Search Documents

By T. A. Rickard

Slovenliness is as reprehensible in words as in clothes. Much writing that we recognize as poor in style is merely sloppy. Just as some students postpone the necessary shave or forget to change their collars, so young engineers in writing drop their articles, definite and indefinite, or omit prepositions where they are required, possibly to compensate for these they use unnecessarily The work will begin [on] Saturday. The work will begin [on] Saturday. `Influenza seriously affected many mines [during] the last three months. Flotation in America [during] the last two years has made tremendous strides. Construction of the mill started [on] August 12, 1915, at which time 75% of the excavation was completed. The idea I wish to convey is [that] there are mineral deposits to which the present law applies badly. For this reason, if there was [for] no other, the ownership of the ore below and [of] the surface above should go together. When a unit of mapping is furnished, be the unit a claim or [a] group of claims, it is necessary .. . A fully stocked store was started in Park City and all employees [were] sold merchandise on a strictly cost basis. The word "merchandise" is left without government or agreement. I suggest: ". . . and merchandise] was sold to all the employees on a strictly cash basis.". The verb `be' is serving concurrently both as a principal and as an auxiliary in the following: At first the work was interesting and [was] liked by most of the men. The sulphide ore was more complex or [was] milled at an increased cost. The failure to repeat tie auxiliary verb in successive clauses is a common error, as in The filter is filled with liquid allowed to empty, and then ignited.

Jan 1, 1931

By M. F. COOLBAUGH

WHEN I was asked to speak on the subject of leaching, I did not realize that a complete summary of recent progress in leaching had been given by Stuart Croasdale. I shall try to give some other phases of the subject that were not touched by Mr. Croasdale. Not all metallurgists are in harmony as to their methods of treating metals. If they were it would probably mean lack of progress. They can be divided into two classes-the pyrometallurgists, using fire means, and the hydrometallurgists, or those using leaching methods. Conflict is always good for progress; we have it in politics, and in religion there are fundamentalists, and those who are not fundamentalists. As representing pyrometallurgy, may I hope not to be classed among the fundamentalists. The leaching of ores is not new. The leaching of ores for the recovery of metals, however, is quite new. The older leaching was simply to recover the salts. Agricola, back in 1555, I think it was, outlined a great many methods of leaching for the recovery of salts. They called them solid juices at that time. There was no real competition, however, between leaching meth-

Jan 1, 1926

Iron and steel lire subjects that will receive the attention clue them at the meeting in. St. Louis. Within the past 2 years the smelting of iron ore on a large scale has been started in the St. Louis area, and the blast furnaces are in full operation. Ore is being received. from the Lake Superior region, in large barges .brought clown the Mississippi River. Firebrick, for the lining of the furnaces, is made in the. St. Louis district to a greater extent than elsewhere in the country. At this meeting, there will probably be a discussion of the possibilities of the increase of manganese production in this country, and of improved methods of using it in steel manufacture.

Jan 10, 1917

By Ralph E. Wood

X-ray fluorescence analysis can be profitably applied in the mineral industry by improving evaluation and control analyses, while offering lower cost and greater speed than conventional methods. Chemical analyses are not only a major item of cost in exploration and mining, as well as in milling and chemical treatment, but often cause evaluation and control of processing steps to lag behind operations. In the fields of geology and mining, the X-ray technique can be employed without destroying samples and, if necessary, specimens can be analyzed and then used, unchanged, in other evaluation techniques. Results are quickly made available for decisions on progress of exploration or sorting of waste and ore.

Jan 6, 1959

By R. J. Greaves

High-resolution seismic reflection profiling can be used to evaluate detailed structural and stratigraphic features of coal prospects. Since most coal prospects are relatively shallow, less than 1000 m (3000 ft) deep, high sampling rates in space and time can be used effectively to improve vertical and lateral resolution of seismic data. The case study presented here shows how seismic data was used to evaluate the Wyodak coal at a prospective coal gasification site. The data were used to map the detailed structure and thickness of the coal and to search for lateral discontinuities, such as pinchouts and faults. An important find was a paleochannel cutting across the base of the coal seam, which was later confirmed by drilling.

Jan 1, 1986

By Michael A. Farrugia, Marcel Michaud

Remoteness of western Canadian coals has always been a barrier to the use of Canadian coals domestically. However, the world energy crunch, increased mining costs, stricter environmental controls, labor shortages, etc., are such that by 1980 a shortfall from traditional U.S. sources will prevail. Of necessity, Canada must then bring western coals east, requiring major new transportation initiatives. CN, CP Rail and Neptune Terminals are proceeding jointly with the design of a $30 million, fully automated, coal terminal at Thunder Bay. This element forms part of a $400 million integral transportation system to open new lines, improve trackage, acquire rolling stock and ships, for an initial capacity of 3 million tpy.

Jan 1, 1977

By Cyril Smith

A STUDY of the precipitation-hardening of copper steels1 led the authors to investigate malleable iron containing copper, for the low-carbon ferritic matrix in malleable iron should lend itself admirably to precipitation-hardening. It was soon found that in addition to rendering malleable iron susceptible to improvement by precipitation-hardening treatments, copper has another potentially useful effect as an accelerator of graphitization. Brief mention of these effects was given in a general paper by Lorig and one of the present authors2; the present paper gives further details on the graphitization and precipitation-hardening effects only. After the completion of this work a paper by L. Lykkin3 appeared, confirming the authors' conclusions regarding graphitization.

Jan 1, 1935

By A. M. Abouzeid, S. Chander, D. W. Fuerstenau

Today numerous ores contain valuable minerals in finely disseminated form; and although the recovery of these fine mineral particles is generally exceedingly difficult, diminishing raw material resources necessitates the recovery of such mineral values. In many systems, the efficiency of recovering fine particles is still extremely low and often fine particles must be discarded as slimes. However, in recent years, various advances have taken place in the recovery of mineral particles in the very fine size range. In this paper, the background and performance of a number of processes for fine particle processing and separation are reviewed and discussed, particularly from the point of view of how fine particle recovery might be improved.

Jan 1, 1979

By H. William Ahrenholz

The coal industry had another prosperous year in 1966. Since the turn of the decade, production has been climbing at an average rate of 6% per annum. Although the fast pace slackened somewhat, 1966 production showed a gain of almost 3 % over that of 1965. An impressive record can be drawn from the fact that output per man-day in 1966 was more than twice that of the early 1950's, and more than three times that of the early 1940's. And even though man-power requirements lessened, those men retained by the industry worked longer hours and benefited through higher hourly pay rates. However, cost to the customer increased a little. Such statements can only be made for a healthy industry -one that is constantly improving its efficiency. Coal currently provides more than 25% of the total U.S. energy output. About 50% of all U.S.- mined bituminous coal goes directly to the electric utility market. It should be noted that, now, well over one trillion kwh of electricity is generated annually. Dependence of the giant electric utility industry on coal is based on economy and an abundant, dependable supply of this fuel.

Jan 2, 1967

By F. S. Norcross

DEVELOPMENT of the manganese deposits of Cuba is a matter of importance not only to those involved in this industry on the Island but to the United States steel industry and to our Nation as a whole. For years our domestic resources of manganese have been wholly inadequate, but the recent Cuban development points the way toward solution of this strategic mineral problem.

Jan 1, 1939

By A. E. Lillstrom

IN the development of iron mines and production of iron ore from the Marquette range, drilling blast-holes is an important phase of the mining cycle. The ground drilled in ore production can be classified into two main categories, soft hematite and hard hematite or magnetite. Within these categories the material exhibits a wide range of penetrability by percussion drills. Development work encounters various types of rock. Slate and altered basic intrusives constitute the softer types commonly encountered. Harder materials are represented mainly by greywacke, quartzite, iron formation, and diorite. Prior to the first tungsten carbide trials in late 1947 and early 1948, hard-rock and ore drilling was done with steel jackbits starting at 21/4-in. diam. These were reconditioned by hot milling. Automatic or handcrank 31/2-in. drifters were employed, mounted on Jumbos, posts and arms, or tripods, depending upon the working place. With the exception of shaft sinking jobs where 55-lb sinker machines were and still are used with 1-in. quarter octagon steel, the other production and development mining utilized 11/4-in. round and Leyner-lugged steel. The following properties have been selected as typical examples wherein carbide bit applications have proved economical. The Mather mine "A" and "B" shafts and Cleveland-Cliffs Iron Co. mines are soft ore mines where insert bits are used in rock development only. The Greenwood mine, Inland Steel Co., Champion mine, North Range Mining Co., and Cliffs shaft mine, Cleveland-Cliffs Iron Co., are hard ore mines where all drilling is done with tungsten carbide bits. Mother Mine "A" Shaft In the Mather mine "A" shaft and other soft ore properties where only rock development work is done with the tungsten carbide bits, several types and makes of bits have been tried since early 1948. The greatest proportion of failures have been at the connection end, although the early trials with the 13 Series Carset 11/2-in. bit used in conjunction with 31/2 -in. automatic-feed drifters, showed an equal amount of shattered inserts. To combat this shattering, the 31/2 -in. drifters were replaced by 3-in. drifters, thus eliminating, for the most part, insert failures. However, the attachment end of the rod continued to be the main source of trouble. The greatest amount of failure was in the stud or at the upset section approximately 2 in. behind the drive shoulder of the rod. Heat treatment was changed several times as well as the composition of the alloy studs. Since this failed to correct the trouble, a decision was made to change to a heavier attachment section. Timken 11/2-in., type M, bits were then employed and showed an exceptional improvement. The rods are discarded when the thread contour shows sharpening or wear on the shoulder. It was also learned that the Timken insert did not show as rapid gage and cutting edge wear as did competitive makes, and footage per use increased by approximately 50 pct. Prior to the Timken trials the average life per bit at the Mather mine "A" shaft on 6-ft change chain-feed drifters was 500 ft, and the rod life at the connection end was 50 ft. The Timken bit with chrome-plated thread averaged 1200 ft, and rod life increased to as much as 500 ft. However, the life of the connection end was much better on shorter length drill rods or in places where machines with 34-in. change were used. The bit thread continued to be the point of ultimate failure with thread strippage, constituting the cause for discard of bits. In one of the new development headings, harder rock was encountered for approximately 800 ft, dropping the life per bit to a low of 90 ft with shank and thread life of rods dropping to approximately 125 ft average. The stripped bits were then welded to the rods, increasing the life per bit by 75 to 100 pct. The rod transportation for main level development was not a problem so intraset rods were tried. Intraset rods have tungsten carbide inserts set into the rods proper by the manufacturer and can be obtained with chisel or four point bits. This type of rod eliminates the need for any connection and the steel being a special alloy will show more feet drilled per rod. The first trial was made with eight rods, and final results averaged 350 ft per rod, six of the rods worked the life of the bit end, and two broke shanks at less than 50 ft. The preceding example showed a considerable improvement, so additional steel of the same type was purchased, but its use has been limited to main level drifting only, because of the handling problem involved in transportation of the complete rod to mine shops for resharpening. Further trials are being made on improving the life per detachable bit by chrome plating. To date, the chrome plating shows an improvement of approximately 100 pct. However, final results will not be known until the present long term trials have been completed. Mother Mine "B" Shaft In November 1947, tungsten carbide bits were first tried at the Mather mine "B" shaft. The use of 1%-in. Carset 13 Series bits, for drilling the 72-hole, 7-ft shaft round, decreased the drilling time from an average of 41/2 hr per round required with steel bits, to 2 hr with insert bits. The best drilling time for

Jan 1, 1952

By Charles H. Mitchell

British Columbia is enjoying a period of sustained high-level activity in all aspects and sectors of its mining industry. The total value of mineral production for 1962 was in excess of $229 million. This was the greatest total value attained for any year to date, exceeding the previous record year of 1956 by more than $40 million. It appears reasonable to expect that value of production for 1963, stimulated by increased production attained during the year, and by improved metal prices for some of the major products, will be substantially in excess of that recorded for 1962. Elsewhere in this issue appears a detailed report of prospecting and exploration activity in the Province. For the purposes of this review it is sufficient to state that the level of prospecting and exploration activity during the past several years has been greater than at any previous time and that there does not appear to be any slackening in activity or interest.

Jan 12, 1963

By R. P. Aikman, F. G. Miller, J. M. Podgursky

In response to the growing demand for low-sulfur coking coal for iron-making, the coal industry is continually striving to perfect methods for cleaning coal to acceptable ash and sulfur levels while maintaining maximum product yield. By present standards the industry has adequate processes for cleaning coarse coal, (i.e., +28 mesh) at almost any desired specific gravity. However, in the case of fine coal (i.e., -28 mesh) neither of the two existing processes-froth flotation and hydrocycloning-in its present state of development yields products that are comparable in ash and/or sulfur content to products normally obtained from coarse coal processes. The work outlined in this article is part of a larger study directed toward maximum exploitation of froth flotation for fine coal processing. The concepts and data presented are now serving as a basis for designing fine-coal circuits in which improved efficiency is obtained by optimum use of froth flotation with other fine-coal processing methods.

Jan 7, 1967

By S. D. Michaelson

Open pits and quarries are the major sources of all "hard rock" tonnage mined today. Normally, ore is fractured from the pit face by blasting and then truck-hauled to a primary crusher where pro- cessing begins; overburden (or waste) is generally truck-hauled from the pit to dump areas. Truck haulage of blasted ore and overburden accounts for some 25 to 50% of total mining costs in a typical open pit and commonly is the largest single cost factor. Obviously then, cost reduction efforts should properly focus on improving existing haulage systems and developing new breakthrough techniques for material transport. Continuous flow systems for large tonnages ordinarily will result in a lower cost than batch systems such as truck or rail haulage. Continuous flow with pipelines for liquids and slurries, or conveyors for medium to coarse dry materials (in the -8-in. range) are the economic answers for bulk materials handling over reasonable distances.

Jan 11, 1968

By J. J. Forbes

Probably the newest thing in mining safety, or safety for mines, is the apparent dissatisfaction on the part of the mineral industries, as represented by both management and labor, and the general public of the Nation, with the safety record of the mining industry. This is reflected by published comments and papers in the technical press;1-8 in labor periodicals, 10 11 in popular journals and periodicals,12 13 and in the daily press; also by discussions of the Safety Committees sponsored by the National Safety Council, 9, 14-15 the American Mining Congress, 1, 16 the American Institute of Mining and Metallurgical Engineers, 2, 4 the Mine Inspectors' Institute of America,6,8,17,18 the Coal Mining Institute of America, 5, 19, the American Standards Association, and others.20,21

Jan 1, 1949

By R. L. Minckler

PETROLEUM industry forecasts are constantly made and revised but are not in the nature of predictions. Particularly in the field of demand, many of the factors are far beyond control by the producing industry. Supply reacts on demand and demand reacts on supply. Competent economists in the oil business forecasted a year ago, on the basis of experience, that demand would now be at a much lower level than it is. This increased demand increased the price of crude oil and products, and in turn those increased prices have brought forth increased supply. A reduction in demand would lead to a reduction in supply. Shortages are now world-wide, and costs of secondary importance, so if there were extra supplies in California they would be moved into what are termed "unnatural markets." For example, Argentina is in the market today for California gasoline; that is an unnatural market because of the greater transportation distances from California to Argentina than from normal sources.

Jan 1, 1947

By T. Imaizumi

Covering the whole scope of the MMIJ activities, i.e. geology and exploration, mining, mineral processing, and metallurgy, the technical innovations and improvements since 1972 were reviewed. Special references were made to the MMIJ Research Committees which were subsidized by the Japan Mining Promotive Foundation, in connection with those activities.

Jan 1, 1976

By Edward W. Parker

(Toronto Meeting, July, 1907.) NOTE.-The material from which this paper has been prepared was collected for the U. S. Geological Survey Bulletin, Contributions to Economic Geology, 1906, and appears also, though in somewhat more extended form without illustrations, in that publication. ALTHOUGH the briquetting of coals and lignites has been carried on for many years in Europe, and has reached a particularly high state of development in France, Belgium, and Germany, it has made comparatively little progress in the United States. The causes for the backwardness of the United States in this regard are several, and first among them has been the abundant supply of cheap raw fuel with which the manufactured article has to compete. With our millions of acres of coal-productive territory, from which the product can in most cases be cheaply extracted, it has appeared in many districts more economical to waste the slack or culm, which con¬stitutes a considerable percentage -of the product, than to attempt to save it at the additional expense required for briquetting. It is for this reason that the view in all sections of the anthracite-region of Pennsylvania is marred by the unsightly culm-banks which encumber the ground, and that in some of the bituminous-districts one sees huge piles of unmarketable- slack allowed to burn up in order to get rid of them. When the coal is of a coking quality, or when the slack can be used for steaming-purposes, these losses are not sustained, but many thousands of tons of what might be converted into usable fuel have been wasted every year simply because of the increased expense involved in its preparation.

Sep 1, 1907

By Edmund J. Korber, Donald E. Raab, Frank A. Burns

During the early 1960s, the advent of self- advancing longwall roof supports triggered serious consideration by Bethlehem management to introduce the technique of longwall mining at one of our central Pennsylvania coal mines. Although longwall mining was initially justified as a means to cope with the severe roof conditions at our Mine 32 (Watson, B., 1971), the result of the endeavor has been a consistent and reliable level of coal production, first from Mine 32 and then later from Mine 33, over a period of fifteen years. Longwall production from the Cambria Division has been the mainstay of the low volatile coal required by Bethlehem Steel for steel production. Let us review the events that led to this accomplishment, as well as where we stand today.

Jan 1, 1981

By E. M. Wise

THOUGH known as the platinum-group metal- the sextuplet, platinum, palladium, iridium. rhodium, osmium, ruthenium, might well be called the American metals or perhaps Pan-American metals, as the ore containing them eras first discovered in South America, and in recent years the largest production has come from North America. The South American alluvial deposits, which also, contain gold, are in active production, as are the alluvial platinum deposits of Alaska, but the main production is from the copper-nickel ores of Sudbury, Ontario. The Russian deposits in the Urals were the source of most of the worlds platinum for about 100 years, but since 1934 have assumed second place. For a time considerable amounts of platinum came from several rather rich deposits in South Africa but these were exhausted quickly. However, a tremendous reserve of lower-grade ore exists there, which could be worked profitably if the price of platinum were considerably higher.

Jan 1, 1942