Search Documents

By G. W. Doepel, W. P. Sibley

A three-dimensional, multilayer, mathematical model has been developed for predicting performance by mis-c.ible displacement. Areal and vertical coverage, total gas-oil ratio, propane-oil ratio and oil-recovery factor for the multilayer system are computed as functions of hydrocarbon pore volumes of solvent injected. The technique has been programed for use on the IBM-7090 digital computer and was used in calculating perfortnance for continuous miscible displacement of a five-spot, 50-layer .system. Results reported are based on the use of published laboratory data for a single, uniform five-spot layer. However, the technique is sufficiently generalized to calculate performance of any system of layers of any pattern configuration and mobility ratio, provided data are available to describe perfortilance of a single layer. The technique has also been adapted for predicting oil recovery resulting from various gas-driven slug sizes. The results presented for both continuous and slug-type injection show, that permeability variation has 0 significant effect on oil recovery but that solvent composition, within the range studied, has a lesser effect on oil recovery. INTRODUCTION Experience from many of the miscible-phase displacement projects currently in operation indicates that the injected solvent flows preferentially through the more permeable zones in the reservoir. This preferential solvent flow in the high-permeability streaks results in a reduction of vertical coverage (C,) and an attendant decrease in oil recovery. The multilayer technique presented in this paper uses areal coverage (C.,) data for a single layer from the literature and from laboratory measurements of displacement efficiency (herein referred to as microscopic coverage, C,,) to calculate areal coverage (C,) and vertical coverage (C,) for the multilayer system. Oil recovery for the multilayer system is obtained as the product of (Ca) (Cm) (Cv). It is assumed that C, in a single layer is 100 per cent; therefore, (C,) (Cm) is a measure of oil recovery from that layer. Data presented in the literature for a single layer generally deal only with areal coverage and/or microscopic coverage —but seldom specifically with oil recovery. Nevertheless, this technique is flexible in that either Ca and C,, of an individual layer or a direct measurement of oil recovery for the layer may be used. In developing this technique, the problem arose concerning a method of determining the relative amounts of solvent that will enter each layer during any increment of solvent injected. To solve the problem, a dimensionless equation was derived for expressing solvent injected into each layer as a fraction of total injection. A finite-difference method was applied in integrating the equation to determine oil recovery for the system of layers as a function of pore volumes injected. The technique subsequently was programed for solution on a digital computer. The method was applied to predict performance of a deep California reservoir under continuous miscible displacement and has been extended for calculating oil recovery as a function of slug size for gas-driven slug injection. The technique may be applied to any petroleum reservoir that can be adequately represented as a layered system, by considering permeability variation,1-3 permeability range and average permeability. Each layer is then assigned its appropriate permeability, porosity and hydrocarbon saturation. RESERVOIR VOLUME CONTACTED BY SOLVENT It has been recognized for some time that high microscopic coverage (C,) can be obtained by injecting a miscible agent, such as propane, into an oil reservoir. These high values of C,,, have been demonstrated in the laboratory and are normally between 80 and 100 per cent, depending on solvent and reservoir oil composition as well as on reservoir temperature and pressure. In miscible-phase displacement, because there is no interface between solvent and oil, effective permeability to solvent is the same as that to oil. (This assumes that oil saturation has not changed and that water is immobile.) Consequently, mobility ratio (M) simply reduces to that of viscosity ratio . Perrine4 and Habermann5 have shown that large

Report of the Secretary TO THE BOARD OF DIRECTORS OF THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS Gentlemen:-To a Board of Directors keeping in as close touch with all of the affairs under their care as do the Board of Directors of the A. I. M. E., through their monthly meetings, a report of the year's progress is almost superfluous. To the members who read the monthly reports of. the Board Meetings and of the various activities of the Institute as published each month, a yearly report cannot carry much fresh information; yet for both it may be well, as is the custom, to glance over the field of our activities during the past year, and to make an estimate for the year to come. The beginning of 1924 was not propitious for the members of the mining profession, though tonnage production for 1923 had been high and the gross value higher than for several years. The margin of profit had been narrow, prospecting and development were limited, and many of our members were unemployed, or were working in other industries. Toward the end of the year, higher metal, prices were in sight. Old-time optimism began to grow, and it now brightens the outlook for 1925. An excellent barometer of the prosperity of the industry, and that of the Institute, for they go hand in hand, is the work of our Employment Bureau. During the past few months, the percentage of our members for whom openings have been found has been increasing to a marked extent, and many members who had fallen in arrears are placing themselves in good standing. The number of new members joining has remained about as it was in 1922 and 1923. The Directors have reason to congratulate themselves on the interest maintained during a dull period, for it is not humanly possible to take a keen interest in the technology of an industry when our hands and minds are not actively engaged in it Now, with a much brighter outlook, we can look forward to a year of increasing prosperity for the industry and for the Institute.

Jan 3, 1925

By Edgar R. Kendall

A KNOWLEDGE of the fundamental principles of locating, sampling, testing and evaluating materials is essential in prospecting for mineral aggregates. In this discussion, mineral aggregates will be considered sand, gravel, crushed stone and slag that are used as materials of construction. The quantity of mineral aggregates produced in the United States during the year 1935 for such purposes was roughly 165,000,000 tons, about 60 per cent of which was sand and gravel, 37 per cent crushed stone and 3 per cent crushed slag. The total value of this material was approximately $100,000,000. It is apparent therefore that the prospecting for suitable mineral aggregates is of considerable economic importance. In prospecting for mineral aggregates, the methods employed are the same whether the organization is large or small. In the large organization there may be available geologists for locating sources of supply, a land acquisition department to arrange for the necessary options or permits, engineers to do the sampling, a laboratory for testing, and a board of consulting materials engineers to make the final selection. Even small organizations must follow the same general procedure, though the responsibility for the selection of aggregates may rest with one man, who may or may not be an engineer, but who must depend entirely upon his own judgment. LOCATING THE SUPPLY The initial step in prospecting for mineral aggregates is the locating of suitable, adequate and economic sources of supply for the project in mind. Commercial plants in the vicinity should be investigated and a survey made of the existing structures that have been built of aggregates from these sources. If the structures are rather old and show no signs of deterioration, it is fairly good evidence that the aggregate is satisfactory. If materials of the proper quality can be obtained from commercial sources in sufficient quantity, and delivered to the job economically, it

Jan 1, 1939

By A. R. T. Denues

LIQUID-OXYGEN explosives commonly consist of a carbonaceous absorbent enclosed in a canvas wrapper and soaked with a liquid containing more than 90 mol per cent of oxygen. Investigation of these explosives in this country was initiated in 1917 by George S. Rice, then Chief Mining Engineer of the Bureau of Mines. The early development is summarized in two papers.1,2 Their characteristics, advantages and disadvantages were considered in a recent bulletin of the Bureau of Mines.,3 Other publications of this Bureau4, 5 treat the technology of these explosives and contain adequate references to pertinent literature. These investigations defined the properties of liquid-oxygen explosives and improved them greatly; however, an outstanding disadvantage is their high inflammability, a property of critical practical importance. These explosives as hitherto prepared are easily inflamed; the combustion resulting from an accidental ignition is particularly dangerous because of the ease with which it passes into detonation. For this reason the Bureau of Mines undertook a cooperative investigation, which has resulted in the development of fire-retardant treatment for the minimization or elimination of this hazard without materially impairing the explosive properties, including the ease of detonation. This presentation will offer a general description of the investigation and the outstanding results. Further phases will appear in subsequent short papers, and the entire investigation including the results of detailed experiments will be available in a forthcoming bulletin of the Bureau of Mines (Bull. 429). The effects produced by fire-retardant treatments of the carbonaceous absorbent and of the canvas wrappers were investigated separately, and the efficacy of combinations of these treatments with particular reference to the possibility of inflammation and to the development of detonation from inflammation was studied. The experimental explosive was pre¬pared from a granular carbonaceous absorbent and. the results described maybe more or less unique for such a material. An extensive preliminary

Jan 1, 1940

By Brian J. Gorval, Robert L. Kemeny

INTRODUCTION Financing, or providing adequate capital at low cost for developing and bringing a natural resource property into production, is a fundamental requirement for profitable operation. Under the present economic environment the cost of financing any project is gaining more importance than ever. The fundamental keys for success in mining are "the Four M's": Mineral, Market, Management and Money. In recent years, with capital and operating costs skyrocketing, increased emphasis on obtaining adequate and low cost capital funds for bringing in a prospect is essential. For a small mining company there are limited sources for raising funds. In most cases these companies have neither a substantial asset base, nor any cash flow, and they are deemed as risky investments. The issue of shares of capital stock of such a company is probably the most common method of raising funds via the public purse. Alternatively, debt could be used and a source of such capital might be private investors or financial institutions. The company which intends to raise funds from the investing public by way of the sale of equity, subsequently lists those shares for trading on a stock exchange. Going and staying public commits a company to a multitude of complex laws, rules and reporting requirements. The governing bodies are the watch dogs for the public. The largest of such an organization of this kind in the world is the Securities and Exchange Commission (SEC) in the United States. In Canada, the Securities Laws come from within provincial jurisdiction. Most provinces have their own Securities Act, and Securities Commission. It is the Commission which administers the Act, and hence controls the distribution and trading of securities within the province. Extra provincial registration is required for trading and distribution in more than one province. In British Columbia, prior to a public offering, the approval of the Superintendent of Brokers (SOB) and of the VSE must be obtained. THE VANCOUVER AND TORONTO STOCK EXCHANGES There are five stock exchanges in Canada which supply a trading forum in which mining companies may operate. The stock exchanges are located in Montreal, Toronto, Winnipeg, Calgary, and Vancouver. Of the five stock exchanges, the Vancouver Stock Exchange (VSE) and the Toronto Stock Exchange (TSE) are the most heavily used for resource-based issues and are the focus of this paper. The objective of this section is to provide a brief background on the VSE and TSE. The Vancouver Stock Exchange The VSE is Canada's predominant stock exchange for financing resource-based, junior issues. Since 1907, the VSE has acted as a source of funds for mining, exploration and energy companies throughout Canada and the world. Currently, there are over 1400 companies listed on the VSE. During 1983, over 3.1 billion shares traded at a value exceeding CDN$3.96 million. The VSE has developed a reputation as one of the few exchanges where a speculative resource venture may obtain a listing and subsequent financing in a relatively short time, generally five to ten months. The SOB, the Investment Dealer's Association of Canada (IDA), and the VSE all regulate trading at the Exchange. Any irregularities in a company's stock dealings are investigated and trading may be halted by the VSE until a satisfactory explanation has been received from the suspended company. Companies can be suspended from trading or delisted for various reasons. One reason is misrepresentation of facts in documentation submitted to the SOB, VSE, or to the public, through news releases.

Jan 1, 1985

CORPORAL SHEPPARD B. GORDY Sheppard B. Gordy, a brief biography of whom was printed inn the January Bulletin, entered the employ of the Braden Copper Co. immediately on his graduation from the Sheffield Scientific School in 1912. He remained with this company four years, working up through the various grades to assistant foreman and foreman to one of the individual mines. The last year he was in its employ, he acted as general mine foreman. He was for a short time with the Chile Exploration Co. and then went with the Andes Exploration Co. (Anaconda) and remained with CORPORAL SHEPPARD B. GORDY. the latter, doing mine exploration and development work, until he sailed for home in June, 1918, to give a more personal and active service to his country in her need. He declined a tender of induction into an officers' training camp, at the urgent request of Professor McClelland supplemented by Mr. Potter, because they demonstrated to his satisfaction that he could give more valuable service to his country in helping out with the aircraft production. Being within the draft age, in order to carry out this plan, it was necessary for him to be called by his Local Board and sent to camp. This call came Aug. 26. Two weeks before that time lie had gone to Dayton, Ohio; to begin the study of aircraft production, and was sent by the Dayton Board to Camp Sherman, Chillicothe, Ohio, where he died of pneumonia on Oct. 9.

Jan 3, 1919

By J. M. Mutmansky, Y. J. Wang, H. L. Hartman

Procedures for determining the operating point that results when a fan is connected to a mine and placed in operation have been a source of confusion for decades. A variety of techniques have been proposed, often to the detriment of the practicing ventilation engineer trying to apply the techniques to the many mine/fan matching problems encountered in the engineering of mine ventilation systems. This paper proposes some different assumptions and definitions that simplify the problems in determining the operating point. As a result, a set of procedures is provided for determining the operating point of a mine/fan system when the outlet areas of the mine and fan are known. To simplify the development of procedures for determining the operating point for a mine/fan combination, the authors suggest that the mine pressures be redefined and then used in such a manner that the conservation of energy is ensured. This provides the basis for the recommendation that the fan operating point be determined using the fan total pressure and the system total pressure characteristics. This procedure can be applied to fans in the blower, booster, and exhaust positions equally well, and to both single-fan and multiple-fan networks. Another advantage is that the method is applicable to fans with or without an evase.

Jan 1, 1986

By K. E. Brown, G. H. Fancher

An 8,000-ft experimental field well was utilized to conduct flowing pressure gradient tests under conditions of continuous, multiphase flow through 2 3/8-in. OD tubing. The well was equipped with 10 gas-lift valves and 10 Maihak electronic pressure recorders, as well as instruments to accurately measure the surface pressure, temperature, volume of injected gas and fluid production. These tests were conducted for flow rates ranging from 75 to 936 B/D at various gas-liquid ratios from 105 to 9,433 scf/bbl. An expanding-orifice gas-lift valve allowed each flow rate to be produced with a range of controlled gas-liquid ratios. From these data an accurate pressure traverse has been constructed for various flow rates and for various gas-liquid ratios. A comparison of these tests to Poettmann and Carpenter's correlation indicates that deviations occur for certain ranges of flow rates and gas-liquid ratios. Numerous curves are presented illustrating the comparison of this correlation with the field data. Poettmann and Carpenter's correlation deviates some for low flow rates and, in particular, for gas-liquid ratios in excess of 3,000 scf/bbl. These deviations me believed to be mainly due to the friction-factor correlation. However, Poettmann and Carpenter's correlation gives excellent agreement in those ranges of higher density. This was as expected and predicted by Poettmann. He pointed out that their method was not intended to be extended to those ranges of low densities whereby an extreme reversal in curvature occurs.l As a result of these experimental tests, correlations using Poettmann and Carpenter's method were established between the friction factors and mass flow rates which are applicable for all gas-liquid ratios and flow rates. Definite changing flow patterns do not allow any one correlation to be accurate for all ranges of flow. INTRODUCTION The ability to analytically predict the pressure at any point in a flow string is essential in determining optimum production string dimensions and in the design of gas-lift installations. This information is also invaluable in predicting bottom-hole pressures in flowing wells. Although this problem is not new to industry, it has by no means been solved completely for all types of flow conditions. Versluys,2 Uren, et al, 3 Gosline,4 May,5 and Moore, et al,6,7 were all early investigators of multiphase flow through vertical conduits. However, all of these investigations and proposed methods were very limited as to their range of application. Likewise, many are extremely complicated and therefore not very useful in the field. Only in the last decade have any significant methods been proposed which are generally applicable. The most widely accepted procedure in industry at the present time is a semi-empirical method developed from an energy balance, proposed by Poettmann and Carpenter8 in 1952. Their correlation is based on actual pressure measurements from field wells. Accurate predictions from this correlation are limited to high flow rates and low gas-liquid ratios. Although this method will be discussed in detail later, it should be pointed out that two important parameters, namely the gas-liquid ratio and the viscosity, were omitted in their correlation. The viscosity was justifiably omitted since their data was in the highly turbulent flow region for both phases, and most wells fall in this category. The gas-liquid ratio was incorporated to some extent in the gas-density term. In 1954, Gilbert9 presented numerous pressure gradient curves obtained from field data for various flow rates and gas-liquid ratios for the determination of optimum flow strings. However, no method is presented for predicting pressure gradients except by comparison to these curves. Baxendell, et al,10 proposed a method based on Poettmann and Carpenter's procedure

By Henry A. Ley

Kansas ranked fourth on the list of oil-producing states during the year 1930. Progressive statistics show that total production for the year will approximate 42,729,085 bbl. When final figures are compiled for Kansas the production may exceed this estimate, and thereby threaten the all-time record of 43,253,470 bbl. in 1918. Throughout the year the cumulative volume of potential drilled-up production has been increased by new discoveries and by extensions to proven areas in the territory west of the Nemaha (granite ridge) Range. Scattered drilling and leasing operations of a constructive nature occurred, but completions declined to the lowest levels in more than 11 years. Average initial production of current completions climbed to a new all-time high of 512 bbl. to the well. Proration measures were applied to the flush pools. The resulting shut-in potential production, as of December 15, is estimated at 110,000 bbl. This estimate is a wild guess. If all wells of the state were permitted to flow wide open for a period of six months production would not exceed 150,000 bbl. a day. The outstanding development of the year was an intensive drilling campaign in southwestern Kansas, which contributed at least 1,000,000 acres of contiguous natural-gas lands to the natural-gas resources of the United States. Production and Development Prospecting for oil in Kansas began shortly after the initial prospecting at Titusville. Operations and interest in the potentialities became active about 1870. This development was restricted to the shallow districts of northeastern Kansas. By 1895 operations had extended southward to the Oklahoma state line and sufficient prospecting had taken place to prove the potentialities of the state. Active prospecting was extended westward by the discovery of oil on the Nemaha Range in Butler County about 1916. The discovery of oil in Russell County added an extensive borderland province in 1923. The important discoveries of oil in Sedgwick County revived interests and operations throughout this territory in 1928. The development of widespread natural-gas lands in extreme southwestern Kansas during 1930 carried active exploration to the western boundary of the state.

Jan 1, 1931

By Junichi Sato, Takash Suzuki, Tatsuo Imamura, Mamoru Hojo

INTRODUCTION Hitachi Refinery of Nippon Mining Co., Ltd. was constructed in 1911. The refinery began early to recover by-product metals and to manufacture copper products. Today, the refinery recovers gold, silver, selenium, platinum and palladium as by-products of the copper refining process and manufactures copper powder, copper foil, wire bars and chemicals for plating. In 1969, the capacity of the Hitachi Refinery reached 6,000 tons/month. (T/M). Because, at that time, the forecast was for the demand for copper in Japan to increase, planning for the expansion of the Hitachi and Saganoseki refineries was begun. A new 10,000 T/M capacity tank house, a new electrolyte purification plant and a enlarged anode slime treatment plant were planned for the Hitachi Refinery. Construction at the Hitachi Refinery began in December, 1970, and was completed in April, 1974. The development of new machines and processes has resulted in an efficient refinery with a production capacity of 16,000 TIM. This paper is a report on the new anode slime treatment plant at the Hitachi Refinery, and especially on the copper removal process in that plant, the Ferric Leaching Process.

Jan 1, 1976

By G. W. Tracy, R. D. Carter

A method based on an approach by Hurst' is developed for calculating water influx behavior. Using this method, superposition calculations may be eliminated. The principal diflerence between this method and that of Hurst is that, over finite intervals of time, constant oil-productton rates are assumed by Hurst whereas constant water influx rates are assumed in the presently described method. By adopting the assumption of constant water influx rate for finite time periods, a method is developed for calculating water influx behavior which lends itself to convenient combination with the material balance equation in the Schilthuis form. Above the bubble point, an equation is given for the explicit step-wise calculation of pressure history for a prescribed oil-production history. Use of this method of calculating water influx behavior should result in a considerable saving of time as compared to superposition calculations when the calculations must be made without using a digital computer. The connection is shown between the method described herein and the method developed by van Ever-dingen and Hursr2 (which requires superposition cal-culations). Also, results obtained using the two methods are compared.

By W. Scott Dunbar

INTRODUCTION Methods of linking boundary integral (BI) solutions with finite element (FE) solutions have been well described theoretically in other publications (e.g., Zienkiewicz, et al., 1977). The purpose of this paper is to point out some practical aspects of implementing these linkage algorithms for rock mechanics applications and to describe an alternative linkage algorithm. A not so obvious motivation for using FE-BI linkages is illustrated in Figure 1. The cost of modeling the excavation of the crusher station by the BI method can equal or exceed the cost of an equivalent FE model. This is due to the large surface area which must be modeled by the BI method. In such cases, a more economical approach might be to model the region immediately adjacent to the crusher station by finite elements and link the solution at the periphery of the FE model with a solution for the exterior region. Further economies can be realized if some flexibility in the type of exterior solution is possible. For example, it would be desirable to use a coarse discretization of the FE-BI interface for a BI solution, which would be less demanding of computer storage and time, or to use an analytical solution for the exterior region. The alternative linkage algorithm to be discussed allows such flexibility. BOUNDARY INTEGRAL METHODS There are basically two formulations of BI methods: the direct and the indirect. FE-BI linkage algorithms depend on which formulation is used. The purpose of this section is to briefly describe each method.

Jan 1, 1982

By R. E. Frounfelker, W. M. Hirthe

INVESTIGATORS in the areas of plasticity, crystal growth, and stress analysis have a need for crys-tallographic data such as the interplanar angles. This information is utilized in the form of a stereo-graphic projection from which orientation determinations can be made. Calculations of mechanical properties, such as the critical resolved shear stress, require values for the angles between directions as well as the interplanar angles. Only a limited amount of this data is available for tetragonal crystals. The equations for these angles are relatively simple but because of the large numbers of angles involved and the infinite number of structures that could be investigated, it was decided to program these calculations on a high speed digital computer. The angle, 8, between two crystal planes (h1 k1 l1)

Jan 1, 1962

By J. J. Knoerzer

A full-scale operational test was conducted on the Coaltek preheating and pipeline charging system at the Semet-Solvay Div. of Allied Chemical at Ironton, Ohio, for the purpose of determining whether a high-quality blast furnace coke could be made from blends containing at least 75% Illinois No. 6 Coal and at the same time reduce air pollution during the charging of the ovens. The coke produced had similar physical characteristics as compared to our conventional wet-charged coke, with the exception of smaller size for the preheat coke. Air pollution during charging was con- trolled and there were no serious operating problems. The coking time was reduced 25% from our normal 17 hr for wet charging to 12.8 hr for preheated charges. The blast furnace performance with preheat coke was satisfactory.

Jan 1, 1976

By D. L. Kelley

High-viscosity water injection has been proposed for use in reservoirs containing high-viscosity crude oils. Previous publications have largely ignored the possible effects of the connate water on the proposed process. This paper describes experimental work which indicates that the connate water will be forced ahead of the injected water to form a bank of low-viscosity water. This decreases the oil recovery which would be expected if such a bank were not formed. These effects are shown for a range of fluid mobilities and connate-water saturations for a five-spot injection system. In general, oil recoveries using viscous water are significantly greater than for untreated water even though they are less than would be expected if no connate water bank were formed. INTRODUCTION The effect of mobility ratio on the oil recovery of wa-terfloods has been known for many years. Muskat first pointed out that the fluid mobilities (k/µ) in the oil and water regions would affect the performance of the water-flood, and he estimated the general effect of these variables.' Since this early work, studies of the effect of mobility ratio on secondary recovery have been reported where mathematical,' potentiometric3 and scaled flow models' were used. These studies have shown that a reduction in the mobility ratio between the oil and the displacing fluid would cause additional oil recovery when water-flooding reservoirs containing viscous crude oils. Studies reported by Pye- nd Sandiford 8 have indicated that chemicals to increase injection water viscosity are now available and can be used to reduce the over-all mobility ratio of a waterflood. Where mobility ratios are controlled by the injection of viscous fluids, the connate water of the reservoir can play an important part in the displacement of the reservoir oil. The purpose of this study was to determine the effect of the connate-water saturation in waterfloods where viscous waters are used for injection. DISPLACEMENT OF THE CONNATE WATER Russell, Morgan and Muskat7 were the first to recognize the mobility of connate waters in waterflooding. They conducted waterfloods on oil-saturated cores containing 20 and 35 per cent irreducible water saturations, and found that from 80 to 90 per cent of the "irreducible" water was produced after only one pore volume of water was injected. However, their experiments were conducted at rates of flow significantly higher than those ordinarily occurring in waterfloods. Also, the cores were only from 4.0 to 8.5 cm long. Brown 4 studied a 100-cm linear sand pack which had been prepared to contain connate water and oil. He used 140- and 1.8-cp oils with injection water of essentially the same viscosity as the connate water. He found that all of the connate water was displaced by the injection water in both cases. However, the injection volumes required for complete displacement of the connate water were considerably higher in the case of the more viscous oil. To verify the results of the foregoing experiment, a 10-ft-long linear model was constructed by packing 250-300 mesh sand in a 1/2-in. diameter nylon tube. The model was evacuated, saturated with a brine of 1-cp viscosity, and flooded with a 41-cp mineral oil to the irreducible water saturation of 10.9 per cent. The model was then waterflooded by the injection of a water solution which had an apparent viscosity of 42.6 cp. The solution consisted of 0.5 per cent methylcellulose in distilled water. The viscosities of the oil and connate water were measured with an Ostwald viscosimeter. The viscosity of the polymer solution was calculated by Darcy's law using pressures measured during actual flow conditions. The ratio of the mobility in the oil region to the mobility in the inject ion-water region was approximately 0.32. The mobility ratio of the oil region to the connate-water bank was approximately 14. The mobility ratio between the connate-water bank and the injection water region was 0.024. Approximately 84.5 per cent of the recoverable oil was produced before water breakthrough. Immediately following breakthrough, oil and connate water were produced at an increasing water-oil ratio until the viscous injection water broke through. At viscous-water breakthrough, 96 per cent of the original connate water had been produced. After breakthrough of the viscous water, there was no additional production of connate water or oil. The near-

Jan 1, 1967

By A. E. Blakeslee

Morphological and electrical properties of GaAs epitaxial layers are influenced not only by changes in the nominal substrate orientation but also by small amounts of misorientation from the exact crystal planes. Deviations up to 5 deg from {11IA}, {11IB}, and (100) planes were investigated. Growth rates increase progressively with angle, approximately I u per hr per deg. Size and density of growth pyramids fall off with increasing angle, but other effects that are deleterious to the surface may occur which are heightened by increased misorientation. Carrier concentration decreases and electron mobility consequently increases as the angular offset increases, except in the case of strong compensation, where the mobility trend is reversed. It has long been known that changes in the crystallo-graphic orientation of the substrate may cause pronounced effects on the morphological properties of vapor grown semiconductor films. Reports of orienta-tion-dependent growth rates and surface characteristics are as old as the literature on epitaxy itself. shawl has recently published a comprehensive study of the dependence of growth rate on substrate temperature and orientation in epitaxial GaAs. It is also well-known that misorienting the substrate surface a few degrees away from the nominal low-index crystal-lographic plane often produces a much smoother epitaxial surface. This was reported by Tung2 for silicon, Reisman and Berkenblit3 for germanium, and by Kontrimas and Blakeslee4 for GaAs, and use is commonly made of this fact in the semiconductor industry to help guarantee smooth vapor deposits. The effects of substrate orientation on the carrier concentration and mobility of vapor grown GaAs were first documented by williams5 in 1964 and have been observed by several other authors since then,6,7 but no one has yet reported a careful study of how small changes influence these properties. We have made such a study and have found that sizable differences in growth rate, morphology, carrier concentration, and mobility can indeed be observed for epitaxial films grown on substrates that are oriented by progressive small increments away from the exact crystal plane. EXPERIMENTAL Early in the investigation an arsine synthesis system of conventional design8 was employed to produce growths on {111A}-oriented GaAs substrate crystals. In that early work, pronounced effects on carrier concentration and electron mobility were observed as a function of slight misorientation from this low index plane. That observation led to the more careful study that is reported here. An AsC13 system, differing in major aspect from those commonly in use today9 only in that the reactor is vertical rather than horizontal, was used for the detailed study. The gallium source was at 900°C and the substrates were at 750°C. The flow rate of pal-ladium-diffused H2 through the AsCl3 bubbler was 200 cu cm per min, and the flow rate of bypass H2 was also 200 cu cm per min. The substrates consisted of chro-mium-doped semiinsulating GaAs to facilitate elec-trical evaluation of the overgrowth by means of Hall and conductivity measurements on conventional eight-legged Hall bridges. They were misoriented by 0 to 5 deg from the {111A}, {111B}, and (100) planes, toward the (100) from the {111A} and {111B} and randomly toward the <111A> or <111B> from the {loo). The crystals were oriented for sawing by the Laue back-re-flection technique, which is good only to about ±1/2 deg; but after polishing or sometimes after epitaxial growth the wafers were checked by a diffractometer technique which is accurate to about * 0.1 deg. After lapping, the wafers were polished with NaOCl after the technique of Reisman and Rohr,10 and just before use they were cleaned in NaOC1, thoroughly rinsed with de-ionized water, and blown dry with nitrogen. Each run employed four wafers, each misoriented by differing amounts from one of the three major faces, and at least two runs were made for each orientation. The runs were continued long enough to provide at least a 15-µ or thicker layer. SURFACE MORPHOLOGY The appearance of all the films that were grown in a given run always changed from wafer to wafer as a function of increasing misorientation, but not always in the same regular fashion. At least three different trends were observed. These are more easily seen than described, and reference to the series of photo-

Jan 1, 1970

TO THE BOARD OF DIRECTORS OF THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS Gentlemen:-The following report covers briefly some of the more important activities of the Institute during the year 1923. In my report for the year 1922, I drew attention to the falling off in membership of the Institute due to the depressed condition of the mining industry in several lines and the inability of many of our members to find profitable employment in mining or its associated branches. A number who were unemployed during 1922 established connections during 1923, but a still greater number have been forced to resign or drop their membership during 1923. Fortunately, the number dropped is not so great as in the previous year. The Employment Service conducted by the four Founder Societies bears witness to the trend in business. For the young men just out of college, there are plenty of opportunities at small salaries, there are plenty of opportunities for them as laborers; but for the mature members, those of experience, there are few calls. During the last eighteen months, our Employment Service has been able to place only six of our members out of every hundred engineers for whom it has found work. Another loss which this Society has suffered, but which is not felt so keenly by our sister societies, is in its foreign members. The A. I. M. E. has always had a large foreign membership, but of recent years exchange has been so heavily against many European and South American countries that a large number of members residing abroad have been compelled to relinquish their membership. Almost invariably these members express keen regret because of the necessity that confronts them, and almost invariably the writers express hope that present conditions will not last long and that they will soon be able to ask-for reinstatement. Having stated the darkest side of the picture first, it may now be drawn to your attention that in spite of these losses the number of persons applying for membership was decidedly encouraging.

Jan 2, 1924

By Helmer Heldstrom

Gravity surveying with the torsion balance or the pendulum for ore prospecting purposes has generally not been considered practical or even possible. It is the intention of this paper to show that a fast and sensitive gravimeter can be very useful in ore prospecting, as an auxiliary to the electrical and magnetic instruments. A number of gravimeters have been constructed and put in practical use in the last seven or eight years; for instance, by Ising, Lejay-Holweck, Haalck, Hartley, Thyssen, Noergaard, the Humble Oil and Refining Co. and the Gulf Production Co. Their main application, apart from their use for geodetic surveys, has been for structure mapping in oil prospecting. There is no record that any of them have been used for ore prospecting. About the middle of 1934 the Boliden Mining Co., in Sweden, began experiments in constructing a static gravity meter sensitive enough for ore prospecting. Calculations and considerations that will be discussed later in this paper showed that this would necessitate an accuracy in the measurements of 0.1 milligal—roughly, one ten-millionth part of the total force of gravity. The first successful practical field tests of the instrument were made in January 1936. About the middle of 1937 the Boliden gravimeter was perfected. Ore prospecting with this instrument is now regular practice in Sweden, especially for the testing of indications given by geoelectric and magnetic methods. Gravity Anomalies that May Be Expected from Ore Bodies According to Newton&apos;s law, a mass M attracts the unit mass in a distance r with the force , GM where G = the gravitational constant = 6.68 . 10-8 c.g.s units. In the c.g.s., or centimeter-gram-second, system the force of attraction is expressed in the unit "dyne," which has the physical dimension c.g.s.-2 and denotes the force needed to accelerate the unit mass in one second to

Jan 1, 1940

By Helmer Heldstrom

Gravity surveying with the torsion balance or the pendulum for ore prospecting purposes has generally not been considered practical or even possible. It is the intention of this paper to show that a fast and sensitive gravimeter can be very useful in ore prospecting, as an auxiliary to the electrical and magnetic instruments. A number of gravimeters have been constructed and put in practical use in the last seven or eight years; for instance, by Ising, Lejay-Holweck, Haalck, Hartley, Thyssen, Noergaard, the Humble Oil and Refining Co. and the Gulf Production Co. Their main application, apart from their use for geodetic surveys, has been for structure mapping in oil prospecting. There is no record that any of them have been used for ore prospecting. About the middle of 1934 the Boliden Mining Co., in Sweden, began experiments in constructing a static gravity meter sensitive enough for ore prospecting. Calculations and considerations that will be discussed later in this paper showed that this would necessitate an accuracy in the measurements of 0.1 milligal—roughly, one ten-millionth part of the total force of gravity. The first successful practical field tests of the instrument were made in January 1936. About the middle of 1937 the Boliden gravimeter was perfected. Ore prospecting with this instrument is now regular practice in Sweden, especially for the testing of indications given by geoelectric and magnetic methods. Gravity Anomalies that May Be Expected from Ore Bodies According to Newton&apos;s law, a mass M attracts the unit mass in a distance r with the force , GM where G = the gravitational constant = 6.68 . 10-8 c.g.s units. In the c.g.s., or centimeter-gram-second, system the force of attraction is expressed in the unit "dyne," which has the physical dimension c.g.s.-2 and denotes the force needed to accelerate the unit mass in one second to

Jan 1, 1940

By Rollin A. Slater

This paper presents a composite of ideas on materials handling systems by describing the design of an over-all system for a hypothetical steel pellet plant located on the Great Lakes. The bulk materials handling industry has served for years as the skeleton and the central system of nerves and nourishment for the body of basic industries. During the past two decades, this body has undergone substantial growth and mutation to meet the surging demands of our national economy for more and better products. The steel industry has kept pace with spiralling demand by innovation which has resulted in new processes and improved designs which generally yield greater production from fewer units. Materials handling technology has likewise improved its techniques and currently has a new, stronger generation of equipment to perform its necessary supporting function. Drawing upon excerpts from several recent plant designs, this paper describes a basic approach to the selection and application of modern bulk materials handling systems to an entirely new steel plant. Specific details are not available for publication, and therefore the plant described herein is a composite of ideas. This imaginary plant will be located on the United States side of the Great Lakes and its owner will be called the Hypothetical Steel Corp. for purposes of discussion. TYPES OF EQUIPMENT The basic bulk materials handling systems and components required in a plant so situated are: lake boat unloaders; railroad train unloading systems; storage pile stackers and reclaimers; large bins and regulating feeders; and the conveyor systems — with their attendant controls— which connect the foregoing. PROGRAM OF DEVELOPMENT The initial work on the plant must be that of the process engineers who develop and refine the basic data, i.e., the logistics of all raw materials, waste materials and products within the plant. During this phase of study, the materials handling engineer may advance his planning only in basic areas such as movements at the dock and movements at the railroad. This initial planning work is concerned only with defining logical plant locations in the light of channels, currents, existing traffic, governmental regulations, locations of existing railroads and available rights-of-way. These systems alone have their own individual criteria which must be respected and accommodated in the final layout. All other elements, such as the arrangement of the blast furnaces, power house, coke plant, by-product plant, scrap preparation plant, BOF shop, and facilities for continuous casting, degassing, calcining, etc., are dictated by their own specific needs and their relation to each other. In the arrangement of these latter facilities, the materials handling system is secondary and must be designed to accommodate. BASIC LOGISTICS The result of the process engineer&apos;s work can be expressed in terms similar to those shown in Table I. Plants are customarily rated in terms of annual tons of ingots. Therefore, the basic size of this plant can be determined by referring to the BOF Shop wherein it is sized at 5 million tpy. From the base, the required hot metal can be traced to the blast furnace, which in turn indicates the amount of required flux, iron bearing materials and coke —which in turn establishes the demand for coal. Likewise, the total demand for flux can be determined by the combined demand of the lime plant and blast furnace. The generation of fines and waste products, which have significant value but are not usable as such, create the need for a sintering plant. From projections such as the foregoing, the complete flow of materials can be established and accommodated. The basic premise upon which this typical materials balance is predicted is that the plant will be a producer of high tonnages of non-SpecialtV- products. All basic raw materials (flux bearing, iron bearing, coal) will be prime quality. For example, the basic iron charge will be pellets, and the iron ore fraction will be sized lump, all of which

Jan 1, 1970