Search Documents

By S. G. Valentine

BLAST-FURNACE blowing engines are broadly of two main types: either steam- or gas-driven reciprocating engines, or turbine-driven rotary engines. Some results of experience with a furnace blown by an engine of the latter type may be of sufficient general interest to relate. The first engine of this type was installed at Oxford Furnace, New Jersey, before the writer's connection with this plant, in March, 1910. This furnace uses chiefly New Jersey magnetites and had been in blast seven months on its old engines when the turbo blower was started. It was 80 ft. high by 17 ft. 6 in. bosh and 11 ft. hearth diameter. It is of interest to see from the records what happened when the turbo engine was put to work. But of course, as the old blowing equipment was rather antiquated, consisting of two I. P. Morris engines with air cylinders 72 by 72 in., in good running order, however, it is evident that the comparison between their work and that of the turbo blower cannot be interpreted as being between machines that were respectively of equal excellence as representatives of their types. Still the results were gratifying and -interesting. The records show that, with the old engines blowing 13,630 cu. ft: of air per minute, measured by piston displacement, the furnace was working up about 480 tons of stock per 24 hr. and producing an average of 132 tons per day and a maximum of 166 tons. The rotary blowing engine installed was a General Electric Co. machine, the driving end being a Curtis steam turbine and the air end a six-stage rotary compressor, all running at about 1,500 to 1,600 rev. per minute, and having a capacity of 25,000 cu. ft. of air per minute up to 25 lb. pressure, and equipped with an automatic constant-volume variable-speed governor. After running this blower, for a period equal to that covered above by the old engines, at an average rate of 15,000 cu. ft. of air per minute, the furnace worked up an average of about 592 tons of material and produced an average of 170 tons per day. Thus, on an apparent increase of 10 per cent. in the air volume there was an increase of about 23.5 per cent. in the materials worked up and of about 28.8 per cent. in the product. For the first calendar month's operation of the turbo blower, on an average of 15,040 cu. ft of air per minute, there is

Jan 2, 1914

By Clarence Zener

IT has long been known that the density of a metal usually decreases with cold-work. Thus O'Neill1 observed as early as 1861 that cold hammering of commercial hot-rolled copper is accompanied by a decrease of density of 0.2 per cent, and that subsequent annealing restores the original density. The origin of this density change, however, has remained obscure. In particular, experiment has not yet decided whether it is due to the presence of small cavities and an increase in intergranular surface or to an actual expansion of the lattice itself. This uncertainty in the origin of the change in density is a reflection of our uncertainty as to the changes induced in a metal by cold-working. One school regards cold-working as a breaking up of the original grains into a large number of perfect crystallites somewhat randomly orientated with respect to one another.2 According to this viewpoint, the mere introduction of a large intercrystallite surface induces a net volume expansion. Another school regards cold-working primarily as a distortion of the grains. It is not obvious that this second viewpoint will lead to a net volume expansion. The purpose of the present paper is to show that this is indeed the case, and that this expansion is of the right order of magnitude to explain existing experimental data. The physical basis for the association of an expansion with distortion lies essentially in the variation of the elastic moduli with volume. This variation is considerable. Thus from Table I we see that a I per cent increase in volume for the case of copper will decrease the bulk modulus K by 10 per cent, the shearing modulus µ by 3.8 per cent. If we thus twist a rod through a given angle, we shall do less work upon it if it increases slightly in volume, thereby reducing the torsion modulus that involves as a factor the shearing modulus. A general principle' in physics states that the rod will so adjust itself as to have a minimum potential energy consistent with the end restraints. It will therefore expand. [ ] In order to obtain a quantitative comparison with experiment, we follow Maier4 in comparing the lattice expansion with the latent energy of cold-work. This latent energy has been measured directly by Taylor and Quinney5 on copper rods subjected to torsion, and may amount to as much as 15 per cent of the total work done upon the specimens. We shall assume that this

Jan 1, 1941

By James Norman, O. C. Ralston, John Dasher

Most mineral products are used in the finely divided state, but some are sold in larger sizes. Coal, gravel, metallurgical fluorspar, phosphate rock, hematite, chro-mite, and other products are sold in sizes coarser than can be treated by many mineral-dressing methods. Gravity separation of coarser sizes by log washing and jigging is probably as ancient as any process now in use. The performance of jigs on a feed with sufficient difference in density of the minerals is excellent, but many families of minerals are too similar in density to be separated effectively by this method. The use of heavy suspensions of fine solids to separate coarse coal from bone and slate has been in use for some years. This separation by sink-and-float was limited until recently to light minerals. Development of galena and ferrosilicon as suspension media, by Minerals Beneficia-tion, Inc., at Mascot, Tenn., Pitcher, Okla., and Crosby, Minn., under patents granted during and since 1938, has permitted excellent results to be obtained on minerals of very similar densities up to 3.3. This process has been put In the hands of American Cyanamid Co. for exploitation, and further research now in progress may increase the density of suspension obtainable so that separations at a density of 4.0 may be practicable before this is published. The Huntington-Heberlein dense-medium process, developed in England, is also being commercialized in the United States by Sink and Float Corporation. Du Pont has developed a sink-and-float separation using halogenated hydrocarbons as parting liquids; at this writing, the method is used commercially only on coal but has been successful in the pilot plant on many other minerals using tetrabrom-ethane at densities up to 2.95. While these processes were being developed to extend the range of separation by difference in density to the coarser sizes, the Bureau of Mines was engaged in developing a process that will extend the range of separation by difference in wettability up to 2-in. size. War work has pushed aside its further development indefinitely. The results are published here with the hope that some use may be suggested that will justify post-war development, and so that readers that may be able to make immediate use of the scheme may have the information. Earlier Work It has been known since the time of Herodotus (B.C. 484(?)-425) that water-repellent particles will adhere to sticky surfaces. That early historian reports the recovery of gold from the mud of a lake

Jan 1, 1943

Discussion of the paper of G. Howell Clevenger and Bhupendranath Ray, presented at the New York Meeting, October, 1913, and printed in Bulletin No. 82, October, 1913, pp. 2437 to 2475. ALLERTON S. CUSHMAN,* Washington, D. C.:-I am very much interested in the subject matter of this paper. I have had occasion to speak to this question before. There has recently been so much written and said and claimed about the effect produced by the addition of small quantities of copper to steel that there is certainly an impression abroad that a new and wonderful cure-all has been discovered. Are we facing a method of alchemy by which, at the expenditure of very little trouble and only a few cents' worth of copper per ton, the well-known characteristics of steel with respect to some features are so marvelously changed as in effect to produce a new metal ? I am a great believer in the future of the iron and steel alloy field. I do not think that with all the advances we have made in metallurgy we have begun to scratch the possibilities of usefulness to mankind in the exploration of the alloy field, and I include in that alloy field even what might be designated as the dilute alloy field; that is to say, where a very small quantity of a metal alloyed with iron and steel confers upon it some new or extraordinary qualities. With respect to many of the physical characteristics of the copper-iron or copper-steel alloys I am not particularly competent to speak. With respect, however, to the investigation of corrosion problems and with respect to claims made with regard to resistance to corrosion, I am competent to speak insofar as I have specialized to some extent in that field and have given up a great deal of my time for a great many years to a study of it. Some years ago, being particularly interested in the study of corrosion problems, I received the very generous permission of a large manufacturing concern to use their large open-hearth furnaces any way I saw fit for exploring this particular field. There is not a metallurgist in this room who will not realize the generosity of a manufacturing company who would permit a man to pursue a theory and give him as his material to work with 60 tons of molten metal. At all events, I threw copper into the open-hearth furnace. I explored this alloy field, not in a ittle crucible in which I had to take out portions and have them

Jan 12, 1913

By Robert Anderson Cook

AS the margin of profit in the manufacture of iron continues to decrease, attention is called more and more to economies in every department. Beginning at the bottom, in the preparation of the ore at the mine, me notice a general tendency is towards the shipment of richer ores, securing to the mine-owner a better price per ton, which the purchaser is glad to pay by reason of the saving in freight of iron, and in the cost of reduction, which depends so largely upon the amount of fuel and flux, and the productive capacity of the plant. In other words, the difference in value between rich and poor ores is much greater than their relative percentages of iron indicates; because the barren material in a lean ore is not merely worthless, it is a positive source of expense, requiring transportation, handling, fluxing, smelting, and its due share of general expenses; in return for which it yields nothing and decreases the available capacity of a given plant and capital for profitable work. The enriching of the ore is done in most places by hand-picking, and in a few by wet concentration; but the managers of several magnetite mines in Sweden have been practically successful in doing it by machinery. The only magnetic separating machine which has actually taken the place of hand-picking was designed and patented by Mr. Jonas Wenström of Örebrö, Sweden. In this machine, which is illustrated in Figs. 1 and 2, Mr. Wenström has taken advantage of the property of soft iron to become magnetized by induction. The machine consists of a barrel made up of soft iron bars and some non-conducting material (usually wood), which is rotated around a stationary shaft by means of a cog-wheel. Inside of this barrel, on the shaft, is placed eccentrically a cylindrical electro-magnet, provided with a number of manges (N, S, Fig. I), between which wire is wound in such a manner that the flanges are of negative and positive polarity, being energized by a current passing through the wire coils from a small dynamo. As will be seen in Fig. 1, the flanges, N, S, are circular, and follow the internal contour of the barrel on the front side, while on the opposite side they are cut down to the line B, B' in Fig. 2. Hence the bars of the revolving barrel on the front side of the machine are mag-

Jan 1, 1889

By John Guillermo Bartram

The oil industry continued relatively quiet in Wyoming in 1935, although production increased about 8 per cent over the previous year; 55 oil wells were completed in 1935, compared to 34 in 1934, and at the end of the year 44 wells were drilling, 33 in proven fields and 11 in wildcat locations. The total drilling a year ago was only 30. In the year 1935 Wyoming produced a total of 13,451,000 bbl. of oil, a gain of 912,000 bbl. over the 1934 figure of 12,539,000 bbl. Approxi-mately two-thirds of the increase, or 630,000 bbl., was from black oil fields and one-third, or 285,000 bbl., from light oil pools. Salt Creek, with production of 6,357,000 bbl., is still many times the largest field in Wyoming but in 1935 it made less than 50 per cent of the state's total, after producing more than all other fields in the state for 24 years; however, its decline was only 3.8 per cent from the previous year. Oregon Basin, a black oil field, held second place again with production of 1,163,-000 bbl., a good increase over 1934. Grass Creek, with increases in both its light and black oil, jumped into third place; and Lance Creek, with its new Sundance light oil production, was in fourth place in the amount of production. Frannie, which was in third place in 1934, dropped far back on the list because of lack of market. Byron and Garland, two other black oil fields in the Big Horn Basin, increased considerably. Big Muddy, a prominent light-oil field, was down with a natural decline; and Elk Basin, also light oil, produced less because of market conditions. During 1934 only three gas wells were drilled in Wyoming and 29 dry holes, 13 in proven fields and 16 at wildcat locations. Of the latter, 5 were on wildcat structures of considerable interest. Of the 55 wells completed during the year, 53 were in proven fields and of these 17 were small ones in the shallow Osage field and 10 were light-oil wells good for 1500 to 3000 bbl. each in the Lance Creek field. Discoveries Two of the oil wells were discoveries at Medicine Bow and Sheep Creek. Medicine Bow is a very large anticline with more than 3500 ft. of closure and is located in Carbon County in the south-central part of the state. In 1923 it showed some oil in the Upper Cretaceous Frontier

Jan 1, 1936

By C.P. Clingerman

The recent iastallation of a combination dust catcher, gas washer and precipitator at Carrie blast furnaces of the Homestead Steel Works has given very satisfactory results. The following description of the gas-cleaning installation is based on actual operating experience. When Carrie blast furnace No. 3 was rebuilt the decision was made to fine-clean all the gas produced by the furnace, because the management wanted fine-cleaned gas for fuel in the stoves and boilers. In order to keep the installation cost as low as possible, the gas-cleaning system was streamlined. All by-pass lines and goggle valves for bypass lines were eliminated from the system. A radical departure from the use of 8-in. tubes in the Cottrell-type precipitators was made by using 12-in. diameter tubes in a single compartment, the single compartment being divided into two units by a single partition wall in the top header. The Furnace Proper A few of the characteristic points and dimensions of the furnace proper are: Hearth diameter.............. 26 ft. o in. Bosh diameter............... 29 ft. 1 3/4 in. Stock-line diameter........... 20 ft. o in. Large-bell diameter........... 14 ft. 8 in. Small-bell diameter........... 6 ft. 6 in. Height of furnace from center of iron notch to bottom of large bell, closed............ 94 ft. 4 in. Height of furnace from center of iron notch to main platform ...................... 105 ft. o in. The furnace top is equipped with a MC-Kee revolving distributor, the operation of which is electrically interlocked with the skips, bell hoists, and coke-weighing and charging apparatus through a Freyn automatic charging control. The gas leaves the furnace first through four offtakes, 5 ft. 9 in. in diameter, then through uptakes that, are approximately 85 ft. high, which feed into a single down-comer that is 9 ft. in diameter. Dust Catcher The primary dust catcher installed (Fig. I) may be described as a single-cone type. The inlet pipe at the top of the dust catchei is 9 ft. in diameter; it is flared to a conical shape as it extends down inside the dust-catcher shell, which is 35 ft. in diameter, 37 ft. high on the straight side, and has a conical top and bottom. The slope of the bottom is so0 with the horizontal. The cone-shaped pipe inside the dust-catcher shell is 42 ft. high and is 19 ft. 7 in. in diameter at its bottom lip where it releases the gas inside the dust catcher. The ratio of the area of the inside cone at its bottom lip to the

Jan 1, 1943

By Clarence Zener

IT has long been known that the density of a metal usually decreases with cold-work. Thus O'Neilll observed as early as 1861 that cold hammering of commercial hot-rolled copper is accompanied by a decrease of density of 0.2 per cent, and that subsequent annealing restores the original density. The origin of this density change, however, has remained obscure. In particular, experiment has not yet decided whether it is due to the presence of small cavities and an increase in inter-granular surface or to an actual expansion of the lattice itself. This uncertainty in the origin of the change in density is a reflection of our uncertainty as to the changes induced in a metal by cold-working. One school regards cold-working as a breaking up of the original grains into a large number of perfect crystallites somewhat randomly orientated with respect to one another.2 According to this viewpoint, the mere introduction of a large intercrystallite surface induces a net volume expansion. Another school regards cold-working primarily as a distortion of the grains. It is not obvious that this second viewpoint will lead to a net volume expansion. The purpose of the present paper is to show that this is indeed the case, and that this expansion is of the right order of magnitude to explain existing experimental data. The physical basis for the association of an expansion with distortion lies essentially in the variation of the elastic moduli with volume. This variation is considerable. Thus from Table I we see that a I per cent increase in volume for the case of copper will decrease the bulk modulus K by 10 per cent, the shearing modulus µ by 3.8 per cent. If we thus twist a rod through a given angle, we shall do less work upon it if it increases slightly in volume, thereby reducing the torsion modulus that involves as a factor the shearing modulus. A general principle3 in physics states that the rod will so adjust itself as to have a minimum potential energy consistent with the end restraints. It will therefore expand. In order to obtain a quantitative comparison with experiment, we follow Maier4 in comparing the lattice expansion with the latent energy of cold-work. This latent energy has been measured directly by Taylor and Quinney5 on copper rods subjected to torsion, and may amount to as much as 15 per cent of the total work done upon the specimens. We shall assume that this

Jan 1, 1942

By F. M. Lewis, J. F. Meyers

This second progress report of grinding presents comments regarding ball consumption and data pertaining to the hydroscillator, which is closed circuited with the tricone mill. A study and postulate of how balls function is presented. The paper summarizes cost reduction obtained by the method of "grinding for the tail race" rather than for "mesh tons." AT the Regional meeting in Columbus, Ohio, in September 1949, the authors presented a progress report of the first year's operation with a Hardinge tricone mill in closed circuit with a Dorr hydroscillator. The present report covers our findings on this grinding circuit to January, 1950. In order to clarify our position, the authors wish to state that no invention or discovery is claimed. The Tennessee grinding circuit is simply an engineered arrangement of known equipment arranged to incorporate all of the recognized efficiency factors of comminution as they are known today. As we concluded our first report, it was not clear how effective the Tennessee mode of operation would be on harder ores. The only information we had at that time was that the Bond grindability test at 48-mesh gave 6.04 g of undersize per revolution. A later test on the same sample at 100-mesh reduced this to 2.04 g, which is definitely in the harder ore class, and which makes the reported 8.80 kw-hr per ton of —200-mesh produced a very creditable figure. Hydroscillator Operation The machine as now developed has proved dependable and easy to operate. It starts easily under full load and responds quickly to operating adjustments. The hydraulic holes in the oscillating plate do not plug when shut down under full load. Absolutely clean hydraulic water is essential. An Elliott water screen or similar device should be an essential part of the machine to keep all scale and trash of all kinds from the hydraulic compartment. The shift operators have expressed approval of the machine. In table I we show a typical screen analysis of the hydroscillator rake sand as compared to conventional classifier rake sand on our ore. We have previously reported that of the 28.7 pct reduction in power, the hydroscillator contributed 6 pct, on a —200-mesh basis. This is a conservative figure. Some of our test runs indicated that the saving was as high as 10 pct. Laboratory studies by the Dorr Co. engineers indicate that still greater efficiency is possible. Nevertheless, the 10-ft plate is overflowing 2100 tons per day at 3 to 4 pct + 65-mesh, which is a very creditable performance by

Jan 1, 1951

By E. T. Turkdogan, P. Grieveson

Experimental results are given for the rate 0.f solution of nitrogen in y iron in the temperature range 1000° to 1200°C. It is shown that, when purified reacting gas is used, the rate-controlling process is the diffusion of nitrogen into the iron. The difhsiuity of nitrogen in y iron is calculated from the results and the equation logD = —(8800/T) — 0.04 is recommended to represent the temperature dependence of the diffusivity. In some experiments using unpurified nitrogen, solution rates are found to be slower than those attributable to a solely solid-state diffusion process. Indications are that in the presence of impurities in the gas, e.g., H,O, chemisorption of nitrogen at the surface is hindered and becomes a rate-controlling process for the transfer of nitrogen across the gas -metal interface. ALTHOUGH the solubility of nitrogen in y iron at known nitrogen activities has been well-established,'-a the kinetics of the solution of nitrogen in iron are not known. The work of Darken, Smith, and Filer' indicates that at temperatures below about 1300°C the rate of solution of nitrogen in y iron is controlled by a chemical reaction at the metal surface, while at temperatures above about 1300°C the rate-controlling process is the diffusion of nitrogen in the metal. Fast and verrijps studied the denitro-genization of y iron using wet hydrogen at 950°C and their results clearly indicate that the rate of nitrogen removal is controlled by diffusion of nitrogen in the metal. In Part I of this series of papers, the kinetics of the solution of nitrogen in y iron are discussed in the light of the present experimental work. EXPERIMENTAL Apparatus. The reaction chamber consisted of a platinum wire-wound resistance furnace with a re-crystallized alumina reaction tube. The temoerature of the furnace, which was automatically controlled to approximately 1°C, was measured with a Pt/Pt-13 pct Rh thermocouple and a potentiometer. The temperature distribution in the working zone of the furnace was determined using a calibrated Pt/Pt-13 pct Rh thermocouple and the hot zone was found to be approximately 3 in. long with a temperature variation of * 3°C. A series of experiments was also carried out at 1000°C and pressures above atmospheric using a pressure vessel which was similar in construction to that described elsewhere.1° Materials. Ferrovac E grade iron used in all ex-

Jan 1, 1964

By John Guillermo Bartram

The oil industry continued relatively quiet in Wyoming in 1935, although production increased about 8 per cent over the previous year; 55 oil wells were completed in 1935, compared to 34 in 1934, and at the end of the year 44 wells were drilling, 33 in proven fields and 11 in wildcat locations. The total drilling a year ago was only 30. In the year 1935 Wyoming produced a total of 13,451,000 bbl. of oil, a gain of 912,000 bbl. over the 1934 figure of 12,539,000 bbl. Approxi-mately two-thirds of the increase, or 630,000 bbl., was from black oil fields and one-third, or 285,000 bbl., from light oil pools. Salt Creek, with production of 6,357,000 bbl., is still many times the largest field in Wyoming but in 1935 it made less than 50 per cent of the state's total, after producing more than all other fields in the state for 24 years; however, its decline was only 3.8 per cent from the previous year. Oregon Basin, a black oil field, held second place again with production of 1,163,-000 bbl., a good increase over 1934. Grass Creek, with increases in both its light and black oil, jumped into third place; and Lance Creek, with its new Sundance light oil production, was in fourth place in the amount of production. Frannie, which was in third place in 1934, dropped far back on the list because of lack of market. Byron and Garland, two other black oil fields in the Big Horn Basin, increased considerably. Big Muddy, a prominent light-oil field, was down with a natural decline; and Elk Basin, also light oil, produced less because of market conditions. During 1934 only three gas wells were drilled in Wyoming and 29 dry holes, 13 in proven fields and 16 at wildcat locations. Of the latter, 5 were on wildcat structures of considerable interest. Of the 55 wells completed during the year, 53 were in proven fields and of these 17 were small ones in the shallow Osage field and 10 were light-oil wells good for 1500 to 3000 bbl. each in the Lance Creek field. Discoveries Two of the oil wells were discoveries at Medicine Bow and Sheep Creek. Medicine Bow is a very large anticline with more than 3500 ft. of closure and is located in Carbon County in the south-central part of the state. In 1923 it showed some oil in the Upper Cretaceous Frontier

Jan 1, 1936

By Paul B. Crawford, Bobby L. Landrum

Electrical model studies have been made of the effect of unsymmetrical vertical fractures on production cnpacity. The study war restricted to the case of two vertical fractures originating at the well and extending out into the reservoir for various distances and orientations. The ratio of the short fracture length to the long fracture length was varied from 0.1 to 1.0 in successive studies. The angle separating the two fractures was varied from 0 to 180 degrees. The most effective fractured patterns were obtained when the fractures were oriented 180 degrees. It was found that when the total fracture length was equal to 0.2 of the drainage radius, the increase in production capacity may vary from approximately 1.55 to 1.95. depending upon the ratio of the short fracture length to the long fracture length and the angle separating the two fractures. If the total fracture length were 0.5 of the drainape- radius. poroduction cavacitv., increases varving 1.95 to 2.65 were observed, depending on the angle between the fractures and the ratio of the .short fracture length to the long fracture length. The fractured well production capacity decreased aPproxin?ately I to 10 per cent as the angle separating the fractures was varied from 180 to 90 degrees. It was dependent on the particular fracture. The commercial application of reservoir fracturing techniques has caused an interest to be expressed in the effect of vertical and horizontal fractures on production capacities. Some data have indicated that substantially vertical fractures may be created in some reservoirs. It is believed that the fractures are possibly unsymmetrical, that is, one fracture may extend due north 100 ft and a second fracture on the opposite side of the well may extend south or southeast only 50 ft. The total fracture length, ratios of the lengths and angles of separation may vary considerably. For this reason variations in these factors were considered. The study was restricted to the case of two vertical fractures originating at the well and extending out into the reservoir. It is not known that such will occur in a reservoir, but the results may be of value in interpreting or studying fracturing applications. PROCEDURE An electrical model was used in this study of the effect of unsymmetrical vertical fractures on production capacity, A wooden tank 30 in. in diameter and approximately 2 in deep was coated with paraffin wax. A copper band was situated at the periphery and a single wire electrode was positioned at the center of the tank. The ratio of the reservoir radius divided by the

Jan 1, 1956

By J. S. Westwater

The Mather mine of The Negaunee Mine Co. embraces nearly all of Sections 1 and 2, T47N, R27W, within the limits of the cities of Negaunee and Ishpeming on the Marquette iron range of Michigan's Upper Peninsula. Operations of the Negaunee Mine Co., the stock of which is jointly owned by Bethlehem Steel Co. and The Cleve-land-Cliffs Iron Co., are under the direction of the latter company. The opening of the Mather mine was described by C. W. Al1en.† Mather " A " shaft was completed to an initial depth of 2352 ft in early 1943. The shaft capacity of over one million tons yearly is in prospect of being realized by orderly development and mining, and sinking of the second or "B" shaft then started in accordance with previous planning. Mather "B," also a vertical shaft, was designed as a twin to Mather "A" shaft and the sinking technique developed at Mather "A" was utilized in "B" shaft operation. Shaft Sinking General Plan An average depth of 16 ft of sand overburden at the shaft site was cleared away by bulldozer, and the shaft approximately 15 by 20 ft in rock opening put down to an initial depth of 87 ft. Mucking of the broken rock to this depth was accomplished by an Insley excavator equipped with a 1/2 yard ca-pacity Owens clamshell bucket. Addition of 200 lb weight to each lip of the clam bucket provided adequate "bite" to dig the broken diorite and jasper rock. Temporary heavy wood bearers were placed across the shaft mouth to support the steel shaft sets which were hung in this initial 87 ft depth, aligned accurately and concreted in place from the lowest set upwards. The permanent steel headframe foundations and three service tunnel openings to the shaft were also concreted in the upper section to the shaft collar. A temporary wood headframe was then erected over the shaft mouth, and initial hoisting machinery assembled consisting of a Lake Shore 12 ft diam single drum grooved for a 1 3/8 in. rope and powered by two 400 hp motors to attain hoisting speed of 1100 fpm. Compressed air was obtained from a Nordberg 2 stage tandem horizontal type with a capacity of 1500 cfm. An enclosed landing platform at the shaft collar was equipped with a rotary dump and pocket for discharge of the rock into a Euclid 15 ton truck. On completing assembly of this equipment and installation of a special cage in the shaft, sinking was resumed on a three shift, six days per week

Jan 1, 1950

By Frederick Laist

0. C. RALSTON, Salt Lake City, Utah.-I have merely glanced over this paper, consequently, I am hardly in a position to discuss it intelligently. There is one thing, however, that is of interest, that is, the claim that the oil mixture which they have chosen is the best adapted to the work at hand. I would like to ask Mr. Mathewson if they still feel that that is the case-if that really does give the best grade of concentration and the best extraction for the same money, compared to any particular oil mixture which they could get. E. P. MATHEWSON, Anaconda, Mont.-We are still using that mixture, and we consider it the most economical mixture used. DAVID COLE, El Paso, Texas.-I would like to ask Mr. Ralston if there are some other mixtures that would be better? E. P. MATHEWSON.-We are open to suggestions. 0. C. RALSTON.-My own paper on oils* calls attention to the fact that certain hardwood oils, especially the tars, are now being burned or wasted. A great deal of hardwood tar is available as low as 4 or 5 c. per gallon, that being its value as fuel under the boilers. As a matter of fact, a great deal of testing has been done with only the commercial products that are as a usual ride sold on the market. Very little hardwood tar is sold on the market. In asking a great many people who have tested flotation oils, I have not heard hardwood tar mentioned very often. I think I would add to that that the hardwood tars can probably be bought in quantity comparable with the sludge acid at Anaconda, and. should contain a greater proportion of the frothing constituent, and at a price fairly commensurate with what they pay for the sludge acid. E. P. MATHEWSON.-I would like to make a correction in one statement I made that there has been no change made in the mixture. This change has been made: We found that the amount of wood creosote in treating the sand from tables was extremely small, and we tried some experiments on a large scale, dropping it out and using simply the sludge acid and sulphuric acid. We found that this gave practically as good results as wood creosote. We use wood creosote in treating the slimes. We find it necessary in that operation. DAVID COLE.-I would like to ask, what is sludge acid?

Jan 10, 1916

By Roy C. Kirkman

Dear Editor: It is with great pleasure that I read Mr. Howard M. Wells article in the December 1978 issue of MINING ENGINEERING entitled: "Optimization of Mining Engineering Design in Mineral Valuation." Mr. Wells very adequately presents the case and point that there are a great number of variables which must be analyzed during an economic evaluation of an FUND RESOURCE, such as copper or uranium. I wish to take this opportunity to suggest that, given today's economic climate, decision making takes place under conditions of uncertainty and that this uncertainty justifies our need to examine each one of the parameters entered into the evaluation model. It is my contention that the influence of the tonnages and grades as well as their distributions, have the most profound effect upon the results of an evaluation. Everyone concerned with the evaluation of FUND RESOURCES realizes that as metal prices decline or stagnate with sharply rising direct operating costs, cutoff grades (Gc) must increase according to the equation below which Mr. Wells uses: Gc = Total Operating Cost/(Market Price X 20 X Recovery) However, historically, we have seen cutoffs move dramatically lower in both the copper and uranium industries for the past decade. Henceforth, this established the metals industry most important argument for processing greater tonnages of lower grade materials from disseminated deposits (refer to paper by Kirkman, Roy C.). These disseminated deposits, created by either concentration processes (uranium) or dispersion processes (copper, gold, molybdenum), have log-normal grade distributions (Fig 1). Gross profits are rising, but unit profits are falling. The industry has created longevity through economy of scale, i.e., mining vast tonnages of low grade. In order to develop the great tonnages necessary to prove economic viability, we must examine alternatives at the low-end of the tonnage grade relationship. Notice from [Fig. 2] that as we move further to the right away from line A-B drawn tangential to the average grade curve at 45°, total profits will increase (given fixed annual production capacity) and unit profits decrease. The theoretical optimum operating point is where: [ ] At this point my observation is that slight shifts in production capacity bring about greater changes in profitability due to greater grade changes. Therefore, the best financial risk evaluation is obtained by totally revising the mining engineers methods and fixing the financial parameters such as discount and interest rates. A 10% shift in either of these two parameters will not cause near the same variance in economic viability as will a change on the GRADE-TONNAGE curve [(Fig. 2)].

Jan 1, 1980

By J. A. Lund, A. M. Lawson

THE structures of quenched eutectoid and hypereu-tectoid Fe-Cu alloys have been examined by X-ray diffraction and by optical and electron microscopy. The relevant portion of the Fe-Cu phase diagram is given in Fig. 1. Several values have been reported for the solubility of copper in a Fe at the eutectoid temperature, including 1.4 wt pct by orton' and 2.13 wt pct by Wreidt and Darken.2 Alloys containing 4.8 and 7.5 wt pct Cu have been prepared from two batches of Ferrovac E iron (0.005C and 0.013C) and electrolytic tough pitch copper (99.90 Cu). Specimens of dimensions 0.8 by 0.8 by 0.1 in. were cut from hot-rolled material, austenitized, and quenched into brine at 25°C. Similar specimens were also cooled in the furnace, after a short soaking treatment at 1100°C, at a rate estimated to be 10°C per min in the temperature range of 900" to 500°C. X-ray diffractometry was performed on quenched and on furnace-cooled bulk specimens using iron radiation. Only a bcc phase could be detected in all samples. Lattice parameters were calculated from measurements on four lines, made up of two resolved high-angle doublets. Comparisons were made against a silicon standard. Results are shown in Table I. Based on X-ray diffraction studies of a series of alloys of lower copper concentrations, orton' estimated that the tattice constant of a Fe at 25°C increases 0.0014A per wt pct Cu in solution. Extrapolating Norton's data, it may be concluded that all copper was retained in solution in the brine-quenched 4.8 pct Cu alloy, and that approximately 5 pct Cu was also held in solution on quenching the 7.5 pct Cu alloy. Typical microstructures of brine-quenched specimens, as observed by optical microscopy, are shown in Figs. 2 and 3. Precipitation of the E phase (copper-rich) occurred along the y grain boundaries on quenching the 7.5 pct Cu alloy, rendering them readily detectable in the microstructure, Fig. 3. The original boundaries in the 4.8 pct Cu specimens were gener- ally not discernible, however. This indicates that the z phase which was seen in the higher-copper alloy was probably of proeutectoid origin. Thin foils for transmission electron microscopy were obtained from bulk specimens by spark machining to 0.006 in. thickness, followed by electrolytic polishing. Typical transmission electron micrographs

Jan 1, 1967

By C. P. Clingerman

The recent iastallation of a combination dust catcher, gas washer and precipitator at Carrie blast furnaces of the Homestead Steel Works has given very satisfactory results. The following description of the gas-cleaning installation is based on actual operating experience. When Carrie blast furnace No. 3 was rebuilt the decision was made to fine-clean all the gas produced by the furnace, because the management wanted fine-cleaned gas for fuel in the stoves and boilers. In order to keep the installation cost as low as possible, the gas-cleaning system was streamlined. All by-pass lines and goggle valves for bypass lines were eliminated from the system. A radical departure from the use of 8-in. tubes in the Cottrell-type precipitators was made by using 12-in. diameter tubes in a single compartment, the single compartment being divided into two units by a single partition wall in the top header. The Furnace Proper A few of the characteristic points and dimensions of the furnace proper are: Hearth diameter.............. 26 ft. o in. Bosh diameter............... 29 ft. 1 3/4 in. Stock-line diameter........... 20 ft. o in. Large-bell diameter........... 14 ft. 8 in. Small-bell diameter........... 6 ft. 6 in. Height of furnace from center of iron notch to bottom of large bell, closed............ 94 ft. 4 in. Height of furnace from center of iron notch to main platform ...................... 105 ft. o in. The furnace top is equipped with a MC-Kee revolving distributor, the operation of which is electrically interlocked with the skips, bell hoists, and coke-weighing and charging apparatus through a Freyn automatic charging control. The gas leaves the furnace first through four offtakes, 5 ft. 9 in. in diameter, then through uptakes that, are approximately 85 ft. high, which feed into a single down-comer that is 9 ft. in diameter. Dust Catcher The primary dust catcher installed (Fig. I) may be described as a single-cone type. The inlet pipe at the top of the dust catchei is 9 ft. in diameter; it is flared to a conical shape as it extends down inside the dust-catcher shell, which is 35 ft. in diameter, 37 ft. high on the straight side, and has a conical top and bottom. The slope of the bottom is so0 with the horizontal. The cone-shaped pipe inside the dust-catcher shell is 42 ft. high and is 19 ft. 7 in. in diameter at its bottom lip where it releases the gas inside the dust catcher. The ratio of the area of the inside cone at its bottom lip to the

Jan 1, 1943

By Waldemar Dyrssen

I CANNOT agree with the results obtained by the committee. The gas obtained per pound of coal is too high in calorific value and the amount of gas is too large. It should require about 190 cu. ft. of oxygen per 1000 cu. ft. of gas and not 75.14 cu. ft. as is given on page 35 of the report, or about 2.5 as much. Calculating the calorific value per pound of coal from the coal analysis given on page 34, according to Dulong's formula, the gross and net calorific heat are about 12,890 and 12,430 B.t.u., respectively, which is about 18,600 and 17,900 B.t.u., respectively, per pound of carbon in the coal. This is an unusually high figure, as ordinary bituminous coal has less than 18,000 gross B.t.u. per pound of carbon. Assuming, however, that the calorific values calculated are correct, the following results are obtained. On page 35, the net calorific heat in the gas per pound of coal is given as 12,856 B.t.u. and calculation for the gross value shows it to be about 13,950; in other words, the gas contains (13,950 - 12,890) ÷ 12,890 = 8.2 per cent. more heat than the coal on a gross basis and (12,856 - 12,430) ÷ 12,430 = 3.4 per cent. more on a net basis. The calculated amount of carbon in this gas per pound of coal gasified is about 0.688 lb., or nearly the same as in the coal (0.6972) and the gross and net calorific heat per pound of carbon in the gas are 20,300 and 18,710 B.t.u. which are 9.1 and 4.5 per cent. more than for the carbon in the coal. These calculations show that the results given in the report cannot be correct. There must always be some heat losses in the gasification of coal, in radiation from the producer, and in sensible heat in the gas; there must be some loss of carbon in ashes and in soot, and there are always tarry vapors in the gases that are condensed and do not appear in the fixed gases. From the excessive heat in gas per pound of carbon contained therein, it can also be concluded that the percentage of hydrogen in the gas is too high, from which it follows that the moisture decomposed is too high and that more free oxygen must be used.

Jan 11, 1924

By J. W. King

URANIUM ore was first discovered in the Edge-mont district of the southern Black Hills in the summer of 1951. The discovery was not made known for some time, but after the news leaked out prospecting became intense, and several hundred claims were staked in the spring of 1952. The Hot Springs Sub Office of the Atomic Energy Commission was established at that time and airborne radiometric surveys were commenced by the Government and by private companies. During the succeeding summer another important discovery was made by private airborne surveys in the northern Black Hills, and the area favorable for uranium ore was expanded many times. Between that summer of 1952 and the present, many individuals and groups have explored, developed, and exploited their claims until now uranium ore is produced in significant quantities and substantial reserves have been developed. The Black Hills portion of the geologic map of the U. S. issued by the U. S. Geological Survey is shown in Fig. 1. Sedimentary formations are exposed as a series of cuestas and hogbacks in a roughly annular pattern with the older sediments resting on the pre-Cambrian core, which is exposed in the eastern and southern portions of the dome. The South Dakota-Wyoming state line bisects the area from north to south. The Cheyenne River crosses the southern tip of the Black Hills and the Little Missouri bounds them roughly on the north. Headquarters of the AEC in the Black Hills is the Sub Office at Hot Springs, S. D. An ore buying station is located in Edgemont, 28 miles to the southwest, where a mill is presently under construction. The area of original uranium ore discovery and of principal activity in the southern Hills is a few miles north of Edgemont. Several areas of anomalous radioactivity have been noted between Dewey, S. D., and Newcastle, Wyo. A limited amount of ore has come from the Dewey area and private exploration is active there. The Carlile deposit, largest producing mine in the northern Black Hills to date, lies northwest of the Belle Fourche River near the western extremity of the Hills. Two of the larger known orebodies of the area are located near the Little Missouri River where a small window exposes the favorable strati-graphic horizon of the Fall River sandstone. Small production has recently come from Barlow Canyon, near Devils Tower, Wyo., Fig. 2, and numerous areas of anomalous radioactivity are known in the vicinity. Three producing deposits and scattered radioactivity are found along the state line east of Aladdin, Wyo. Several areas of weakly anomalous radio-

Jan 1, 1957

By Grover J. Holt

A DETAILED description of the many variations in iron mining and transportation practice in Minnesota would require much space. Since a fairly detailed description of the practices then in use was published in the guidebook issued in connection with the meeting of the Institute on the iron ranges in I920, and subsequent developments have been described by E. E. Hunner,1 M. H. Barber,2 and A. E. Anderson, J. M. Riddell and G. J. Holt,3 it will not be necessary here to do more than review the highlights of current practice. Details on any points of interest can be obtained through correspondence with the operators involved. [T] The iron ores of Minnesota, which have been formed through enrichment of the iron formation in which they occur, largely by the removal of silica, are usually covered by a blanket of glacial drift known locally as "surface." Surface material, including sand, clay, hardpan and boulders, makes up the greater portion of the stripping in open-pit operations. In some instances, stripping also includes taconite and "paint rock," directly below the surface material and overlying the ore. Taconite is the iron formation, a ferruginous chert with interbedded slate layers. "Paint rock" is a local term for oxidized slate layers interbedded in the iron formation, high in phosphorus, alumina and moisture. The iron ores fall into two classes: (I) direct shipping (merchantable ores or ores requiring no treatment except possibly crushing or screening to make an acceptable sized product), and (2) ores requiring beneficiation (such as sintering, drying, washing, jigging, high-density treatment, or magnetic separation in the case of magnetite). The Mesabi Range produces chiefly soft Bessemer and non-Bessemer ores. The Cuyuna Range produces mainly low-manganese brown ore and high-manganese black ores, with some iron ore. The Vermilion Range yields mainly Besse¬mer and non-Bessemer iron ore, with some hard or lump ore that finds use in the open hearth. Open-pit mining is limited to the Mesabi and Cuyuna Ranges but underground mining is done on all three. The choice of mining methods is determined by the relative economics of overburden¬-removal and shaft-mining costs. STRIPPING PRACTICE Common practice has been to remove the bulk of the overburden during the winter season and to mine during the summer. In the present emergency many operators are forced to forego the economies attained by year-round utilization of equipment and to equip for, and carry on, stripping and mining simultaneously. In the normal years or lean years to come, most properties probably will be over-equipped and high depreciation charges will have to be absorbed.

Jan 1, 1942