Search Documents

By Charles W. Schwartz, Subash Kolluru

INTRODUCTION Creep of rock in situ, like most rock mass behavior, will be largely governed by the behavior of the natural discontinuities -- bedding planes, faults, and joints, in particular, Several past studies have investigated various aspects of the time-dependent deformation of rock discontinuities; examples include Amadei and Curran (1980), Engelder and Scholz (1976), Johnson (1975), Kaiser and Morgenstern (1979), Solberg et al. (1978), and Wawersik (1974). These studies have provided much insight into the general phenomenon, but they have also produced some inconsistent conclusions and left many unanswered questions. This paper will attempt to shed some light on one of these questions: What is the influence of stress level on the creep of unfilled rock joints? The discussion will follow a two-part approach to the problem: (1) laboratory creep experiments on small scale jointed specimens, (2) a simple theoretical mechanism to explain, at least in qualitative terms, some of the results from the experimental program. EXPERIMENTAL PROGRAM Uniaxial creep tests were conducted on intact and jointed samples of a specially formulated gypsum plaster "synthetic rock." Synthetic rock materials have several advantages over natural rock for long-term creep testing: (a) higher creep rates, (b) lower strength and therefore lower loading requirements, (c) simpler specimen preparation, and (d) more controlled and consistent properties. Gypsum based plasters have been used previously in studies of short-term strength and deformability of jointed samples (Patton, 1966; Einstein and Hirschfeld, 1973). Furthermore, Williams and Elizzi (1977) demonstrated that natural gypsum, at least, creeps in a manner similar to that of most other creep-susceptible natural rocks.

Jan 1, 1982

By Kenzo Murao, Sei Nakao

HISTORY OF ASHIO SMELTER The Ashio copper mine, which formed the main part of Furukawa mining industry, is located inland of Kanto area, and is known as the oldest copper mine of Japan. The mining started even since 1610, and Mr. Furukawa began management in 1877. Afterwards, within a short period, the mine became to have the highest productivity in the Far East. The total quantity of mined copper reached approximately more than 800 thousand tons. The mother rock of the ore deposit in Ashio was rhyolite, and was formed of sissurefulling and irregular clod that was called Kajika deposit. The lode was nzrrow of 6 to 7cm. The mineral was formed mainly of chalcopyrite, including also pyrite, pyrrhotite, and arsenopyrite that were not favorable. After the founding of the copper mine, the Ashio smelter started the operation of Mabuki process as the beginning in 1611, and subsequently adopted the processes of the blast furnace, reverberatory furnace, and flash smelting furnace of the present use. As indicated above, the copper ore of Ashio mine included arsenic. For the purpose to remove it, the operation of the arsenic trioxide production using MacDougall's multiple hearth roaster was started in 1918, and it maintained the status of having the most qualified technique within the country. However, as the completeness in the disposition of anti-pollution and safety had been requested in those years, we studied and developed a unique equipment in 1970. It excludes the heavy metals especially arsenic and copper from the waste water of sulfuric acid process of Flash Smelter's exhaust gas.

Jan 1, 1976

By C Gunther

The term metamorphism as commonly used means any change in a rock in either form or composition, from whatever cause. By metasomatism, according to Lindgren, is meant a metamorphism that involves a change in the chemical composition of a rock by the addition or subtraction of substance. Certain types of metamorphism are due to the action of mineralizing solutions, and are closely connected with ore deposition; they form, therefore, valuable guides in the exploration for ore-deposits. Other types of metamorphism are due to regional processes, and are not connected with ore deposition. By dynamo-regional metamorphism is meant a primary alteration of rocks over large areas under conditions of pressure, flow- age, and heat. This process produces schists and gneisses from either sediments or igneous rocks. It is thought that there is little migration of minerals or of elements in dynamo-regional metamorphism, and that the changes are due chiefly to recrysallization and rearrangement of original minerals in bands with their major axes oriented normal to the direction of greatest pressure. Under these conditions limestones are commonly altered to marble, and sandstones to quartzite, basic igneous rocks to greenstone or serpentine, while rocks of normal or acid com- position commonly yield the usual types of schist or gneiss. Dynamo-regional metamorphism, extending over large areas, has no connection with mineralizing processes, and is, therefore, no guide to ore deposits; while this process has certain features, such as characteristic mineral associations, in common with contact metamorphism, the results of the two processes may usually be distinguished without difficulty.

Jan 1, 1932

By Thomas M. Drown

THE means relied on to attain uniformity in Bessemer steel may be enumerated as follows : I. The appearance of the flame. II. The appearance of the slag. III. The spectrum of the flame. IV. Examination of the steel itself. At present, I wish briefly to bring forward a few considerations with reference to the last two mentioned, namely, the conditions favoring the employment of the spectroscope and examination of the steel. From the amount of careful investigation which has been devoted to the examination of the Bessemer flame by the spectroscope, both on the part of scientists and practical metallurgists, one might reasonably expect some results definite and satisfactory in their nature, first, as regards the nature of the flame, and second, as to the practical value of the spectroscope as a guide in conducting the process. We find, in fact, however, that uncertainty and confusion still exist. In Germany, where this subject has received the greatest attention, it is now very generally conceded that manganese is the cause of the well-known groups of dark bands that characterize the Bessemer spectrum. Nor is it easy to see how we can avoid accepting this conclusion, when Wedding and Von Lichtenfels have produced the manganese spectrum and found it to correspond closely with that shown by the Bessemer flame. But it is evident, on a moment's reflection, as Roscoe has recently brought forward, that manganese cannot be the only cause of the Bessemer spectrum, for we notice the characteristic bands quite as

By hydrometamorphism is meant the alteration of rocks, ores and minerals by atmospheric waters. In its broadest sense, it includes the varied processes of weathering, oxidation, hydration, the leaching of rocks and ores, and the solution, migration and enrichment of metals. Rain water, as it strikes the earth, is practically pure water, except for small quantities of dissolved atmospheric gases; upon coming in contact with ore minerals, especially sulphides, however, it is transformed into solutions of great chemical activity, which attack, transform and rearrange the minerals of ore- bodies, and so effect enrichments of the greatest economic importance. Primary deposits so low in grade as to be without commercial value are frequently thus transformed into deposits of commercial importance. It is necessary in the examination of any orebody, therefore, to determine whether the valuable ore is of primary or of secondary origin; if primary, its value may be expected to continue indefinitely in depth to the zone of primary impoverishment; if secondary, the ore deposition is known to be controlled by surface agencies, and the valuable ore may be expected to continue to such depths only as have been reached by surface waters. The decomposition and weathering of rocks, unlike the changes undergone by orebodies, are accomplished by water carrying as dissolved constituents chiefly atmospheric oxygen and carbon dioxide, together with vegetable acids. The chemical changes wrought are principally hydration, oxidation and the formation of carbonates. The tendency is toward the solution of the more easily dissolved minerals, which is attended by the formation and a surface concentration of the more resistant minerals,

Jan 1, 1932

By E. Topuz, G. Faulkner, M. Karmis, C. Haycocks

The Appalachian coal region of Virginia, southern West Virginia and Kentucky and the extreme eastern portion of Tennessee constitutes a unique area of surface coal mining activities. The area contains a number of contiguously placed coal seams, up to a total of fourteen in some places, which vary in thickness from a few centimeters to 2,5 meters. Much of this coal is of high quality, some being the highest grade metallurgical coal found anywhere in the world. The region may be broadly characterized physiologically as a dissected plateau with a relief above the valley floors of up to 500 meters and a dendritic drainage pattern. Up to six seams may outcrop in the hillsides above drainage, many of which have been subjected to contour stripping operations. Prior to the passage of the surface mining reclamation act, little effort was made to reclaim stripped areas. The passage of the strip mining act, including the controversial requirement for returning the land to its approximate original contour, has forced intensive recla¬mation efforts from the mining industry. The wisdom of this original contour requirement has been the subject of considerable debate and litigation, mainly because of its cost, inconvenience, and value of the land after it has been reclaimed. Regardless of whether recla¬mation is carried out, under current practices slope failures do occur. This in effect circumvents the intent of the law and can expose large unvegetated spoil areas, and contribute to hillside erosion and stream silting. Such failures must be eliminated if further costly reclamation efforts are to be avoided.

Jan 1, 1983

By Thomas M. Drown

THE means relied on to attain uniformity in Bessemer steel may be enumerated as follows I. The appearance of the flame. II. The appearance of the slag. III. The spectrum of the flame. IV. Examination of the steel itself. At present, I wish briefly to bring forward a few considerations with reference to the last two mentioned, namely, the conditions favoring the employment of the spectroscope and examination of the steel. From the amount of careful investigation which has been devoted to the examination of the Bessemer flame by the spectroscope, both on the part of scientists and practical metallurgists, one might reasonably expect some results definite and satisfactory in their nature, first, as regards the nature of the flame, and second, as to the practical value of the spectroscope as a guide in conducting the process. We find, in fact, however, that uncertainty and confusion still exist. In Germany, where this subject has received the greatest attention, it is now very generally conceded that manganese is the cause of the well-known groups of dark bands that characterize the Bessemer spectrum. Nor is it easy to see how we can avoid accepting this conclusion, when Wedding and Von Lichtenfels have produced the manganese spectrum and found it to correspond closely with that shown by the Bessemer flame. But it is evident, on a moment's reflection, as Roscoe has recently brought forward, that manganese cannot be the only cause of the Bessemer spectrum, for we notice the characteristic bands quite as

Jan 1, 1873

By Dorsey Hager

THE rapid increase of water troubles in the Mid-Continent oil fields is causing much alarm. Troubles occur at Towanda, Eldorado, Augusta, Cushing, Blackwell, and Healdton, although they had, not been acute in the Mid-Continent field until about two years ago, when the unusual conditions in the deeper oil fields were first encountered. California faced the same situation, but, thanks to aggressive measures, has largely overcome the dangers. The following analysis of water trouble may throw some light on the subject and be of assistance in solving the problems involved. WATER TROUBLES CLASSIFIED The presence of water in large quantities in oil sands has the following results: 1. Diminishes oil production. 2. Diminishes casing-head gasoline production: (a) By curtailing the gas flow. (b) By making the use of vacuum pumps unsuccessful. 3. Increases lifting costs: (a) By making it necessary to pump large quantities of water, which requires. a fast motion and long stroke (third hole). (b) By requiring the use of compressors for air lift. (c) By causing break-downs and delays due to the high speed necessary to pump water. (d) By making it necessary to treat "cut" or emulsified oil. Oil production is seriously curtailed by the presence of large quantities of water. Lease records show that wells are shut down 40 to 60 per cent. of the pumping time where serious water trouble occurs. While a small quantity of salt water may cut the paraffine and keep the oil moving, several hundred feet, or a hole full of water, effectually "kills" the oil

Jan 10, 1918

By Henry M. Howe

This paper gives the results of an investigation of the beha vior of the argentiferous cobalt-nickel arsenides of Temiskam-ing, Ontario, in roasting, made in the metallurgical laboratories of the School of Mines of Columbia University in the City of New York. The ore was kindly given by the owners of the La Rose and Trethewey properties at Cobalt, Ontario, and Mr E. J. Hall, Tutor in Assaying in Columbia University, has helped us much. I. Object of the Investigation. The object of the investigation was to learn: 1. The temperature at which the arsenic is most rapidly expelled ; 2. The thoroughness with which it is expelled by prolonged roasting at this temperature; 3. The effect of adding charcoal (a) near the end of the roast and (b) at. the beginning of the roast. II. Nature of the ORe. The important ores mined in the Temiskaming deposits are: native silver—with small amounts of dyscrasite (Ag,Sb), ar-gentite (Ag,S), pyrargyrite (Ag,SbS,)—smaltite (CoAs,), chlo-anthite (NiAs,) and niccolite (NiAs). Mispickel (FeAsS) and cobaltite (CoAsS) also occur in smaller quantities. The average composition of the ore shipped from this district for the first six months of 1905 was: silver, from 4.1 to 4.8 per cent.; cobalt, from 6.9 to 8.2 per cent.; nickel, from 3 to 4.7 per cent.; and arsenic, from 30.9 to 34.6 per cent. The ore which we treated consists chiefly of smaltite. In our 1aboratory-work

Jan 1, 1908

By Richard Moldenke

ONE of the gravest problems of the iron foundry today is the accumulation of sulfur in commercial scrap and its effect on the castings made therewith. The ordinary jobbing castings today show a sulfur content of 0.18 per cent., and occasionally as high as 0.22 per cent. The product of the foundry during the war is undoubtedly .to blame for this rapid increase and conditions will become worse as the millions of tons of gray-iron castings of the war period return to the foundry in the form of commercial scrap. In the ordinary cupola remelting of pig and scrap, at least 0.02 per cent. sulfur is taken up; often double that amount. The high cost and difficulty of obtaining pig iron during the war period compelled the use of considerable scrap in the mixtures; frequently charges containing. 90. per cent. of bought scrap were melted. Naturally the sulfur content of the castings increased. Until the advent of the basic-hearth electric furnace, the only method of holding the sulfur within reasonable limits was to use high percentages of pig in the foundry mixtures. Pig iron seldom contains over 0.05 per cent. sulfur, if well made. With pig iron forming 60 percent. of the .charge and the gates, runners, rejections, and bought scrap the other 40 per cent., the sulfur content of the castings can easily be held down to 0.10 per cent. Pig iron, however, costs more than scrap even when melting loss differences are considered, hence as small a percentage as possible will be used.

Jan 2, 1921

By Effingham Humphrey

THE Lehigh Valley. Coal Co. finished the rebuilding of its Drifton No. 2 breaker at Drifton, Pa., in the summer of 1917. The new construction comprises an addition and the complete remodeling of the old breaker. It is of interest to note that the old structure was the first iron breaker erected in the anthracite region. THE OLD BREAKER This old breaker was built by the Cross Creek Coal Co., under the direction of the late Eckley B. Cole, in 1888-89, and was fully described by him in the Transactions.1 The columns were cast iron, 8,'10 and 12 in. square. The floors and partitions in pockets were cast-iron ribbed plates. The struts were cast iron of "H" section; the other members were of structural iron either rolled I-beams or built-up sections. The sizes of the rolled beams varied from 6 to 20 in. deep, while the built-up sections, made of plates and angles, varied from 6 to 63 in. in depth, so that there apparently was no rule to determine the type of section used. In the remodeling of the old structure, practically everything was taken clown excepting the columns and roof, and such beams as were necessary for temporary construction purposes, and, therefore, a close inspection of the old structural members could be made and the effect of the acid water oil them could be noted. The cast-iron members were but slightly attacked by the water, while the wrought-iron beams, in the wet places, were corroded almost to failure.

Jan 2, 1918

Man: A purely detached consideration of nature and the place of man in it may easily result in somewhat pessimistic conclusions as to man and his destiny. However, when we come to the evaluation of man's role in the development of natural resources and his achievements in this field, a more optimistic tone may be justified. Hence the possible contradictions between Man and Nature, Perfection, and the present chapter are more apparent than real. After all, progress must have a foundation of optimism, and we cannot challenge either the faculty or the students to better work and to a progressive and constructive outlook without an underlying tone of optimism and basic faith in the future. Geology is the basic science of Mother Earth; the science of the natural forces that have produced and modified the structure of our globe; the science of minerals and rocks; of landscapes and soils; of water supply and mineral resources, including mineral fuels; and of the history of life, both plant and animal, as revealed by fossils in rocks. It is difficult to reduce man and his historical significance to their proper relationship with regard to the earth and its history. Processes of rock formation have continued for at least two billion years; man's activities have been in evidence only a few thousand years. As a means of comparison, if the height of the Empire State building were to represent geologic time, the thickness of a nickel placed on the tower would just about repre-

Jan 1, 1950

By Prince Gelasio Caetani

PRESIDENT DWIGHT'S invitation to be a guest of the American Institute of Mining and Metal-lurgical Engineers was the first of the subsequently very numerous invitations to dinner I have received from my American friends. When I received his telegram I had not yet been even formally appointed Ambassador. I cannot tell you how deeply I appreciated it. It was a hearty welcome in returning to your country which has been for me a second home and it came from the American mining brotherhood which has been my second family.There are two distinct periods of learning in life. The first one are the years spent in school where we learn many things we after-wards forget; the second one are the years of prac-tical apprenticeship which engrave indelible signs in a man's character and shape his life. These latter years I spent in the United States and they have influenced the whole course of my life. I owe very much to my American friends who trained me. The earliest was Prof. Robert Peele, of Columbia University. At the Daly West mine, in Park City, Utah, he curbed my futuristic English spell-ing and had a hard time at it. Prof. James F. Kemp taught me that geology is a guess work just as unre-liable as the prediction of international events; he taught me also that a frank, honest and loyal character will lead a man equally straight through a mining report and through public life.

Jan 3, 1923

By Y. Jeannin, C. Mannerskantz, F. D. Richardson

Measurements have been made between 1040o and 1300°C of the equilibrium between chromium metal, chromic oxide, hydrogen, and water. The results are in closer agreement with those deduced from recent thermal data than with previous equilibrium values. They lead to the equation ?G°1300°-1600°k = -266,700 + 59.95T ± 300 cal for the formzation of a mole of Cr2O3 from chromium and oxygen. This same equilibrium has been studied with the chromium dissolved in solid iron, and in this way chromium activities in Fe + Cr alloys have been established. The measuremenis show that there are substantial positive deviations from ideality in the a, and b phases, and support the results obtained by Heymer and Kubaschewski against those of other investigators. There is considerable disagreement between existing data,1"4 which is referred to in the Discussion, concerning the equilibrium Cr2O3 + 3H2 = 2Cr + 3H2O [l] There is also substantial disagreement between the results obtained by various investigators5-' who have measured the activities of chromium in its alloys with iron by the Knudsen effusion vapor pressure method. In view of the importance in metallurgical processes of chromium and its oxide and of Fe-Cr alloys, an attempt has been made to study equilib- rium [I] both with pure chormium metal and with chromium alloyed with iron, at temperatures between 1040o and 1300oC. From the work with the alloys it is possible to derive the chromium activities from the relationship

Jan 1, 1963

By V. S. Rood, J. A. Norden

The general system of workings at the Utah-Apex is similar to that found in many of the western metalliferous mines. There is a vertical three-compartment shaft extcnding to the surface, from which the various levels have been driven to the orebodies. The 1000-ft. (305-m.) level, about 3/4 mile long, was driven as a haulage and drain adit. Geology The formation is a flat north-dipping series of alternating limestone and quartzite beds. Extensive north-south faulting and fissuring have taken place, resulting in the formation of large replacement orebodies in the crushed zones in the limestone. The orebodies are irregular in shape and size, but follow closely the trend of the mineralizing fissures. The ore consists of galena, pyrite, sphalerite and small values in silver and gold. Large masses of non-commercial pyrite are frequently found in or adjacent to the orebodies, and more or less pyrite is found for some distance in the walls of the orebodies. Lenticular bodies of a black pyritic shale also occur in the zones where extensive faulting has taken place. Mining Methods and Condition of Workings Geological conditions, mentioned before, have made the ground extremely heavy. In mining above the 1000-ft. level, square-set and filling methods were used, but not altogether successfully. The crushing of timbers extended even into the filled portions of the stopes. The filling material itself, consisting of limestone, shale, and pyrite, possessed swelling qualities which added to the difficulty of maintaining

Jan 1, 1920

By G. H. Billings

There exists an unconfirmed opinion among many ironmasters that the combination of a small quantity of manganese, chromium, titanium, tungsten, aluminium, nickel, and some of the metalloids with iron has a beneficial effect upon the quality. And the impression prevails in some localities that the excellence of steel greatly depends upon the influence of some of these elements. Brit as the recorded experiments are so meagrely described, and made under such various conditions, the student in search of information upon the subject is somewhat bewildered by the contradiction of the opinions expressed. Observing some interesting phenomena while experimenting with an alloy of iron, copper, and nickel, I was led to determine the effect of some of the metals upon iron as free from contamination by other elements as it is possible to procure in practice, in order that the result of an alloy of an individual metal with iron might be more closely studied; for it is almost an impossibility to determine the influence of a small amount of one element upon a metal combined with a large amount of another, and the mere presence of another sometimes makes this difficult. And as most of the experiments recorded upon this subject have been made with iron containing sufficient carbon and other elements to interfere with the effect of that metal the influence of which it was desired to observe, I have endeavored to avoid these sources of error as far as practicable. In determining the specific gravity of the alloys in these ex-

By H. l. Burghoff

THE presence of tellurium in copper and, by inference, in copper alloys, has been considered seriously detrimental and has been avoided. In particular, very small amounts of tellurium have been found to produce red-shortness, although the effects on cold-working and ordinary physical and mechanical properties have not been known so definitely. References in the literature are few, but as long ago as 1881, Egleston1 reported that 0.083 per cent tellurium in fire-refined copper rendered the copper red-short and therefore worthless for hot-rolling. In hot-rolling copper cakes containing this amount of tellurium, he found that fine cracks appeared in the cakes on the first pass through the rolls, the cracks opening further in successive passes. When cold, the metal was said to be tough and malleable. A few years ago, during the course of an investigation in our laboratory on copper-base alloys, it was found that tellurium-bearing alloys could be machined much more freely than similar alloys not containing tellurium. The study was pursued further in this direction, and considerable data were obtained, which indicated that certain tellurium-bearing alloys might have properties of commercial interest. The work eventually led to patent protection,2 a wide range of tellurium-bearing copper-base alloys being covered. This article presents results obtained on the effect of tellurium on the. mechanical properties of three copper-base alloys: commercial bronze (90 Cu, 10 Zn), 1.5 per cent tin bronze (98.5 Cu, 1.5 Sn), and silicon bronze (96 Cu, 3Si, 1 Zn).

Jan 1, 1937

By H. Rush Spedden

R. T. Hukki has extended his study of ball mill grinding at supercritical speeds with an excellent mathematical analysis of tumbling mill grinding. When he speaks of supercritical speeds he is referring to the original Fahrenwald critical-speed formula. He said that, as an example of the use of supercritical speeds, if a fine grinding mill of any type is wet-grinding ore of 3.5 sp gr with steel balls at a certain conventional subcritical speed, the same power input and capacity should be obtainable with autogenous medium of 3.5 sp gr at a speed 100 to 120 pct of the critical in a grate- type mill of the same effective size. In addition, he introduced what he calls the base mill concept which, he stated, makes it possible to compare performances of mills of different sizes grinding with a metallic medium or with an autogenous medium of any specific gravity and at any speed. He showed the use of this concept and explained how it makes possible the evaluation of mill sizes and motors for any grinding purpose at any accuracy well within the conventional standards of design in milling practice. He further stated that the maximum capacity in pilot plant mills with various media, either metallic or autogenous, has always been found to be within the supercritical speed range. In his discussion of this paper he substantiated these findings with statements showing the increased capacity obtained in a milling plant in Finland which followed his principles.

Jan 7, 1960

By G. H. Billings

THERE exists an unconfirmed opinion among many ironmasters that the combination of a small quantity of manganese, chromium, titanium, tungsten, aluminium, nickel, and some of the metalloids with iron has a beneficial effect upon the quality. And the impression prevails in some localities that the excellence of steel greatly depends upon the influence of some of these elements. But as the recorded experiments are so meagrely described, and made under such various conditions, the student in search of information upon the subject is somewhat bewildered by the contradiction of the opinions expressed. Observing some interesting phenomena while experimenting with an alloy of iron, copper, and nickel, I was led to determine the effect of some of the metals upon iron as free from contamination by other elements as it is possible to procure in prac¬tice, in order that the result of an alloy of an individual metal with iron might be more closely studied ; for it is almost an impossibility to determine the influence of a small amount of one element upon a metal combined with a large amount of another, and the mere presence of another sometimes makes this difficult. And as most of the experiments recorded upon this subject have been made with iron containing sufficient carbon and other elements to interfere with the effect of that metal the influence of which it was desired to observe, I have endeavored to avoid these sources of error as far as practicable. In determining the specific gravity of the alloys in these ex-

Jan 1, 1877

By John F. Burst

GENETIC correlations of the various types of Cheltenham fireclays found in Missouri have been the subject of several papers. The correlations usually have been attempted on the basis of stratigraphic and leaching patterns (Wheeler,18 1896; Allen, 1,2 1935 and 1937; McQueen,13 1943). Herold10 (1943), as well as Allen,l,2 has dealt at length with the mineral¬ogy of Missouri fireclays and postulates genetic relationships from min¬eralogical findings. Both researchers cite kaolinite as the primary clay mineral of the Cheltenham formation and suggest that differences in physical proper¬ties are due to clay mineral impurities such as halloysite or illite (not recog¬nized by the name "illite" at the time of Allen's papers). By ascribing the differences to impurities, it is possible to use weathering as the only major alteration factor. This paper seeks to probe still farther into the clay mineral composition of the Cheltenham formation and to show thereby that the mineralogical differ¬ences that have been found to exist within the "kaolinite" component of the Cheltenham fireclay may alter somewhat the previously held theories of diagenesis. Two Missouri fireclays, which have been rather thoroughly investigated, were chosen for comparison of genetic relationship to clay mineral content. One is a typical plastic fireclay of the middle Cheltenham (McQueen's classification13) obtained at Mexico, Audrian County, Missouri, from a large open pit operated by the A. P. Green Fire Brick Co. The other-a typical hard flint fireclay-was obtained from a pocket deposit in southwestern Mont¬gomery County, Missouri.

Jan 1, 1952