Search Documents

By M. von Heimendahl, G. Thomas

The microstructure of TD-Ni has been examined by transmission electron microscopy in the extruded, annealed. and deformed states. The tensile properties hove been correlated with the observed microstructures and the results ore com-pared with those obtained from pure nickel. The important conclusions are that the thorin particles in TD-Ni act as strong burriers to dislocntion motion during both deformation (slip) and annealing (climb). During deformation. the dislocations tangle around the particles and a cell structure is devleloped after 10 pct or more strain. The cell size appears to be determined by the spacing of the largest particles and is about five times smaller than that in pure nickel for the same strain. The higher work-hardening rate in TD-Ni compared to nickel is probably due to the more rapid rate of dislocation multiplication in the alloy as a result of dislocation-particle interactions. The Th0,particles inhibit recrystallization and twin growh so that some strengthening may arise from the high density of small annealing twins. THE strengthening of materials due to the presence of a dispersed second phase has been the subject of considerable experimental and theoretical investigation in recent years. One of the newest dispersion-strengthened alloys to be developed is TD-Ni,1 a system of approximately 2 vol pct thoria (ThO2) dispersed in a matrix of commercially pure nickel. This material is fabricated by powder-metallurgical techniques and offers high-temperature stability and useful mechanical properties virtually to the melting point of the base metal. While the mechanical properties of this system have been investigated,2,3 there have been no reports in the literature concerning the microstruc-ture of TD-Ni and its correlation to mechanical properties. This paper describes a transmission electron microscopy investigation of the micro-structure of TD-Ni together with its mechanical properties. The results are compared with the structure and properties of pure nickel.

Jan 1, 1964

By Zay Jeffries

THIS paper will include a brief discussion of Prof. Howe's paper on The Supposed Reversal of Inheritance of Ferrite Grain Size from that of Austenite.1 The general subject of grain refining in steel and iron will also be treated. The conclusions reached are stated in the following hypotheses which are discussed more in detail below. 1. The ferrite grain size in pure iron, the ferrite and pearlite grain size in hypoeutectoid steel, the pearlite grain size in eutectoid steel and the cementite and pearlite grain size of hypereutectoid steel are not inherited from the grain size of the mother austenite. 2. The only structural feature that is generally inherited from the austenite of hypo- and hypereutectoid steels on cooling through their transformation ranges is the position of the excess ferrite or cementite at the austenite grain boundaries, sometimes causing complete and sometimes incomplete networks which outline the old austenite grain boundaries. Rapid cooling through the transformation range will cause the non-inheritance of this structural (network) feature. 3. The austenite grain boundaries themselves are nearly always effaced in all steels and also in pure iron during the Ar transformations. 4. The grain-size refining of steel and iron is brought about by the combined. effect of non-inheritance of the transformation products on either heating or cooling, i.e., the austenite transformation .products do not inherit their grain size from the austenite on cooling through the transformation range for does austenite inherit its grain size from the products which form austenite on heating. 5. In general, in both iron and carbon steel the larger the austenite ,grain size, the larger will be the grain size of the transformation products on cooling. This, of course, assumes all other conditions constant except the austenite grain size. An exception is found to this general rule in very pure iron such as electrolytic iron. 1n this instance small austenite grains may form very large ferrite grains on cooling through Ar3.

Jan 11, 1917

By Richard L. Gordon

THE PROBLEMS AND POSSIBLE SOLUTIONS Toward the end of the 19th century, American industry began a drastic reorganization. The many, small, often-regional firms were supplanted by large national corporations-often produced by mergers among the existing firms. Giant companies appeared throughout American industry and many of them were engaged in the mineral industries.a The largest combines, by far, to emerge during the period were United States Steel and Standard Oil. Long before the restructuring had run its course, widespread concern arose over the process of concentration. Efforts were made to control, if not stop, the transformation. The concern produced the Sherman Antitrust Act of 1890 and the first of many federal regulatory agencies-the Interstate Commerce Commission (see Refs. 24, 31, 42). The basic objectives of these policies remain unclear to this day. The crucial issue is whether the goal is primarily to insure development of a more competitive economy or to preserve a social structure leaving more scope for small businesses. Complications arise from difficulties in agreeing upon the meaning of these terms. Studies of the early years of the antitrust movement suggest that it involved no particular concern over the mineral industries. Objections were directed at big companies in general. To be sure, the conservation movement arose in roughly the same period and did stress the evils of monopoly control of minerals. However, direct, continuing influence of conservation policy on antitrust is not apparent. Many of the most important antitrust cases, nevertheless, involved minerals. This, of course, may be sheer coincidence; the choice of cases has never followed any obvious pattern. Certainly, no simple hypothesis can explain the interest consistently. Once it may have been true that mineral industries were more likely than other sectors to be dominated by a few large companies. Yet, often sharp reversals of such tendencies -e.g., in oil and aluminum-have not removed antitrust interest. The importance of minerals to the economy cannot satisfactorily rationalize antitrust interest. The equally

Jan 1, 1976

IN the preceding chapter on thermochemistry and the reactions in and between metal and slag phases and in the following chapter on fuel combustion the main emphasis is placed on the equilibrium or "static" conditions. This equilibrium viewpoint is not concerned with the rate of change in the process or with the mechanisms or paths followed between initial and final states. The questions of just "how it works" and "how fast" belong to the kinetic aspect of any process; their answers are helpful in speeding up or slowing down and thus controlling its operation, and also in understanding its limitations. Any treatment of kinetic factors in the open hearth such as is attempted here and in Chapter 22 must at present be largely qualitative and incomplete. We are only beginning to get quantitative data on rates of reaction and diffusion at high temperatures, as indicated in Chapter 15. Empirical data in the literature on furnace operating rates do not help much to illuminate the details of gas-flow patterns and the complexities of heat flow in the many parts of the furnace system. This chapter is intended to give the reader an introduction to the problems of the flow of gases through the furnace system and the flow of heat in this system. An adequate discussion would require several times the space available here; it is possible here only to outline a few fundamentals and to indicate some of the conditions of heat and gas flow peculiar to the open hearth. Several good general treatments of these subjects may be found in the literature (see references at the end of the chapter). For the designer of open-hearth furnaces, the principles of gas flow are of paramount importance. They are also important to the operation of the process, at least to the extent of a general qualitative picture of the movement of gases in the system. MOTION OF GASES IN FURNACE DUCTS Fluid flow in general can vary between the extremes of laminar or streamline flow with a minimum energy loss, to irregular

Jan 1, 1951

By Charles Morgan

AN increased demand for brown iron ore in the Birmingham district during the past 18 months has caused renewed activity both in prospecting and mining these ores. In recent years the production in Alabama has ranged from 41,559 tons in 1932 to 639,351 tons in 1928. During the last 9 years about 83 per cent of the total brown ore produced in the United States has come from Alabama (Tables 1 and 2). PROSPECTING Two methods of prospecting are used in this district: (1) test pits, (2) churn-drilling. Usually there is certain quite definite information on an area to be prospected; some of the indications are float ore suck as small gravel or small and large boulders known as "dornicks” scattered over the surface, and ore exposed by erosion in gulleys and ravines, which have cut or eroded through the overburden. Often these natural erosions furnish an indication of the thickness of the ore and to some extent of the area of the ore body. Deposits of brown ore are very irregular both in thickness and extent. Deposits are often lens-shaped or long narrow leads, some of which may be parallel and separated from one another by sand, clay or gravel. The bottom-the footwall-is also very irregular. This footwall is usually lime clay-disintegrated limestone, locally called "white horse," which usually is found at a depth of 6 in. to 20 ft. overlying the limestone. At some places sand and gravel is found under the ore instead of clay. No ore is found under the lime clay, although often the ore has sunk or slumped and is found in the upper portion of this clay, as at some of the Sloss workings at Russellville. The origin of these ores has been discussed by Major E. C. Eckel and Dr. E. F. Burchard in U. S. Geological Survey Bulletin 400, and recently the latter has done further work on ores in the Russellville district, of which reports undoubtedly will be published.

Jan 1, 1937

By Charles Morgan

An increased demand for brown iron ore in the Birmingham district during the past 18 months has caused renewed activity both in prospecting and mining these ores. In recent years the production in Alabama has ranged from 41,559 tons in 1932 to 639,351 tons in 1928. During the last 9 years about 83 per cent of the total brown ore produced in the United States has come from Alabama (Tables 1 and 2). Prospecting Two methods of prospecting are used in this district: (1) test pits, (2) churn-drilling. Usually there is certain quite definite information on an area to be prospected; some of the indications are float ore such as small gravel or small and large boulders known as "dornicks" scattered over the surface, and ore exposed by erosion in gulleys and ravines, which have cut or eroded through the overburden. Often these natural erosions furnish an indication of the thickness of the ore and to some extent of the area of the ore body. Deposits of brown ore are very irregular both in thickness and extent. Deposits are often lens-shaped or long narrow leads, some of which may be parallel and separated from one another by sand, clay or gravel. The bottom—the footwall—is also very irregular. This footwall is usually lime clay—disintegrated limestone, locally called "white horse," which usually is found at a depth of 6 in. to 20 ft. overlying the limestone. At some places sand and gravel is found under the ore instead of clay. No ore is found under the lime clay, although often the ore has sunk or slumped and is found in the upper portion of this clay, as at some of the Sloss workings at Russellville. The origin of these ores has been discussed by Major E. C. Eckel and Dr. E. F. Burchard in U. S. Geological Survey Bulletin 400, and recently the latter has done further work on ores in the Russellville district, of which reports undoubtedly will be published.

Jan 1, 1940

By E. von Maltitz

In his highly interesting paper, Piping and Segregation in Steel Ingots,' Prof. Howe emphasizes the effect of successive phases of internal pressure in the ingot in the evolution of gas, and the consequent formation of blow-holes. From his statements in other places, it may be inferred that he does not here intend to ignore the other variable factor, temperature, but rather to discuss this one more particularly. At all events, it is my purpose not to engage in controversy with Prof. Howe, but, rather to contribute, towards the complete elucidation of this important subject which we all desire, my own views and experience. If, in doing so, I specially emphasize other factors than pressure, I need not be understood as denying what I do not think it necessary to discuss fully. Nor, in presenting my own original conclusions, need I be understood as claiming to be the first who ever reached or announced them. Many things are asserted or suggested upon inconclusive evidence; and to confirm such tentative propositions may be as valuable a service as to overthrow them. In the following passage, Prof. Howe adduces analogies, based upon the behavior of charcoal and of water, respectively, which seem to me questionable : "In general, the solvent power falls as the pressure falls ; and in general it rises as the temperature falls. Thus, to heat a solid, for instance charcoal, may expel part of its dissolved gas ; and a tumbler of water drawn cold from the faucet gradually evolves gas, as it stands and warms up on the sideboard." (p. 72.) Charcoal is a solid body, which has the property not only of absorbing gases in large quantities, but also of expelling the thus absorbed gases upon heating. A comparison between charcoal and iron as to the absorption of gases is scientifically not possible; the gas-content of charcoal is partly due to the

Jan 1, 1908

THE problem of reaction rates in the open-hearth process is essentially that of trying to form a fairly clear picture of the "chemical mechanisms" in the bath. Quantitative data on reaction rates would perhaps not be of much practical importance even if they were available; however, what few approximate data there are can be used in combination with data given in Chapters 16 and 17 to sketch a picture of the "chemical mechanics" of the open-hearth process that is consistent with essentially all the present available evidence. The result may later be found incorrect in many details but even so it will illustrate certain useful methods for obtaining a clearer understanding of the process. Consistent with the treatment in Chapter 15, but in simpler terms, we may say that chemical reactions in general involve the following elements or steps : 1. The reacting molecules are mixed together in space in such fashion as to favor collisions among them. 2. Units of what is usually an intermediate molecular arrangement called an activated complex are formed at a certain rate, depending on temperature and concentrations. 3. .These activated complex units decompose into the reaction products (this step usually assumed to be so rapid as never to limit the over-all process). 4. In any of these steps, heat energy may have to flow into, or away from, the reaction zone to permit the reaction to proceed. 5. The products of reaction will usually have to move out of the way to permit further reaction. The temperature factor enters mainly through step 2, and its effect is very marked. (What is called temperature is really the mean energy content of all the molecules of the substance involved; at any one temperature a certain proportion of the molecules will have much higher energy content than the mean value.) Various reaction rates measured at around room tem-

Jan 1, 1964

By J. B. Morrow

WITH numerous plans under consideration for coal classification, and with the advent of the Bituminous Coal Code, the intelligent sam-pling of coal has become increasingly important. To us it is rather significant that there have been very few fundamental studies of coal sampling in American technical literature since those of E. G. Bailey, which appeared in the Journal of Industrial and Engineering Chemistry in March, 1909. He covered the subject up to that time so thoroughly and in such an excellent manner that perhaps many other later students have felt that they could add very little to his findings. The recent studies of the British Engineering Standards Association have indicated the possibility of a somewhat different interpretation of Bailey's results, permitting the taking of smaller samples, and perhaps it will now be helpful to reopen this question. C. W. H. Holmes, in an informative series of articles on coal sampling recently published in Colliery Engineering, makes two rather interesting statements, as follows: It is scarcely surprising to find a lack of interest and knowledge regarding the sampling of coal not only in the mining industry itself but also among consumers of industrial fuel: at its best coal sampling is a dirty business, regarded as a nuisance and an expense by the commercial man, and usually as a nuisance and nothing else by the chemist. The writer can conceive only two classes of people who have never experienced any difficulty in obtaining representative samples of coal from wagons; those who have never tried to, and those who have never had the necessity or desire to check the accuracy of their work. The primary purpose of this paper is to present some tabulated data of the more significant results of a sampling investigation undertaken during the last four years to obtain certain fundamental data on the variables connected with coal sampling and to point out that often assumptions have been made that are not in accordance with the facts. One of the standard sampling methods states:

Jan 1, 1935

By A. B. Cox, L. W. Wark

An attempt has been made to compare the influences of the two most widely used depressants—alkalis and sodium cyanide—and the most widely used activator—copper sulfate—on the air-mineral contact induced by five sulfur-bearing compounds: (1) sodium di-ethyl dithio-phosphate (sodium Aerofloat); (2) potassium ethyl xanthate; (3) sodium di-ethyl dithiocarbamate; (4) potassium iso-amyl xanthate; (5) potassium di-n-amyl dithiocarbamate. Three different organic types are included in lhis group and for two of these types a higher and a lower homologue have been tested. The study of potassium ethyl xanthate, the preliminary results of which have been described,' was continued until there had been obtained a comprehensive account of the influence of variations in pH value and in the concentrations of xanthate, sodium cyanide and copper sulfate on the adsorption of this xanthate by galena, sphalerite, pyrite and chalcopyrite. With concentrations of copper sulfate and collector that the work with ethyl xanthate indicated would give the most illuminating. results, the other four collectors were tested, in a less exhaustive way. The same general principles determine the influence of alkalis, cyanide and copper sulfate, no matter to which type the collector belongs, but there is a gradation in the quantitative measure of such influence. In the list above, the five collectors are cited in the order of their capacity to withstand the depressants, sodium Aerofloat being the least resistant, potassium di-n-amyl dithiocarbamate the most resistant. This order coincides substantially with that of the solubilities of the heavy metal salts formed by double decomposition with the collectors, those formed from sodium Aerofloat being most soluble. There is little difference between the third and fourth members of the series, and under certain conditions their positions are reversed. In general, then, of the three types of collectors investigated, the dithiophosphate type is most easily influenced by depressants, and the

Jan 1, 1935

By F. Osmond

When a metal (whether a simple substance, an alloy, or a compound) presents, in each of the smallest parts to which it can be redueed by mechanical division, a constant chemical composition, it is defined as chemically homogeneous. But chemical hombgeneity by no means necessitates mechanical homogeneity. There are no perfectly amorphous metals. Crystalline forces, on the one hand, and tensions or compressions, on the other band, determined by icequalities of temperature in the mass during heating or cooling, give rise in every metal to the formation of geometric elements of structure. These elements may, moreover, assume perfect crystalline forms, with their planes of cleavage; or embryonic crystalline forms, segregated in the midst of. a paste of confused organization; or pseudo-crystalline forms of expansion and contraction, like those produced in the drying of gelatinous precipitates or (most frequently) these different forms associated. 111 either case the adhesions between two adjoining structural elements, respectively homogeneous, may be very different from the interior cohesion of each of these elements. The mechanical properties of this complex aggregate cannot be simple, and, when it is submitted to strains sufficient to produce deformation, the results may be very different according to the type of structure or the manner in which it is affected by the strains. It may be fairly said that a metal does not present a single resistance to tension, or a single resistance to compression, etc., but in fact, at least theoretically, as many resistances to tension, compression, etc., as it may possess coexistent features of structure; only, in any single test, it is the weakest of the resistances involved which makes itself evident. For further explanation, let us imagine a cylinder A B (Fig. I), formed of two similar halves A and B, placed together upon their common base x y. Such a system evidently presents no resistance to axial tension, while it would resist axial compression like a single

Jan 1, 1894

THE problem of reaction rates in the open-hearth process is essentially that of trying to form a fairly clear picture of the "chemical mechanisms" in the bath. Quantitative data on reaction rates would perhaps not be of much practical importance even if they were available; however, what few approximate data there are can be used in combination with data given in Chapters 16 and 17 to sketch a picture of the "chemical mechanics" of the open-hearth process that is consistent with essentially all the present available evidence. The result may later be found incorrect in many details but even so it will illustrate certain useful methods for obtaining a clearer understanding of the process. Consistent with the treatment in Chapter 15, but in simpler terms, we may say that chemical reactions in general involve the following elements or steps: 1. The reacting molecules are mixed together in space in such fashion as to favor collisions among them. 2. Units of what is usually an intermediate molecular arrangement called an activated complex are formed at a certain rate, depending on temperature and concentrations. 3. These activated complex units decompose into the reaction products (this step usually assumed to be so rapid as never to limit the over-all process). 4. In any of these steps, heat energy may have to flow into, or away from, the reaction zone to permit the reaction to proceed. 5. The products of reaction will usually have to move out of the way to permit further reaction. The temperature factor enters mainly through step 2, and its effect is very marked. (What is called temperature is really the mean energy content of all the molecules of the substance involved; at any one temperature a certain proportion of the moleculea will have much higher energy content than the mean value.) Various reaction rates measured at around room tem-

Jan 1, 1951

By American Institute of Mining Engineers

David J. Mack (University of Wisconsin, Madison, Wise.)—Have the authors considered that the effects reported in their paper are readily explainable on the basis of equilibrium grain boundary segregation rather than ordering? It seems to the writer that all of their experiments and observations correlate well with known behavior associated with equilibrium grain boundary segregation. Although at first glance one would tend to dismiss such a possibility because of the similarity of the gold and copper atoms, their sizes differ by 12.8 pct which is in the range where segregation at grain boundaries would be expected. Then, too, the electrochemical differences between the copper, the Cu3Au, and the gold strongly suggest that a segregation mechanism is involved in the corrosion of the Cu-Au alloys. R. Bakish and W. D. Robertson (authors' reply)—The authors would like to thank Dr. Mack for his consideration of the problem of grain boundary segregation as an explanation of the observed phenomena. We had considered the problem in the following terms: Assuming a pure binary Cu-Au alloy and an ideal solid solution, the surface excess, T2= N25 — N2, of the second component (gold) may be expressed in the following way20 1 —exp (—da/kT) where 8 is the difference in surface tension of copper and gold, and a is the surface area per atom. In the present case, 6 is positive which implies that the component in excess at the boundary is gold. Since the only chemically active component in ferric chloride is copper, it does not appear that the segregation of gold is likely to increase the boundary activity. A small concentration of a third component could profoundly affect the situation. Analysis indicated only spectrographic traces of impurities, all of which are soluble in both copper and gold. Quenching experiments, reported in the paper, also tended to eliminate significant effects attributable to a third component.

Jan 1, 1958

By F. W. Apgar

THe valuable results that have followed the application in recent years of microscopic methods of research to problems of ore genesis have been significant, but possibly the recognition of their practical importance is not as general as might be, and while, as a scientific method of investigating ores and rocks, the advantage derived through the use of the microscope is unquestioned, its utility as an aid in solving mining problems arising during actual every-day mine examination and operation may not be fully appreciated. Perhaps the most logical method of showing some of these practical applications of the microscope will be to consider first the prospect stage of a mining venture, then the uses to which the instrument may be put during the operation of a working and developed mine, arid, finally, to discuss some of the problems of a metallurgical nature that may arise during milling and smelting the ore. The valuation of mining property as a preliminary to acquiring ownership or determining the advisability of investing time and money in an enterprise is one of the most important and delicate problems that come before the mining engineer. The many and variable factors that have to be taken into account, as, for example, the geology of the district, availability of supplies, probable mining costs, transportation facilities, and the quality of ore, require a careful balancing of costs against recoverable values. Primarily, however, a study of the local geology is of first importance, since, in a prospect with little development work, the question of character and probable quantity of the ore and its value can only be approximated with any degree of accuracy by a thorough investigation of geologic conditions, and a general knowledge of ore deposits. Unless these are favorable and pay ore reasonably certain, other factors need not be considered. The character of the outcrop, evidences of mineralizing agencies in the adjacent rocks, and geological structure, are the data of chief significance.

Jan 1, 1914

By W. H. Emmons

MOST mineral deposits change as they are followed downward on their dips. Some of these changes are due to primary arrangement; different ores were precipitated at different depths when the deposits were formed. Other changes are due to weathering or secondary enrichment. The chief changes resulting from weathering, in the main, are understood and standard changes are recognized. The processes are relatively simple. They take place at ordinary temperatures and pressures and can be duplicated in the laboratories. Moreover, there are thousands of deposits available for study, because the processes take place near the surface where the development of mines is begun. The changes due to primary arrangement of the deposits of the metals are not so well understood. Deposition has taken place at higher temperatures and our knowledge of the chemistry of the processes leaves much to be desired. Very few experimental data are available. The deposits, moreover, offer fewer examples because many mines are not, developed to depths where the changes can be studied and a change to unprofitable material usually results in stopping work. Most, students of ore deposits now accept, as confirmed, the hypothesis that nearly all lodes and related deposits were formed by solutions originating in intrusive igneous masses. Outward from these masses, the deposits at many places are grouped in zones and the arrangement noted from the intrusions outward are commonly the reverse of the changes noted from the surface downward in a single lode. A study of the changes in groups of deposits, from the parent intrusion outward, will throw light on the changes to be expected in a single lode downward. Because the changes in series of deposits from the intrusive outward may all be observed near the surface, where more data are available, it is possible to increase the number of examples many fold and to apply the statistical method of study with greater confidence of avoiding error.

Jan 3, 1924

By I. R. Kramer

Single crystals of aluminum were pulled in tension in a solution of paraffin oil and stearic acid. The critical resolved shear stress did not change with the concentration of the stearic acid solution; however, the extents and slopes of Stages I and II were affected greatly. The observations lend evidence that the weakening effect of surface-active agents is controlled by the rate of desorption of the metal soap formed by the reaction of the surface-active agent and the metal surface. IT has been shown by various investigators1-" that surface-active agents markedly affect the mechanical properties of single crystals. (A surface-active agent, for the purpose of this report, is defined as a long-chain organic molecule which contains one or more polar groups. Usually, however, investigations have considered only molecules having one polar group.) In general, when single crystals are deformed in some solutions containing surface-active agents, the creep rate, Fig. 1, is increased and the yield strength is decreased. The fatigue strength has been reported to be affected also.ll Rehbinder and his asociatesl' explained the "weakening" effect of surface-active agents in terms of physical adsorption. They assumed that a large pressure was created in microcracks which existed on the surface of the crystal." Harper and Cottrell,' from their study of the effects of surface conditions, found that the deformation characteristics of zinc single crystals were not altered by a solution containing a surface-active agent unless the surface of the specimen had an oxidized surface. They concluded that the role of the polar molecule was to remove the strengthening effect of the oxide coating. Later, And-radeetBpresented additional evidence which appeared to agree with this conclusion. In contrast, Klinken-berg et al.7 reported data which confirmed the results of Rehbinder. Using zinc and cadmium crystals which had been cleaned by electrolytic polishing, a large increase in the creep rate was observed when Lle specimens were tested in a 1 pct oleic acid-paraffin oil solution. They also reported that the creep rate

Jan 1, 1962

By E. S. Grumell

The correct sampling of coal and coke is becoming important to an ever increasing number of producers and consumers. This, therefore, may be an opportune moment to examine where we stand with regard to existing and proposed methods. In this paper an attempt will be made to review, as briefly as possible, some of the considerable amount of painstaking research which has been done in the last 10 years, and which has unquestionably led to a much better understanding of the subject. In so doing we shall try, on the one hand, to make clear where substantial progress has been made, and on the other hand, to draw attention to points that require further investigation. The paper is divided into sections in order to emphasize the major divisions of the subject; further, in order to retain this emphasis, detailed consideration of some of the points has been relegated to appendixes. No attempt has been made to give a complete survey of the literature, as this has already been done by L. A. Bushell.2 The following abbreviations will be used: A.E., average error; P.E., probable error; S.W.R., size-weight ratio; B.S.I., British Standards Institution. Section 1.—Cost It has often been stated that the cost of sampling should bear some relationship to the value of the product, and since coal is a relatively cheap raw material it would be a major error to specify, for ordinary commercial purposes, elaborate and costly methods of sampling which nobody would adopt. Specifications must be of such a nature that they will be used. We believe that one of the achievements of the last 10 years has been to reduce the cost of sampling. There is, however, another point to be considered; via., that the cost of sampling should bear some relationship to the value of the investigation. Correct sampling is a cog (possibly a small one) in the wheel

Jan 1, 1940

By C. P. Proctor, J. B. Morrow

With numerous plans under consideration for coal classification, and with the advent of the Bituminous Coal Code, the intelligent sampling of coal has become increasingly important. To us it is rather significant that there have been very few fundamental studies of coal sampling in American technical literature since those of E. G. Bailey, which appeared in the Journal of Industrial and Engineering Chemistry in March, 1909. He covered the subject up to that time so thoroughly and in such an excellent manner that perhaps many other later students have felt that they could add very little to his findings. The recent studies of the British Engineering Standards Association have indicated the possibility of a somewhat different interpretation of Bailey's results, permitting the taking of smaller samples, and perhaps it will now be helpful to reopen this question. C. W. H. Holmes, in an informative series of articles on coal sampling recently published in Colliery Engineering, makes two rather interesting statements, as follows: It is scarcely surprising to find a lack of interest and knowledge regarding the sampling of coal not only in the mining industry itself but also among consumers of industrial fuel: at its best coal sampling is a dirty business, regarded as a nuisance and an expense by the commercial man, and usually as a nuisance and nothing else by the chemist. The writer can conceive only two classes of people who have never experienced any difficulty in obtaining representative samples of coal from wagons; those who have never tried to, and those who have never had the necessity or desire to check the accuracy of their work. The primary purpose of this paper is to present some tabulated data of the more significant results of a sampling investigation undertaken during the last four years to obtain certain fundamental data on the variables connected with coal sampling and to point out that often assumptions have been made that are not in accordance with the facts. One of the standard sampling methods states:

Jan 1, 1936

By Cyril Wells, Robert F. Mehl

The diffusion of carbon in gamma iron plays an essential role in many metallurgical processes. In carburizing, in graphitizing, in homogenizing, in the formation of pearlite from austenite, and in other processes, migration of carbon in gamma iron occurs.1'2 A full understanding of the rate at which these processes occur obviously requires a knowledge of the rate of diffusion of carbon. In carburizing, for example, the depth of carbon pentration is determined by the carbon concentration in solid solution at the surface, and by the rate of diffusion inward of the carbon. Until reliable data on the rates of diffusion of carbon are available it is unlikely that a full quantitative description of this process will be obtained. In the formation of pearlite from austenite, the segregation of carbon and alpha iron from the austenite obviously requires the diffusion of carbon; the rate at which pearlite nodules grow is evidently controlled at least in part by the rate of diffusion of carbon; it is unlikely that we shall understand the factors that determine the rate of growth unless data on rates of diffusion of carbon, and the variation of these with composition, grain size, and temperature are available. Accordingly it was decided: (1) to determine, more accurately than hitherto, the diffusion coefficients of carbon in austenite over a wide temperature and a wide concentration range, (2) to study the influence of grain size and impurities on this diffusion coefficient, and (3) to study the effect of manganese and nickel on the rate of diffusion of carbon in the austenite of manganese and nickel steels, respectively; the influence of carbon on the rate of diffusion of manganese and of nickel will be made the subject of later papers. The rate of diffusion of carbon in gamma iron has been studied by Runge3 by Tammann and Schonert4, by Bramley and co-authors,5-14 and

Jan 1, 1940

By George A. Moore, Donald P. Smith

In spite of many investigations of the occlusion of hydrogen in iron, the nature of the process and the reasons for the accompanying effects upon the metal are still open questions. This is in large part due to three causes: (1) the difficulty of obtaining iron of adequate purity as starting material; (2) the occurrence of allotropic transformations, which complicate the effects; and (3) the fact that the body-centered cubic modification does not lend itself readily to crystallographic investigation. The present paper attempts a critical review and correlation of the somewhat scattered and disconnected existing observations, and an experimental determination of the extent to which the conclusions that appear to follow from these are applicable to iron of really high purity, studied under well-defined conditions. Review Although only a comparatively few investigations have so far been made on the pure system iron-hydrogen, there is a much larger volume of literature which throws some light on the problem but falls short of a place in the systematic investigations, either because no attempt was made to measure equilibrium conditions or because the metal used was not iron or the gas not pure hydrogen. Such results have been variously dismissed in the past as of no importance, or as too complicated to try to explain; or they have been explained in terms of any of a dozen or more pictures, each of which is contradicted by data from other sources. The present importance of these data thus arises from their very mass and diversity, which present a picture of occlusion as a phenomenon whose variability cannot be ignored. We have attempted to organize the literature into groups comprising similar experiments or data leading to similar conclusions, thus of necessity sacrificing accuracy of historical order. Lattice Occlusion.—Throughout this discussion, the term "lattice occlusion" will be used to denote the formation of a simple solid solution of a gas in a metal lattice, usually of interstitial distribution. The word

Jan 1, 1939