Search Documents

By H. R. Froning, R. O. Leach

In wertability alteration flooding, a chemical agent is rnoved through a reservoir by the flood water to increase oil recovery by decreasing the degree of wetting of the rock by the oil. Substantial amounts of the chemical may be lost during movement through the reservoir. The extent of the loss, and therefore the economics of the process, depends in some cases on factors which are difficult to reproduce in the laboratory. Therefore, a short-duration, low-cost field test method is needed to permit evaluation of chemical requirements under actual field conditions. This paper describes a small scale rest conducted at a single well for measuring chemical requirements, thereby giving a more reliable evaluation of this important factor in the applicability and economics of the process. In the rest a small wafer slug containing the chemical agent and a nonadsorbed tracer is displaced into the reservoir by a known volume of wafer. The well is then placed on producrion. Chemical loss per barrel of pore volume contacted is calculated from [he fractional recoveries of the agent tested and the nonadsorbed tracer. The method has been used to determine within the actual reservoirs the chemical requirements for both a sandstone and a dolomite reservoir. Several chemical agents are potentially available for wettability alteration flooding, although none is universally applicable. For some applications of the method, chemical costs per barrel of additional oil recovered can be substantially less than one dollar. INTRODUCTION Wettability alteration flooding provides a means of increasing oil recovery from reservoirs by decreasing the degree of wetting of the rock by the oil and increasing the displacement efficiency of the flood water. Earlier studies demonstrated a relationship between oil recovery during waterflooding and the degree of wetting of a rock surface by an oil. The application of wettability alteration flooding to the Harrisburg field of Nebraska provided a field test' of this recovery process. Subsequently, additional laboratory and field tests have developed additional procedures for evaluating wettability alteration flooding, and have indicated where the process may be applicable. Applicability of this process to specific reservoirs is determined by a progression of tests to determine sus- ceptibility of the reservoir to alteration of its wettability, to indicate the degree of recovery improvement and to estimate the amount of chemical required to process the reservoir. The economics of applying improved oil recovery processes depends not only upon the degree of improvement in oil recovery achievable by the process but also upon the process costs and the timing of the income and the investment. Emphasis in this paper is on the expenditure aspects of the process. The work reported in this paper indicates that the chemical investments required for wettability alteration flooding are substantial. For evaluating the economics of a potential flooding application it is imperative that a sound estimate of the chemical requirements be made for the reservoir. Generally, true reservoir conditions are not adequately simulated in laboratory chemical propagation tests. Because of wide well spacings, many years might be required to obtain chemical propagation data from conventional pilots or inter-well tests. Consequently, n short-duration, low-cost method is needed to determine chemical requirements in the field. The potential applicability of wettability alteration flooding is discussed, as well as the economics of wettability alteration with respect to the inherent and imposed restrictions on the timing of income and investments. DETERMINATION OF CHEMICAL REQUIREMENTS In the process of moving a chemical bank through reservoir rock, some of the chemical agent lags too far behind the flood front to be effective or is otherwise lost to the reservoir system. The extent to which these losses occur overshadows the reductions in chemical concentration due to diffusion and to mixing with the reservoir fluids. Experience indicates that almost without exception, chemicals which induce a wetting change undergo either sorption reactions or chemical reactions with mineral constituents of the pore surfaces. Other reactions may occur between the added chemical and the reservoir oil and water. Even in limiting consideration to reactions of the relatively inexpensive inorganic salts, bases and acids, the reactions may be exceedingly complex. Reservoir pore surfaces consist of more than silica in sandstone reservoirs, and more than calcite or dolomite in carbonate reservoirs. Many mineral species are present, each exhibiting specific tendencies to react with an injected chemical. The reactions which occur can consume enough of the agent to have an important effect on economics. These reactions can cause a change in pH of the chemical bank, or may remove some of the active chemical by precipitation, adsorption or reaction to form a new chemical which may or may not be effective in

By William B. Plank

IN this paper are presented the results of a complete statistical survey of the enrolment, courses and degrees, and the employment situation of recent graduates in all of the 46 institutions in the United States, including Alaska, and four of the six schools in Canada that grant degrees in mineral technology. The data were collected by the writer by means of a questionnaire in December, 1933, to which all the institutions, except one, replied. Included also are data of a similar study made by the writer in May, 1933, for the S. P. E. E. summer session of mining and metallurgical teachers at the University of Wisconsin and published in the Journal of Engineering Education for December. 1933. Some of the data of a paper of the writer's entitled, "The Trend of Mineral Engineering Student Enrolment in the United States," read at the A. I. M. E. meeting on Feb. 16. 1931, are given for comparison. Acknowledgment is made to all the administrative officers of the institutions who took the time from their busy lives to supply the in- formation asked for. Their fine cooperation has alone made possible these two surveys with a completeness of detail never before attempted

Jan 1, 1934

By P. B. Liebermann

THE resistance to motion offered by mine cars is caused principally by: Rolling friction, flange friction, bending rails, bearing friction and wind resistance. With proper construction and with a fair amount of attention and care, that is, under favorable conditions, the first three items cannot be greatly improved. The wind resistance ordinarily is negligible on account of the slow speeds commonly used. The bearing friction, however, is a variable item, depending upon the design, the bearing material, the lubrication, the location (whether in wheel-hub or on car-body) and the alignment. Under the most favorable conditions the bearing friction will reach a lowest possible value. By the development of a successful anti-friction mine-car bearing this lowest value has been improved to such an extent as to affect the whole system of mine haulage. After being satisfied of their durability and certainty of operation, any investigation into the advantages of anti-friction bearings for mine cars will have to be based upon reliable information as to the saving in power of such bearings. While numerous tests have been made in this direction, the results have not always been convincing, principally because of the rather crude methods that were employed. These crude methods are the main cause of the wide variations existing in regard to the exact amount of the frictional resistance. Frequently an ordinary spring balance is used and the pull necessary to move a certain car or train of cars is obtained by a number of readings. Such spring balances necessarily have a coarse graduation and the continuous vibration and fluctuations to which they are subjected make them highly dependent upon the individual observer. Further, they must be frequently calibrated. Sometimes these tests were made without regard to acceleration, speed or even grade.

Jan 6, 1916

By J. J. Gilman

WHEN a cleavage crack that is moving through a crystal intersects a screw dislocation, a jog is created in the crack front. As the crack continues to move, the jog leaves behind a cleavage step. This mechanism was proposed by Amelinckx and Votava,' Pratt, bnd Gilmanh t about the same time. At that time the evidence for the mechanism was largely indirect. Other evidence has been presented by Low, Bilby and Smith,5 and Forty.' It is the purpose of this paper to present more direct evidence of this mechanism and to show that observations of cleavage steps can be used to detect screw dislocations. Experimental Lithium-fluoride crystals that were purchased from the Harshaw Chemical Company, as well as natural mineral crystals and metal crystals, were used in the experiments. Although cleavage steps can be observed on transparent crystals with a metallurgical microscope, the contrast is poor. Marked improvement in the contrast is obtained by depositing thin (1000A) films of silver or aluminum onto the surfaces. The contrast also can be improved by using a phase-contrast microscope, but the simpler silvering method gives just as good results. Tolansky interferometric microscopy, and electron microscopy were used to measure the heights of cleavage steps. The etching techniques developed by Gilman and Johnstonh ere used to detect dislocations in the LiF crystals. Results The dislocations that create cleavage steps can originate in three ways: a) They can be grown into crystals b) They can be introduced by plastic deformation prior to cleavage c) They can be formed just in front of the tip of a propagating cleavage crack.' These three situations will be considered in turn. Grown-in Dislocations—It is not possible to see the individual monomolecular cleavage steps that emanate from isolated screw dislocations in crystals.

Jan 1, 1959

By Richard Ely

Conservation Means Preservation, Improvement, Justice CONSERVATION, narrowly and strictly considered, means the preservation in unimpaired efficiency of the resources of the earth; or in a condition so nearly unimpaired as the nature of the case, or wise exhaustion, admits. And broadly considered, it means more than the word itself implies, for it naturally includes an examination of methods whereby the natural inheritance of the human race. may he improved; and still more broadly considered-and as used in popular discussion-it includes a treatment of the effects of productive conservation measures upon distribution. We shall give our attention briefly to the main points in this informal definition before we pass on to the thesis that conservation is largely a matter of property relations-that a wise conservation policy means wise property relations. Preservation of Natural Resources First, conservation suggests simply preservation, and, in the treatment of the subject which we have had in the United States, emphasis has been laid upon the past and present waste of natural resources and upon the means of putting a stop to this waste. The forests have been depleted; soil has been washed by rapidly flowing surface water from mountain sides. These rapidly flowing waters have produced high streams and devastating inundations, followed by low streams and impeded navigation. The forests have, moreover, been so removed as to bring great danger of fire, and destructive conflagrations have resulted in large waste of resources, including in some cases a destruction of the humus, supplying essential elements in the fertile soil. As a remedy we must have measures to reforest mountain sides, and this means large social control, very frequently taking the form of public ownership and management; but in addition we always find actual and proposed

Jan 2, 1916

By J. E. Clennell

It is a common observation that the improvements introduced in practice since the first announcement of the cyanide process have been almost entirely mechanical. Although .a good deal of study land research has been devoted to the chemical problems [involved, the results obtained appear trifling in comparison. Few of the suggested modifications in the chemical treatment have come into practical use and those only in limited fields. Nevertheless, if we study the recent history of the cyanogen compounds from a somewhat broader standpoint, we shall find that considerable additions have been made, not only to our knowledge of their chemical properties, but also to their applications for industrial purposes. The present review of these advances naturally falls into two divisions: (1) processes involved in the treatment of ores; (2) manufacture of cyanides and other related compounds. Part I. Advances in the Chemistry of Ore Treatment by Cyanide In the attempt to extend the scope of the process, various ores have been encountered which contain gold and silver in such forms that they will not yield satisfactorily to ordinary methods of cyanide treatment. In some cases the difficulty is due to the excessive action on the solution of base metals present in the ore; in others, to the occurrence of minerals such as dyscrasite (the native alloy of antimony and silver), or a supposed oxidized manganese compound containing silver, which are either altogether insoluble in or very slightly attacked by cyanide. A particularly troublesome case is that of the so-called "graphitic" ores, containing carbon in some form which has the property of precipitating gold and silver already dissolved. Other efforts have been directed to improving extraction by electrolysis of working solutions, and by addition of various chemicals with or without electrolysis; to the diminution of cyanide consumption by "re-

Jan 1, 1916

By Albert G. Zima

ACCORDING to recently published statistics, it is predicted that as much oil must be produced during the next 16 years as has been produced during the past 75, in order to satisfy the high rate of consumption of petroleum products. During 1934, over 17,000 oil wells were completed in the United States, and it is expected that over 20,000 additional wells will be drilled during the current year. Were it not for the remarkable progress made during recent years in the improvement of drilling technique and in the development of equipment used in the production phase of the oil industry, it is doubtful whether sufficient oil could be produced to meet present requirements. A few years ago, wells seldom were deeper than 3500 to 4000 ft., owing to the limitations of the drilling methods and equipment employed.. Today, 'however, through the application of scientific drilling methods and the adaptation of modern equipment and improved materials, many wells range from 6000 to 8000 ft. in depth, and a few recent completions exceed 10,000 feet. DRILL TOOLS Modern rotary drilling tools are the product of ingenious design and careful selection and adaptation of materials used in their construction. They must withstand terrific abrasion and, because of their compactness, must be designed to resist exceedingly high unit stresses. In bits, core drills and reamers, the bodies are made of either forged or cast alloy steels, heat-treated to develop a combination of high strength and toughness. To provide sufficient strength to the threaded portions and to protect the threads from distortion or damage, the box or pin sections of the tools are hardened to approximately 310 to 330 Brinell hardness

Jan 1, 1935

By Albert G. Zima

According to recently puhlished statistics, it is predicted that as much oil must be produced during the next 16 years as has been produced during the past 75, in order to satisfy the high rate of consumption of petroleum products. During 1934, over 17,000 oil wells were completed in the United States, and it is expected that over 20,000 additional wells will be drilled during the current year. Were it not for the remarkable progress made during recent years in the improvement of drilling technique and in the development of equipment used in the production phase of the oil industry, it is doubtful whether sufficient oil could be produced to meet present requirements. A few years ago, wells seldom were deeper than 3500 to 4000 ft., owing to the limitations of the drilling methods and equipment employed. Today, however, through the application of scientific drilling methods and the adaptation of modern equipment and improved materials, many wells range from 6000 to 8000 ft. in depth, and a few recent completions exceed 10,000 feet. Drill Tools Modern rotary drilling tools are the product of ingenious design and careful selection and adaptation of materials used in their construction. They must withstand terrific abrasion and, because of their compactness, must be designed to resist exceedingly high unit stresses. In bits, core drills and reamers, the bodies are made of either forged or cast alloy steels, heat-treated to develop a combination of high strength and toughness. To provide sufficient strength to the threaded portions and to protect the threads from distortion or damage, the box or pin sections of the tools are hardened to approximately 310 to 330 Brine11 hardness number. Drill and reamer cutters are generally of the movable type; i.e., serrated cones, cylinders or disks, which can readily be replaced when

Jan 1, 1935

By Albert G. Zima

According to recently puhlished statistics, it is predicted that as much oil must be produced during the next 16 years as has been produced during the past 75, in order to satisfy the high rate of consumption of petroleum products. During 1934, over 17,000 oil wells were completed in the United States, and it is expected that over 20,000 additional wells will be drilled during the current year. Were it not for the remarkable progress made during recent years in the improvement of drilling technique and in the development of equipment used in the production phase of the oil industry, it is doubtful whether sufficient oil could be produced to meet present requirements. A few years ago, wells seldom were deeper than 3500 to 4000 ft., owing to the limitations of the drilling methods and equipment employed. Today, however, through the application of scientific drilling methods and the adaptation of modern equipment and improved materials, many wells range from 6000 to 8000 ft. in depth, and a few recent completions exceed 10,000 feet. Drill Tools Modern rotary drilling tools are the product of ingenious design and careful selection and adaptation of materials used in their construction. They must withstand terrific abrasion and, because of their compactness, must be designed to resist exceedingly high unit stresses. In bits, core drills and reamers, the bodies are made of either forged or cast alloy steels, heat-treated to develop a combination of high strength and toughness. To provide sufficient strength to the threaded portions and to protect the threads from distortion or damage, the box or pin sections of the tools are hardened to approximately 310 to 330 Brine11 hardness number. Drill and reamer cutters are generally of the movable type; i.e., serrated cones, cylinders or disks, which can readily be replaced when

Jan 1, 1935

By Franklin G. Pardee

IN 1920 the Minnesota Tax Commission estimated a reserve of 1,341,674,538 long tons of iron ore in Minnesota, the Michigan State Tax Commission report showed 199,092,855 long tons in reserve in that state, and the Wisconsin Geological Survey set the Wisconsin reserves at 21,500,000 long tons. The total reserve that year for the Lake Superior District amounted to 1,562,267,393 long tons. Ten years later the reserves of iron ore in these same districts were Minnesota 1,235,227,510, Michigan 168,349,823, and Wisconsin 23,000,000, or a total of 1,426,577,333 long tons. The decrease in ore reserves in this ten-year period was 135,690,060 long tons, but the shipments were 520,746,975 long tons. In other words, the ten-year depletion in reserves was only 8.68 per cent. If similar conditions carry into the future this calculation would indicate a life for the ore reserves of the Lake Superior region of over 100 years.

Jan 1, 1933

By J. M. McDowell, E. C. Doty, F. Morgan

Improvements in the X-ray method of measuring liquid saturation and saturation distribution are presented. Two identical direct current amplifiers have been added to measure continuously the intensities of the X-ray tube output and the beam which has passed through the core under test. The ratio of these intensities is automatically recorded on a modified Brown Electronik Recorder. Arrangements have been made to drive the core automatically and in synchronism with the recorder chart so as to give a continuous curve showing the variation of liquid saturation along the length of the core. By determining the ratio of the two X-ray beam intensities simultaneously the measurements are made essentially independent of small fluctuation in voltage and current supplied to the tube. This improved technique has been used for investigating the fluid distribution along the length of cores and core assemblies when one fluid is displaced by another. Typical results of these studies are shown. INTRODUCTION In a previous publication' a method was described for measuring the oil saturation in cores which was based on the absorption of X-rays by the fluid content of the core. While that technique is capable of yielding accurate results, the original apparatus was not especially convenient for determining the fluid distribution along the length of a core. This was primarily due to the slow response of the amplifier and galvanometer and the necessity of making a point by point survey of the material under investigation. It was, therefore, not only possible for sections of the core having a variable or unusual saturation distribution to escape observation entirely, but changes in output of the X-ray generator between readings on the unknown and the monitor introduced errors in the measurements that could be avoided only by further stabilization of the source or by taking a large number of readings. This paper describes a method and apparatus for recording continuously and automatically the intensity of the X-ray beam that is transmitted by a core. The variation of saturation with time at a given section of the core may thus be found, or by scanning the core by driving it in synchronism with the recorder the saturation distribution may readily be determined. As indicated in the previous paper, the X-ray method possesses an advantage over the weighing technique in relative permeability experimentation in that the core need not be removed from the holder for the purpose of making a saturation measurement. Furthermore, the actual distribution of fluid and the effects upon that distribution of inflow and outflow heads may be investigated. And errors due to gas bubbles or loss of liquid that are frequently sources of error in volumetric methods of saturation determination are avoided. PRINCIPLE OF THE METHOD The energy in an X-ray beam that has passed through an absorbing material is expressed by the well known formula: E = E0, e-cd (1) where E, is the energy in the incident beam, µ the mass absorption coefficient, c the density or concentration of absorbing material, and d is the length of path of the beam in the absorber. The coefficient µ varies with the wavelength of the radiation as well as with the absorbing material. The output of an X-ray tube varies in an approximately linear manner with the tube current, but to the second or higher power of the anode voltage. Moreover, the quality or wavelength distribution of the radiation varies with the voltage.

Jan 1, 1950

By E. J. Eisenach, Edward Matsen

AT the present time the Climax Molybdenum Co. is the largest molybdenum producer in the world and the operator of the largest underground mine in North America. It has grown steadily and rapidly since its beginning in 1917. Only 250,000 lb of MoS2 were produced during the first year from 1917 to 1918 when the company was formed. Operations were suspended shortly thereafter because of the lack of a market and knowledge of the uses of molybdenum. During World War I it was used as a substitute for some rare metals and for minor chemical purposes. After 5 years of intensive research and sales promotion, Climax metallurgists succeeded in finding proper applications for the newly discovered metal and the mine was reopened in 1924. Demand for molybdenum increased gradually and in 1930, 3.5 million lb of MoS2 were produced. In the meantime, research work for additional uses of molybdenum continued until it had established itself as one of the most important alloying elements in producing high quality steels. After the start of World War 11, from January 1942 to October 1953, 43 million tons of molybdenum ore were mined and 484 million lb of MoS2 were produced. Climax mine is located in Colorado, 100 miles southwest of Denver and 12 miles northeast of Leadville on the Continental Divide of the Rocky Mountains. The principal mine workings range from 11,170 to 12,000 ft in elevation. Topographically, it lies in the base of a large cirque that is surrounded by Mt. Bartlett to the north, Clinton Peak and McNamee Peak to the east and Ceresco Ridge to the south. This cirque opens to the west and to the Ten Mile Valley.

Jan 3, 1954

By CLAYTON C. BALL

In the year 1948, more than ever before, the coal industry established itself on the threshold of a new and exciting future expansion. While production did not equal the wartime and peacetime peaks of 1944 and 1947, it was, in review, a good coal year. During the latter part of the year a combination of mild weather, record stock piling, and general business slackening reduced coal demand to the extent that marginal mines suspended operations, while mines remaining active found it necessary to renew their attention to producing better products at lower operating costs.

Jan 1, 1949

By D. Harrington

ANNUAL or necessary inspections and investigations of coal mines for various purposes were made possible through the Federal Coal Mine Inspection Act of May 7, 1941, which authorized entry to the Secretary of the Interior through the Bureau of Mines. Primary object of these inspections is to obtain information pertaining to health and safety conditions. Among the purposes for which the data are to be used, are annual reports to Congress, the publication of inspection reports, and the compilation and publication of statistics. The act states that inspections and investigations shall be made by employees of the Bureau of Mines, who shall co-operate with other bureaus of the U. S. Department of the Interior, as well as with the official mine-inspection, safety cr health agencies of the several states and territories. The act specifies that a coal-mine inspector shall have "the basic qualifica-

Jan 1, 1946

By A. L. Engel

IN the treatment of complex ores by flotation, one of the most important steps is conditioning the feed. Conditioning primarily consists of the addition, in the grinding circuit, of an alkaline reagent, for example sodium carbonate, which neutralizes any acidity of ore and mill water, counteracts the effect of 'harmful soluble salts, disperses colloids, and provides the necessary alkalinity for the best metallurgical results. The several minerals of the ore should be put in such condition that they may be floated or rejected as desired, through the action of further reagents thereafter used.

Jan 1, 1932

By H. Rush Spedden, Arvid Thunaes

Pilot plant test work in 1942 and 1943 showed that by a combination of desliming, fine-size classification, and Sullivan deck concentration it is possible to recover heavy minerals such as cassiterite at least as fine as 10 microns in size. This appreciable improvement in gravity concentration practice has been substantiated by several full-sized plants.

Jan 8, 1950

By E. M. Wise

WHEN man became dissatisfied with the mere utilization of physical force and began to use weapons, he made a definite stride forward. At first he used sticks, animal bones and stones, often rudely shaped to some particularly lethal form. These devices, while crude, were moderately effective. How- ever, some of the brighter men of the tribe found that certain particularly heavy "stones" were somewhat ductile and could be hammered into more effective weapons than those previously known. Later, probably through the misuse of one of these weapons to stir the campfire, it was found that heating softened and perhaps actually melted the material. The process of annealing had been discovered! Smelting the more easily reducible metals was in all probability one of those fortuitous accidents which was followed up by thoughtful researchers who ultimately developed the technique of mixing various ores to produce bronze and even some of the nickel content alloys. The resulting products were at first lumps of more or less ductile material which could be hammered to shape, and were thus incidentally hardened by this process. The hardening of metals by alloying and cold working remained for many centuries the only known methods for improving their properties.

Jan 1, 1931

By AIME AIME

COMMITTEE No. 2 of the Iron and Steel Institute b f Great. Britain has presented its first report, of 27 printed pages, on blast-furnace plant and practice. This report outlines the various features of modern blast-furnace practice with brief comments thereon, and with references to some of the more recent methods devised for applying the principles and attaining the purposes aimed at' under these headings.. In general, the trend in the United States is in the direction of larger and larger furnaces with ever increasing capacity from which, with improved details in methods and equipment, and attention to details of management, considerable progress in. economy of production has been attained, in fuel consumption and in other items of production cost.

Jan 1, 1929

By William D. Klopp, Joseph R. Stephens

A substantial reduction in the 300°F ductile-to-brittle transition temperature for unalloyed chromium was achieved in alloys from systems which resemble the Cr-Re system. These alloy systems include Cr-Ru, Cr-Co, and Cr-Fe. Transition temperatures ranged from -300° F for Cr-35 at. pct Re to -75°F for 0-50 at. pct Fe. The ductile alloys have high grain gvowth rates at elevated temperatures. Also, Cr-24 at. pct Ru exhibited enhanced tensile ductility at elevated temperatures, characteristic of superplas-ticity. It is concluded that phase relations play an importarlt role in the rhenium ductilizing effect. The ductile alloys have compositions near the solubility limit in systems with a high terminal solubility and which contain an intermediate o phase. The importance of enhanced high-temperature ductility to the rhenium ductilizing effect is not well understood although both may have common basic features. CHROMIUM alloys are currently being investigated for advanced air-breathing engine applications, primarily as turbine buckets and/or stator vanes. The inherent advantages of chromium as a high-temperature structural material are well-known1 and include its high melting point relative to superalloys, moderately high modulus of elasticity, low density, good thermal shock resistance, and superior oxidation resistance as compared to the other refractory metals. Additionally, it is capable of being strengthened by conventional alloying techniques. The major disadvantage of chromium is its poor ductility at ambient temperatures, a problem which it shares with the other two Group VI-A metals, molybdenum and tungsten. For chromium, the problem is further amplified by its susceptibility to nitrogen em-brittlement during high-temperature air exposure. In cases of severe nitrogen embrittlement, the ductile-to-brittle transition temperature might exceed the steady-state operating temperature of the component. The low ductility of chromium would make stator vanes and turbine buckets prone to foreign object damage. The present work was directed towards improvement of the ductility of chromium through alloying, with the anticipation that any improvements so obtained might be additive to strengthening improvements achieved through different types of alloying. The alloying additions for ductility were selected on the basis of the similarity of their phase relations with chromium to that of Cr-Re. The reduction in the ductile-to-brittle transition temperatures of the Group VI-A metals as a result of alloying with 25 to 35 pct Re is well established.a4 the temperature range -300" to 750° F. This phenomenon is commonly referred to as the &apos;<rhenium ductilizing effect"; this term is also used to describe systems in which the ductilizing element is not rhenium. Other alloy systems which have recently been shown to exhibit the rhenium ductilizing effect include Cr-Co and c-Ru.= In order to explore the generality of this effect, alloys were selected from systems having phase relations similar to that of Cr-Re, primarily a high solubility in chromium and an intermediate o phase. The following compositions were prepared: Cr-35 and -40Re; Cr-10, -15, -18, -21, -24, and -27 pct Ru; Cr-25 and -30 pct Co; Cr-30, -40, and -50 pct Fe; Cr-45, -55, and -65 pct Mn. Seven other systems were also studied which partially resemble Cr-Re. These systems have extensive chromium solid solutions or a complex intermediate phase, not necessarily o. The compositions evaluated include the following: Cr-20 pct Ti; Cr-15, -30, and -45 pct V; Cr-2.5 pct Cb; Cr-2.5 pct Ta; Cr-20 pct Ni; Cr-6, -9, -12, and -15 pct 0s; Cr-10 pct Ir. The compositions of alloys in these systems were chosen near the solubility limit for the chromium-base solid solutions, since in the Group VI-A Re systems, the saturated alloys are the most ductile. These alloys were evaluated on the basis of hardness, fabricability, and ductile-to-brittle transition temperatures. In addition to the studies of alloying effects on ductility, an exploratory investigation was conducted on mechanical properties at high temperatures in Cr-Ru alloys EXPERIMENTAL PROCEDURE High-purity chromium prepared by the iodide deposition process was employed for all studies. An analysis of this chromium is given in Table I. Alloying elements were obtained in the following forms: Commercially pure powder — iridium, osmium, rhenium, and ruthenium. Arc-melted ingot — titanium and vanadium. Electrolytic flake — iron, manganese, and nickel. Sheet rolled from electron-bearn-melted ingot — columbium and tantalum. Electron-beam-melted ingot — cobalt. Sheet rolled from arc-melted ingot — rhenium. All alloys were initially consolidated by triple arc melting into 60-g button ingots on a water-cooled hearth using a nonconsumable tungsten electrode. The melting atmosphere was Ti-gettered Ar at a pressure of 20 torr. The ingots were drop cast into rectangular slabs and fabricated by heating at 1470" to 2800° F in argon followed by rolling in air. Bend specimens measuring 0.3 by 0.9 in. were cut from the 0.035-in. sheet parallel to the rolling direction. The specimens were annealed for 1 hr in argon, furnace cooled or water quenched, and electropolished prior to testing. Three-point loading bend tests were conducted at a crosshead speed of l-in. per min over

Jan 1, 1969

By G. E. Keller

In connection with the work of Committee D5, Coal and Coke, of the American Society for Testing and Materials in developing new standards and improving old standards, series of tests were made to check the variance of sample preparation and analysis of American coals. Table I in the "Tentative Method of Preparing Coal Samples for Analysis - 02013-62T" is rather complicated, and the tests were designed to develop data for the simplification of this table. An allowance of 20% of the total variance of sampling and analysis for the sample preparation and analysis steps was used. Also, instead of coals being grouped into ash ranges, they were grouped as washed and raw (unwashed) coals. As a result of these tests, a simplified Table I for Tentative Standard 02013 has been proposed. A standard test for laboratories to check their variance of sample preparation and analysis has been developed. Committee D5 on Coal and Coke of the American Society for Testing and Materials has been making a study of all standards applying to coal for the purpose of improving and bringing them up to date and for breaking some of the existing standards covering a number of tests into single standards. As an illustration, sample preparation is now partly covered in ASTM Designation D492-48, Sampling Coals Classified According to Ash Content, and partly in ASTM Designation D271-58, Laboratory Sampling and Analysis of Coal and Coke. The latter contains, in addition to parts of sample preparation, methods for determining Moisture, Ash, Volatile Matter, etc. Although revision of sampling methods and sample preparation methods are now assigned separately, it is possible that they may end up as one standard. One of the first new Tentative Standards developed as the result of these studies was ASTM Designation D2013, Tentative Method of Preparing Coal Samples for Analysis. Although this method is quite an im- provement over that in the old standards and gives very specific instructions, Table I (attached) is quite complicated and rather hard to understand. In order to take advantage of reduced quantities or weights, it is necessary to know the ash content within rather narrow limits before sample preparation and no distinction is made as to whether the coal is cleaned or uncleaned. No limits of accuracy are assigned to the sample preparation and analysis. The total over-all accuracy of sampling, preparation and ash determination as given in D492-48 has been specified for commercial sampling procedure as follows: "This procedure is intended for an accuracy such that if a large number of samples were taken from a single lot of coal, the test results in 95 out of 100 cases would fall within ? 10 per cent of the average ash content of the sample." Although Appendix 11, Method for Determining the Over-All Variance of Reduction and Analysis in the Tentative Methods for Mechanical Sampling of Coal, ASTM Designation D2234-63T, does give a method for determing the over-all accuracy of preparation and analysis expressed as variance and also the F test, it does not permit the determination of the variance at the various stages of reduction or of the ash determination. It was decided in 1961 to ask a number of laboratories to run a series of tests for the purpose of determining the variance at various stages of reduction and analysis with the view of simplifying Table I of the Tentative Standard D2013-62-T. This paper is a record of this series of tests with recommendations which resulted from the tests. At the same time and preceding these tests the International Organization for Standardization under Committee TC/27 WG 7 was studying the same problem. Tomlinson1 of England and Dr. paul2 of West Germany had made studies giving quite a bit of information. Also Schwerd and coryel13 published some information which was the main basis for the Mechanical Division provision in ASTM Tentative Standard D2013-62T, Table I. In checking with the various laboratories which offered to cooperate in these tests, none was found which used mechanical division through the entire preparation procedure. It was then decided to use riffles at all stages with the thought that if riffles gave satisfactory variances, approved mechanical

Jan 1, 1965