Search Documents

By C. Goldberg, R. H. Wynne

WHEN using an optical goniometer to determine crystal orientation' it is advantageous to use a preferential etchant so that the etch pits have plane faces which are parallel to crystallographic planes, all of which are of the same "form." "Westinghouse Silver Etch" (WAg), a preferential etch for germanium, is made up as follows: 40 ml of 49.7 pct hydrofluoric acid, 20 ml of 70.7 pct nitric acid, and 40 ml of distilled water containing 2.0 g of silver nitrate. Examination of metallographs of WAg etched surfaces (Fig. 1, for example) indicates that, regardless of crystal orientation, the faces of the etch pits are (111) surfaces. Optical goniometer examination of these WAg etched surfaces also indicates that the faces of the etch pits are (111) surfaces, i.e., all bright reflections are from (111) planes. When using an optical goniometer of the type described by Barrett,' not only (111) reflections from a WAg etched germanium surface but also other reflections of lower intensity will be observed. These latter reflections can cause confusion. We have used an optical goniometer made from a war surplus astrocompass and a galvanometer lamp. The reflections are observed by using the goniometer in a darkened room and letting the reflected light be in- cident upon a piece of white paper. The resulting decrease of goniometer sensitivity enables (111) reflections only to be observed. This in turn permits the crystal orientation to be determined in a matter of minutes, since only two measurements are necessary. The authors wish to acknowledge the help received from R. E. Davis who assisted in making the metallographs and aided the authors in the interpretation of the metallographs.

Jan 1, 1954

By W. L. Grose, J. E. Nealy

A device developed by the U.S. Bureau of Mines for the detection and quenching of coal mine explosions suffers from the inability to discriminate between the light emitted from hydrocarbon combustion and that emitted by electrical sparks and miner's cap lamps1. Since the quenchant device is activated by an internal explosive charge, the possibility of serious injury to nearby personnel demands a detector which can reject false signals. Described herein is a detector which can provide a rapid response signal upon the emission of radiation from hydrocarbon combustion and concurrently reject spurious signals from such sources as sparks and cap lamps. It was suggested that a detector might be developed to operate on the principle of monitoring the radiation intensity emitted from two separate spectral regions and ratioing the intensities2. A series of experiments was conducted for combustion of methane-air mixtures which demonstrate the ability of such a detector to discriminate between combustion and spurious signals. Experimental Apparatus A cylindrical (3.8 in. diam by 12 in.) stainless-steel shock tube test section was used as a combustion chamber. The test section was equipped with quartz windows (2 in. diam) on either side, a piezoelectric pressure transducer, and two steel electrodes. A 10-kv capacitor discharged across the electrodes provided a submicrosecond duration spark to ignite the gas mixture within. The desired partial pressures of methane and air were obtained by using a Wallace and Tiernan 0-800 mm Hg pressure gauge with which pressures could be determined to an accuracy of % mm Hg. All tests were conducted with a total pressure of 1 atm in the chamber. To

Jan 1, 1972

By K. R. Grube, D. N. Williams

It is often desirable to perform fatigue studies at relatively high strains and at low strain rates. A low-cost fatigue machine has been constructed for this purpose which has proven quite versatile. This machine is based on the principle of repeated bending of a strip sample over a shaped mandrel. A photograph of a group of fatigue tests in progress is shown in Fig. 1. The test sample is held in place between two shaped mandrels having a flat at their base to grip the sample firmly. A cam-driven loading frame is used to bend the sample alternately over each mandrel. The sample slides freely in this frame and is held in place by a light spring to accommodate increases in sample length. The pivot point for the loading frame is selected so as to minimize movement at the loading point during operation. The number of cycles to failure is recorded by a rachet counter which is kept in operation by a series electrical connection through the sample and is operated by the drive cam. The maximum strain imposed at the sample surface on bending from one mandrel to the other is readily calculated from the relationship, where t is the sample thickness and r is the radius of curvature of the mandrels. The rate of straining can be controlled by control of the cam speed. The device as shown in Fig. 1 is set up to run six samples at ambient temperature. A much larger number of samples can be run at one time without difficulty. ALSO-, by slight realignment of the components the mandrel unit can be enclosed in a separate chamber permitting control of test temperature and environment. This permits a variety of fatigue and corrosion fatigue problems to be studied.

Jan 1, 1963

By J. E. Lawver, B. J. Clingan, R. E. Snow

Response surface methodology is a well-known and powerful technique for determining optimum conditions in flotation systems. One disadvantage is the onerous task of the numerical calculations and curve plotting. This paper describes a system in which the investigator simply selects the range of several flotation variables after which the design of the experiment, data analysis, generation of response surface equations, and response surface plots are automatically carried out using a digital computer and a computer-driven curve plotter. Several typical response surfaces of important variables in phosphate flotation are presented as examples.

Jan 8, 1979

Mounting pressures to increase efficiency and yield, conserve energy, or minimize pollution have all taken their toll on the minerals industry. As management and technical personnel take a harder look at their operations for ways to shave cents off operating costs or to squeeze a bit more productivity out of existing equipment, instrumentation often comes up as the most effective answer. When Amax Lead installed an automatic grind control system in its Buick mill, ore throughput increased by 3 to 5%. Mill operators calculate that the initial investment is returned to them several times annually.

Jan 2, 1978

THE bellows are important and necessary agents in most melting processes. In addition to seeing that these have sufficient soft cloth, extend far and wide, and are of good design, including good valves and good long tubes, and that they cannot break and lose the air received, it is very important to give attention to their installation so that they may easily effect their purpose. Therefore I now wish to proceed by noting some common devices for moving them, both with water and with man power, so that you may make use of them as the need arises.

Jan 1, 1942

By V. D. Perry

Mineralized breccia pipes, because of their widespread occurrence and close structural relations to some of the world's great ore bodies, are objects of unusual interest for mining engineers and geologists. The literature contains many references to them, but it is questionable whether their genetic significance and economic importance have been sufficiently emphasized. The purpose here is to stress these features, relating them to the field facts, for the particular benefit of younger generations of geologists who, confronted with and sometimes confused by the growing flood of geochemical, geophysical, and other specialized research approaches, may be reassured that mappable field relations remain a foremost guide to a better understanding of ore deposits. A mineralized breccia pipe is a pre-mineral, breccia structure which has controlled the circulation and deposition of subsequently introduced mineralization. It is composed of relatively rotated angular or rounded rock fragments, set in a mineralized matrix. A pipe in plan outline may be circular, oval or approach polygonal form, with a steep to vertical axis proportionately much greater than its horizontal dimensions. The pipe is a steeply plunging, chimneylike mass of brecciated rock cemented with later minerals. Rock breaks in a variety of ways and complete fragmentation often occurs without rotation of individual pieces. A finely broken rock mass may fit into a tight jig-saw pattern, each fragment having mutually concordant boundaries with its neighbors. The result is a stockwork of innumerable reticulating cracks that, once cemented by mineralization, forms a complicated intersecting network of individually insignificant but collectively important seams and veinlets. Stockwork fracturing among its many forms takes the shape of domes of subsidence, fracture pipes, and related peripheral zones around and over breccia columns, or a combination of any of these structures. The significance of the mineralized breccia pipe is that it represents the extreme or climactic expression of a structural type which has a variety of mutations including subsidence domes, fracture pipes, and other stockwork zones all with related ancestry and similar to dissimilar characteristics. These allied and associated structures hold an answer to the fundamental question of the origin of many important ore deposits. CANANEA-TYPE LOCALITY FOR BRECCIA PIPES The Cananea district is characterized by an unusual development of mineralized breccia pipes. It is an important copper producer located in Sonora, Mexico, a short distance southwest of Bisbee, Arizona, and at the southerly limit of the great porphyry copper belt of the southwestern U.S. Cananea's rocks consist of Paleozoic quartzite and limestone capped unconformably by a thick series of volcanics including andesitic flows, tuffs, and agglomerates. These rocks have been intruded by a deep-seated granite with related basic and acid differentiates including dikes and plugs of quartz mon-zonite porphyry. Mineralization coincides with a northwesterly trending belt of these intrusives which break upward into and through the sedimentary-volcanic rock sequence. The district has weakly defined tectonic alignments in a northwesterly direction with subordinate intersecting fracture elements, but lacks important faulting or fissuring to provide throughgoing avenues for the upward circulation of mineralizing fluids. Thus, as will be discussed in subsequent paragraphs, the alternate way in which late magmatic and hydro-thermal derivatives of the parent magma reached the near-surface zone was by excavating their own breccia pipe channelways. There are numerous stages of breccia pipe development, related both in time and space to magmatic activity. A compilation of similarities and differences in various pipes suggests that proximity or remoteness of a demonstrable or inferred magmatic source provides an orderly genetic basis for describing the following representative types. Cananea Duluth Type: There are no intrusive rocks within or close to the Cananea Duluth pipe; therefore, the existence of any deep-seated magma that may have been related to its formation must be inferred. The structure is an oval-shaped ring 1200 x 300 ft in plan dimensions, cutting steeply across low angle, bedded tuffs, and other volcanics; it has been developed by drill holes to a depth of 2000 ft below the surface. The ore follows the periphery of the pipe and is composed of intensely brecciated rock which is cemented by minor galena, sphalerite, chalcopyrite, quartz, carbonates, and adularia. There is a definite vertical zoning of sulfides with less galena, continuing sphalerite, and increasing chalcopyrite at deeper levels. Within the interior of the ore ring, the brecciation becomes progressively weaker and coarser, the whole indicating relatively gentle slumping with broken, thin tuff beds pre-

Jan 1, 1961

By P. Bouéry

This account of a contrivance which has been found serviceable in practice may be of interest to engineers, and especially to those engaged in hydraulic mining. In that process, one feature which seems at first sight to possess little significance, is highly important in its effects—namely, the regular supply of water to the " giants." The chief condition of this regularity is an even flow in the pipe-line from the penstock to the nozzle.' This, of course, requires that the penstock be kept full. Any considerable surplus of water, overflowing at the penstock, is a simple waste, unless it be otherwise utilized in the sluices. At all events, it does not affect the delivery of the nozzles. But a deficiency at the penstock may admit air into the pipe; and this may produce hydraulic recoil, injuring the line by incessant vibrations, giving rise to leaks, and even to blow-outs, and (when a partial vacuum exists at the time of the fracture) the collapse of the pipe. An accident of this sort in our main pipe-line, occasioned partly by a settling of the ground and partly by the presence of air in the pipe, led to the employment of the device here described. The line referred to is made of 30-in. pipe, successively reduced to 18 and 15 in. in diameter, for the supply of two giants. By reason of the causes above mentioned, the 30-in. pipe burst more than 1,400 ft. from the penstock, and, despite the air-valve, the 30-in. pipe was collapsed to such a degree that one length of it, next to the penstock, was squeezed together and positively swallowed by the main pipe, through which it traveled for 750 ft., piercing through a short elbow on the way. This remarkable result was undoubtedly the effect of the vacuum suddenly produced when the pipe burst.

Jan 1, 1907

By P. E. Demmler

Phosphorus combines with copper in various proportions, forming true alloys, some of which are of commercial importance. These materials find wide application as deoxidizers and as a means of introducing phosphorus into other alloys, as in phosphor-bronze. Phosphor-coppers containing 10 and 15 per cent. of phosphorus are the commercial grades that are most generally offered. Each has certain advantages when used in making other alloys. The 10 per cent, grade of phosphor-copper has an advantage over the 15 per cent. in that it has a much lower melting point and can be prepared by certain methods with a much lower loss in phosphorus. The 15 per cent. grade has the advantage of lower freight rates per unit of phosphorus and, by the method to be described, a uniform product can be prepared with practically no loss of phosphorus. Alloys of copper and phosphorus containing any desired percentage of phosphorus lower than 15 per cent. can be prepared by melting together the requisite amounts of copper and 15 per cent. phosphor-copper. Processes for making phosphor-copper may be divided into two classes as follows: (1) Those depending on the smelting of phosphate rock or superphosphate of calcium with copper or copper-bearing materials, and coal or other carbonaceous material; (2) those depending on the direct combination of metallic copper and elemental phosphorus. A number of formulas for preparing phosphor-copper according to the first method have been published. The Metal Industry' gives the following: Superphosphate of calcium, 60 lb.; granulated copper, 30 1b.; finely powdered coal, 10 1b. Similar formulas are given by Brannt2 and others, and detail variations are covered by patents, such as those of L. A. Jeffs3 and H. A. Webster.4 Among the objections to this method of producing phosphor-copper are the large amounts of raw material and resulting slag to be handled, and the difficulty of getting a satisfactory fusion. S. Skowronski5 found that at 1300' C. (2372' F.) it was impossible to get a good fusion

Jan 1, 1921

By Joseph E Pogue

Over a period of years the writer has presented a number of studies1 on various aspects of proration, in a progressive attempt to analyze critically and constructively the economic complexities of this interesting institution, which in a decade has revolutionized the economics of oil production in the United States. In the course of the investigations leading to these papers, the changing nature of proration and the principles underlying its evolution have gradually become clear, so that it is now possible to depart from the analytical method and to construct a synthesis of the steps that, if furthered by the industry, should carry proration past the economic hazards that still surround it to the goal of maximizing the value of the petroleum resource to the industry and the public alike. Nature of Proration Proration literally means the allocation of demand among competing producers on a pro rata basis, but the term now carries a much broader significance for it is employed to describe the entire process by which the production of crude oil in the United States is regulated. There is naturally much confusion of thought on the subject, for proration is an evolving system of control based upon principles of conservation and equity and embracing a body of practices that are tending to adjust themselves to the needs of the situation but are subjected to varying and divergent influences in the process. As it is now constituted, proration is a planned production measure designed to prevent waste, insure ratable takings, and balance supply and demand. The procedure is administered by State regulatory bodies through use of the police power of the States under authority of State conservation laws; the practice is supported by a considerable degree of voluntary conformance on the part of operators; and the Federal Government has accorded its cooperation by providing advisory quotas, circumscribing imports, checking movements of hot

Jan 1, 1939

By Eugene A. Stephenson, Leon J. Pepperberg

The natural gas industry is essentially a byproduct of the oil industry. When first discovered the gas was usually regarded as a nuisance, and even when found immediately associated with oil, or suspected to be so, it was customary to blow it freely into the air, in the hope that gas would shortly be replaced by a flow of oil. The early methods of production,' transportation, and utilization were neither economical nor efficient; the chief value of gas was based on its use as a fuel, with no regard to (1) its effect. upon the oil with which it was associated, (2) its importance as a lifting agent, or (3) to its possibilities for the manufacture of byproducts. The spread of scientific research among major gas and oil companies, manufacturers, and academic groups, has gradually brought recognition of the fact that many of the technical problems bearing on production, transportation and utilization are common to both the gas and the oil industry. A few of the problems that have received serious study, and from which highly gratifying results have been obtained, are: (1) gas measurement, (2) oil well and gas well capacity tests, (3) elimination of field waste, (4) design of pipe lines and compressor stations, (5) extraction of constituents which might interfere with the normal flow of gas through the line, (6) control of reservoir pressure, (7) estimation of reserves of both oil and gas, (8) control of water encroachment, (9) measurement of factors which influence fluid movement through sands, (10) solubility of gases in oils, (11) effect of dissolved gases upon the properties of the solution. These investigations have demonstrated that almost every problem relating to oil production also involves some phase of natural gas engineering. During the past 15 years the use of experimental methods for the discovery and measurement of obscure, influencing factors, which cannot be determined purely by hydrodynamic or thermodynamic analyses, have contributed much towards the progress made in solving the problems of the oil and gas industries. Most of the experimental work on

Jan 1, 1934

By Joseph E. Pogue

Over a period of years the writer has presented a number of studies1 on various aspects of proration, in a progressive attempt to analyze critically and constructively the economic complexities of this interesting institution, which in a decade has revolutionized the economics of oil production in the United States. In the course of the investigations leading to these papers, the changing nature of proration and the principles underlying its evolution have gradually become clear, so that it is now possible to depart from the analytical method and to construct a synthesis of the steps that, if furthered by the industry, should carry proration past the economic hazards that still surround it to the goal of maximizing the value of the petroleum resource to the industry and the public alike. Nature of Proration Proration literally means the allocation of demand among competing producers on a pro rata basis, but the term now carries a much broader significance for it is employed to describe the entire process by which the production of crude oil in the United States is regulated. There is naturally much confusion of thought on the subject, for proration is an evolving system of control based upon principles of conservation and equity and embracing a body of practices that are tending to adjust themselves to the needs of the situation but are subjected to varying and divergent influences in the process. As it is now constituted, proration is a planned production measure designed to prevent waste, insure ratable takings, and balance supply and demand. The procedure is administered by State regulatory bodies through use of the police power of the States under authority of State conservation laws; the practice is supported by a considerable degree of voluntary conformance on the part of operators; and the Federal Government has accorded its cooperation by providing advisory quotas, circumscribing imports, checking movements of hot

Jan 1, 1939

Much has been written in the past about the non- cataracting ball mill as typified by the installations of the Tennessee Copper Co. at Copperhill and the three units of the Cleveland-Cliffs Iron Co. in its Humboldt and Republic mills. Because no direct comparisons are available from the Cleveland-Cliffs plants and because the published data of Tennessee Copper Co.'s London mill covered a period of development over several years, it has been difficult for engineers to grasp the full significance of the non-cataracting economics.

Jan 11, 1957

By R. B. Falk, F. E. Luborsky

Small iron particles in mercury pow by diffusion of iron atoms through the mercury. Iron particles, with diameters about 200Å, have been stopped from gvowing in size, even up to the boiling point of mercury, by the addition of a third metal. The metal additives were classified according to whether they produced 1) negligible inhibition, 2) some inhibition, or 3) marked inhibition of the growth rate. Metal additives which resulted in a marked inhibition of iron-particle growth form a stable monolayer on the iron particles. Only those metals which may form compounds with iron showed this pronounced effect. The one exception was manganese. Metal additives which resulted in no inhibition of growth, showed no evidence for adsorption and could not form compounds with iron. None of the added metals, even those which strongly inhibited particle gvowth and thus had adsorbed on the particle surface, actually formed any compounds with iron at room temperature at the concentrations required for complete inhibition of growth. ThE stabilization of the size and shape of metallic particles dispersed in liquid metals has important technological implications in "homogeneous" nuclear reactor systems and in elongated particle magnets and is directly related to the problem of corrosion by liquid metals. Growth in these par-ticulate systems may occur by diffusion of atoms from surfaces of high energy, corresponding to a small radius of curvature, to surfaces of low energy or large radius of curvature. Thus, small particles dissolve and large particles grow to increase the average diameter of the particles. reenwood' has analyzed this diffusional growth of a system of particles containing a distribution of sizes and has obtained reasonable agreement with data on the growth of uranium particles in liquid sodium and UPb3 particles in liquid lead. Greenwood concluded from his analysis that the chief factors promoting stability of dispersed particles growing by a diffusion mechanism are large mean radius, high density, and low molecular weight with low values of the solute diffusion coefficient, the solubility, and the interfacial tension. In the case of elongated particle magnets the system of interest is that of iron particles dis- persed in mercury. Previous work,2 concerned with "spherical" particles in mercury, has indicated a diffusional growth mechanism similar to that discussed by Greenwood. It has also been shown3'4 that the addition of certain metals to Fe-Hg dispersions results in the formation of a monatomic layer of adsorbed atoms on the iron particles. In this paper we will show that this adsorbed layer provides the decrease in the iron-atom flux through the mercury necessary for size stabilization. The general features of the stabilization of the iron particles in mercury through the formation of this "coating", with many different metals, will be described. EXPERIMENTAL RESULTS Iron particles in mercury were prepared by elec-trodeposition,2, 4 and measurements2, 4 of coercive force HCi) and saturation induction (Is) were used to follow changes in size and composition during thermal aging in the mercury in the presence of relatively small amounts of an added metal. In Fig. 1 is plotted the aging behavior of spherical particle samples in the presence of some of the added metals to be discussed. The iron particles have an initial average diameter of 180Å. Each sample was aged for 20 min at each temperature in succession in the presence of a twofold to threefold excess of added metal over that required to form a monolayer on the iron particles. These are the same samples used previously3 to study the adsorp-

Jan 1, 1965

By H. A. McKinstry, F. F. Lange

A vector analysis of orientating single crystals using the Laue back-reflection X-ray technique is given. Briefly, the analysis involves using a few data taken from a Laue photography and defining the crystal co- ordinate axes in a reference coordinate system. After a few matrix multiplications, the proper goniometer angles can then be determined to orient the crystal coincident with the reference frame. This analysis is easily programed for a digital computer to provide a fast, precise, and efficient method of orienting many crystals which are identical. The general procedure is as follows. The crystal is mounted on a goniometer. Laue photographs are taken until an array of diffraction spots is observed that includes a Laue spot that represents a rotational axis of symmetry. The rotation angles of goniometer are recorded. These angles are defined as positive for a counterclockwise rotation. When the axis of symmetry is located on the Laue photograph, the crystal coordinate axes can be defined in the reference coordinate system* as follows. Two Laue spots are chosen, one of which corresponds to the rotational axis of symmetry and the other to a set of planes whose zone axis is a known crystallographic direction and normal to the rotation axis of symmetry. The Laue spots are used to determine these two crystal directions in the reference coordinate frame. This is done by placing the Laue photograph on a sheet of polar coordinate graph paper and determining the polar coordinates (r, o) of these two diffraction spots in the reference coordinate frame. Their third coordinate is the distance between the crystal and the film (-D). The coordinates Xni of the two crystal directions Nn, (n = 1, 2) in the reference frame are then calculated by the following equations: Xn1 = -D X2n = Ancos on X3n = A, sin on where -tan- 1 rn/D An =Dtan(tan-1rp/D/2) By taking the proper cross products of these two directions (normalized to unit vectors), the crystal coordinate axes 3 (i = 1, 2, 3) can be determined in the reference frame. This is illustrated in Fig. 1. The next step is to determine the relation between

Jan 1, 1969

By H. R. Hanley, D. F. Walsh, C. Y. Clayton

Lead-refining practice at the Bunker Hill differs to some extent from that of other United States refineries using the Parkes process, in that the Bunker Hill has reverted to a custom used years ago of making two kinds of skims, or crusts, in the desilverizing kettles. Also, this was the first refinery to adopt the liquation process for silver skims as developed in Australia. Both of these ideas were brought to the attention of the operator by H. S. J. Sommerset, in the summer of 1924, while he was visiting metallurgical plants in the United States, when he was general superintendent of the Broken Hill Associated Smelters Pty., Ltd., of Port Pirie, South Australia. Since Mr. Sommerset's visit, United States patents on the liquation process have been issued to George Kenneth Williams, of Port Pirie, South Australia. At the Bunker Hill, the lead bullion is conveyed from the blast furnaces to the refinery in brick-lined cast-steel pots, each having a capacity of 5 tons, by a 20-ton electric crane, to which is suspended a Fairbanks-Morse suspension-type scale on which the gross, tare and net weights are obtained. The bullion is poured from the small bullion pots into either one of two kettles of 105 tons capacity, and when a kettle is entirely filled the heavy dross is removed by skimming it into a 5-ton pot suspended by the crane. The crane operator becomes proficient in the manipulation and a kettle is skimmed in a very short time. After the kettle is skimmed clean the bullion is pumped to a kettle of the same size alongside, where the bullion is cooled until it has almost frozen. By using two kettles for the drossing operation, one to accumulate the bullion where the heavy dross is removed, and then pumping to a clean kettle comparatively free of hangings, etc., it is possible to reduce the copper content much lower than if only one kettle is used in the operation. The average yearly analysis of bullion is given in Table 1. During July, August, September, and October, when a considerable quantity of high-grade silver ore from the Yukon Territory is smelted,

Jan 1, 1930

By L. L. Swift

AT the present time there are four base metals being used for automotive bearing alloys. Of course there are numerous variations in the amounts of alloying elements added to each base metal and nearly all of these alloys have the conventional, if not classical, duplex structure; that is, they are composed of a hard constituent embedded in a soft matrix. The well-known theory is that the former will wear well, while the latter will be plastic enough to allow the bearing to be broken in and conform to the contours of the shaft. The requirements of the modern bearing have been most aptly described by W. M. Corse: In order to meet the engineering demands of today a good bearing metal must be able to carry the weight of the shaft and stand up under steady or suddenly applied loads, or even blows in some types of service. A certain amount of plasticity is desired to compensate for minute irregularities in the shaft or bearing surface, and to permit yielding, thereby avoiding dangerous stresses in bearing and shaft and preventing overheating and rapid wear of parts. Less plasticity is required in a bearing metal if the surfaces of bearings and journals are machined accurately, aligned, and kept in alignment. It is desirable, of course, that a bearing metal have a low coefficient of friction. Under most operating conditions the friction depends on the unit pressure of the bearing, the speed, the temperature, and the properties of the lubricant. A good bearing metal must have a low rate of wear to reduce the necessity for frequent replacements, and adjustment of the bearings. It must wear more rapidly, however, than the journal or shaft running on it, because replacement of the journal or shaft is more difficult and costly than replacement of the hearing., The hardness of, the bearing alloy is a property closely related to several of the foregoing. With a duplex microstructure, the measurement of hardness with any of the usual commercial devices means little. The Bierbaum method of measuring the hardness of the individual constituents was developed to, fill this need. MICROCHARACTER The Bierbaum microcharacter2.3 measures the scratch-hardness of a solid by pulling a weighted diamond point over the surface. The diamond point is ground. so that it is the corner of a cube, and mounted

Jan 1, 1938

By P. A. Fisher, J. B. Wilson, D. J. Whitehead, C. J. P. Ball, A. C. Jessup

The properties of a new magnesium alloy ZT1 containing 3.0 pct Th, 2.5 pct Zn, 0.7 pct Zr are described. The alloy possesses good creep and fatigue resistance up to 650°F, is free from microporosity, and is readily sand-cast. ZT1 is shown to be superior to zinc-free Mg-Th-Zr alloys. THE advent of the jet engine created a demand for a light sand-casting alloy capable of being cast into large complex shapes and capable of resisting creep at temperatures up to 500°F. This demand has been largely met by alloys of the magnesium-cerium mischmetal-zirconium types, containing about 3 pct Ce mischmetal and 0.7 pct Zr, typified by Elektron magnesium alloys MCZ and ZREI, the latter alloy also having a zinc addition of 2.5 pct. These alloys utilize the valuable properties at elevated temperatures conferred by the addition of rare earth metals to magnesium, a fact which has been known for many years and discussed by several investigators.1-1 Murphy and Payne8 showed that the addition of the powerful grain-refining element zirconium to Mg-Ce mischmetal alloys produced alloys with attractive room temperature properties combined with good creep properties and castability. With the increasing power of modern jet engines the temperatures to which some of the magnesium parts are subject are likely to exceed the safe working range of the cerium-mischmetal-containing alloys, and at the beginning of the research considerable interest had been shown by aeroplane engine designers in a magnesium sand-casting alloy suitable for service at higher temperatures, e.g., 600°F and above. At an early stage in the development of this type of alloy a check on the fatigue properties at elevated temperatures indicated that, since the fatigue limit even at 108 eversals was appreciably higher than any permissible creep stress, the main emphasis of the research could be concentrated on creep behavior. The primary aim in developing the new alloy has therefore been to attain maximum creep resistance; but due consideration has also been given to other important properties such as castability, tensile strength, and cost. It is by now well established that it is not possible to correlate creep strength with other short time mechanical properties such as are obtained in tensile

Jan 1, 1954

By Joseph Mac Donald

Stripped of its romantic possibilities, mining is a commercial business, carried on for the profit there is in it; and the business of the manager, in its ultimate analysis, is to make the profit as large as possible. The general manager of a mining company should keep himself personally familiar with all the details of its operations. If he fails to do so, chaos results, labor becomes inefficient, costs go up, and profits go down. Nowhere is this emphasized more than in Mexico. If the mining operations are extensive and complex, involving, besides the work of mining the ore, its transportation and treatment by various milling operations, and the marketing of the products, the business, to be carried on properly, must be

Jan 1, 1909

By J. S. Wakeman

The techniques of testing the physical properties of green pellets produced in a batch balling test are described. It has been found that these physical properties, i.e. drop resistance, wet compressive strength, and plastic deformation under load, are generally related to the moisture content of the wet balls. A "criterion" method of analyzing data from a series of batch tests is discussed. This method facilitates the comparison of results of various test series. A time-sharing computer program, which correlates the test data from a batch series, generates the "criterion" values for subsequent comparison and analysis, and produces X, Y plots of the various moisture-strength relationships, is presented. Examples of computer output and use of the "criterion" evaluation method are given.

Jan 1, 1973