Search Documents

By J. D. MacKenzie

THE world production of copper for the first eight months of 1927 shows an increase of 3 per cent over the same period in 1926. Since February of this year, however, production has been considerably curtailed. The United States reduction in the last four months has been offset by the increased South Ameri-can and Belgian Congo production. The United States is now producing 58 per cent of the world production, Chile and Peru 17.3 per cent, Belgian Congo 5 per cent. In 1926 the United States produced 54 per cent, Chile and Peru 16.3 per cent, Belgian Congo 6.3 per cent. Production, Tons 1917-largest war year 1,580,000 1925 1,581,000 1926-increase 3 per cent 1,628,000 1927-increase 3 per cent 1,670,000 Copper Producing Countries, 8 mo., 1927: Tons Per Cent United States 644,000 58.0 Chile and Peru 192,000 17.3 Europe 90,000 8.1 Belgian Congo 56,000 5.0 Japan 46,000 4.1 Mexico 30,000 2.7 Canada 23,000 2.1 Figures are not available for Spain and Portugal, which would probably precede Mexico.

Jan 12, 1927

By Robert Bakish

VARIOUS aspects of structure-sensitive corrosion of single crystals and polycrystalline aggregates of Cu,Au have been presented in papers by the author, in association with W. D. Robertson. Prompted by some observations in the course of these studies, a new approach to the problem was undertaken. Results of these new experiments are reported here. Thin slices, less than 2 mm thick, were prepared from single crystals 3.5 mm in diam grown by the Bridgman technique. The crystals were homogen- ized for 300 hr at 850°C. Crystals with no deformation, crystals deformed in tension to the yield point, and crystals deformed 20 pct in excess of the yield point were used. Crystals of several different orientations were studied. Slices were immersed for one month in 2 pct aqueous solution of FeCl3 and, subsequent to this immersion, were subjected to bending. Immersion and bending were carried out at room temperature. The size and geometry of the crystals did not permit accurate data on the loads involved. A most unexpected result was obtained in the process of bending these slices of Cu3Au crystals normal to the (110) plane. Completely brittle be-

Jan 1, 1958

By Harrison Schmitt

IN the practice of ore finding the geologist is continually confronted with the question of oreshoot extension, so that the general problem seems worthy of systematic investigation. This problem appears when the reserves are estimated and when the advisability of deepening the shaft comes up. Moreover, there is need for lower development cost to keep pace with cost reductions in other departments, or even to offset a rising cost of ore finding or ore following. This can be gained by close geologic control of the development; and much of the geology involved is that bearing on the downward, upward, and horizontal extensions of shoots. Furthermore, the purchase of a mine or prospect often depends directly on the question of shoot extension; because it is seldom that the ore is fully developed and the purchase price is almost invariably based largely on "possible" and geologically prospective ore. Most current methods for estimating "possible" and the more nebulous classes of ore are crude and indecisive. In the following pages the extension of oreshoots is the major theme, although the more basic subject, the general art of ore finding, is given some space.

Jan 1, 1929

AT THE beginning of September, the French eased their pressure against Germany and allowed the latter to, be granted an arrangement for its reparation payments in kind according to the Lubersac-Stinnes agreement. The whole arrangement as to the German reparations is, however, but temporary. The Greeks suffered a disastrous defeat at the hands of the Turks in Anatolia, which rapidly resulted in the expulsion of the Greeks from Asia Minor, the Turks occupying Smyrna about Sept. 10. A few days after entering Smyrna the Turks sacked the city and finally set it afire, creating one of the most terrible destructions in history. At the same time their advance on Constantinople, together with their demands on the Allies, brought them directly in, con-flict with the latter and Great. Britain prepared for a new war, with doubt as to the support of France, whose political interests in the Near East are as different as their economic interests with respect to ;Germany. The Turkish situation became thus a threat against the peace of Europe. A revolution in Greece, followed by the abdication of King Constantine and the return of Venizelos to a function in the Government was one of the conse-quences of the defeat in Asia Minor. Civil war continued in Ireland, with more or less -bloodshed. Economically there has been no change for the better in Europe. In Great Britain there, are no signs of an -important trade revival. In Germany and Austria things are worse. French, Italian and Spanish affairs continue in a bad way. In the United States business is represented as "booming," but many people are inquiring where is the boom? About the middle of September Congress passed the tariff and the soldier bonus bills. The President signed the former and vetoed the latter, with a strong message that won praise among people who understand condi-tions. Congress tried to pass the bill over the veto, but failed. The President signed the tariff bill, which became effective Sept. 21. A severe handicap was thus imposed on American economics.

Jan 10, 1922

By Martin C. Kuhn, Lawrence G. Stevens, J. Mark Richardson

The majority of the world's known and anticipated reserves of nickel ores are lateritic deposits At present, there are several different process alternatives for recovering nickel and other desired metal values from laterite ores An overview is given of the selective reduction roast/ammoniacal leach process, one of the processes in commercial operation.

Jan 1, 1981

By J. R. Kyte, L. A. Rapoport, R. J. Stanclift, S. C. Stephan

Experimental studies covering a wide range of core materials and fluid properties have been conducted to determine the mechanism of oil displacement by water in a partially gas-saturated porous medium. In all instances, the presence of a gas phase was found to have a beneficial effect in reducing residual oil saturations. The practical significance of this benefit is discussed, and a simplified procedure is outlined for evaluating the effects of free gas on water flooding by means of short core tests. INTRODUCTION In addition to oil and water, reservoirs subjected to water flooding frequently contain, also, a gas phase. Common engineering procedures account for the presence of this "free gas" only from the viewpoint of volumetric balance, implying that the only role of the gas consists of providing "fill up" space. It is usually visualized that during the initial stages of the water invasion, the oil, moving ahead of the water, displaces part of the gas and that subsequently the remaining portion of the gas phase is totally compressed and dissolved in the advancing oil bank. Thus, consideration of a two-phase, water-oil flooding mechanism supplies an adequate basis for predictions of oil recovery if the pressure build-up caused by the flood is sufficiently great, so as to reduce the free gas saturation to a negligible value in any portion of the reservoir by the time that portion is reached by the advancing flood water. In many in- stances, however, waterflooding operations are carried out when the reservoir pressure is still relatively high SO that the pressure build-up associated with the water flood may not result in complete dissipation of the gas phase. Under such circumstances it is necessary to ascertain whether or not the presence of free gas has an effect on waterflood behavior and, if so, to account for any such effect in the evaluation of field operations. The difficulties encountered in attempting to arrive at a comprehensive picture of the displacement mechanism of oil by water in the presence of free gas stem from the fact that most of the published data on this subject were obtained under conditions that were either not clearly representative of those existing in a reservoir or not sufficiently controlled to permit evaluation of the effects specifically caused by the gas phase. Some of the most precise data found in the literature were obtained in tests using a "static" gas phase created prior to each water flood by circulating oil through partly gas-saturated cores until a "trapped," residual gas saturation was established throughout the system.' Other investigations were conducted under more representative conditions where the gas phase was free to move during the water flood: but in most cases the results of these tests were obscured by auxiliary phenomena which arise from the compressibility and solubility of the gas and preclude quantitative conclusions.2,3,4 Prior to water flooding, a reservoir usually contains oil and gas, distributed in a manner in which both are free to move. Thus, the principal objective of the present studies was to determine the type of displacement mechanism occurring when water invades a porous medium containing oil and a "mobile" gas phase. Further-

Jan 1, 1957

By A. H. Larson, T. P. McNulty

RECENTLY, an investigation of the absorption of sulfur dioxide gas in molten binary copper alloys was conducted. A Sieverts-type apparatus, consisting of a mercury-filled gas dispensing buret and a mercury manometer, was used initially for determining the volume of gas absorbed as a function of pressure. The equilibration behavior of the alloys studied indicated that the mercury in the gas measuring system was absorbing sulfur dioxide. Owing to the widespread use of mercury as a displacement medium in absorption studies, an investigation was made to determine the nature and magnitude of the mercury - sulfur dioxide absorption effect. The gas measuring system was modified by substituting a Worden Quartz Products Type PDHV fused-quartz-spiral pressure gage for the mercury-filled dispenser and manometer. The dispensed gas volume at known temperature and atmospheric pressure was measured by evacuating a Pyrex vessel of known volume and by admitting sulfur dioxide into the vessel until the attached quartz pressure gage registered atmospheric pressure. Atmospheric pressure was measured concurrently with a separate mercury barometer. The volume of the empty sample chamber and its attendant apparatus was determined by measuring the equilibrium pressure accompanying the addition of a measured volume of sulfur dioxide into the initially evacuated system. The volume of the mercury sample was calculated from the density of mercury at the temperature of the study (25°C). Measured volumes of sulfur dioxide were then dispensed into the system and the equilibrium pressure accompanying each gas addition was determined. From the difference between the system volume and the mercury volume, the number of moles of gaseous sulfur dioxide remaining in the system at each pressure was calculated. The difference between the number of moles of gas dispensed into the system, denoted Enso2: and the number of moles of gas remaining in the system after absorption equilibrium had been attained, denoted nso2(g), was equal to the number of moles of absorbed gas, denoted nSO2. The number of moles of absorbed gas was then converted to absorbed volume, denoted VSo2, in cu cm at stp conditions of (PC and 760 mm Hg. Table I contains calculated values of Snso2, nSo2(g), and VSo2 for different sulfur dioxide pressures. In the original system, denoted Run I, volume limitations of the gas dispensing system prevented absorption studies at equilibrium pressures near atmospheric pressure, so a different gas dispensing system, denoted Run 11, was used for determining the last pressure reading in Table I. The data in Table I are expressed in terms of the absorption of sulfur dioxide in 49.68 cu cm of mercury. In Fig. 1, these data are expressed in terms of the absorption of sulfur dioxide in 100 cu cm of mercury. Since the absorption data plotted in Fig. 1 show a linear relationship, the volume of sulfur dioxide absorbed in mercury is a function of the first power of pressure. The absorption reaction is So2(gas) = SO2 (in Hg) The first-power pressure dependence, coupled with the fact that the sulfur dioxide could be removed from the mercury by applying vacuum, indicated reversible

Jan 1, 1967

Procurement of uranium is vital to the future of the Nation. Its utilization for atomic energy can destroy mankind or raise an unsurpassable civilization-the problem of the statesmen. Uranium poses a challenge to the mining profession. Evanescent in occurrence, its discovery and mining can mean substantial profits, plus safeguarding the future of the Nation.

Jan 9, 1951

By W.W. Weigel

The mines of the St. Joseph Lead Co. in St. Francois County, Missouri, form a roughly triangular area of about 45 square miles. Locally this is known as the Lead Belt. The four operating mines in the area at present are the Federal, Leadwood, Desloge, and Bonne Terre, in decreasing order of mine area and daily production. Mining began in 1864 and has been carried on in the district continuously since that time. As a group, the Lead Belt mines now handle 20,000 gal. per min. of water, average head about 465 ft., against a normal daily ore tonnage of 21,200 tons. For a six-day operating week this gives a ratio of 6½ tons of water per ton of ore. Total average pumping in 1931 was about 15,000 gal. per min. Since that time a large area of virgin territory has been opened, much of which has had temporary flush flows. About 75 per cent of the water enters in certain restricted very wet areas. Production figures are given in Table I. The figures by divisions for 1931 and 1941 are not exactly comparable, as there were several transfers of pumping loads from one division to another during that period of time. Geology The, basement formation in 'the Lead Belt area consists of the pre-Cambrian rhyolite porphyry and granite. Overlying this is the La Motte sandstone, of Middle Cambrian age, which offers a good medium for circulation of water. It varies in thickness up to 400 ft. Above this is the Bonne Terre dolomite, approximately 375 fl. thick, which in turn is overlain by the 150-ft. Davis shale. The formations above this, present in the Lead Belt in small areas only, are of minor importance. The ore bodies occur as large, horizontal tabular masses or as long, narrow runs; they are found throughout the Bonne Terre but largely in the lower 150 ft. The rather indefinite contact with the La Motte is a favorite ore horizon. Milling is entirely by open stope and pillar breast systems. To the south, west, and north of the district, sandstone outcrops are few and limited. Heavy faulting bounds The district on those sides and probably there is little if any artesian circulation from those directions. To the east, the La Motte rises to an outcrop area of about 40 square

Jan 1, 1943

By Olav Klomstadlien

The lean, but extensive iron ore deposits of the Dunderland Valley north of Mo i Rana, Norway, are the raw material base for Rana Mines, a division of the state-owned A/S Norsk Jernverk steel mill. The iron bearing minerals are magnetite and specular hematite. The magnetite/hematite ratio varies considerably both within each deposit and from one deposit to another. The ore bodies that lend themselves to mining have generally a thickness of 30-60 m grading 30-35% Fe and 0.15-0.25% P. The grain size varies from 0.05 to 2.5 mm. The fine grained ores are hard while the coarse grained ores are soft and easy to grind. The A/S Norsk Jernverk steel mill operates both a sinter and a pellet plant, and this necessitates production of two types of concentrates. The present flowsheet is shown in [Fig. 1]. The crude ore from the pits is crushed in a 1.07-m gyratory crusher with an open side setting of 12.7 cm. The crusher product is transported by rail to the concentrator located 25 km from the mines. The ore is fed by twelve 1.22 X 1.83 m vibratory feeders onto conveyor belts which carry the ore to a surge bin ahead of the autogenous mills. The feed rate is automatically adjusted to maintain a set power load at a level suitable for the ore type being processed. The mills operate in closed circuit with twelve dual-drum screens equipped with a 0.8-mm screen cloth. Oversize is returned by gravity to the mill feed while undersize flows to the gravity separation section which consists of Humphrey spirals in three stages. The ores are very heterogenous and analysis may vary quite considerably. The quantitative need for concentrate in the steel mill may also change rapidly. The process in the concentrator must therefore be easily changed, and consequently alternative process lines have been established. This is indicated with the dotted lines in the flowsheet. Apatite is removed by flotation by fatty acids to give a final sinter concentrate of 63% Fe and 0.020% P or less. Pellet concentrate contains about 65% Fe and less than 0.020% P. The fineness is about 1500 Blain.

Jan 1, 1981

By W. W. Weigel

THE mines of the St. Joseph Lead Co. in St. Francois County, Missouri, form a roughly triangular area of about 45 square miles. Locally this is known as the Lead Belt. The four operating mines in the area at present are the Federal, Leadwood, Desloge, and Bonne Terre, in decreasing order of mine area and daily production. Mining began in 1864 and has been carried on in the district continuously since that time. [ ] As a group, the Lead Belt mines now handle 20,000 gal. per min. of water, average head about 465 ft., against a normal daily ore tonnage of 21,200 tons. For a six-day operating week this gives a ratio of 6 ½ tons of water per ton of ore. Total average pumping in 1931 was about 15,000 gal. per min. Since that time a large area of virgin territory has been opened, much of which has had temporary flush flows. About 75 per cent of the water enters in certain restricted very wet areas. Production figures are given in Table I. The figures by divisions for 1931 and 1941 are not exactly comparable, as there were several transfers of pumping loads from one division to another during that period of time. GEOLOGY The basement formation in the Lead Belt area consists of the pre-Cambrian rhyolite porphyry and granite. Overlying this is the La Motte sandstone, of Middle Cambrian age, which offers a good medium for circulation of water. It varies in thickness up to 400 ft. Above this is the Bonne Terre dolomite, approximately 375 ft. thick, which in turn is overlain by the 150-ft. Davis shale. The formations above this, present in the Lead Belt in small areas only, are of minor importance. The ore bodies occur as large, horizontal tabular masses or as long, narrow runs; they are found throughout the Bonne Terre but largely in the lower 150 ft. The rather indefinite contact with the La Motte is a favorite ore horizon. Mining is entirely by open stope and pillar breast systems. To the south, west, and north of the district, sandstone outcrops are few and limited. Heavy faulting bounds the district on those sides and probably there is little if any artesian circulation from those directions. To the east, the La Motte rises to an outcrop area of about 40 square

Jan 1, 1943

By W. W. Weigel

The mines of the St. Joseph Lead Co. in St. Francois County, Missouri, form a roughly triangular area of about 45 square miles. Locally this is known as the Lead Belt. The four operating mines in the area at present are the Federal, Leadwood, Desloge, and Bonne Terre, in decreasing order of mine area and daily production. Mining began in 1864 and has been carried on in the district continuously since that time. As a group, the Lead Belt mines now handle 20,000 gal. per min. of water, average head about 465 ft., against a normal daily ore tonnage of 21,200 tons. For a six-day operating week this gives a ratio of 6½ tons of water per ton of ore. Total average pumping in 1931 was about 15,000 gal. per min. Since that time a large area of virgin territory has been opened, much of which has had temporary flush flows. About 75 per cent of the water enters in certain restricted very wet areas. Production figures are given in Table I. The figures by divisions for 1931 and 1941 are not exactly comparable, as there were several transfers of pumping loads from one division to another during that period of time. Geology The, basement formation in 'the Lead Belt area consists of the pre-Cambrian rhyolite porphyry and granite. Overlying this is the La Motte sandstone, of Middle Cambrian age, which offers a good medium for circulation of water. It varies in thickness up to 400 ft. Above this is the Bonne Terre dolomite, approximately 375 fl. thick, which in turn is overlain by the 150-ft. Davis shale. The formations above this, present in the Lead Belt in small areas only, are of minor importance. The ore bodies occur as large, horizontal tabular masses or as long, narrow runs; they are found throughout the Bonne Terre but largely in the lower 150 ft. The rather indefinite contact with the La Motte is a favorite ore horizon. Milling is entirely by open stope and pillar breast systems. To the south, west, and north of the district, sandstone outcrops are few and limited. Heavy faulting bounds The district on those sides and probably there is little if any artesian circulation from those directions. To the east, the La Motte rises to an outcrop area of about 40 square

Jan 1, 1943

Texture Transition in Ordered CuAu, by E. A. Starke, Jr., J. C. Ogle, and C. J. Sparks, Jr., Trans. TMS-AIME, 1969, vol. 245, pp. 169-70. pole figures should have had two parts not one. On the Estimation of Oxygen Absorption by Continuous Molten Metal Streams, by J. Szekely, Trans. TMS-AIME, 1969, vol. 245, pp. 341-44.

Jan 1, 1970

By J. R. Low, M. Gensamer

During the course of an investigation into the drawability of automobile-body sheet steel, it became apparent that certain advantages would be possessed by a deep-drawing steel with a very low yield strength, but almost normal tensile strength, provided a reduction in yield strength could be accomplished without sacrifice of ductility and fine grain size. It would also be desirable to have this steel free from strain-aging; that is, free from the tendency for the yield point to return after it had been eliminated by straining. It was known that, wet hydrogen treatment acted to eliminate aging, but as carried out by other investigators, at relatively high temperatures, this treatment resulted in grain coarsening. It has been established by some of the experiments reported in this paper that all of these objectives can be accomplished by treatment in wet hydrogen at a low temperature, in the neighborhood of 72o°C. The time of treatment is relatively short (about 3 hr, to completion with 20-gauge sheet) if the water content of the hydrogen atmosphere is made fairly high, say aimost 30 per cent by volume. At this temperature. the grain size remains fine in the time required. After this treatment sheet reduced the usual amount by cold-rolling has a grain size of about A.S.T.M. No. 7. The yield point is completely eliminated, and the yield strength is reduced to a very low value, in the neighborhood of 15,000 lb. per sq. in. The stress-strain curve departs gradually from the straight-line elastic part after the fashion of nonferrous deep-drawing alloys. This elimination of the yield point is accompanied by a verv low indentation hardness; for example, 32 Rockwell B or even lower. There is no aging as measured by increase in the yield strength upon aging at room temperature or for 3 hr. at 200°C., after stretching about 10 per cent in tension. Tensile strength is only slightly less than the box-annealed sheet, seldom dropping much below 40,-ooo lb. per sq. in. Elongation is practically unchanged, or increased slightly. The term yield point, as here used, refers to the phenomenon of heterogeneous deformation occurring at a substantiallv constant load, observed principally in annealed low-carbon steels. If such a steel is loaded in tension, the load increases steadily with elastic strain, suddenly falls, fluctuates slightly about some constant value for a time and then begins to rise again as deformation proceeds. The maximum initial load before the sudden drop is generally called the "upper yield point"; the value of the load where deformation proceeds at a

Jan 1, 1944

By J. R. Low, M. Gensamer

During the course of an investigation into the drawability of automobile-body sheet steel, it became apparent that certain advantages would be possessed by a deep-drawing steel with a very low yield strength, but almost normal tensile strength, provided a reduction in yield strength could be accomplished without sacrifice of ductility and fine grain size. It would also be desirable to have this steel free from strain-aging; that is, free from the tendency for the yield point to return after it had been eliminated by straining. It was known that, wet hydrogen treatment acted to eliminate aging, but as carried out by other investigators, at relatively high temperatures, this treatment resulted in grain coarsening. It has been established by some of the experiments reported in this paper that all of these objectives can be accomplished by treatment in wet hydrogen at a low temperature, in the neighborhood of 72o°C. The time of treatment is relatively short (about 3 hr, to completion with 20-gauge sheet) if the water content of the hydrogen atmosphere is made fairly high, say aimost 30 per cent by volume. At this temperature. the grain size remains fine in the time required. After this treatment sheet reduced the usual amount by cold-rolling has a grain size of about A.S.T.M. No. 7. The yield point is completely eliminated, and the yield strength is reduced to a very low value, in the neighborhood of 15,000 lb. per sq. in. The stress-strain curve departs gradually from the straight-line elastic part after the fashion of nonferrous deep-drawing alloys. This elimination of the yield point is accompanied by a verv low indentation hardness; for example, 32 Rockwell B or even lower. There is no aging as measured by increase in the yield strength upon aging at room temperature or for 3 hr. at 200°C., after stretching about 10 per cent in tension. Tensile strength is only slightly less than the box-annealed sheet, seldom dropping much below 40,-ooo lb. per sq. in. Elongation is practically unchanged, or increased slightly. The term yield point, as here used, refers to the phenomenon of heterogeneous deformation occurring at a substantiallv constant load, observed principally in annealed low-carbon steels. If such a steel is loaded in tension, the load increases steadily with elastic strain, suddenly falls, fluctuates slightly about some constant value for a time and then begins to rise again as deformation proceeds. The maximum initial load before the sudden drop is generally called the "upper yield point"; the value of the load where deformation proceeds at a

Jan 1, 1944

By W. C. Peters

From the time of its beginning in the mid-19th century, the American barite industry has had its major development in the eastern and central states. Geologic and economic factors serve to maintain Arkansas, Missouri, and the Southern Appalachian states in the lead position. In earlier days, the major markets for barite were in paint, chemical, and glass manufacturing, and the favored deposits were those which were close to eastern industrial areas; furthermore, the eastern deposits were cheaply mined and required little or no beneficiation. In the last few decades, the use of barite as a weighting medium for muds in rotary oil well drilling has caused a great expansion in the industry, but the marketing picture is still centered outside of the western states-now on the Gulf Coast area where high pressures are common in oil wells. Low cost imported barite, readily available on the East Coast and Gulf Coast, has always been a major marketing factor in the industry. The major barite producing state is Arkansas, with the industry centering about the Magnet Cove area. Missouri ranks second, with production mainly from residual deposits. Several Southestern states are actively producing from residual deposits.

Jan 9, 1958

By AIME AIME

A CORPORATION would go into bankruptcy if its affairs were conducted as are those of the state of New York, according to the Committee on New York State Government Reorganization of the American Engineering Council of the Federated American Engineering Societies, in a report to the chairman, of the Joint Judiciary Committees of the Senate and Assembly. The report, just made public, was signed by the three members of the committee who were appointed by Herbert Hoover. They were H. de-B. Parsons, chair- man, Paul G. Brown and Lewis B. Stillwell. Although the American Engineering Council is a national organization, it decided to aid in governmental reorganization in New York State because of the magnitude of the task. The Council's committee in its report urged the passage of three state reorganization amendments for consolidation of departments, an executive budget system, and a four-year term for the higher state officials. In the words of the report :

Jan 1, 1921

By AIME AIME

I N JUNE, 1918, at a meeting of the American Society of Mechanical Engineers in Worcester, Mass;, a resolution was adopted for a committee to investigate the aims and organization of that society. This was followed subsequently by similar independent action on the part of the Society of Civil Engineers. The other two Founder Societies were approached and requested to appoint similar committees, the four committees to combine as a .Joint Development Committee, later called the Joint Conference Committee, to investigate what might be done in the way of coordinating those activities of the Founder Societies which ape of common interest, and which were then being pursued separately. The Joint Conference committee worked diligently -for almost. two years and. brought forth a tentative as outlined in its report which was published in full in MINING AND. METALLURGY, December, 1919. It recommended the formation of a nation-wide organization to be composed of representatives' of all of -the engineering societies, local, state, regional, or national, the object to be to further the interest of the public through the use of technical knowledge and engineering experience, and to consider and act upon matters common to the engineering and allied technical professions. Whereas the technical societies have large fields of endeavor in welfare work, and their prime. efforts are 'still in technical lines, this new organization was to be devoted entirely to service, looking to the welfare of the nation and the engineering profession, and to service for the public in local and state affairs.

Jan 1, 1920

By H. LeRoy Scharon, A. B. Cleaves

THE application of geophysical techniques in the A engineering surveys of the Philadelphia and Western Extensions of the Pennsylvania Turnpike System is unique inasmuch as this is the first time, (to the authors' knowledge), that such studies have been employed on a large scale on a major highway system. These investigations were confined to specific areas along the center line of the proposed Philadelphia Extension between Carlisle and King of Prussia, and the Western Extension between Irwin and the State line near Youngstown, Ohio, as shown in Fig. 1. Along the 100 miles of the philadelphia Extension, the geophysical surveys were confined to 137 individual cuts and comprised a total length of 37.4 miles of line. The Western Extension, 66 miles in length, has 108 individual cuts. The accumulated length covered by electrical resistivity studies was 17.3 miles. The depth of the cuts varied from a minimum of 10 ft to a maximum of 62 ft. The geophysical investigations were made for the purpose of determining depths to bedrock in the 245 proposed cuts and at the sites of various structures. The 'data also served as a basis for geological interpretations of the condition of bedrock, contact zones, rock types, water table, and other factors significant in highway construction. The geophysical method of investigation employed the use of the electrical resistivity principle using the Gish-Rooney type electrical resistivity meter and the Wenner electrode configuration.* Apparent resistiv- ities were determined for constant intervals to various depths and were correlated with surface geological observations and subsurface geological conditions revealed by key diamond drill holes situated within a given cut interval. From these correlations, depths to bedrock were postulated with notations on other geological features that might be pertinent to modern highway construction. Geology The bedrock underlying the areas of the extensions of the Turnpike afford an excellent academic study of the electrical resistivity depth method as well as a practical application to modern highway engineering. The rocks encountered on the Philadelphia Extension vary in age from pre-Cambrian to Triassic and Quaternary, whereas in the Western Extension, bedrock is confined to relatively flat-lying strata in the Allegheny, Conemaugh, and Monongahela formations of the Upper Paleozoic, Pennsylvanian. Glacial and Recent stream, valley, and terrace deposits are common. Philadelphia Extension The oldest bedrock encountered in this extension are igneous and metamorphic. These, encountered chiefly in Chester County, consist of the strongly

Jan 1, 1952

Jan 1, 1969