Search Documents

By JOHN S. HEARDING

ON the Minnesota Ranges, 600 million tons of material have been moved in the past three years to produce 172 million tons of direct-shipping iron ore. Increasing wage rates and cost of equipment and supplies, coupled with the larger amount of waste material to be moved in comparison with the quantity of ore make it imperative that tile industry adopt all practices and methods which will enable it to move earth at progressively lower costs. Drilling. Prior to and during the war practically all blastholes drilled were 6-in. in diameter and put down by drills using strings of tools weighing from 2000 to 3000 lb. Present trends indicate that heavier drilling equipment making 9-in. holes wit11 3000 to 6000 lb tools will be more economical. Holes up to 12 in. diameter will be made with this equipment. Forging and hardening practices for bits to increase footage is receiving attention. One manufacturer expects to market 9-in. bits having sintered carbide inserts in the reaming and cutting edges. Oxygen and oil to burn holes in the rock are being tested for making blastholes at a considerably greater speed than can be obtained with a blasthole drill on the same size hole. To dale, however, the cost has been prohibitive.

Jan 1, 1949

By T. D. Murphy, G. V. Henderson

The element silicon, with its usual partner, oxygen, plays the same role relative to inorganic materials as carbon and hydrogen play with respect to living organisms. The crystallographic structure of silicon dioxide (SiO2) consists of one atom of silicon well-nigh inseparably bonded to four contiguous atoms of oxygen, a gas of but slightly more than half its atomic weight, forming a three-dimensional network of SiO4 tetrahedra (Dietz, 1968). This wispy arrangement is the fabric of the mineral quartz which is one of the harder, more abrasive, and chemically stable raw materials to be found in Mother Nature's cupboard. Most of us are vaguely familiar with the observation that nearly 60% of the lithosphere to an approximate depth of 10 miles is composed of these two elements, which proportion actually rises to about 75% if the atmosphere, hydrosphere, and biosphere are included (Parker, 1967). Elemental silicon is a brittle steel-gray metalloid with a density of 2.42 and does not occur in nature. In its limited commercial form, which is still brittle and metallic in appearance, its density drops to 2.33. It combines with oxygen to form the gaseous oxide SiO, or the solid dioxide Si02 (analogous to its congener carbon in CO and CO2); a tetrachloride SiCI4 (analogous to CC14); or, combining with oxygen and one or more metal ions, forms the largest rock-making family of all, the silicates. Further, next to the feldspars, quartz is the most abundant known mineral and, in some form or another, accounts for roughly 12% of surficial terrestrial rock. It is this so-called "free silica" to which your attention is chiefly directed in this chapter. In any such consideration of silica, its several crystalline phases with their attendant differing physical properties appear worthy of delineation. Alpha quartz is the only one of this interesting polymorphic family that is thermodynamically stable at normal pressures and temperatures up to about 573°C. The low phases of tridymite and cristobalite can exist in the so-called metastable state below 117° to 200ºC but seldom occur in nature in these two different crystal forms (Sosman, 1965). Opaline silica, now considered by most researchers to be a variety of cristobalite, occurs in abundance and is the only exception. The three remaining polymorphs, keatite, coesite, and stishovite, also are metastable under ambient conditions. Keatite, however, is not known to occur naturally and has only been synthesized in the laboratory. The other two have been identified in submicron sizes and in microscopic amounts, occurring naturally as a result of high order shock-wave pressures generating quite elevated temperatures --such as might accompany the impact of a large meteorite on a hard sandstone terrain (Chao et al., 1962). An intriguing characteristic of these silica minerals, and one which has very practical applications, is their extremely variable densities. The classic 2.65 specific gravity of alpha quartz drops to 2.20 in tridymite, cristobalite, and lechatelierite (natural silica glass), as well as in many man-made glasses of commerce which are merely noncrystalline or amorphous solids in the form of super-cooled liquids which can no longer change their shapes (Pauling, 1950). It rises again to 2.50 and 2.93 for keatite and coesite, respectively, and finally becomes a reported 4.35 for stishovite-nearly a 50% range in density for the known physical combinations that silica naturally assumes (Frondel, 1962; Konnert et al., 1973; Pecora, 1960). Pursuing its esthetic aspects, briefly, silica is well-represented among gem stones which, to qualify as such, must have the attributes of beauty, durability, and rarity (Jahns, 1983). As quartzose gems usually have but one or, at

Jan 1, 1983

By Scott Tzcrner

WITHIN recent years people have begun to realize the importance and significance of the mining and allied industries. The leading part the engineer plays in civilization is becoming recognized. However accurate quantitative knowledge of the industrial importance of mining is still seldom possessed except by those close to this business. It is true that there are a few who go to the extreme and represent the whole progress of civilization as a reflection of man's gradual mastery of mineral utilization, but on the whole, the magnitude of the-industry is underestimated. In this paper I shall call attention briefly to the importance of mining in the United States, in Canada, and in the world. Ordinarily, the annual primary mineral production of the United States is about $5,500,000,000. The average for the last 5 years has been a little over that, but last year, sadly enough, it was less than 31/4 billion. Just now, we are on the decline, and have been for the last two years. In Canada, the 5-year average was about $268,000,000, and last year it was 227 million. Due in part to gold mines (in 1930, for the first time, Canada's gold production exceeded that of the United States), the Canadian average is holding up better than ours. Average world mineral production over the last -5 years has been estimated at about $12,000,000;000 whereas in 1931 it was less than than 8 billion.

Jan 1, 1932

HIGH-GRADE manganese ore, from which manganese is obtained commercially, is not found in large quantities in any major steel-producing nation in the free world. The U. S. is a "have not" nation with respect to deposits of directly mineable high-grade manganese ore. Known resources of 48 pct Mn or better grade ore amount to less than 200,000 tons. In 1950 the U. S. steel industry consumed 1.8 million short tons of metallurgical grade manganese ore that contained about 800,000 tons of manganese. About 16 pct of the manganese content was lost in processing, so that about 650,000 tons, or 13 pounds per ton of steel actually entered into steel production. Under present practices use expands directly with steel output, and by 1975 the demand in both the U. S. and the rest of the free world is expected to be roughly 60 pet greater than in 1950. In peacetime about 80 pet of manganese consumption goes into steel production; high-manganese steel, dry cells, and chemicals account for the remainder. The manganese supply problem centers around high-grade ore for ferromanganese production. Use of ores containing less than 35 pet Mn sharply increase the costs of making ferromanganese. Use of ferro-manganese of grade below 70 pet in turn requires changes in steelmaking that increase steel cost. Under normal conditions the present small domestic production cannot be expected to increase. Major resources in the U. S. consist of 12 low-grade deposits. The cost of mining and treating these ores to extract a product as good as that yielded by imported ores is at least twice and in some cases more than four times the 1951 price of foreign ores delivered to the U. S. However, as long as trade relations and overseas shipping are not interrupted, deposits in India, Africa, and Brazil can meet steadily increasing demand at approximately present costs. Cost considerations indicate that the U. S. should continue to rely upon overseas sources for its peace-time supply, and that this situation is satisfactory. But, this does not take into account the question of how the U. S. will be able to meet its needs in war. Position of the Rest of the Free World In 1950, free world steel producers outside the United States, with a steel output of 70 million ingot tons, consumed about 1.3 million tons of metallurgical-grade ore. Their manganese ore demand, expected to increase directly with steel production, will by 1975 be about 2.3 million tons. Russia possesses over half the known manganese ore reserves of the world and is producing twice the tonnage of any other country. It supplied more than a third of the U. S. manganese requirements up to 1938 and again in 1948, but by 1950 Soviet manganese exports to the free world had virtually ceased. The free world's supply of manganese now comes mainly from India and Africa. Somewhat over 10 pet of U. S. imports came from Brazil and Cuba. Security Considerations In the event of war the U. S. might be substantially cut off from 90 pet of present sources. Reduction in manganese specifications might cut consumption by over 10 pet without seriously affecting steel quality. By elimination of losses in the production of ferromanganese savings as high as 10 pet might be possible. But, wartime manganese requirements cannot be met through conservation alone. To meet possible future emergencies the U. S. should continue its comprehensive security program for manganese, including stockpiling and research on the economic use of low-grade ore, domestic ores, the recovery of manganese from slag and the reduction of manganese requirements in steel production. If this work, including additional pilot plant operation is pursued vigorously, it should be possible in an emergency to get an adequate supply of manganese from domestic sources. The national stockpile then can be looked upon as a source of supply during the period of at least 2 years required to reach full-scale production from low-grade resources. Ferromanganese Smelting In comparison with smelting of pig iron, ferro-manganese smelting is a very wasteful process. Under present ferromanganese blast-furnace smelting practice, about 8 pet of the manganese in the furnace charge is lost to the slag, and roughly the same amount is lost to the stack gases; the total loss approaches 15 pct. Present practice is a compromise between excessive slag loss and excessive stack loss. In fact, it may be seriously questioned whether conventional blast furnace design is suitable for manganese smelting. U. S. Resources The known manganese deposits of the U. S. contain a total of 3500 million long tons of raw material and 75 million long tons of metallic manganese. More than 98 pct of this contained metal is in 12 large low-grade deposits of which the most important are those at Chamberlain, S. Dak; Cuyuna, Minn.; Aroostook County, Maine; and Artillery Peak, Ariz. Reserves of high-grade ore (48 pct Mn) amount to less than 200,000 tons. About 20 million tons of ore average over 15 pct Mn, and when grade is decreased to 10 pct Mn reserves amount to about 100 million long tons. If cut-off grade is decreased to 5 pet Mn, resources amount to 800 million long tons. Many of these low-grade ores may be beneficiated by flotation or other concentration methods. Pyrometallurgical Methods For smelting ferromanganese, it is essential to have an ore containing at least 50 pct manganese, with an Mn:Fe ratio of about 8:1. Direct smelting of 20 pct Mn concentrates is not promising. The only method that offers any promise involves two-step smelting.

Jan 1, 1952

By W. P. Blake

THIS furnace is designed especially for the oxidation of sulphur or arsenic in pyritic ores, but may be used for all oxidizing or desulphurizing operations, and for calcining, roasting and chloridizing ores, or for drying ores in large quantities preparatory to treatment by magnetic separators or otherwise. It is of the tabular, revolving type, with automatic feed and delivery, and is a modification of the Cornish calcining furnace, designed by Brunton, from which it differs, however, not only in construction, but in two or more radical features, for which novelty is claimed and patents have been applied for. The principal of these novelties are: 1. A series of concentric terraced floors, one above another. 2. The introduction of superheated air upon the charge without contact with the fuel. In the furnace which I have had in operation for more than a

Jan 1, 1893

By R. A. Greenkorn, R. C. Smith

Hele-Shaw cells are used to model creeping flow through porous media (where Darcy&apos;s law is valid). The effects of inertia on flow about obstructions in a Hele-Shaw cell can be calculated by a perturbation method if one can determine a solution to Laplace&apos;s equation. Results of a computer solution for flow about circular, square and elliptical obstructions are presented. These results show that or a modified Reynolds number of less than I, the inertia terms are small; and for values of less than 3, the average streamline predicts the ideal flow. Therefore, the analogy might be used for studying flow in porous media up to a modified Reynolds number of at least 3. INTRODUCTION The nature of fluid flow in porous media is of interest in the fields of soil mechanics, ground water flow, petroleum production, filtration and flow in packed beds. Because it is very difficult to study the phenomenological behavior of flow in porous media, homologs and analogs are used to study flow characteristics. A Hele-Shaw model, made of two closely spaced plates - usually glass — is often used as an analogy to two-dimensional flow in porous media. Hele-Shaw2 showed experimentally that the streamline configuration for creeping flow around an obstacle located between two closely spaced parallel plates is the same as for two-dimensional, ideal flow about the same obstacle. Stokes7 verified these observations mathematically. The usual equation of motion for flow in porous media is Darcy&apos;s law. The form of the mathematical statement of Darcy&apos;s law is identical, within a multiplicative constant, to the expression for the average velocity over the plate gap in the plane of a Hele-Shaw model. These models may be used to describe flow in both homogeneous and heterogeneous porous media. In the mathematical proof of the Hele-Shaw analogy it is assumed that the convective terms in the Navier-Stokes equations are negligible and that the equations of motion degenerate to Laplace&apos;s equation, with pressure the dependent variable. Whenever a Hele-Shaw model is used as an analogy to flow in porous media, .the validity of this assumption is in question. Riegels5 showed that if convection is not neglected, the velocity distribution around a cylindrical obstruction in the flow field depends on a Reynolds number, the plate spacing, and a dimension characteristic of the obstacle. Riegels&apos; solution, a perturbation solution, uses the boundary condition that the flow rate into the obstacle averaged over the plate gap at any point on the obstacle is zero. The method requires that a solution to Poisson&apos;s equation for the perturbation pressure be found. Riegels evaluated this solution for the case of the cylindrical obstruction. His method may be simplified by eliminating the need for solving Poisson&apos;s equation for the perturbation pressure. Instead, an analytic expression for the perturbation pressure gradient is obtained (valid for arbitrary shapes) and used to eliminate pressure from the equations for the perturbation velocities. The results show, for symmetrical shapes, that if NRe < 1, the convective acceleration terms are small, and that the average velocities represent ideal flow up to at least NRe = 3, where: L is a characteristic dimension of the obstacle perpendicular to flow, b is the plate spacing, u is viscosity, v, is velocity of approach and p is density. THEORY* Incompressible fluid flow through a Hele-Shaw model and a porous medium are analogous because the equations for the average velocity components in two-dimensional flow are identical if:

Jan 1, 1970

By Edgar R. Kendall

A knowledge of the fundamental principles of locating, sampling, testing and evaluating materials is essential in prospecting for mineral aggregates. In this discussion, mineral aggregates will be considered sand, gravel, crushed stone and slag that are used as materials of construction. The quantity of mineral aggregates produced in the United States during the year 1935 for such purposes was roughly 165,000,000 tons, about 60 per cent of which was sand and gravel, 37 per cent crushed stone and 3 per cent crushed slag. The total value of this material was approximately $100,000,000. It is apparent therefore that the prospecting for suitable mineral aggregates is of considerable economic importance. In prospecting for mineral aggregates, the methods employed are the same whether the organization is large or small. In the large organization there may be available geologists for locating sources of supply, a land acquisition department to arrange for the necessary options or permits, engineers to do the sampling, a laboratory for testing, and a board of consulting materials engineers to make the final selection. Even small organizations must follow the same general procedure, though the responsibility for the selection of aggregates may rest with one man, who may or may not be an engineer, but who must depend entirely upon his own judgment. Locating the Supply The initial step in prospecting for mineral aggregates is the locating of suitable, adequate and economic sources of supply for the project in mind. Commercial plants in the vicinity should be investigated and a survey made of the existing structures that have been built of aggregates from these sources. If the structures are rather old and show no signs of deterioration, it is fairly good evidence that the aggregate is satisfactory. If materials of the proper quality can be obtained from commercial sources in sufficient quantity, and delivered to the job economically, it

Jan 1, 1942

By Edgar R. Kendall

A knowledge of the fundamental principles of locating, sampling, testing and evaluating materials is essential in prospecting for mineral aggregates. In this discussion, mineral aggregates will be considered sand, gravel, crushed stone and slag that are used as materials of construction. The quantity of mineral aggregates produced in the United States during the year 1935 for such purposes was roughly 165,000,000 tons, about 60 per cent of which was sand and gravel, 37 per cent crushed stone and 3 per cent crushed slag. The total value of this material was approximately $100,000,000. It is apparent therefore that the prospecting for suitable mineral aggregates is of considerable economic importance. In prospecting for mineral aggregates, the methods employed are the same whether the organization is large or small. In the large organization there may be available geologists for locating sources of supply, a land acquisition department to arrange for the necessary options or permits, engineers to do the sampling, a laboratory for testing, and a board of consulting materials engineers to make the final selection. Even small organizations must follow the same general procedure, though the responsibility for the selection of aggregates may rest with one man, who may or may not be an engineer, but who must depend entirely upon his own judgment. Locating the Supply The initial step in prospecting for mineral aggregates is the locating of suitable, adequate and economic sources of supply for the project in mind. Commercial plants in the vicinity should be investigated and a survey made of the existing structures that have been built of aggregates from these sources. If the structures are rather old and show no signs of deterioration, it is fairly good evidence that the aggregate is satisfactory. If materials of the proper quality can be obtained from commercial sources in sufficient quantity, and delivered to the job economically, it

Jan 1, 1942

By Stephen L. Bolivar, Susan H. Balog, Thomas A. Weaver

A data-classification scheme was developed to detect potential uranium mineralization in the Montrose l º x 2º quadrangle, Colorado. The methodology developed is a rapid and efficient method of resource evaluation on a reconnaissance scale. The necessary techniques were developed and refined to digitize, integrate, and register various large geological, geochemical, and geophysical data sets for the Montrose quadrangle, Colorado, using a grid resolution of 1 km. All data sets for the Montrose quadrangle were registered to the Universal Trans- verse Mercator projection. The data sets include hydrogeochemical and stream sediment analyses for 23 elements, uranium-to-thorium ratios, airborne geo- physical survey data, the locations of 90 uranium occurrences, and a geologic map (scale 1:250 000). Geochemical samples were collected from 3965 locations in the 19 200 km2 quadrangle; aerial data were collected on flight lines flown with 3-5 km spacings. These data sets were smoothed by universal kriging and interpolated to a 179 x 119 rectangular grid (each grid block is 1 km2). A mylar transparency of the geologic map was prepared and digitized. All possible combinations of three, for all data sets, were examined for general geologic correlations by utilizing a color microfilm output. Subsets of data were further examined for selected test areas. A classification scheme for uranium mineralization, based on selected test areas in the Cochetopa uranium district, is presented. Areas favorable for uranium mineralization, based on this scheme, were identified and are discussed.

Jan 1, 1982

By John Ward Smith

Dawsonite-bearing oil shale of Colorado&apos;s Green River formation offers a unique and vast (more than 5.9 Gt of A120 j) resource of easily extractable alumina. The processing methods required by the thermal reactions of dawsonite and its oil-shale carrier also require production of shale oil, soda ash, and nahcolite as marketable coproducts. These production methods are presented. The alumina production process is contrasted with the Bayer process to describe technical advantages of extraction of alumina from oil shale which may offset the problems associated with processing a relatively lean ore. While alumina production from oil shale requires development of new technology, the technical problems appear solvable. Only the political problems arising from the now onerous and completely unnecessary federal oil-shale withdrawal appear less solvable.

Jan 1, 1982

By A. G. Guy

IN the course of a research on steady-state diffusion it became necessary to make diffusion calculations for a finite solid. This problem was found to be sufficiently different from the corresponding problem for the semi-infinite solid for an entirely new approach to be necessary in obtaining a useful solution. The assumption of an exponential variation of the diffusion coefficient with concentration&apos; was no longer a practical necessity, so that the new solution offered the possibility of handling diffusion in semi-infinite solids for arbitrary variations of the diffusion coefficient with concentration. In discussing the principle on which this method of calculation is based, it is convenient to consider the relatively simple problem of one dimensional diffusion into a matrix that initially contains none of the diffusing substance. The solution of the set- ond Fick Law,?C/?t=D0?2C/?x2, for diffusion into a semi-infinite solid is3 C/C=1-F(x/2vD0t [1] where C is the concentration of the diffusing substance at a depth x cm below the surface after dif- A. G. GUY, Member AIME, and M. GOLOMB are Professor of Metollurgicol Engineering and Professor of Mathematics, respectively, Purdue University, Lafayette, Ind., A. S. YUE, formerly with Purdue University, is now with the Research Laboratory, Dow Chemical Co., Midland, Mich. TP 4505E. Manuscript, July 18,1956. fusion has occurred for t seconds; C, is the concentration of the diffusing substance at the surface of the matrix; Do is the diffusion constant, expressed in sq cm per sec; and + represents the Gauss error function. The corresponding solution for diffusion into a finite solid of thickness, 1, is conveniently written for the change in concentration, C+, at a point midway through the matrix and for times, t, great enough for the following equation to be used4 c1/2/C1=(1/2-2/?e-?2D0t/l2) [2] In Eqs. 1 and 2 the diffusion coefficient is represented by the symbol Do (rather than by D) to emphasize that these equations are valid only for constant values of D. To understand how these equations can be modified to take account of actual variations of D, such as that shown in Fig. 1, first consider the fact that for a given time of diffusion theconcentration at a given point is determined, not by the D value alone, but by the ratio x/vD0 in Eq. 1 and by a similar ratio, l2/D0 in Eq. 2. Even though in fact D varies, it is possible to keep this ratio constant by using a special coordinate system, x,, that varies with D in the appropriate manner. The necessary character of this special coordinate system can be easily visualized by imagining that

Jan 1, 1958

By J. D. Mote, A. Rosen, J. E. Dorn

The effect of strain rate and temperature on the critical resolved shear stress for (1100) [1120] prismatic slip was determined for the intermediate hexagonal phase containing about 67 at. pct Ag and 33 at. pct Al. Whereas the flow stress increased only slightly as the test temperature was first decreased below room temperature, a rapid increase inflow stress was obtained with yet greater decreases in temperature from about 240" to 4°K. The effect of both temperature and strain rate on the flow stress over the low-temperature range could be completely rationalized in terms of the Peierls mechanism when the deformation is controlled by the rate of nucleation of pairs of kinks. A few years ago Mote, Tanaka, and Dorn1 observed that the critical resolved shear stress for prismatic slip of a 67 at. pct Ag plus 33 at. pct A1 hexagonal intermediate phase by the (1100)[1120] mode decreased precipitously as the test temperature was increased from 4" to about 160°K. Their results for both basal and prismatic slip are given in Fig. 1. It is obvious that only the flow stress for prismatic slip is strongly temperature-dependent, whereas the flow stress for basal slip is independent of temperature. If the temperature dependence of the flow stress were primarily due to interstitial impurities, it might be expected that they would influence the flow stress for basal slip as well. Since the activation volume at 115°K for prismatic slip was determined to be about 15b3, where b is the Burgers&apos; vector, this thermally activated deformation process was tentatively ascribed as being due to the Peierls mechanism. But the various analyses of the Peierls mechanism then available as formulated by Seeger2 and also by Lothe and Hirth3 did not agree well with the experimental data. Since that time a more realistic theory for the operation of the Peierls mechanism under conditions where the strain rate is determined by the rate of nucleation of pairs of kinks has been presented by Dorn and Rajnak.4 The present investigation was, therefore, undertaken in order to provide the essential data for a careful check on the agreement between this theory and the low-temperature deformation by prismatid slip of the above-mentioned Ag2A1 intermediate phase. EXPERIMENTAL TECHNIQUE Single-crystal specimens so oriented that the [1120] direction and the normal to the (1100) plane were at 45 * 2 deg to the tensile axis were grown from the congruent melting composition of about Ag2Al for the intermediate hexagonal phase by the

Jan 1, 1964

By Orson Cutler Shepard

RECENT research work in the flotation concentration of minerals has been concerned mainly with flotation reagents and the mechanism by which collecting reagents are held to the surface of certain mineral particles. The fundamental question of why air bubbles cling to properly prepared mineral surfaces is usually dismissed with the statement that the surface is air-avid or water-repellent. In my article in MINING AND METALLURGY for June, 1932, I showed theoretically that surface tension relationships govern bubble attachment in Rotation. This explanation has not been accepted by many; probably be¬cause the difficulty of measuring solid-solution surface tensions prevented obtaining experimental evidence. If the surface tensions involved in the system [solution, mineral, air bubble] are responsible for attachment of the air bubble to the mineral, any change in the surface tensions should cause a corresponding change in the attachment of the air bubble. An example in which the mineral-solution surface tension could be varied was found with mercury. When mercury is in contact with solutions of certain electrolytes the surface tension at the contact of mercury and solution can be altered by electrical polarization of the mercury. The surface tension rises to a maximum as the mercury is given an increasing negative potential and then decreases with further increase in potential. The theoretical relation between the surface tensions and the attachment of an air bubble is given by the following equation:

Jan 1, 1936

H. N. EAVENSON, Gary, W. Va.-Judging from our own experience, the statement that only 40 per cent. of the accidents are caused by the human element is very low. We have adopted all the measures that Mr. Wilson recommended, such as systematic timbering, use of permissible expolsives and practically everything that anybody has suggested or can think of, and even after all that has been done, done for several years, and a systematic campaign maintained all the time to reduce accidents, we still

Jan 4, 1918

By E. I. Organick, B. H. Golding

A simple correlation is presented for the prediction of saturation pressures in condensate-gas and volatile-oil mixtures. Saturation pressure is related directly to the composition of the mixture with the aid of two generalized composition characteristics, B, the molal average boiling point, and W, the modified weight average equivalent molecular weight. The need for hydrocarbon equilibrium constants is entirely eliminated. Only the values of the two conlposition parameters need be obtained, and these are calculated in a simple and reproducible manner from the stream analysis of the mixture and the ASTM distillation for the heavy ends. The correlation is given .in the form of a set of 14 working charts in which saturation pressures, either retrograde dew points or bubble points, are plotted cs temperature, forming partial phase envelopes for mixtures having discrete values of the composition parameters, B and Wul. A locus of critical states on each chart intersects the partial phase envelopes, distinguishing retrograde dew point pressures from bubble pressures. A comparison Between experimental and predicted saturation pressures reveals that: the probable error of the predicted values, when considering the data as a whole (214 experimental points), is five per cent; for high gasjoil ratio condensate fluids (approximately 40.000 or more cu ft/bbl) the probable error is about 8 per cent. In either case, however, the probable error is comparable with the overall uncertainty of the data from which the correlation is derived. INTRODUCTION There is a present need for a simplified, yet reasonably accurate method for predicting upper phase boundaries of reservoir fluids. In the case of high gas/oil ratio fluids, namely the so-called highly volatile oils and the condensate gases, no simple method, accurate within 5 to 10 per cent, is now available by which bubble point and retrograde dew point pressures may be predicted. In order to calculate the upper phase boundary of a volatile reservoir fluid, using correlations now available, it is necessary to find and employ the proper K-values (equilibrium volatility ratios of the hydrocarbons in that fluid). This process of finding the Proper K-values usually involves a double trial and error computation. Since the K-values are in themselves dependent upon the composition of the fluid, their use in the calculation of a saturation pressure actually represents an unnecessary complication. The correlation described in this paper relates saturation pressure directly to the stream composition, entirely eliminating the need for K-values. The only data required to calculate the Stream composition are obtained from the customary low temperature fractional analyses of separator gas and liquidt and from the ASTM distillation of the c,+ fraction of the separator liquid. A considerable simplification in the procedure for predicting saturation pressures is thereby effected without significant loss in accuracy. BASIS FOR A CORRELATION Empirical relationships between the saturation pressure and the composition of the fluid in question have already been partially explored by one of the authors.V n particular, a relationship between the critical pressure for a hydrocarbon mixture and its composition was developed. The critical pressure is in reality a saturation pressure, as it repregents a limiting case either of a dew point or of a buhhle point pressure for any given mixture. It was found that the critical pressure may be correlated as a function of two generalized composition characteristics or variables. One characteristic expressed a molal average prop-erty, the other a weight average property of the mixture. Specifically, the molal average boiling point (MABP, or B as it

Jan 1, 1952

By Young C. Kim, Francis Martino, Ish Chopra

For the past two and one-half years, various emission control strategies were jointly developed by the University of Arizona and the Homer City Owners to com- ply with the clean air requirements at its Homer City Power Plant. Some of the available options for the SO2 emission control by the Homer City Owners were:l)cleaning of run-of-mine coal,2) scheduling of mining operations at its captive mines, 3) blending the captive mine coal with externally purchased low sulfur coa1,and 4) placing a partial FGD system. This paper describes two specific emission control strategies developed and implemented. These are: 1) production scheduling at the mining face to minimize sulfur variability, and 2) external purchasing of low sulfur coal for further blending. The main objective of this paper is to share our experiences on implementing the developed strategies. This paper emphasizesthe need for proper mine planning on a short-term basis, if the power plant is to meet the desired objective.

Jan 1, 1983

By A. G. Weber, H. J. Welge

A published calculation method for predicting incompressible, multidimensional fluid displacement has been adapted to the problems of water and gas coning in oil wells. Since depth and radial distance from the wellbore are the two key dimensions affecting the shape of a gas or water cone, coning calculations are well suited to the use of two-dimensional methods. The alternating direction implicit procedure (ADIP) was used for relaxation calculations of two-phase potentials in a two-dimensional grid. From the potentials and the capillary pressure relationship, saturation and pressure distributions were calculated which trace cone growth with time. Predictions have been made for well producing histories both before and after core breakthrough. To check validity of the method, two-dimensional calculations have matched the coning behavior and produced water-oil ratio history of a laboratory sand-packed model. They have also matched the coning behavior of several producing wells, for which the calculations were compared with produced water or gas cuts and logs showing water or gas cone movements. INTRODUCTION The application of two-phase, two-dimensional calculations using ADIP to various reservoir flow problems has been described in the literature.1-3 When adapted for computer solution, this method has proved to be a powerful tool for simulating well and reservoir behavior. This paper discusses the method as applied to well coning calculations. Single-well and coning calculations comprise an especially difficult class of two-dimensional problems which require special techniques for computer calculation and determination of reservoir characteristics. Refs. 4 through 8 describe previous approaches to the coning problem. Several examples of water and gas coning calculations, including studies on both laboratory models and producing wells, are presented here. The two-dimensional method accounts realistically for the most critical parameters affecting coning behavior, including production rate, formation stratification, horizontal and vertical permeabilities, depth of well penetration, gravity and capillary forces. The method considers the different densities and viscosities of the two phases and the relative permeability and capillary pressure characteristics of the rock and fluids. In addition to tracing cone growth in the vicinity of the wellbore, the method calculates the overall movement of the fluid interface throughout the well&apos;s drainage volume. Incompressible fluid flow is assumed to occur between the producing interval and the well&apos;s limit of drainage. Calculations can be made for the producing history both before and after cone breakthrough. A typical two-dimensional grid or array of blocks used to solve a coning problem contains about 400 blocks. The well&apos;s cylindrical drainage volume can be represented by about 20 radial subdivisions and the formation thickness by 20 vertical subdivisions. The grid spacing is normally smaller near the withdrawal interval to define the cone shape accurately. For this work we used an IBM 7074 digital computer having a core memory of 10,000 ten-digit words. A typical study, covering 5 to 10 years of well producing history, required from three to six hours of computing time. MATHEMATICAL SIMULATION OF CONING BEHAVIOR BASIC METHOD In coning calculations, the reservoir volume drained by the producing well is represented by a two-dimensional system of blocks as shown in Fig. 1 for water coning studies. The horizontal dimensions of the blocks increase with radial distance from the well axis in geometric progression, i.e., the block size is small near the wellbore and large near the well&apos;s drainage radius (re). Vertically, the blocks are bounded by horizontal planes located at different depths through the

Jan 1, 1965

By R. J. Blackwell, A. L. Pozzi

Scaled laboratory-model studies provide a powerful method for evaluation of a proposed oil-recovery process. In recent years, models have been used extensively to evaluate processes in which solvents displace oil, both for general cases and for specific reservoir conditions. Since the performance of a miscible flood in a horizontal reservoir can be significantly affected by transverse mixing between solvent and oil, this displacement mechanism must be accurately simulated in the scaled model studies. Unfortunately, precise scaling of transverse dispersion coupled with the requirement of geometric similarity requires impractically large laboratory models and long times for experiments. If scaling requirements for miscible displacements could be relaxed while accurate simulation of essential displacement mechanisms is maintained, the utility of model studies would be greatly enhanced. The purpose of the work reported herein was to evaluate the relative importance of various mechanisms affecting miscible displacement and to ascer tain whether the essential features of the displacement process can be simulated even though some scaling groups are not satisfied. These studies were performed with completely miscible systems in linear, horizontal models packed with unconsolidated media. From the experimental results, a set of relaxed scaling criteria was formulated which allows the requirements of geometric similarity and equality of the ratio of viscous to gravity forces to be omitted for specified conditions. The relaxed criteria are valid whether transverse mixing is by molecular diffusion or by convective dispersion. Correlations which permit prediction of vertical sweep efficiencies in linear, horizontal reservoirs were developed from the experimental data when transverse mixing is by molecular diffusion. These same correlations may be used when transverse mixing is by convective dispersion if an empirically defined, effective, transverse dispersion coefficient is used in the description of the mixing process. The effective transverse dispersion coefficient correlation essentially duplicates the dispersion coefficient correlation for equal-viscosity, equal-density fluid systems. Experimental values for the effective transverse dispersion coefficient can be measured readily. INTRODUCTION One of the most effective methods for evaluation of miscible-displacement oil-recovery processes is that of displacements in laboratory models scaled to simulate reservoir conditions. For these laboratory studies to be meaningful, however, the essential displacement mechanisms affecting reservoir performance must be accurately simulated. Since the performance of a miscible flood in horizontal reservoirs, or in dipping reservoirs at high rates, can be significantly affected by transverse mixing of solvent and oil, this mechanism must be considered in the design of laboratory experiments. Unfortunately, precise scaling of transverse dispersion coupled with the requirement of geometric similarity requires impractically large laboratory models and long experiment times. This difficulty seriously limits the utility of laboratory model studies. Craig,et al,1 demonstrated that geometric similarity is not required when mixing is unimportant. Their experimental data indicate, for the cases studied, that the displacement is sufficiently characterized by scaling the ratio of viscous-to-gravitational forces. This work suggests that relaxation of the requirement of geometric similarity and, possibly, other criteria might also be permissible when mixing is important, provided suitable groups describing the mixing process are scaled. The purpose of the work reported here was to evaluate the relative importance of various mechanisms affecting miscible displacement and to ascertain whether the essential features of the displacement process can be simulated even though some scaling groups are not satisfied. Consequently, laboratory investigations were made of the dependence of recovery on dispersion and other variables,

By A. C. Freeze

The first use of electric punched card accounting machines as an aid in calculating reserves at the Sullivan mine in Kimberly, B.C., was made in January, 1948. At that time their use was limited to totalling individual reserve blocks for the various reserve classes and for calculating total metal content. The immediate objective was to increase speed, improve accuracy, and to effect some savings in labor that could be employed more usefully elsewhere. It was recognized also that the potential for achieving even greater advantages was excellent. The initial experiment proved so successful that it was inevitable that the use of the method would expand. Thus, for the past nine years assay data from core hole and development headings have been processed by these machines and the results integrated with the program of calculating reserves. It was also learned that the machines could store and classify a large amount of other information concerning the mining characteristics of each reserve block in addition to tonnage and metal content. This has proven very useful for the preparation of monthly production reports as well as in long term planning, in forecasting production schedules, and in analysing the results achieved.

Jan 4, 1961

By F. C. Frischknecht

Most early development and application of electromagnetic prospecting methods took place in Scandinavia, where geological conditions favor their use. In other parts of the world these methods have aroused cycles of interest, but in Scandinavia they have been used continuously and successfully since the 1920&apos;s. Electromagnetic methods may be classified into two general groups. One group includes methods in which the source of the electromagnetic field remains stationary while the receivers are moved about to explore the area. The other includes procedures in which the energizing and receiving systems are moved together. Other classifications could be based on the size of the energizing source, the particular components of the electromagnetic field which are measured, or the mode of transporting the equipment. The difference between fixed-source and moving-source methods, however, is of such great fundamental importance that it will be emphasized in this discussion. FIXED-SOURCE METHODS Essentially, a fixed-source method consists of the measurement of electromagnetic fields about the source. The mutual coupling between the source and the earth is constant, but the mutual coupling between the receiver and the earth (unless the earth is homogeneous) and also between the source and the receiver changes at each station. The results are usually normalized by relating the field data to the calculated free space or primary field. Turam and Radio Reference Signal Methods: The turam or two-frame* (see Fig. 1A) is probably * Turam means two-coil. the most common fixed-source method. The energizing source is an insulated cable grounded at both ends or formed into a large rectangular loop. Measurements are taken along a traverse at 5 to 50-meter intervals using two small receiving coils, the lagging coil being placed at the position previously occupied by the leading coil. The complex ratio (i.e., inphase and out-of-phase ratios) of the voltages induced in the two coils is measured. Operating frequency range is about 100 to 800 cps. In a typical turam survey a straight, grounded cable several kilometers long is laid out parallel to the probable strike of the ore deposits or conducting strata being sought. An area extending 1 or 2 km on each side of the cable, and within 1 or 2 km of the ends of the cable, is surveyed. Measurements are made at stations 5 to 25 m apart along traverses perpendicular to the cable. Measurements may be made along lines parallel to the cable to serve as base lines for the traverses or for other special purposes. Commonly the receiving coils are oriented with their planes horizontal so that only the vertical component of the field is measured. If additional information is required, one of the hori- zontal components may also be measured by orienting the coils with their planes vertical. In a modified turam technique developed recently for both ground and airborne measurements (Fig. 1B) the amplitude of the complex voltage induced in a single receiving coil is measured and its phase compared with that of a reference signal transmitted from the energizing system by a radio frequency carrier. Thus the un-normalized field is obtained directly, whereas with the turam method it is obtained by calculation from the ratios. The turam method and its modifications have a greater working depth than the other electromagnetic procedures used in ore prospecting. Under favorable conditions conductors have been located at depths of 200 to 300 m. A modified turam method with one of the electrodes grounded in the upper end of a plunging orebody was used to follow the extension of this body to a depth of 200 m beneath a layer of conducting schists. Straight grounded cables are usually preferred to insulated loops because they are easier to lay out and because they often make the method more sensitive. The greater sensitivity of a grounded cable is a result of ground return currents which may flow in the orebodies in addition to the eddy currents caused by induction from the current in the cable. Anomalies in the vertical field due to eddy currents are characterized by a correspondence between high values for the inphase component and positive out-of-phase components and/or low values for the inphase component and negative out-of-phase components. Also the inphase component may approach zero, but it does not become negative. In very long continuous conductors that are parallel to a grounded cable the effect of ground return currents may far exceed the effect of eddy currents. These ground return currents cause a lack of correspondence between the inphase and out-of-phase components and may cause negative inphase or anti-phase components. It becomes difficult to carry out the measurements and often difficult to interpret the results. Such results immediately suggest the presence of graphitic strata, however, since ore deposits are rarely extensive enough to accumulate sufficient ground return current to cause these results. A cable laid out perpendicular to the strike or an insulated loop is sometimes used in areas where graphitic schists and slates are present. Anomalies are then completely or almost entirely due to eddy currents and are easier to interpret. The measured voltage ratios are normalized by either subtracting or dividing by normal field ratios calculated from free space considerations. The normalized ratios are then plotted as individual profiles. When significant anomalies occur in the ratio measurements, the actual normalized fields are calculated by beginning with a measured or an assumed value for the field at a point near the cable and successively multiplying this value by the normalized ratios. There is a similarity between this process and a numerical integration of the ratio curve. Conversely, in many respects the ratio curve is similar to the first derivative of the field curve.

Jan 1, 1960