Search Documents

By R. D. Nelson, F. E. Bowman

Evidence has been found for a (010)a?(111)B[102]a /,11[341]/B crystallographic relationship between the monoclinic a and B phases of plutonium during the a?B transformation. The results of an X-ray diffraction study, where [010] fiber textured a samples were used in the absence of suitable single crystals indicate that the (OIO)a planes become (111)B planes upon transformation under near-equilibrium conditions. The transformation strain along the fiber axis, which was the [010] direction, was measured dila-tomekically; the measured 8.5 pct expansion compares favorably with the 8.44 pct expansion in the in-terplanar spacing represented by the (010)a?(111)B relationship. From plots of the atom positions in each of the related planes, a correspondence was deduced between the [102]a, direction and the [341]B direction. Further analysis of the two lattice structures in the light of this relationship revealed a rotation about the [102] direction of 1 deg 43 min and a slight shearing in this same direction of about 30 min. THIS paper discusses the (B crystal structure of plutonium and the orientation relationship existing between the monoclinic a and B phases during the a?ß transformation. The kinetics of the a?ß and (3 — a transformations have received extensive consideration, and because of the crystallographic complexity of these phases, the question of the mechanisms by which these transformations occur is especially intriguing. Nelson and Shyne1 evaluated the existing experimental evidence and concluded, from the indirect evidence available, that both the ß ? a and a ? ß transformations occur by a martensitic process. Their data reveal the anisotropic nature of these transformations which suggests the existence of specific crystallographic relationships between the parent and product phases. In this paper, we are concerned with the confirmation of the existence of such a relationship resulting from the a ? ß transformation and the derivation of the crystallographic details necessary to specify it. EXPERIMENTAL RESULTS X-ray diffraction and dilatometric data were obtained from samples of a plutonium having a [010] fiber texture. These cylindrical specimens, approximately 1 cm in diam, were prepared by transforming the ß phase to a under the influence of a uniaxially applied compressive load.' The [0l0] direction is parallel to the direction of applied stress; it is also perpendicular to the (010) planes. This correspondence between the plane normal and the direction having the same indices is, in the monoclinic a plutonium structure, restricted solely to this (010)[010] combination. Such a specimen was mounted in an evacuated, elevated temperature specimen holder on an X-ray dif-fractometer so that the diffracting surface was perpendicular to the fiber axis. The a diffraction pattern, Fig. 1, taken at about 115ºC, revealed the predominance of the (020) reflection. This monoclinic, P 21/rn space group yields no (0k0) reflections when k is odd. The temperature was raised slowly to 160°C to effect the complete transformation to the phase; then it was lowered to 120°C so that a diffraction pattern of the ß could be obtained near the a = ß equilibrium temperature for direct comparison with the a at the same temperature. The (3 diffraction pattern, Fig. 2, obtained under these conditions showed a (222) reflection relatively much more intense than in the random pattern. The other reflections appearing with sig-

Jan 1, 1970

By R. D. Satterley

The Sherwood mine is an iron-ore mine owned and operated by the Inland Steel CO. in the Iron River district of the Menominee Range in Michigan. The property consists of an 80-acre tract in the village of Mineral Hills, about a mile north of the city of Iron River. The Ore mined is a reddish brown, nonbessemer hematite and limonite. The ore bodies lie in a large syncline having an east-west strike and are associated with a rock structure that is folded in a complex manner. The two 40-acre tracts run north and south and the shaft is at about the center of the north forty. The shaft is 1286 ft. deep, with the principal operating level at a depth of 1000 ft. from surface. A new level at a depth of 1200 ft. is in process of development. The ore body at the 1000 ft. level is east and west at approximately the line between the north and south forties and at this elevation is from 50 to 250 ft. wide and extends above the level at varying heights of from 50 to 250 feet. The 1000-ft. haulage drift extends south from the shaft, through the east-west ore body to the slates on the south side of the body. The ore body was intercepted in the drifting at about goo ft. from the shaft and was about 200 ft. wide at that point. A crosscut was extended to the east and west property lines along the south boundary of the ore body. This east-west ore body is laid out in areas go ft. wide for stoping with pillars 40 ft. wide. With this plan a stope is approximately 80 by 200 ft. and has a pillar on both sides that is approximately 40 by 200 ft. The ore has a height of from 50 to 250 ft. above the elevation of the level, therefore the height of the stopes varies in accordance with the height of the ore body at each location. From the crosscut, two main raises, each 6 by 7 ft., are put up into each 80 ft. stope area (Fig. 1). One of the main raises serves as a manway and the other as an ore raise, through which the ore is transferred from the stope to the tramming equipment. The original layout as for scraping of the ore from under the stopes into the ore raises. The ore raise is put halfway (east and west) along the 80-ft. stope area and usually is in iron formation. The manway and ore raise are on approximately 15-ft. centers. These main raises are Put up to a height of from 22 to 30 ft. above the level floor, then from the toll of the ore raise a scraper drift (8 X 8 ft.) is driven across the width of the ore body, which is in the neighborhood of 200 ft. From the scraper drift, mill raises are put up at 12½-ft. centers, staggered on opposite sides of the drift, and these are extended 23 ft. above the elevation of the scraper-drift floor. The sublevel connecting the top of these mill raises is called a mill "sub." Other sublevels are developed parallel to the scraper and mill subs at 25-ft. vertical intervals above the mill sub. The mill sub and the other subs above the mill sub are known as sublevels or dog drifts, and are 4 ft. wide and 6 ft. high. These dog drifts

Jan 1, 1946

By Ralph H. Sweetser

C. H. Herty, Jr.,* Pittsburgh, Pa.—The procedure of the Open-hearth Committee in studying pig iron and its effects in the open hearth has been influenced by the discussions at a number of meetings of the Committee. Those discussions have brought out very clearly that, as far as the pig iron affects the quality, interference with quality should be studied for three definite types of pig iron: (1) low-silicon pig iron; (2) very high-silicon pig iron, and (3) pig iron in which the silicon varies over a wide range in short periods, such as 1 to 3 casts. If a blast furnace is running steadily at 1 per cent. silicon iron, practically no trouble, apparently, can be traced to the pig iron, but if the furnace is running from 0.60 up to 1.50 and then down to 0.60 per cent., trouble in the finished steel is liable to occur, which apparently cannot be corrected by open-hearth practice. The open-hearth discussions have shown fairly definitely that with low-silicon iron, one type of trouble arises on the finished product and with the high-silicon iron, another. Our experience with the high-silicon is that any non-metallic matter that may form, does so when the pig iron is put into the furnace; that is, silicates immediately form which are more liable to be high in silica than would happen with low-silicon iron. I think Mr. Sweetser will agree with mc that if a blast furnace is very irregular, different points in the furnace may be working irregularly, in other words, the temperature gradient all over the furnace is not uniform. We have made many determinations on that point which indicate that a varying blast furnace causes hot spots and cold spots around the periphery. If some of those spots are hot and others are cold, although the analysis of the iron may be constant, then unreduced oxide, going through on one side, and good iron, going through on the other, may mix and the average temperature of the iron is not high enough to get completely rid of the oxides. So our method of attack is directly on that point; it is our first objective. Our procedure is to make a number of consecutive tests at a blast furnace, making a detailed study of the blast-furnace operation. We follow the iron through the open-hearth heat, being sure that we know just how much of each kind of iron gets into the open hearth, and take out specified samples at certain times during the process, working on steel where no finishing additions are made in the furnace. We are following one type of iron through the billet mills and into the finished product and are obtaining complete data on open-hearth operation. Besides the ordinary chemical analyses on the samples of slag and metal, we are running samples of the plg iron, the steel in the open hearth and the finished steel, for oxygen and silicates. We are going to find out whether or not oxygen, as silicates or oxides, has some connection with this trouble. If not, we may be able to locate some other factor. I am inclined to think that the silicates are responsible, judging from the indications in some other work that the Bureau of Mines is doing in Pittsburgh. We have laid out a very definite method of testing to which we will adhere at the different plants where we are now working and at others in the future. Our aim is to

Jan 1, 1927

By Roshan B. Bhappu, Raul A. Deju

A method is proposed by which the chemical reactions between water and a silicate bed can be related to equations of flow. First the reaction mechanism is studied both theoretically and experimentally. Once the reaction mechanism is established, the equations of flow are solved, and a solution (under physically reasonable side conditions) is obtained. Experiments to substantiate the solution are also presented. The knowledge of surface reactions at the water-solid interface is of critical importance in extractive metallurgy. This is especially true in regard to the froth-flotation process of mineral concentration and all phases of hydro metallurgical recovery of metals. Similarly, the problem of ground-water contamination is one of growing concern, not only because of the increasing demands on our sources of supply but also because of the increasing necessity to find vehicles of waste disposal. The hydrochemistry of waste waters must be understood to exploit and develop such resources properly. To understand these problems, it is necessary to obtain a better insight into the reactions that take place between water and a solid packed bed. To do this, we will develop here in a theoretical model that predicts the fate of a chemical species in solution as it reacts with a silicate bed through which the liquid percolates. The treatment will be one-dimensional in nature and will not include dispersion. Experiments will also be presented to substantiate the theoretical model, using the silicate minerals listed in Table 1. This paper is preliminary in nature and is part of a larger study of the surface chemistry of the silicate-water interface. Mechanism of Surface Reactions In a previous paper,' the authors discussed the properties of various silicate minerals from a mineralogical standpoint. Now efforts will be made to study the reactions that occur when these minerals are put in contact with water. The reactions occur almost entirely in the surface layer of the mineralsa and are termed sorp-tion reactions. In this study sorption denotes the composite of all physical adsorption and chemical adsorption occurring between the silicate surface and the water in contact with it. A model of sorption as seen from a chemical-bond standpoint is presented below. On the basis of this model, the surface reactions between deionized water and a silicate mineral can be studied. Sorption Model: It is known that as the oxygen-silicon ratio increases from quartz to the olivines, a greater percentage of the oxygen bonding power is available for bonding to cations other than silicon. Hence, with an increasing oxygen-silicon ratio, the oxygen-to-metal bonding increases. Upon the fracturing of a silicate-mineral crystal, the oxygen-metal bond breaks more easily than the stronger oxygen-silicon bond, resulting in a negatively charged surface. Then, if the mineral is immersed in a liquid containing hydrogen ions, the negatively charged surface should tend to be neutralized by hydrogen ions from solution, resulting in a change of the solution pH. Thus, an increase in the degree of sorption of hydrogen ions must occur as the oxygen-silicon ratio in the crystal structure increases. Also in a previous paper,' the authors found that for a given silicate mineral the change of pH with time is given by

Jan 1, 1971

By D. M. Boulin, E. S. Greiner

Single crystals of vanadium were bent at 293" and 77°K to a maximum fiber strain of about 1 pct. Analysis of slip line and etch markings of- crystals deformed at either temperature show the slip planes are {112}. The slip directions at 298° and 77°K, deterwined from the asterism axes of rotation of crystals compressed in a {110} direclion, were (111). Etch pits, associated with dislocations, were observed in the plastically deformed vanadium. There was no evidence of mechanical twinning. THIS paper presents results on single crystals of vanadium plastically deformed by bending and compressing at 298° and 77°K. Bcc metals have been observed to slip on {110}, (1121, and (123) planes while the slip direction has invariably been found to be ( 111) 1 Lindley and smallman2 have studied the deformation intension of polycrystalline vanadium between 298° and 20°K and reported that at and above 77°K the deformation is predominantly by slip, but at 20°K the deformation is associated with twinning. Later, Edington and smallman3 found that single crystals of vanadium compressed in a (111) direction at 77°K deformed by twinning on { 112}( 111) systems. Clough and pavlovic4 have reported that mechanical twins were observed in vanadium loaded by impact at 77°, 173°, and 195°K, respectively. PREPARATION OF SINGLE CRYSTALS The vanadium single crystals were made from commercial vanadium reported to contain 0.03 pct C, 0.03 pct 0, 0.02 pct N, 0.0X* pct Ca, 0.0X pct Si, proximately 0.8 cm diam, 4 cm long and were grown in (100) and (110) directions. A crystal for studies of etch pits was gound to have a face parallel to a {l00} plane by the Bond crystal-orienting technique.7 In order to avoid straining, the crystals were placed on the steel mount with a low-melting organic compound (glycol phthalate) before grinding. Crystals for the bending experiments were ground to have the four side faces parallel to ( 100) planes. The crystals were electropolished8 in 10 pct H2So4 using a current density of about 3 amp per sq cm to remove the strained surface material. The crystals were bent slowly by three-point loading in a stainless-steel jig designed by Sylwestrowicz.9 The end rollers of the jig were 3.8 cm apart. DEFORMATION AT 298°K The bent vanadium crystal, after removal from the jig, had a radius of curvature of 20.4 cm over the 2-cm length close to the center loading roller, where the maximum bending moment occurred. This radius of curvature corresponded to a maximum fiber strain of 0.9 pet. The side faces contained slip bands as shown in Fig. 1. These bands are straight where the strain is high, top and bottom of micrograph, but are curved on either side of the neutral axis in the center. This curvature of the slip bands in the low-stress area may be due to cross slip. The plastically deformed crystal was subsequently electropolished and then electroetched in 10 pct H2SO4 solution, using a current density of 0.25 amp per sq cm. The structure is shown in Fig. 2. The directions of the traces on two adjoining faces were plotted stereo graphically, Fig. 3.* Since there were two sets of

Jan 1, 1968

By R. J. Schaefer, M. E. Glicksman

Direct, in situ observation of metallic alloys during solidification reveals that in some systems crystal multiplication occurs by means of a dendrite remelt-ing process, without the necessity of independent nu-cleation events. The solidification is observed on optically clean surfaces of supercooled molten alloys. In one system (Sn-3 wt pct Bi) , a fine-grained equi-axed structure is produced by the complete disintegration, via remelting, of transient initial dendrites. In contrast, several other metallic systems show little or no evidence of remelting activity. The behavior of these metallic systems is consistent with that expected on the basis of published observations of dendrite remelting in transparent organic alloy systems. It is concluded that dendrite remelting is an important crystal multiplication process in some metallic alloys, but is velatively unimportant in some other alloys. The detachment of dendrite branches from the primary stem by a remelting process has been observed by Jackson, Hunt, Uhlmann, and seward1 during the solidification of some transparent organic alloy systems. The branches released by this remelting process can drift free of the primary stem and serve as seeds for the formation of numerous independent crystals. This proliferation of new crystals does not require repeated independent nucleation events, but only modification of the initial solidification structure. The mechanism of dendrite remelting, as described by Jackson et a1.1 and by Tiller and O''Hara,2 is dependent on the transport of both heat and solute and is, therefore, expected to operate only in alloys, and not in pure substances. It was found in the transparent organic alloy systems that remelting occurred primarily in the constricted regions near the base of dendrite branches, where the branches had grown through the solute-rich liquid layer surrounding the primary dendrite stem. It was suggested that impure solid had formed in these constricted regions at a relatively low temperature and had later become unstable as further solidification of purer material raised the temperature. Jackson et al. proposed that the equiaxed zone of metal alloy castings originates from a similar remelting process, and they demonstrated the operation of this mechanism in "ingots" poured from saturated salt solutions. Although these substances were especially selected to show solidification behavior similar to that of metals,3 the remelting mechanism has, until now, been subject to the objection that its operation has not been directly observed in a metallic system. Considering the fact that thermal properties such as diffusivity may differ by as much as two or three orders of magnitude between metals and organic compounds, this objection was considered to be possibly serious. A method has now been developed by which it is possible to make direct optical observations of metals during solidification. This method has revealed transient solidification processes which would not be detected by metallographic examination of totally solidified specimens. In particular, a grain-refinement process in a metallic alloy has been observed to be a direct consequence of the total disintegration of an initial dendritic structure. The influence of an initial, transient solidification structure on the final solidification structure is demonstrated here for the first time in a metallic system. I) EXPERIMENTAL The technique of using a transparent flux to maintain an optically clean metal surface during solidification has been described by us elsewhere.* The

Jan 1, 1968

By Edwin S. Smith

Current research in the phenomenon of liquefaction has indicated some of the in situ material properties which should be considered in the planning of waste deposits. Practical experience in tailings disposal, however, must be combined with the results of theoretical and laboratory studies to develop the most economical and safe techniques against liquefaction failure. One of the many responsibilities of mining engineers and mill superintendents is providing for the safe and economic disposal of wastes (or tailings) that remain after a mineral has been extracted from an ore. The cost of disposal of these tailings exerts a considerable influence on the minimum grade of ore extracted from the mine. It varies to a great extent with each project and is dependent on many diverse factors, such as the local topographical, meteorological and seismological conditions together with the applicable water pollution laws of the area. The process used to extract a mineral from an ore determines the physical characteristics of the tailings and, thus, is one of the more important factors to be considered in the planning of disposal facilities. Today's trends in ore-processing operations complicate the problems of waste disposal: recently developed extraction methods result in the production of finer tailings, the use of lower grade ores produces greater volumes of wastes, and the enhanced land values in the vicinity of industrial plants preclude the former practice of spreading wastes laterally and force the expansion of waste deposits upwards to greater heights. The frequent occurrence of stability problems in waste deposits indicates that many mining organizations may not be employing current soil mechanics concepts and practices. One of the most spectacular, and often most disastrous, types of tailings dike failure is that resulting from liquefaction of the fine particles combined with a breach of the main retaining dike. TAILINGS DISPOSAL Since the many variations in site conditions, ore bodies and extraction processes dictate the general disposal procedures and mill superintendents incorporate special facilities to provide the most economical disposal method consistent with accepted safety standards, it is only natural that there are almost as many different disposal techniques as there are disposal areas. Methods used in the construction of retaining dikes include: (1) transporting granular material from an adjacent borrow pit and (2) mechanically segregating the total effluent and allowing the coarse fraction to form a retaining dike by hydraulic deposition. The location of a plant and the surrounding topography exert the greatest influence on the layout of tailings disposal facilities. Most of the above-ground waste deposits can be classified as side-hill, (Fig. 1,) cross-valley, (Fig. 2,) or stockpile deposits. Side-hill disposal areas are probably the most common type of layout because of the natural advantage of gravity flow, without the disadvantage of river diversion usually needed for tailings ponds formed behind cross-valley dikes. Stockpiles, which are placed on relatively level ground, require four retaining dikes and the effluent generally has to be pumped up into the disposal area. Changing production techniques or developments adjacent to disposal areas have produced variations or partial combinations of these three categories. In a series of articles, Lenhart describes many of the problems encountered in the disposal of tailings and certain innovations used to overcome them. He discusses weaknesses in design and layout and shows that disposal techniques are often learned the

Jan 1, 1970

By B. B. Rath, Hsun Hu

Rates of migration of large-angle boundaries have been studied in zone-refined aluminum crystals, defonned 80 pct by rolling in the (110)[112] orientation at -78°C followed by a recovery anneal at 80°C. Artificially nucleated grains show a marked variation. by an order of magnitude, in their growth rates in different directions. The average activation energy for the migration of all boundaries was found to be about 16,000 cal per mole. The anisotropy of the boundary migration is rationalized on the basis of the boundary structure. It has been observed by Beck and HU,1 Kohara el al,2,3 and Czjzek and Haessner4 that recrystallized grains formed upon annealing Of deformed sing1e crystals of aluminum show anisotropic growth characteristics. Kohara et al. found that single crystals rolled in the (110)[112] orientation, when random nuclei were provided on one side of the crystal by rubbing with emery paper and annealing, developed a sharp recrys-tallization texture on the other side of the crystal upon further annealing. This sharp recrystallization texture consisted of four components, which were related to the deformation texture of the crystal, i.e. (110)[112], by rotations of ±40 deg around each of the two common [ 111] axes' They also noted that recrystallized grains were elongated in directions perpendicular to either of these two common [1111 axes. They attributed this anisotropic growth to the difference in the rate of self-diffusion or diffusion of impurity atoms along the tilt and the twist boundaries. A somewhat similar investigation was conducted by Czjzek and Haessner4 On strained single-crystal sheets Of alum- inum. These authors claimed that the matrix structure of the deformed crystal had a greater effect on the growth anisotropy of the recrystallized grains than did the boundary orientation itself. In the present investigation quantitative measurements of the rate of grain boundary migration in anisotropic growth have been made in zone-refined aluminum (99.9999+pct pure) crystals deformed 80 pct by rolling in the (110) 112] orientation. Crystals of this particular orientation were chosen because of the following desirable features: 1) the crystal does not change its orientation during rolling; 2) the rolling plane contains all the significant crystallographic directions; and 3) when annealed, following deformation, the crystal does not re-crystallize spontaneously but polygonizes to a stable and homogeneous structure. Hence, the initial orientation of the crystal and a constant strain energy in the matrix can be maintained during subsequent grain boundary migration studies. It is essential to keep the driving force constant for the study of boundary mobility.5 EXPERIMENTAL PROCEDURE A cylindrical single crystal of 1 in. diam was grown by the Bridgman method in a high-purity graphite mold. The resistance ratio, R(4.2°K) /R(298°K) , of the grown crystal was approximately 2.0 x 10-4. A number of slices, 1/4 in. thick, were cut from the crystal along the (110) plane and were mechanically and electrolyti-cally polished to remove the strained surface layer. The crystals were then rolled along the [112] direction to 80 pct reduction in thickness at -78°C. To minimize surface friction, the crystals were rolled between two layers of 0.005-in. teflon sheet. Rolling was interrupted, prior to completion, to remove the surface layers and the edges by electropolishing. These and similar precautions in handling the rolled crystals

Jan 1, 1967

By R. M. Jorda

The mechanism of parafin deposition and prevention has been studied in the laboratory using an apparatus which provides a quantitative means of studying parafin deposition on metal and plastic surfaces. The amount, hardness, adhesion, per cent wax and mean molecular weight of parafin deposits appear to be governed by surface roughness alone, all other conditions being constant. Tests of various plastic coatings indicate that most smooth, nonparafinic plastics are capable of reducing parafin deposits in oil wells, but flexible, highly polar, nonparafinic plastics are more suitable for providing long term resistance to parafin deposition in oil wells if the flow stream contains abrasive materials. INTRODUCTION The problem of paraffin deposition is one of long standing in the oil industry.' Crude oils often contain paraffins which precipitate and adhere to the liner, tubing, sucker rods and surface equipment as the temperature of the producing stream decreases in the normal course of flowing, gas lifting or pumping. Heavy paraffin deposits are undesirable because they reduce the effective size of the flow conduits and restrict the production rate from the well. Where severe paraffin deposition occurs, removal of the deposits by mechanical, thermal or other means is required, resulting in costly down time and increased operating costs. The troublesome paraffins are normal hydrocarbons ranging from approximately C15H38 to C38H78 mixed with small amounts of branched paraffins, monocyclic paraffins, polycyclic paraffins and aromatics.' The amount of paraffins found in crude oils varies from less than 1 to more than 30 per cent. Many publications are available which deal with this problem, and perhaps the most significant findings in recent literature are contained in a publication by Hunt3 ho developed the "cold spot tester", a really useful means of investigating paraffin deposition. Hunt's observations led to many generalized conclusions concerning the effect of surface roughness on paraffin deposits. He ascertained that there was an observable qualitative correlation between the severity of paraffin deposition and the roughness of the surfaces which he tested (cold rolled steel, stainless steel and several plastics). Because of the number of meaningful observations made by Hunt, his cold spot tester was modified somewhat and extensive tests were per- formed to study the quantitative relationship between surface roughness and the physical and chemical nature of paraffin deposits. LABORATORY TEST PROCEDURES The cold spot test apparatus consists of a flat circular plate mounted on a curved tube and positioned in a vessel containing a wax-oil solution (Fig. 1). The apparatus is arranged so that the temperature of the central portion of the circular plate can be varied by means of a circulating liquid stream; the test equipment includes provisions for maintaining a constant wax-oil solution temperature and stirring speed. In the paraffin deposition studies, the modified cold spot tester was used as follows. The cold spot probe consisted of a flat circular plat 2 in. in diameter and 1/8-in. thick positioned in the wax-oil solution kept at constant temperature. As in Hunt's earlier experiments," a cold liquid was circulated through a tube connected to the circular plate so that the liquid impinged on one side of the plate cooling the plate from the center outward, causing paraffin to deposit on the side of the plate exposed to the wax-oil solution.

Jan 1, 1967

By R. E. Miner, J. K. Jackson, D. F. Gibbons

Internal-friction measurements were made during isothermal aging treatments of 18 pct Ni maraging-steel wires between 420° and 612°C. A sharp initial drop in the internal-friction level was interpreted in terms of a rapid dislocation recovery reaction. The rate of the recovery was found to be independent of temperature. Truncation of the recovery reaction was apparent in those systems that exhibited the rapid age-hardening characteristics of the maraging steels. It is proposed that this initial hardening response is the result of a low activation energy preprecipitation reaction involving molybdenum. A gradual rise in the internal-friction level at longer aging times was associated with the precipitation of a molybdenum-containing precipitate. CONSIDERABLE research effort has recently been devoted to the mechanisms responsible for the high strength and toughness of 18 pct Ni maraging steels. These bcc martensitic alloys are found to harden during aging at temperatures between 400° and 600°C. The aging response is very rapid with more than half the total hardness increase occurring within the first few minutes of aging, Fig. 1. Precipitate particles have been observed in the later stages of aging by a number of investigators.'-' While the identity of the precipitates remains the subject of some controversy, one or more of the intermetallic compounds, Ni3Mo, Ni3Ti, and Fe2Mo, are almost certainly involved. Heterogeneous nucleation of precipitates at dislocations has been noted8 and cobalt is believed to enhance the formation of fine, homogeneously distributed particles by lowering the solubility of the alloying elements in the martensitic matrix.3,7 Transmission electron microscopy studies of the initial hardening behavior have not been fruitful. Strengthening mechanisms based on atomic ordering have not been generally supported by X-ray and neutron-diffraction experiments.9 In the present investigation, the aging reaction was studied using isothermal-aging internal-friction measurements. The marked sensitivity of internal friction to short-range diffusion and precipitation processes has provided a convenient tool for the elucidation of the strengthening mechanisms operative in the maraging steels. EXPERIMENTAL PROCEDURE An upright torsion pendulum was used to measure the internal friction of several maraging steels during isothermal aging. The pendulum was placed in an atmosphere of helium at a pressure slightly less than atmospheric. To permit measurement of internal friction during the first minutes of aging, the specimens were rapidly heated by passing a current through them in a manner similar to that described by Ang and Wert.10 Thermal gradients in the specimen were largely eliminated by using specially designed specimen grips11 which produced temperature variations of less than 1 pct over 90 pct of the specimen length and less than 3 pct over the entire length at aging temperatures up to 620°C. A proportioning strip-chart program controller was employed to maintain constant specimen temperature during treatments of up to 36 hr duration. A number of vacuum-melted laboratory heats having compositions near that of a typical commercial 18Ni-7Co-5Mo-0.4Ti alloy were investigated. The amount of cobalt was varied from 0 to 7 wt pct in five of the heats. Either molybdenum or titanium was omitted in the remaining two heats. The alloy desig-

Jan 1, 1967

By J. W. Spretnak, H. R. Ogden, A. G. Imgram

The effect of working reduction, stress-relief annealing, and recrystallized grain size on the tensile and notch-tensile properties of molybdenum and Mo-0.5 Ti was studied. It was found that increasing the amount of working reduction increased the strength and reduced the tendencies toward brittle behavior. Stress -relief annealing did not alter the strength but lowered the transition temperature. Increasing the recrystallized grain size lowered the strength and raised the transition temperature. The notch -unnotch strength ratio began to decrease with decreasing temperature at temperatures below those at which the notched ductility fell to zero for all of the micro structural conditions investigated. BEING bcc metals, the refractory metals in Groups Va and VIa (V, Cb, Ta, and Cr, Mo, W) undergo a ductile-to-brittle transition and exhibit brittle fractures at low temperatures. Previous research has shown that molybdenum and tungsten not only have higher transition temperatures than columbium and tantalum but show a marked sensitivity of transition temperature to structure as well.' Recrystallized materials become brittle at considerably higher temperatures than is the case with material having a worked or fibered micro-structure. Evidence of structure sensitivity has also been detected in columbium- and tantalum-base alloys containing appreciable amounts of molybdenum or tungsten such as F-48 (Cb-15W-5Mo-1Zr) and Ta-10w.2 This paper describes the results of research conducted to further evaluate the effects of metal. lurgical structure on the low-temperature tensile and notch-tensile properties of molybdenum and Mo-0.5Ti. The effects of rolling reduction, stress-relief annealing temperature, and recrystallized grain size were studied. Considerable progress has been made in explaining the fundamental mechanisms of the flow and fracture characteristics of bcc metals. Several of these concepts are helpful in interpreting the data obtained in this study. Brittle fractures occur when the highly temperature-sensitive yield strength equals, or exceeds, the temperature-insensitive brittle cleavage fracture stress.3 The rapid increase in yield strength with decreasing temperature, characteristic of all bcc metals, is therefore of primary concern. petch4 has described the yield strength, ay, (stress required to initiate plastic flow) of bcc metals by the expression where ai is the frictional resistance to slip, Ky is a constant numerically equal to the slope of a a vs curve, and 2d is the average grain diamefer. The oi term itself is thought to be composed of a temperature-insensitive component dependent on impurity content and second-phase particles and a temperature-sensitive component dependent on the Pierls-Nabarro force.5 This equation has also been demonstrated to hold for the flow stress (stress required to maintain continued plastic flow).' Brittle-crack nucleation is thought to occur by the coalescence of dislocations piled up in slip planes at sessile dislocations or twin and grain boundaries.7,8 These proposed mechanisms require that a large number of dislocations be released into the active slip planes so that sufficiently large stress concentrations are produced at the dislocation pile-ups to enable coalescence into a micro-crack. Therefore, at least a microscopic amount of slip must occur in some grains to facilitate initial crack formation. Cottrell 7 has predicted that brittle fracture, nucleated by slip, should occur when where ty is the shear yield strength, ß = 1 in un- notched xension, u is the shear modulus, and y is the effective surface energy. This equation incorporates the Griffith concept of fracture that a crack will propagate if the decrease in strain energy equals or exceeds the increase in surface energy.

Jan 1, 1964

By C. S. Matthews, G. L. Stegemeier

In one field in South Texas, approximately 72 per cent of the pressure build-up results show a characteris-i.rtic "hump" (i.e., the pressure builds up and then falls off) which makes interpretation by. standard methods impossible Correlation of size and time of hump with formation permeability. well productivitv index, and method of completion led to the tentativc, conclusion that the humps were caused by segregation of gas and oil in the wellbore after closing-in"'. This conclusion was confirmed by performance of simple laboratory bubble-rise experiments, by theoretical bubble-rise time calculations, and by a detailed calculation of PVT behavior in the well of a particular well Oil which accurate Surface and bottom-hole pressure measure-ments were untile. The hump behavior has since been found to occur in many other fields. The cause, however, is not the mine in all cases. In some of these the hump is trace-ahie to leaks in the tnbing which allow influx from the annulus after closing-in. In other cases the hump is traceable to leaks in the device separating pay horizons in dually completed wells. It is concluded that the recording of both surface and bottom-hole pressures is desirable in wells which show an anomalous build-up behavior. A number of field examples is discussed where use of both sets of measurements enables the cause for anomalous behavior to he found, (and a reasonable interpreation of bottom-hole pressure to be made. INTRODUCTION Theoretically the pressure build-up in an infinite reser-voir should be a linear function of In [(t + at)/nere t is the production time and At a the closed-in time. Some of the variations from this behavior arc well known, such as the curved portion immediately after shut-in which results from after-production and skin effect, and the flattened end portion which results from boundary effects in a limited reservoir. The effect of stratified producing zones and irregular geometrical drainage patterns may also contribute unusual characteristics to build-ups. However, the effect of still another phenomenon—that of movement of fluids within the wellbore—has been neglected in most build-up studies to date. Fluid movements within the wellbore after shut-in occur as a result of after-production, packer failures, leaks in the casing or tubing, or buoyancy of the gas phase when both gas and liquid are present in the well. Each of these movements can influence the pressure build-up, sometimes sufficiently to negate use of the data for computing permeability or stabilized build-up pressure. Examples of each of these phenomena are discussed below. FIELD OBSERVATIONS ON HUMP BUILD-UPS In approximately 75 per cent of the wells in a medium-sized field in South Texas the pressure build-up curves rise to 3 maximum and then decline to what appears to be a stabilized reservoir pressure as shown in Fig. I. Similar behavior has also been observed in wells in other fields in Texas and Louisian:,. Because of the possibility of such behavior being a mechanical failure of the pressure bomb. the bombs were run in tanden into one well which had been known to exhibit this behavior. When both bombs recorded identical curves with the characteristic hump, it was inferred that the unusual build-up is a result of well or forma-

By D. F. Kelsall

The hydraulic cyclone, in simple or modified form, is finding increasing application in metallurgical processing. In this article, the author considers several aspects of conventional applications, less conventional applications and some potential uses of modified cyclones. Information concerning the mechanism of separation within a cyclone and the effect of the major variables is summarized. During the past twenty years, and especially in the last decade, hydraulic cyclones have found increasing application in metallurgical processing as classifiers and, under special circumstances, as thickeners. To a more limited extent cyclones have been used to extend heavy, or dense, medium separation into the finer size ranges, and several attempts have been made to separate dispersions of immiscible liquids with a view to use in the field of liquid-liquid extraction. A large proportion of published work reports incomplete data, applicable only to particular systems. The more useful papers, covering data of relatively wide significance, have been reviewed recently in considerable detail1,2 and no attempt will be made to cover the same material in the present paper. However, before considering several aspects of conventional application, less conventional applications and some potential uses of modified cyclones, it is considered pertinent to summarize information relating to the mechanism of separation within a cyclone and the effect of the major variables. LIQUID FLOW PATTERNS At any point within a simple cyclone the liquid velocity may be resolved into three components, i.e., the tangential or swirling velocity (v), the vertical velocity (w), and the radial velocity (u). The relative values of these components at selected positions within a typical cyclone have been established for water. 3 The extent to which similar flow patterns exist in systems of considerably higher viscosity, or apparent viscosity, operating under conditions of reasonable pressure drop, is not known with precision, but indirect evidence indicates that up to approximately five centipoise there is no marked change. Beneath the bottom of the vortex finder, envelopes of constant tangential velocity are cylinders coaxial with the cyclone, and, at any horizontal level, starting from near the conical wall, this component of velocity increases with decrease in radius (r) according to the relationship vrn = constant (where 0 < n < 1) This holds to regions near the center of the cyclone where v reaches a maximum value at a radius somewhat smaller than that of the inside wall of the vortex finder. At this point, the centrifugal acceleration, v2/r reaches a maximum value. As the radius is further decreased the tangential velocity decreases so that v = r. Above the bottom of the vortex finder there is a tendency for the first relationship to persist to near the outside wall of the vortex finder, until v reaches a maximum and then decreases rapidly as the wall is approached. The two most significant features of the vertical velocity distribution are an approximately conical Table I. List of Symbols v = liquid tangential velocity at any point in the cyclone w = liquid vertical velocity at any point in the cyclone u = liquid radial velocity at any point in the cyclone r = radius from cyclone axis to any point ? = half angle of conical portion of the cyclone ?= fluid viscosity d = particle diameter s = liquid specific gravity p = particle specific gravity d50 = the particle diameter which distributes 5090 to overflow, 50% to underflow e = overflow diameter, in. b = feed diameter, in. G = gpm of feed slurry

Jan 1, 1963

By L. Yarborough, L. R. Smith

This paper presents results of a laboratory study of retrograde condensate recovery by revaporization into dry injection gas. Flow tests were performed in 10.6-ft long sand packs at 100F and 1,500 psi. In three runs methane revaporized the liquid from a n-pentane-methane mixture in the presence of immobile water. TWO of these tests were water-wet, and the third was totally oil-wet. In the three runs n-pentane recovery was complete after 2.5 hydrocarbon PV of injection. There was no significant performance difference between the two wettability extremes. In a fourth experiment, a methane-hydrogen sulfide mixture revaporized a synthetic light, sour condensate. No water saturation was present. Equilibrium compositions and volumetric data were obtained for the four-component condensate. The heavy component, n-beptane, was removed after 6 PV production. Comparison of the effluent fluid compositions with known equilibrium data shows that the flowing fluid was equilibrium vapor and that the mixing zone between equilibrium vapor and dry injection gas was short. Data indicated that complete recovery of retrograde liquid occurred after it was contacted by a sufficient quantity of dry gas. INTRODUCTION When pressure declines below the fluid dew point in a gas condensate reservoir, a liquid phase forms. In this process, referred to as retrograde condensation, the quantity of liquid formed is frequently small enough that the liquid is not a flowing phase. To prevent loss of valuable retrograde liquids, the process of dry gas cycling has been employed for several years as a more or less standard practice. In this procedure the reservoir pressure is maintained above the fluid dew point so that the liquid components may be produced as vapor and then separated at the surface. Although full pressure maintenance by gas cycling seems ideal in terms of preventing liquids loss, several factors can reduce the atuactiveness of such an operation. From a study of a condensate reservoir in Alberta, Canada, Havlena et a1.1 con-cluded that cycling under conditions of declining pressure leads to economic advantages and to a high recovery of hydrocarbon liquids. This study considered effects of volumetric sweep efficiency, retrograde behavior of the original wet gas and revaporization characteristics of the retrograde liquid when contacted by dry gas. The first major work concerning revaporization of liquid in a gas condensate system is that of Standing et a1.2 Calculations based upon the PVT behavior of a recombined gas condensate fluid indicated that all retrograde liquid can be recovered if it is contacted by a sufficient quantity of dry gas. The paper considered the effect of variable permeability upon the recovery of retrograde liquid. Standing et al. concluded that recovery of heavier components in the retrograde liquid is greatest if reservoir pressure is allowed to decline below the dew point prior to dry gas injection. Since the work of Standing et al., several laboratory studies have been reported which show that recovery of hydrocarbon liquids by vaporization into dry injected gas can contribute to increased recovery above that obtained by ordinary production practices. Vaporization from retrograde condensate,3 conventional oil4-7 and volatile oil8 reservoirs has been considered. There is little work that deals with revaporization recovery from condensate reservoirs. This study demonstrates that vapor-liquid equilibrium exists when a dry gas is injected into a porous medium containing retrograde condensate; investigates the effect of wettability on revaporization of retrograde condensate; and provides an indication of the amount of dry gas necessary to

Jan 1, 1969

By A. Steiner, E. Miller, K. L. Komarek

Equations have been derived to calculate the chemical potentials of the components of liquid binary alloys from liquidus and enthalpy data. The equations are applicable to systems with intermetal-lic compounds of limited solid solubility. The liquidus curve of the Mg-Sn system was accurately redetermined, and the melting point of the compound Mg2Sn was found to be 770.5° * 0.3°C. The thermo-dynamic properties of the liquid alloys were calcu -lated from the liquidus data. The activity of tin shows both positive and negative deviations from Raoult&apos;s law and the relative integral entropy is positive. THE phase boundaries in an equilibrium phase diagram are functions of the thermodynamic properties of the coexisting phases. Specifically, the shape of the liquidus curve near an intermediate compound is determined by the properties of the compound and the liquid phase. Hauffe and wagnerl have derived an equation for the chemical potential differences (ui) of the liquid alloys near the congruent melting point when the heat of fusion of the compound and the liquidus curve are known. In their derivation the temperature dependence of the ui value was neglected, and liquid of stoichio-metric composition was chosen as the reference state. To obtain chemical potentials over the ntire composition range of the phase diagram with the pure components as the reference state, equations have been derived which incorporate the temperature dependence of the chemical potentials. Such a thermodynamic analysis can be carried out when the liquidus curve and the enthalpy values are known. The equations have been applied to the redetermined liquidus curve of the Mg-Sn system to obtain the thermodynamic properties of liquid Mg-Sn alloys. The Mg-Sn phase diagram has been studied by various investigators and the results have been compiled and critically assessed by Hansen.2 Preliminary thermal analyses showed that the basic features of the diagram were correct. The system has one congruent melting compound, Mg2Sn, two eutectics, and some solid solubility of tin in magnesium. However, the published liquidus temperatures show considerable scatter. In order to perform an accurate thermodynamic analysis, the liquidus curve between the magnesium-rich and tin-rich eutectic compositions was therefore redetermined by careful thermal analysis using highest-purity starting materials. EXPERIMENTAL PROCEDURE The magnesium metal (Dominion Magnesium Ltd, Toronto, Canada) had a purity of 99.99+ pct with the following impurities (in ppm): 20 Al, 30 Zn, 10 Si, <1 Ni, <1 Cu, <10 Fe; tin (Cominco Products, Spokane, Wash.) contained 99.999+ pct Sn. The graphite crucibles were machined from graphite rods (United Carbon Products Corp., Bay City, Mich.) which had an average total ash content of less than 30 ppm. All the graphite parts were baked out in vacuum at 950" to 1000°C for a minimum of 24 hr to remove volatile organic materials. The graphite crucibles (3 in. long, 1-5/8 in. OD, 1-3/8 in. ID) were tightly closed with a threaded cover (1/2 in. thick) which had a central thermocouple well (2-1/4 in. long, 5/16 in. OD, 3/16 in. ID). Cover and thermocouple well were machined from one piece of graphite. A thin sheath of quartz was inserted in the well to protect the thermocouple

Jan 1, 1964

By G. W. Binkley, R. E. Collins, G. K. Dumbauld

A mathematical analysis has shown that the primary factors affecting the deposition of cement in unfractured perforations during squeeze-cementing operations are: the properties of the cement slurry, the geometry of the perforations, and the filtration time. The validity of the analysis has been substantiated by laboratory investigations. The information presented in this paper makes possible the prediction of the rate of deposition of cement in and about unfractured perforations under given squeeze-cementing conditions, the proper filtration time to control the amount of deposition to any desired value, and the deposition properties needed in cement slurries to restrict to any desired degree the formation of nodes of cement .Solids inside the casing. INTRODUCTION The deposition of solids against a permeable medium by the process of filtration is an important property of a cement slurry. General recognition of the role of filtration in the use of cement in wells is evident in view of the fact that several patents on low-water-loss cements have been issued during the past few years. In the conventional, high-pressure squeeze-cementing technique, a large volume of cement slurry is usually displaced into the area surrounding the perforated interval after the formation has been fractured hydraulically.&apos; Near the end of the job, the pumping rate is slowed or stopped intermittently in an effort to obtain a high pressure in the wellbore. The way in which a high pressure is obtained is not understood thoroughly. but it is be- lieved to be caused by the deposition of a rigid mass of compacted cement particles either in the fractures of the formations or inside the casing opposite the perforated interval. In a method of squeeze-cementing introduced several years ago, a small amount of cement slurry is squeezed into the perforations at a low pressure to avoid fracturing the formation. The filling of the unfractured perforations with cement particles by the process of filtration is important to the success of this technique. Early in the development of this low-pressure squeeze-cementing technique, laboratory and field-size experiments showed that conventional, neat cement slurries were unsatisfactory if the tubing was extended into or through the perforated section of the casing. The extremely high filtration rate of neat cement slurries caused the deposition of a compacted mass of cement inside the casing and made it impossible to remove excess cement by reverse circulation and difficult to withdraw the tubing. Because the need for cements with a reduced filtration rate was obvioils and urgent, modified cements containing 12 per cent bentonite were used until research was completed on modified cements containing 25 per cent bentonite.< These modified cements were useful in the solution of the immediate problem, but the following questions remained unanswered: (I) what is the optimum filtration rate of cement slurries for this application, (2) how long should the squeeze pressure be applied. and (3) how great are the effects of squeeze pressure and well temperature on the rate of deposition? Furthermore, the relationship of the filtration properties of cement slurries to the dimensions of the perforations and the wellbore was unknown. In order to obtain information relative to these basic considerations, a systematic evaluation of all the factors involved in the deposition of Cement during low-pressure squeeze-cementing operations was initiated. Although the work was directed toward an evaluation of the factors influencing the deposition of Cement in the low-pressure squeeze-

By Dwight K. Smith, Greg Carter

Studies have been conducted on The properties of many deep well cementing compositions to determine their Strength behavior over curing periods to 180 days at elevated tem-peratures and 3,000 psi pressure. This pressure results in essentially the .vat, compressive strength as that obtained with much higher pressures in ac-cordance with the findings of an API subcommittee &apos; These different compositions include API C1asses A, E, and F cements containig additives such as retarders, berrtorlite, heavy weight materials and pozzolans. All compositions except mixtures of Poz-zolrrrts and hydrated lime show from mild to severe degrees of strength lass over a temperature rang from -730 to 320" F after setting. Pozzolatl-time compositions actually gain in strength with time at these high temperatures. Other chemical find physical properties evaluated to observe their inter-relation.ship with Strength loss show very little correlation except in per-meability. As retrogression in strength increases, the permeability of set cement increases. X-ray difraction patterns on the set products indicate the formation of certain compounds having little or no strength value in those cementing compositions where strength loss was more severe. INTRODUCTION As a result of the growing trend toward deep well completions, a study has been made on the properties of the various cementing slurries presently in use at elevated temperatures and pressure. The strength of these compositions is of prime importance in selecting the most suitable material for use at high temperatures, to determine WOC time and the proper time to perforate with a minimum of shattering. Of primary interest in this investigation was the strength behavior of various compositions currently in use, and the effect of additives on cement after long periods of curing under severe conditions. Earlier investigators have pointed out that the strength of some cements will increase with increasing curing temperature to about 220 to 340" F, but at higher temperatures a loss in strength occurs at extended time intervals. Studies by the API Mid-Continent District Study Committee on Oil Well Cements&apos; outlined a testing procedure whereby field conditions of temperature and pressure could be simulated in the laboratory.&apos; It was observed that retarded cements undergo changes at elevated temperatures and some lose as much as 50 per cent of their early strength when cured at high temperatures. The scope of these tests was limited to curing periods of 1 to 28 days; additives were not covered in this study. Saunders and Walker&apos; found that the use of additives influenced the strength behavior of cements at high temperatures, but studies were conducted only to a seven-day curing period. Ludwig and Pence&apos; conducted an investigation of two types of cements under elevated pressures and temperatures in an effort to explain the causes of this loss in strength phenomenon. It was observed that with retrogression in strength there were other physical and chemical changes which took place as the cement aged. Today there are a number of cementing compositions available for use at well depths below 10,000 ft. Since all these earlier investigations were limited in curing time as well as the number and type of compositions studied, it was believed that a more extensive study should be conducted on the properties of cements at elevated temperatures, and this work should include those compositions actually in general field use at this time.

By S. J. Burns, W. W. Webb

The dislocation arrangements formed during unsteady propagation of cleavage fractures on (010) planes in LiF have been investigated by high-resolution etch-pit techniques and by X-ray diffraction topogvaphy. In impurity-hardened crystals, cracks propagating in any direction on (010) planes at velocities of about 103 cm per sec are usually accompanied by light plastic deformation which is enhanced wherever the crack is allowed to hesitate. Dislocations with [011] type Burger&apos;s vectors are often formed looped around the crack tip. They are dragged along with the crack tips leaving edge dislocations lying nearly parallel with the clearage surface about 5µ from it. These dislocations are easily overlooked since they may initially intersect with the cleavage surface infrequently and later may disappear from the crystals due to image forces during aging at room temperature. Although the plastic work associated with these dislocations is only comparable with the reversible (010) surface energy, an instability in crack propagation appears due to a limit of the velocity with which dislocations can be dragged along with the crack. Transition to a fully brittle nonplastic fracture mode occurs when the crack velocity exceeds the velocity with which dislocations can be moved by the stress field of the crack. TRANSITIONS between brittle and ductile modes of fracture appear to be common processes in the behavior of materials in which the flow stress is close to the stress at which brittle cracks can propagate. High-strength engineering alloys fit into this category and the transition from ductile to brittle modes of crack propagation may be associated with catastrophic failures in these important materials. The methods of theoretical mechanics indicate the geometrical conditions in which these processes may occur but the detailed mechanisms controlling the generation of dislocations in the initiation of the plastic mode and the process by which the loss of plasticity occurs on transition to the brittle mode are not yet clear. Since these mechanisms are not amenable to direct observation in engineering alloys we have chosen a semi-ductile alkali halide LiF as a model system in which to observe transition mechanisms between plastic and brittle modes of crack propagation. Cleavage cracks in this system are known to undergo a plastic-elastic transition at velocities between 103 to 104 cm per secl and dislocation configurations in LiF are amenable to study by optical-microscopic observation of dislocation etch pits2 and by X-ray diffraction topography.3 We have been able to identify a dislocation mechanism responsible for the transition from brittle to slightly plastic modes of crack propagation in LiF. A model based on this mechanism permits calculation of the critical crack-propagation velocity for this transition and indicates the importance of the stress dependence of dislocation velocity in determining the critical crack velocity. Of course, this model cannot be carried directly over to more complex materials but it is quite possible that its qualitative features are generally applicable. Dislocations intersecting fresh cleavage surfaces in LiF were reported by Gilman,4 by Forty,5 and by Wash-burn et a1.6 Such dislocations were construed to have been nucleated where the cleavage crack hesitated or stopped, near stress concentrators, such as cleavage steps, on the crystal face. The loci of such dislocations deposited On the cleavage plane in bands were called "stop lines" or "deformation zones". Gilman, Knudsen, and walshl measured the velocity of cleavage cracks in lithium fluoride by evaporating thin resistive strips on the crystal side and recording

Jan 1, 1967

By D. I. Bardos, Paul A. Beck

The 1100°c isothermal, sections of the V-Fe-Si, V-Co-Si, and V-Ni-Si systems were studied at silicon contents between 0 and 40 at. pct. The single-phase fields in the 30 and 50 at. pct Mn sections of the 1100°C tetrahedron of the V-&apos;Wn-Fe-Si system were also determined. The direction of extension of the elongated O, R, D, and a-Mn Phase fields suggests that the stability of these phases is determined largely by the electron concentration. The peculiar shape of the above ternary a phase fields, as well as of the a phase fields in the V-;Mn-Si and Cr-MTZ-Si systems is accounted for on the assumption that in manganese-(iron-, coball-, nickel-) rich alloys silicon atoms do not exclude d electrons , while in alloys low in the above components they do. This assumption also leads to the expected electronconcentrations for q and ß-Mn phases formed by transition metals with aluminurn. In earlier work it was shown that in ternary alloy systems of transition elements the a a and certain other phases with complex structure, such as the p and R phases,3 form elongated phase fields extending in a direction corresponding to a constant electron concentration. Recently similar behavior was observed in manganese-rich ternary ß-Mn solid solutions with another transition element and with silicon, germanium, or tin,4 confirming earlier indications3 that ß-Mn is also an electron phase. The alloying behavior of silicon in these manganese-rich alloys sug- gested that the four outside electrons of silicon participate in the bonding and that the predominantly d-like bonding electrons are not excluded from the silicon sites. Presumably, some of the normally unoccupied 3d states associated with the silicon atoms are in these alloys lowered to the Fermi level;4 thus silicon behaves as if it, too, were a transition element. The manganese-rich boundary of the a phase in the V-Mn-Si system,4 as well as in the Cr-Mn-Si sys-tem,4,5 extends approximately parallel to the ß-Mn phase boundary, corresponding to the transition ele-mentlike behavior of silicon described above. However, at lower manganese contents (i.e., in the high-vanadium or -chromium region) the a phase field in both ternary systems mentioned extends in a direction roughly perpendicular to that of its manganese-rich boundary, a phenomenon that is apparently inconsistent with the behavior of silicon in the manganese-rich alloys. A similar, although somewhat less pronounced, extension of the a phase occurs also in the high-vanadium (low-iron) region of the V-Fe-Si system at 1175C, but reportedly not in the V-Co-Si or V-Ni-Si systems at the same temperature.5 The present work was undertaken to investigate in more detail the extension of the a phase (as well as of other electron phases that may be present) in the last three systems and to elucidate this phenomenon, which has not been satisfactorily explained previously. EXPERIMENTAL PROCEDURES Most of the alloys were melted in an arc furnace, using a water-cooled copper crucible under helium atmosphere. The transition metals were of better than 99.9 pct purity and the silicon used was 99.98 pct pure. Alloys containing less than 20 pct V were induction-melted in recrystallized alumina crucibles under argon atmosphere.

Jan 1, 1967

By C. S. Smith, W. M. Williams

THE quantitative study of grain shape in three dimensions has been a difficult one from the practical standpoint. Experiments on grain shape have usually been based on indirect observations of two-dimensional metallographic samples or on grains separated by intergranular corrosion or fracture. The latter method was used in particular by Deschl in 1919 in observing the shapes of ß-brass grains which had been separated with mercury. The similarity in detail of shape and packing that exists between bubbles in a soap froth and metal grains was noted by Desch who remarks that: "Surface tension has an. important share in determining the form of the crystal grains in a solidifying metal and such grains have a tendency to assume the shape of foam cells." More recently the relation between grain shape and grain growth has been studied by Harker and Parker.&apos; The importance of surface tension forces in determining microstructure has been discussed by Smith," and an analysis of the topologi-cal rules that apply to such structures has been made by the same author.&apos; Biologists have made valuable contributions to the general problem of shape and form in an assembly of space-filling cells subject to surface tension forces. Particular mention must be made of the extensive researches of Lewis5,8 on botanical and anatomical tissues, and Matzke and Nestler,7,8 who have made painstaking studies of bubble shapes in different kinds of foam. The present paper introduces a new method of studying individual grains in particular alloys—a method which may well find use in other metallurgical researches, and which seems also to be applicable in biological problems. Metal Grains in Three Dimensions The individual grains in a piece of metal or the bubbles in a soap froth must satisfy two conditions —they must be in juxtaposition so as to fill space and their interfaces must conform to the laws of surface tension. If a further restriction is imposed, namely, that only one type of polyhedron be used, then the sole possibility is an assembly of "minimal" tetrakaidecahedra," each polyhedron having eight doubly-curved hexagonal faces and six plane quadrilateral faces, the angles between adjacent faces being 120". Such cells could be stacked on a body-centered cubic lattice and would be quite stable. For many years it was believed that soap bubbles actually possessed the shape of this ideal body, and the hypothesis was the starting point for several investigations on the shapes of soap bubbles, biological cells, and metal grains. These investigations have shown, what might have been obvious in the beginning, that if the condition of symmetry is relaxed the tetrakaidecahedron is almost never found. If we retain only the rule that all contacts should be in local surface tension equilibrium and that the assembly should fill space, metal grains may then take a nearly infinite variety of shapes and no single one may be regarded as an archetype. These two conditions, which are fully discussed in one of the previously mentioned papers,&apos; lead us to think of a typical grain in an annealed metal as having the following characteristics: 1—A grain may have any number of faces, but usually between nine and eighteen. The faces (each of which is, of course, shared by two grains in the assembly) may have any number of edges, but usually between four and six. Pentagons are by far the most frequent. 2—In the assembly of grains each edge is shared by three faces and by three grains. Each vertex is a point shared by four grains, six faces, and four

Jan 1, 1953