Search Documents

By R. F. Rolsten

The preparation of pure metals by the thermal decomposition of volatile halides was developed byde boer' and van Arkel.2 This has proved to be a useful technique for the refining of columbium,the mechanical and physical properties of which are seriously altered by such interstitial contaminants as oxygen, nitrogen, hydrogen, and carbon. The conventional deposition surface of a resis-tively heated metal filament was replaced, Fig. I, with an indirectly heated clear quartz surface. The impure columbium (feed) was contained in the annular space between the Vycor deposition bulb and the perforated molybdenum retaining cylinder. The head assembly was attached to the deposition bulb by fusing the Vycor at "A". This unit was then connected to a vacuum system composed of a three-turn glass coil to eliminate fracture due to vibration or expansion, a McLeod gage, a cold trap, a two-stage mercury diffusion pump, and a mechanical pump. The entire system was cold outgassed, and the 10 to 20 g of iodine in the auxiliary bulb (reservoir) was held in dry ice to prevent excessive loss of iodine. The columbium was hot outgassed at 800" to 825oC with the pressure maintained at l0-5 to 10-6 mm Hg for 48 hr and cooled under vacuum to 200° to 240oC. Iodine was sublimed from the reservoir and collected in the deposition bulb. The feed material temperature was adjusted to give the desired iodide vapor pressure and the finger temperature of 1000" C was independently attained and measured with a platinum-platinum 10 pct Rh thermocouple located in the center of the nichrome wire helical heating element, "F." The system was attended until temperature equilibrium was established, whence it operated without attention. This is a definite ad- vantage over the conventional "hot-wire" technique which required either constant attention or automatic control. In operation, the iodine vapor originally introduced into the vessel reacted with the crude metal to form a columbium iodide. This iodide vapor diffused to the hot deposition surface where it thermally decomposed, depositing columbium and releasing iodine. This liberated iodine then diffused back to the crude columbium where iodide was formed again. Thus, by repetition of this process, the iodine carried pure columbium from the crude material to the filament, where it deposited. The success of the "iodide" process in producing ductile metals depends on preventing the transfer of oxygen, nitrogen, hydrogen, and carbon from the feed material to the deposit. In many cases relatively minor quantities of these interstitial contaminants impair the ductility of metals. The material produced by the iodide process has such exceptional ductility that it is frequently and mistakenly assumed that iodide metal is always of very high purity. This assumption is not necessarily true since a number of metallic impurities can also be transferred. In the present investigation, the temperature of the feed material was adjusted to iodinate selectively and the deposition temperature adjusted to decompose the iodides selectively. By this technique, some metals present in the feed material were prevented from codepositing with the columbium. It is quite important to have the feed material symmetrically located around the deposition surface in order to obtain a uniform deposit at the maximum rate. For example, Runnalls and pidgeon3 observed that, when the base of a titanium filament was about 1 cm from the feed material, deposition was rapid on that section close to the feed, but that the rate decreased with distance from the feed so that a

Jan 1, 1960

By R. N. Thurston, E. A. Nesbitt, G. Y. Chin

A general relalionship between the amount of glide shear (due to slip) and the macroscopic shape change has been developed. Since the deformation can be large, finite strain analysis is employed. In this treatnzent, the shape change is expressed by a deformation gradient matrix, F - [axi/aXj1, where X and x refer to the initial and final positions of a particle. This matrix is readily evaluated in terms of the amounl of glide shear, a , and the direction cosines of the slip-plane normal and the slip direction for a single active slip system. In the case of deformation from slip on several systems, the product F(a) of the several deformation gradient matrices is first calculated. Then, by assuming that the final configuration is reached by a long series of small shears of magnitude a, occurring more or less alternately in the several slip sys- IN problems of crystal plasticity, it is often necessary to relate the amount of glide in the operating slip systems to the macroscopic strain components. This relationship is relatively simple when only small strains are considered. In this case the separate strain contributions from several slip systems are additive. Such a procedure is incorrect in the case of large plastic deformation. To the authors' knowledge, no general treatment of the latter problem has appeared in the literature. In specific instances, Mark, Polanyi, and schmid3 have derived the relationship between glide and axial elongation during tensile pulling of a single crystal when only one slip system is active. A similar relationship for duplex slip was worked out by v. Goler and Sachs.4 Taylor and Elam5 have also studied in detail problems of large plastic deformation. Due to uncertainties as to the slip systems at the time, terns, the final deformation gradient matrix can be obtained. Mathematically, the problem is reduced to finding the limit of F(dN as N — m while a — 0 in such a way that the Product Na = 0, a ftnite conslant designatzng the accunzulated amount of shear. It turns out that this limit is simply , where F, is the matrix whose elements are the coefficients of a in the F(a) matix. Application is made of the present treatment to a fcc crystal of Perlrzalloy compressed on the (110) plane and contrained to elongate zn the [112] directzon. In addition, it is shown that one rnay readily obtain from the general analyszs the well-known formulas relating elongation, amount of glide shear, and amount of lattice rotation for crystals deforming by single and double slip under tension. however, they were mainly concerned with proving that slip occurs on {111}(110) systems in fcc metals. The present general treatment arose out of recent investigations of magnetic anisotropy in cold-worked Fe-Ni alloys6 as well as some related problems in strength anisotropy of single crystals.' Detailed application of the general analysis will be provided in the case of a Permalloy single crystal compressed on the (110) plane and constrained to elongate only in the [112] direction. It will be seen that, as expected, the small strain approximation leads to significant errors after moderate straining. It will also be shown that the present general treatment yields the formulas of Mark et al. and of v. Goler and Sachs in those specific cases. GENERAL CONSIDERATIONS Consider a homogeneous deformation in which a material point initially at moves to both positions being referred to the same set of Cartesian axes. Such a deformation can be

Jan 1, 1967

By H. M. Davis, T. S. Jones

A methodfor accelerating the reduction of a metal oxide by carbon monoxide is to incorporate in the reduction system a nonreducible oxide which has a strong affinity for carbon dioxide and will remove it from the product gases. The effectiveness of this method was investigated by veduction experiments on specially prepared powder mixtures of SrO-ZnO ("active'.) and SrCO3-ZnO (reference). Measurements at 750o and 677°C showed that the rate of reduction of ZnO by CO was as much as an order of magnitude greater in the presence of SrO. Under the experimental conditions at least as much CO2 as generated by veduction was absorbed when SrO was present. Enlzancernent of the veduction rate by SvO resulted from modification of' gaseous djfitsion processes. THE specific question posed in this investigation was whether the reduction reaction CO + ZnO - Zn(g) + COa [1] could be accelerated by incorporating strontium oxide into the oxide charge undergoing reduction. Provided the strontium oxide was active enough, it could remove carbon dioxide from the product gases of ( 11 and form strontium carbonate, thus modifying Reaction [ 1] to CO + ZnO + SrO = Zn(g) + SrCO3 [ 2] This study of the comparative rates of Reactions [ I] and [2] can be considered as a particular case of a general scheme for increasing the rates of reduction of metal oxides by carbon monoxide. The limits of applicability of this scheme are indicated in the simple thermodynamic analysis presented in the appendix. This analysis primarily dictated the choice of the system, CO-ZnO-SrO, employed in this investigation. In addition, it was thought that a study of this scheme by use of the CO-ZnO-SrO reaction system would be of special interest in view of indications in the literature1-3 that the gaseous reduction of zinc oxide is prone to rate control by diffusion in the gas phase. The distinction should be pointed out between this and other efforts to increase the rates of reduction reactions through the use of addition agents. Additions of a wide range of chemicals have been tried with de- grees of apparent success varying from slightly negative to highly positive. The reasons for making additions have included the use of salts to produce effects akin to catalysis,4, 5 the alteration of the microstruc-tural details of the reduction process (including solid-state diffusion),6-8 and the conversion of an en-dothermic reaction into one that is exothermic or autogenous.9-12 The means used to attempt alteration of the enthalpy change has commonly been to incorporate lime into the charge, so that heat is generated by reaction with either of the reaction products, carbon dioxide or water. The use of lime in this way makes endeavors such as that of Edstrom and Wiberg similar to the present one. Furthermore, the basic principle behind the present work has previously been set forth.13 However, a detailed investigation of the type of reaction described in this work does not appear to have been conducted. EXPERIMENTAL PROCEDURE From both conceptual and physical standpoints, Reaction [2] is to be considered as the sum of two reactions:

Jan 1, 1968

By A. W. Bethune, L. M. Pidgeon

The equilibrium vapor pressure of zinc has been determined over the systems: ZnS(s) + Fe(s) = FeS(s) + Zn (vapor) and ZnS(s) + 2Cu(s) = Cu2S(s) + Zn (vapor) by reacting the components in an evacuated tube containing a thin copper fiber, and allowing equilibrium to be established with respect to the brass formed and the zinc in the vapor phase. The composition of the brass formed was determined and equilibrium vapor pressure values obtained from existing data. Between 850' and 1000°C, values for the first reaction ranged from 8 to 58 mm Hg; for the second reaction from 1.8 to 22 mm Hg. THE direct reduction of metallic sulphides may be indicated by an equation of the form MS + X = XS + M [1] where X is some suitable reducing agent. In the case where M is a metal of relatively high volatility, the use of vacuum will displace the equilibrium to the right at comparatively low temperatures in the face of the usually unfavorable thermochemistry. For this technique to be feasible, MS, X, and XS, must of course be nonvolatile compared to M. In this regard, zinc becomes an obvious metal both from the point of view of its volatility and the fact that most commercial ore deposits of this metal occur as the sulphide, and its direct reduction would avoid the expensive roasting process necessary prior to present day reduction methods. Two reducing agents are of interest, namely copper and iron, with the former having the added attraction of being relatively easily regenerated by oxidation in the copper converter. The possibility of these reactions has been considered before. Imbert1 patented a process whereby zinc sulphide was reduced by either copper or iron. The process as described took place at atmospheric pressure and, at the high temperatures required, the system was molten, resulting in the formation of a matte with the consequent reduction in the activities of the reactants. Peterson2 did further experimental work on these reactions and, although promising results were obtained on a small scale, attempts to increase the size of the furnace led to excessive "blue powder" formation. The early workers failed to realize the large reduction in temperature afforded by the use of vacuum and its desirable results. More recently, the direct reduction of zinc sulphide by iron has been the subject of a thermody-namic investigation by Kelley,3 and Gross and War-rington' have studied the kinetics of the reaction in the temperature range 900" to 1000°C, their experiments being conducted using vacuum and indicating that the reaction would proceed practically to completion in 1 to 3 hr, depending on the temperature. A qualitative examination of the system ZnS-Cu carried out at this University indicated that 98 pct of the theoretical zinc in the charge could be recovered in 1 hr at 1000°C when operating under reduced pressure. The purpose of this research program was to study the equilibrium of the two reactions. During the investigation, reference to the experimental work of Schenk5 was found but, due to lack of detail in the report, it was felt that it would be desirable to continue the equilibrium measurements. Selection of Method The measurement of vapor pressure of metals presents obvious problems resulting from the high temperatures which must be employed. In the present case, the production of the "reaction pressure" introduces a further difficulty since a chemical reaction must proceed before any metal vapor pressure is produced, resulting in depletion of the re-

Jan 1, 1954

By W. G. Bearden, G. C. Howard, J. W. Spurlock

An investigation of the factors af-fec.ting the inter-zonal flow of fluids in the casing-wellbore annrc1rt.s of an oil or gas ivell is presented Laborntory tests revealed that failure of the caring-cement bond allows communi-cation of fluid at pressure differentials near 1.000 psi. Perforating with a 11011011: carrier gun does not shatter or crack the cement sufficiently to allow communication through these cracks and does not seriously affect the casing-cement bond failure pressure. The pressure to cause communication at the casing-cement bond can he increared to 3,000 psi by. limiting pipe deformation during cementing and subsequent operations. Communication can be prevented, however. up to pressures sufficient to cause the cement to fail or the casing to col-lapse, by attaching to the casing a seal ring of deformable ruhber molded between two steel flanges. When installed, one flange is attached rigidlv to the casing to serve as back-up for the gasket While tile other flange is movable. To date, these gasket seal rings have been field-tested in 27 Wells. Althotrgh communication has been noted in two wells, inter-zonal flow has been prevented in other wells in the same area by installing more seal rings between the communicaring zones. INTRODUCTION The inter-zonal flow of fluids behind casing cemented in oil wells during normal production or stimulation operations is a major operating problem. If it cccurs during production operations. it can seriously limit the pressure to which a reservoir may be depleted without harmful invasion of unwanted fluids. If it occurs during stimulation operations, it may preclude the possibility of stimulating the desired zone. This communication can be caused by failure of the bond between the casing and cement, failure of the bond between the cement and formation, or failure of the cement itself. This paper presents the results of an investigation of factors affecting com-munication at the casing-cement bond and methods which aid in preventing it. LABORATORY INVESTIGATIONS The laboratory tests performed in this study were divided into three phases. The first phase consisted of tests to determine if perforating would shatter and crack the cement sheath so severely that communication would occur through the cement itself. The second phase consisted of tests to determine more precisely the cause for the casing-cement bond failure. The third phase consisted of tests to evaluate the effectiveness of various de-formable seals attached to the casing in preventing communication. EFFECT OF PERFORATING, The effect of perforating was invest~gated in tests performed with apparatus shown on Fig. 1. Cement was poured into the annulur space hetween 5%-in. casing and 8%-in. casing and allowed to cure for 72 hours. The apparatus was then perforated with a hollow carrier gun containing eight duPont 26-A shaped charges. Bull plugs were placed over the perforations in the 8 5/8-in. casing and hydraulic pressure was applied inside the 5 1/2i-in. casing. The pressure to cause fluid communication past the cement sheath was observed and termed the "bond failure pressure". Several different cement compositions were included in these tests, the results of which are shown in Table 1. In Tests 1 through 4 of Table 1, bond failure occurred at- the inter- .

Jan 1, 1966

By P. H. Metzger, D. W. Fuerstenau

The activation of sphalerite was found to occur at a much lower rate with Pb++ then with Cut++ or Ag+. To prevent activation with Pb++, the ratio [m in solution must approximate 103. An example is given illustrating how this condition is met in practice through the addition of zinc sulfate and soda ash. In selective lead-zinc flotation, the mill operator, especially the one who is concentrating a partially oxidized ore, often must add zinc sulfate and/or soda ash for effective depression of the sphalerite. In the present paper the authors show how this practice prevents the activation of sphalerite in the presence of Pb++. A number of years ago Gaudin (1) postulated that Zn++ might control the activation of sphalerite with Pb++ through competitive adsorption. However, recent experimentation has shown the activation of sphalerite with Ag+ and Cut++ to be a chemical reaction in which silver or copper ions replace zinc in the sphalerite lattice through the formation of a more insoluble sul-fide (2,3,4) Thus, if activation with Pb++ is similar to that with Ag+ or Cu t+, zinc salts should control the activation of sphalerite not through competitive adsorption but because the ratio of [zn++/Pb++] in solution regulates the extent of the chemical exchange between Zn++ and Pb++ in the solid phase. The objective of this investigation has been to study the kinetics and equilibrium conditions for the uptake of Pb++ by sphalerite and to investigate the prevention of lead activation with zinc salts. BASIC PRINCIPLES Sphalerite activation has been shown to be a replacement reaction wherein a less soluble compound is formed at the expense of the more soluble zinc sul-fide (2,3,4) For example, if sphalerite is placed in an aqueous silver nitrate solution, ZnS gives to the solution more S= than can exist together with Ag+, and hence the following reaction takes place: ZnS + 2 Ag+? Ag2 S + Zn ++; k = [zn ++]/[Ag ++]2 = 10 26 (1) Therefore, ZnS will dissolve in the presence of Ag+ and activation of sphalerite with Ag+ will proceed after monolayer coverage by solid state diffusion until equilibrium conditions are reached in the system (2, 4) Because of the large difference in the solubility of ZnS and Ag2S, zinc salts cannot affect the reaction unless a complexing agent, such as cyanide ions, is present to complex Ag+ more tightly than Zn++ . By complexing Ag+ and Zn++ in solution, the uptake of Ag+ by sphalerite can be regulated by controlling the ratio m. . Experimentally (2) it was found that the activation of sphalerite by Ag+ could be prevented through the addition of NaCN if this ratio reached a value of approximately 10 26. The mechanism of sphalerite activation with copper salts is given by the following reactions: ZnS + Cu ++ ? CuS + Zn + + ; (2) k = [Zn++]/[Cu++] = 10 11 ZnS + Cu + ? Cu2S+ Zn++; (3) Experimentally Mao (3) found that the activation of sphalerite with Cu++ or Cu + was prevented if the ratios expressed in Equations 2 and 3 were approximately l09 and l022, respectively, with cyanide ions as the deactivator. Although zinc salts do not affect the activation of sphalerite with silver or copper ions in the absence of a complexing agent, activation with lead ions theoretically can be controlled by the addition of zinc salts because of the relatively small differences between the solubility of ZnS and PbS (5). Equilibrium

Jan 1, 1961

By A. G. Worthing

Black: Bodies.-In the ordinary conception, a black object is an opaque object that reflects but little of the light that is incident on it. This means naturally that such an object is a good absorber of luminous radiation. The black body; which is so closely connected with high-temperature measurements, represents the limit in blackness of all black objects. It is a body that not only absorbs all visible radiations but also all other radiations in the infra-red and the ultra-violet regions of the spectrum which are incident on it. No substance is known that is completely black; platinum black, one of the nearest if not the nearest representative of the ideal, reflects 1 per cent. or so of ordinary visible radiation. The closest approach to the ideal is a small opening in the wall of a relatively large opaque cavity. Any radiation incident on this black body will be almost completely absorbed if the relative dimensions are properly chosen no matter what the material may be. The great difference between the blackness of such a cavity and of lampblack, for instance, will be apparent to one who makes the simple test. Non-black Bodies.-The field of non-black bodies covers all real bodies. Their characteristics are extremely varied. So far as absorption of radiation-is concerned, these bodies range practically from the almost completely black, platinum-black, and lampblack, which absorb all but a fractional part of 1 per cent. or so of the incident radiation, by an infinite variety of steps to freshly polished silver, which ordinarily absorbs only a few per cent. The exact percentage absorbed depends not only on the nature of the incident radiation, but also on the temperature of the body, the condition of its surface, the angle of incidence, the nature of the surrounding medium, and on certain other less important conditions. As consequences of these varied characteristics, we have not only the differences of color of ordinary objects, but also the changes of color that any one object undergoes on heating or when lighted front various directions. This complexity of the phenomena, in a way, is responsible for the meagerness of knowledge, regarding materials at elevated temperatures. Measurement of High Temperatures.-Excepting in cases where the thermocouple or the gas thermometer are applicable, in which case the temperatures obtained are true temperatures regardless of-the material" studied, high, temperatures are almost always, if not always, determined from measurements of radiation. In fact, determinations of temperature from this latter point of view are often so much more convenient than the thermocouple and especially the gas-thermometer determinations that, in the region where all of these types of measurements may be made, the radiation measurements are often preferred. This is true even though the temperatures usually thus directly determined are not the actual temperatures, a consequence of the sources of the radiation being non-black bodies; in other words, a consequence of being concerned with iron, or glass, or tungsten instead of small openings leading to relatively large-cavities uniformly heated. Coordination of Experimental Results.-In order that data on iron, glass, tungsten, or other non-black bodies obtained in one laboratory, may be, correlated with similar data obtained elsewhere, temperatures must be expressed on a common scale. The true temperature scale is the natural scale for this purpose it is ordinarily the scale to which all other temperatures can be most directly reduced. When the measurements depend on the radiation, a knowledge of emissive powers repre-

Jan 9, 1919

By N. Mungan, J. L. Thompson

Laboratory displacement tests were performed to study oil recovery elficiency by gravity drainage in fractured systems under miscible conditions. The porous media used were cylindrical Berea and Blue Jacket sandstone cores containing a number of well-defined, artificially formed, vertical and subvertical fractures. Butane and Soltrol 130 were the two miscible fluids used. The purpose of the study was to examine the influences of the displacement rate, fracture density, fracture orientation, fracture permeability, matrix permeability, crossflow, core length and connate water on the oil recovery. It was found that displacement rate, matrix permeability and the subvertical fractures affected oil recovery most. The critical flow rate, based on the matrix permeability, was found to be a significant factor in the process. For displacement rates below the critical flow rate, the oil recovery efficiency appeared to be unaffected by the density of the subvertical fractures. At the high displacement rates, the fracture density becomes important, with the recovery being the most efficient in the core having the greatest number of the subvertical fractures. The magnitude of the fracture permeability, the fracture orientation, the core length and the connate water have little effect on the oil recovery efficiency. INTRODUCTION Gravity drainage under miscible conditions from relatively thick reservoirs can be a very efficient recovery process, especially at low flow rates where the gravity forces are dominant and, consequently, the adverse viscous fingers associated with the unfavorable viscosity ratio are minimized or eliminated. Such a process might involve injection of an LPG or some solvent bank at the crest and then driving the bank with dry gas. For some favorable combination of reservoir temperature, pressure and oil composition, there may be no need to inject any solvent bank, since enrichment of the dry gas by the light ends of the crude creates an in-situ solvent bank. Slobod and Howlett2 have studied the effects of gravity segregation in vertical unconsolidated porous media under miscible conditions in the laboratory. The main variables in their study were the viscosity ratio, the density differences and the rate of flow. In this study, the objective was to find the influence of fractures on gravity drainage under miscible conditions. A greater number of related variables were also studied. LABORATORY STUDY CORE DESCRIPTION Displacement tests were performed mostly in cylindrical Berea sandstone cores. In a few cases in which a much lower matrix permeability was desired, Blue Jacket sandstone cores were used. The vertical fractures were formed by cutting the cores with a thin circular blade or by parting them along a bedding plane. The vertical fracture plane always contained the axis of the cylindrical core. The subvertical fractures, cut with a saw, were inclined 45' from the horizontal. The line of intersection between the planes of the vertical and subvertical fractures was parallel to the circular faces of the cores in all cases except one, as depicted by VF3HF-2 in Fig. 1. Fracture geometry of the other cores is also given in Fig. 1. Tables 1 and 2 give the physical properties of the solid and fractured cores, respectively. The suffixes and prefixes shown for each core have been used throughout the paper so that the reader may discern the fracture geometry from the core numbers.

Jan 1, 1970

By J. P. Boisseau, C. N. J. Wagner, E. N. Aqua

An analysis ulas made of powder-paltern peaks from cold-rolled polycrystalline copper and from copper powders, compacted into briquets (1 in. diameter) with pressures up to about 106 psi. Powder-pattern peaks from both contact faces were measured with a diffractometer and CuKa radiation. Laltice-parameter measurements indicate the presence of residual stresses in the bulk specimen of the order of a - -10 kg per sq mm after 93 pct reduction in thickness, and give some evidence for the occurrence of deformation stacking faults (probability a - 0.003) in both bulk and powder samples. Fourier analyses of the line profiles were carried out on the (111) - (222) and (200) - (400) Pairs of reflections. The particle sizes decrease rapidly with increasing deformation and reach asymptotic values of De (111) = 550A and D, (200) = 350A at about 25 pct reduction in thickness or 80,000 psi pressure for compaction. The anisotropy of the particle sizes indicates the presence of microtwins and stacking faults on (111) planes. The rms strains increase also with deformation and reach limiting values of 2 x 10-3 in the [100] direction and 1 x 10-3 in the [Ill] direction at a distance L = 100A normal to the reflecting planes. THE diffraction of X-rays in cold-worked, polycrystalline, fcc metals and alloys yields Debye-Scherrer patterns in which the individual (hkl) lines may show a broadening, a shift, and an asymmetric shape.' These effects can be explained by the fragmentation of the small, coherently diffracting domains, the presence of residual elastic strains in the lattice, and the formation of stacking faults. X-ray studies of stacking faults in fcc metals and alloys have been methodically performed during the last few years, but so far most of the investigators dealt with cold-worked powder specimens obtained by filing.2-8,10-19 In such specimens, the crystals are randomly oriented and the average elastic strains are assumed to be zero, so that the observed peak shifts are due to stacking faults only. The agreement between X-ray diffraction theory1,20 and experiment is generally good. On the contrary, cold-worked, polycrystalline bulk specimens (after wire drawing, rolling, plastic deformation by tension or compression, etc.) contain residual elastic strains, which may not average to zero in the surface of the specimen and show very strong preferred orientation of certain lattice planes (texture) parallel to the specimen surface. Nonzero elastic strains also produce peak shifts, the magnitudes of which depend upon the crystallographic orientation of the reflecting lattice planes in elastically anisotropic materials as well as on the type of plastic deformation and which have to be taken into account when measuring stacking-fault probabilities in deformed bulk specimens.21-23 The purpose of the present investigations was to perform a detailed X-ray analysis on a bulk specimen of a fcc metal deformed by rolling at room temperature and on powder of the same material deformed by compaction, and to compare these results with those previously obtained on cold-worked filings.18 Pure copper was chosen for this study since it is known to produce only a small quantity of stacking faults by filing at room temperature.3,16,17,19 The residual elastic strain in the surface of the bulk copper should be the predominant factor determining

Jan 1, 1965

By W. T. Cardwell

Physically absurd, triple-valued saturations appear in the straight-forward solution of the Buckley-Leverell equations for the displacement of oil by water or gas. From an engineering viewpoint, the triple value causen no difficulty. It is well known how it may be compensnted in order to obtain physically meaningful, numerical results. From a scientific viewpoint, the question still arises: What did the triple value mean? This paper explains how and why the triple value arose in non-capillary Buckley-Leverett theory. The discussion should serve as a background for the understanding and use of the modern method of characteristics in di.~pkzc(>ment theory. INTRODUCTION Displacement theory was introduced to petroleum technologists in 1 941 by Buckley and Leverett.' Their first equation, which they wrote down without derivation, was equivalent to the following: ?s/?t= - qr/F ?f/?r (1) where S = saturation of displacing fluid (a fraction) r = time q,. = total volumetric velocity of both the displacing phase and the phase being displaced (usually, but not necessarily, assumed to be a constant) F = porosity (a fraction) f - fraction of the total volumetric velocity that is the volumetric velocity of the displacing phase (assumed to he a function of S only x = distance. Buckley and Leverett called Eq. I "a material balance equation". Actually it is derived from both a continuity equation, or material balance equation, and Darcy's law. Buckley and Leverett jumped from their Eq. 1 immediately to their Eq. 2, which was the equivalent of the following: (?x/?t)x = qr/F df/ds = qr/F f'(s) (2) The jump from Eq. 1 to Eq. 2 involves apparently simple mathematics, but in that apparently simple mathematics lies a subtle point that is part of the key to the meaning of the triple value to be discussed here. Eq. 2 may be readily interpreted as saying that a point of constant saturation (on a saturation-vs-dis-tance curve) moves with a constant velocity that is proportional to the total volumetric rate, inversely proportional to the porosity, and is otherwise a function of the saturation itself. So that if one knows the derivativc with respect to saturation of the fractional flow function, f(S), for each saturation, one knows the velocity of each point of the moving saturation-vs-distance curve. The function f(S) can he determined experimentally and its derivative f'(S) can be calculated. It turns out that the experimentally derived f'(S) is not a monotonic function of S, but instead it has a definite maximum and declines away at both high and low saturations. This in turn means, in accordance with Eq. 2, that on a moving saturation-vs-distance curve, ccrtain intermediate saturations will travel faster than the saturations either higher or lower. The result is indicated in Fig. 1. In Fig. 1, the abscissas represent distances along a column of porous medium, which column is assumed to be uniform in cross-section perpendicular to the ab-scissal direction. The ordinates represent fractions of pore space occupied by the displacing phase, which may be either water or gas. It is assumed that the saturation is uniform over all planes perpendicular to the abscissal direction. The saturation is a function only of time and one space variable. Time variation of the saturation is represented by change in shape of a curve such as curve AGJ, which represents the initial saturation-vs-

By J. Szekely, V. Stanek

Heat and gas flow interactions in nonisothermal packed beds were examined in the paper. A study was made of the response of the system to a step or pulse change in the inlet gas temperature, with a fixed value of the overall pressure drop across the bed. Under these conditions the heat flow and fluid flow transients are coupled because the convective heat transfer rate is alfected by the mass flow rate of the gas which, in turn, for a fixed pressure drop will depend on the temperature profile in the system. The Problem was stated in terms of differential equations, which were integrated numerically. The parameters used in the computation were so chosen to reflect the operation of the stack region of blast furnaces and sinterbeds. The computed results showed that the pressure drop-flou1 relationships and the rate of progress of the temperature fronts (waves) were strongly interrelated and were also markedly affected by variations in particle size and in void fraction. MANY metallurgical processes involve the contact of solid particles with a gas stream in a packed bed arrangement under nonisothermal conditions. Examples are shaft furnaces, regenerators, pebble heaters, and the sinter process. Although the heat and mass transfer aspects of packed bed processing have been extensively studied, the associated flow phenomena and in particular the effects of nonisothermality on the flow, have received little attention to date. :In fact, most of the previous workers considered the flow rate of the carrier gas time invariant and independent of the heat or mass transfer processSzekely and carr2 have shown that the pressure drop-flow relationships in nonisothermal packed beds may be strongly affected by the temperature profile within the system. These authors have devised a method for relating the pressure drop to flow for a given temperature profile. thus providing an extension of the Ergun equation to steady nonisothermal systems. Finally, in a recent paper willmot3 examined the response of regenerators to externally imposed changes in the gas flow rate. Both these investigations were somewhat specialized since, in general, neither the temperature distribution nor the gas flow rate may be regarded as truly independent variables, thus the heat transfer and the fluid flow problems have to be solved simultaneously. The work reported here is divided into two parts: in Part 1 the general formulation is given and a detailed discussion is presented of fixed bed systems. Part is devoted to systems in which a gas and particulate solids are contacted in a counter flow arrangement. FORMULATION Consider a nonisothermal fixed packed bed, extending from through which a gas is flowing. The problem is to develop a relationship between pressure drop and gas flow (with the gas flow being the dependent variable) and to evaluate the rate at which a change in the gas temperature, imposed at the inlet, travels through the system. Let us consider an infinitesimal section of the bed and establish differential heat, mass, and mechanical energy balances over this region. In addition, relationships are needed describing the temperature dependence of gas density (equation of state) and the temperature dependence of viscosity. These may be written as: where c, and are constants. It is noted that in this formulation we neglected any temperature gradients within the solid particles, thus assuming these to be either sufficiently small or of sufficiently high thermal conductivity to meet this condition. The justification and consequences of this assumption will be mentioned in the discussion.

Jan 1, 1970

By C. C. Mattax, J. E. Bobek, M. O. Denekas

ABSTRACT investigations in recent years have shown that rock wettability can exert a profound influence on the displacement of oil by water from oil producing reservoirs. Core analyses frequently show oil recoveries from preferentially water-wet rock to be significantly greater than those from preferentially oil-wet rock. Thus, an accurate prediction of water-drive or waterflood oil recovery is dependent on the evaluation of reservoir rock wettability. Laboratory and field studies have been undertaken to examine and develop methods which may be used to measure rock wettahililiy, to investigate factors which may alter the wettability of reservoir rock, and to determine the wettability of specific reservoirs. It has been found that measurement of the rate and volume of spontaneous imbibition of the wet-ting phase by a rock is a reliable and reproducible test for semi-quantitarive determination of preferential rock wettability. Laboratory tests have shown that the wettability of reservoir rock may depend on both the crude oil composition and the rock type. Field and laboratory tests have indicated that coring flulids and core handling techniques can cause significant changes in the wettability of rock surfaces. However, a few fluids, brine in particular, appear not to affect core wettability and may be used when coring to determine reservoir wettability. Core handling and packing procedures have been developed which preserve core wettability during storage and laboratory testing. The wetfability characteristics of six reservoirs have been evaluated by wettabilify tests performed in the field on fresh cores cut with brine or special water-base muds. The tests indicated that all six reservoirs are water wet; however, the de-gree differed from one reservoir to another. INTRODUCTION Although surface properties of reservoir rock and interfacial characteristics of rock, crude oil, and water systems have been discussed for many years, the full significance of these properties to the production of oil is still in the process of evaluation. It is known, however, that one surface characteristic—preferential wettability of the reservoir rock—-is of paramount importance when the reservoir is being produced by water-flood or water-drive mechanisms. The importance of rock wettability has been pointed out by several authors'.',%* who have found that pref- erentially water-wet cores flood more efficiently than oil-wet cores; that is, more oil is recovered from water-wet cores in the early flooding stages than from oil-wet cores. Other authors'," indicate that waterflood oil recovery from cores of intermediate wettability may be greater than that from either strongly water-wet or strongly oil-wet cores. These recent investigations emphasize that the true wettability of a reservoir must be known before the performance of waterflood or water-drive reservoirs can be accurately evaluated. When reservoir wettability is to be determined by core analysis, precautions must be taken to maintain the original wettability which can be altered readily during coring5 nd testing.' In the coring operation the core may be partially or completely penetrated by the drilling fluid which, if it contains surface active materials, may drastically change the wettability of the core. Also, improper core handling during stcrage and testing may change its wettability because of evaporation of fluids or exposure to oxygen or surface active contaminants. One purpose of this paper is to discuss methods for obtaining, preserving, and testing cores without altering their original wettability. In addition, the results of wettability tests on fresh and preserved cores from six reservoirs are presented where special precautions were taken to obtain samples without altering their wettability during the coring operation.

By S. Weinig, J. Winter

The grain boundary adsorption of solutes as a function of bulk concentration and solution temperature was studied using internal-frictimz techniques. From the variation of the cor-responding energy of activation for the Phenomenon, the inter-actior2 energy between a solute atom and a high-angle boundary was calculated. Interaction energies in the range of 0.3 ev were obtained, and were used to obtain the actual concentration of solute at the grain boundary. In corroboralory creel, studies the direct grain boundary contribution to the total creep strain was measured. It was found that the interface creep varied with the type and magnitude of the solute adsorbed. Subscribing to the theory of their being energetically favorable sites at the grain boundary for solutes of both Positive and negative size deviations, ternaries were investigated in Which solutes of both types were present. A marked increase in the resistance to grain boundary creep was manifested. THE major difficulty which has been encountered in investigations of the grain boundary segregation of solutes has been the lack of a sufficiently sensitive method of measuring the amount of adsorbed solute at the boundary. For the general case of a high-angle boundary, no direct method of measuring the adsorption at the boundary has been found to date. Internal friction has been used in several studies of grain boundary adsorption1-3 and although it is somewhat indirect, it was demonstrated to have the necessary sensitivity. In this investigation the authors have used internal-friction techniques in conjunction with a study of the grain boundary contribution to the total creep strain. As both parts of the investigation were performed on the same specimens it was possible to combine a highly sensitive technique with a somewhat more direct method in order to obtain information about the adsorption phenomenon. From internal-friction studies the rate of increase of the activation energy was observed to be a function of the difference in size between the solute and solvent atoms. It was proposed that if Gibbs' adsorption isotherm is considered, i.e., where r is the excess solute at the boundary, c is the bulk concentration, and ay/ac is the change in grain boundary energy with bulk concentration, then AH b/ac must vary in the same way as ay/ac and therefore In this way a relative measure of the grain boundary adsorption of solutes is directly obtainable from in-ternal-friction studies. If the previous work in the field of grain boundary adsorption of solutes is examined, certain apparent information is desirable if the phenomenon is to be understood. The most important questions that must be asked are as follows: 1) Is the adsorption of solutes at the grain boundary an equilibrium process? 2) Can the Mott model of the grain boundary be used as a basis of setting up an elastic interaction between the grain boundary and solute atoms? 3) Is it possible to obtain an exact measure of the excess solute at the grain boundary as a function of temperature and bulk concentration rather than merely a relative measure of the adsorption 4) Are the conclusions obtained from an indirect method such as internal-friction studies meaningful in considering gross grain boundary effects such as creep? EXPERIMENTAL PROCEDURE The material used in this investigation was Bureau of Mines "superpurity" titanium (79 Bhn—1500 kg

Jan 1, 1960

By R. A. Burton, J. T. Hansford, D. A. T. Donohue

Substantial evidence indicates that many petroleum producing horizons contain naturally occurring, ordered fracture systems and that within a particular geologic zone, vertical fractures induced in wellbores often will be directed along a particular compass direction. Both conditions will seriously alter the fluid displacement behavior within reservoirs. In this study the effect of induced fracture orientation and length on sweep efficiency is determined for a five-spot pattern. In general, it is assumed that all wells are fractured and directed along the same compass direction. Using the electrical analog to steady state, two-dimensional fluid flow in porous media, boundary conditions are obtained from which flood fronts are tracked numerically. The numerical computations require a particle tracking routine for approximating flood front histories. It is shown that recovery is sensitive to the length and orientation of fractures for the pattern studied. with the proper design of fracture-pattern systems, recovery can be enhanced considerably. INTRODUCTION Hydraulic fracturing introduced in 1949l gave the industry a rather inexpensive means of increasing the fluid injection or production capacity of wells. It has been used with particular success to increase the production rate of wells completed in tight formations, such as in western pennsylvania2 where producers have fractured in depleted or near-depleted fields and observed economic responses. Once the natural energy declines in such a reservoir where all wells have been fractured, waterflooding is generally suggested as means of further increasing recovery. Of the dual objective sought in waterflooding — high injectivity and high breakthrough sweep efficiency — the former condition can be obtained if all wells in the flood pattern are fractured; the latter condition should depend on the nature of the fracture system. Considerable theoretical work has been published on the nature of fractures induced in boreholes.3-5 Although discussion persists concerning the possibility of forming a horizontal fracture at a given point within the wellbore, it is generally conceded that only vertical fractures will develop below a given depth, i.e., where the fracturing Pressure is less than the overburden load. Given the fact that fractures will be vertical in most cases of interest, it is also important to know whether there is order to fracture orientations within a given geological region. Kehle has suggested that in tectonically relaxed areas of uncomplicated geology, the stresses are fairly uniform and all fractures in the region should be parallel.5 Dunlap arrived at a similar conclusion in a theoretical investigation of localized stress conditions surrounding the borehole.6 He concluded that most vertical fractures are propagated in a preferred azimuthal direction. Fraser and Pettitt, in extending these theoretical suggestions to a specific field case, used an impression packer to record both a vertical fracture and the orientation of this fracture in the wellbore of a well in the Howard Glasscock field, Tex.7 Use of this information enhanced the waterflood recovery of the field. Anderson and Stahl also used impression packers on three fractured wells in the Allegheny field. N. Y.. and found that the fractures were oriented more or less along the same compass direction.8 Orientation of the fractures in this manner depends on the stress condition within the formation during fracturing. Elkins and Skov have demonstrated that a natural, oriented, vertical fracture system exists within the Spraberry field? Heck suggests

Jan 1, 1969

By M. Kaufman, A. E. Palty

The phase structure and aging characteristics of two nickel-base alloys, Inconel 718 and 702, were investigated. Wrought and cast Inconel 718 showed ArisCb as the major hardening phase, as well as ture was positively identified. Inconel 702 had Ni3Al as the major hardening phase, as well as Cr7C3-of the phase amounts with temperature was determined. 1 HE value of phase structure and aging rate information in the utilization of alloys has been well established. As part of a continuing program, the results obtained on two nickel-base alloys, hconel 718 and Inconel 702, are presented here. Inconel 718 is a relatively new alloy considered for application in both sheet and cast form. Its novelty lies in the use of high columbium tantalum levels in a Ni-Cr-Fe base. No previous work on this type of alloy has been reported in the literature. Inconel 702 is being used now as an oxidation-resistant sheet alloy. Occasional fabrication problems spurred work on its basic structural behavior. The composition of 702 is essentially nichrome plus aluminum and titanium for strengthening and added oxidation resistance. This puts it in the basic class of other nickel-base alloys which have already been studied. The two alloys will be treated separately. INCONEL 718 Phase Study Methods. The phases present after the various conditions investigated were determined by X-ray diffraction analysis of two different elec-trolytically extracted residues and microscopic examination. The extraction methods, using 10 pct HC1 in alcohol and 10 pct H3PO, in water and the X-ray technique have been described previously.' The effect of temperature on the phase behavior was studied on sheet material using the following heat treatments: 2250°F, 2 hr, ice brine quench 1300 100 hr, water quench 2250°F, 2 hr, ice brine quench 1400°, 100 hr, water quench 2250°F, 2 hr, ice brine quench 1500°F, 100 hr, water quench 2250o 2 hr, ice brine quench 1700°F, 48 hr, water quench 2250°F, 2 hr, ice brine quench 1850°, 24 hr, water quench 2250°, 2 hr, ice brine quench 2000°F, 6 hr, water quench The high solution temperature was an attempt to dissolve as many phases as possible without causing melting. Aging exposures were made longer than normal heat treating times in order to approach equilibrium conditions more closely. Cast material was examined only in the as-cast condition and with the normal heat treatment (1700°F, 1 hr, air cool 1325oF, 16 hr,air cool). Materials. The full phase study was performed on sheet specimens approximately 1/2 in. by 2 in. by 1/16 in. The cast pieces were cut from the gating system of a vacuum-cast test piece. An all weld-metal specimen was made by running many weld beads on the sheet using filler made from the sheared edges of the sheet. All external contamination was removed by belt-sanding followed by an electro-polishing treatment. The typical composition of wrought Inco 718 is as follows: The alloy is air-melted. Cast hco 718 may have higher molybdenum. Due to the expectation of finding a Ni-Cb phase (Ni, Cb) for which no X-ray diffraction pattern was available in the ASTM Index, a special 5 Ib heat to the stoichiometric composition of this intermetallic

Jan 1, 1962

P. L. Pratt (University of Birmingham, Birmingham, England)—The author has measured the hardening effect of isolated edge and screw dislocation boundaries in a remarkably elegant manner, and he proposes that the detailed structure of the boundary determines its effectiveness as a barrier to slip although "there are still unknown details of the distribution which may be extremely important." On p. 678 the author states "that for a good crystal (one having a yield of about 30 psi) a change in annealing temperature from 300" to 400 °C resulted in a negligible shift in the level of the stress-strain curve." Is this in agreement with the results of the earlier paper by Li, Washburn, and Parker8 in which such a change of temperature produced notable hardening in crystals with a yield of about 30 psi? Or were these earlier crystals, of the same nominal purity, less perfect than those used in this work? The experiment illustrated in Fig. 15, p. 681, shows that the boundary has sharpened after annealing at 400 °C, the temperature at which the hardening effect first becomes apparent. Did the author verify that no sharpening of the boundary occurred at, say, 300 °C where no hardening was found? This would seem to be an important check on the proposed mechanism, especially since zinc of this purity should polygonize at temperatures well below 400 °C within the annealing times used here. There seem to be at least two alternative explanations which could fit these facts: 1—The boundary may sharpen at 300 °C or even lower temperatures but be unable to contribute greatly to the hardening until jogged by thermal vacancies and other impurity atoms after 400 °C anneal. This mechan- ism, discussed in the earlier paper,' is believed to account for the thermal hardening observed by Blank'" in NaCl, as stated elsewhere: and by results from recent experiments which tend to confirm this view. 2—The dislocations in the diffuse boundary may be locked by impurity atoms at 300 °C and thus only sharpen the boundary at 400 °C with the aid of thermal vacancies. In this case it would be difficult to distinguish between the two sources of hardening (sharpening or jogging), using metal of this purity. Jack Washburn (author's reply)—The author wishes to thank Dr. Pratt for his discussion. In connection with his first comment, it should be pointed out that the temperature of testing in the present series of experiments was —196°C, whereas, in the earlier experiments he referred to,' it was 20°C. Therefore, the yield values should not be directly compared. It is likely that the crystals used in the present work were initially more perfect macroscopically than the large shear specimens used previously. The small size of the test section in the kink specimens made it possible to select regions of the large crystals, from which they were acid-cut, that were free of observable small angle boundaries. The sharpening of a microscopically diffuse boundary such as that in Fig. 15 begins in zinc of this purity well below 300°C. However, it is probably not justified to conclude that because a boundary looks sharp under the microscope it has attained the ideal structure. The author agrees with Dr. Pratt that jogging of dislocation lines is one of the structural features of a small angle boundary that should be important in determining its strengthening effect. More detailed information concerning the changes in boundary structure as a

Jan 1, 1956

By M. P. Tixier, F. Segesman

Explanations bused on theory and laboratory tests tire offered for certain unusual features of SP logs which may befog their interpretation, namely the "sawtooth" SP and the reduction or increase of SP with time. The sawtooth SP is frequently seen in SP recordings of thick, very permeable watcr. sands of the Louisiana Gulf Coast. Using SP data from a resistor network analog, this anomaly is explained on the basis of a thin shale streak within the sand. under which the invading filtrate accumulates by gravity segregcitiorr. The electromotive force then appearing across the shale streak gives rise to the anomalous SP. Reduction of the SP on successive logging runs Ira often been observed in very permeable sands when as indicated by the resistivity curves, the invasion depth has been reduced to practically zero. Laboratory results verify that this phenomenon may be due, to the presence of air electromotive force, across the mod rake when the fluids on either side differ in activity. Also, there is, in some cases; an increase of SP deflection on successive logging runs, because the emf initially present across the mud cake disappears as the somewhat saline water just behind the mud cake is progressively flushed out by the invading filtrate.. Field example and laboratory data are presented. I N T R ODUCT1ON Some unusual features are frequently observed on certain SP logs which make interpretation difficult. The purpose of this paper is to offer explanations of several cases of interest. All of these arc related to the conditions of invasion. The cases to be discussed are as follows. 1. The sawtooth SP anomaly which is frequently seen within the thick, highly permeable saltwater sands of the Louisiuana Gulf Coast 1. Reduction of the SP deflection from the usual sand line in very permeable sections when the depth of invasion is practically nil. As will be explained, such a reduction is attributable to a membrane electromotive force across the mud cake. 3. An increase of the SP with time just after the iormation is drilled as a result of progressive flushing of the invaded zone. FUNDAMENTALS OF SP PHENOMENA An explanation of SP phenomena must begin with the following basic ideas. 1. The SP log derives its character from ohmic potential differences in the hole produced by currents flowing through the mud.' These currents are driven by electromotive forces which are primarily electrochemical in origin. Other possible types of SP-producing electromotive forces may be disregarded for the purposes of this paper. 2. The electrochemical emf's associated with permeable formations are now understood to consist of liquid-junction emf's and membrane emf's.',' As schematically shown by thc battery symbols in Fig. 1, the liquid-junction emf, E,,,, exists at the contact between waters of different chemical activities, a,,,, (mud filtrate) and tr,,. (formation water); the shale membrane emf, lS.sn. exists across the adjacent shales whcn they separate waters of different activities. The emf's just cited are additivc in producing SP currents (arrowed circles of Fig. I). Thus, neglecting for the moment any possible membrane emf across thc mud cake, the total electrochemical emf, E,, will be given by their sum, where K,., -! K,q,, = 12 + 59, or 71 at 75 °F. In the log interpretations the SP of a thick sand (i.e.. the static SP) is generally related to the activities of the filtrate and formation water through Eq. 1. by setting the static SP equal to - E,.

By Robert L. Dean, Michael Hoch, Samuel M. Wolosin, Chung K. Hwu

The general shape of the 1450°C isotherm of the Ti-TiO-ZrO2-Zr region was evaluated from the surrounding binary phase diagrams and from thermo-dynamic data on the metal-oxygen binaries. The phase boundaries were accurately determined using X-ray and metallographic techniques. At 1450°C the system shows a large bcc ß field, which extends from the two metal-oxygen binary systems as a Gaussian error function, and is stable up to 30 at. pct 0 when Ti and Zr are present in equal amounts. At higher O Concentrations, the ß field is in equilibrium with t-ZrO . The following four regions, with three solid phases, are present: two a ß t-ZrO,, a TW t-ZrO,, and TiO t-ZrO2 c-ZrO2. On cooling the ß phase transforms into the a phase, going through the w transition phase. The isotherm at 1500°C for the region TiO-TiO,-ZrO, was obtained by using X-ray diffraction. At 1500°C a large c-ZrOz region is present as well as a large two-phase field, Ti0 c-ZrO,. The following regions, with three solid phases in equilibrium, were found These regions are relatively small. The solidus and liquidus relationships were determined by observing samples suspended in a tungsten crucible by means of a fine tungsten wire and heated in vacuum. Eleven univariant points were found. C-ZrO, decomposes through a peritectic reaction into liquid t-ZrO2. The activities of Ti and TiO in the TiO t-ZrOz and in the two a ß t-ZrO regions were measured using the Knudsen effusion method. In the a TiO t-ZrO, region the activities of Ti and Ti are the same, as in the a — Ti TiO binary. In the two a t-ZrO, regions, the Ti activity is high and the Ti0 activity very low, although all phases present contain at least 30 at. pct 0. This indicates a short-range order in the solid phases, Zr atoms being preferentially surrounded by 0. 1 HE system Ti-Zr-0 is of interest because of the wide ranges of solid solubility exhibited by the boundary systems; as titanium and zirconium both belong to the same group of the periodic table, large single-phase regions should occur within the system, with a great variation of properties (as the composition changes within the single-phase region). Furthermore, the possibility of modifying ZrO, to make it a more usable refractory by the addition of other metals makes this system also of interest. Because of the high affinity of titanium and zirconium for oxygen, the oxygen partial pressure is very low at all compositions; thus, there exists a ternary metal-metal-oxygen system in which the oxygen pressure is not an important variable, so long as it is low enough. When a sample is heated in vacuum to a temperature high enough for vaporization to occur, the vapor phase will consist of metal and metal-oxide gas, the oxygen concentration being very low. The phase relationships in the surrounding binary systems have already been reported in the literature; therefore, the study of the ternary diagram

Jan 1, 1962

By R. W. Fountain, W. D. Forgeng

A new constitutional diagram is presented for the cobalt-rich end of the cobalt-titaniurn system. The modifications result from the presence of a new, intermediate, fcc phase, ?, the existence and homogeneity limits of which were established by metallo-graphic and X-ray studies of alloys containing from about 3 to 30 pct Ti. The precipitation of the ? phase from supersaturated solid solution was studied by hardness and electrical resistivity measzsrements, and two distinct stages in the process were observed. COBALT forms the base for a number of precipitation -hardenable alloy systems which may be divided into two distinct categories of practical interest, a) those hardened by intermetallic compounds and b) those hardened by carbide formation. The precipitation of intermetallic compounds from solid solution in cobalt-rich alloys has, however, received very little attention. Although the phase diagrams for some binary systems capable of precipitation have been determined,' there is an almost complete lack of data on the property changes associated with the precipitation, and even less information on the kinetics of the reactions or morphology of the products. More information is available on the precipitation of carbides because of the practical significance in superalloys. A survey of cobalt binary phase diagrams suggested that the cobalt-titanium alloys might provide interesting and useful precipitation-hardenable alloys. The equilibrium diagram as proposed by Wallbaum2 is shown in Fig. 1. Köster and wagner3 have indicated that the maximum solubility of titanium in cobalt is about 10 pct at the eutectic temperature (1135oC), and this decreases to about 7.2 pct at room temperature. The temperature of the allotropic transformation in cobalt is lowered by the addition of titanium, about 5 pct being sufficient to retain the high-temperature fcc modification to room temperature. Wallbaum and Witte 4,5 have indicated that the precipitating phase in alloys containing up to about 29 pct Ti is Co2Ti, a hexagonal Laves phase of the MgNi, type. With slightly higher titanium contents, they also report a cubic modification of Co2Ti of the MgCu2-type Laves phase. Duwez and Taylor6 confirmed the existence of the hexagonal (MgNi2) modification but not the cubic (MgCuz) modification of Co2Ti and suggested that existence of the cubic form may have resulted from impurities in Wallbaum's alloys. In their work on Laves-type phases, Elliott and Rostoker 7 reported the cubic modification of Co,Ti, but did not confirm the existence of the hexagonal modification. However, Dwight8 in a discussion of the work of Eliott and Rostoker again showed the existence of both modifications of Co2Ti, a result which was confirmed at that time by Elliott and Rostoker. As a result of a study on the iron-cobalt-titanium system, Köster and Gellers suggested the existence of a Co3Ti phase isomorphous with Fe3Ti. Witte and Wallbaum,' however, established the fact that no compound, Fe3Ti, exists in the iron-titanium system, and in a later publication, wallbaum2 stated that Kitster and Geller's reasoning was not valid, and no compound, Co3Ti, exists. This conclusion was later acknowledged by Köster.10 Preliminary experiments by the present authors to determine the precipitation-hardening characteristics of the cobalt-rich, cobalt-titanium alloys re-

Jan 1, 1960

By T. F. Bower, M. C. Flemings, H. D. Brody

A series of experiments are reported which show thai reasonable assumptions for analysis of solute redistribution in solidification of castings and ingols illclr(de: negligible undercooling before nuclcation of solid phases, negligible increase of solute in advance of the tips of growing dendrites, complete diffusion within the Liquid oer distances the order, of dentrite arm spacings, platelike dentrite t/o?$holog?.. Qzmli/ali,e and periment is obtained JOY Al-Cu alloys front measurements of amount of nonequilibrium second phase, minimum solute content at the centers dentrites arms (after solidification), and 3) change in minimum solute content in dentrite arms during solidification. In a previous paper' analyses were given describing solute redistribution in dendritic solidification. The analyses were undertaken primarily to permit prediction of "severity of microsegregation" in a casting or ingot after solidification and cooling to room temperature, but can also be used to predict "local fraction solid' as a function of temperature in the solidifying alloy. Numerical results were given for Al-Cu alloys. The aims of this paper are to examine the validity of some of the assumptions of that analysis, and to compare predictions of the theory with experiments. All experiments reported are on Al-Cu alloys, the bulk on Al-4.5 pct Cu alloy. EXPERIMENTS Experiments conducted were on small ingots, 41/2 in. in diam by about 10 in. high. solidified in a controlled thermal environment (i.e., in a resistance-heated, re-circulating air furnace, whose temperature could be controlled to 1°C). In one series of experiments, the ingots were solidified very slowly (solidification time was varied from 8 to 1000 hr) and at constant rate of heat extraction. In a second series of experiments the ingots were solidified ( 'unidirectionally". Fig. 1 is a sketch of the method of making the two different types of ingots. The unidirectionally solidified ingots were fully columnar, and the slowly solidified ingots had equiaxed structures, Fig. 2. In making the slowly solidified ingots, the mold employed was carbon steel, coated with inert refractory. Typically the mold and its environment were heated to 700°C. The molten alloy was then poured into the mold and the temperature of the system equilibrated above the liquidus. The environment of the mold was next cooled with a controller responding to a differential thermocouple that measured the difference between the temperature of the melt and the temperature of the mold environment. The differential thermocouple consisted of one chromel-alumel junction in the melt connected in opposition with a second junction in the furnace. The potential across the differential thermocouple was input to the controller which acted to keep this potential at a set. constant value; hence the temperature difference between the two junctions was maintained nearly constant. Major resistance to heat flow in the above apparatus was between the metal surface and the furnace atmosphere, not in the metal itself. By maintaining a constant temperature difference between the metal and the furnace atmosphere, the controller maintained an essentially constant rate of heat extraction during solidification, regardless of amount of heat released by the metal per unit temperature change. When the metal temperature dropped just below the eutectic temperature. the ingot was removed from the furnace and water-quenched. The unidirectionally solidified ingots were cast in a similar mold to the foregoing except that provision was made to extract heat through the bottom face of the mold by passing air or water through the mold base, Fig. 1. For these experiments, metal and mold temperature were again equilibrated above the liquidus. Temperature of the mold environment was then held

Jan 1, 1967