Search Documents

One of the most unusual assignments in the his¬tory of Loffland Bros. Co. is now in progress with the drilling of a 72-in. diam. shaft in Nevada for the United States Atomic Energy Commission. Projected depth being 3200 ft, by volume, this is the same as a 216,672-ft hole 83/4 in. in diam. Every aspect of the operation is king-sized. The 15,000-lb bit moves into position over the well on a specially-made railroad car riding on rails 14 ft apart. The single drill collar weighs 300,000 lb, is 60 in. in diam., and 43 ft long. The drill pipe is 133/s-in. 72-in. N-80 casing fabricated with special tool joints. The bit chews up 1.05 cu yd of rock for every ft of penetration (This is equal to the volume of 67.71 ft of 83/4-in. hole.

Jan 9, 1964

By J. C. Konopka, S. A. G. Poppen, E. K. Roesner

Many shafts have experienced stability problems during shaft sinking because the designer failed to fully appreciate the conditions he would encounter. Some shafts have failed during construction because the ground supports provided to compensate for the expected conditions were inadequate despite the most careful investigations and analyses. To design a ground support which is ultimately safe to achieve stability during shaft sinking would be too costly and impractical and, therefore, many shafts would simply not be constructed. The design of a ground support for shaft sinking based on an intimate understanding of the expected ground behaviour and stress development during excavation combines the art of mining with the science of geotechnical engineering. Where no historical design data is available, the designer of the ground support must: 1. classify the rocks and soils and assess their behavioural characteristics; 2. calculate the primary and secondary stresses; 3. design and/or select a ground support system which will ensure stability of the excavation during shaft sinking.

Jan 1, 1983

To assist the taxpayer of the oil and gas industry in correctly and expeditiously preparing his Federal tax returns, the Bureau of Internal Revenue has prepared a "Manual for the Oil and Gas Industry Under the Revenue Act of 1918." Although the endeavor has been made to anticipate all questions that may be asked, it is recognized that such a manual is only general and cannot cover all cases that may exist. The Manual is based largely upon information gathered during the fall of the year 1918 by a corps of geologists, technologists, and engineers. The investigation was undertaken primarily to furnish a basis for arriving at valuations, and depletion and depreciation deductions in connection with oil and gas properties. All fields in the United States were canvassed. Records of production of thousands of properties were collected and tabulated. These were carefully classified and studied by the most competent and experienced men in the country and the average future production curves and tables of valuation data were produced as a result of this study. Be American! Work and Save. Buy W. S. S.

Jan 7, 1919

By F. C. Farnham

In this paper it is shown that the vertical component of the earth's magnetic field for the area of the United States can be very closely approximated by assuming it to be the sum of the vertical components of two magnetic fields. The first of these is the field of the centered dipole described by J. Bartels,l the axis of this dipole intersecting the earth's surface at two antipodal points, the one in the Northern Hemisphere being at latitude 78.5°N. and longitude 69°W., and the dipole having such strength that the vertical component of its field at its axis pole is 0.63 oersted. The second field is that due to a second dipole situated halfway between the center of the earth and a point on the earth's surface at latitude 38.5°N., longitude 91.5°W., the axis of this dipole being along this radius, the south pole being toward the surface, and the dipole being of such strength that its field at the point on the surface mentioned above is 0.069 oersted. Using the field computed on this basis, tables of latitude and longitude correction factors were computed and are included in the paper. It is also shown that the secular variation in the earth's magnetic field may be roughly accounted for by assuming it to be due to motion of the second dipole described above. Although there is an error in the equation used for computing the strength of the field due to the second dipole, the distribution of the field computed is very nearly that of the assumed arrangement of dipoles. Subsequent work by the author reveals that minor changes can be made in the location of the second dipole, which will make the computed field fit the observed field even more closely. It has also been found2 that the vertical component of the field may be represented equally well by a purely empiric relationship.

Jan 1, 1940

By F. C. Farnham

In this paper it is shown that the vertical component of the earth's magnetic field for the area of the United States can be very closely approximated by assuming it to be the sum of the vertical components of two magnetic fields. The first of these is the field of the centered dipole described by J. Bartels,l the axis of this dipole intersecting the earth's surface at two antipodal points, the one in the Northern Hemisphere being at latitude 78.5°N. and longitude 69°W., and the dipole having such strength that the vertical component of its field at its axis pole is 0.63 oersted. The second field is that due to a second dipole situated halfway between the center of the earth and a point on the earth's surface at latitude 38.5°N., longitude 91.5°W., the axis of this dipole being along this radius, the south pole being toward the surface, and the dipole being of such strength that its field at the point on the surface mentioned above is 0.069 oersted. Using the field computed on this basis, tables of latitude and longitude correction factors were computed and are included in the paper. It is also shown that the secular variation in the earth's magnetic field may be roughly accounted for by assuming it to be due to motion of the second dipole described above. Although there is an error in the equation used for computing the strength of the field due to the second dipole, the distribution of the field computed is very nearly that of the assumed arrangement of dipoles. Subsequent work by the author reveals that minor changes can be made in the location of the second dipole, which will make the computed field fit the observed field even more closely. It has also been found2 that the vertical component of the field may be represented equally well by a purely empiric relationship.

Jan 1, 1940

By Ove Sandberg, Olav Bowitz

The operational characteristics of the Soderberg vertical spike anode are briefly discussed stressing the importance of the flow properties of paste in the fluid zone, the thermal shrinkage in the carbonizing zone, and the surface disintegration in the consumption zone. The requirements for paste recipe and binder quality are combined with design and operation of cell. A low temperature susceptibility of viscosity and low thermal shrinkage of paste together with a low microporosity of the binder coke are important properties. PRACTICAL application of Soderberg's idea of a selfbaking carbon electrode proved successful just before 1920. Shortly after, experimental work was started with the aim of developing a continuous electrode that could be adopted as anode in aluminium reduction cells. The intermittent operation of a large number of small prebaked anodes made the idea of developing a continuous anode for electrolytic production of aluminium especially tempting. Moreover, the electrode consumption in this process, even on a theoretical basis, is very high. Many installations were carried out in the 1930's and during the Second World War. During the tremendous post-war expansion of the aluminium industry, the Soderberg electrode has been steadily more widely adopted. Thus, today more than 60 pct of the Western World's output of aluminium is produced in cells with selfbaking anodes, see Big. 1. The quality of the anode paste of Sfiderberg elec- trodes is considered a major factor influencing the specific carbon consumption. The purpose of this paper is to survey the fundamental requirements which must be met in order to obtain good anode operation. We have limited this paper to a discussion of Elektrokemisk's research on the vertical spike type anode. I) FUNDAMEKI'TALS OF ANODE CARBON PERFORMANCE A) Brief Introduction. The only practical method for producing a conductive carbon anode of the size required is to form and carbonize a mixture of a carbonaceous binder and a precalcined dry aggregate coke. In the Soderberg electrode, the forming and carbonization take place in the electrolytic cell

Jan 1, 1962

By George B. Clark, Edward E. Hornsey

Pulses from large underground explosions which traverse the rock beyond the "fracture" and "plastic" zones do not behave as a spherical elastic model. Observed attenuation is greater than that predicted by the elastic wave equation, and the pulse form changes in a different manner, i.e., it usually lengthens with the first power of the distance. To more clearly define a mathematical real earth-wave model, detailed analyses of the spherical elastic and the Voigt viscoelastic models have been made, and results compared with observed wave forms from large confined chemical and nuclear explosions. TRANSIENT SPHERICAL ELASTIC WAVES Scope of Investigation Transient elastic spherical waves were investigated in detail. However, an elastic model is not, in general, an exact representation of wave propagation in rock. An understanding of transient elastic waves is desirable for gaining insight into explosive-generated wave phenomena because it can be employed for comparison of more complex and realistic models, such as the Voigt model, or others which may simulate real earth waves. The study was concentrated primarily on the peak values of the radial wave parameters : displacement, particle velocity, acceleration, stress, and strain.

Jan 1, 1972

By Frederick Laist, H. J. Maguire

The ore from the Butte mines of the Anaconda company is quite siliceous; that is, it contains considerably less iron than is needed for the fluxing of the silica. The direct smelting of this ore, therefore, requires the addition of considerable fluxing material. The only flux available in sufficient quantity at Anaconda is limestone containing no metallic minerals. This necessarily makes the direct smelting of the ore so expensive that it is more profitable to subject the ore to a preliminary treatment by concentration. However, as the losses in the concentrator were very high, compared with the losses in the blast furnaccs, it was found, by calculation, more profitable to send ores containing more than a given percentage of copper to the blast furnaces, in spite of the higher costs of treatment. The dividing point was dependent on various factors, the chief of which was the prevailing market price of copper. It was customary, therefore, to segregate the ore as mined into two classes. Ore in the first class generally contained 5 per cent. or over of copper; this was sent directly to the blast-furnace department. Second-class ore contained less than 5 per cent. of copper, and averaged around 3 per cent.; it went to the concentrating department. With the introduction of the flotation process, it mas found possible to maintain an average recovery, as concentrates, of 96 per cent. At the same time, the cost of reverberatory smelting was very materially decreased by the use of pulverized coal. These two changes in practice made the blast furnaces unable to compete with the reverberatory furnaces on a cost basis. The distinction between first- and second-class ore was therefore abandoned, and the ore was treated by concentration. Obviously, on ores as high in iron as the Butte ores, the concentrator produces a product that is self-fluxing; in fact, it is possible to produce a concentrate containing more iron than is necessary to flux the silica. Under these conditions, the amount of basic fluxing materials required for the smelting operations became very srnall and the converter slag lost its former value as a blast-furnace flux. For this reason, a less expensive method of recovering the copper, silver, and gold contained in it than smelting in blast furnaces had to be found. It was not feasible

Jan 1, 1921

By Frank Calvin Roberts

An examination of the various devices employed for operating blast-furnace charging-bells has led me to design the arrangement slrown in the accompanying figure. In order to contribute to the even distribution of stock, the movement of the bell should be in a vertical line, since any tendency to side-thrust which may be in-

Jan 1, 1888

By J. M. Gaines, C. H. Herty, M. W. Lightner, H. Freeman

Few subjects have attracted the attention of metallurgists more than oxygen in steel. From the days of Mushet and Ledebur interest in this subject has been increasing, and as additional knowledge has become available, the problem has naturally grown more complex. Instead of using the simple term "oxygen" we now distinguish between iron oxide, silicates of various kinds, oxysulfides, oxygen as gas and oxygen in solid solution in steel. There are five general methods for determining oxides in steel: hydrogen reduction; vacuum fusion; various wet-extraction methods, including electrolytic methods; methods depending on volatilization of the iron away from the oxides; and metallographic methods. For oxygen in solid steel each of these methods has both advantages and disadvantages. The hydrogen-reduction method is of no use on steels above about 0.20 per cent. carbon;' furthermore, it gives only FeO and possibly some MnO. The vacuum-fusion method2 is expensive and gives total oxygen, with the exception of some A12O3, and does not differentiate between the various oxides in which the oxygen exists. Most of the wet extraction methods3 give only the more insoluble oxides SiO2 and A12O3, though the iodine method gives MnO to an uncertain degree (information that may be more misleading than no information

Jan 1, 1930

By E. A. Kilinski

THE mineral production of Dutch Guiana has been of little consequence. This is due to several rea-sons. Inaccessibility is probably the greatest factor, for the Guianas are off the main commercial route. More or less closely related causes are the tropi-cal climate and the temperament of the inhabitants. Small quantities of gold have come from Dutch Guiana for many years, and recently bauxite has entered the list of exports. It is likely that other minerals may be found in commercial quantities. The Colony is on the northeast coast of South Amer-ica. It is known by two names, that of Dutch Guiana, and that of Surinam. - British Guiana (Demerara) adjoins it on the west, French Guiana (Cayenne) on the east, and Brazil on the south. It covers an area of approximately 58,000 sq. miles. The population, in the. neighborhood of a hundred thousand,, is small, but the variety of races and the sub-sequent mixtures of these is almost incredible. This unusual and colorful population readily falls into three groups, (1) those of the bush, (2) those of the planta-tion, and (3) those of the towns. The bush people con-sist of two groups, the Indians and the bush-negro. The Indians, of whom there are but a little over two thousand, keep entirely to themselves, lead a. very primi-tive existence, and rarely come into the towns. The bush-negro gives the touch of human life to the thick jungles. A descendant of escaped slaves of by-gone days, he is at present a proud, stalwart, happy, clean, moral, carefree and ease-loving individual-a distinct personality. Work is not his pal, although he does cheerfully that which is necessary for his existence. He will transport passengers and goods in his dugout and guide the stranger through the jungles, but that is all. The plantations employ some negroes, but more Javanese, imported as contract labor from the East Indies. Paramaribo, the only large town in Dutch Guiana, is the center of all government, commercial, and social activities. It has a motley population of 40,000, in-cluding negroes native to Dutch Guiana and many from all parts of the West Indies. In addition, there are Javanese, Chinese, and some Hindus. The two latter groups control most of the retail trade. The Dutch and a few scattered Germans are the only Europeans. All of the higher government offices are held by the Dutch, the others are filled from the ranks of the natives. Marriages and intermarriages among these various groups have produced types that defy almost any effort to decipher an individual's forbears. Dutch is the official language, but among the people a jargon known as Tahki-Tahki holds sway. English is taught in the schools, consequently many speak it, and many more can make themselves understood in that language.

Jan 2, 1928

By H. Brandhorst, C. G. Dunn

THE main purpose of the present note is to provide further information on the effect of orientation on strain-induced grain boundary migration in sheet material. A secondary purpose is to draw attention to the presence of a possible (hkl) dependent surface energy driving force, when the two grains of a bicrystal specimen have different (hk2) planes at the gas-metal interface, and to suggest means of eliminating this effect from the strain effect. If two grains A and B of a bicrystal have specific surface energies ? A and ? B respectively, there exists a driving force for grain boundary migration equal to 2(? B - ? A)/t, where t is the thickness of the specimen.' When t is quite small and the residual strain energy densities €A and €B of grains A and B, respectively, adjacent to the boundary are nearly equal, it is possible that the surface effect may be larger than the strain effect. he difference € B - € A gives a driving force per unit area of grain boundary due to an applied strain.)2 However, with increasing t the surface effect decreases while the strain effect presumably remains constant. Therefore, at some sufficiently large value of t, it is possible to ignore surface energy driving forces.* On the other hand, the surface effect is eliminated for all value of t when both grains have the same (hkl) orientation or have identical values of surface energy. Although the previous study provided information on the effect of orientation on strain-induced erain boundary migration,' no orientations with the (100) plane in the plane of the sheet were included. The present paper provides information of this kind. A seed crystal reorientation technique4 was used to prepare a large bicrystal of silicon iron (3 1/4 pct Si) consisting of two (100) grains in the (100) [001] and (100) [Oil] orientations. After a cold rolling strain (7 pct reduction to 3/4 mm final thickness), small specimens were prepared as before2 and then annealed in hydrogen. The boundary migration was such that the grain in the (100) [011] orientation always grew. After overnight anneals at 1100° or 1000°C, none of the initial (100) [001] grain remained. An anneal of 30 min at 950°c, however, provided information on the start of boundary migration. Fig. 1 shows both the initial position (lower line) and the final position (upper curved line) of part of the boundary, as revealed by thermal grooves. In a different area, part of the final boundary was not revealed by thermal grooves; the rate of boundary migration presumably was too high for the growth front to be defined by the time dependent thermal grooving process. In another area there was a vacated intermediate position connected to the initial position of the grain boundary. This indicates that only part of the boundary

Jan 1, 1962

By Nicholas J. Grant, H. C. Chang

EMPHASIS on the importance of grain boundary sliding as a mode of deformation at elevated temperatures has been presented elsewhere.' The extent to which boundary sliding occurs under certain creep conditions has been determined for high purity aluminum2,3 and aluminum alloys.' In general, boundary deformation extends quite far into the adjoining grains, resulting in a rather wide band of deformation along the grain boundaries. This has led some investigators to doubt that grain boundary sliding consists of shearing along the boundary surface; it has been contended instead that boundary sliding is a result of concentrated slip in the neighborhood of the deformed grain boundaries."' The purpose of this note is to present evidence that grain boundary sliding takes place by a bulk shear process. gh purity polycrystalline aluminum, wherever and whenever there is grain boundary sliding, boundary migration and concentrated deformation along both sides of the deformed boundary are associated with it. Therefore, it has been rather difficult to obtain unambiguous evidence of boundary sliding. On the other hand, it would be expected in certain alloys of aluminum, when tested under particular conditions. that the severity of the interfering effects of boundary migration and concentrated deformation along the deformed boundary might be reduced. Current research in this laboratory' shows that a 20 pct Zn-A1 solid solution alloy fractures in an intercrystalline manner during creep at 500°F with a small total elongation of not more than about 14 pct, and that it does so with extremely limited grain boundary migration. Accordingly, this alloy was chosen for the present study. The experimental procedure was similar to that used in previous work and has been presented elsewhere.' Two parallel flat surfaces were milled from a round specimen. The gage portion of the specimen was 1 in. x .09 in. x .17 in. The specimens, which were annealed at 1030°F for 24 hr, showed two to four grains across the width of the test bar. The specimens were subjected to creep at 500°F at stresses of 2000 to 5000 psi. The rupture times were from 10 sec to 3 hr. Appreciable boundary sliding occurred in all the tests. A typical example of boundary sliding is shown in Fig. 1. (The tension axis is vertical in the micrographs.) Sliding has taken place along the boundary between grains A and B unaccompanied by important boundary migration. The sharpness of the offset at the triple point can be clearly seen in grain C. As a result of sliding along the boundary between grains A and B, a new boundary surface between grains A and C was created. The offset at the triple point is about 0.07 mm. This boundary sliding is accompanied by the formation of rather sharp kinking bands and, of course, slip on several slip systems in grain C. This type of deformation has been referred to as fold formation' in previous work with high purity aluminum.

Jan 1, 1957

By E. P. Valby

A method is presented in which the hydrocarbon weight fractional analyses of the well effluents from a true gas-tip-portion well and a true dark-oil-ring well furnish the basic data for determining the properties of any mixture of production from the two sources. The effect of injected gas on these properties can be computed. Comparison of similar properties of a given well effluent to the properties of mixtures of the basic well effluents will give the relative amounts of production from the two sources and injected gas. Presentation of Problem Oil fields having an area of gas-cap, or light-oil production, over the dark-oil area present a problem of increasing gas-oil ratios during the production of an oil well. The use of pressure maintenance in a field such as above, or a cycling project, wherein residue gas from an absorption plant is injected into the reservoir, adds to the problem, because a part of the increased gas-oil ratio may be due to the production of injected gas. The usefulness of a means to determine the amount of injected gas in a well effluent led to the development of a method in which well-effluent analyses of a true gas-cap-portion well and a true dark-oil-ring well furnish the basic data needed to determine whether injected gas of a known composition is present in a given well effluent. Development op Method The method presented herein is based upon the principle that if two fluids, or well effluents, having different properties are mixed in known proportions by weight, • the properties of their mixtures can be computed. Conversely, if these basic data are known, the properties of a mixed well effauent can be used to compute the relative amounts of each type of well effluent in the mixture. A convenient way of making these computations is to have the fractional analyses of the base well effluents and mixtures expressed in weight fractions The mathematical equations expressing the properties of mixtures will be developed for a two-component system consisting of the well effluents from the dark-oil ring and the gas-cap area. The added effect of injected gas, a third component, will also be developed. The following assumptions have been made in developing the method: 1. The gas-cap and dark-oil fluids exist initially in separate portions of the reservoir. 2. The fluids in each portion exist in a single phase at pressures above the saturation pressure for the dark-oil fluid. 3. The composition of each fluid is substantially constant throughout its respective portion of the reservoir. 4. Changes in reservoir pressure and temperature will not change the composition of the fluid entering the well bore. 5. The injected gas displaces original gas-cap fluid 100 per cent. •• 6. AS the injected gas travels through a

Jan 1, 1945

By J. Philip Neal, Carroll P. Rogers

Feldspars, the most abundant minerals of the igneous rocks, occur in numerous forms and mixtures. The feldspars of commercial significance are found in widely distributed pegmatites as large crystals usually free of iron- bearing impurities and thus suitable for hand-cobbing, and also in larger bodies where the ore contains various types of feldspar inter- mingled with quartz and relatively free of iron- bearing impurities, or at least readily unlocked from impurities present at relatively coarse mesh. The latter type of ore includes some pegmatites, and the ''alaskite" bodies so common in the Spruce Pine district of North Carolina. On the west coast of the U.S. and in Oklahoma there is-r has been--commercial recovery of natural feldspathic sand as a source of alumina in glass and ceramics. "Aplite" in commercial terminology is a light-colored igneous rock with a granitic composition and a fine sugary texture, often banded with readily removable iron impurities. Two areas in Virginia produce aplite for the glass industry: one located in the vicinity of Piney River, Amherst County, and the other near Montpelier in Hanover County. According to Deer et al. (1966) the word feldspar derives from the Swedish feldt or falt (field) and "spath:" chunks of rock appearing in tilled ground overlying granite. Castle and Gillson (1960) indicate a Germanic origin, citing "spat," which is said to refer to any transparent or translucent material which is readily cleavable. The term "spar" has in the past been applied to minerals other than feld- spar, such as barite, calcite, and fluorite. It is correct to call the latter "fluorspar." There is a true barium feldspar, but it is rare and of no present economic importance. What is recognized as feldspar or "spar" by present producers and consumers consists of three silicate minerals which, if pure, would have the formu- las KAISi,O, (microcline or orthoclase), NaAlSi,O, (albite), and CaAl,Si,O, (anorthite). These are almost never found in pure form in nature, but occur together in great abundance in a three-component system. A considerable number of different combined ratios of these three exists, with the exception that isomorphism between potassium spar and calcium spar is very limited. User specifications for feldspar products are largely built around the prevalent naturally occurring ratios. Pas- sages following will refer to "K-spar," "Na- spar," or "Ca-spar." Nomenclature and Descriptive Terms Relating to both the mineralogy and the economics of feldspar are certain terms whose coverage it is useful to specify. Commercially, aplite is a feldspathic rock mined and beneficiated in two locations in Virginia, in which both titanium and feldspar minerals are present-the latter now being the major, if not the only, economic product. Technically, the term aplite when applied to this rock is of questionable accuracy. But, in light of accepted commercial usage, the term will be here used to designate it. Regarding the Virginia rock, Ross (1941) is cited.

Jan 1, 1975

By Denis Yeung, B. H. G. Brady

A hybrid finite element-boundary element code with eight noded isoparametric finite elements and three noded boundary elements is described for plane strain and linear isotropic elasticity. In the direct formulation of the Boundary Flement Method, quadratic variation of geometry and displacements, and linear variation of tractions with respect to the element intrinsic coordinates are used. The boundary element region is treated as a "super-element" in the finite element sense.

Jan 1, 1982

By R. N. Kust, J. C. Agarwal, H. E. Barner, N. Beecher, D. S. Davies

Kennecott Copper Corp. has developed a new hydro-metallurgical process for extracting nickel, copper, cobalt and molybdenum from manganese nodules. This process (KCC Cuprion Process) utilizes a reduction leach operating at atmospheric pressure in the temperature range of 45°C to 50°C and has been successfully demonstrated in a continuous Pilot plant processing 350 kg/d of nodule ore. The chemistry, basic flowsheet and operating characteristics are presented and discussed.

Jan 12, 1979

By N. A. Tiner, Saara Asunmaa

The early stages of nucleation of vacuunz-deposited gold coatings on electropolished surfaces of pure nickel and binary alloys of Ni-A1 and Ni-Ti have been studied, employing carefully controlled temperature and vacuum conditions. The preferential nucleation of gold on slip-plane edges on the crystal surfaces gave rise to a very pronounced decoration effect which was used in studying the morphology of the pain boundaries, etch pits, and slip planes on crystal faces. Characteristic surface patterns were observed with local dimensional variations. Most pronounced geometric patterns were ohserved in the pain boundaries of nickel and on the crystal faces of Ni-A1 alloy. The nucleation behauior of gold indicates contamination on the Ni-T1 alloy and the getter properties of titanium are presented as a tentative interpretation for the detected contamination. The markings and imperfections on cleavage surfaces of crystals have long been observed by optical microscopy.1,2 Surface-replica techniques are also used to detect the smallest steps and structural details on crystal surfaces by electron microscopy. Recently, Bassett3-5 and Sella, Conjeaud, and Trillat 6 have shown that, when gold is deposited onto a rocksalt cleavage surface, there is preferential nucleation at steps and slip-plane edges on the crystal surface. This gives rise to a very pronounced decoration effect which is invaluable for revealing the lattice steps on a cleavage surface. According to Bassett,3 gold atoms arriving during vacuum evaporation at the crystal surface have a certain mobility on the surface after arrival, particularly at elevated temperature. If a significant

Jan 1, 1964

By Bunting S. Crocker

DISCUSSION Fred C. Bond (Allis-Chalmers Manufacturing Co., Milwaukee)—This is a very complete description of the screened ore fine grinding installation at Lake Shore. The only important data which might be desired are the operating screen analyses and power consumption in each stage. The statement that the energy consumption, or kw-hr per ton, remains constant for all mill diameters is of great interest, but the opinion is widely held that the kw-hr per ton decreases as the mill diameter increases. More definite test work is needed to establish this point. Screened ore fine minding has been successful on hard Lake Shore ore &d on about equally hard South African Rand ore. However, it is still not determined whether it would be successful on ores of average or less than average hardness. It is possible that with softer ores the consumption of ore pebbles might be exceedingly high, or might even exceed the available supply. Also, the softer feed might result in a rapid buildup of harmful intermediate sizes in the mill circuit. These factors can be determined only by a full scale or long pilot mill test. In any case the Lake Shore staff is to be congratulated for this pioneering work. Bunting. S. Crocker (author's reply)—As requested, the operating screen analyses and Bower consumption for each of the four stages of pebble milling are given, see Table XII. The fist three stages are in series circuit; the last stage is in closed circuit. The primary circuit had rock feed averaging 124 g per piece and the final stages rock feed weighing 63 g. The intermediate stages had mixtures of the two. Regarding Mr. Bond's statement that "the opinion is widely held that the kw-hr per ton decreases as the mill diameter increases," I would say that I have frequently been told this but have never yet been shown any evidence or seen any evidence published that would prove this statement. It may be true that some of the big mills recently installed have mechanical power savers such as micarta bearings and better lubrication, but as far as the power consumed inside the mill is concerned, we at Lake Shore think that it varies as D2 .", and that is all. We published extensive information on this point in our 1939 paper. Recently Mr. Banks at Consolidated published the figures on his 10 ft 8 in. x 12 ft 0 in. rod mill. As reported in this discussion by the writer: we calculated the power necessary to run this mill based on our 7x6-ft rod mill to within 1 pct of the actual power reported by Mr.

Jan 1, 1953

By Bunting S. Crocker

DISCUSSION Fred C. Bond (Allis-Chalmers Manufacturing Co., Milwaukee)—This is a very complete description of the screened ore fine grinding installation at Lake Shore. The only important data which might be desired are the operating screen analyses and power consumption in each stage. The statement that the energy consumption, or kw-hr per ton, remains constant for all mill diameters is of great interest, but the opinion is widely held that the kw-hr per ton decreases as the mill diameter increases. More definite test work is needed to establish this point. Screened ore fine minding has been successful on hard Lake Shore ore &d on about equally hard South African Rand ore. However, it is still not determined whether it would be successful on ores of average or less than average hardness. It is possible that with softer ores the consumption of ore pebbles might be exceedingly high, or might even exceed the available supply. Also, the softer feed might result in a rapid buildup of harmful intermediate sizes in the mill circuit. These factors can be determined only by a full scale or long pilot mill test. In any case the Lake Shore staff is to be congratulated for this pioneering work. Bunting. S. Crocker (author's reply)—As requested, the operating screen analyses and Bower consumption for each of the four stages of pebble milling are given, see Table XII. The fist three stages are in series circuit; the last stage is in closed circuit. The primary circuit had rock feed averaging 124 g per piece and the final stages rock feed weighing 63 g. The intermediate stages had mixtures of the two. Regarding Mr. Bond's statement that "the opinion is widely held that the kw-hr per ton decreases as the mill diameter increases," I would say that I have frequently been told this but have never yet been shown any evidence or seen any evidence published that would prove this statement. It may be true that some of the big mills recently installed have mechanical power savers such as micarta bearings and better lubrication, but as far as the power consumed inside the mill is concerned, we at Lake Shore think that it varies as D2 .", and that is all. We published extensive information on this point in our 1939 paper. Recently Mr. Banks at Consolidated published the figures on his 10 ft 8 in. x 12 ft 0 in. rod mill. As reported in this discussion by the writer: we calculated the power necessary to run this mill based on our 7x6-ft rod mill to within 1 pct of the actual power reported by Mr.

Jan 1, 1953