Search Documents

By O. Katz, A. Spilners, M. Simnad

THE oxidation of titanium has been studied in recent years by a number of investigators.'-W ne of the most important aspects of the reaction of titanium with oxygen, which has been observed by several of the investigators, is the extremely high solubility of oxygen in the metal. A detailed study of the Ti-0 systeml% as shown that the solubility limit of oxygen in a-titanium is approximately 14.5 wt pct 0 from 800" to 1700°C. The unusual oxidation behavior of titanium may be ascribed to this phenomenon, since part of the oxygen uptake enters into solid solution in the metal and only a part is available for scale formation. A more complete study of the kinetics of oxidation of titanium would require information on the influence of oxygen in solution in the metal upon the oxidation rate. Such information would also be of interest in regard to the theory of oxidation of metals. The authors have measured the oxidation rates of oxygen-saturated and oxygen-free titanium between 800" and 1200°C and have found appreciable differences in their rates of oxygen uptake and in the activation energies. The experimental set-up was similar to that described in a previous paper.u The course of oxida-dation was followed continously by attaching the specimen to a sensitive spring balance and observing the extension of the spring with time of oxidation. High purity electrolytic oxygen was used and precautions were taken to purify the gases employed. The specimens were prepared from iodide titanium and were ground on metallographic polishing papers to a fineness of 4/0. The furnace was first evacuated and filled with argon; the specimen was lowered into the furnace, which was then evacuated and filled with oxygen, after the specimen had reached the oxidation temperature in argon. The samples were presaturated with oxygen by means of the following procedure: Each specimen was first heated in oxygen at 1200°C until its increase in weight indicated 13.8 pct by weight uptake of oxygen. The furnace was then immediately evacuated and filled with purified argon five times. The specimen was heated in the argon atmosphere for a period of 72 hr at 1200°C in order to saturate the metal with oxygen by complete absorption of the scale. The temperature was lowered to the oxidation temperature, the furnace was evacuated and filled with oxygen, and the oxidation rate was followed by noting the extension of the spring balance. No oxide film was visible on these specimens at the start of the oxidation experiments. Titanium samples in the oxygen-free as-received condition were also oxidized and their oxidation rates measured. The results are shown in Figs. 1, 2, and 3, which indicate that the initial rates of uptake of oxygen by both the oxygen-saturated and oxygen-free specimens are parabolic at these temperatures. The rate of uptake of oxygen is, however, appreciably lower

Jan 1, 1956

The Climax Molybdenum Company' s newest operation is the Henderson project, which is located on the east side of the Continental Divide. Ore reserves are estimated at more than 300 million tons at a grade of 0.49% MoS2. For mining the ore a modified panel caving system is used. The ore is transported to the Henderson mill on the west side of the Continental Divide on a 42 in. (1.07 m) gauge railroad through 9.6 miles (15.4 km) of tunnel and 4. 8 miles (7.7 km) of surface track, a total distance of 14.4 miles (23. 2 km). Each train consists of 30 ore cars with capacity of 22 st (20 mt) of ore or 660 st (599 mt) per train. The unmanned trains operate completely automatically. At the 54 in. by 84 in. primary gyratory crusher, the bottom dump ore cars pass over a dump scroll to discharge at a maximum rate of 100 st (91 mt) per minute. Dumped ore falls onto a rock box before passing over a 17 ft long by 46 ft wide (5. 2 m by 14 m) grizzly set at a 40° angle with bar spacings of 7 ½ and 8 ½ in. (191 mm and 216 mm) openings. An estimated 30 to 50% of the ore (which at times is wet and sticky) passes through the grizzly. The operators report that a shallower angle on the grizzly, perhaps 35º to 37º, would have been sufficient and would have prevented impact on the back of the crusher pocket by large boulders. This pocket as well as the crushed ore pocket under the crusher is lined with AR plate. The accompanying drawings show a "future splitter" and the operators are planning the installation of this unit to prevent impact and subsequent damage to the crusher spider. Crushed ore at an 8 to 9 in. (203 mm to 229 mm) size joins the grizzly undersize in the pocket beneath the crusher. This pocket is sized at 660 live st (599 mt) so that it will accept an entire trainload of ore. Crushed ore is removed from the pocket by a four-speed, 84 in. (2. 1 m) apron feeder operating at 9.6 to 29. 3 fpm (2.9 to 8.9 mpm). A 60 in. (1.5 m) takeaway conveyor operating at 480 fpm (146 mpm) delivers the crushed ore to a 58,000 st live and 193,000 st total (52,600 and 175, 100 mt) open stockpile under an A -frame supported tripper gallery. Impact idlers on the takeaway conveyor under the apron feeder discharge are mounted on wood blocks for a cushioning effect and ripped belt detecting bars are located behind each impact idler. The conveyor tunnel is of corrugated and galvanized steel construction rather than concrete. The concrete crusher enclosure is circular in design from its lowest level at elevation minus 110 ft 4 in. (minus 33. 6 m) to elevation

Jan 1, 1978

By A. J. Boyer, T. R. Meadowcroft

An experimental determination has been made of the efject of surface diffusion on the vapor pressure obtained in a Kwudsen cell. The results show that a knife-edge orifice in a molybdenum lid may give erroneous results for the vapor pressure of silver. when a correction suggested by winterbottom and Hirth is made, the results become meaningful. Experimental work with cylindrical orifices in molyhdenz~m lids and knife-edge orifices in ceramic lids shows that good vapor-pressure results may he obtained when the orifice is designed so that ejfusion is the only significant source of weight loss. THE Knudsen effusion cell technique has been used by many investigators to study relative and absolute vapor pressures over metals and alloys at elevated temperatures. As a result of this interest, some theoretical studies have been made of geometric factors affecting effusion from the orifice of a Knudsen cell. A review of these studies has been made by Margrave.1 Recently, Winterbottom and Hirth2 have suggested that a physical effect, that of condensation, surface diffusion, and re-evaporation, may seriously affect Knudsen cell measurements, especially when a knife-edge orifice is used. Inasmuch as many of the present vapor-pressure data have been obtained using knife-edge orifices. it was felt that an experimental evaluation of the effect of surface diffusion on Knudsen cell measurements would be of value both in the design of the cell orifice and in establishing realistic estimates of the limits of error for existing data. The experimental program was in two sections. Firstly, measurements of the vapor pressure of silver were made in cells with cylindrical and conical orifices in which the surface-diffusion contribution to the weight loss should be negligible. These results were correlated with existing data to give a reliable measure of the real vapor pressure of silver. Secondly, measurements made using knife-edge orifices were corrected using the surface-diffusion theory of Winterbottom and Hirth2 and were then compared to the real values. The experimental arrangement is shown in Fig. 1. The balance was an Ainsworth RV-AU-1 automatic recording microbalance capable of measuring weight changes of ±0.02 mg on a total load of up to 100 g. The temperature was measured by an optical pyrometer signted on the bottom of the suspended crucible. The temperature readings were calibrated in a separate experiment in which pyrometer measurements were made while at the same time thermocouple readings were taken of the temperature at the inside top and bottom of the crucible. The range of reproducibility with this technique was ±4°C. A constant voltage source maintained a temperature of ±2°C at 1200°C over 10 hr. Silver of 99.99 pct purity was used in nonporous alumina crucibles. Lids of molybdenum, tantalum, or magnesia were cemented to the crucible using a sodium silicate cement. Table I shows the characteristics of the lids used. The vapor pressure is obtained using the basic Knudsen formula:

Jan 1, 1965

By Richard M. Foose

MOST of the roofing granules produced in Pennsylvania are made by two companies at three plants. The Advance Industrial Supply Co. has three quarries and a mill at Gladhill Station, in southern Adams County. The Funkhouser Company is actively engaged in mining, quarrying and milling at Charmian, about one mile west of Gladhill Station, and at Delta, in southern York County. These three plants produced approximately 100,000 short tons of granules in 1943. The production of roofing granules in 1937 for the whole country was only about 500,000 tons, generally indicating the large growth of the industry since that time. The fundamentals of producing roofing granules were discussed comprehensively by G. W. Josephson in a paper before the Industrial Minerals Division in October 1943 (Mining Technology, March 1944). The purpose of this paper is to describe the actual methods of mining the rock and milling it to make roofing granules, as practiced by the three Pennsylvania plants. MINING AND MILLING Funkhouser Company (Delta) The Funkhouser Company, near Delta, in southern York County, Pennsylvania, operates three joined quarries and a mine in the Peach Bottom slate. The joined quarries extend 1200 ft. in a northeast southwest direction along the strike of the slate cleavage and are about 200 ft. wide. The working face is about 45 ft. high. The quarrying operation is rather simple: Ingersoll-Rand Jackhamers, 1-in. and 1 1/4-in., with hollow drill steel, are used to undercut the quarry face with10-ft. holes. The face is "blown" and allowed to slump on the quarry floor. Loaded by a Marion electric shovel into trucks, the shattered rock is taken to the primary crusher 2500 ft. away. In addition to the normal quarrying operations, a drift into the northeast wall of the middle quarry was begun about 1935 and has advanced about 2000 ft. since then. Rooms have been driven at angles to the drift along choice beds of slate. The drifts and rooms have a roof more than 35 ft. high and the main drift and rooms are all more than 40 ft. wide. There is no cribbing at any place in the mine. Several of the rooms were driven upward on a 5º slope and in some of them there was stoping. Ingersoll-Rand Jackhamers are used, and only wet drilling is practiced. When visited in January 1940, an electric shovel was operating at the head of the drift, scooping up the slate blasted out of the working face. This, too, is trucked to the primary crusher. Some of the better quality slate is saved for making slate shingles. The primary crusher, which is a No. 30 McCulley gyratory, receives the slate from the trucks and crushes it to about 2-in. size (Fig. I). This product travels by a 30-in. belt conveyor to Niagara vibrating screens with 2-in. holes. The minus 2-in. product moves to a storage silo by bucket

Jan 1, 1945

By C. E. Birchenall, M. H. Davis

The rate of oxidation of titanium in the temperature range 650° to 950°C has been measured. 'The linear rate law obtained is explained by interface reaction control of the process. Tracer experiments indicate the oxygen diffuses in at least one phase of the scale. THE kinetics of oxidation of titanium, principally at low temperatures and under varying oxygen pressures, have been reported.¹,² In the present investigation the rates of oxidation of titanium have been determined by the gravimetric method in the temperature range 650" to 1000°C under 1 atm of oxygen. Some of the scales formed were powdered and an endeavor was made to identify the phases present by X-ray diffraction. Alexander and Pigeon1 ascribe a logarithmic rate law to the growth of thick films formed at temperatures up to 565"C, and Gulbransen and Andrew' suggest that the parabolic rate law holds up to 600°C. In both cases large initial deviations from those relationships are apparent and no explanation is offered. In the present experiments it is shown that a linear rate law holds in the temperature range 650" to 1000°C, and it is suggested that the initial deviations observed are due in part to a spurious surface area effect and also to the high solubility of oxygen in titanium metal. Positive information on the mechanism of oxidation is not available, but oxygen ion diffusion through the lattice is inferred from the re- sults of trace experiments. X-ray analysis of the scale confirms Gulbransen and Hickman's' observation on the presence of rutile TiO². Experimental Details The titanium used in these experiments was prepared by the reduction of titanium tetrachloride with magnesium and was used in the form of rolled sheet. Samples approximately 0.040x0.5x0.75 in. were cut and polished to a fineness of 4/0 on metal-lographic polishing papers. Individual samples, suspended on a platinum wire, were lowered into the hot zone of a furnace, in vacuo, by means of a winch, and oxygen was admitted after the desired temperature was attained. The increase of weight of single samples oxidized for fixed times at certain temperatures was determined by weighing the sample before and after oxidation on a chemical balance. In these instances the sample was used for only one time at one temperature. In some cases the course of oxidation was followed by attaching the sample to a sensitive spring balance and noting periodically the extension of the spring with time of oxidation. Kirkendall type experiments were carried out by marking the surface of the titanium prior to oxidation with a solution containing radioactive silver. After drying, the specimen was heated in vacuo to decompose the silver nitrate used, leaving a small amount of metallic radioactive silver on the surface. Following oxidation, these samples were mounted, ground, and then placed in intimate contact with

Jan 1, 1952

By John Wulff

In a previous paper Burwell and Wulff1 have shown by electron diffraction studies that allotropic transformations can be induced in 18-8 stainless steel by polishing to a depth of about 5 X 10-5 cm. The development of a successful etching technique, which removes accountable amounts of metal from the surface without pitting and without changing the root-mean-square profile as measured with an Abbot pro-filometer, led to the application of the whole technique and material to an investigation of various mechanical methods of surface preparation, such as grinding, lapping, superfinishing and cold-rolling. Ideally suited to such a study is 18-8 of low carbon and nitrogen content. The material can be heat-treated to produce a coarse-grained single-phase structure. On cold deformation there occurs not only a reduction in grain size but, at regions of maximum stress, a change of face-centered material to body-centered material, provided the metal is worked below about 200°C. When worked between 200"about and 415°C., diffraction studies evidence a reduction in grain size without the appearance of any new body-centered ferrite. Ferrite, which can be referred also to strains induced by carbide precipitation, is evident when the material is worked at temperatures between 4150 and 800°C. Stainless steel is advantageous because the usual surface-finishing operations do not readily oxidize it to any appreciable depth. In order to produce detectable oxide films on the surface of austenitic 18-8 in a time equivalent to that required to produce, for example, a fine ground finish on 1/2 sq. in., the sample must be held in a furnace or oxygen stream above 600°C. By using longer heating times, it is possible to achieve measurable oxide films on samples , whose surface temperatures exceed only about 250°C. Experimental Procedure The apparatus, material, and technique described in the previous paper1 were employed in this investigation. Samples of 18-8, I by I cm. by 4 mm., were carefully annealed in the austenitic range to produce a coarse-grained structure. They were then quenched and pickled to remove scale, On a lapping machine of the Graton2 type, both sides of each sample were polished to a a of 1/6 a wave length of sodium D light. Thereafter they were electrolytically etched to remove at least 1 X 10-3 cm. of the surface, a depth that is well below that of any defermations induced by surface preparation. samples of this material, carefully mounted in steel holders, were then sent to various industrial organizations known for special finishing techniques. In the instrue ment shops at the Massachusetts Institute of Technology check samples were finished by the same methods, as far as they were available. Abbot profilometer3 readings Were made on all the samples, which were then carefully degreased in double distilled benzine and alcohol, dried in a hot-filtered air blast, and kept in a desiccator. SUC-

Jan 1, 1941

The San Manuel district of Arizona was first prospected prior to the Civil War, but there was little or no production until 1881. Small operators tried to develop ore bodies from time to time after that without success. Then, in 1917, a drilling program was carried out; but it did not indicate a copper content of interest. Finally, in the 1940s, the U. S. Geological Survey drilled the property and obtained indications of a mineralized area. At that time, Magma Copper and its principal owner, Newrnont Mining Corporation, drilled many deep holes through the gravels and conglomerates and in 1948 proved an ore reserve of 367 million tons of 0.785% copper sulfide ore. Underground exploration and development were started in early 1948, and in 1953 design and construction of the surface facilities commenced. By the end of 1955 plant construction was completed. The ore deposit of disseminated pyrite, chalcopyrite, chalcocite, molybdenite, silver, and gold is in quartz monzonite porphyry gangue. Mine production, which is entirely underground, is by full-gravity block-caving. Initially, ore mined at a rate of 36,000 tpd was hoisted through two identical shafts. From the 5,000 ton coarse ore bins located at the collar of each shaft, the ore was hauled by a shuttle service rail- road in 100-ton bottom-dump rail cars a distance of seven miles to the rail bin. Fragmentation from block-caving supplemented by underground grizzlies at the loading stations controlled the oversize material to give a feed size acceptable to the two 7 ft standard Syrnons crushers. During operation, however, it became evident that a large amount of secondary breaking in the grizzlies was necessary to produce a suitable feed for the standard crushers. The decision was then made to install primary gyratory crushers on the surface adjacent to the shaft site ore bins. Under each 5,000-ton coarse ore bin, an 8ft by 20 ft (2.44 m by 6. 1 m) apron feeder transfers the ore to a 13 ft 6 in. by 10 ft (4. 1 m by 3. 05 m) grizzly set at 6 in. (152 mm) and sloped at 45 degrees. About 65% of the ore passes the grizzly and thus bypasses the 42 in. by 65 in. (1.07 m by 1. 65 m) Allis -Chalmers gyratory equipped with a Hydroset mechanism and having an open side setting of 5 ½ in. (140 mm). Grizzly undersize and crushed ore drop onto a 6 ft by 30 ft (1. 83 m by 9. 14 m) variable- speed apron feeder for transfer to a 54 in. by 90 ft 5 in. (1.37 m by 27.6 m) inclined conveyor equipped with a tramp iron detector. Indication of tramp iron automatically stops the conveyor and both apron feeders. When the iron is removed from the belt by the operator,

Jan 1, 1978

By Louis A. Panek

The purpose of this paper is to present a method of designing safe and economical arch structures that are to be constructed of concrete or directly of original earth materials. The experimental data used to illustrate the design method are taken from Bucky and Fen tress,1,2 and the application of the ideas presented by them is extended by obtaining an additional set of curves from which arch structures may be designed. This design method is based upon the following principles of similitude: A scalar model made of the same material as that of the full sized structure will behave similarly to its prototype if the density of the model is increased in the same proportion as its linear scale is decreased. Let R represent the scale or model ratio, namely, the ratio of a prototype linear dimension to the corresponding model linear dimension. The effect of increased density may be obtained by rotating the model in a centrifuge at a speed such that the centrifugal held exerts on the model an accelerative force R times the accelerative force of gravity. Under these conditions; (I) model unit stresses are equal to corresponding prototype unit stresses, (2) the ratio of the prototype deformation at a given point to the model deformation at a similar point is equal to the scale ratio, R, and (3) the model and the prototype will behave similarly within and beyond the elastic limits of strain. According to the above relations, such models can be used to solve the following problems: I. The dimensions of the most economical safe arch structure for a given load. 2. The miaximum safe roof span underground for given geologic conditions. The procedure is described briefly as follows. Tests are made by rotating in a centrifuge a number of models that repiesent a variety of prototype loads and dimensions. From the experimental data, curves are plotted to show the relations between these loads and dimensions. The curves are used to solve directly the problems stated above. Structural design is based upon the working (safe) stress of the material of construction, which is established by applying a factor of safety to the experimentally determined ultimate strength of the material. In conformity with this principle, each model is gradually loaded until failure occurs. A safety factor is then applied to the results. If a safety factor of 4 is used, a given model at failure represents a safe prototype, the linear dimensions of which are equal to one-fourth the model ratio at failure times the corresponding model dimensions. The safe model ratio is computed from the following formula: Safe R =(1/4)4p2n2r/g=p2n2r/g [I] in which: n = centrifuge revolutions per second at model failure; r = radius of rotation of the model in feet; g = 32.2 ft/sec2.

Jan 1, 1949

By Cuppam Dasarathy

THE object of this note is to report briefly certain results of investigations on the Fe-In phase diagram. BISRA-high purity H-iron and 99.9 pct pure indium were used to prepare the alloys. The experimental techniques consisted of thermal analysis, optical metallography, and X-ray diffraction. A phase diagram based on the present results as well as those reported earlier by the author' is shown in Fig. 1. It is seen that the liquidus points fall on a smooth line which meets the monotectic isotherm at 1470°C. The liquidus extends up to 3.4 at. pct In. The phase boundary separating the two liquidus L1 and L2 is shown dotted. The experimental solidus meets the monotectic isotherm at -0.9 at. pct In. The 6/6 + L2 boundary drops steeply to the 6 + La/y + L2 boundary at -1350°C. In this region, it is impossible to detect satisfactory thermal arrests because of the steep phase boundary. The present diagram shows that indium lowers the temperature of the d/y transforma-tion and raises the temperature of the y/a transfor-mation. The y +d region is found to be very narrow. Indium gives rise to a restricted y field when alloyed with iron. The width of this field is between 0.4 and 0.5 at. pct In. Details of the alloys containing 40 and 50 at. pct In have already been reported by the author' and the transformation temperatures of these alloys are included in Fig. 1. It appeared from optical metallography and X-ray diffraction that the room temperature solubility of indium in a iron is less than 0.28 at. pct since alloys of 0.28 at. pct In and above, slow cooled to room temperature, contained dark etching second phase particles situated both in the matrix and grain boundaries of the a-grains, see Figs. 2 and 3. These particles were identified to be unalloyed indium by X-ray diffraction. The lattice parameter of the a phase reached a maximum of 2.8672A at the indium level of -0.28 at. pct. The present diagram, Fig. 1, is in substantial agreement with that of Stadelmaier and Fiedler' except for certain differences in detail. For example, they found the monotectic composition and temperature to be 7.0 at. pct In and 1443oC, respectively, while the present work indicates them to be 3.4 at. pct In and 1470°C. The 6 + L2/y + L2 transformation is indicated in the present work to occur at -1350°C, whereas Stadelmaier and Fiedler find this to occur at -1320°C. They also claim that the width of the y field is 0.2 at. pct In while the present work shows the width to be between 0.4 and 0.5 at. pct In. 1) Indium, when alloyed with iron, gives rise to a restricted y field, the width being >0.5 at. pct In.

Jan 1, 1970

The Pueblo Viejo Mine, a 7, 250 mtpd (8,000 stpd) gold-silver cyanidation plant built by Rosario Dominicana S. A., was described in Volume I of this monograph. At the time of writing that volume, Pueblo Viejo had not yet gone on-stream and operating data or costs could not be presented. Since that time this information has been obtained and several interesting modifications and an expansion have been made to the plant. Because Pueblo Viejo is the largest open-pit gold mine in the world and one of the world's leading gold-silver operations with production of approximately 31 kg (1,000 oz) gold and 125 to 155 kg (4,000 to 5, 000 oz) silver per day, the authors have updated the previous data and flow sheet. The Dominican Government, which held a 4670 interest in Rosario Dominicana S. A., completed purchase of the mine to gain full control in 1979. Rosario Resources will continue to manage the mine, at least until the end of 1980. Gold was produced at Pueblo Viejo almost 500 years ago with initial production in the year 1505. Rosario Resources became interested in the property in 1969 and found surface oxidation had rendered the upper portion of the ore body amenable to direct cyanide treatment. The treatment of the underlying gold-bearing sulfide zone is still undergoing metallurgical studies. The ore is considered to be a laterite; and because there appeared to be few boulders in the ore zone, only a 400 m (16 in. ) square grizzly was initially installed ahead of the mills when the plant went on-stream in late 1974 at a design capacity of 7,250 mtpd (8,000 stpd). Operation also proved the ore to be harder than was originally anticipated. During 1967 a 1. 25 m by 1. 5 m (48 in. by 60 in. ) jaw crusher was installed to -feed the 1, 000 mt (1, 100 st) mill bin. Minus 200 mm (8 in.) crushed ore is fed directly to two 5.5 m by 1. 8 m (18 ft by 6 ft) semi-autogenous mills re-powered with 750 km (1,000 hp) motors and 50 mm (2 in.) grates. Each mill product is screened at 13 mm (1 /2 in.) by a vibrating screen. Screen oversize from each mill is combined on a single return belt equipped with a magnetic head pulley for grinding ball removal. The non-magnetic oversize is then split into two fractions for return to the primary mills. Originally, a minus 6 mm (1/4 in ) product was made on each screen and fed to a 300 kw (400 hp) 2.6 m by 3. 7 m (8-1/2 ft by 12 ft) regrind mill. During a plant expansion in 1978, an intermediate mill of 746 kw (1,000 hp) was installed to operate in open circuit on the combined primary mill

Jan 1, 1981

By John T. Galey

An intensified search for gas, because of the shortage in the area, led to the completion of 482 wells in southwestern Pennsylvania during 1944. This number was 27 more than the number in 1943, but 118 of the wells were nonproductive. Shallow Development Oil The initial production of the 25 producers completed was slightly less than was obtained from four wells above last yearJs total. The largest well, 20 bbl., was found in the Big Injun (Miss.) sand in Morris township, Washington County, at a depth of 2085 ft. It is currently producing about 3 bbl. per day. Outside the main producing area, a well drilled in Nicholson township, Fayette County, obtained 15 bbl. per day from 1864 to 1866 ft. in the Gantz (U. Dev.) sand. The Federal subsidy of 75¢ per barrel, effective , 1, 1944, which increased to $3.40 the current pipe-line price in this area, seems to have been insufficient stimulus to materially increase drilling for oil, although more repressuring operations are contemplated. Gas The volume of initial open flow of gas developed is off slightly over 10 million cu. ft. from 36 more wells than were completed a year ago, and the average rock pressure of this new gas is more than 100 lb. less than that obtained a year ago. Apparently the best find of this year was reported in Patton township, Allegheny County, where an initial volume of over 4 million cu. ft, was encountered in the Speechley (U. Dev.) sand at a depth of from 3293 to 3303 ft. The rock pressure there, 1190 lb. per sq. in., is nearly virgin. However, this area is fairly well delimited by dry holes and docs not seem nearly so promising from the standpoint of reserves as the Armbrust area, which was discovered several Years ago. In the patton township locality another fair well with 1303 M cu. ft. open flow and 400 lb. Per 59. in. rock pressure completed in the Hundred-Foot (U. Dev.) sand at a a depth of 2125 feet. Armstrong County, as usual, leads in number of producing wells completed with lowest percentage of failures but ranks only fou th in volume of production developed. Only two wells here had more than one million cubic feet capacity, but the rock pessure was under 200 Ib. Per sq. inch. In Fayette County, where the largest portion of new gas was found, activity appears to be shifting eastward. In Luzerne township, four producers having a total combined initial open flow in excess of 10 million cu, ft, were found in the Big Injun (Miss.) sand. The best well was found also in the same area in the Speechley sand (U. Dev.) at a depth of 3460 ft. This was a 2500-M CU. ft. well in Georges township. Several wells of more than a million cubic feet capacity were found in Jackson, Washington, Wayne and Whitley townships, Greene County. None of these, however, was in a new pool.

Jan 1, 1945

By C. W. Donnelly, Louise B. Freeman, Coleman D. Hunter

It is with pride that the authors of this paper report. that during 1944 the production of petroleum in Kentucky passed its all-time peak, 9,496,985 bbl. being contributed. The delivery of natural gas, especially from eastern Kentucky, was maintained and possibly exceeded the highest deliveries of the past. To raise the production of oil and gas was not easy with inferior and worn-out equipment and the shortage of skilled labor. Reminiscent of the early days of the industry in the state, particularly in the hills of Elliott County, where mud roads often have gradients of 45º, was the replacement of worn-out trucks and tractors by oxen. Of the total 9,496,985 bbl., 17 per cent was contributed by the part of Kentucky that is east of the Cincinnati arch, as compared with the total of 7,010,776 bbl. contributed in 1943, of which 25 per cent was contributed by eastern Kentucky. This discrepancy is due to the discovery of more new fields in western Kentucky rather than to a decrease in production in the eastern fields, where the average has been maintained by reconditioning and secondary recovery of old fields and further development of new pools reported for the first time in 1943. In all, 1103 wells were known to have been drilled in the state during 1944, of which 659 were drilled in western Kentucky and 444 in eastern Kentucky. The exact number of wells drilled for any year is never known, as drilling permits are not required except 'when it is planned to drill through a workable coal seam. Of the total number of wells drilled, 459 were oil wells, 229 gas wells and 415 dry holes. The monthly production was as follows: January........................... 659,496 February.......................... 658,606 March...................... ...... 711,619 April............................. 649,926 May............................... 754,892 June.............................. 730,369 July.............................. 761,762 August............................ 878,053 September...................... 863,150 October........................... 968,732 November........................ 961,999 December........................ . 898,636 Western Kentucky In western Kentucky 352 wells were completed as oil wells with a total initial production of 47,922 bbl. of oil, the average being 136 bbl. per well. Two wells produced gas, the total initial production being 1,594,000 cu, ft. One hundred and eighteon wildcat wells were drilled, of which 107 were dry holes and 11 were oil wells. Three of the latter proved to be the discovery wells of commercial pools. Twelve new pools were discovered during 1944, none of major importance, as indicated in Table 2. The Utley pool, due to a stratigraphic trap on the flank of a closed structure, found oil in the Mcclosky at 2565 ft. in the discovery well, with initial productioil of 1000 bbl. The average daily production is now 227 bbl. from seven wells. The East Poole field, with the discovery well in the Tar Springs sandstone at 1811

Jan 1, 1945

By W. R. Aufricht, E. H. Koepf

The theory, measurement, and application of capillary forces in reservoir rock have been treated ex-tensively in the various petroleum publications.1,2,3,4 These forces are of prime importance in oil production, and data on capillary properties are among the most important tools used in the study of reservoir mechanics. The principal application of measured capillary pressure data by the production and reservoir engineer is in the determination of the initial distribution and mobility of fluids in the reservoir. The distribution refers to the magnitude of the oil and interstitial water saturations under capillary equilibrium conditions and to their variation throughout the reservoir as a result of changes in rock properties and nearness to free water. The magnitude of the water (or oil) saturation, as well as the porosity, is required in volumetric calculations of oil in place. In low permeability reservoirs, where long transition zones are common, the magnitude of the oil content, even below the depth interval where commercial rates of flow of oil can be obtained, must be evaluated since this oil contains energy available to the production of the remainder of the reservoir. The mobility of the water phase is of particular importance in water-flood calculations since mobile water may condemn what would otherwise be a successful water flood. In reservoirs with predominantly small pores, high immobile water contents are possible. Conversely, reservoirs with predominantly large pores may contain mobile water even though the interstitial water contents are relatively low. This presentation reviews the distribution and mobility of interstitial water contents as determined from capillary pressure data and shows typical data for various types of carbonate reservoirs. A discussion of the variations found in different types of carbonate reservoirs is given. DISCUSSION Interpretation of Laboratory Data Fig. 1 is a typical laboratory capillary Pressure curve where water saturation as Per cent of Pore space is plotted vs capillary Pressure (psig) for an air-water system. This par- ticular curve was obtained by measurement on a sample of San Andres dolomite with intergranular-type porosity. The sample studied had a permeability of 10.0 md and a porosity of 18.8 per cent. The capillary pressure-saturation relationship illustrated is an inherent property of the rock (a function of the size and distribution of the pores) and represents the ability of this water-wet rock to retain water against the pressure differential exerted by a non-wetting fluid (oil or gas) to remove it. In the laboratory a known pressure differential is exerted from a pressure source; in the reservoir the pressure differential is controlled by the density difference between the hvdrocarbons and the water. The laboratory capillary pressure values may be converted into terms of equivalent height of water column using known values of reservoir oil and water density and measured or average values of interfacial tension

Jan 1, 1958

By William H. Spice

The fault zone of south central Texas showed renewed activity during I940 along a trend roughly paralleling the old established Balcones fault-line group of producing fields. This was a result of the new discoveries in the Wilcox (Eocene) formation in southeastern Texas and Louisiana. As of the end of the year, one new field producing from the Wilcox formation had been discovered on the Washburn ranch in La Salle County, along the southwestern limits of the district, and several projected tests into that formation were under way. In the western part of the district, par-titularly in the part of the Rio Grande embayment that is in Dimmit, Webb and Zavala Counties, there has been renewed leasing activity with the shallower sands in the Navarro-Taylor formations (Upper Cretaceous) as the objective in several projected tests for the early part of 1941. Three new fields have been discovered along the old fault-line trend, but these have been comparatively small, producing either from Dale lime, Austin chalk or Buda lime. No new fields were discovered during the Year in the Edwards (Lower Cretaceous) lime horizon. Approximately 260 wells were drilled in the district during 1940, which resulted in four new oil fields. Twenty-seven new wells were completed in the Proven Edwards lime fields of Darst Creek, Luling and Salt Flat and seven were added to production in the Pearsall field. Approximately 160 wells in 18 counties were completed as failures during the year. The district produced 7,659,634 bbl. during 1940, which was a 9 per cent decrease under production for 1939. In all, 3559 wells were producing at the end of I940, compared with 3562 wells producing at the end of the previous year; 104 new producing wells were completed and 163 wells were abandoned in the producing fields of the district. During 1940 considerable exploratory work was carried on along the Wilcox trend within the district, particularly by major companies employing various types of geophysical methods, and leasing activity increased considerably. At the end of the year, the total number of acres of nonproducing leases held by major companies in the district increased about 10 per cent. It is anticipated that this activity will continue into the first part of 1941 and will be supplemented by several exploratory test wells. New Fields B,, Creek, Caldwett County.— . R. Ogden NO. 2 Talley, discovery well of the Bee Creek field, in the northeastern part of Caldwell County, was completed on March 16, I940, in Dale lime from 2091 to 2238 ft., pumping 85 bbl. per day, 39° A.P.1. gravity. The discovery of this field can be credited to a combination of subsurface geology and magnetometer work, which indicated the presence of a serpentine intrusion. At the end of the year, ,3 producing oil wells had been completed and the field has produced a total of 47,050 barrels.

Jan 1, 1941

By John Wulff

IN a previous paper Burwell and Wulff1 have shown by electron diffraction studies that allotropic transformations can be induced in 18-8 stainless steel by polishing to a depth of about 5 X 10-5 cm. The development of a successful etching technique, which removes accountable amounts of metal from the surface without pitting and without changing the root-mean-square profile as measured with an Abbot profilometer, led to the application of the whole technique and material to an investigation of various mechanical methods of surface preparation, such as grinding, lapping, superfinishing and cold-rolling. Ideally suited to such a study is 18-8 of low carbon and nitrogen content. The material can be heat-treated to produce a coarse-grained single-phase structure. On cold deformation there occurs not only a reduction in grain size but, at regions of maximum stress, a change of face-centered material to body-centered material, provided the metal is worked below about 200°C. When worked between 200° and 415°C., diffraction studies evidence a reduction in grain size without the appearance of any new body-centered ferrite. Ferrite, which can be referred also to strains induced by carbide precipitation, is evident when the material is worked at temperatures between 415° and 800°C. Stainless steel is advantageous because the usual surface-finishing operations do not readily oxidize it to any appreciable depth. In order to produce detectable oxide films on the surface of austenitic 18-8 in a time equivalent to that required to produce, for example, a fine ground finish on ½ sq. in., the sample must be held in a furnace or oxygen stream above 600°C. By using longer heating times, it is possible to achieve measurable oxide films on samples whose surface temperatures exceed only about 250°C. EXPERIMENTAL PROCEDURE The apparatus, material, and technique described in the previous paper1 were employed in this investigation. Samples of 18-8, 1 by 1 cm. by 4 mm., were carefully annealed in the austenitic range to produce a coarse-grained structure. They were then quenched and pickled to remove scale. On a lapping machine of the Graton2 type, both sides of each sample were polished to a flatness of 1/6 a wave length of sodium D light. Thereafter they were electrolytically etched to remove at least 1 X 10-3 cm. of the surface, a depth that is well below that of any deformations induced by surface preparation. Samples of this material, carefully mounted in steel holders, were then sent to various industrial organizations known for special finishing techniques. In the instrument shops at the Massachusetts Institute of Technology check samples were finished by the same methods, as far as they were available. Abbot profilometer3 readings were made on all the samples, which were then carefully degreased in double distilled benzine and alcohol, dried in a hot-filtered air blast, and kept in a desiccator. Suc-

Jan 1, 1941

By Louis A. Panek

THE purpose of this paper is to present a method of designing safe and economical arch structures that are to be constructed of concrete or directly of original earth materials. The experimental data used to illustrate the design method are taken from Bucky and Fentress,1,2 and the application of the ideas presented by them is extended by obtaining an additional set of curves from which arch structures may be designed. This design method is based upon the following principles of similitude: A scalar model made of the same material as that of the full sized structure will behave similarly to its prototype if the density of the model is increased in the same proportion as its linear scale is decreased. Let R represent the scale or model ratio, namely, the ratio of a prototype linear dimension to the corresponding model linear dimension. The effect of increased density may be obtained by rotating the model in a centrifuge at a speed such that the centrifugal field exerts on the model an accelerative force R times the accelerative force of gravity. Under these conditions; (I) model unit stresses are equal to corresponding prototype unit stresses, (2) the ratio of the prototype deformation at a given point to the model deformation at a similar point is equal to the scale ratio, R, and (3) the model and the prototype will behave similarly within and beyond the elastic limits of strain. According to the above relations, such models can be used to solve the following problems: I. The dimensions of the most economical safe arch structure for a given load. 2. The maximum safe roof span underground for given geologic conditions. The procedure is described briefly as follows. Tests are made by rotating in a centrifuge a number of models that repIesent a variety of prototype loads and dimensions. From the experimental data, curves are plotted to show the relations between these loads and dimensions. The curves are used to solve directly the problems stated above. Structural design is based upon the working (safe) stress of the material of construction, which is established by applying a factor of safety to the experimentally determined ultimate strength of the material. In conformity with this principle, each model is gradually loaded until failure occurs. A safety factor is then applied to the results. If a safety factor of 4 is used, a given model at failure represents a safe prototype, the linear dimensions of which are equal to one-fourth the model ratio at failure times the corresponding model dimensions. The safe model ratio is computed from the following formula: [Safe R = (rl 47r2n2r _ 7r2n2r~r~ \4/ gg in which: n = centrifuge revolutions per second at model failure; r = radius of rotation of the model in feet; g = 32.2 ft/sect.]

Jan 1, 1947

By R. S. Shoemaker, F. W. McQuiston

The principle of cyanide recovery or regeneration of cyanide from solution, be it a weak wash or a foul solution, is by acidulation. All or part of the cyanogen is converted thereby into hydrogen cyanide which is fixed by an alkali (generally lime) and returned to the cyaniding system (the Mills- Crowe process). The solution is made acid by bringing it into contact with sulfur dioxide. The acidified solution is stripped in a packed tower by a counter flow stream of air in which the air and the solution are brought into intimate contact. The air leaving the tank charged with hydrogen cyanide is then passed to another tank in which it is mixed with an alkaline solution, the latter absorbing the HCN and leaving the accompanying air clean for reuse in removing more HCN from the acidified solutions. Of the recoverable cyanide, 9770 is usually recovered in a three-unit disperser tower system. When there is a considerable content of copper, the solution is made acid following standard procedure; however, the HCN is not removed until the copper is reduced by regeneration. Copper removal at this point may be as high as 90%. After reduction of the copper, the acidified solution then is contacted with a lime solution which brings down calcium sulfate as a second step. The silver, gold, and copper are recovered in the form of a precipitate which can be shipped to a smelter. At the Hudson Bay Mining and Smelting Company, Ltd., most of the precious metals have been recovered in the copper and lead concentrates, but it has been found profitable to submit the flotation tailings to a scavenger cyanide treatment for the recovery of exposed gold contained in pyrite rejected during flotation. Due to the fine particle size, maximum dissolution is achieved in a four-hour contact period. In the cyanidation plant, the thickened flotation tailing at 70% solids is given a four-hour agitation in weak calcium cyanide solution and filtered. Filter cake is repulped and discharged either to the tailing storage area or to the mine as backfill. Clarification, de-aeration and precipitation of pregnant solutions are carried out in a standard Merrill-Crowe unit. Typical analysis of precipitate is as follows: Au, 0.47%, Ag, 4. 88%; Cu, 46.0%; Zn, 13. 8%. Cyanicides in the form of copper minerals limit the reuse of barren solution. To recover the substantial quantities of cyanogen chemically combined with base metals in this solution, a cyanide regeneration plant is in operation. The barren solution is acidified with sulfuric acid in a spray tower where an upward current of air from a blower sweeps the liberated hydrocyanic acid gas to an adsorption unit where it meets a fine rain of lime suspended in plant solution with which it combines to form calcium cyanide. The lime--water solution carrying calcium cyanide is reused in the cyanide circuit. The return gases are drawn into the blower and back to the disperser tower thus

Jan 1, 1975

The Jeffrey operation of Canadian Johns -Manville Co. , Ltd., at Asbestos, Quebec, is considered to be the world's largest asbestos mine. It accounts for approximately 37% of Canadian production of chysotile asbestos and about 13% of world production. Rated capacity is over 600,000 stpy (540,000 mtpy) of fiber, of which well over 90% is exported to the United States and seventy other countries. During the early 1970's the company completed a five-year modernization and expansion program which included the installation of a unique 72 in. by 93 in. gyratory crusher to handle the extremely blocky serpentinized peridotite ore. Because of the large diameter of this crusher the top ring of the shell was made in two halves which were bolted together. Hundred-ton trucks dump from two sides of the crusher into the 200 st (180 mt) dump pocket which is equipped with dust collecting ducts in the walls of the other two sides. The installation was designed to accommodate the eventual use of 200 -ton trucks. Crushed ore at a. size of 7 ½ in. (191 mm) falls into a uniquely designed crushed ore pocket equipped with three sloping steel sides and one vertical side, which make it totally live. Infrared heaters installed in back of the hopper sides prevent the ore from sticking to the steel. Another interesting feature is an eccentric removal bridge which is permanently mounted inside the crushed ore pocket. The two halves of the bridge are let down by electric winches to form a platform on which the eccentric cart travels and from where maintenance is done. Level indications in the crushed ore pocket are by radioactive indicators. Under the crushed ore pocket is a 72 in. by 28 ft (1.83 m by 8.5 m) apron feeder which operates at 7. 2 to 50 fpm (2. 3 to 15. 3 mpm). Crushed ore is discharged to a picking belt for tramp removal. A crossbelt magnetic separator is also mounted over this belt. Permanently mounted belt reels are also situated over the picking belt to facilitate the changing of this unit. A 60 in. (1. 52 m) wide takeaway belt then elevates the crushed ore to t.he surface facilities. Instead of discharging to a crushed ore stockpile, the takeaway conveyor delivers the ore to a 300-ton distribution bin. The ore is then screened and secondary crushed; and the plus ¾ in. (19 m) is "stored in a 3,000 ton bin while the minus ¾ in. is dried and then sent to storage. This system of directly screening primary crushed ore is similar to that used at both the Endako molybdenum and Gibraltar copper operations in British Columbia. While it would seem connecting processing equipment directly to a primary crusher would have an adverse effect on the crusher availability, the 94% of scheduled time this crusher

Jan 1, 1978

By William H. Spice

The area on which oil and gas development is reported covers 30 counties, which are included in the Texas Railroad Commission's District No. I. This area not only includes the old established Balcones fault-line group of producing fields but also includes the southwest extension of this trend and some of the deeper Wilcox (Eocene) exploratory development. (Fig. J.) In the old Balcones fault-line zone, three new fields were discovered during 1941. These fields are comparatively small, producing from Dale limestone or Austin chalk. No new fields were discovered during the year in the Edwards (Lower Cretaceous) limestone horizon. One new shallow field was discovered in the Reklaw (Eocene) sand horizon and, in the southwestern part of the district, one oil field and one gas field were discovered in the Navarro (Upper Cretaceous) sand horizon. An extremely important extension was made to the one producing Wilcox (Eocene) field of the district in the Washburn Ranch field of La Salle County. The district produced 6,650,357 bbl. during 1941, which was a 12 per cent decrease under production for 1940. Approximately 4,954,000 bbl. of this total production was produced by the three Edwards limestone fields, Luling, Salt Flat and Darst Creek, the remaining production coming from the other 43 active fields in the district. In all, 3694 wells were producing at the end of 1941, compared with 3559 wells at the end of the previous year. During the year, 139 new producing wells were completed and 29 wells were abandoned in the producing fields. The increase in producing wells represents an increase in new wells over abandonments in these fields, together with a decrease in wells temporarily shut down as of the end of 1941. The majority of production drilling was carried on in the following fields; Bee Creek, Chicon Lake, Elm Creek, Gas Ridge, Pearsall and Tenney Creek. Approximately 250 wells were drilled during 1941, of which 110 were exploratory wells completed as failures throughout the district. Considerable exploratory work was continued during 1941 along the Wilcox trend. Geophysical work employing various types of geophysical methods and leasing activity was continued along this trend, particularly by the major companies. The significance of this activity is apparent from the successful extension and development in the Washburn field of La Salle County, where several well-developed gas-and-oil producing horizons have been developed in the lower Wilcox section between 5100 and 5600 ft. as noted in the following paragraphs. Continued exploratory activity along this general trend as far as present conditions will permit is predicted for 1942. New Fields Elgin Field, Bastrop County.—No. I-A Hiram Walker, Marts and Beaven, Inc., discovery well of the Elgin field, was com pleted on Apr. 22, 1941, in broken Austin chalk from 2820 to 2840 ft., pumping 105 bbl. per day, 36.8°A.P.I. gravity. The well apparently is producing from a crevice in

Jan 1, 1942

By J. T. Norton, J. G. McMullin

An 1820°C isothermal cross section of the Ti-Ta-C ternary diagram was prepared from X-ray diffraction and metallographic data. No phases other than those appearing in the three binary diagrams were observed. At temperatures above the titanium transition temperature titanium and tantalum form a complete series of solid solutions containing up to 2 atomic pct C. The phases Tic and TaC also form a continuous series of solid solutions extending across the diagram. PREVIOUS work on this alloy system was very limited. Of the three binary constitution diagrams involved, only one, the Ta-C system was available in the literature. Preliminary data on the other two systems was received from the investigators during the course of the investigation and both have been published in recent months. It had been shown that Tic and TaC formed a continuous series of solid solutions, but the range of carbon content in this phase was not known. While Ta2C had been described, its solubility for or reactions with other carbides had not been reported. It was not known whether or not any ternary compounds occurred in the system. The present program was undertaken to determine experimentally the general form of the ternary diagram. It is hoped that the results will be of value in furthering the development of sintered carbide cutting materials and high temperature ceramets, many of which contain combinations of Tic and TaC. The Binary Systems Of the three binary diagrams involved only that of Ta-C was available at the time this project was started. The diagram of Ellinger¹ redrawn in Fig. 1, shows a hexagonal phase Ta2C having a very small composition range and a cubic TaC phase having a composition range of from 40 to 50 atomic pct C. The authors made a separate determination of the composition range of TaC using lattice constant values and found the range to extend from 40 to 49.7 atomic pct C in good agreement with Ellinger's diagram. Two determinations of the Ti-Ta system have appeared recently.2,3 These two diagrams are in good agreement and show that ß titanium and tantalum form a complete series of solid solutions. The Ti-C diagram by Cadoff and Nielsen4 shows a very limited solubility of carbon in both a and ß titanium. The single carbide formed persists over a wide range of carbon contents. Several values for the upper limit of carbon content of this phase have been reported."' The highest value obtained in the M.I.T. Laboratory was 47.5 atomic pct C with a lattice constant of 4.328?.5 Fattinger7 describes a gas carburization method which he claims produces stoichiometric Tic although he does not present any data showing that he actually had 50 atomic pct combined carbon. Several complete analyses on

Jan 1, 1954