Search Documents

By P. Bardzil, J. Gurland

An experimental study of the variation of transverse-rupture strength with composition Anexperimentaland grain studysize has shown that the strength reaches a maximum for values of the mean free path between carbide particles of 0.3 to 0.6 microns. The fracture oforiginates in and proceeds through the carbide grains mainly. Impact strength and hardness also were recorded. MOST of the physical properties of sintered carbides vary linearly with composition. The transverse-rupture strength, however, shows a unique behavior. As the amount of binder metal is varied from 6 to 25 pct by weight, the strength at first increases; then, between 15 and 20 pct Co, it reaches a maximum of nearly 400,000 psi, and finally decreases with further additions of binder metal. This behavior of the transverse-rupture strength has been reported, among others, by Englel and Sandford and Trent.' The significance of these observations has not been discussed in the literature. That it may be of more than specific importance is indicated by the very similar variation of strength with composition encountered in other systems sintered in the presence of a liquid phase, such as Tic-Ni3 and Fe-Cu.' Experimental Details All compacts were prepared and sintered according to normal industrial practice. The average diameter of WC grains and the mean free path between grains were measured on metallographically prepared samples by a method of linear and planar analysis sing the relations where d is the average diameter of dispersed grains; Nl is the number of noncontiguous grains intersected on a metallographic plane by a line of unit length; N, is the number of noncontiguous grains per unit area; P is the mean free path between grains of dispersed phase; and f is the volume fraction of dispersed phase. Approximately 1000 grains were counted on each sample. For each composition d2 was plotted against P, the resulting straight lines serving as a check on the measurements. The distribution curves of the WC powders of different average diameters were homologous, and no attempt was made to influence the grain size by blending powders, adjusting the sintering conditions, or otherwise altering the particle size distribution. Densities were measured by differential weighings in air and water. The degree of densification did not vary consistently with either composition or grain size. The density is influenced by slight amounts of impurities, specifically by 0.1 to 0.2 pct Fe which enters the powders during ball milling. As an illus- -tration of the experimental variations, a number of measured densities are listed in Table I. They are expressed in percentage of theoretical density, as calculated from the published X-ray densities of WC and Co.' For the purpose of determining the transverse-rupture strength, rectangular test specimens (3/16x 3/8x3/4 in.) were broken by loading at the center of a 9/16 in. span. The average strength of five or more samples is reported for each composition and grain size. The compacts were ground on two parallel surfaces only. The load was applied at an average rate of 6,800 psi per sec. Since the elongation after fracture of the alloys is very small, it was assumed that the compacts deform elastically to failure and the fracture stress was calculated by the conventional beam formula. The data for one alloy are presented in Table II as an example of the results and scattering ranges encountered. The precision of the test, as measured by the average difference between duplicates, is of the order of 15,000 psi. The results are strictly comparable only to compacts prepared and tested in the manner described and of similar chemical composition and grain size characteristics. Unnotched Charpy specimens were used for impact testing. Each point represents the average of 3 to 20 samples, the larger number being used in an attempt to determine the influence of grain size. Considerable scatter was encountered, the range from lowest to highest value often amounting to 30 pct of the impact strength. The hardness is reported as a Ra reading, using a 60 kg load with diamond brale indenter. Compositions are given in weight percent.

Jan 1, 1956

Some years ago the open Hearth Committee of the Institute reached the conclusion that the reading of "set" papers tended to preclude the specific and detailed discussion of specialized problems of current interest to those operating steel plants. As an innovation the Committee distributed in advance of the meeting in May, 1927, a questionnaire containing a list of 27 topics involving operating problems. The subsequent discussion of the questions, participated in by 37 members, was a conspicuous success. Semiannual meetings have been held since; and at the conference of November, 1929, at Chicago, 131 men were present and the minutes comprised a book of 133 printed pages, thereby, indicating the growing value of the conference in the eyes of both the metallurgists themselves and the companies that employed them. With this example in mind, the Directors felt that definite advantages would accrue to a similar conference to be participated in by smelter officials and metallurgists engaged in the operation of copper reverberatory furnaces. The settlement of the Carson litigation, which for several years had virtually stopped public discussion of reverberatory practice, offered an opportune time for launching the scheme. Although the Conference may become largely self-financing in the future, some funds were regarded as necessary to conduct the first meeting. The members of the Rocky Mountain Income Committee, in view of the fact that copper smelting was essentially an activity of the Rocky Mountain area, recommended the project be, in effect, underwritten by the Fund, and the directors approved an appropriation for this purpose. Invitations were extended to high executives of the various-companies interested to send representatives to an initial meeting to be held at Salt Lake City, May 26-27. The response was enthusiastic. Twenty-three metallurgists representing 12 different plants were present to discuss the comprehensive-program relating to construction and operating phases of reverberatory smelting. It was understood that the record was not to be included in the regular publications of the Institute but that it would be prepared for private distribution among the participants and the officials of their companies. That the exchange of views and experience was no less instructive and stimulating than it was frank, full and informal is indicated by the following transcript of the minutes of the meeting.

Jan 1, 1930

By Albert Sir Kitson

THE manganese ore deposits of the Gold Coast, British West Africa, occur in very ancient rocks, of both sedimentary and metamorphic types. In. certain respects they strongly resemble those of India and Brazil, as contrasted with those of Tertiary age in Georgia. Viewed from the present condition of the maganiferous rocks, the oldest deposits are in the sediments. Later than these are the progressively metamorphosed representatives of these sediments; youngest are the products of decay and degradation with the concentration of manganese oxide of both areas. The oldest occurrences are in argillaceous and siliceous phyllites and slates, which show only a moderate amount of metamorphism. They belong to a series which also includes mudstones, sandstones, grits, conglomerates and subordinate limestones, with tuffs and lava-flows largely of basic types. To this series I have given the name Birrim. Its age is unknown, for no definite fossils have been discovered in it. As the characteristics of these non-fossiliferous strata at many places are the same as those of strata in many parts of the world that are suitable for the preservation of fossils and that contain them, it is assumed that the Gold Coast deposits are pre-Cambrian. These rocks of the Birrim series have normally a northeast-southwest strike and are folded, but not to any very great degree except in certain belts., From the Eastern Province of the Gold Coast they may be traversed across their strike for more than 600 miles to the extreme northwestern corner of the Northern Territories. Thence. they probably extend much further into French Territory.

Jan 5, 1927

By René de Batz

From 1754 to the end of 1895 the production of gold in Russia had been approximately as follows: Kilogrammes. Russia proper (Finland and the Caucasus),. .. 890 The Ural Region,........505,386 Western Siberia,........116,937 Eastern Siberia,........1,218,372 Total,.........1,841,085 of the value of more than $1,200,000,000.

Jan 1, 1899

By H. R. Steacy, A. H. Lang

Growth of general interest in uranium during the last ten years has been unparalleled in mining history, outranking the popular gold rushes and mining booms of bygone years. This is not surprising, considering the spectacular advances in nuclear research and the fact that a small amount of uranium can provide great quantities of energy for peaceful purposes. There are, however, a number of misconceptions and exaggerations regarding uranium. Many novices have highly exaggerated ideas of the ease of finding workable deposits, as opposed to mere occurrences, and reports of insignificant discoveries are sometimes given much publicity. Beginning about ten years ago mining for uranium has assumed a major place in Canadian and U. S. mineral industries. Uranium is now high on the list of metals produced in Canada. The gross value of uranium production in Canada in 1958, when additional plants now under construction are operating, will probably exceed 180 million dollars.

Jun 1, 1956

By Oscar Glaeser

THE mine and plant of the United Verde Copper Co., located in Yavapi County, at Jerome, Arizona, have been described in various technical publications and, therefore, a brief outline of its essential features will suffice. The orebodies are of the schist replacement type, the main sulfide mass being a large lens-shaped body approximately 7 acres in cross-sectional area. In general, the mineralization is found along the iron-schist contact, with the orebodies extending-about 1000 ft. along this contact and varying from a few feet to 250 ft. in width. The mine is located on a mountain slope and has openings into it on three horizons, as follows: 1. Raises and ore passes open vertically into the shovel pit. These extend down to the 1000-ft. level, where they terminate as loading bins in the Hopewell adit. The main fan intake air shaft, which also extends vertically down to the 1000-ft. level, has its surface opening on the hillside at the extreme north end of the shovel pit, and the main mine air return exhausts through a raise at the extreme south end of the shovel pit. 2. The 500-ft. level adit. 3. The Hopewell adit on the 1000-ft. level. The mine has a vertical downward extent of 2000 ft. below the 1000-ft. level. Underground operations are carried on through two main shafts, both of which are wholly underground. Shaft 5 is the ore-hoisting shaft. It has three compartments and extends from the 800 to the 3150-ft. level. Shaft 6 is the service shaft, and is used for lowering and hoisting men and material. It has a large cage compartment and three smaller compartments for counterweights, ladderway, and pipe and power lines. This shaft extends from the 500 to the 2550-ft. level, and is now being extended to the 3000-ft. level. An air shaft for the downward movement of fresh air from the fan has been provided, and extends to the 2550-ft. level at this time. Work has been started to extend this air shaft to the 3000-ft. level. A return airway for vitiated mine air, in the form of raises and short connecting drifts, extends downward to the 2100-ft. level.

Jan 1, 1929

By Walter Herd

FoR the past eight years No. 2 mine of the Cumberland Railway & Coal CO., Springhill, Nova Scotia—a subsidiary of the Dominion Coal Co., Ltd.—has had an unenviable reputation for bumps. As the workings extended in certain directions under a greater cover, these bumps increased in severity and it became apparent that some change in the system of extraction was necessary if the mine was to continue to operate. In September, 1924, following several fatalities resulting from bumps, the Mines Department of Nova Scotia requested from the U. S. Bureau of Mines the services of George S. Rice, Chief Mining Engineer of the Bureau, to report on the conditions then prevalent in No. 2 mine, Springhill. This request was promptly and courteously granted. Mr. Rice made a full investigation and a comprehensive and helpful report, which is embodied in the 1924 Annual Report of the Department of Public Works and Mines, Nova Scotia. Prior to 1925, the room and pillar method was employed and in January of that year (there being a cessation of work from March to August due to labor troubles) longwall retreating on the west side, on a limited scale, and in a small section on the east side of the mine was started. The major portion of the east side was not operated on this system till August, 1926, as there was developed a considerable area ready for pillar extraction between an arbitrary boundary and a point up to which bumps of any consequence had not been experienced. In the interval development work for longwall retreating below the 5900-ft. level was vigorously pushed. This longwall retreating system was suggested by Mr. Rice as a possible remedy and was heartily endorsed by the company officials. This paper describes the conditions and happenings subsequent to Mr. Rice's report and more especially the results with the longwall retreating system of mining under the peculiar circumstances pertaining to mining No. 2 Seam, Springhill, at depth, and records the conclusions which experience with several severe bumps under this mode of extraction would suggest. Except where necessary to make the paper intelligible as an entity any duplication of Mr. Rice's report will be avoided.

Jan 1, 1930

By Walter Herd

FOR the past eight years No. 2 mine of the Cumberland Railway & Coal Co., Springhill, Nova Scotia-a subsidiary of the Dominion Coal Co., Ltd.-has had an unenviable reputation for bumps. As the workings extended in certain directions under a greater cover, these bumps increased in severity and it became apparent that some change in the system of extraction was necessary if the mine was to continue to operate. In September, 1924, following several fatalities resulting from bumps, the Mines Department of Nova Scotia requested from the U. S.. Bureau of Mines the services of George S. Rice, Chief Mining Engineer of the Bureau, to report on the conditions then prevalent in No. 2 mine, Springhill. This request was promptly and courteously granted. Mr. Rice made a full investigation and a comprehensive and helpful report, which is embodied in the 1924 Annual Report of the Department of Public Works and Mines, Nova Scotia. Prior to 1925, the room and pillar method wasp employed and in January of that year (there being a cessation of work from March to August due to labor troubles) longwall retreating on the west side, on a limited scale, and in a small section on the east side of the mine was started. The major portion of the east side was not operated on this system till August, 1926, as there was developed a considerable area ready for pillar extraction between an arbitrary boundary and a point up to which bumps of any consequence had not been experienced. In the interval development work for longwall retreating below the 5900-ft. level was vigorously pushed. This longwall retreating system was suggested by Mr. Rice as a possible remedy and was heartily endorsed by the company officials. This paper describes the conditions and happenings subsequent to Mr. Rice's report and more especially the results with the longwall retreating system of mining under the peculiar circumstances pertaining to mining No. 2 Seam, Springhill, at depth, and records the conclusions which experience with several severe bumps under this mode of extraction would suggest. Except where necessary to make the paper intelligible as an entity any duplication of Mr. Rice's report will be avoided.

Jan 1, 1929

By C. R. Knopp

Gas-oil relative permeability ratio is an important relationship in oil reservoir predictive calculations. A correlation has been developed from 107 gas-flood k/k tests on Venezuelan core samples. The correlating parameter is based on restored-state water saturation tests and' is applicable to both consolidated and poorly consolidated sandstone reservoirs. Data of the correlation show that there are no distinguishah1e differences between the mass-data groupings for the two c1assifications A procedure is recommended for running .sufficient relative. permeability analyses to compute a geometric mean of the sample group. The geometric mean is more representative of the total core, and probably the entire reservoir. For example, while only one in four of the k,,/k,., test curves agreed closely with the resultant correlation of this report, the geometric mean curves of the 16 suites (three samples or more). showed good agreetment ill three cases out of four. INTRODUCTION The gas-oil relative permeability ratio is an important, fundamental relationship in most oil reservoir predictive calculations. Predictive calculations are made to estimate future reservoir production characteristics and ultimate oil recovery. The k1,/k2, relationship is specifically needed to relate the surface gas-oil ratio to the reservoir oil and gas saturation, and to calculate the relative movement of these phases within the reservoir whenever some of the more complex driving mechanisms are present. Laboratory k1/k2, tests are not generally run as a routine analysis. Consequently, k1/k2 data often are not available when needed because the cost of laboratory work could not be justified or the need for such data had not been properly anticipated. When laboratory k1/k2, data are available, they are often very difficult to interpret. For example, wide divergence is sometimes shown in a family of k1,/k1, tests representative of the producing horizon in a single well. With these considerations in mind, a study was made to determine if a relationship might exist between the k1,/k2, curve and some other simple laboratory test criteria. The most probable k1/k2, curve correlation for Venezuela described in this paper is the result of the investigation. The presented correlation defines the most probable gas-flood k,,/k,, curve through the medium of air-water capillary displacement and centrifuge water saturation tests. The laboratory procedures of these tests are. relatively simple, and inexpensive; test data should be. widely available- from routine analysis. DATA AVAILABLE, LABORATORY METHODS The report correlation utilized 107 gas-Hood k1/k2, tests run on sandstone cores of Venezuelan reservoirs. Table 1 is a general tabulation of data pertinent to the tests, while Table 2 summarizes the data. Thetests include 96 from Western Venezuela and 11 from Eastern Venezuela. Eighty-two- of the 107 test samples were sandstones that varied from poorly consolidated to-unconsolidated; 25 were consolidated. The average sample porosity was 26.7 per cent and the average permeability was 1,121 md; these values typify the better sandstone reservoirs of' Venezuela. The Welge gas-flood technique,' based on fundamental Buckley-Leverett frontal displacement theory, was introduced in about 1952 and is widely accepted in the industry. The laboratory procedure is relatively simple, rapid, and can be performed on small core samples. While there have been some minor variations in sample preparation and laboratory procedure in the tests used for the correlation, these tests can be generally summarized as follows. The core sample was first sol vent-extracted and dried. Connate-water saturation was restored by the oil-flushing or evaporation-blow down methods. At the beginning of gas flood the hydrocarbon pore volume was completeiy saturated with the test oil phase. Unsteady-state gas-oil displacement then began with the injection of nitrogen or helium. while the displaced oil and gas phases were incrementally metered at the out-flow face. From the test data, the k,,/k,, curve was calculated by the Welge method.' The individual oil and gas relative permeabilities were also calculated." CORRELATING PROCEDURES In attempting to establish a basis of correlation, we found that broad mid-range sections of 105 of the 107 k,,/k,, test curves could be closely duplicated by a straight line. Only two curves did not show a degree of linearity in this region. Correlation-curve definition parameters were subsequently developed from this observation of consistent mid-range linearity. Possible correlating variables were limited to the physical properties measured on core samples that (1) were widely available as common test data and (2) could be easily and cheaply obtained through future laboratory work. The more obvious possibilities were porosity, permeability and

Jan 1, 1966

By M. B. Ramachandra Roa

This paper records the results of the earth resistivity surveys made in the Godavari River in connection with the Ramapadasagar project. After describing the topographical and geological features of the area, the results of the investigation at the several sites have been mentioned. Further, a detailed account has been given of the resistivity methods adopted, the apparatus used and the interpretation of the curves. The resistivity measurements carried out over the water course have been specially outlined, and a review of the verification of the electrical indications by drilling in a number of cases, has also been presented. Introduction The Government of Madras has under consideration the Ramapadasagar project which is estimated to cost some Rs.660,-000,000 (about two hundred million dollars). The most essential feature of this project is the construction of a high dam across the Godavari near Polavaram for impounding the waters of this great river of South India, whose maximum discharge is 2 million cu secs in flood time. It is estimated that when the proposed reservoir is constructed, about one million tons of rice could be produced annually under irrigation. To those who have had any acquaintance at all with the recent distressing famine conditions which India has passed through and is still undergoing, the Lounteous effects which this project will bring about to the country in the future, are obvious. In the region of the proposed reservoir, the river flows for several miles through a hilly tract, hemmed in between flanks of hard, solid rock; but the river bed is mostly sandy. A few bore holes put down in this sandy bed touched rock at a depth of 180 to 200 ft. The river bed is about jo ft above the mean sea level (m.s.l.) and the bedrock was found at —125 to —160 ft m.s.l. The crest of the dam is proposed at +162 ft m.s.l. The proposed dam mould therefore be about 120 to 130 ft above the river bed, and the foundations would have to reach down nearly zoo ft below the bed at the deepest part. A number of alternative sites were proposed for investigation, and it became necessary to quickly ascertain the bedrock topography at these sites. Dr. M. S. Krishnan,* who was consulted in the matter, furnished a detailed account of the geological features of the region and suggested a geophysical investigation which the writer carried out from February to April 1944, employing solely the electrical resistivity methods. The total length of the survey lines for the electrical measurements amounted to 62,600 ft and the number of resistivity determinations was about 2500. Altogether nine alignments for the dam were inten-

Jan 1, 1949

By Sanford S. Cole

LABORATORY TESTS Takakuwa and Takamori' have applied the principle of phase inversion, well known in the chemistry of colloids, as a means of evaluating the wettability of minerals and to classify some frothing agents. By determining the angle of contact across the liquid phase of an emulsion, it has been possible to readily determine the wettability of a mineral. When this angle is less than 90°, the emulsion is of the oil-water type, and if it is greater than 90a, then the emulsion is of the water-oil type. The authors replaced oil with benzene in their recommended operation. They studied this method with the influence of ethyl xanthene on galena, on activated or unactivated zinc blend and of sodium cyanide on chalcopyrite and zinc blend. Raffinot and Formanek" described a pilot flotation plant with a capacity of 33 to 66 lb per hr of ore which is at the Laboratory of the Sociktk Minerais et Metaux in Paris. The plant will handle about 440 lb of ore per 8-hr shift and a regular series of tests can be undertaken with two to three tons of ore. Ore is ground to 0.1 in. and blended in advance. The plant includes two mills used either as rod mills or ball mills, conditioners, four groups of three cells for rougher circuits, eight cleaner cells and two small mills for regrinding middlings. Automatic controls for the pulp level in the cells, automatic sampling and addition of flotation reagents by electric valves facilitate plant operation and help to produce regular runs in spite of small throughputs.

Jan 8, 1963

By Fred P. Peters

T. D. Yensen.*—As my information is of a negative nature, I think it belongs under this paper. We are particularly interested in magnetic materials and we would like very much on occasions to make use of powder metallurgy. We have tried repeatedly to use powder metallurgy in preparing our nickel alloys but always. with negative results; that is, we cannot get as good magnetic properties by powder metallurgy as we can by starting with a molten material. We have tried by all possible means to make materials' like 50 per cent iron-nickel alloys by powder metallurgy. The compacts can be regularly lorged and rolled but no matter what we do in the way of annealing, the magnetic properties come out very much poorer than if we start with molten material. F. V. Lenel. †—I want to mention one characteristic of articles made from metal powders which distinguishes them from die castings; that is, their wear resistance. Die castings usually are made from zinc or aluminum alloys and a few copper-zinc alloys; all of them are comparatively soft and not very wear resistant. I know of a number of cases where powder metallurgy rather than the die-casting method was used for producing a certain part because higher wear resistance was needed than could be attained in die castings. A, J. LanghammeR.*—The subject of powder metallurgy is somewhat difficult to discuss, and portray, in the time that his been allotted. Most of you would rightly be bored if we went into details. However, I will cite one incident that possibly will help illustrate some of the potentials. Last summer I was in Washington and met Navy officials for the purpose of studying the possibility of making a certain part by powder metallurgy. The part is highly intricate and I happened to remark that the material cost would be high; that is, the cost on one raw material. Promptly a high-ranking Navy officer said: "Mr. Langhammer, if you must pay x dollars a pound for the raw material, but achieve the desired results, the cost of the finished part would still be low."

Jan 1, 1945

By Warren J. Jackson, John L. P. Campbell

Automatic recording of the radioactivity of the earth's formations provides a log of relative intensities that, if properly interpreted, can be applied to oil-field engineering. Production, engineering, and geological departments regard the radioactivity log as a forward step in the securing of more conclusive information for successful well completions. Explanations of the technique, together with some of the problems to which radioactivity logging have been applied, are presented in this paper. Introduction Those responsible for the completion of new oil and gas wells, or with planning workover operations on old wells, have followed closely the development of radioactivity well logging because they are interested in reducing the number of unknowns that usually are present in such work. Many operators have made use of the log, or are acquainted with at least one of the applications, but it is unlikely that any one operator is familiar with all of the many applications that are possible. The purpose of this paper is to present a representative example of each of the many applications, wherever the information has been released by an operator, and to illustrate by hypothetical examples other applications, releases for which have not been given. In this way, it is hoped that a better understanding of the scope of this new engineering tool may be obtained. Athough the literature contains many references that describe in detail the theory, development, and application of radioactivity well logging, a brief discussion of the technique may be helpful to those who are investigating the subject for the first time, All rocks contain radioactive material in varying concentrations. In general, shales contain relatively more radioactive material than sandstones or limestones. These radioactive materials disintegrate with time into other materials of lower atomic weight, and in that process of disintegration the rocks are emitting many rays, the most penetrating of which is the gamma ray. The intensity of emission of the gamma ray is proportional to the quantities of radioactive materials present. A higher rate of emission would be observed, therefore, opposite a shale than opposite a sandstone or limestone. Since measurable intensities of gamma rays are capable of penetrating as many as five concentric strings of casing, and as the gamma-ray intensity is relative to the formations, the measurements of variations in gamma-ray intensities offer a means of identifying cased-off formations in their proper stratigraphic sequence. TEe Gamma-ray Curve The measurement of gamma-ray intensi ties is accomplished by means of an ioniza-tion chamber that consists of a heavy cylinder, about 3 ft. long, that contains two insulated electrodes and is Med with an inert gas under high pressure. Under normal conditions no current will flow through the gas when an electrical potential is set up between the electrodes, but when

Jan 1, 1946

By Warren J. Jackson, John L. P. Campbell

Automatic recording of the radioactivity of the earth's formations provides a log of relative intensities that, if properly interpreted, can be applied to oil-field engineering. Production, engineering, and geological departments regard the radioactivity log as a forward step in the securing of more conclusive information for successful well completions. Explanations of the technique, together with some of the problems to which radioactivity logging have been applied, are presented in this paper. Introduction Those responsible for the completion of new oil and gas wells, or with planning workover operations on old wells, have followed closely the development of radioactivity well logging because they are interested in reducing the number of unknowns that usually are present in such work. Many operators have made use of the log, or are acquainted with at least one of the applications, but it is unlikely that any one operator is familiar with all of the many applications that are possible. The purpose of this paper is to present a representative example of each of the many applications, wherever the information has been released by an operator, and to illustrate by hypothetical examples other applications, releases for which have not been given. In this way, it is hoped that a better understanding of the scope of this new engineering tool may be obtained. Although the literature contains many references that describe in detail the theory, development, and application of radioactivity well logging, a brief discussion of the technique may be helpful to those who are investigating the subject for the first time. All rocks contain radioactive material in varying concentrations. In general, shales contain relatively more radioactive material than sandstones or limestones. These radioactive materials disintegrate with time into other materials of lower atomic weight, and in that process of disintegration the rocks are emitting many rays, the most penetrating of which is the gamma ray. The intensity of emission of the gamma ray is proportional to the quantities of radioactive materials present. A higher rate of emission would be observed, therefore, opposite a shale than opposite a sandstone or limestone. Since measurable intensities of gamma rays are capable of penetrating as many as five concentric strings of casing, and as the gamma-ray intensity is relative to the formations, the measurements of variations in gamma-ray intensities offer a means of identifying cased-off formations in their proper stratigraphic sequence. The Gamma-ray Curve The measurement of gamma-ray intensities is accomplished by means of an ioniza-tion chamber that consists of a heavy cylinder, about 3 ft. long, that contains two insulated electrodes and is filled with an inert gas under high pressure. Under normal conditions no current will flow through the gas when an electrical potential is set up between the electrodes, but when

Jan 1, 1946

By John L. P. Campbell, Warren J. Jackson

Automatic recording of the radioactivity of the earth's formations provides a log of relative intensities that, if properly interpreted, can be applied to oil-field engineering. Production, engineering, and geological departments regard the radioactivity log as a forward step in the securing of more conclusive information for successful well completions. Explanations of the technique, together with some of the problems to which radioactivity logging have been applied, are presented in this paper. Introduction Those responsible for the completion of new oil and gas wells, or with planning workover operations on old wells, have followed closely the development of radioactivity well logging because they are interested in reducing the number of unknowns that usually are present in such work. Many operators have made use of the log, or are acquainted with at least one of the applications, but it is unlikely that any one operator is familiar with all of the many applications that are possible. The purpose of this paper is to present a representative example of each of the many applications, wherever the information has been released by an operator, and to illustrate by hypothetical examples other applications, releases for which have not been given. In this way, it is hoped that a better understanding of the scope of this new engineering tool may be obtained. Although the literature contains many references that describe in detail the theory, development, and application of radioactivity well logging, a brief discussion of the technique may be helpful to those who are investigating the subject for the first time. All rocks contain radioactive material in varying concentrations. In general, shales contain relatively more radioactive material than sandstones or limestones. These radioactive materials disintegrate with time into other materials of lower atomic weight, and in that process of disintegration the rocks are emitting many rays, the most penetrating of which is the gamma ray. The intensity of emission of the gamma ray is proportional to the quantities of radioactive materials present. A higher rate of emission would be observed, therefore, opposite a shale than opposite a sandstone or limestone. Since measurable intensities of gamma rays are capable of penetrating as many as five concentric strings of casing, and as the gamma-ray intensity is relative to the formations, the measurements of variations in gamma-ray intensities offer a means of identifying cased-off formations in their proper stratigraphic sequence. The Gamma-ray Curve The measurement of gamma-ray intensities is accomplished by means of an ioniza-tion chamber that consists of a heavy cylinder, about 3 ft. long, that contains two insulated electrodes and is filled with an inert gas under high pressure. Under normal conditions no current will flow through the gas when an electrical potential is set up between the electrodes, but when

Jan 1, 1946

By John L. P. Campbell, Warren J. Jackson

Automatic recording of the radioactivity of the earth's formations provides a log of relative intensities that, if properly interpreted, can be applied to oil-field engineering. Production, engineering, and geological departments regard the radioactivity log as a forward step in the securing of more conclusive information for successful well completions. Explanations of the technique, together with some of the problems to which radioactivity logging have been applied, are presented in this paper. Introduction Those responsible for the completion of new oil and gas wells, or with planning workover operations on old wells, have followed closely the development of radioactivity well logging because they are interested in reducing the number of unknowns that usually are present in such work. Many operators have made use of the log, or are acquainted with at least one of the applications, but it is unlikely that any one operator is familiar with all of the many applications that are possible. The purpose of this paper is to present a representative example of each of the many applications, wherever the information has been released by an operator, and to illustrate by hypothetical examples other applications, releases for which have not been given. In this way, it is hoped that a better understanding of the scope of this new engineering tool may be obtained. Athough the literature contains many references that describe in detail the theory, development, and application of radioactivity well logging, a brief discussion of the technique may be helpful to those who are investigating the subject for the first time, All rocks contain radioactive material in varying concentrations. In general, shales contain relatively more radioactive material than sandstones or limestones. These radioactive materials disintegrate with time into other materials of lower atomic weight, and in that process of disintegration the rocks are emitting many rays, the most penetrating of which is the gamma ray. The intensity of emission of the gamma ray is proportional to the quantities of radioactive materials present. A higher rate of emission would be observed, therefore, opposite a shale than opposite a sandstone or limestone. Since measurable intensities of gamma rays are capable of penetrating as many as five concentric strings of casing, and as the gamma-ray intensity is relative to the formations, the measurements of variations in gamma-ray intensities offer a means of identifying cased-off formations in their proper stratigraphic sequence. TEe Gamma-ray Curve The measurement of gamma-ray intensi ties is accomplished by means of an ioniza-tion chamber that consists of a heavy cylinder, about 3 ft. long, that contains two insulated electrodes and is Med with an inert gas under high pressure. Under normal conditions no current will flow through the gas when an electrical potential is set up between the electrodes, but when

Jan 1, 1946

By R. E. Zimmerman

THE separation of fine sizes of coal from its impurities by means of various flotation methods has become of increasing importance in the coal industry. This, no doubt, will be even more so in the future as the quantity of high grade coal is depleted, particularly that used for metallurgical purposes. The purpose of this paper is to describe and report the results of research work done under the auspices of the Pittsburgh Coal Co. to determine the amenability of their bituminous fine sizes of coal to flotation, to investigate the value of various reagents and factors affecting their use, and compare the results between froth flotation and bulk oil flotation. Compared with the preferential flotation of complex minerals, or ores, the flotation of coal is comparatively easy. However, this statement should not lull one into the feeling that there are no special problems involved. For instance, the separation of coal from pyrite in high sulphur coals is still far from being 100 pct successful. Size consist has considerable effect on reagent consumption and recovery. Other factors will be described and finally it must be remembered that in the flotation of coal a low priced material is being treated and thus economic considerations govern more closely its application than is generally the case in treating other minerals. As a result of the research work done by the Pittsburgh Coal Co. on the flotation of coal, it was concluded that it was practical to clean the -48-mesh coal commercially by froth flotation and after several different types of flotation units and circuits were investigated by means of pilot plants, large scale units were installed at their Champion Nos. 1, 4 and 5 Preparation Plants for the cleaning of -48-mesh slurries. These large scale operations have been recently described by D. H. Davis. 1 C. P. Proctor and C. B. Carlson2 in their chapter on Froth Flotation of Coal in the AIME Seeley W. Mudd series book on Coal Preparation describe some of the practical applications of our Pittsburgh Coal Co. laboratory work in actual plant practice as well as summarizing part of the investigational work. The author presents this paper, however, as a supplement to their reports, and records the basic research accomplished in the laboratory investigational work as well as the results of experi¬ments using bulk oil flotation. In presenting this work the author wishes to state much more work must be done in applying the principles of flotation to cleaning coal, especially in view of recent studies and practices in other mineral beneficiation fields. METHODS OF CONDUCTING LABORATORY TESTS The bulk of the research work was conducted in the laboratory of the Champion No. r Preparation Plant. This plant has elaborate facilities for sampling and analyzing coal and proved to be an admirable location

Jan 1, 1948

Jan 1, 1968

By Craig R. Barrett

The influence of the stress dependence of the dislocation density on the overall stress dependence of The steady-state creep rate is discussed. Experimental measurements of dislocation densities and creep rates jor an Fe-3.1 pct Si alloy tested over a wide range of stress are presented which indicate a close correlation between the two quantities. EXPRESSING the stress dependence of high-temperature steady-state creep rates has been the subject of numerous investigations over the past decade. From these investigations have emerged a few general equations which fit most of the available data reasonably well. Garofalo 1 has proposed that for a wide range of stress and temperature the creep rate, i, can be expressed by a relationship of the form: where A, ß, and n are temperature-dependent and is the applied stress. Eq. [I] gives a stress dependence of a at low stresses and exp(nßo) at high stresses, both consistent with experimental observation where n = 5. A number of other investigatorshave proposed a similar expression where: where m and w are in general functions of temperature. Theoretical justification for Eqs. 111 and [2J comes from two different approaches, theories based on dislocation glide3-5 and theories based on the balance between work-hardening and recovery.' Dislocation glide theories predict where p is the mobile dislocation density and V is the activation volume. In order for Eq. [3] to predict a on stress dependence at low stresses with n = 5, it is necessary for p to be a strong function of stress, about proportional to u3 or u4.436 Recovery models of creep start with the general expression:' where r is the recovery rate and h is the work-hardening rate, and then employ a detailed model to determine the stress dependencies of r and h. As example, weertman2 has described a model based on pile-up hardening which results in an expression similar to Eq. [2] with m = 2 and p = 2.5. A recent, seemingly more general approach suggested by McLean is to use Friedels dislocation network growth expression to calculate the stress dependence of r. This model predicts r = p 3,2 and, as h is taken to be a relatively weak function of stress, the stress dependence of i should be about proportional to p3, 2. Once again, it is required that p be a strong function of stress to yield i This recovery model is by no means complete as the stress dependence of network growth is calculated in the absence of an applied stress meaning that r should probably be a stronger function of stress than given by p3, 2 and also some recent work by Mitra and McLean8 suggests that the stress dependence of h may be as large as Because of the importance of the stress dependence of p in determining the overall stress dependence of the strain rate it seems reasonable to examine this relationship in some detail. Measurements made on dislocation densities present during high-temperature steady-state creep generally obey the following relationship a =o0 + aGVWp [5] where uo is usually called a friction stress, a is a numerical constant about equal to unity, G is the shear modulus, and b is the Burgers vector. Depending on the magnitude of uo, data obeying Eq. [5] can give rise to a range of stress dependencies of p. For example, if we assume that the expression where 6 is some constant, adequately represents the stress dependence of p over a range of o, then from Although Eq. [6] obviously breaks down when u 5uo for uo 6 can vary over a wide range of values. In particular, if u > a, > 0 then 6 will be greater than 2. As an example the data of Ishida and McLean are plotted in Fig. 1 showing excellent agreement with dynes per sq cm) and also showing good agreement with a p cc u3 dependence when plotted on a log-log basis. As oo increases 6 tends to increase and correspondingly the stress dependence of the predicted creep rate should also increase,* as-

Jan 1, 1968

By G. Howell Clevenger

PAGE Introduction,............891 L Nature of Precipitates,.........892 11. Experimental Work Upon Alloys,......895 Silver,............895 Gold,............896 Conclusions,............896 111. Present Methods of Refining,.......897 1. Refining by Roasting,.........897 2 Refining with Acid,..........898 3. Smelting with Lead,.........902 Tavener's Method,..........903 Merrill a Method,.,........903 Comparison of Costs of Acid-Refining and Smelting Processes,. . 904 Detailed Costs of Refining Cyanide Precipitates at Lead, So. Dak., September 29, 1903,.........904 Cost of Acid-Refining at the Horseshoe Mill, Terry, So. Dak.,. . 907 IV. The Removal of Zinc by Distillation,.....908 Experimental Distillations,.....,...910 Analysis of Precipitates Used for Distillation-Experiments,. . 910 Discussion of the Results of the Distillation-Experiments,. . 915 V. General Conclusions,.........917 VI. Outline of a Proposed MEthod OF Treatment,.... 917 Introduction. Attempts to discover, for the cyanide process, a better precipitant than zinc have been unsuccessful. Hydrogen sulphide, sulphurous acid, ferrous sulphate, etc., precipitate gold and silver from cyanide solutions either not all or incompletely.

Jan 1, 1904