Search Documents

By E. R. Parker, C. F. Riisness

That grain size has a great effect on the mechanical properties of metals has been recognized for a long time. Bassett and Davis1 in 1919 did excellent work in determining the effect of grain size on the hardness of brass. About the same time Jeffries2 and Sykes3 ascertained the effect of grain size on the strength and ductility of several metals at temperatures ranging from 80°K. to their melting points. When creep was recognized as an important property of metals, those engaged in the study of this property tried to determine the effect of grain size4-9 on creep rates. Unfortunately, most of the investigations were conducted on only two grain sizes, often designated simply as "fine" and "coarse." It is well known that at high temperatures coarse-grained test bars creep less than fine-grained bars. The relation between grain size and size of test bar, however, has been frequently overlooked. In his early work, Jeffries2 showed that the number of grains in the cross section has a more important influence on the properties of the material than the actual grain size. More recently Hanson and Sandfordl0 and Pell-Walpole,ll in their measurements of the creep and tensile properties of tin, tested a wide range of grain sizes and correlated the grain size with the strength. Hanson9 later established the relation between the number of grains in the cross section and the creep rate. At high temperatures, generally a coarsegrained structure is considered superior in creep to a fine-grained structure, but it is evident that for a given bar size continuously increasing the grain size will

Jan 1, 1944

By Paul Weir

BLEACHING clays have been used extensively in the oil-refining industries for a number of years. Their use in water purification is relatively recent and less extensive. They are frequently classified as (1) those naturally active and (2) those active after artificial activation with acid. Fuller's earths fall within the general group of bleaching clays and gradually the commercial term "fuller's earth" has been applied to natural clays originating, for the most part, in the south-eastern section of the United States. Bentonitic clays are usually classed as activable and are prevalent in the southwestern section of the United States.1 Bleaching clays vary considerably in chemical and physical properties throughout the country, or even in different parts of one deposit (Table 1). TABLE 1.-Physical and Chemical Composition of Different Types of Clays Composition, Per Cent Constituents and Properties Bentonite Fuller's Mud Clay (Wyoming) Earth (P Peak)' (Alluvial) Silica (SiO2) 60.0 69.6 61.67 Alumina (Al203) 19.0 14.3 20.34 Ferric oxide (Fe203) 2.8 3.90 7.70 Titanium oxide (Ti02) 0.13 0.70 1.01 Lime (CaO) 0.5 0.80 0.00 Magnesia (MgO) 2.0 1.00 0.24 Soda (Na2O) 2.4 0.40 0.31 Ignition loss 4.7 6.77 8.51 Moisture content 8.0 10.0 20.0 Isoelectric point, pH 9.2 9.2 6.5 Average swelling volume 15.0 0.0 0.0 Weight per cubic foot, lb 55.0 40.0 65.0 Material passing 200-mesh sieve, per cent 90.0 85.0 50.0

Jan 1, 1939

By Perry Harrison

THE mixing of fine ores with fuel and burning under induced draft is called sintering in iron-ore practice and either sintering or roasting in copper and lead metallurgy. The first development of sintering was the Huntington-Heberlein process, in which fine sulfide ores mixed with fuel were charged into a pot and burned under the action of an upcast current of air introduced at the bottom of the pot. Modern development has resulted in two types of machine; the continuous Dwight-Lloyd machine, which consists of heat-resisting grates and a moving beltlike type of hearth constructed of metal, in which air is drawn downward through the bed, and the stationary Greenawalt batch process, which operates in the same manner as the Dwight-Lloyd except that the hearth is stationary. The recent rapid increase in the use of sintering has been the result of two great advances in metallurgical process-flotation and the treatment of flue dust. The Dwight-Lloyd machine is used in many plants for agglomerating flotation concentrates and at the same time reducing the sulfur content to furnace requirements and it has become standard practice to treat iron blast-furnace flue dust by either the Greenawalt or Dwight-Lloyd machine, so that it can be recharged into the furnace. The mining of low-grade magnetite iron deposits and their beneficiating by grinding and magnetic separation resulted in a fine concentrate extremely detrimental to blast-furnace practice. These concentrates are sintered and made into ideal material for blast-furnace use. Incidentally, coke savings of about 400 lb. per ton of pig are reported.

Jan 1, 1930

By Luther W. Lennox

During the last few years, one of the great problems in the milling of all ores has been that of grinding. This subject involves not merely the cost of the operation, but also the selection of the proper degree and character of grinding to yield the best metallurgical results on the given ore. Considering the diversity of machinery, one is led to wonder at the variety of grinding methods employed, even when realizing that metallurgy demands varying products. In an attempt to investigate the relative grinding resistances of a number of ores now being milled in this country and Alaska, the manage-mxitofthe Portland mills requested Samples of average mill-run of ore from various companies. The request met with a ready response, indicating the desire of all operators to gain information on the subject. The difficulties involved in this investigation were numerous, lack of time for outside problems during this strenuous period being a serious one. Also, we were unable, in the time, to obtain a correct 150-mesh screen; in the screen analyses tabulated and plotted herewith, the 150-mesh screen was used merely to protect the 200-mesh screen, not to ascertain points on the curves. The experimental grinder was a small iron tube-mill, 8 by 121/2 in., in which was placed a definite number (74) and weight (3450 gm.) of 3/4-in. steel balls, 1 Ib. water and 1 Ib. ore. To obtain uniform conditions, each ore was first crushed and screened, and from the sized products a "standard feed" was artificially prepared, the same standard being adopted for all tests in that particular series. The prepared feed was

Jan 1, 1920

By John Metz, D. E. Macdonell

The Falconbridge ore body, on the southeastern periphery of the Sudbury Basin, is definitely associated with a strong shear zone along the norite greenstone contact, in contrast to the "offset" ore bodies sometimes found in this district. To all practical intent and purpose, the dip is vertical. The ore varies in width from a few inches up to 90 ft., the average width being 15 ft. The present zone of mining operations is 6000 ft. long, 85 per cent of which develops commercial ore. The ground on the whole, and especially in the narrower widths, gives rise to reasonably strong self-supporting backs in most places, but the walls, because of strong post ore faulting on both norite and greenstone contacts, tend to be weak, and, at times, slough to a considerable extent. Obviously. then, with vertical dips, strong backs and weak sloughing walls, flat-back cut-and-fill methods are applicable to the Falconbridge ore body, and at present about 70 per cent of the stoping production is obtained in this way. The general method is described in the following pages. In actual practice, there are continual variations, as the mine staff feels that only in that way can new and better methods be developed. Source of Fill The overburden at the property consists of glacial sands and gravels, varying in depth from 00 at the outcrops, which are few and far between, to 150 ft. This condition makes for high initial cost of shaft sinking, always entailing spiling and concrete, but this extra expense is more than compensated for by the fact that the overburden is the source of very cheap fill.

Jan 1, 1946

By E. P. Chapman

In May 1957 a diamond drill hole intersected 40 ft of magnetite and chalcopyrite assaying 2.55% copper and 51.6% iron on the claims of Craigmont Mines Ltd. near Merritt, southern British Columbia. The subsequent drilling indicated the presence of a multi-million ton orebody averaging over 2% copper and 18% iron, the latter present for the most part as magnetite and specular hematite in approximately equal proportions. This orebody, although under shallow cover at its eastern extremity, did not come to the surface and the early drilling was done on the basis of strong coinciding magnetic and geochemical anomalies. After 4 ½ years of intensive exploration and development the property was put into production in September 1961. The new ultramodern concentrator has a design capacity of 4000 tpd but is consistently treating well over this amount. Production is currently coming from that portion of the deposit which is amenable to open-pit mining methods. By mid-1958 information regarding the importance of the Craigmont find became fairly wide- spread, and exploration in the Merritt area was greatly intensified. Numerous magnetic and geochemical anomalies have been tested by drilling with notable lack of success. Detailed geological studies of the deposit and of the area have been made by Government agencies and by private companies and such studies are continuing. Many types of geophysical methods have been employed over the Craigmont deposit in an effort to develop knowledge which would assist in the search for similar mineral concentrations in the environment in which it occurs. This paper will discuss the results of the various geophysical surveys in relation to geological conditions and ore outlines insofar as they are now known.

Jan 7, 1962

By G. R. Fitterer

BY means of the C-SiC thermocouple1, liquid metal temperatures have been found to vary much more than was previously supposed, and fortunately these variations can be directly associated with some of our former knowledge which combined to form the "art" of liquid-metal manipulation. COMMERCIAL DEVELOPMENT OF THIS DEVICE Several types of installations are operating in different plants. There are so many variables in steel plants in regard to operation, pro-cedure, arrangement of pouring platforms, ladles, etc., that most of the installations now in service in this country are "tailor-made"; never-theless, it is felt that satisfactory gains have been made inasmuch as each installation has indicated some effect of temperature upon the metal-lurgical operation, and has pointed the way toward technical and finan-cial benefits. In most cases, it has been necessary to accumulate the temperature data until sufficient metallurgical information is available for the drawing of conclusions. When mechanical difficulties have been eliminated, a distinct correlation of these factors has been obtained. The installations now in service. are used for the determination of temperatures in the basic open-hearth furnace prior to tapping and in ladles from both acid and basic furnaces prior to pouring. Some of the installations are in shops making the higher priced steels; others are in "tonnage shops." The errors of human element, smoke screens and emissivity corrections connected with the use of the optical pyrometer do not affect the C-SiC thermocouple readings. The accuracy of the C-SiC- thermocouple and the temperatures measured are discussed later in this paper.

Jan 1, 1936

By Leo L. Van Sambeek

An understanding of the creep and yield behavior of salt is required for the rock mechanics design aspects of solution mining. Most previous studies of salt behavior have been performed on small specimens of salt under homogeneous stress conditions; i.e., uniaxial and triaxial tests on specimens <0.002 m3. The corejacking test is a larger scale test (-0.75 m3) with inhomogeneous stress conditions that provides data on the structural response of salt. Interpretation of the responses from eight such corejacking tests provides verification of the requisite constitutive parameters required to predict salt behavior at different levels of stress and temperature. These constitutive parameters are not those studied in the usual laboratory test. Corejacking test results show almost inseparable elastic and plastic closures simultaneous with the corejack pressurization. Very rapid closure (on a relative basis) continues for a period of time after the pressurization. This rapid closure is shown to be both continuing yield deformation and creep deformation. After the period of rapid closure, the closure rate approaches a constant value. Numerical modeling of the corejack tests using a creep law containing both transient and steady-state creep functions does not provide results that agree with the responses measured in the corejack tests. Using an experimental design technique plus additional numerical modeling that includes yielding of the salt, results in identification of the significant parameters which allow agreement. The significance of the results from the study is demonstrated by comparing the postulated stability and creep response of a solution-mined cavern using the previous understanding of salt behavior and the understanding developed from this study.

Jan 1, 1985

FRIENDS of the late Charles F. Rand presented in 1930 a sum of money from which the income is available to support various phases of the work of the Institute in which Mr. Rand was so deeply interested. At present the fund amounts to $10,900. The specific terms of the deed of gift are as follows: "The fund collected to establish a memorial to the late Charles F. Rand shall be placed in the custody of the Board of Directors of the American Institute of Mining and Metallurgical Engineers, to be set up as a trust to be known as the `Charles F. Rand Foundation,&apos; the income of which shall each year be applied to a distinct purpose to be decided upon in that year by vote of the Board of Directors. This purpose shall be such as to promote the general welfare of the Institute and to constitute a permanent memorial of the usefulness of Mr. Rand, who for many years gave unstintingly of his time and talents in its service. "It shall be within the discretion of the Board of Directors to establish a medal to be known as the Charles F. Rand Memorial Medal to be awarded at such a time and under such rules as may be determined by the Board of Directors, for Distinguished Achievement in Mining Administration." The establishment of this medal was announced at the annual meeting in February, 1932, the term "mining" being defined in its broad sense to include metallurgy and petroleum. Robert Linton is chairman of the Charles F. Rand Foundation Award Committee.

Jan 1, 1942

By Webster Hodge

MALL generators and motors are required to Soperate, in some critical applications, at temperatures where cold-worked silver-bearing copper re-crystallizes. Copper containing up to 30 oz Ag per ton has been used for many years to build the highest grades of commutators and slip rings. With failure of commutators impending because silver-bearing copper cannot withstand the stresses imposed at these higher temperatures, Cr-Cu was tried as a substitute with varying degrees of success. Cr-Cu proved difficult to fabricate because a critical heat treatment was necessary to obtain sufficient ductility. Besides, its rupture strength was shown to be low at operating temperatures, its electrical conductivity lower than desired, and its cost high. Furthermore, it often contained hidden flaws. The Nippert Electric Products Co. set out to find a better material by undertaking a research project with the stated objective of providing a material suitable for commutators that would have 1) a softening temperature above 750°F (400°C), 2) a minimum electrical conductivity of 90 pct of that of pure copper, 3) a strength not less that that of cold-worked silver-bearing copper, and 4) a materials cost of not over 1.5 times the cost of copper containing 25 to 30 oz Ag per ton. No commercial alloy met these specifications. However, it was found that copper containing from 0.18 to 0.35 pct Zr could be produced quite easily in the laboratory, and promised to fulfill the major requirements noted above. Interest naturally centered in the lower part of this composition range, since such alloys gave somewhat better electrical conductivities, and were lower in

Jan 1, 1958

By A. H. Miller

THIS survey is one of the more recent tests of geophysical methods of prospecting by the Dominion Observatory and the Geological Survey of Canada, of which the purpose is to find out what application such methods may have to geological problems in Canada. The Malagash salt deposit lies on the north shore of Nova Scotia about 40 miles east of the New Brunswick boundary, and forms a part of faulted and folded Carboniferous strata. The salt beds are exposed only in the mine workings, which are about 1000 ft. deep and at one place extend for 1000 ft. along the strike. Lack of rock exposures, complicated folds, and faults make it impossible to predict the location of salt away from the mine. A survey of an area in the vicinity of the mine was therefore undertaken to find out whether the salt could be located by the torsion balance and whether its extension from the mine workings could be traced. As the gravitational effects at Malagash may be fairly typical of those at other concealed salt deposits in the Carboniferous rocks of the Maritime Provinces of Canada, the survey has a direct bearing on prospecting for other deposits. The survey was made in 1934 by A. H. Miller in collaboration with Dr. W. A. Bell, of the Geological Survey of Canada. Observations began on June 15 and were completed four months later, on Oct. 15. Definite gravitational effects including a lowering of gravity were observed over the deposit. The survey also disclosed one other area of low gravity east of the mine but whether this area is underlain by a large body of salt is not yet established.

Jan 1, 1936

By C. F. Riisness, E. R. Parker

That grain size has a great effect on the mechanical properties of metals has been recognized for a long time. Bassett and Davis1 in 1919 did excellent work in determining the effect of grain size on the hardness of brass. About the same time Jeffries2 and Sykes3 ascertained the effect of grain size on the strength and ductility of several metals at temperatures ranging from 80°K. to their melting points. When creep was recognized as an important property of metals, those engaged in the study of this property tried to determine the effect of grain size4-9 on creep rates. Unfortunately, most of the investigations were conducted on only two grain sizes, often designated simply as "fine" and "coarse." It is well known that at high temperatures coarse-grained test bars creep less than fine-grained bars. The relation between grain size and size of test bar, however, has been frequently overlooked. In his early work, Jeffries2 showed that the number of grains in the cross section has a more important influence on the properties of the material than the actual grain size. More recently Hanson and Sandfordl0 and Pell-Walpole,ll in their measurements of the creep and tensile properties of tin, tested a wide range of grain sizes and correlated the grain size with the strength. Hanson9 later established the relation between the number of grains in the cross section and the creep rate. At high temperatures, generally a coarsegrained structure is considered superior in creep to a fine-grained structure, but it is evident that for a given bar size continuously increasing the grain size will

Jan 1, 1944

By Joseph C. Mead, James R. Cudworth

THE Birmingham district of Alabama has utilized the slag from its blast furnaces consistently since the earliest development of the slag industry. Today there are producers of slag cement who started business in 1900, and who have, under a progressive policy, expanded the number of their products to meet present demands. There are producers of slag aggregates and other crushed slag products who have been successful for periods of over thirty years. There are at the present two companies, Cheney Lime and Cement Co. and the Southern Cement Co., manufacturing puzzolan cement; two companies, Birmingham Slag Co. and Woodstock Slag Co., making slag aggregates and by-products; one company, Tennessee Coal, Iron and Railway Co., a subsidiary of the U. S. Steel Corporation, producing ground open-hearth basic slag for soil conditioning. Two companies, the Sloss Sheffield Steel and Iron Co. and the Woodstock Slag Co., make slag concrete in ready-mix plants and one company, the Superock Company, manufactures fine and coarse slag aggregates under a new granulation process. No Portland cement is made with slag as an ingredient, because dolomite is used so extensively as a blast-furnace flux that the magnesium content of the slag is excessive. Sources Of Slag In the Birmingham district there are 22 blast furnaces, of which the majority are in blast. The present production is 165,000 tons of pig iron monthly; the production in 1935 was 1,297,960 gross tons1. There are also two blast furnaces at Gadsden and one ferroalloy electric furnace at Anniston. From these two sources is obtained slag to approximately 1.1 tons per ton of pig iron.

Jan 1, 1937

By G. F. Tagg

Earth-resistivity measurements are often of service in obtaining information regarding geological formations, particularly when applied to structural problems. In such problems the masses of the various bodies are large, and have a corresponding effect on the average resistivity of the soil. Much work has been done using such measurements, but in general the method of interpretation employed is empirical. Since certain simple cases can be investigated mathematically, it appears to be quite sound to endeavor to apply the mathematical solutions to the practical results, in order to deduce from the latter such unknown quantities as depth. This paper deals with such a method of interpretation for the simple case of a single horizontal stratum. In the method described by Wennerl for measuring earth resistivity, four stake electrodes are driven into the earth in a straight line as shown in Fig. 1. A current I amperes is passed between the two outer stakes and the potential difference V volts between the two inner stakes is measured. Then if a is the electrode separation, the specific resistance of the soil, which is assumed to be homogeneous, is given by the formula P = 2?v/1 [1] v or if v/1 is called a resistance R ohms, p = 2?aR [2] If a is in inches, p will be in ohms per inch cube, or ohm-inches, and if a is in centimeters, p will be in ohms per centimeter cube or ohm-centimeters. As stated above, this formula is true only if the earth is homogeneous, and when this is not the case an application of one of these formulas

Jan 1, 1934

By D. M. Deason, R. M. Chhatre, G. Y. Onoda

INTRODUCTION The treatment of colloidal suspensions is a subject of increasing interest in mining and benefication (1). Colloidal suspensions are not readily operated upon by mechanical and physical methods useful with coarse suspensions, such as filtration, thickening, and flotation. This is because colloids are strongly affected by interfacial and interparticle forces that may be large compared with, and resistant to, external forces. The degree and type of interactions between colloids can be modified by small additions of reagents such as coagulants, flocculants, dispersants, and immiscible liquids. These alterations in turn change the properties of the suspension and provide possible opportunities for transforming suspensions to a more favorable condition for a given processing operation. Phosphate slimes are an example of a colloidal system of interest today. In the mining and beneficiation of phosphate rock in Florida, slimes are a waste product. The phosphate ore (called matrix in the industry) is slurrified hydraulically and pumped to a beneficiation plant, where the -150 mesh material is removed by cycloning from the coarser phosphate rock and silica. The resulting -150 mesh slurry, called phosphate slime, is pumped to large impoundments. The solid content of the slime entering the impoundment is around four weight percent, and over 80% of the solids is less than one micron in size. The immediate problems with phosphate slime relate to their disposal (2, 3). The disposal problem is associated with the very large volumes and the poor dewatering characteristics of the slimes. To have sufficient impoundment volume, large earthen dams are built around the mined areas. The volume above ground level approaches and

Jan 1, 1980

By Clarence P. Linville

It is recognized that, in all metallurgical operations, the greatest possible uniformity in all conditions is essential to the best results. It is the constant aim of metallurgists to secure this uniformity, and their success in this respect has been in many cases the cause of great advances in the metallurgical processes themselves. Of all such processes, the production of pig-iron in the modern blast-furnace is perhaps the most complex and the most difficult of control. Notwithstanding the great progress of recent years, there is still great difficulty in obtaining anything like uniform conditions and results in the manufacture of pig-iron. The reason is not far to seek. The ores vary in composition and physical properties, often carrying a varying amount of gangue material, unevenly distributed. The coke may vary in composition, cell-structure, moisture, hardness, and other properties. The blast, the weight of which far exceeds that of any other constituent, varies in its moisture-content and consequently in its chemical composition; and its temperature, by reason of the method of heating, is not uniform, but, besides varying from time to time with atmospheric and other outside conditions, has a maximum and minimum for every changing of stoves. Now, with regard to these variations, the modern demand for uniformity has been greatly aided. Chemical analysis has made it possible to select ores so that the composition of the charge can be kept fairly constant; coal may be obtained from a given field, and coked in the same kind of ovens under conditions which make the fuel practically uniform; the Gayley

Jan 1, 1911

By A. Hamilton Garner

The occurrence of oil seepages in Venezuela has been known since the early days of Spanish occupation. It was not until 1912, however, that any serious exploration work was undertaken. In that year, the Caribbean Petroleum Co., then a subsidiary of the General Asphalt Co., employed a large staff of geologists to make a systematic survey of large areas in eastern and western Venezuela, selecting the most desirable localities out of the immense area covered by the Valladares concession. This preliminary work was completed in the fall of 1913, and in February, 1914, the company completed its first commercial well at Mene Grande. Development work has progressed slowly, for various reasons, but petroleum in quantity has been encountered in nine widely separated localities. The Mene Grande field has been put on a producing basis and approximately 4,000,000 bbl. of oil is being shipped annually. Increasing quantities of oil are now being drawn from El Mene and La Rosa. In the light of these developments, the world&apos;s need for oil reserves, and the proximity of Venezuela to the United States, American capital is being attracted more and more to Venezuela. Although considerable careful geological work has been done in Venezuela by the various oil companies now operating, most of the data is buried in the company files, and the published literature has been extremely meager. The most valuable contribution to date has been a map and report by Jahn, which, as it was printed in Spanish, is not generally available to the American oil public. Venezuela, located in the northwestern part of South America on the Caribbean Sea, lies between l° and 12° north latitude. Its principal

Jan 1, 1925

By E. J. Schmitz

The mining of the Triassic coals of the Richmond basin has been carried on, upon a larger or smaller scale, for more than a hundred years. Notwithstanding the close proximity of the field to a large city and to tide-water, assuring both a good home-market and cheap transportation, and notwithstanding the good quality of the fuel and the great thickness of the principal bed developed and worked, operations in this field have been conducted with but limited success. The basin comprises about 189 square miles, being from 24 to 31½ miles in length by 5½ to 10 miles in width. Not much more than one-tenth of this area has been explored in a practical and efficient way, and not over 1200 acres have been worked near and along the outcrops or edges of the coal. The practical mistakes which have been committed undoubtedly in a number of the mine-operations of the past, do not alone explain the unsatisfactory success and progress of the industry of this field ; nor can it be ascribed to the lack of local enterprise. Other reasons have to be looked for; and, as a principal one, the irregularity and the faulted conditions of the coal deposits must be pointed out. As a second cause, the indifference of the State government, which leaves the development of the field entirely to private enterprise, instead of aiding it by systematical and practical geological investigations, deserves to be mentioned. Nothing has been done by the State since the excellent work done more than fifty years ago by Professor Rogers, who could not at that time enter into the details of such

Jan 1, 1895

By F. W. Osterwald, C. R. Dunrud

A continuously recording seismic network was constructed in 1962 by the U.S. Geological Survey to locate epicenters and record incidence of bumps (bounces, rock bursts) that occur in the bituminous coal mines of the Book Cliffs coal field near Sunny-side, Utah. The coal is mined because of its value as coking coal, although these bumps may be a hazard to life and property. Daily records of tremors caused by bumps for 1 3/4 years indicate that a seasonal pattern, as well as a daily pattern, exists for the number of bumps that occur in a given period. Maxima occur in May and June and November and December. Marked increases at 5-day to 9-day intervals are superimposed on these seasonal maxima. The largest bumps commonly occur during seasonal maxima when the rate of occurrence suddenly decreases and the amplitude of the individual bumps increases. Knowledge of this pattern may lead to prediction of general locations and periods of increased hazard from bumps. Experience to date has shown that prediction of precise times and locations of hazardous bumps is not possible, and may never be; primarily because even a small bump can be a hazard to life and property. Some bumps or bump sequences are actually composites, consisting or two or more discrete bumps a few tenths of a second to a few seconds apart. Violent and spontaneous releases of coal and rock from faces, ribs and roofs of mines (termed bumps or bounces by miners) are a common hazard to life and property in the coal mines located in the Book Cliffs near Sunnyside, Utah (Fig. 1). These bumps

Jan 1, 1965

By New kensington P. A, W. L. Fink, H. R. Freche

The investigation of aluminum alloy systems prior to 1923 was severely handicapped by the low purity of the best aluminum available. However, by that time, the electrolytic purification of aluminum had been developed by the Aluminum Company of America,(1)† and in May, 1923, there was initiated, under the direction of E. H. Dix, Jr.,(2) a program for the investigation of the aluminum-alloy systems using the purest electrolytically refined aluminum. Up to the present time 15 papers (3) have been published, most of which are on the binary aluminum systems. Work is now in progress on the ternary systems, and it seems probable that most of the future work will be on ternary systems. Therefore this survey of the binary aluminum systems investigatcd up to the present time (the sixteenth paper of the series) concludes the first phase of this program. Certain qualitative relations between corresponding portions of the various binary diagrams as well as between different parts of the same diagram were noted some time ago by R. S. Archer.(4) In the present paper these relations and others are considered quantitatively by the application of well-known thermodynamic equations or by newly discovered empirical relations. No attempt will be made here to present the history of the development of the thermodynamic equations defining equilibrium or their application to metallic systems, although a list of references is given at the end of this paper for those who are interested in this phase of the subject. Two thermodynamic equations, which will be employed extensively in this paper, are: loge x1 = - L/RT + C

Jan 1, 1934