Search Documents

By H. O. Hofman

WHEN dry chlorine gas is made to act in the cold upon finely¬divided gold,' it converts the latter with evolution of heat into auro-auric chloride, Au2CI4, a hard, dark-red, hygroscopic salt. Moisture splits this salt into aurous and aerie chloride, Au2C14 = AuCI + AuCI3; treatment with water converts it into auric chloride and gold, 3 Au2CI4 = 4 AuC13 + Au,. Aurous chloride, when stirred with water, undergoes a similar decomposition, 3 AuCI = AuCI3 + Au,. These decompositions of auro-auric chloride and of aurous chloride furnish the explanation for the practice of moistening an ore before it is treated by the Plattner chlorination-process; practical experience having shown that gaseous chlorine gave an unsatisfactory extraction with dry ore. According to Rose,' fine gold is acted upon more slowly by chlorine than gold containing some base metal, e.g., copper. He also states that small quantities of silver increase the rate of solution, but adds that the coating of silver chloride formed checks, and finally stops, further action, if the percentage of silver be increased beyond a certain undetermined amount. Bromine' acts upon finely-divided gold in a manner similar to chlorine; the auro-auric bromide, Au2Br4, however, is not hygroscopic. Upon treatment with water it is decomposed as is the corresponding chlorine salt. It is generally believed that bromine does not act as energetically upon gold as does chlorine. This seems to be borne out by the results in the leach-

Mar 1, 1905

By F. G. Cottrell

(New York Meeting, February, 1912.) ABOUT a year and a half ago, at the San Francisco meeting of the American Chemical Society, in connection with the excursions to local smelting-works, I had occasion to show some lantern-slides illustrating the recent commercial development of electrical methods for precipitating the suspended matter from smelter-smoke, the underlying phenomena of which were clearly brought to the attention of the technical public by Sir Oliver Lodge as long ago as 1884. In the Journal of industrial and Engineering Chemistry, August, 1911, most of these views were reproduced, together with an account of the work from its beginning up to July, 1911. To-day I wish particularly to show you some of the further developments of the work since that time; but in order to make these clear they will be prefaced by a brief abstract of the article above referred to. The removal of suspended particles, front gases, by the aid of electric discharges is by no means a new idea. As early as 1824 we' find it suggested by Hohlfeld 1 as a means of suppressing ordinary smoke, and again a quarter of a, century later by Guitard.2 These suggestions, which do not seem to have stimulated any practical study of the question, were soon entirely forgotten, and only brought to light again by Sir Oliver Lodge,3 many years after he himself had independently rediscovered the same phenomena and brought them to public attention 4 in a lecture before the Liverpool Section of the So-

Jul 1, 1912

Jan 1, 1893

By John T. Cumberlidge, Frederic M. Chace

Nickel-bearing saprolite developed during the early Tertiary over a northeast trending ultramafic body of Jurassic age near Riddle in southwestern Oregon. The principal nickel mineral is garnierite, but other complex nickel minerals may be present. There are two main ore bodies, an upper (older) one associated with the Klamath peneplain, and a lower (younger) one on the Sherwood peneplain. Saprolite constitutes the bulk of the ore and was probably derived from peridotite and dunite through chemical decomposition by downward percolating meteoric groundwater. Decomposition took place by net loss of MgO, SiO2, and Fe without a change in volume. Faults and joints provided permeable zones which localized saprolite development, and faulting may have helped preserve some ore from loss by erosion. Garnierite-chalcedony boxwork ore was deposited by meteoric groundwater along faults, joints, and at the level of former water tables. Boxwork ore is entirely supergene, the chemical constituents having been derived from higher in the soil profile. The saprolites show evidence of both supergene and residual enrichment in nickel. Red and yellow soil occurs as a capping over saprolite and boxwork, and was derived from them by chemical and mechanical decomposition. The present deposits are probably truncated remnants of a formerly thicker and much more extensive deposit which probably included laterite at the surface. The deposits started to form in the early Tertiary due to deep chemical weathering under sub-tropical to warmtemperature conditions. Early Tertiary ero~ion surfaces of low relief probably contributed to the predominance of chemical weathering over mechanical erosion. Alteration under present climatic conditions favors the formation of soil from saprolite rather than the formation of new saprolite from peridotite.

Jan 1, 1968

By Fleming, R. C.

ONE OF THE NEWEST developments of industry rising from the commercial application of scientific knowledge is in the making of solid carbon dioxide from the gas about 1925 the first efforts were made to manufacture "dry ice" on a large scale and at a price to permit widespread use. From that beginning the industry has grown to a consumption of 40,000 tons in 1930. Carbon-dioxide ice, as the name implies, is merely the gas compressed and cooled to a solid. The ice has a temperature of 109° F. below zero and is in many ways superior to water ice. It evaporates to a gaseous form so it is not wet and leaves no trace; in fact, one suggested minor use is as coasters under water glasses on the dining table. The gas is harmless except in large concentrations and. when the ice is used as a refrigerant, the resulting gas actually becomes a preservative, keeping oxygen away from perishable products. Not only does the ice have a greater amount of cold in a small volume than water ice but cooling is effected by direct contact of the resulting gas with the materials to be refrigerated rather than by convection air currents.

Jan 1, 1932

By Felix A. Vogel

I (New York Meeting, February, 1912.) FLUE-DUST, to most blast-furnace operators, means a troublesome by-product, the formation of which should be curtailed, if not prevented entirely. However, with the increasing use of fine ores, larger furnaces, and high-pressure blast, the production of flue-dust is constantly increasing, and amounts annually in the United States to from 3,000,000 to 3,500,000 tons, An exceedingly high tonnage, of which a large part has been discarded as valueless. As a result of greater economy in the iron industry, the attention of our furnace-men has been directed towards the utilization of this enormous amount of waste material, a problem which had also been given due consideration by metallurgists abroad. Flue-dust is generally a fine material containing considerable coke and iron-ore, with a small admixture of lime and silica, depending upon the burden. The iron-ore is partly reduced, which shows that the dust originates largely in the reducing-zone of the blast-furnace. In the United States this dust usually contains 20 per cent. of coke and more than 40 per cent. of iron. Estimating coke to be worth $3.25 per ton, and iron-ore 7 cents per unit, a ton of flue-dust, unless made available, represents a loss to the furnace-man of $3.50. This accounts for the first efforts to recharge the flue-dust into the furnace, either by moistening it clown with an excess of water, or mixing it with clay to form balls of pulp, or treating it with lime-water. These methods, however, have been practically discarded, as they failed to produce the desired economies. To recover, in the blast-furnace, all the values represented by the material contained in the flue-dust, the following con¬ditions should be complied with

May 1, 1912

By William R. Rumbold

THE Kinta valley in the State of Perak, one of the largest of the Federated Malay States, is probably at the present time the richest alluvial tin-district in the world, Perak producing from 20,000 to 25,000 tons of tin annually, and the Kiuta valley being the chief producer. The valley runs approximately north and south, and is 30 miles long by 12 wide. It is very flat, the mountain-ranges on either side rising abruptly from the plain, that on the east being the great Central range of the peninsula, and that on the west a subsidiary range marked " Kledang " on the map, Fig. 1. The valley is drained by the Kinta river, which rises in the eastern mountain range and flows south to join the Perak river, being joined by numerous streams from both mountain-ranges. The rain-fall is heavy, averaging annually about 90 in. The whole country is covered with dense jungle, except where it has been cleared for mining-operations and a small amount of cultivation. Mining villages are scattered throughout the valley, the chief towns being Kampar, Batu Gajah, Lahat and Ipoh, the latter being the center of the mining-operations. An ideal section of the main geological features of the Kinta valley is given in Fig. 2. The valley is composed of a highly crystalline limestone, usually white in color, sometimes gray; in fact, it may be called marble. It is always highly inclined and often contorted, and in some places is interbedded with shale. On the east side of the valley, near its contact with the granite, it forms a remarkable series of limestone cliffs, which rise in some cases as high as 2,000 ft. above the level of the limestone in the valley. It is non-fossiliferous, and its geo-

Sep 1, 1906

By Carl Scholz

DURING November And December, 1907, Four Serious Mine-explosions Occurred In The Appalachian Coal-Field, Which Resulted In The Loss Of Nearly A Thousand Lives And Caused An Enormous . Damage To Property. These Accidents Attracted More Than The Usual Attention; Coal-Trade And Engineering Papers Contained Many Comments And Suggestions On The Cause And Prevention Of Accidents; The Daily Press In Many Instances Condemned The Coal-Operators And Charged These Accidents To Their Negligence, Or Their Anxiety To Make Money Without Adopting Precautionary Measures. Immediately After Each Accident The Respective State ..Authorities Ordered Close Investigations To Be Made, With The View Of Establishing The Cause And Suggesting Remedies To Prevent Recurrence. Representatives Of The Technologic Branch Of The U. S. Geological Survey, To Whom The Investigation Of Mine-Accidents Had Recently Been Delegated By The Secretary Of The Interior,. Visited The Mines And Co-Operated With The Local Authorities In Their Determinations. It May Be Safe To Say Here That An Investigation Of A Mine After An Explosion Has Occurred Discloses But Little, Because. The Causes Have Been Removed And Conditions Have Been Entirely Changed. On Jan. 8, 1905, The Coal-Operators Of West Virginia Organized An Association At Washington For The Purpose Of Making Extensive Investigations, And Sufficient Funds Were Pledged To Carry Out This Work. At This Organization Meeting, The Representatives Of The Geological Survey Present Had No Suggestions To Offer As To The Cause Of These Accidents. An Examination Of The Various Reports Concerning These Accidents Indicates That The Explosions Were Caused By The Ignition Of Gas Or Dust; They Show The Point Of Origin And The Direction In Which The Force Was Expended, And Give A Detailed Description Of The Damage Done. Very Little Has Been Said As To What

Jan 7, 1908

By H. E. Stauss, E. I. Salkovitz, F. W. von Batchelder

EXISTING information regarding the structure of a spherulite in nodular cast iron is based on optical studies. According to these data, a nodule consists of an aggregate of graphite crystallites radiating from the center, with the closely packed basal planes at right angles to the radii. The c axes lie along the radii. This view faces some uncertainty in the fact that the c axis does not represent the accepted direction of fastest growth in graphite. To supplement the optical information, X-ray studies have now been made. The principle used was to screen the nodule in greater part from the X-ray beam and expose only a minor cap. As successively larger portions of the nodule were introduced into the X-ray beam, any differences in the X-ray patterns could be observed. Such photographs have been taken with chromium radiation and a Laue camera. The graphite nodule itself, about 0.010 to 0.025 in. in diam, was mounted with vaseline on a micrometer screw for control of the linear motion. The nodule rotated about 45" each time that it was translated linearly. The nodules were obtained from magnesium-treated hypereutectic iron by electrolytic solution of the iron in hydrochloric acid. In Fig. la is shown the pattern of the thinnest cap examined. In Fig. lb is shown the pattern of the same nodule moved 0.003 in. farther into the X-ray beam, and rotated 45" at the same time. Figs, la and lb indicate incomplete circles for graphite (the two outer circles arise from graphite) with the side arcs much weaker than the top and bottom ones. The arcs obtained are themselves not continuous in intensity but vary with maxima of intensity some 15" and 30" apart. The structure of the nodule that would give rise to such a pattern can be explained as follows. Basically the nodule consisted of small crystallites. The discontinuous character of the diffraction rings demonstrates that the nodule was not composed of randomly oriented crystallites. The strong vertical reflections and the weak lateral reflections show that the reflecting planes were roughly normal to the radii. The absence of sharp reflection spots suggests that the nodule did not contain large crystals. The sharpness of the diffraction rings in their radial direction shows that the variations in intensity along the arcs were not the result of line broadening resulting from extremely small crystals. In the diffraction patterns two rings corresponding to graphite were found. The third and inner ring in the figures originated in the vaseline. The graphite rings correspond to the a and ß lines reflected from the basal planes, showing that the radii of the nodules are the [0001] direction normal to the basal planes of graphite. The picture of the structure that is formed is, therefore, one of aggregates of crystallites. Within each aggregate the c axes of the crystallites tend to align themselves in the radial direction of the nodule, although these axes deviate somewhat in direction by a continuous variation of angle. Correspondingly the basal planes of the graphite crystallites are generally normal to the radii. It is a pleasure to acknowledge the assistance of M. C. Bloom and R. P. Dunphy of this laboratory.

Jan 1, 1952

By H. D. Kessler, M. Hansen, R. J. Van Thyne

The phase diagram of the titanium-rich portion of the system Ti-Cr-Fe to 70 pct Ti was established by means of isothermal sections at 900°, 800°, 750°, 700°, 650°, 600°, and 550°C, using arc-cast alloys. An isotherm at 800°C was determined for the section bounded by Ti, TiFe2, and TiCr2. Micrographic analysis was employed as the principal method of investigation, supplemented by X-ray diffraction and incipient melting studies. A ternary eutectoid, ß ? a+ TiCr2 + TiFe, occurs at approximately 8 wt pct Cr, 13 wt pct Fe, and about 540°C. AMONG the first titanium-base alloys in commercial production were the Ti-Cr-Fe alloys. For this reason, the Materials Laboratory, Wright Air Development Center, sponsored an investigation of the system. No information on the constitution of the titanium-rich corner was available. Vogel and Wenderott studied titanium-poor ternary alloys.' As part of this program, the binary systems Ti-Cr and Ti-Fe have been determined previously by the authors.' Other investigators have also studied the binary systems Ti-Cr,3-7' Ti-Fe.³,8-10 Both of the binary systems are characterized by the eutectoid decomposition of the ß phase. Most of the effort of the present work has been concentrated on the titanium-rich corner with compositions of less than 30 pct total chromium and iron content. The determination of isothermal sections was the experimental approach used to obtain the ternary phase diagram. Vertical sections were used to check the consistency of the isothermal sections. While this investigation was in progress, a study of the Ti-Mo-Cr system at Armour Research Foundation disclosed the existence of a high temperature modification of TiCr2 above 1300 °C.11 This allotrope has a hexagonal structure of the MgZn2 type, iso-morphous with TiFe2, whereas the low temperature modification of TiCr2 is cubic," of the MgCu2 type. The existence of allotropy in TiCr2 of course means a more complicated set of phase relationships in this general region than if the phase were monomorphic, as was first assumed. Additional studies were made late in the investigation in order to clarify the part that the hexagonal TiCr2 phase plays in the ternary phase relationships. These will be discussed in a separate section. Because they are of greatest practical significance, the phase relationships in the titanium-rich corner will be presented first, omitting the equilibria involving the hexagonal modification of TiCr2 in an effort to simplify the presentation somewhat. Experimental Procedure Materials: The titanium used in the preparation of the alloys was iodide crystal bar (99.9 pct pure) produced by the New Jersey Zinc Co. High purity chromium and iron were obtained from the National Research Corp. Table I gives the analyses of these materials. Melting Practice: Over 100 alloy ingots weighing 10 to 20 g were melted in a nonconsumable electrode arc-melting furnace. As the techniques are identical to those reported previously,12,13 they will not be detailed here. The ingots were melted in the cavity of a copper melting block insert under a slight positive pressure of helium. No measurable hardness

Jan 1, 1954

In the special number of the magazine Ocl und Kohle (Oct. 22, 1940) dedicated to the petroleum industry of southeastern Europe, there appeared several articles relating to Yugos1avia.t In the first article the author calls attention to the fact that there are two fields in Yugoslavia that have been explored and exploited by more than 100 wells at variable depths during the last 50 years. These are on the Island of Mura, at the confluence of the Mura and the Drave. Additional exploration drilling in various other parts of the country has been without result, but certain ones of these explorations have revealed the existence of gas horizons that have some value, which are being used for industrial purposes. Table I shows the production of oil and gas between the years 1900 and 1939. TaBle —Production of Oil ad Gas in Yugoslavia . n,i Natural Natural Years oil Years Gas, Cu. Years Gas, Cu. Meters Meters T900-1929 10,000 1923 507,000 1934 1,388,000 1930 277 1924 567,000 1935 1,401,000 1931 202 I92S 691,000 I936 1,483,000 t932 289 19261 1.472,000 1937 1,841,000 1933 629 1927! 1,732,000 193s 2,431,000 1934 324 1928 2,515,000 1939 2,628,000 1935 260 1929 4,700,000 1936 137 I93O 5.345,200 1937 463 1931 6,376,153 1938 1,091 1932 1,661,737 1939 1,114 1933 959,574 The number of wells drilled from 1884 to the present time was in the neighborhood of zoo and the total footage drilled was 65,000 m. up to July I940 They may be divided roughly as follows: 12 wells in the region produce natural gas; 134 wells in the two old fields of the Island of Mura and about zo wells for the exploration of the zone of the Flysch, in Bosnia. The depths of 50 of these wells was roo to 200 m.; the depths of 50 wells oil the Island of Mura ran from zoo to 500 m.; of 2 ; wells, 500 to I000 m.; of ro wells from rooo to 2000 meters. The deepest well drilling in Yugoslavia has reached 2000 in. In the Valley of Morave, in the region of Selnica, I00 km. south of Nish, there have been discovered asphalt-bearing limestones, which contain about 15 per cent asphalt and are associated with bituminous clays. Later, at Paclenica, important deposits of natural gas were found. A zone rich in gas and oil seepages runs through Pracec, Miklenska, Bujavica, etc. The author studied these regions from the point of view of stratigraphy and tectonics. The anticlines and gas-bearing domes are concentrated in two zones: the region of the Drave (Island of Mura) and the region of the Save, southeast of zagreb, which contains the gas field in exploitation in the region of Bujavica. A full description of the productive region of the Island of Mura has been given by Egon Bohm, a geologist, in the second article mentioned. This includes a history of the exploration and exploitation that took place under Hungarian rule in this region. The most important exploration was effected between 1884 and 1885 by Stavenov and Stinger, of Vienna. In 1927 work was done in the same region by Anton Raky, a well-known explorer who makes work of this kind his specialty.

Jan 1, 1941

By John Griffen

This paper records over twenty years' experience with the use of the Rheolaveur system in the United States, showing its ability to meet changing conditions caused by the dirtier mine output of present-day mechanical mining methods. Data are given on size ranges handled, number and capacity of units installed, maintenance experience, and operating results on two-product and three-product separations. IT is not the purpose of this paper to discuss the principles employed in the Rheolaveur system of fine-coal cleaning as these have been fully covered in the technical literature of the Institute."2 Rather, our purpose will be to record the highlights of over 20 years' experience in the United States with Rheolaveur fine-coal launders, which will indicate their capabilities and costs of cleaning and their adaptability to meet the changing conditions caused by present-day mechanical mining methods. Rheolaveur fine-coal launders are used in the United States to treat a wide variety of size ranges of fine coal, the coarsest being 1/2 in. to 0 and the finest about 1/8 in. to 0. In Europe feeds as coarse as 5/8 in. and as small as 1/2 mm (28-mesh) to 0 are being cleaned. The size ranges usually handled in this country are 3/8 to 1/4-in. round to 0. Thirty five units with a combined hourly feed capacity of 3200 tph have been installed in the United States. Individual units are cleaning as little as 25 tph, while others are cleaning as much as 200 tph. Rheolaveur fine-coal launders offer cleaning units of high capacity and are outstanding in requiring a minimum of building space per ton of input. Experience has shown that maintenance costs are low. Several installations were made in the Pittsburgh district from 1928 to 1930, and since that time operation has been largely two shifts per day. Minor repairs to liner plates and Rheo boxes have been required during the intervening years, but no major replacement of launders was required until 1947 and 1948. At one of these plants, launders operated for 17 years before they were replaced and during that period over 26,000,000 tons of —5/16-in. coal were cleaned. The effect of the much dirtier raw coal produced by mechanical loading of the Pittsburgh seam is shown by the following tests. The data in table I summarize the performance of a Rheo fine-coal unit when cleaning hand-loaded raw coal. The —4-in. raw coal fed to the cleaning plant analyzed only 8.16 pct ash and 1.31 pct sulphur and contained 4.6 pct sink, 1.55 sp gr. Two years later, in 1945, mechanically-loaded coal from the same mine was cleaned in the same plant. The feed, —4 in., then analyzed 20.10 pct ash and 1.53 pct sulphur and contained 20.2 pct sink, 1.55 sp gr. The performance of the Rheo fine-coal unit when cleaning this coal is given in table 11. It will be noted that the +48-mesh coal is cleaned almost as thoroughly as in table I. The large amount of high-ash slimes produced from the dirtier feed are responsible for the higher ash of —--48-mesh washed coal in table 11. In this plant the Rheo fine-coal unit did not get the full load of refuse resulting from mechanical

Jan 1, 1951

By S. C. Sircar, D. R. Wiles

The rate has been studied of the hydrogen reduction of nickel ions in acetate -buffered solutions, using a nickel catalyst. At temperatures between 130°and 160°C, the rate is found to be proportional to the catalyst area, the nickel ion concentration, and the hydrogen pressure. The effect of hydrogen ions is to reduce the observed rate, likely by causing the reverse reaction (dissolution) to proceed. The experimental activation energy was found to be 25 kcal per mole. THE precipitation of metals and lower oxides from solution by hydrogen reduction has been quite actively investigated during the past few years.1 In the case of nickel, the kinetics of the precipitation have been studied in ammonia solution2 but extension of this study to acid solutions has not attracted much interest, largely because of the unfavorable thermodynamics at all but the lowest acidities. For example, Schaufelberger foundg that only 10 pct reduction of nickel could be effected in sulphate solutions. One kinetic study of the reduction of Ni++ has been reported by Knacke, Pawlek, and Sussmuth,4 in which the order of the reaction was found to be one in nickel ion and one-half in hydrogen pressure. No mention was made as to the part played by the nickel catalyst, or by the pH of the solution. Moreover, the activation energy reported (4 .12 kcal per mole) is so low as to lead to some question as to whether diffusion might be playing a major role in determining the kinetics. We have recently completed a study5 of the kinetics of the hydrogen precipitation of nickel from acetate-buffered acidic solutions whose results confirm and amplify those of Knacke et al. EXPERIMENTAL PROCEDURES The work was done in a high-pressure autoclavee by the usual technique of removing small samples of the solution for analysis. Nickel analysis was done colorimetrically by the dimethylglyoxime method.' The catalyst used was carbonyl nickel powder (Standard A powder of the Mond Nickel Co., Ltd.) which was found to be composed of spheres of less than 350 mesh. The surface area of the powder was determined in this laboratory by the B. E. T. method to be 1.85 sq m (m2) per g. The catalyst was added to the solution only after the proper temperature and pressure had been reached. Agitation of the baffled system was by a turbine-type impeller, rotated at speeds between 400 and 750 rpm. The reduction rate was found to be independent of the stirring rate, so it was assumed that diffusion in the liquid does not limit the rate. In typical experiments, the nickel concentration was unchanged during an induction period of variable length. The concentration then decreased sharply, and gradually levelled off to approach the final equilibrium value. In some cases, notably at high stirring rates, the nickel concentration was found to increase considerably during the induction period, and then to decrease. In all cases, the rate was determined from the slope of the tangent to the rate curve as the concentration first decreased below the initial value. This is seen in Fig. 1. The rate measurements were found to be reproducible to within about 5 and to be quite independent of the nature or duration of the induction period. The range of conditions used is given in Table I.

Jan 1, 1961

By T. L. Berger, M. C. lnman, M. F. Rose

AFTER shock loading, mechanical twinning has been observed by several authors1-4 for a variety of fcc metals and alloys. It has been shown2,3 that low stacking fault energy materials deform primarily by the formation of mechanical twins and stacking faults during dynamic loading. Further, Inman, Murr, and Rose2 have shown that a correlation exists between the average hardness and the volume percent of mechanically twinned material in stainless steel. It has been observed in nickel' that mechanical twins are produced during shock deformation if the peak pressure associated with the shock wave is greater than 350kbar. It is the purpose of this work to discuss shock-hardening mechanisms in nickel and to determine to what extent the initial condition influences the final response. The "flying plate technique" was used to generate planar shock waves with peak pressures as high as 710 kbar. The details of the technique5" have been discussed elsewhere and will not be repeated here. The material used in this study was polycrystalline nickel of 99.98 pct purity and had an initial grain size of 0.18 mm. Prior to any deformation, all samples were given a stress-relief anneal of 6 hr at 600°C in a vacuum furnace. After annealing, the initial condition of the samples was changed by cold rolling individual samples from 0 pct to a maximum of 80 pct reduction in thickness. This provided samples with controlled initial histories for shock deformation. Immediately after shock loading, the specimens were slowed and quenched by suitable arrangement of buffer material and water bath. This technique minimized specimen damage and the effects of shock heating on the samples. Since deformation twins in high stacking fault energy fcc metals are only produced at high stress levels, the initial defect configuration prior to mechanical twinning should greatly influence the number of twins formed. In fact, Zukas and Fowler7 have found that prestraining in iron and steel greatly suppresses the formation of mechanical twins during the shock deformation process. Following the methods of Warren and warekois8 and Cohen and Wagner,9 X-ray diffraction profile analysis was performed to determine the incidence of stacking faults and mechanical twins in the deformed nickel. Analysis was made on samples in the annealed, cold-rolled, shock-loaded, and cold-rolled—shock-loaded states. The estimated accuracy of the peak position measurements is *0.01 deg in 2?. Therefore the accuracy in the measurement of the relative peak shifts between the (400) and (222) diffraction line profiles is on the order of *0.04 deg in 2?. None of our measurements indicated peak shifts greater than 0.04 in 28. This would correspond to a fault density of -1 pct and sets the limit on the sensitivity of our instrument. Similarly, analysis of the shift in the center of gravity of the diffraction line profiles yields the minimum measurable value of the twin fault probabilitya to be -0.002. Fig. 1 shows mechanical twinning in nickel shock-loaded to 400 kbar. In this photograph, fault intersections are clearly visible. The thickness of the individual fault lamellae was determined from the image widths of their lines of intersections by the

Jan 1, 1968

In the special number of the magazine Ocl und Kohle (Oct. 22, 1940) dedicated to the petroleum industry of southeastern Europe, there appeared several articles relating to Yugos1avia.t In the first article the author calls attention to the fact that there are two fields in Yugoslavia that have been explored and exploited by more than 100 wells at variable depths during the last 50 years. These are on the Island of Mura, at the confluence of the Mura and the Drave. Additional exploration drilling in various other parts of the country has been without result, but certain ones of these explorations have revealed the existence of gas horizons that have some value, which are being used for industrial purposes. Table I shows the production of oil and gas between the years 1900 and 1939. TaBle —Production of Oil ad Gas in Yugoslavia . n,i Natural Natural Years oil Years Gas, Cu. Years Gas, Cu. Meters Meters T900-1929 10,000 1923 507,000 1934 1,388,000 1930 277 1924 567,000 1935 1,401,000 1931 202 I92S 691,000 I936 1,483,000 t932 289 19261 1.472,000 1937 1,841,000 1933 629 1927! 1,732,000 193s 2,431,000 1934 324 1928 2,515,000 1939 2,628,000 1935 260 1929 4,700,000 1936 137 I93O 5.345,200 1937 463 1931 6,376,153 1938 1,091 1932 1,661,737 1939 1,114 1933 959,574 The number of wells drilled from 1884 to the present time was in the neighborhood of zoo and the total footage drilled was 65,000 m. up to July I940 They may be divided roughly as follows: 12 wells in the region produce natural gas; 134 wells in the two old fields of the Island of Mura and about zo wells for the exploration of the zone of the Flysch, in Bosnia. The depths of 50 of these wells was roo to 200 m.; the depths of 50 wells oil the Island of Mura ran from zoo to 500 m.; of 2 ; wells, 500 to I000 m.; of ro wells from rooo to 2000 meters. The deepest well drilling in Yugoslavia has reached 2000 in. In the Valley of Morave, in the region of Selnica, I00 km. south of Nish, there have been discovered asphalt-bearing limestones, which contain about 15 per cent asphalt and are associated with bituminous clays. Later, at Paclenica, important deposits of natural gas were found. A zone rich in gas and oil seepages runs through Pracec, Miklenska, Bujavica, etc. The author studied these regions from the point of view of stratigraphy and tectonics. The anticlines and gas-bearing domes are concentrated in two zones: the region of the Drave (Island of Mura) and the region of the Save, southeast of zagreb, which contains the gas field in exploitation in the region of Bujavica. A full description of the productive region of the Island of Mura has been given by Egon Bohm, a geologist, in the second article mentioned. This includes a history of the exploration and exploitation that took place under Hungarian rule in this region. The most important exploration was effected between 1884 and 1885 by Stavenov and Stinger, of Vienna. In 1927 work was done in the same region by Anton Raky, a well-known explorer who makes work of this kind his specialty.

Jan 1, 1941

By Albert G. Anderson

I'm sure many of you have wondered what the term "Cross Flow Filtration" means. I shall explain it so that you more clearly understand it, and I hope you will be able to make it a useful tool for you in the future. In the simplest form of cross flow filtration contaminated fluid. or feed stream, is fed at a high velocity down the center of a porous tube, clear fluid weeps through the porous wall of the tube while the suspended solids concentrate in and are swept away by the feed stream. (See figure A). The high velocity flow of the feed stream tends to keep the inside of the tube free from a build up of contamination. By utilizing this cross flow approach to filtration, we have been able to concentrate such things as paint pigments, titanium dioxide, iron oxide, precipitated metals such as uranium yellowcake or silver, cadmium, some metal hydroxides, as well as gelatinous particles such as yeast cells. You will recognize that cross flow filtration lends itself to a recirculation loop system due to the necessity of maintaining a high velocity on the inside of the tube. This means that we generally have a storage tank from which we are recirculating, and the solids will concentrate in the storage tank. (See figure B). The storage tank design becomes an integral part of the total system and is very important to the total function of the system. The cross flow filter system requires only low pressure, and will work with centrifugal pumps, diaphram pumps or in some cases no pump at all. As an example, if we wanted to filter a 10 GPM (37.8 liters/min.) stream that contained 1% of submicronic particulate, we would flow the 10 GPM (37.8 liters/min.) into the storage tank and recirculate through the filter at a flow of anywhere from 30 GPM to 100 GPM (113.6 to 378.5 liters/min.) depending upon the filterability of the particles from the liquid. As the contaminated fluid recirculates, the solids will build up in the storage tank and loop until they reach a level, which is dependent upon the design of the tank. Then the settling rate in the tank becomes equal to the amount of the solids being fed to the tank, and as a result you reach an equilibrium in the amount of solids being presented to the inside of the porous tubing. We have in effect created a dynamic settling tank or thickener. A flow of 10 GPM (37.8 liters/min.) of clear filtrate comes off for either recycle or disposal with periodic removal of thick mud from the bottom of the tank. The thick mud can be either processed through a centrifuge, a rotary drum filter. a flat bed pressure type filter, or other means. Often the small volume of filtrate from the mud de-watering stream can be recycled back into the recirculation tank so that any fines in the feedback are again concentrated, thus closing the loop on the continuous process 100% removal system. Cross flow filtration will not do efficient molecular separation. We work primarily with discrete solids but we do separate them totally from the liquid carrier fluid. I know some of you will raise your eyebrows when I say that we remove 100% of the particulate, but in measurement tests, we have measured the filtrate cleanliness with instruments that record as low as .05 ppm and the instruments read zero, so that it is less than .05 ppm.

Jan 1, 1980

By G. Ansell, J. Weertman

G. Ansell and J. Weertman (Rensselaer Polytechnic Institute and Northwestern University, respectively) —The great increase in creep strength that you found in your indium-glass composites is quite striking. You ruled out a decrease in the dislocation source density as an explanation of the reduced creep rates. Could you tell in greater detail why you feel this is an inadequate explanation of the phenomenon. It appears to us that it is a reasonable one. Consider the spacing between the glass spheres in your composites. It is of the order of 10-3 cm. The spacing between dislocations in a (single-phase) annealed metal with a dislocation density of the order of 106 to 107 cm per cm3 also is of the order of 10-3 cm. Therefore it is not reasonable to expect that the arrangement of the dislocation lines is the same in the composite material as it is in pure indium. If the dislocation arrangements are different the density of the dislocation sources likewise will be different. Another way of saying the same thing is the following. The presence of the glass spheres reduces one of the dimensions of the metal phase to 10-3 cm. Thus the metal phase, in effect, is equivalent to a metal whisker or a thin metal film. These are strong because they have so few dislocation sources within them. T. D. Gulden and J. C. Shyne (authors' reply)—It is to be expected that the arrangement of dislocations in the indium-glass composites would be quite different than that observed in annealed pure metals. The dislocations probably exist primarily as segments connecting the dispersed particles. These segments and discontinuities at the very large area of particle-metal interface could act as dislocation sources. For this reason it was considered unlikely that the very high observed creep strengths were due to a low density of dislocation sources. A more likely explanation is that the distance a dislocation can glide is limited by the interparticle spacing. The particles averaged about twenty in diam and were less than 10 µ apart in the 40 pet composite. It seems reasonable to assume that a dislocation loop in a volume of metal surrounded by these relatively large particles would not bow out around them but would be restricted to the region between particles. A general expression for creep rate is given by the product of the dislocation source density, the average rate at which loops are generated from a source, and the average area swept out by a loop times the Burgers vector magnitude. Assuming that the area swept out is limited by the interparticle spacing and the rate of generation of loops is controlled by the rate of climb of loops over second-phase particles, as suggested by Ansel and Weert-men,9 a calculation of the dislocation source density may be made from the experimentally observed creep rates. The result comes out 10" to 10" per cm3 which seems reasonable in view of the assumptions involved. Thus it is concluded that the anomalously low creep rates that were observed were due not to a low dislocation source density but rather to a limitation on the area swept out by each dislocation loop.

Jan 1, 1964

By J. H. Jackson, P. D. Frost, C. H. Lorig, A. C. Loonam

THIS paper describes (1) the effect of sodium on the tensile ductility of magnesium-lithium base alloys, and (2) the precautions necessary to avoid sodium contamination. Effect of Sodium on Properties The harmful effect of sodium in magnesium-lithium base alloys has been recognized by other investigators.1,2 However, quantitative data on its effect have not hitherto been published. The effect of sodium on the ductility of an 87 pct Mg-9 pct Li-4 pct Zn alloy is shown in fig. 1. The sodium was introduced by adding sodium chloride to the flux, which consisted of 50 pct LiC1-50 pct KC1. Moderately high ductility was obtained at an indicated sodium content of about 0.05 pct. Actually, the value probably was less than 0.05 pct, be-cause analyses of the lithium, which were more accurate than those of the alloy, indicated that the highest ductility was obtained when its sodium content was 0.02 pct or less. In fact, in alloys having somewhat greater strength than this particular composition, the sodium content of the lithium must be under 0.01 pct to avoid embrittlement. The effect of sodium on the ductility of several alloys having fairly low strength levels is shown in fig. 2. These alloys were melted with a flux containing 75 pct LiC1-25 pct LiF, to which various quantities of sodium chloride had been added. Sodium had no significant effect in pure magnesium but markedly decreased the ductility of the magnesium-lithium-zinc alloy, even though the alloy contained only 3 pct Li. As the lithium content of the binary alloys was increased, the ductility of the sodium-free alloys also increased. However, the effect of sodium on ductility became progressively more pronounced. Sodium raised the minimum hot-rolling temperatures, particularly those of the high-strength alloys, but its effect, in this respect, was less critical than its effect on tensile ductility. For optimum cold roll-ability, a low-sodium content was required. No deleterious effect of sodium on the stability of properties at slightly elevated temperatures was found. Control of Sodium in the Alloys Optimum ductility is obtained in the magnesium-lithium base alloys when sodium-free materials are used. Commercial lithium was formerly the chief source of contamination. Now purified lithium is usually available. When lithium of ordinary purity is used, the effects of sodium can be minimized by using a flux consisting of 75 pct LiC1-25 pct LiF. Bubbling nitrogen through the melt also helps remove sodium. The damaging influence of sodium on the ductility of the magnesium-lithium base alloys was observed very early in the alloy development program. The discovery came about as a result of chemical analyses made on the lithium used in the alloys. Ductile alloys had been made from lithium containing about 0.2 pct Na, whereas the lithium used in the brittle alloys contained about 0.9 pct Na. The first magnesium-lithium alloys were melted under commercial fluxes ordinarily used in melting magnesium alloys. These fluxes were unsuited for scavenging the contaminating sodium, and the resulting alloys were not ductile. Next, a flux containing 50 pct KC1-50 pct LiCl was tried. This was somewhat more effective but still was not satisfactory. After a number of different experimental fluxes had been investigated, one containing 75 pct LiC1-25 pct LiF was adopted. This flux made it possible to obtain good ductility in the alloys. The

Jan 1, 1951

By R. M. Douthwaite, G. Birkbeck

The effect of grain size and specimen dimensions on the occurrence and magnitude of a yield point drop in pure iron has been examined. The tests were done at room temperature. The results indicate that gain size is the critical factor determining whether a yield drop occurs. The specimen diameter:gain size ratio does not influence the magnitude of the yield drop for the range of gain size and specimen diameters investigated. HUTCHINSON,' petchY2 and worthington3 have investigated the grain size dependence of the upper yield stress (uUYP) and the yield point drop, ouyp - aLYP, in Armco iron, mild steel, and Si-Fe, respectively. These authors used center-annealed wires to avoid stress concentration from specimen shoulders and to ensure uniformity of the applied stress. Coarsegrained specimens show no yield point drop; the yield point drop then increases as d-'I2 increases (where d is the grain diameter). These results can be understood in terms of Petch's analysis2 in which the magnitude of amp depends on the strain rate in the (limited) number of grains deforming plastically at the upper yield point. If N grains per unit volume are undergoing plastic deformation, the strain rate in the deforming grains is l/Nd3 times higher at the upper yield stress than when the whole specimen deforms homogeneously. If N is constant and independent of grain size at uUyp, then all the grains are deforming when ~d~ = 1, so there is no yield point drop. At finer grain sizes, the yield point drop is given by: where AU, is the friction stress increase corresponding to a tenfold strain rate increase. Christ, Smith, and Burton studied the upper yield point in 0.050-in.-diam wire specimens prepared from zone-refined iron. Each end of the 2; -in. specimens was soldered to a & -in. diam steel ball and the load applied through the two balls. There was a yield point drop in specimens with grain diameters less than 0.1 mm; no drop was observed in specimens of grain diameter greater than 0.1 mm that were free from veining substructure, but specimens of grain diameter 0.129 mm, annealed in the y range, showed an upper yield point. and this was associated with the presence of a veining substructure in these specimens. Christ et al. suggested the upper yield point occurs when more than a specific number of grains fill the specimen cross section so a multiplicity of slip is required to initiate plastic deformation. Table I summarizes the published data on the grain size at which the yield drop disappears. On the basis of this data the ratio of specimen diameter:grain diameter = 5 to 27 appears to be the critical value for the occurrence of a yield point drop. Thus, petch2 interprets the appearance and magnitude of the yield point drop in terms of the limited number of grains deforming plastically at uuyp, whereas Christ et a1. consider that the occurrence of the yield drop depends on the ratio specimen diame-ter:grain diameter. The published data cover a wide variety of materials so some variation between the results is to be expected, but the size range covered in the data of Table I is rather limited. In an attempt to discover whether the specimen diameter:grain size ratio or the grain diameter is critical in determining

Jan 1, 1969