Search Documents

By George B. Clark

7.1-1. Introduction. The fundamentals of blasting involve both the properties of explosives and of the rock being blasted. While the knowledge of property correlation between rocks and explosives for most effective blasting is far more complete, many quantitative evaluations have been made. Four of the most important explosive properties appear to be energy density, bulk density, rate of energy release, and the pressure-time history of the gases produced. Important rock properties are density and porosity strength, and energy absorption properties, including the effective moduli of elasticity. Rock structure also has a marked effect on its breaking properties, i.e., joints, bedding, fractures, alteration, etc. Several mechanisms enter into rock fragmentation by blasting. These include slabbing, radial fracturing, crushing, and bursting by the gas bubble. All of these factors are closely related to properties of both explosives and rock. Slabbing depends upon the character of the first generated stress wave, whose shape and magnitude are a result of the pressure generated by the explosive, its time history, and the resultant response of the rock, including its ability to sustain the stress wave. Actual slabbing, in turn, is a function of the magnitude and shape of the pressure pulse and the tensile strength of rock. Further fragmentation depends to a great extent upon the amount of gas in the bubble and its energy and pressure. Blasting rounds are best designed by taking the above factors into consideration. This is effectively accomplished by use of cratering curves which relate breakage- parameters to the explosive energy. Optimum depths from single charge cratering curves must be adjusted to changes in shot geometry and related to multiple hole blasting. Blasting damage may occur from either air blast or ground waves, and in the latter ease may be due to direct vibration or to settlement caused by vibration. Technical information indicates that blasting damage is often

Jan 1, 1968

By F. H. Gilpin

SINCE Noah pitched his ark within and without with pitch, the use of asphalt in human endeavor has been increasing-for Noah's pitch was asphalt. Asphalt is a bituminous material found in nature, either pure or admixed with smaller or greater quanti-ties of mineral and non-mineral materials, or obtained by the refining of crude asphaltic-base petroleum under proper methods of control. Native or "natural" asphalts are scattered through-out the world, though the commercial value of the various deposits varies greatly, depending upon both their accessibility and magnitude and the quality of the material found. It is an acknowledged fact that such asphalts have been produced through natural causes by practically the same application of tempera-ture and pressure as are used in the modern refining of crude asphaltic-base petroleum. The best known of all the native asphalt deposits are those of Trinidad Lake in the Island of Trinidad, British West Indies, and of Bermudez Lake in Vene-zuela. Asphalt from Trinidad Lake, after refining to remove organic and some inorganic diluents, contains approximately 35 per cent, of inorganic residue, and the asphalt thus produced must be fluxed with lighter asphaltic or semi-asphaltic base oil to make it com-mercially utilizable. The refined asphalt obtained from the Bermudez Lake deposit contains from 4 to 6 per cent. of inorganic material which cannot be removed. This asphalt, also, must be fluxed to produce com-mercial products. Small quantities of similar materials are available in other locations. The best pure native asphalt' is known as. gilsonite and is mined in com-mercial quantities in the State of Utah. In numerous places in the United States, particularly Oklahoma and Kentucky, there are deposits of sand¬stone and limestone impregnated with bitumen, which are known as rock asphalts. These rock asphalts may be used, particularly in the paving industry, either as found or by slight fluxing; from some deposits the asphalt is extracted and marketed commercially.

Jan 2, 1923

By Lyndon L. Foley

The proper spacing of oil wells is a problem of vital importance to the oil industry. Conservation demands a maximum recovery, while economic considerations attach primary importance to profitable extraction of oil. Formulas have been evolved,1-4 which attempt to solve the spacing problem mathematically, using reservoir characteristics as factors. Comparisons have been made of fields producing from supposedly similar sands, which have been drilled to varying densitiesl5,6 and also of different leases in the same field. 5-8 Intermediate wells have been drilled in old, depleted fields to test the efficiency of drainage by the original operation.9-11 Intermediate wells have been drilled also to obtain cores of the depleted sand for analysis, from which to learn the degree of efficiency of extraction. The problem is being attacked by many students, and along several different lines. Unfortunately, the fields now depleted were produced generally without restriction, and conclusions drawn from them may not apply to fields operated under restricted production. Reservoir conditions in a restricted field, especially reservoir pressures and pressure gradients within the reservoir, are quite different from those in a field produced to capacity. Many people have held the idea that the closer the spacing, the greater the recovery. This general statement is not always true, as other factors than well spacing enter into the recovery problem. Cutler,5 who has been quoted frequently by advocates of close spacing, limited his conclusions to gas-drive fields, and to the particular fields and spac-ings that he investigated. Hill and Sutton7 analyzed four tracts in the Powell field; the tract most closely drilled had the third largest recovery per acre-foot, and the tract with the widest spacing had the second largest recovery per acre-foot. A search of the references to well spacing in the publications of the U. S. Bureau of Mines5,13-19 discloses repeated condemnations of the wastefulness of the practice of town-lot drilling.

Jan 1, 1938

By Neil O. Johnson

In the cyanidation of gold, silver and mixed ores, the solids, suspended in the pulp after fine grinding, primary settling and scries agitation arc subjected to a washing step known, generally, as countercurrent decanta-tion, abbreviated C.C.D The conventional C.C.D. plant consists of a series of separate thickeners—three to five in number—arranged in series on slightly different elevations. Solids settled in the first thickener are pumped at maximum density into the second thickener, where they arc diluted with weak solution overflowing the third. After settling in the second thickener they are pumped to the third, where the process of repulping with still weaker solution is repeated, and so on throughout the system, until they reach the last thickener and are repulped with barren solution or water. Recently there has been developed a new type of thickener, known as the Dorr Washing Tray Thickener, consisting of up to five individual thickeners, which performs in a single unit all the functions of a conven-tional C.C.D plant. Fig. 1 illustrates the essential features. It is a multicompartment tray thickener, in which the trays operate in scries instead of in parallel for countercurrent washing. Feed enters the top compartment via a central, semisubmerged feed well. Strong solution overflows into a peripheral launder. Solids settle to the bottom, are raked to the center and flow into the top of the second compartment, directly below, via an inverted cup and scal. Solids pass downward, compartment by compartment, against a counter flow of wash solution and finally of fresh water. Thus, in accord-:trice with the basic C.C.D. principle, the solids transfer the dissolved metal content to the wash solution and finally are removed by a diaphragm pump from the bottom compartment virtually free of valuable material. Similarly, the wash water, as it flows through the system, becomes increasingly enriched in dissolved metal until it overflows from compartment two and returns to the process.

Jan 1, 1939

By A. Patton

Introduction THE use of roll scale in the Bessemer process dates back, to the "best of our knowledge, at least 20 years. It was first used by the Ohio Steel Co.; Youngstown, Ohio (now the Ohio Works of the Carnegie Steel Co.) under the direction of Sam, MacDonald, Superintendent of the Bessemer Department at these works. Two 10-ton vessels and one blowing engine capable of blowing one heat at a time were employed. The object of using the scale was to -shorten the length of the blow; or in other words, to increase the production with the same equipment. Various means were tried out for introducing the roll scale into the bath of molten iron: It was shoveled into the vessel before the heat was charged, so that the metal would flow over the scale; it was shoveled into the bath after the vessel was turned up; it Was dumped into the empty iron ladle by the wheelbarrow-load, and at times wars dumped on top of the molten metal in the iron ladle. But the practice of introducing the scale into the iron ladle had to be abandoned on account of danger from explosions and of skulling the -ladles. It was soon learned that the proper place to charge the scale was in the empty vessel, so that when the molten iron was poured into the vessel it flowed over the scale, causing a considerable reaction to take place before the heat was turned up. Eventually, cylindrical chutes similar to those now in use were installed. Into these chutes the scale is dumped and carried into the empty vessel. Before this convenient means of introducing the scale was adopted, the Ohio Works had satisfactorily demonstrated that roll scale would increase production, by blowing 107 heats in one 12-hr. turn (1,087 tons) with one blowing engine, blowing one heat at a time; whereas, prior to the use of scale, the best practice at these works was about 80 heats under the same conditions.

Jan 2, 1917

By William P. Blake

Copper Basin in Yavapai county, Arizona Territory, about twenty miles southwest of Prescott, is well named. It is a depressed area, and a region of cupriferous impregnation.* The geologic conditions are simple. The foundation rock is a coarse-grained granite and gneiss, in which soda feldspar predominates. There are also dykes of porphyritic rock, and a large quartz vein containing pyrites. Superimposed on this crystalline foundation, we find heavy beds of mechanically formed rocks, conglomerates, breccias, and sandstones, in horizontal layers cropping along the bed of a creek, and apparently the remnants of a much more extended formation, now denuded and largely carried away by gradual atmospheric erosion. The heavy beds of conglomerate are in many places much broken and tilted up, even standing on edge in large blocks, as if they had been lifted by some great convulsion; but the cause is much more simple, being merely the removal by gradual disintegration and erosion of the softened and decayed granitic rock below. The materials of these sedimentary beds are chiefly fragments of granite, gneiss, and plutonic rocks loosely mingled. They are the chief repositories of the copper-ore, which forms the cementing substance. This copper-ore is the blue and the green carbonate, azurite and malachite, and the ore is so generally spread through the mass of the beds that the blue and the green croppings can be seen at a great distance, particularly after or during a shower of rain, when the colors are extremely brilliant and beautiful. The copper carbonate is not only a matrix and a cementing material for the fragments of rock, but it invests and covers these fragments so that only malachite and azurite are visible. The beds are from three to ten feet or more in thickness, and, although seemingly solid carbonate of copper, rarely contain over 12 or 15 per cent. of that metal. Some portions of the conglomerates are much more highly charged with copper than others, and in places the beds are almost without copper. If a lump of the coarse sandstone

Jan 1, 1889

By W. A. Selvig

BY plotting fixed carbon against British thermal units of coals free from mineral matter, and ranging in rank from anthracite to lignite, it is found that the coals of higher rank, from anthracite to the higher rank of the high-volatile bituminous coals, inclusive, can be separated into groups according to their degree of metamorphism by reference to their fixed carbon. Such charts show also that the coals lower in rank can be best separated into groups with respect to B.t.u., especially when plotted on the moist basis, that is, coal containing its natural bed moisture. A tentative scheme for coal classification was presented at the October, 1932, meeting of the Technical Committee on Scientific Classification, of the American Standards Association Sectional Com-mittee on Coal Classification. This scheme was sponsored by Sub-committee IV on Tentative Classification of Coals, under the chairmanship of W. T. Thom, Jr. It proposed the grouping of coals according to rank by reference to fixed carbon and B.t.u., on the basis of coal containing its natural bed moisture but free from mineral matter. This scheme proposed classifying coals into four broad classes: (1) anthracitic, (2) bituminous, (3) subbituminous, (4) lignitic.. The anthracitic class was divided into three groups designated as meta-anthracite, normal anthracite, and semianthracite. The bituminous class also was divided into three groups, low volatile, medium volatile, and high volatile. The high-volatile group was further subdivided into four subgroups according to moisture content, as follows: (1) less than 5 per cent, (2) 5 to 10 per cent, (3) 10 to 15 per cent, and (4) 15 per cent and more. The subbituminous class was divided into two groups, group, 1 including subbituminous coals having calorific values of 10,500 B.t.u. or more, and group 2 including those with less than 10,500 B.t.u. , The lignitic class of coal was divided into two groups both below 8,000.B.t.u., the one group consisting of consolidated and the other of unconsolidated

Jan 1, 1934

By C. W. Washburne

The waters of many oil fields have been regarded as buried sea water which has been retained in the sediments since the time of their deposition. The preservation of connate water through geological time has seemed improbable to only a few geologists, but there is room for doubt that buried sea water could remain in the strata during their periods of deformation and during the many subsequent epochs of the circulation of meteoric ground-water. Some have even suggested that the calcium chloride water in the deep mines of the Lake Superior region is ancient sea water buried in the Algonkian lavas, but it is hard to understand how such water could be derived from the highly sodic and sulphatic water of the sea. It would seem more plausible to connect the calcium chloride with the highly calcic magmas of the greenstones in which it is found. Chemical analyses of waters associated with oil differ widely from the composition of sea water, requiring extensive alteration of the latter, if the former is truly its derivative. The first notable difference is the general absence of sulphates from oil-field waters, but this has been explained satisfactorily through reduction by hydrocarbons and organic matter. Oil reduces sulphates with the production of hydrogen sulphide (or sulphur), water, and carbonates (or carbon dioxide). The second striking difference is in the high ratio of chlorine to sodium. An examination of the analyses of chloride waters from oil fields shows that they contain a large relative excess of chlorine over that in sea .water. -Moreover, there is difficulty in finding chemical reactions that are probable in nature, by which sea water could be converted into anything like the chloride waters of oil fields. In the latter a large part of the chlorine occurs as calcium and magnesium chloride. This condition might be produced by the removal of sodium carbonate, which, however, cannot be precipitated in the presence of much calcium or magnesium.

Jan 1, 1915

T. W. ROBINSON, Pueblo, Colo.: Mr. Potter's review is a striking testimony to the important part played by science in this branch of practice. But, the question arises, In which department has science effected most ? The available raw material, the size of furnaces, the general design and equipment of the plant, and the daily management, are particulars, each of which contributes to the general result, while the effect of each merges into that of the others. The following notes concerning the operations of the furnace-plant of the Colorado Fuel and Iron Company (formerly the Colorado Coal and Iron Company), at Pueblo, may throw some light upon the question of their relative importance. This company operates three stacks, and when the plant first came under my observation, about nine months ago, the furnaces were constructed, equipped,and run as stated below: Raw Materials.—The main sources of ore-supply were, as they still are, the Orient and Calumet mines of the company. The Brecce and Morning Glory ores, mentioned below, were formerly brought from Leadville, but are practically now no longer used. The Orient ore is a porous brown hematite, easily reducible in the furnace. The Calumet is a magnetite, very refractory in character, requiring preliminary roasting. Both are fairly uniform in composition. The Breece and Morning Glory are red hematites, resembling in appearance the soft ores of the Vermilion range, Lake Superior. The coke here used is made of coal from the company's mines in southern Colorado, and is distinct from that produced by the company in the western part of the State. The structure is similar to that of Alabama coke. The limestone employed is a calcite. The analyses are given in Table I. I would note, parenthetically, that I know of no section of the country presenting harder conditions for furnace-practice than these materials impose. Results cannot be measured by the more

Jan 1, 1894

By Neil Johnson

IN the cyanidation of gold, silver and mixed ores, the solids suspended in the pulp after fine grinding, primary settling and series agitation are subjected to a washing step known, generally, as countercurrent decanta-tion, abbreviated C.C.D. The conventional C.C.D. plant consists of a series of separate thickeners-three to five in number-arranged in series on slightly different elevations. Solids settled in the first thickener are pumped at maximum density into the second thickener, where they are diluted with weak solution overflowing the third. After settling in the second thickener they are pumped to the third, where the process of repulping with still weaker solution is repeated, and so on throughout the system, until they reach the last thickener and are repulped with barren solution or water. Recently there has been developed a new type of thickener, known as the Dorr Washing Tray Thickener, consisting of up to five individual thickeners, which performs in a single unit all the functions of a conven-tional C.C.D. plant. Fig. 1 illustrates the essential features. It is a multicompartment tray thickener, in which the trays operate in series instead of in parallel for countercurrent washing. Feed enters the top compartment via a central, semisubmerged feed well. Strong solution overflows into a peripheral launder. Solids settle to the bottom, are raked to the center and flow into the top of the second compartment, directly below, via an inverted cup and seal. Solids pass downward, compartment by compartment, against a counter flow of wash solution and finally of fresh water. Thus, in accord-ance with the basic C.C.D. principle, the solids transfer the dissolved metal content to the wash solution and finally are removed by a dia-phragm pump from the bottom compartment virtually free of valuable material. Similarly, the wash water, as it flows through the system, becomes increasingly enriched in dissolved metal until it overflows from compartment two and returns to the process.

Jan 1, 1939

By G. W. Garside

In order to render my descriptions more intelligible, I have compiled a general map of this section of Alaska, showing accurately the relative positions of the most important districts where valuable deposits of minerals have been discovered (page 819). Upon inspection of this map, it will be observed that the chief metalliferous belt in this mineral field is in close proximity to the mainland shore, the trend of which it follows for more than a hundred miles in a northwest and southeast course, while the mineral croppings on the adjoining islands are much shorter in extent, and more irregular with respect to their strike and continuity. This principal metalliferous zone, which I will call the main-land system of lodes, contains gold, silver and lead, besides traces of copper, zinc and iron, gold being found extensively in a free state and also associated with sulphur, and with many of the sulphides of iron, lead and other substances. On the line of this belt, as shown on the map, there are a number of distinct mineral districts. Beginning at the southerly extremity, they are named as follows: Sumdum, Snettishham, Grindstone Creek, Sheep Creek, Gold Creek, Lemon Creek, Montana Creek and Berners Bay districts, each deriving its name from the hay or creek on which it is situated. Harris mining district, as legally organized under the local customs, rules and regulations adopted by the miners of Juneau, embraces, within its exterior boundaries, Grindstone, Sheep, Gold and Lemon Creeks, and all of Douglas Island. The limits of this immense metalliferous horizon are becoming definitely known through the exposures made by prospectors. The belt, as now recognized, varies in width from one to several miles, the lateral measurement being greatest at Juneau in Harris district, where the famous Treadwell mine, with its slate foot-wall, marks the westerly boundary of the zone, while the eastern side of Silver Bow Basin, with a granite hanging-wall, defines its easterly border.

Jan 1, 1893

By A. W. Fahrenwald

The function of the c1assifier in modern fine-grinding practice is to remove a finished product from the grinding-mill discharge, leaving material that needs further comminution. The classifier, therefore, makes two products: (1) "finished" product, which overflows the rim of the classifier tank, sometimes referred to as "slimes" or as "classifier overflow," and (2) "unfinished" product, which settles to the sloping bottom of the classifier tank and is removed by dragging or raking. This product is generally referred to as "sands" or "oversize." One of the outstanding features of the closed-circuit classifier is its ability automatically to return the unfinished product of the ball-mill discharge to the feed end or scoop box of the ball mill. This is a distinct advantage because it avoids dilution of the ball-mill feed, and, furthermore, the particu1ar method of removing the settled sand, by raking it up the inclined bottom of the classifier, gives a classifier discharge containing a minimum of water. This leads to maximum classifier efficiency, in this type of classifier, because the maximum volume of water is displaced upward by the settling sands. The closed-circuit classifier is required to deliver a finished pulp of closely specified density requirements, therefore added hydraulic water generally is not permitted. Relation of Classifier Efficiency to Grinding Efficiency The energy of crushing, and therefore the cost, according to Rittinger's Law,l is proportional to the new surface exposed in crushing. Since the new surface produced in crushing is nearly proportional to the reciprocals of the diameters crushed to, it is obvious that the cost of crushing in the finer sizes is tremendously greater than in the coarser sizes for equal ratios of reduction. High circulating load of finished sand in the circuit of the classifier and grinding mill is therefore obviously expensive practice. It is the classifier's function to reduce this to a miniMum.

Jan 1, 1930

By J. B. Austin

IT is now well established, chiefly through the work of Davenport and Bain,1 that the influence of temperature upon the rate of transformation of austenite to ferrite at constant temperature is represented by a curve of the type shown in Fig. 5 of Tech. Pub. 589; and the reasons for this general shape have been discussed by them in a qualitative way. Thus, the upper part, or nose, of the curve is the resultant of two factors of which the rate of change with temperature is not the same, and by analogy with other like cases it is almost certain that these factors are: (1) the chemical potential, or driving force, of the transformation, which is zero at the equilibrium temperature and increases rapidly as the temperature falls below this point; and (2) a factor analogous to viscosity, or resistance of the crystal lattice to a change in structure, which also increases as the temperature is lowered. Just below the equilibrium temperature this virtual "viscosity" of the metal is relatively low-that is, the metal offers little resistance to a change in lattice-but the driving force is also small, and the net result is that the reaction proceeds slowly. As the temperature is lowered the magnitude of both factors increases; but at first the driving force increases more rapidly than the resistance and the reaction is observed to proceed more rapidly. At lower temperatures, however, the resistance begins to increase faster than the driving force, and eventually, at the nose of the curve, overbalances it, causing the reaction to proceed more and more slowly thereafter. This concept is somewhat, though not completely, analogous to that employed in certain electrical cases where the precise factors are known and are separately measurable. The current I (in amperes or coulombs per second) flowing through a given wire is proportional to the impressed potential, or driving force E, and is inversely proportional to the resistance R of the wire; that is, I = E/R. Stated in a slightly different way,

Jan 1, 1935

By James A. Barr

PUMICE and pumice are varieties of volcanic ejecta formed from lavas of the more silicic types. Chemical analyses of pumice, pumicite and perlite, from which synthetic pumice is now produced, will generally fall within the limits 65 to 75 pct silica, 9 to 20 pct alumina, less than 8 pct combined alkalies (sodium and potassium oxides), less than 3 pct calcium and magnesium oxide, less than 3 pct iron oxide, with smaller amounts of manganese, titanium, phosphorus and other oxides. Perlite is characterized chemically by having, in addition to the percentages of oxides given above, as high as 6 pct combined water. PROPERTIES Pumice is a natural silicic foam glass produced by volcanic eruptions. The molten glass foam, upon rapid cooling, trapped the steam and volcanic gases that caused it to remain extremely porous and vesicular in structure. Pumice is found in the form of large lumps several cubic feet in volume and also in grains only a few millimeters in diameter. Chemically, pumicite is of the same range of composition as pumice. The distinction between pumice and pumicite is one of particle size; the coarser materials are pumice; the fine particles, an appreciable percentage of which is in the range of 100 to 325-mesh or finer, are pumicite. If the erupting volcano ejects a silicic lava containing much gas and water vapor, the sudden release of pressure tends to free the gas. The viscosity of the lava, its rate of cooling and the amount of gas evolved, all have part in determining the degree of expansion of the glassy particles and the fineness of the vesicle. If the lava is of the correct viscosity and there is not too much gas, a pumice may be formed. Large amounts of gas may cause complete disruption into pumicite.30 In 1916, Barbour gave the name "pumicite" to the volcanic ash of Nebraska and since then the name has been widely used in industrial circles for the finer-grained commercial varieties. The glass of pumice and pumicite is transparent and colorless. It

Jan 1, 1949

By Edward Norton

THE -salt deposits of the Mississippi Embayment region present a problem of origin so genetically related to the larger problem of the stratigraphy and structure of the region that a discussion of the one necessarily involves or assumes an understanding of the other. For this reason, I shall summarize briefly our knowledge of this region, emphasizing the facts related to the subject of this paper. In so doing I shall make liberal use of the reports of the National and State surveys. Geographically that section of the United States known as the Mississippi Embayment region represents a great V-shaped area, extending from near Cairo, Ill., to the Gulf of Mexico, and including Louisiana, eastern Texas, all that part of Arkansas bordering the Ouachita and Ozark mountains, western Tennessee, Mississippi, and a part of Alabama. This great section Professor Harris has described as structurally a pitching trough, its medial line being well represented by the Mississippi River. Outcropping along the border of this area are the Cretaceous and Tertiary formations, unconformably laid down on the hard Paleozoic rock sheets that show more or less plication, deformation, and faulting, depending upon their proximity to the nearby major uplifts. East and west of the Mississippi River the Cretaceous and Tertiary beds dip river- and coastward at angles greater than the slope of the land. "Waters entering along the outcropping edges of the Tertiaries and Cretaceous and following bedding planes southward are soon thousands of feet beneath the surface." As the sedimentation of the region progressed, faulting and slips occurred along planes of pre-Cretaceous weakness. Whether these movements were genetically related to the loading of this V-shaped area, as Professor Harris seems to think, is a question still to be settled. The accompanying map, Fig. 1, was taken from Bulletin No. 7 of the Louisiana Geological Survey. It shows the regional distribution of the salines, as well as an alignment of the domes, which has been assumed to indicate faulting.

Jan 1, 1915

By Edward L. Estabrook

This paper gives a brief account of the geologic and production problems encountered in the Grass Creek oil field, the methods used in their solution, and the beneficial results obtained from the work. The author wishes to acknowledge the assistance received from J. H. Pearson and Miss Ninettta A. Davis in the collection of the data and the preparation of the cross-sections. Permission for its publication was given by the officials of the Midwest Refining Co. and the Ohio Oil Co. The Grass Creek oil field is located in Ts. 98-99 W., R. 46 N., Hot Springs County, Wyo. The productive area includes about 2 1/2 mi. (4 km.) on the apex of a great anticlinal fold occupying more than 150 sq. mi. Fig. 1 shows the structural contours of the field. Oil was dicovered in the field in June, 1914; development proceeded rapidly and production rose to a maximum in 1918. The marketed production has been approximately as follows: Barrels Barrels 1915.................... 94,073.5 1918................... 2,946,774.27 1916................... 1,404,183.97 1919................... 2,000,584.84 1917.................... 2,780,697.51 1920................... 1,485,080.94 About 350 wells, 800 to 1500 ft. (243 to 457 m.) deep, have been drilled to reach the upper oil sands; two companies, the Ohio Oil Co. and the Midwest Refining Co., operate the entire field. The principal producing sands in the field are members of the Frontier Formation, a series of sands and shales occuring in the upper portion of the Colorado Group of the Upper Cretaceous seriee. These Frontier, or "Wall Creek" sands are also productive in the Salt Creek, Big Muddy, and Elk Basin fields and, therefore, are much the most important reservoirs of light oil in Wyoming. At Grass Creek, the sands in the Formation are more numerous than in the other fields and much less uniform in thickness and character. Usually, eight distinct beds are encountered and in some wells twelve sands have been reported. The formation above

Jan 1, 1923

By J. H. Nead

The subject of this paper is one to which there are many references in the literature on the manufacture of steel in the open-hearth furnace, but few actual experimental data have been published. For that reason, the presentation of results obtained from two open-hearth heats where attempts were made to measure the sulfur absorption will be of considerable interest and value. The two heats on which the experiments were made were Armco ingot-iron heats and differ from the usual open-hearth heat of medium- or mild-carbon steel in that the refining is carried further; in this product the carbon and manganese are reduced practically to traces. In most other respects, and especially in respect to the absorption of sulfur from the producer gas, the two heats are typical of usual open-hearth practice. The object of the experiments made on the first Armco iron heat was to determine the fluctuation of the composition of the metal bath and the slag throughout the course of the heat, with especial reference to the variations in sulfur. It was hoped to determine whether there was an increase in sulfur in the bath from the producer gas and if so at what stage in the process the increase occurred. The experimental method consisted of charging analyzed scrap and pig iron, so that the sulfur in the charge could be calculated. Then, throughout the duration of the heat, metal and slag samples were takcn every half hour, beginning as soon as there was enough molten metal to take a sample. These samples were analyzed; the results are given in Table 1. All domestic scrap was used and the charge was made up as follows: Head End Finish Pounds Pound Pig iron........................ 36,300 Pig iron....................... 23,900 Sheet scrap bundles............. 36,200 Sheet bars..................... 23,900 Sheet bm..................... 40;200 The total charge, exclusive of the re-pig added near the end of the heat, was 160,500 Ib. The limestone charged was 21,400 Ib., or 13½ per cent.

Jan 1, 1924

By R. A. Bowen

THE Montreal mine, operated by the Montreal Mining Co., is four miles west of Ironwood, Mich., in Iron County, Wisconsin. It is the westernmost producing property on the Gogebic Iron Range of the Lake Superior district. Its production is 4000 tons of hematite per day from an average depth of 2300 ft. This tonnage is hoisted through a five-compartment vertical shaft. Several mining methods are in use but in the larger orebodies the method is sublcvel caving. ORE OCCURRENCE AND CHARATERISTICS The main orebodies of the Montreal mine lie in eastward-pitching troughs formed by the intersections of intrusive dikes with impervious members of the iron formation. The formation has an average width of 425 ft., strikes east and west and dips north at approximately 62°. The dikes dip south at 45° and bear north 20° from the strike of the formation, making the intersections with various members pitch east at 16°. The dikes are not continuous across the formation but are interrupted by a longitudinal bedding fault, which has a throw of 380 ft. vertically and 885 ft. horizontally. North of the fault zone the formation is called "hanging," south it is called " footwall" formation. The faulting has created two ore-bearing horizons; viz., at the inter- section of hanging dikes with the slate members and the foot dikes with the quartzite footwall. In each formation the main ore-bearing member consists of wavy beds of hard chert interlaid with hematite. In the most productive part of the mine, where the sublevel caving method is employed, a hanging-formation dike lies in juxtaposition with a footwall dike and the iron formation carries ore in certain sections from the quartzite footwall to the hanging dike. Here a horizontal section of the orebody may be 300 to 400 ft. wide for a length of 150 ft. or more and tail out lengthwise in both the foot and hanging formations. The footwall ore section is much longer than the hanging wall because of the orebody's greater height above the "pitching dike."

Jan 1, 1938

By J. Morgan Clements

The manufacture of coke in Peru, as practiced at the coalmines of the Quishuarcancha and Goyllarisquisca districts, is intermediate between the primitive coke-heap and the bee-hive oven. The method of coking is quite simple. In constructing the coal-heap, preparatory to burning, the ground is first leveled, and a simple stack of stone and clay is built, giving the bottom, to a height of 6 ft., approximately 6 ft. of external diameter. The size of the stack varies in different districts, but is generally 9 ft. high, and slightly smaller at the top than at the bottom. The walls of the heap are from 12 to 14 in. thick, which allows an inside diameter of from 3.75 to 4 ft. These walls are pierced at intervals by three or more tiers of openings or flues, connected with the central flue. The radial flues have a diameter of about 5 in. and are built with a gentle upward slope. The stack (shown in Fig. 1) is permanent; and in this respect the practice in Peru differs from other primitive practices in which nothing is permanent except the yard. Above the permanent 6-ft. portion of the stack there is added a cap of clay, about 3 ft. high, which contracts toward the top, where it has an inside diameter of about 2 ft. This clay cap is temporary, and frequently has to be renewed after each burning. Before charging the coal, there are first built, from the lowest tier of flues upon the ground, a number of temporary flues, leading from the central stack out to the edge of the coal-heap, and constructed of blocks of coal for the greater part of the distauce, the outer edge alone being of rough stoue. The coal is then piled up over these flues and around the stack to a height of about 6 ft. The bottom flues are the only ones that

Jan 1, 1905

By W. H. Ode, W. A. Selvig

By plotting fixed carbon against British thermal units of coals free from mineral matter, and ranging in rank from anthracite to lignite, it is found that the coals of higher rank, from anthracite to the higher rank of the high-volatile bituminous coals, inclusive, can be separated into groups according to their degree of metamorphism by reference to their fixed carbon. Such charts show also that the coals lower in rank can be best separated into groups with respect to B.t.u., especially when plotted on the moist basis, that is, coal containing its natural bed moisture. A tentative scheme for coal classification was presented at the October, 1932, meeting of the Technical Committee on Scientific Classification, of the American Standards Association Sectional Committee on Coal Classification. This scheme was sponsored by Subcommittee IV on Tentative Classification of Coals, under the chairmanship of W. T. Thom, Jr. It proposed the grouping of coals according to rank by reference to fixed carbon and B.t.u., on the basis of coal containing its natural bed moisture but free from mineral matter. This scheme proposed classifying coals into four broad classes: (1) anthracitic, (2) bituminous, (3) subbituminous, (4) lignitic. The anthracitic class was divided into three groups designated as meta-anthracite, normal anthracite, and semianthracite. The bituminous class also was divided into three groups, low volatile, medium volatile, and high volatile. The high-volatile group was further subdivided into four subgroups according to moisture content, as fo1lows: (1) less than 5 per cent, (2) 5 to 10 per cent, (3) 10 to 15 per cent, and (4) 15 per cent and more. The subbituminous class was divided into two groups, group 1 including subbituminous coals having calorific values of 10,500 B.t.u. or more, and group 2 including those with less than 10,500 B.t.u. The lignitic class of coal was divided into two groups both below 8,000 B.t.u., the one group consisting of consolidated and the other of unconsolidated

Jan 1, 1934