Search Documents

By Robert C. Meaders, Arthur R. MacPherson

Many attempts have been made to eliminate most of the crushing plant and all the grinding plant in the process of ore beneficiation by substituting a combined crushing and grinding unit which could take coarsely crushed ore and reduce it to a fine size in one unit. This unit normally would have no other grinding media than the ore itself. This is true autogenous grinding, as we understand it today, and should be clearly distinguished from pebble mill grinding, where pebbles are substituted for steel balls to grind a ball mill size feed. To compete in efficiency with normal methods of crushing and grinding, the autogenous mill must use less labor and steel to produce an equivalent product at equal or lower power consumption. In general terms, a unit to perform these functions must have means to crush the ore to fine sizes and to then further reduce the crushed pieces by grinding. In other words, to do efficient autogenous grinding, there must be a proper balance established between crushing and grinding rates. There is not much point in crushing at too fast a rate if the grinding means are not present to reduce the small particles to the required product size. The crushing means used in an autogenous mill are impact forces of two kinds, namely, (1) the rock travelling at high speeds striking the shell, and (2) the lifters travelling at high speeds striking the rock. Grinding is probably effected in a manner equivalent to pebble milling.

Jan 9, 1964

By J. C. Williams, M. J. Blackburn

In recent years examination of thin foils of metals and alloys has been widely used in studies of deformation and phase-transformation mechanisms. Applications of this technique to studies of titanium and titanium alloys have been infrequent. Therefore, as a large number of titanium alloys have been investigated in this laboratory, it is proposed to give an account of methods used. Particular emphasis will be placed on some of the artifacts introduced in thin foils of titanium and titanium alloys during preparation. Experimental Procedure. It has been found that a large number of titanium alloys can be electropolished in a solution consisting of 30 cu cm perchloric acid (60 pct), 175 cu cm n-butyl alcohol, and 300 cu cm methyl alcohol. Thin foils are prepared using the window method and the electropolishing conditions listed in Table I. Although this solution is not unique, it is attractive because of its low concentration of perchloric acid and the wide range of alloys for which it can be used. Electropolishing is conducted at below -25°C as above this temperature a brown anodic film is produced on the specimen surface. Temperatures above -25°C also accentuate preferential attack of the 0 phase in the two-phase alloys, which unfortunately occurs at all temperatures. Contamination. It is advantageous to reduce the specimen to a thickness of 25 to 50 p prior to electropolishing, since the low-temperature electropolishing technique results in a low rate of metal removal. Both chemical polishing and grinding have

Jan 1, 1968

By C. O. Babcock

In this Bureau of Mines report, the authors present the results of laboratory tests on the burst proneness of coal. Many researchers have studied the violent breaking of large coal masses in underground mines, called bursts, but the causes remain uncertain. They have often assigned to geology and gas pressure the causative roles. The objective of this work is to show that stress can produce bursts in many coals if constraint is necessary for pillar survival and is suddenly lost. We tested coal samples from 15 mines, in 11 coal seams, in six states in the laboratory, and 13 were made to burst. These bursts were produced in several ways, but segmented steel platens were used in the tests reported. Two parameters analogous to the momentum and kinetic energy were used to rank the burst proneness of the coals tested. Tangential strains over the lower surface of the model coal pillar were measured to reveal a periodic slipping prior to the burst. High-speed motion pictures (350 frames per second) reveal the burst behavior in slow motion. We propose a modified Mohr-Coulomb stress-failure criterion to describe the burst behavior. When the horizontal constraint is suddenly lost with little change in the vertical stress, the Mohr stress circle increases in size dynamically, exceeding the static failure condition. When the inertia of the coal mass is overcome, a burst occurs. We conclude that most coals can be made to burst and that such bursts can be expected in mining at increasing depths.

Jan 1, 1984

The term metamorphism as commonly used means any change in a rock in either form or composition, from whatever cause. By metasomatism, according to Lindgren, is meant a metamorphism that involves a change in the chemical composition of a rock by the addition or subtraction of substance. Certain types of metamorphism are due to the action of mineralizing solutions, and are closely connected with ore deposition; they form, therefore, valuable guides in the exploration for ore- deposits. Other types of metamorphism are due to regional processes, and are not connected with ore deposition. By dynamo-regional metamorphism is meant a primary alteration of rocks over large areas under conditions of pressure, flowage, and heat. This process produces schists and gneisses from either sediments or igneous rocks. It is thought that there is little migration of minerals or of elements in dynamo-regional metamorphism, and that the changes are due chiefly to recrystallization and rearrangement of original minerals in bands with their major axes oriented normal to the direction of greatest pressure. Under these conditions limestones are commonly altered to marble, and sandstones to quartzite, basic igneous rocks to greenstone or serpentine, while rocks of normal or acid com- position commonly yield the usual types of schist or gneiss. Dynamo-regional metamorphism, extending over large areas, has no connection with mineralizing processes, and is, therefore, no guide to ore deposits; while this process has certain features, such as characteristic mineral associations, in common with contact metamorphism, the results of the two processes may usually be distinguished without difficulty.

Jan 1, 1932

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members) The following is a partial list of members and guests who called at Institute headquarters during the period May 10,1917, to June 10, 1917. F. J. Anderson, Cali, Colombia. W. F. Jahn, Kirkland Lake, Ont., Canada. George J. Bancroft, Denver, Colo. W. McA. Johnson, Hartford, Conn. W. F. B. Berger, Denver, Colo. J. E. Jopling, Marquette, Mich. F. J. Brulé, Toronto, Ont., Canada. William Kelley, Vulcan, Mich. J. Murray Clark, Toronto, Ont., Canada. H. M. LaFollette, La Follette, Tenn. Will L. Clark, Jerome, Ariz.. Dorsey A. Lyon, Washington, D. C. G. H. Clevenger, Palo Alto, Cal. James F. Magee, Lancaster, Pa. Paul S. Couldrey, Sound Beach, Conn. M. Ortin, Nijni-Novgorod, Russia. C. W. Crispell, Kingston, N. Y. - C. H. Palmer, Jr., Los Angeles, Cal. George A. Easley, La Paz, Bolivia. Edison S. Pettis, ?Mill Valley, Cal. Bancroft Gore, Butte, Mont. Mortimer A. Sears, Paintsville, Ky. John B. Guernsey, Roanoke, Va. W. J. Uren, Houghton, Mich. Rush M. Hess, St. Louis, Mo. C. E. Visel, New Haven, Conn. E. Hibbert, Nickelton, Ont., Canada. Percy E. Barbour, has resigned his position as managing editor of the Engineering & Mining Journal, to accept the appointment of Deputy Superintendent of the New York State Troopers, with headquarters at Albany, N. Y., with the rank of captain.. He has also been commissioned as captain in the 22nd Regiment, N: Y. N. G., having been formerly 1st Lieutenant.

Jan 7, 1917

THE Institute of Metals Division of the American Institute of Mining and Metallurgical Engineers appointed a Research Committee in 1925 to de-termine what could be done by the Division to promote research work in the United States on non-ferrous metals. It was recognized that a considerable volume of use-ful research work in this field was being carried on by individual industrial companies as well as by the uni-versities and other research institutions, such as the Bureau of Standards. One need only refer to the recent research literature on non-ferrous metals in the TRANS-ACTIONS of the A.I.M.E., and elsewhere, to be con-vinced of healthful research activity in this field. The appointment of the Committee, however, voiced the impression that what was being done was, however excellent, inadequate for the needs of the industry. It was felt that the Division could usefully devote some of its time and effort in stimulating activity in this field. The deliberations of the Research Committee have not failed to develop wide differences of opinion even on the simple questions: (1) whether the Division can aid in any practical manner in this cause and (2) what the features of such aid might be. However, it was clear that there was only one type of research activity with which it could be very usefully concerned, viz., that on subjects of fundamental interest and general application. It was obvious that research work having special objects and more immediate commercial appli-cation should best be left to the industry itself.

Jan 1, 1927

By C. E. Shoenfelt

The deepening of the General Crude Oil Company's No. 1 Meyers, NE. NE. SE. of sec. 22, 24S., 36E., in the Cooper area of Lea County, in April, 1934, resulted in the discovery of an oil field of major importance. The discovery well is an old well drilled by Cranfill $ Reynolds and completed in July, 1929, in limestone at 3438 ft. for an initial production of 90,000,000 cu. ft. (estimated) of 'gas. Deepening operations were started early in April, 1934, and cores were taken from the old total depth of 3438 to 3508 ft. A Haliburton test taken through the drill stem at 3439 to 3460 ft. showed 50,000,000 cu. ft. of gas with an increase of 5,000,000 cu. ft. between 3461 and 3474 ft. When completed the well tested 12,000,000 cu. ft. of gas and 5000 bbl. of oil at 3474-3508 feet. The new oil field—the result of this discovery—is between the Eunice and the Jal fields, closer to the productive area of Jal than to that of Eunice but far enough away from both to be considered a separate area. Eventually, all of these pools may be joined together by productive oil wells to form a single unit of large size. They lie in a general northwest-southeast alignment and the intervening areas have not been condemned by dry holes. In the drilling campaign that followed this discovery, 24 wells were drilled, of which 23 were oil wells with combined initial productions of

Jan 1, 1935

By L. O. Howard

THE practice of using acid-lined converters at the plant of the Old Dominion Copper Mining & Smelting Co. was discontinued early in January, 1913, and they were replaced by basic-lined converters. The new equipment consists of one electrically operated 12-ft. upright converter stand and two basic-lined shells for same. These shells are provided with twenty-four 1 1/4-in. tuyères. The mouths are 5 ft. in diameter. Owing to the fact that there is no bedding system or other large storage capacity between the mine and the smelter, the furnaces must handle as fast as produced ore and concentrates, which may vary considerably from day to day, both in tonnage and copper content. Consequently the converter is often crowded to its utmost capacity by the frequent fluctuations in the daily matte supply. From the foregoing, it will be seen that in no way can the converter be favored by running light charges or by transferring to it from other stands in operation. Neither can it regularly be allowed to cool between blows, and only occasionally can it be run at as low a temperature as might be wished. No copper precipitate or other foreign material high in copper is available to help out the tonnage. Repairs and alterations or the removal of defective tuyères must wait until such time as a slight falling off in the matte supply-allows the converting operations to ease up. These variable conditions all combine to interfere with the systematic operating of the converter.

Jan 7, 1914

By John V. Beall

Probably the only hotel in the world with near 100% occupancy at all times is the modern Hotel Indonesia in Djakarta. However, there is little gaiety among the scores of business men who occupy the hotel because they fret as days grow into weeks in seemingly interminable negotiations with government officials. As one man put it, "time is a dimension that they [Indonesians] have never grasped." But the visitors still come in droves to investigate business opportunities in this sprawling nation of tropical islands which is, with 120 million people, the fifth largest nation in the world. Approximately $300 million is being spent each year in Indonesia by foreign companies and governments. Aid grants from the latter are derived about one third from the United States, one third from Japan and the remainder from many nations. Djakarta is a far cry from pleasant colonial Batavia, as the city was called under the Dutch. The orderly colony of prewar days was managed as an agricultural and trading dependency of Holland. The Dutch did little about educating the people. The islands were controlled by the Japanese during World War II and afterwards there was a war for independence--which was attained in 1949. In the ensuing years, President Sukarno devastated the economy by squandering money on a gigantic scale. A Communist-attempted coup in 1965 resulted in a military takeover and the extermination of Communists. The new government under Suharto, which took over all power in March 1966, found itself in a situation where bare survival was the first consideration.

Jan 1, 1970

By E. S. Machlin

RECENTLY, there has been much activity in the field of nucleation of martensitic transformations.'- One of the problems in this field is the calculation of the rate of nucleation (number of plates nucleated per unit untransformed volume per unit time) in terms of observable parameters. Two such observable parameters are the fraction of the length of a straight line which corresponds to the portion of the total length of the line that lies in the martensitic phase and the number of plates intersected by this straight line per unit length of line. Because of the necessity of a valid answer to this problem, the following investigation was undertaken. Although this problem has been treated in the past, a derivation of the relation between the volume and linear fractions of martensite will be described to illustrate the method used in the succeeding analyses. It is assumed that the martensitic plates are in the form of a right circular cylinder having a small height relative to the radius of the base. The volume fraction of martensite is then: fr = lXNl,hjAl [1] where f, is the volume fraction of martensite, and Nij is the number of plates per unit total volume having the area Ai and the height hi. The linear fraction of martensite is obtained as follows. For the plates having the particular area A, and height h,, the fraction sin 0 dB* will have their cylinder axes between the angles 0 and 0 + d0 to the straight line along which the linear fraction of mar-

Jan 1, 1953

By Erwin S. Sperry

The presence of small amounts of tellurium in certain binds of copper, and its exceptionally deleterious* influence in producing red-shortness of this metal, led the author to conduct a few experiments on the influence of tellurium on the properties of brass. While these experiments were not intended to be exhaustive, they demonstrate that, as far as the rolling of brass is concerned, tellurium, unless it occurs in far greater amounts than exist in refined copper, cannot be called an injurious impurity. In comparatively large amounts it appears to impart cold-shortness to high-brass. Tellurium, the rare element that it is considered to be, has recently been extracted on a large scale from the slimes of an American electrolytic copper-works. They have, in attempts to discover some commercial use for it, sent it out promiscuously and gratuitously in quantities which would lead the young chemical student to fancy that a rare element exists only in name. Through the courtesy of Mr. R. L. Whitehead, of Baltimore, the author was able to obtain somewhat over 2 lbs.,? and use it in quantities which, at the market price, would be prohibitive. In order to add specific quantities of tellurium to brass, a rich alloy of copper and tellurium was previously made. The method was as follows, viz.: Nine and one-half lbs. of Lake copper were melted un-. der charcoal in a new plumbago crucible, and then pound of tellurium was added in small portions at a time. The mixture was stirred with a plumbago-stirrer and poured into

Jan 1, 1903

By Reger, B. David

FOR many years, the belief that the so-called "Clinton" sand of Ohio might produce. oil and gas, if it could be reached, has been prevalent in West Virginia. To test this theory, many hundreds of thousands of dollars have been spent and several extremely deep wells, including the deepest boring of the world, have been sunk at various points. With the exception of one well now completed through the sand and the possible exception of another still in progress, all of these wells failed to reach the goal, either through failure of funds or through drilling accidents. REVIEW OF DEEP DRILLING The subject of deep-sand oil and gas in West Virginia has already been discussed by the author1 and by White.2 In these papers, it was shown that the Upper and. Middle Devonian shales, lying between the Berea oil sand (basal Mississippian) and the Oriskany sandstone (Lower Devonian), thicken steadily from eastern Ohio across northern West Virginia and Pennsylvania; but it was stated that the same rate of thickening did not occur in that part of West Virginia south of the Great Kanawha River and in the adjoining portion of Kentucky. In spite of this great eastward thickening, the fact that both the Oriskany and "Clinton" sands, the latter of which is equivalent to the White Medina of New York, exist in great thickness all along the Appalachian Mountains farther east, was held as proof of their probable presence in the deep Appalachian basin.

Jan 3, 1925

Works Manager or General Superintendent.-Technical graduate, for position with a company whose works consist of a large machine shop and foundry. This company manufactures well-known power plant equipment. Location, Pennsylvania. Salary, $5000-$8000 per year. R-871. Motion Study Engineer with extensive experience in shop operation and motion study. Must have sufficient technical experience to recognize inefficiency and waste in plant. Salary, $175-$200 per month. Location, New Jersey. R-876. Metallurgical Engineer.-Technical graduate with at least 2 or 3 years' practical experience in the operation of zinc smelters. Duties will be to take charge, under the guidance of -the superintendent of the smelter, of the operating end of the furnaces, and the roasting kilns, as well as the mix room and ore crusher. Man desired should not be over 30 years of age and should be progressive and able to handle men. Salary, $250 per month. Location, Oklahoma. R-877. Private Secretary to Vice-president in charge of development department and laboratories of large manufacturing plant; must be technical man of good personality, and A-1 in every respect, as position is an important and responsible one. Location, Ohio. R-896. Sales. Engineer familiar with his local territory, particularly with the fanning trade. Should have had at least 2 years' experience in selling tractors; and in any event, must have had at least 5 years' experience in selling machinery. High grade, energetic, and capable; man who is not satisfied with less than $3000 per year and who can earn up to $7000. Location, Iowa. R-897.

Jan 8, 1919

By Henry G. Petrow, Edward S. Porter

MAJOR occurrences of lignite with significant uranium concentrations have been reported in western parts of the Dakotas, especially in Harding County, S.D., and Billings and Slope counties, N.D. Samples containing as much as 2 pct U3O8 were received at the Winchester Laboratory, but those deposits reportedly of major significance have generally contained 2 to 4 lb of uranium per ton of lignite. Most of the uranium appears to be associated with the carbon in the lignite as a urano-organic complex, although in most instances analysis of inorganic material has shown uranium values. Molybdenum is similarly associated with the carbon, and its concentrations generally parallel the uranium. The noncarboniferous material is mainly composed of gypsum, jarosite, bentonite, sandstone, and miscellaneous carbonates and silicates. The heating value of these lignites has been determined as about 3500 Btu on a dry lignite basis. The ash content of lignite has varied widely, the important samples containing 30 to 60 pct ash on a dry lignite basis. Because of the significant upgrading of uranium values obtained by ashing the lignite, and because recovery of uranium from raw lignite presented formidable processing problems, major emphasis at Winchester has been placed on devising methods to recover uranium from lignite calcines. Proper roasting removes the problem of organic fouling of solutions, reduces the size of the leaching plant for an equivalent uranium throughout, and generally provides equal or better acid leaching efficiency with less acid than can be obtained from the raw lignite.

Jan 9, 1957

By George S. Miller

Now that low-carbon steel is manufactured successfully in large quantities by the Bessemer process, and threatens to displace wroughtiron for nearly all purposes, it becomes interesting to find how its Specific gravity compares with that of wrought-iron. The general name "steel" is retained in this paper to designate that metal made by the Bessemer process, which might be more properly called " ingot iron." But the former name seems to be quite firmly established in the iron trade. This steel offers many inducements to the manufacturer of architectural iron, by reason of its hornogencity, and the large masses in which it may be readily moulded. The steel from which these determinations have been made, was produced in four-ton heats and cast into ingots of about 3100 Ibs. weight, having an average section 14'' by 14". These ingots were rolled in a blooming-mill to a section about 24" by 14", cut into slabs and rolled in a plate-mill to a plate .065" to .165" thick, and about 1411 in width. The specific gravity was obtained from pieces of this plate. The metal showed by analysis .10 to .12 per cent. carbon,.33 to .45 manganese,.060 to .072 sulphur,.075 to .082 phosphorus, and .010 silicon. The samples were not annealed, but were brought to a bright surface with a file. All figures given are averages of not less than three determinations on separate pieces from the same plate. The variation in the figures from which the averages were made in no case exceeded .015.

Jan 1, 1886

By Haim Chiswik

IN recent years considerable attention has been devoted to the devel-opment of new commercial uses for silver, chiefly because of lowered prices and large stocks of the metal. This has led to increased interest in the phase diagrams of silver alloys. The silver-lead diagram is reported' to be of the simple eutectic type, but no measurements of the solubility of lead in silver have been made. The solubility of silver in lead has been estimated2 from diffusion experiments and resistance measurements to vary with temperature from 0.09 to 0.18 atomic per cent (0.05 to 0.10 weight per cent). Silver-rich silver-lead alloys have recently been recommended as high-strength bearing metals.3 The silver-bismuth diagram is similar.' The solubility of bismuth in silver has been estimated to be about 5.5 weight per cent on the basis of X-ray work.4 Matthiessen5 found a solubility of silver in bismuth from 0.25 to 0.50 per cent by conductivity measurements. Silver and thallium form the same type of diagram,1 with no data on their mutual miscibilities. We have studied the first two of these diagrams by X-ray methods, verifying their main features and determining the solubilities of lead and bismuth in silver at several temperatures. We also determined the solubility of thallium in silver at one temperature. The solubilities of silver in lead and in bismuth were found to be too low to be detectable.

Jan 1, 1940

By E. C. Harder

SINCE early in 1916, when it became apparent that the steel industry of the United States could not depend, for the duration of the war, on several important foreign sources of manganese and might have to depend entirely on domestic ores, the U. S. Geological Survey, with the assistance f several cooperating organizations, has made a comprehensive investigation of domestic manganese resources. The work has included field studies in a number of states as well as annual, quarterly, and monthly canvasses among operators concerning current and future production. In order that the interested public might have access to the important results of the studies, preliminary reports concerning the field work as well as periodic summaries of production were issued as promptly as possible. Although large deposits of rich manganese oxides appear to be lacking in the United States, small deposits of high-grade material are numerous and widely distributed and large low-grade deposits are found in several places. The principal districts in which high-grade manganese ore is mined, in the order of their importance as recent sources of production, are: Philipsburg district, Mont.; Butte district, Mont.; Southern Nevada region; Central California region; Bisbee district, Ariz.; Appalachian region of Virginia; Batesville district, Ark.; Tintic district, Utah; and Cartersville district, Ga. Scattered deposits of some importance are found in western Arizona, southern California, eastern Tennessee, southern Oregon, and central Utah. The formation of many manganese oxide deposits appears to be related to the physiographic histories of the regions in which they occur.

Jan 5, 1919

By G. L. Spencer

There is no question as to the importance of the part played by the retort in modern zinc smelting. A satisfactory retort should have properties that will result in resistance to slagging action and fire cracks, and have no tendency, or at least only a small tendency, to soften and bend under furnace heat. The life and cost of a retort also are extremely important factors. The trend in zinc smelting during the past few years has been toward longer retorts and .higher charge density. This is caused by the fact that the diameter is limited to 9 or 10 in. because of heat penetration difficulties in larger sizes. Consequently, increasing the length of the retort and density of charge offers the only practical means of increasing the amount of zinc produced per retort. The stiff-ness of a retort perhaps is the most important factor, as slag accumulates in the bottom of a retort which has sagged and very quickly cuts through, often ruining the retorts below. The development of the high-silica retort is a result of the demands made by the trend toward heavy charges. Materials Used for High-silica Retorts The materials used in the manufacture of high-silica retorts at East St. Louis are fireclay, grog and silica flour. Analyses are given in Table 1. The fireclay comes from the St. Louis district. The grog consists of clean firebrick culls, and the silica flour, a very high-grade material, is purchased in the form of a flour that has been ground through 140 mesh.

Jan 1, 1931

By Walter Weeks

CONSIDERABLE difference of opinion seems to exist as to whether the rate of air flow when a fan is placed on a given duct should be determined by the use of static pressure or total pressure characteristics. A little study will show that both methods are correct. Assume that a fan is connected to a duct by an expansion piece as shown in Fig. 1, and that steady flow is established. Considering the atmospheric pressure as zero pressure, let the static head at the outlet of the fan be h and the velocity at this point be v1. The total head at the outlet is then h + v1/2g? The total head at this point must be equal to the total head at the end of the duct plus the losses that have occurred between the two points. Let f be the friction loss in the straight duct, s the shock loss in the dif- fuser, and V2 the velocity at the end of the duct. Then h+ v12/2g=v22/2g + f + s FIG. 1.-FAN ON DUCT. A curve showing the value of the left-hand side of the equation for different rates of flow is the total pressure characteristic of the fan, while a curve showing the value of the right-hand side is the total pressure characteristic of the duct. If these two curves are plotted on the same chart, the intersection indicates the rate of flow when steady flow is established.

Jan 1, 1930

By Niels Hansen

Dispersion-strengthened sintered aluminum products are normally manufactured from surface-oxidized aluminum powder, SAP,' or from atomized aluminum powder.' The powder-blending technique consisting in mechanical mixing of the constituents has been used in the manufacture of numerous dispersion-strengthening alloys, but has never been successfully applied to aluminum alloys. This technique may, however, be applicable if it is possible to produce an unagglomerated mixture of the constituents in the form of fine powders, and the present study was initiated to test this assumption in the aluminum/aluminum oxide system.3 Table I lists the two grades of aluminum powder and the aluminum oxide powder used in the manufacture of the alloys. MD 105 A is an aluminum powder with an average grain size less than 5 IJ., which is isolated from the MD 105 powder by centrifugal separation in cyclohexanol. The aluminum powders and the aluminum oxide were blended in a high-speed blender and then subjected to cold compaction and hot compaction at 550" to 600°C. Subsequently the compacts were hot-extruded with an extrusion ratio of 15 to 1. The alloys were evaluated by tensile testing at room temperature and at 400°C, microscopic examination, and heat treatment at 500°C followed by tensile testing at room temperature. For the purpose of comparison, a commercial SAP quality supplied by Swiss Aluminium Ltd. was tested in the same manner. The tensile data at room temperature and at 400°C are plotted in Figs. 1, 2, and 3 as a function of the weight percent of oxide. The oxide content

Jan 1, 1964