of stoichiometric PbTe (8.25 g per cm3) calculated from the lattice parameter. For the 15 wt pct Te samples, the density assuming no solubility was calculated to be 9.89 g per cm3; the observed density was 9.86 g per cm8. For the 65 wt pct Te alloy, the density calculated for the case of no solubility was 7.24 g per cm3; the measured density wag 7.22 g per cm3. These results are consistent with those of planimetry and X-ray. SUMMARY Data have been presented which show that the solid solubility of both lead and tellurium in PbTe is

Jan 1, 1961

By W. F. Hosford

A series of aluminum single crystals was subjected to axially symmetric flow by drawing through dies. The orientation dependence of the drawing stress, which indicates the resistance to this type of flow, compares reasonably with predictions of Taylor and of Bishop and Hill. Measured lattice rotations likewise are generally consistent with theory. The most successful analyses of the plastic behavior of polycrystalline metal and its relationship to single crystal behavior are those of Taylor1-3 and of Bishop and Hill.4-6 The purpose of this paper is to provide a critical test of some of the basic assumptions involved in these theories. Both treatments apply to fcc metals and assume the shape change of each grain in a polycrystal to be the same as that of the polycrystal as a whole. Thus for a randomly oriented polycrystal extended under uni-axial tension each grain is assumed to undergo axially symmetric flow. dey = dez = -1/2dex, deyZ = dezx = dexy = 0 [l] where x, y, and z are a set of orthogonal axes, x being the tensile axis. Although [011.] oriented grains in bcc and fcc metals may depart markedly from this ideal behavior,7,8 the assumption is probably quite reasonable for most grains. Under a uniaxial tensile stress, ox, the work dW per unit volume expended in producing an increment of axial strain dex is, dW=oxdex [21 Since this work is expended in slip, dw =STi dyi 131 where Ti and yi are the shear stress and shear strain on the active slip systems. In both analyses Ti is taken to be the same on all slip systems, and dependent only on the total prior shear strain on all systems, so dw = Tdy [41 where t is the shear stress required for slip and y is the sum of the shear strain yi on all slip systems. Combining 121 and [4] and defining M = oX/T The ratio M is a generalized Schmid factor. It relates the tensile stress required for axially symmetric flow, ox, to the basic shear stress, 7, and it also expresses the ratio of crystallographic strain, y, to the tensile strain, Ex It depends only on the orientation of the crystal. Taylor evaluated M for various orientations by finding the least value of dy/dEx which could satisfy the shape change. Bishop and Hill, on the other hand, found M by considering the relative work (1/T)dW/dEx expended by stress states which could activate enough slip systems to produce the shape changes. The results of both methods appear to be equivalent, although certain omissions were made in Taylor's original work. The orientation dependence of M, calculated by the second method,9 is shown in Fig. 1. Taylor used the average 2= 3.06 for all possible orientations to predict the tensile stress-strain curve (oxvs Ex) for a random polycrystal from the shear stress-strain curve (t vs y) of a single crystal. Changes in M from lattice rotation were neglected so points on the ox vs ex curve were simply taken at ox = 3.06t and e = y/3.06 from corresponding points on the t vs y curve. Recent extension of the analyses of Taylor and of Bishop and Hill to crystallographically textured metals has been used to relate plastic anisotropy to textures, and to predict the potential texture hardening that could result from texture control.9 Unfortunately there have been relatively few experimental tests of the underlying theory. Taylor found that the tensile stress-strain curve of polycrystalline aluminum did agree reasonably well with that predicted from a single-crystal T-y curve. Had the single crystal undergone easy glide, how-

Jan 1, 1965

By Ralph H. Kress

Haulage trucks designed expressly for mine service were introduced about 35 years ago. The first models to arrive on the scene hauled about 15 tons and easily outperformed the modified highway trucks that had been used for mine haulage up to that time. The specialized trucks obviously had a greater potential for mining operations, and once this fact was recognized, competitive pressures in both the mining and truck-manufacturing industries drove the new vehicles toward ever more efficient performance. Many changes in truck design resulted, but not all were accepted for a variety of reasons. Often poor design was the reason, but in many cases progressive and promising designs were abandoned only because the truck manufacturer lacked the courage, tenacity, or vision to capitalize on them. There were also many cases where a promising new design was abandoned because the prototypes were initiated in a mine where personnel lacked the patience to prove them. Truck Startup Takes A Team Ally new truck that is to succeed and contribute to lower mine haulage costs must be well conceived and launched with good teamwork on the part of all concerned. Naturally, it is essential to have a good overall truck design at the outset to make this teamwork worthwhile. The design must include the selection of the right components manufactured by suppliers that can each do justice to their particular part of the new truck. Last, but by no means least, the mine operator where the truck is to be launched must be enthusiastic in his efforts to see the new vehicle through to successful operation.

Jan 1, 1971

By John W. Padan, Thomas E. Howard

Most of what has been written during the past few years on marine mineral resources has emphasized the vast potential of the ocean, and its floor, as a source of the vital mineral raw materials upon which our modern technological society depends. Computations have been made to demonstrate that the sea contains sufficient minerals to support any reasonable world population indefinitely. The importance of these resources from the standpoint of strengthening the national mineral resource base has been pointed out. And though the information upon which these conclusions are based is sketchy, essentially qualitative, and often conflicting, there can be no doubt that the mineral potential of the sea is tremendous and that there are compelling reasons for working toward its exploitation. Unfortunately, there has been little emphasis on the problems that must be overcome, from the perspective of the economics of mineral production. Some of these problems have been noted, and some authors have appraised them realistically. However, many proposed solutions have been more romantic than practical, from the standpoint of both technology and economics. As a result the general impression has been given, particularly to those uninitiated in the realities of mineral production, that the mineral wealth of the sea is there for the taking-requiring only a good modicum of courage and technologic innovation to place it within easy grasp. But developing the capability necessary for substantial, profitable production of sea bottom minerals will be far from easy. It will be accomplished much more quickly if the problems are faced squarely, defined properly, and attacked in an orderly, logical sequence. While this approach may lack glamour, it offers the highest probability for success.

Jan 6, 1966

It is too late to gloat over the fact that minerals have furnished 67 per cent of the primary wealth of Pennsylvania. It is high time that Pennsylvanians do some constructive thinking in terms of the present and future with regard to the remaining mineral heritage.1 The discovery of a deposit of pyrophyllite in the South Mountain region of the Cumberland Valley indeed emphasizes the increased importance of a more exact inventory of the metal and mineral resources of Pennsylvania. Active geological work and research have been in progress for many years, but the surface has been little more than scratched. The results obtained thus far in survey and research have been extremely beneficial to the Commonwealth and a fundamental hub of its industrial development. But these activities are wholly inadequate in the face of rising demands for the future. The need for an accelerated program to continue a study of Pennsylvania's mineral resources on a more intensive scale was never more acute.2 In part, this has been caused by the insatiable demands of industry. It has been caused also by wasteful use and ignorance.

Jan 1, 1950

By F. Weinberg

The relative concentration of 1" at grain boundaries in controlled orientation bicrystals has been examined by autoradiographic techniques, and by activity measurements of grain boundary surfaces exposed by preferential ,melting. The autoradio-graphs indicate that thallium is concentrated at grain boundaries in as-grown bicrystals, but not in zcell-annealed bicrystals. They also indicate that the solute concentration and the distribution on as-grown bicrystal surfaces are markedly different than that of the bulk material. The boundary surface measurements are in agreement with the autovadiographic evidence. On the basis of these measurements, as-grown bicrystals containing approximately 100 ppm of Tl, solidified at rates between 5 and 30 cm per hr and with tilt boundaries greater than 10 deg, exhibited grain boundary segregation equivalent to roughly 10 atomic planes of pure solute. Higher solute concentrations (equivalent to 140 atomic planes of pure solute) were obtained in bicrystals solidified slowly (0.6 cm per hr); slightly higher values were obtained in specimens containing a large angle nantilt boundary. Annealing for various times over a range of temperatures eliminated grain boundary segregation within the experimental uncertainty of the results (equivalent to 1 atomic Plane of pure thallium at the boundary). The results for the as-grown bicrystals can be qualitatively accounted for by assuming the presence of a groove on the solid-1iq;id interface, at the grain boundary. SOLUTE segregation at grain boundaries may be considered in two parts, namely, nonequilibrium segregation associated with the solidification process, and equilibrium segregation in fully annealed materials.' There is much indirect evidence for nonequilibrium segregation, based on preferential etching at grain boundaries and the mechanical properties of as-cast alloys. In addition, some direct observations have been reported in which radioactive tracers were used as solute additions and segregation detected at the grain boundaries by autoradiographic techniques. However, there is little detailed quantitative data on solute concentrations related to grain boundaries, particularly for different freezing conditions and grain boundary configurations. Equilibrium segregation at grain boundaries has been considered both theoretically and experimentally. cean' has made an estimate of the maximum equilibrium solute concentration that might be expected at a grain boundary, based on the lattice distortions in the boundary region. He arrived at a concentration which was equivalent t a monatomic layer of pure solute. A similar value, based on thermodynamic arguments, was calculated by Cahn and Hilliard for the segregation of phosphorus in iron. Experimentally, much higher values of solute concentration at grain boundaries have been reported recently by both Inman and iler' for phosphorus in iron, and Ainslie et 1.' for sulfur in iron. They observed concentrations equivalent to as much as 20 to 100 atomic layers of pure solute at the grain boundaries. However, in both cases it was shown that the observed segregation was not due solely to equilibrium segregation at the grain boundary. In the former case, precipitation effectss due to trace impurities in the material were believed to account for the large amount of solute present at the grain boundary. In the latter case it was shown that a high density of dislocations in the boundary region could provide a large number of additional sites for solute atoms, other than at the grain boundary. Thomas and chalmera have reported on the equilibrium segregation of po210 in grain boundaries of Pb-5 pct Bi alloys. Using autoradiographic techniques, they observed a concentration of polonium along the boundary trace on the surface of annealed bicrystal specimens grown from the melt. The concentration only appeared after annealing, and varied with boundary angle, increasing as the boundary angle increased. Their conclusions have been questioned by Ward," who pointed out that the segregation they observed along the boundary trace was much too wide to be compatible with the usual concepts of the thickness of a grain boundary of several lattice spacings. Also, Maroun et al.,l1 with specimens similar to those of Thomas and Chalmers, found that segregation could only be detected on the specimen surface, suggesting that Thomas and Chalmers' results were associated with an oxidation effect of polonium, and not equilibrium segregation. Thomas and Chalmers replied12 that they did observed segregation at the grain boundary in the bulk material and suggested further experiments were necessary to resolve the difference. The purpose of the present investigation was to examine both nonequilibrium and equilibrium grain boundary segregation in melt grown bicrystal specimens as a function of boundary angle, growth rate, and solute concentration, and to de-

Jan 1, 1963

Terminology Relating to Nonmetallic Elements in Metals. BY T D YENSEN AND C H HERTY, JR (Tech Pub 555, Metals Tech, June 6100 words ) The paper gives arguments for confining the term "gases in metals" to its proper sphere and recommends the name "nonmetallic elements in metals" as a general title of the subject dealing with: (1) nonmetallic elements introduced into metals unintentionally or for various specific purposes; (2) phenomena occurring in metals caused by non¬metallic elements It also recommends a classification of the subject in which "gases in metals" occupies a definite, logical place

Jan 1, 1935

By S. Ramachandran, R. G. Woolery

INTRODUCTION Union Carbide is currently operating an in-situ leach project on the Palangana Dome area in Duval county. This deposit meets all the requirements for in-situ leach in that the ore (1) is below the water table, (2) is in a permeable horizon, (3) is amenable to chemical leaching, and (4) is confined by impervious layers. This project has been under commercial production since 1976, and its capacity has been expanded on three occasions since going on-stream. Recently, additional uranium reserves were discovered on the Rogers-Cardenas (R-C) property about 32 km north of the Palangana operation. The ore is located within the Oakville sands and its characteristics are quite similar to those of the ore at Palangana. Both are an unconsolidated Arkosic sand high in clay and calcium carbonate. The R-C ore, however, is somewhat coarser with a mean particle size of 0.15 mm as compared to a mean particle size of 0.07 mm for the Palangana ore. In all respects it would appear that this ore would be a candidate for in-situ leach as a satellite operation to Palangana. Unfortunately, R-C ore is above the water table and, therefore, not amenable to the Palangana practice. Because of the limited known reserves in this deposit, it is readily apparent that conventional mining and milling are out of the question. However, because of its proximity to our Palangana operation, it seemed worthwhile to consider other options. The most viable route based on our past experience was to heap leach the ore. Our recent success at our Gas Hills facility and our Maybell operation, in employing a heap leach practice to our marginal reserves seemed to be a logical approach for processing this ore. Our experiences at both locations are described in "Heap Leaching - A Case History" by R. G. Woolery et al., Mining Engineering, March 1978. In both instances the process is an acid leach circuit and acid consumption averages 20 kg/t H2SO4. A preliminary feasibility study showed that because of the high strip ratio required for the R-C project to be successful, additional ore reserves must be located and that a method of heap leaching with an alkaline circuit would have to be developed. As a result of this paper study, the decision was made to proceed with a program of additional exploration drilling to determine the total ore reserves that could be mined economically. The Mining Department will evaluate each ore zone for cutoff grade, strip ratio, and expected mining cost. At the same time, a laboratory program to evaluate the available core samples for amenability to heap leaching with respect to an estimate of uranium recovery and processing costs was developed. This program is currently in progress, and at this time, we are just completing our process amenability study. BENCH-SCALE EVALUATION OF THE R-C ORE The initial bench-scale slurry leach tests on the R-C ore showed an acid consumption in excess of 200 kg/t H2SO4. These data, of course, discouraged us from considering this process route. Not only would the acid cost be prohibitive, but the gypsum generated by the reaction of the sulfuric acid with the calcium carbonate of the ore would severely effect the percolation of the lixivant. For this reason, the laboratory program was directed toward an alkaline circuit compatible with heap leaching. Because of the proximity of the R-C property to our Palangana operation, it seemed advisable to integrate the processing of this ore into the production at Palangana. Doing so would enable us to bring the R-C property into production by merely enlarging our present facilities at Palangana; otherwise, construction of a grass roots plant would be necessary. Ideally, the simplest method would be to construct the heaps at Palangana and employ an ammonium carbonate/bicarbonate leachant compatible with the in-situ production liquor. The product liquors could then be co-mingled or processed separately as desired. To determine if this goal was practical, samples of the R-C ore were obtained, and a laboratory program initiated. Heap leach amenability testing consisted of preliminary bench-scale evaluation to determine optimum solution strength and ultimate uranium recovery, followed by small column tests to confirm the bench-scale metallurgy and to determine percolation characteristics. These bench-scale tests are being followed by pilot-scale testing approximating field conditions. As expected, the bench-scale tests showed that the dissolution rate is considerably slower for alkaline leach than has been our experience in acid leaching. Because of the slower reaction rates, product liquor grades will be lower than for acid, as greater volumes of solution are required for satisfactory uranium extractions. The greatest influence on reaction times found in the laboratory was the carbonate/bicarbonate strength and oxidant addition. However, the higher salt concentration reduced the efficiency of the IX resin circuit and about 25g/L salt proved to an upper limit compatible with subsequent IX treatment. The oxidant contributed significantly to the early extraction rate but seemed to have only minimal effect on the total practical U308 extracted or the time required to achieve it. This variable will require larger scale testing to determine if the added cost of the oxidant is actually justifiable. Thus, the small-scale laboratory slurry tests, based on the 0.088% U308 sample available, indicate that leaching at 25g/L ammonium carbonate/bicarbonate, with or without oxidant, we might expect an 80-85% U308 extraction on this ore.

Jan 1, 1979

By J. J. Ormsbee

Attempts at coal-washing have been made in the southern states during the last twenty years; but it is only within the last four or five years that the practice has become at all general. It might perhaps be claimed as one of the blessings derived from our departed " booms;" for, during their sway, the supply of coal of all qualities, good and bad, could not equal the demand; but, with the subsidence of the inflated demand, came imperative calls for fuels of better quality; and washers, previously regarded as luxuries, became necessities. Among those now in use in this section are representatives of the following types or classes: the trough washer; the jig washer; the percussive table; and those washers in which a constant upward current of water effects the separation. Without having full statistics, it is safe to say that there are in successful operation in the South more washers of the last class than of any of the others. The purpose of these notes is to present data with regard to the constructiOn, operation, and results of one of these current-washers, based mainly on the plant at No. 2 Slope, Pratt Mines, Alabama. The coal is mined from the well-known Pratt seam, having here an average thickness of 3 feet 6 inches. It has distinct cleavage-planes, and breaks in cuboidal lumps; is bright black in color, firm in structure, and air-slacks only after considerable exposure. It burns freely, leaving a gray or buff-colored ash. The lump- and nut-coals are used for domestic and steampurposes (chiefly, however, for locomotive firing), and the slack for making coke. The specific gravity is 1.272. Analyses of Pratt Coal. I. 11. 111. IV. Min. Resources Authority. Phillips. McCalley. of U. s.,1892. Lupton. Fixed carbon,. . 67.90 61.600 64.30 63.82 Volatile material,.. 29.80 31.480 32.08 31.85 Moisture,.,...... 1.508 1.07 1.02 Ash,.... 2.30 5.416 2.08 3.31 Sulphur,. .. 0.83 0.918 0.47 0.70

Jan 1, 1896