Search Documents

By Sir Robert Hadfield

LAST year this Institute was good enough to accept some remarks by the writer regarding sound steel, entitled Plant for Hadfield Method of Producing Sound Steel Ingots, being a continuation of a research in which for some time the writer has been engaged, and full particulars of which were submitted in papers entitled A New Method of Revealing Segregation in Steel Ingots, and Method of Producing Sound Ingots, read before the Iron and Steel Institute in October, 1912. These papers gave rise to a very interesting discussion, both in England and America. This question is one of vital importance, as unless sound steel in the form of ingots is first obtained, sound steel in the finished forms of rail billets, rails, bars, sheets, and other forms cannot be expected. The working stresses demanded by modern conditions are so great, each year they probably approach nearer to the limit of safety, that without doubt those who produce steel will be compelled to pay the attention which this subject deserves. Moreover, the problem is not an insuperable one, as shown by the writer in the papers above referred to. In view of the information which has already been presented in these papers, it is not now necessary to go into details of the system advocated by the writer, except to repeat that the ingots and steel now referred to were produced by employing in the first place sound fluid steel, free from blowholes, this being poured into ordinary ingot molds, provided with the necessary feeding heads, the insulating slag medium, also charcoal and air blast or other suitable form of applying heat to the head portion of the ingot. Tile upper or head portion of the ingot is kept fluid by the intense heat generated by the air blast and charcoal, so that such fluid steel passes into the body of the ingot below the head, thus feeding and avoiding the shrinkage or piping which would otherwise occur. The result is the production of a sound steel ingot, free from blowholes, segregation and piping, and in which the waste portion, usually termed the discard, is but little over 7 or 8 per cent.

Jan 4, 1914

By R. F. Mehl, G. V. Smith

THE decomposition of austenite in steels, because of its immense practical importance, has been subjected to extensive study in recent years from the point of view of the mechanism of the process.1-3 Although much information has been acquired, a number of questions, principally of theoretical interest, remain. One is that of the atomic-crystallographic mechanism by which each of the various reaction products forms. The isothermal reaction products of the eutectoid decomposition in plain carbon steels (to which this study is restricted) have conveniently been classified in three general groupings-pearlite, bainite, and martensite. Of these several products, pearlite and martensite have been studied extensively, but bainite has received only scant attention. As a result, the mechanism of the formation of pearlite and that of martensite are now fairly well understood while a great deal of uncertainty exists regarding bainite. PEARLITE Pearlite forms from austenite by the precipitation of alternate platelets of cementite and ferrite, which grow into the austenite matrix .2-5 The rate of reaction may be described in terms of a rate of nucleation and a rate of growth.2.3 Mehl and Smith6 have attempted to determine the lattice relationships existing between the ferrite in pearlite and the parent austenite. Using a pole-figure method of analysis, it was found that a limited number of ferrite orientations resulted from the decomposition of a single grain of austenite; it was not possible, however, to decide between two assumed ideal relationships, both of which appeared to account for the experimentally determined pole figure. It was definitely shown, however, that the relationship obtaining was quite different from that determined for the proeutectoid separation of ferrite.7 No attempt was made to determine the habit plane (matrix plane to which the precipitate lies parallel) of the pearlite lamellae. Belaiew8 earlier had stated that the number of directions assumed by the pearlite lamellae in a single grain of austenite was 12 (no details were given) and concluded wrongly, as Mehl and Smiths have pointed out, that the lamellae delineate the [210] planes of ferrite.* MARTENSITE It is known that martensite is a transitional constituent of body-centered tetrag-

Jan 1, 1942

By F. Lynwood Garrison

It is not intended to make in the present paper any deduction or to formulate any theories from the results obtained by experiments. The further expenditure of considerable time and labor would be required to obtain a sufficient basis for positive assertions as to the microscopic structure of the different varieties of iron and steel, and the structural changes which take place in them. It is therefore my purpose at this time to offer simply a synopsis of the general results arrived at in a few months' work, a brief description of apparatus used, and a few hints as to the preparation and preservation of the material which it is intended to investigate. The study of the microscopic structure of iron and steel is not altogether new. Some attention has been given it in both England and Germany. But the foreign publications on the subject have thus far been confined, so far as I am aware, to two papers, one by Herr Martens, of Berlin, contributed to the Verein zur Befoerderuny des Gewerbfleisses and the other a lecture by Dr. H. C. Sorby of Sheffield. Dr. Sorby, it seems, was induced to investigate the subject as bearing on the structure of meteoric iron ; and the results he obtained are certainly very interesting. At the Boston meeting of this Institute, in February, 1883, Mr. J. C, Bayles called attention to the subject in a neat and exceedingly interesting paper, in which the work of Messrs. Martens and Sorby was summarized,* and original suggestions were added. It is at present difficult to say what will he eventually the practical value of the microscope, thus employed, in the sciences of engineering. The role which it seems most likely to play is that of' an adjunct to the testing-machine, and not (as some have supposed) a rival to the chemical laboratory. That it will be a most valuable accessory seems, to say the least, highly probable. I need hardly go at length into the details of preparing the material for examination. Mr. Bayles has described the process in such a plain and comprehensive manner that if his instructions are

Jan 1, 1886

INTRODUCTION IT is 10. years this summer since the first of the contributions which it has been my privilege to make to the working tools of the hydrometallurgist was set at work, but a full description of what has come to be known as "Dorr Machinery" has never been published in the Transactions of the Institute, and it has been suggested to me that an account of the same would prove of interest to members, although most of those engaged in cyaniding and concentration are probably familiar with it. The account which I shall give of the development of the machines must be recognized as being written from the viewpoint mainly of my own local experience and not from that of one who was familiar with the general metallurgical practice throughout the world. Most advances in any art are conceived before the time is ripe for their development and any .invention which comes into general use will usually be found to have been tried out in a crude way and abandoned more than once. If the early experimenter went as far as the Patent Office, his work may serve no other purpose than to prevent the issuance of the broadest patent to those who later may develop a commercial process. The cyanide process in the United States early in 1904 was mainly confined to the leaching of dry crushed ores, both coarse and fine, and sand treatment of tailings from concentration and amalgamation. In the Black' hills some plants were crushing in cyanide solution, leaching sands and handling the slime by the well-known decantation process. Filter pressing, in use for some years in Australia,had been tried in several places in this country and the Moors process had been abandoned at Mercur after' a short run, but was doing good work at the mill of Lindbergh, Dorr & Wilson, at Terry, and being installed at Bodie and the Liberty Bell. A general feeling, however, still existed that, slimes were to be avoided when possible, on account of the losses in treatment and the difficulty of making a good leaching product when they were present in large amounts, especially when the crushing was done in cyanide solution.

Jan 8, 1914

By Don B. Shupe, John K. Berry

The handling and disposal of mine water is a much larger problem than is apparent at first glance. Many more tons of water are removed from underground coal mines in the United States each year than tons of coal. In the old anthracite region of Pennsylvania the average was around 32.7 t (36 st) of water for each ton of coal produced, while bituminous mines average about 4.5 or 5.4 t (5 or 6 st). Water encountered in the mines may come from several different sources. In mines with light cover and without a firm solid roof, rain may seep directly into the workings. This is also true of deeper mines where pillar falls have broken the roof to the surface. The top under creek beds is generally faulty and broken and water comes through the roof at this point. Deeper mines are frequently overlain by water-bearing strata and pillar breaks and faulty top can admit water, while places running to the dip often accumulate water which comes up through the bottom. In all cases, except where passing under a year-round stream, the amount of water made is usually pretty closely connected with the weather-more water during the rainy season, less in the dry, although the deeper a mine is, the longer it is before changes in rainfall are felt. Another source of water, not connected with seasonal changes, is old water, accumulated over a period of time in abandoned workings of the mine, or from flooded adjacent mines. Here the water filters through the coal, the parting, or comes up through cracks in the bottom. Similarly, core holes, drilled to prospect the property, can be a source of unexpected water and modern safety requirements for dust-allaying water at the working faces can turn a pleasant working area into a soggy mess over the weekend if the system is not properly maintained and operated. Why water must be disposed of is obvious. If allowed to accumulate, sooner or later the mine will fill up, or at least it will become "roofed" in low places, blocking ventilation and traffic. It must be controlled long before it reaches this stage. Water standing in the working faces is

Jan 1, 1981

By Clarence A. Seyler

The technical difficulties of cutting thin sections of coal for examination by transmitted light have hitherto restricted the investigation of the important subject of the microstructure of coal to the few possessed of the requisite skill and time. Apart from this, the method fails with anthracites and other coals rich in carbon, owing to the opacity of the material. Occasional use of the method of polishing a surface, with or without etching, has been made, but it was not until Winter' published an account of his results that attention was seriously directed to the method. In May, 1923, a specimen of dull anthracite came into my hands; I tried Winter's method on it and the presence of megaspores and other vegetable structures became clearly visible. A preliminary notice was published by me;2 but I soon abandoned the use of Schulze's solution, having found that a mixture of chromic and sulfuric acids gave far better results. In the meantime Turner and Randall, in America, had independently developed the method of flame etching, as applied to anthracite, with great success. I have spent a year studying the method of chromic etching, which gives excellent results with bituminous coals and camels, as well as with anthracite. For anthracites, I have used the chromic method and Turner's method of flame etching, whichever was the more convenient or as a check one on the other. The polishing is done, according to metallurgical practice, by the use of a polishing machine and successively finer emery paper, followed by polishing on cloth moistened with a suspension of levigated green oxide of chromium, and a final rubbing on "selvyt" (a cotton velvet polishing cloth) moistened with alcohol. The polished sample is examined by reflected light with a 2/3 and 1/6 in. objective. Bituminous coals usually show considerable structure, and even anthracites show it faintly in places. The sample is then etched by immersion in a boiling solution made by adding 10 c.c. of concentrated sulfuric acid to 30 C.C. of a saturated solution of chromic acid; enough water is then added to dissolve

Jan 1, 1925

By Horace Mann

A FEW years ago, it was generally thought that from 15 to 18 per, cent. of zinc oxide was the upper limit of a workable lead blast-furnace slag. With slags above this zinc-oxide content, the furnaces gave so much trouble because of hearth, wall, and crucible accretions that the campaign was very short. The time lost in cleaning out the frozen furnaces, for it was seldom possible to blow them out, and blowing in was so great that it was considered uneconomical to attempt the running of high-zinc slags, even if this were metallurgically possible. It is true that there are, references to one or two slags much higher in zinc than the foregoing,1 but the average smelterman regarded these, as freaks and not to be considered for regular furnace work. One or two plants, notably the plant of the United States Smelting Co, at Canyon City, Colo., ran charges, higher in zinc. At this plant, the zinc-oxide content of the charge was frequently 20 per cent. and higher but the slags from these furnace's seldom ran over 10 to 12 per. cent. zinc oxide. The furnaces were run with a large volume of air under a relatively low pressure, a low smelting column, and a very hot top; as a result, a large amount of zinc was volatilized. Even with the low smelting column and hot top, accretions caused much trouble and barring, down was a daily occurrence. At the time most of the theories on lead blast-furnace work were promulgated or worked out, it was necessary to run a furnace with a cold top in order to avoid an excessive loss due to fines and fume. At the same time, the smelting conditions had to be such that the lead and silver would be reduced and would enter the bullion. The slag had to be liquid but the charge must not give excessive accretions either in the hearth or on the walls of the furnace. This forced the operators to run the furnaces with a comparatively low blast, which, in turn, caused a small fuel consumption per unit of time with the accompanying result of a low working temperature.

Jan 8, 1925

By L. Russell, van Wert

During an investigation in which the solubility relations of the phases in Muntz metal (60 per cent. copper, 40 per cent. zinc) were under study, certain phenomena that had no immediate connection with the main problem were observed, which were thought sufficiently interesting to study further. Because of lack of time, only a preliminary survey was made of two of these; namely, the cleavage structure developed under certain conditions in a 60:40 brass and abnormal grain growth in this alloy. Cleavage Structure in Heat-treated Muntz Metal Carpenter noted many years ago that cold-working a brass of the Muntz metal type, which had been quenched previously from within the beta field, results in a partial breakdown of the supersaturated beta solution and the precipitation of the solute (the alpha solution) in the cleavage planes of the beta grains. This manner of rejection of a solute from a metastable solid solution is not peculiar to this particular alloy, for among others, it occurs in the cold-working of certain austenitic steels; for example, the austenitic nickel steels. In these ferrous alloys, cold deformation produces a partial decornposition of the austenite, with the formation of martensitic "needles" and zigzags in the austenitic poly-hedra. It is interesting to note that while the two solid solutions— austenite and quenched Muntz metal— are metastable and in their mode of decomposition behave quite alike when deformed in the cold, the metastability of each results from a different cause; viz., that of the austenite from the fact that it is a supercooled solution (its solvent. gamma iron, at ordinary temperatures is below its normal stable range whereas the metastability of the quenched Muntz metal is the result of supersaturation. When a 60:40 brass is quenched from above 800" C.—that is, from within the field where the beta phase alone is stable—this solution is retained practically intact and the alloy so cooled is found to consist almost entirely of polyhedra of this solution with only a little alpha present ordinarily at the boundaries of the beta grains—the result of a slight

Jan 1, 1929

By van Wert, L. Russell

During an investigation in which the solubility relations of the phases in Muntz metal (60 per cent. copper, 40 per cent. zinc) were under study, certain phenomena that had no immediate connection with the main problem were observed, which were thought sufficiently interesting to study further. Because of lack of time, only a preliminary survey was made of two of these; namely, the cleavage structure developed under certain conditions in a 60:40 brass and abnormal grain growth in this alloy. Cleavage Structure in Heat-treated Muntz Metal Carpenter noted many years ago that cold-working a brass of the Muntz metal type, which had been quenched previously from within the beta field, results in a partial breakdown of the supersaturated beta solution and the precipitation of the solute (the alpha solution) in the cleavage planes of the beta grains. This manner of rejection of a solute from a metastable solid solution is not peculiar to this particular alloy, for among others, it occurs in the cold-working of certain austenitic steels; for example, the austenitic nickel steels. In these ferrous alloys, cold deformation produces a partial decornposition of the austenite, with the formation of martensitic "needles" and zigzags in the austenitic poly-hedra. It is interesting to note that while the two solid solutions— austenite and quenched Muntz metal— are metastable and in their mode of decomposition behave quite alike when deformed in the cold, the metastability of each results from a different cause; viz., that of the austenite from the fact that it is a supercooled solution (its solvent. gamma iron, at ordinary temperatures is below its normal stable range whereas the metastability of the quenched Muntz metal is the result of supersaturation. When a 60:40 brass is quenched from above 800" C.—that is, from within the field where the beta phase alone is stable—this solution is retained practically intact and the alloy so cooled is found to consist almost entirely of polyhedra of this solution with only a little alpha present ordinarily at the boundaries of the beta grains—the result of a slight

Jan 1, 1929

By R. M. Keeney

Before the outbreak of the war in 1914, the only electric-furnace smelting plant operating on a commercial basis west of the Mississippi River was an electric pig-iron plant in California; rare metal ores were not smelted, concentrates of molybdenum, tungsten, uranium, and vanadium ores being shipped East for reduction. Practically no chrome ore was being mined, and only comparatively small amounts of manganese ore. Today there are two electric smelting plants in California, one in Washington, one in lowa, and four in Colorado; two plants are under construction in California, and one in Montana. Ores of manganese, chromium, molybdenum and tungsten are now smelted in the West, and although uranium and vanadium concentrates are still shipped to the East, they will probably be treated in western plants in a short time. The four electric-furnace plants in Colorado are listed in Table 1. Table 1.—Electric Smelting Plants in Colorado Capacity. Company Location KilowattB PRoductS Tungsten Products Co........... Boulder 800 Ferrotungsten, ferromo- lybdenum. Boulder Tungsten Production Co .. Boulder 400 Ferrotungsten. Ferro Alloy Co.................. Utah Junction 1200 Ferrochrome, ferrotung- sten. Iron Mountain Alloy Co......... Utah Junction 3000 Ferromanganese. Power for all of these plants is supplied by the Colorado Power Co. The plant of the Ferro Alloy Co., at Utah Junction, contains one 750-kw., three-phase furnace, to which power is supplied by three 250-lrw. transformers, connected /Y to give 129 volts on the furnace cables, the transformer ratio being 13,200 to 75 volts. The furnace operates with an actual voltage of 120 volts, and produces about 3 tons of ferrochrome per 24 hr. from 40-per cent. Cr2O3 ore. The furnace consists of a steel shell of circular cross-section, 8 ft. (2.43 m.) in diameter by 7 ft. (2.13 m.) deep, lined with magnesite, and having three vertical carbon electrodes 12 in. (30.48 cm.) in diameter. A 450-kw. furnace, of the same size as the 750-kw. furnace, is also operated on chrome ore. This furnace is three-phase in appearance, but operates electrically as a single-phase furnace. There are three vertical

Jan 1, 1920

By T. Johnston, B. Cox

The results of oxidation and corrosion experiments on niobium in oxygen and steam at temperatures of 350° to 650°C, and in dilute sulphate solutions at 300°C are presented. The oxidation of niobium in oxygen can be explained in terms of a pre-transition period, which obeys an approximately parabolic rate law, and a post-transition period in which a more rapid linear rate is partially stifled by restriction of the gas flow due to the gvowth of the porous outer film. Due to changes in the porosity of the outer layers the restriction presented by the porous outel. film attains a limiting value. Subsequent oxidation obeys a linear rate law and shows an almost linear dependence of the rate on gas pressure. liltimately a second failure of the protective film may take place leading to a further acceleration in the oxidation rate. In water vapor the oxidation of niobium follows a parabolic rate law and does not show a transition to linear kinetics. The higher oxide, Nba05, was usually absent from the NbO/NbO2 film which was formed. The addition of a small partial pressure of oxygen to the water vapo3, resulted in accelerated oxidation according to the normal kinetics for oxidation in oxygen. The oxygen reacted preferentially with the niobium, and the protective oxide film was reformed when all the oxygen had been consumed. This behavior supports the theory that nucleation of Nb205 on the surface of the protective NbO/NbO2 film is the cause of the accelerated oxidation. After oxidation in steam at high-pressure Nb2Os was found in the protective film. The mode of formation of Nb2O5 under these conditions did not produce a change in kinetics, but was thought to explain the comparatively large dependence on pressure of the oxidation rate. The kinetics of oxidation in oxygenated aqueous solutions at 300°C were similar to those for oxidation in oxygen. A penetrating attack on niobium sheet may be related to the second breakaway observed by some investigators of oxidation in oxygen.

Jan 1, 1963

By J. Chipman, N. J. Grant, H. L. Bishop

Lime and dicalcium-silicate crucibles were equilibrated with molten iron and liquid slags containing iron oxide and small amounts of sulfur. The oxygen content of metal, iron oxide activities, and desulfurization values of the slags were determined in the temperature range 1530 to 1700°C. The influence of magnesia in the slag and the temperature dependence of the solubility of lime in liquid iron oxide and the ferric oxide content were established. The temperature contour of the liquidus surface of iron-silicate slags saturated with lime and dicalcium silicate was also established at 1600°C. THE importance of the role that slag composition plays in the refining of steel has been known for many years. Numerous studies have been made using actual plant data in order to establish the relationship between the composition of the slag and metal during the refining of a heat of liquid steel. These results rarely represent equilibrium conditions since completion of the various chemical reactions involved in steelmaking is seldom realized. In order to establish quantitatively the equilibrium conditions existing between the slag and metal, several laboratory studies have been conducted in the past 20 years to determine the reactions important in slag control. These investigations have included studies of simple liquid basic and acid slags as well as more complex slag systems which approach those commonly found during the refining of a heat of steel. Since most of the previous studies of simple basic iron-oxide slags equilibriated with molten iron were made in magnesia crucibles, it was not possible to establish the distribution of sulfur and oxygen between molten iron and slags consisting only of the three essential components, lime, silica, and iron oxide. This investigation was undertaken to establish the equilibrium conditions for simple lime-iron oxide and lime-silica-iron oxide slags. Accordingly, it was expedient to prepare crucibles both of lime and dicalcium silicate to establish the equilibrium conditions between molten iron and iron-oxide slags saturated with the refractory materials and free from other components. The only other studies of the equilibrium between molten iron and lime-saturated slags are those of Fischer and vom Ende, 1, 2 in which the solubility of oxygen was determined in an air atmosphere. The

Jan 1, 1959

By Harry V. Welch

Early in the development of the art of metallurgy, it was noted that a distinct difference existed in the character, collection possibility and health hazard of the "smoke" from lead furnaces and those from copper plants. Zinc-plant fumes, although not so detrimental to health, were closely allied in nature to those of the lead works. In Cottrell plants, there are sufficiently distinct differences in operation and amount of construction between those for lead and copper to justify their consideration under separate headings; therefore, while the application of the process at copper-reduction works was covered by the writer some two years ago in the Transactions1,† this discussion will confine itself more distinctly to "fume" collection. General information on the process has been presented in numerous articles and by many authors: Cottre112, Schmidt3, Bradley4, Anderson6, Labbe6, Shiga7, Rathbun8. "Fume" may be defined as material, metal or nonmetal, elemental or compound, evolved as a vapor from a furnacing or chemical reaction and condensing, chilling or reacting within the gas stream to yield a solid form, and in this definition liquid particles are solids in a sense as distinguished from gases or vapors. Such condensed particles are of minute form, on the order of "smoke," and, for example, on the order of a few hundredths of 1 micron (1 micron = 1/25,000 in.) to perhaps 3 microns, with agglomerates, in relatively small proportions of many particles. Metallurgically typical fume products are lead compounds, oxides, carbonates and sulphates; elemental zinc, more commonly encountered as a fume particle of zinc metal with a surrounding "skin" of zinc oxide; arsenic, both metal and oxide and some of its more complex salts such as added sulphates as found in flue dusts; antimony, more particularly its oxide forms; and elemental sulphur, sometimes a troublesome product, in Dwight-Lloyd sintering-plant fumes. These products, particularly the elemental or lower oxide forms, have relatively appreciable vapor pressures at the existing operating temperatures as reported by Welch and Duschak9, Ingold10, Johnstonll, Millar12,13.

Jan 1, 1937

By William G. Kegel

Apart from a usable product and good mining conditions, the greatest asset for a profitable coal mining organization is an effective mine maintenance program. The first step in achieving this is to have good mechanics-or men who want to be mechanics and are interested in knowing, more about the design and control of the machines in their charge. A good mechanic's knowledge and ability result from ambition, curiosity, and determination. Starting with these qualities, the aspiring mechanic can launch his career by learning all he can about mechanics, electricity, and hydraulics. Though the path is rough, the end result is rewarding. Mining machinery probably receives as much, if not more, abuse as any other heavy equipment in use today. Considering the conditions under which much of the repair work must be done, it is essential that the mine operator has the best men and tools to perform the work. Mining machines, from their inception, have utilized the electric motor; and down through the years of mechanization, this power source has undergone many changes to better adapt it to the job. The first motors used were direct-current (d-c) motors since d-c power was the most economical power source for mining at the time of early mechanization. These motors were large open-type machines which are seldom used in modern mining. Because of the mine environment, the d-c motor has been reduced in size to better suit the application in mining machines and is now manufactured with dust-tight or explosion-proof enclosures. The d-c motor is constructed with either (or both) series and shunt fields located on the stationary part of the motor (stator) and an armature coil wound on the rotating part of the motor (rotor). Power is supplied to the armature by brushes which are held stationary and make sliding contact with the armature. The brushes requires regular and careful maintenance because worn or defective brushes will cause heat or arcing which can destroy the motor. D-c motors can be used as d-c generators when mechanical power is supplied to them by the rotating

Jan 1, 1981

By George Rice

THE subject of dust explosions in coal mines first appears in the Transactions of this Institute following the first great mine disaster that happened in bituminous mines of the United States. This was the Pocahontas explosion, which occurred Mar. 13, 1884, causing the loss of 112 men. The operating company wisely asked the technical assistance of the Institute, requesting that a committee be appointed to investigate and report. This committee consisted of Messrs. Bramwell, Buck, and Williams, who, after careful study, reached the conclusion that the explosion was due "either to dust alone or to dust quickened by an admixture of fire-clamp too slight for detection by ordinary means." This is perhaps the first time in this country that coal dust was considered to be the chief agency in a mine explosion.. The report is given in the Transactions, vol. xiii, p. 237 (1885). It is particularly worthy of note that the committee called attention to "the necessity of full-sized tests and systematic experiments. " In the same volume of the Transactions, there is a most interesting paper reviewing the literature relating to coal dust, by E. S. Hutchinson, entitled Notes on Coal-Dust in Colliery Explosions. Mr. Hutchinson gives a historical account of observations on the part played by coal dust in mine explosions, beginning with Messrs. Lyell and Faraday's report on the Haswell colliery explosion in 1844, in which it is said "much coal gas had been made from this dust in the very air itself in the mine by the flame of the firedamp, which raised and swept it along, and much of the carbon of the dust remained unburned only from want of air." The subject lay dormant until 1875 when William Galloway began some coal-dust experiments in a small gallery at a mine in South Wales of which he was manager. At that time he considered the presence of firedamp necessary for continued propagation of a dust explosion; but in 1884, the year of the Pocahontas disaster, he stated that no earlier author-than himself had credited coal dust with being a principal factor in mine explosions, relegating firedamp to a secondary place.

Jan 10, 1914

By P. B. Bucky

IN previous publications1 it was shown that a scalar model of any weighty structure, where the stresses produced are mainly due to gravita-tional forces, will behave similarly to its prototype if the model and proto-type material are the same arid the model is placed in a centrifugal field of force (substituted for the gravitational field) which has been increased in the same proportion as the linear model scale is decreased. This principle is now being applied to a study of the behavior of mine structures in an attempt to determine the laws that control them. The importance of using models as a means of solving mining problems has been discussed previously, yet it may be well to reiterate here that this method of research and type of solution have been productive of far-reaching results in other engineering fields, notably those of hydraulics and aerodynamics. Model research is a comparatively cheap and time-saving method of checking practical experience. Up to the present time the best guide to what will happen underground has been the judgment of the man who has observed most and been longest acquainted with the local conditions. His experimental work underground is limited by the elements of cost, time and danger, while failure is seldom permissible. In a model, as in a test tube, all elements that affect the solution of a problem are under definite control. Each element may be varied independently at will and its effects noted. Experimental work on a small-scale model may there¬fore be performed at a comparatively small expenditure of time and money, instead of on a full scale in the mine, where the cost, time, and danger elements are necessarily great. The experiments described in this paper are to be considered as part of a progress report and a continuation of Technical Paper 425. One object of the research program is to make each experiment point the way for further research on that particular phase of the general problem. The results and conclusions presented here are therefore not to be considered as final, but are to be interpreted as

Jan 1, 1933

By David R. Mitchell, B. M. Bird

DENSE-MEDIA processes utilize the familiar laboratory float-and-sink procedure on a commercial scale. Just as wood chips float on water and sand sinks, so coal floats and refuse sinks when placed in a medium intermediate in specific gravity between the coal and refuse. Liquids intermediate in specific gravity between coal and refuse used in commercial plants are of four types: (1) organic liquids of high specific gravity-halogenated hydrocarbons; (2) dissolved salts in water; (3) pseudo liquids obtained by suspending solids, such as sand or magnetite, in water, and, (4) fluidizing a mass of sand or other solids by air currents. Those most widely used for cleaning coal are solutions of calcium chloride in water and a suspended sand or magnetite pseudo liquid. Laboratory float-and-sink testing is an intermittent operation during which every opportunity is given for particles lighter than the medium to float and particles heavier to sink. Commercial processes are continuous; vertical and horizontal currents of the separating medium occur as either part of the process or unavoidedly produced by the introduction of feed and withdrawal of products, 'so that the exact separation of the laboratory technique is not duplicated by commercial processes. However, separations close to the theoretical are obtained in commercial machines by careful technical control of the process. Most machines in commercial installations are crowded to get as much out of the equipment as possible, so that careful technical control is necessary is get the recoveries and grade of product desired. Sizes usually cleaned are plus ¼ in. or plus 1/8 -in. in the United States and plus 1/16-in. in Great Britain. Coal as small as 1 mm. has been cleaned in some experimental installations. The separation of coal from refuse in sizes finer than about 1/8-in. is made difficult by viscosity effects and hence at the present time cleaning is confined to the coarser sizes. Technical advances in the art of cleaning coal by dense-media processes is progressing rapidly and it is likely that equipment, media, and procedures will be developed to clean sizes down to 0.5 mm. efficiently and at low cost.

Jan 1, 1950

By E. L. Mann

Asbestos is the generic name given to a group of fibrous mineral silicates found in nature. They are all incombustible and can be separated by mechanical means into fibers of various lengths and cross sections, but each differs in chemical composition from the others. The commercial grades of asbestos consist of a spectrum of lengths and sizes and are not definitive as are most organic fibers. It is generally recognized that there are two main groups of asbestos. The first only contains the fibrous serpentine called chrysotile and comprises about 94% of the world production of asbestos. The second group contains five minerals in the amphibole series-crocidolite, amosite, anthophyllite, tremolite, and actinolite. The latter two have no commercial importance. Properties Physical The structures of asbestos fibers have been studied intensively over a number of years. X-ray diffraction patterns have been used as a means of identification and classification. Low angle X-ray scattering techniques have shown that chrysotile fibers are "hexagonally close packed" and parallel to each other, having cross-sectional diameters varying from 18Å to 300 Å units, while the amphibole fibers are many times larger in cross section, have considerably smaller surface areas, and the fibers are less symmetrical than those of chrysotile. Electron micrographs of the more common types of asbestos are shown in Figs. 1-4. Fig. 1 illustrates the softness and flexibility of chrysotile which make it suitable for textile-type products. For a number of years there was considerable controversy over the exact nature of chrysotile fiber, but the photographic evidence in Figs. 5-7 clearly show that it is tubular in structure. The curvature is the result of the mismatch in the dimensions of the silica [Si2O5] and brucite [Mg(OH)2] layers which are on the inside and outside, respectively, of a double sheet. This curvature had been predicted by Pauling (1930) years ago based on the molecular dimensions of the two component structures. In contrast to this, the structure of the amphiboles consists of two ribbon chains based on Si4O11 units separated by a band of seven cations with two hydroxyl groups attached to

Jan 1, 1983

By T. L. Joseph

The extent to which hot metal from the blast furnace affects open-hearth practice and the quality of steel produced has been discussed widely. Open-hearth operators have attributed difficulties experienced in making satisfactory steel to characteristics of the pig iron not disclosed by ordinary analysis. The commonest criticism of the iron has been that it is "physically cold" or "dirty." Often when the blast furnaces are working irregularly the quality of the iron is questioned. A cold hearth, slipping and hanging, the use in the past of unsintered flue dust, and the use of ores difficult to smelt have been associated with the production of iron of poor quality. The difficulty of the situation is that we have no proven yardstick for quality aside from ordinary analysis. Uniformity in analysis is recognized as being important, but the difficulty of changing the open-hearth practice when the iron analysis varies widely may not always be fully appreciated. Although the problem of correlating the characteristics of steel with those of pig iron is admittedly obscure, the effort of producers of quality steel to investigate all factors that may have a bearing on the final product is justified. This report contains data on the oxides in several hundred casts of basic iron produced in a furnace during the course of normal operation on Lake ores. Incidental to the study of the oxides in the iron, it was desirable to follow closely the temperature of the iron. The effect of temperature of the iron upon the silicon and sulphur present is discussed. A general relation between the basicity of the slag and the sulphur in the metal was developed. The amount and composition of oxides in the hot metal and in the steel bath during various intervals between melt-down and tap are discussed. Heats of rimmed steel, killed steel, and semikilled steel were investigated. The hot metal on individual heats was either all taken from a mixer or consisted partly of direct metal and partly of metal from the mixer. Samples of the iron for oxide determinations were

Jan 1, 1937

By T. D. Yensen

It is safe to say that of all the different materials that go to make up electrical machinery, iron is the most important. Upon its magnetic and electrical quality depends not only the efficiency of the machine but, to a very large extent, the cost. Aside from the mechanical strength, there are three characteristics of iron that are of importance in this connection, viz., magnetic hysteresis, electrical resistance, and magnetic permeability. In the homopolar machine, where the magnetic flux is unidirectional, permeability is the only important factor, but in all other machines the flux is reversed in one or more parts and causes losses due to hysteresis and eddy currents. The eddy-current loss depends largely upon the electrical resistance of the iron; the higher the resistance the lower the loss, under otherwise identical conditions. These hysteresis and eddy-current losses cause heating of the machine, and as they depend upon the magnetic density in the iron, this density must be regulated so that the heating shall not be excessive. If the hysteresis and eddy-current losses and the permeability of the magnetic circuit will permit an increase in the magnetic density, or, in other words, a decrease in the amount of iron, this in turn will mean a decrease in the amount of copper needed, with a consequent decrease in the copper loss. It is thus seen that, indirectly as well as directly, the above characteristics have an important bearing on both the efficiency and the cost of electrical machinery. In general, it may be said that iron for electrical machinery should have the following characteristics: (1) low hysteresis loss, (2) high electrical resistance, and (3) high permeability. These are the characteristics that investigators have been striving to attain since electrical machinery first came into use. Until the beginning of the present century, Swedish charcoal iron was regarded as the best grade of iron for magnetic purposes, and even now it ranks high among the various grades used. About that time Sir Robert Hadfield1 produced a number of iron alloys that revolution-

Jan 1, 1916