Search Documents

By Richmond Bennett

Airborne geochemistry became a reality with the advent of a high-sensitivity air¬borne gamma ray spectrometer with large volume NAI(Tl) crystal detectors. The high-sensitivity spectrometer measures small variations in the concentration of potassium (as Ks°), thorium (as Tl308) and uranium (as Bi.214) along the flight lines in the area surveyed. Hydrothermal dispersion patterns are indicated by anomalous measured values of the concentrations of potassium, thorium, uranium, or their ratios. In two recent Australian survey areas, copper mineralization was located along favorable structures within hydrothermal dispersion patterns delineated by airborne geochemical surveys. In metamorphic terrane where there had been po¬tassium metasomatism, the hydrothermal dispersion patterns were indicated by high potassium/uranium ratios (K40/Bi). In a sedimentary environment that had been intruded by a stock, the path of hydrothermal fluids was indicated by uranium (Bi214), thorium (TV'), and uranium/ thorium (Bi214/Tl208) ratios.

Jan 1, 1972

By Robert M. Rudio

Montana is leading the way in the field of mined-land reclamation with new laws and new ideas. The Montana Department of State Lands is combining new legislation and practical application techniques to all mining operations in the state. Road building, stream relocations, or settling systems can be designed to meet the environmental problems. Mineral exploration now requires a new and closer look at drill site locations, road gradients, and exploration tools. The problems and costs of land rehabilitation must be thoroughly understood by the exploration geologist in order to satisfactorily conduct exploration in Montana.

Jan 1, 1975

By Shiou-Chuan Sun

Most previous work on sedimentation of coal1 and mineral2,3 suspensions has been conducted in graduated 1-liter glass cylinders of 6-cm diam. With this type of large container it is often difficult to see through the suspension and tedious to perform a large number of tests. Furthermore, the heavy glass walls and the graduation lines of glass cylinders cause internal and stray reflections, respectively. To obviate these difficulties, an Atlab Emulsion Viewer from Arthur H. Thomas Co. was adopted as an alternative apparatus. Equipment: The viewer,4 shown in Fig. 1, consists of: 1) a stainless steel frame rack holding 21 flat-bottom Nessler tubes or an ungraduated replica 1.64 cm ID and 1.80 cm OD, 2) a movable masked 150-w lumaline lamp behind the tubes, and 3) a scaled glass panel with 100 vertical divisions in front of the tubes. The tubes are snugly held by springs in slots formed by spacer bars, which also serve as shields to eliminate stray light. The lumaline lamp is mounted behind a slit in a movable housing so that it can be positioned behind the suspension to be examined. The lowest or 100-division line on the front glass plate is leveled with the upper side of the bottom of all tubes. The scaled portion of each tube, roughly 19 cm high and 40 ml in volume, is used to study coal and mineral suspensions.

Jan 1, 1959

By James W. Lower

IN developing the orebody on lower levels of the Star mine at Burke, Idaho, Hecla Mining Co. is faced with a serious problem in driving raises. Levels are at 200-ft intervals. As a raise is being driven between levels, at points about 70 and 130 ft from the sill, heavy pressure arches develop and the raise becomes extremely hazardous. Eventually, following a blast, caving occurs, making it impossible to recover the raise. In February 1957 it was decided to attempt sinking a small winze on the vein from the 5500 to the 5700 level. This shaft (winze-raise No. 2) was to be used as a raise prior to stoping. It was assumed, and correctly, that the heavy ground pressure could be controlled by timbering close to the bottom after each advance.

Jan 7, 1958

By D. C. Seidel, E. F. Fitzhugh

Nickel sulfide ores lend themselves readily to concentration before smelting or pressure leaching, but neither of the major oxidized ore types-the iron-rich laterites and magnesium-rich, soft silicates-has been directly concentrated. Upgrading of crude ore in current practice is limited to cobbing lumps of the harder, lower grade rock (protore) from the softer, enriched silicate ore, because only a small percentage of the nickel in these ores occurs in discrete, contrasting mineral particles. There is no apparent mineralogical contrast in the superficial, iron-rich lateritic ores and, in fact, there is no firm assurance that the nickel atoms are within the lattices of the limonite minerals, or else irregularly adsorbed on the limonite. Within underlying, "rotten rock" silicates, occasional veinlets of garnierite and related nickeliferous silicates are found.1 The garnierite veinlets are only incidental, and the majority of the nickel atoms occur as erratic replacements of magnesium atoms in the micaceous chlorites of the ore mass.

Jan 4, 1968

By W. C. Dickerman, J. F. Thornton

TOTAL global war is making extraordinary demands on the oil industry. Huge quantities of 100-octane gasoline, extreme service lubes, toluene and other miscellaneous products are required. 100-octane gasoline is blended from isopentane, base stock, and alkylate. Isopentane is fractionated from natural or refinery gasoline; but since only limited quantities of base stock can be made in this way, catalytic cracking is rapidly becoming the major source of base stock. Alkylate, the most important component, is synthesized from isobutane and an olefin. Extraordinary demands are forcing the full utilization of all present sources and the development of new supplies of feed stocks. Fortunately, the United States finds itself with well-developed processes already available, and this is true of the manufacture of lubricating oil as well. Toluene is now being produced by new methods from special cuts fractionated from selected crudes or from catalytically processed naphthas. Designers of refinery equipment are modifying past practices to conserve every bit of material possible.

Jan 1, 1942

By Walter Miller

Developments in oil refining were so varied during 1938 that a refiner had to be alert or be left behind. The long-talked-of conversion of oil refining into a true chemical industry using petroleum as a raw material was hastened, particularly in the realm of motor-fuel manufacture, by the increased understanding and use of catalytic processes. The petroleum refiner's vocabulary has been extended to include alkylation, cyclization, aromatization, and isomerization. There are other devel: opments of a similar nature, but these are now considered commercially feasible under proper conditions. New Equipment Less expensive equipment and processes encouraged new construction and replacement. Estimates of money spent in the United States on building new plants and remodeling existing installations during 1938 place the sum at not less than $200,000,000, a noteworthy amount in a year marked by a business recession. The commercial application of small-scale catalytic polymerization of refinery gases made one of the latest advances available to the smaller operators, who usually are faced with unit installation and production costs higher than the large refinery enjoys. Competition was thereby fostered. Outstanding in this respect was the construction of two or more polymerization plants in small refineries at extremely low installation costs, with amortization measured in months instead of years. Houdry Processes Bursting like a bombshell late in the year was the disclosure of the extent of the development of the Houdry processes of catalytic cracking, viscosity breaking, gasoline treatment, desulphurization, and polymerization, said to be applicable to almost any raw petroleum stock and yielding gasoline of exceptionally high octane number. This process is claimed to be particularly adapted to once-through cracking of aliphatic hydrocarbons, and when combined with any of the conventional thermal

Jan 1, 1939

By Walter Miller

Developments in oil refining were so varied during 1938 that a refiner had to be alert or be left behind. The long-talked-of conversion of oil refining into a true chemical industry using petroleum as a raw material was hastened, particularly in the realm of motor-fuel manufacture, by the increased understanding and use of catalytic processes. The petroleum refiner's vocabulary has been extended to include alkylation, cyclization, aromatization, and isomerization. There are other devel: opments of a similar nature, but these are now considered commercially feasible under proper conditions. New Equipment Less expensive equipment and processes encouraged new construction and replacement. Estimates of money spent in the United States on building new plants and remodeling existing installations during 1938 place the sum at not less than $200,000,000, a noteworthy amount in a year marked by a business recession. The commercial application of small-scale catalytic polymerization of refinery gases made one of the latest advances available to the smaller operators, who usually are faced with unit installation and production costs higher than the large refinery enjoys. Competition was thereby fostered. Outstanding in this respect was the construction of two or more polymerization plants in small refineries at extremely low installation costs, with amortization measured in months instead of years. Houdry Processes Bursting like a bombshell late in the year was the disclosure of the extent of the development of the Houdry processes of catalytic cracking, viscosity breaking, gasoline treatment, desulphurization, and polymerization, said to be applicable to almost any raw petroleum stock and yielding gasoline of exceptionally high octane number. This process is claimed to be particularly adapted to once-through cracking of aliphatic hydrocarbons, and when combined with any of the conventional thermal

Jan 1, 1939

By Frank D. Hoyt

BY far the most conspicuous of the Pennsylvania slate districts is that extending from the New Jersey line at the Delaware Water Gap westward almost to the Schuylkill River. This covers parts of three counties in east-central Pennsylvania: Northampton, Lehigh, and Berks. The most important development, both in geographic size and product importance, is in Lehigh and Northampton counties. The greater part of the region is underlain by only one formation-the Martinsburg, consisting of slates, clay slates, and sandy shales, all of the Ordovician period. The slate-bearing Martinsburg formation is underlain by Cambro-Ordovician limestones. Immediately overlying the Martinsburg formation is the Tuscarora quartzite of the Silurian period. The Martinsburg formation itself is divided into three distinct divisions, termed simply: the upper, the middle, and the lower members. Commercial slate has been extracted from all of these members, but the formation of greatest importance is the upper member, representing 2600 ft of the total formation thickness of nearly 11,000 ft. The upper member is commonly referred to as the "soft slate" and consists of three facies: 1) beds of blue-gray, very sandy, almost quartzitic slate, in many places, approximately a medium-coarse sand- stone with calcareous cement; 2) blue-gray sericitic slat-the dominant rock type of this member-with occasional chloritic beds; and 3) dark gray or virtually black, highly carbonaceous beds, referred to locally as "ribbons."

Jan 8, 1958

By Alden Emery

SHEET-ASPHALT paving mixtures are composed of three constituents: sand, mineral filler and asphalt. An average composition of such a mixture is sand 75 per cent, filler 15 per cent, and asphalt 10 per cent, figured on a weight basis. The structural strength of the mixture at normal or high temperatures depends mainly on the mineral aggregate (sand and filler), which consti-tutes the entire framework. The filler is the finely divided mineral matter largely passing a 200-mesh sieve, added to carry the sand grading down into infinitely fine particles and so reduce voidage and increase density. The asphalt imparts cohesiveness and tensile strength, gives a certain degree of plasticity, and waterproofs the mixture.

Jan 1, 1933

By H. M. Howe

It is a grave objection to the present system (or rather lack of system) of mineralogical nomenclature that, in the very great majority of cases, the name of a mineral gives no hint of its chemical composition, one might almost say no suggestion, however faint, of anything connected with it or characteristic of it, chemical, physical, historical, geographical, geological, or lithological. In becoming acquainted with a mineral, in addition to learning its composition and important characteristics, one must also learn a name wholly unconnected with any of them. It has occurred to me that a system might be devised in which the name of each mineral should express at least an approximation to its ultimate composition. It is far easier to learn the names of most minerals than their compositions. Most of us are familiar with the names and appearance of many minerals, especially among the silicates, of whose compositions we have but a rough notion. It would be the aim of such a system to enable us, in making the one slight effort of learning the name of a mineral, by that same effort and involuntarily to learn its composition, which now requires an additional and a much greater effort. I have worked out a system designed to meet this requirement, and its description occupies the remainder of this article. Doubtless there are many devices on which could be based other systems fulfilling the requirement above set forth better than that about to be described does, and at the same time furnishing names

Jan 1, 1884

By A. E. Gibson

A new feature in coal mining, where the coal is to be conveyed from a high to a lower elevation and the topography of the country is such as to preclude surface haulage.

Jan 1, 1915

By Shun-ichi Satoh

THE electric arc welding of cast iron has been studied by Braune, Lamberton, Schimpke, Kenyon, Gale Manufacturing Co., Wedemeyer, Candy, Neese, Miller, Carter, American Welding Society, Namack, Lebrun, Achenbach, Jansson, Kochendörffer and others.1 The writer of this paper has been able to obtain a series of cast irons, from gray to white, without using cast-iron electrodes but by coating on wrought-iron bars mixtures of carborundum (SiC) and graphite (C). In this work, he has found the curious phenomenon of barium- carbonate.

Jan 1, 1929

By J. C. Kerkering, P. M. Daling

This paper discusses a study performed to evaluate the feasibility of transferring formal system safety assessment technology to the mining industry. A representative listing of formal techniques was evaluated to select the most useful methods for the mining industry to implement. Criteria for selecting methods included the interests, needs, and requirements of mine safety officials. This paper describes one of the selected methods, preliminary hazards analysis (PHA), and illustrates the analysis procedure for a mining example. This study also includes an assessment of the adaptability of selected methods to a user-interactive computer system for use by mine safety personnel. This paper includes a description of a conceptual computerized PHA-type safety program that facilitates performance of the safety analysis and can accommodate updates and revisions as necessary.

Jan 1, 1983

By B. P. Bellport

When tunneling crews set world records in rates of advance by boring up to 403 ft in a single day and 6851 ft in a month, then the age of rapid under- ground excavation is near at hand with its attendant economies. Boring machines excavate tunnels with uniform diameters and smooth walls and only about 5% overbreak compared to 20% overbreak experienced by conventional drill-blast methods. This advantage minimizes the concrete required for lining and because a circular section is more nearly self-supporting there is less of a need for supports before the concrete is placed. In addition, laser beam guidance improves the accuracy of excavation with boring machines. In the first successful application of laser guidance for boring machines in the Navajo Indian Irrigation Project, the final excavation was within 5/8 in. of the established line and grade over a 10.079- ft advance.

Jan 1, 1971

By D. E. Pickett, E. G. Joe

In accordance with good industrial practice, Canadian metallic-ore concentration plants have always recycled a high proportion of process water to save reagents, save power, conserve water resources, and to protect the community water supplies, to give only a few reasons. In the last few years there has been awakened public concern for the environment and, consequently, government regulations have been added as additional reasons. Present recycling practices are summarized as a basis for improved plant design and operating procedures and for further research. In addition, an attempt is made to determine why plants do not recycle water in certain situations. Although not all Canadian mills are covered, the many examples given indicate the problems and the effort being made to solve them. Wherever available, the chemical quality of the water and the process requirements are indicated as well as the other parameters affecting water recycling at each operation.

Jan 1, 1975

By H. Rush Spedden, Arvid Thunaes

R. R. Knobler and F. E. Albertson—Following the testwork done by Thunaes and Spedden, a Sullivan deck plant was built for the Colquiri mill. This plant started to operate in April 1945 and continues in successful operation. Since May 1950 the Colquiri mill has operated with a completely revamped flowsheet at a rate of 1000 tons per day. The old Sullivan deck section was retained with this new flowsheet. The "slime plant" in Colquiri consists of one 12-cell Denver No. 18-Sp. Sub-A flotation machine, one 16-ft and one 12-ft hydroseparator, six five-deck Sullivan-frames and six shaking tables for cleaning up the Sullivan deck concentrates, as well as 12 Deister plus three Plat-O tables on which the fine sands, which are not treated on the S-decks, are concentrated. Only —325-mesh fines are treated on the Sullivan decks. The combined hydroseparator overflows are fed to the S-decks. From 1946 to 1949, i.e. with the "old" flowsheet and an average mill feed of 800 tons per day an average of 45 tons per day was treated on four Sullivan rougher frames. The two additional frames were used as cleaners. At times, up to 90 and 120 tons of slimes were treated successfully on this Sullivan deck installation. The average operating data for the S-deck section in Colquiri for the year 1949 were as follows: The tests reported in this paper indicated a tin recovery of 42 pct. The actual plant results for 1949 show a 54 pct tin recovery from the Sullivan decks. The total average quantity of tin produced from the S-deck section in 1949 was 15 tons of tin per month. This corresponds to 3 pct of the total mill recovery. The difference between the 6 pct overall recovery-increase expected after the tests in 1943 and the actual plant results given for 1949 is explained as follows. According to the tests, a total of 170 tons was expected to be routed to the Sullivan decks, but because of certain changes in the flowsheet and mill amplifications,

Jan 1, 1951

By H. Rush Spedden, Arvid Thunaes

R. R. Knobler and F. E. Albertson—Following the testwork done by Thunaes and Spedden, a Sullivan deck plant was built for the Colquiri mill. This plant started to operate in April 1945 and continues in successful operation. Since May 1950 the Colquiri mill has operated with a completely revamped flowsheet at a rate of 1000 tons per day. The old Sullivan deck section was retained with this new flowsheet. The "slime plant" in Colquiri consists of one 12-cell Denver No. 18-Sp. Sub-A flotation machine, one 16-ft and one 12-ft hydroseparator, six five-deck Sullivan-frames and six shaking tables for cleaning up the Sullivan deck concentrates, as well as 12 Deister plus three Plat-O tables on which the fine sands, which are not treated on the S-decks, are concentrated. Only —325-mesh fines are treated on the Sullivan decks. The combined hydroseparator overflows are fed to the S-decks. From 1946 to 1949, i.e. with the "old" flowsheet and an average mill feed of 800 tons per day an average of 45 tons per day was treated on four Sullivan rougher frames. The two additional frames were used as cleaners. At times, up to 90 and 120 tons of slimes were treated successfully on this Sullivan deck installation. The average operating data for the S-deck section in Colquiri for the year 1949 were as follows: The tests reported in this paper indicated a tin recovery of 42 pct. The actual plant results for 1949 show a 54 pct tin recovery from the Sullivan decks. The total average quantity of tin produced from the S-deck section in 1949 was 15 tons of tin per month. This corresponds to 3 pct of the total mill recovery. The difference between the 6 pct overall recovery-increase expected after the tests in 1943 and the actual plant results given for 1949 is explained as follows. According to the tests, a total of 170 tons was expected to be routed to the Sullivan decks, but because of certain changes in the flowsheet and mill amplifications,

Jan 1, 1951

By Bjorge, Guy N.

MINING method improve through the gradual process of evolution and in 1340 there were no marked outstanding innovations. On the other hand refinements of detail and betterment: in equipment design continued to progress. Among the most important changes have been the increased application of trucks and highway equipment, including tractors and bull- dozers, to open-pit mining as exemplified by Phelps Dodge's Morenci operations; the Mesabi iron range; and the Tri-State district. Mass or bulk handling contributed its part underground with slurhers and conveyors at Consolidated Coppermines and slushers at Climax; and in open-pit mining. conveyors found increased use on the Mesabi range.

Jan 1, 1941

By W. S. Morris

PETROLEUM'S importance in World War II can perhaps be better realized by the recitation of a few facts and figures: Gasoline needs in this war are already eighty times greater than in the last war. It takes nearly three pounds of gasoline to deliver one pound of bombs, filled with petroleum explosives, on an enemy objective. Every American soldier overseas requires an average of more than fifty gallons of petroleum products per week, with the oil used by Navy and supply ships and America's Allies boosting the consumption of oil per soldier to an even higher figure. Every oil well in the United States now must produce each day an average of four barrels of oil for war and combat jobs. More than fifty million gallons of gasoline, fuel oils, lubricants, and other petroleum products are now going directly to the fighting forces every day.

Jan 1, 1945