Search Documents

By A. T. Beckwith

THE Lehigh Navigation Coal Company Inc. operates steep-pitch, relatively deep mines in the Panther Creek Valley, at the eastern end of the southern anthracite coal field. Commercially minable coal beds are the Mammoth,† Primrose, Orchard, and Buck Mountain,‡ their respective thicknesses average 50, 15, 1o and 12 ft. Sand slates immediately overlie and underlie these beds, though in some locations sandstone or conglomerate beds occur. Underground operations extend to a depth of 1200 ft. below the surface, and comprise a bulk of virgin work on the lower levels, and a small amount of remining on the upper levels. With increase in depth, ventilation has become a more important factor. DEVELOPMENT In early days slopes or drifts were driven in the outcropping coal on the hillsides. Subsequent development was by water-level tunnels, with portals above high water in Panther Creek. These tunnels have been maintained because they intercept and drain much water that enters the mined-out portion of the bed and otherwise would follow down to the deep workings. Below these tunnels, the coal was customarily developed by slopes. Muleways, which are zigzag chutes easy to travel, were also driven to connect lower openings with the water levels. When it became necessary to go still deeper, the slopes were abandoned, and vertical multicompartment shafts were sunk from the surface. Levels have been at vertical intervals of from 195 to 250 ft. Recent practice has been toward the latter spacing; splitting the total lift, however, by starting to mine from chutes extending halfway up to the level above. Chutes customarily are spaced at 50, 60 or 70-ft. centers along the gangways. At some mines, additional shafts have been sunk from the surface to the level containing the main pumping station, and these carry the discharge lines from the pumps. As the mines are ventilated by the exhausting system, both the hoisting and so-called water shafts serve as intakes. The main fan is always on the surface, and is connected with the return airways from the various levels by an air hole or a vertical shaft. For economy, when the present deepest levels were developed, main return-air shafts or air holes were not extended to the new level, but connections were made from the new level to that above by two or more holes. It is doubtful that this method will be continued, as complications in the system, increased resistance to flow, and other difficulties undoubtedly will counterbalance any economies this provision may afford.

Jan 1, 1942

By T. R. Graham, R. S. Dean. J. R. Long

Although considerable information has been published concerning manganese additions to the aluminum bronzes, these data refer principally to the two-phase alloys containing 8 to II pet aluminum, with some incidental information on the single-phase alpha solid solution alloys. Straussl gives an excellent review of the literature on aluminum bronzes up to 1927 and a bulletin2 of the Copper Development Association brings the bibliography up to 1938. The most extensive work on manganese addition is that of Rosenhain and Lantsberry,3 who investigated alloys ranging up to 10 pct aluminum and up to 10 pct manganese, and presented data on the physical properties of sand-cast, chill-cast, and several wrought alloys. The greater portion of the work, however, concerns alloys ranging from 7 to 10 pct aluminum in the cast condition and sheds little light on the properties of wrought single-phase alloys. Corson4 notes that alloys containing 10 pct manganese and 4 pct aluminum are not hardenable by heat-treatment, while one with 15 pct manganese and 5 pct aluminum can be hardened, but he gives no tensile data on it. In fact, no systematic study of the properties of single-phase wrought alloys containing substantial amounts of manganese has been reported. It should also be noted that most of the investigators worked with alloys containing significant amounts of iron and silicon, and that these impurities, whether intentionally added or accrued from the raw materials used in the preparation of the alloys, may be expected to have a direct bearing on the resultant properties. In the work on alloys made with electrolytic manganese, the Bureau of Mines has undertaken an investigation of the copper-manganese-aluminum system for the purpose of establishing the constitution and properties of high-purity alloys. In a recent paper6 the authors reported a metallographic investigation of the alpha solid solution area and the adjoining fields of the copper-manganese-aluminum system up to 50 pct manganese. This study established the alpha-phase boundaries at 50" temperature levels from 400' to 850°C. It was found that the addition of manganese to copper-aluminum alloys decreases the solub%ty of aluminum in the alpha phase (Fig I), curving the boundary toward the copper-manganese base line. The greatest change occurs in the first 20 to 25 pct manganese, which decreases the solubility of aluminum to approximately 4 pct. With larger amounts of manganese the alpha boundary tends to parallel the copper-manganese binary. At 13oo'F and higher,

Jan 1, 1947

By Michael B. Bever, John R. Anderson

Carbon may affect the alloys of copper in several ways. Provided an alloying element does not oxidize preferentially, even minute quantities of carbon dissolved in liquid alloys of high copper content will form insoluble carbon oxide gases under oxidizing conditions. Gas porosity in castings of high-copper alloys can originate in this way. In certain alloys of low copper content carbon may have considerable solubility and may be an effective deoxidizer. In these alloys carbon will tend to suppress porosity. Carbon that is dissolved in the molten alloy is likely to be retained in the solidified metal. The effects of carbon on the physical properties of the metal are determined by the form in which it is present. Depending on the alloying elements and also on the cooling rate, carbon may precipitate as graphite, may form a carbide or may remain in solid solution on cooling. As solid copper does not dissolve a measurable amount of carbon, a carbon-bearing solid solution can occur only if the copper is alloyed with a large excess of an element that forms such a solution. The effect of graphite or of carbides on the properties of an alloy will depend on the size and distribution of the precipitated particles. As Hensel pointed out in discussion,' the formation of an alloy carbide may interfere with the age-hardening properties of a copper alloy. One would also expect that the presence of carbides or of graphite will under certain conditions promote corrosion or high-temperature failure in nonferrous alloys. Since carbon has an effect on the soundness of castings and affects the structure and behavior of solid copper alloys, its solubility in the liquid alloys is of practical importance. The isothermal change of carbon solubility with alloy composition is of interest from a theoretical standpoint. The binary alloys of copper with manganese and with nickel are used industrially and serve as a base for more complex alloys. The solubility of carbon in each of these metals is known, but its solubility in their alloys has not been determined. Earlier Data The solubility of carbon in molten pure copper is about o.oooi pct at II00°C and 0.0004 pct at 1475°C.l Various authors2""6 have published data on the solubility of carbon in molten manganese. There is agreement on a value of about 6.7 pct in the temperature range r2170 to 1245°c This solubility value corresponds to the formula Mn3C. It increases very little with increasing temperature. Corson7 states that carbon is soluble in copper-manganese alloys and that the

Jan 1, 1947

By E. O. Karenna, A. D. Smigelskas

This is the third paper in a series on the diffusion of zinc in alpha brass.' At the time of the first paper it was accepted that diffusion in a substitutional type of solid solution depended upon an equal interchange of solute and solvent atoms across the diffusion interface (or past a given lattice reference point). Discrepancies in the size of the areas under the diffusion curves on each side of the interface, if observed, were explained on some other basis than the fact that the solute atoms might cross the diffusion interface without an equal number of solvent atoms diffusing across the interface in the opposite direction. The second paper presented evidence indicating that zinc atoms in alpha brass diffuse across the interface more rapidly in one direction than the copper atoms diffuse across the interface in the opposite direction. This phenomenon forced the interface to move in the opposite direction of the diffusion of zinc atoms to provide space for the additional zinc atoms dissolved in the alpha brass. That the interface and columnar grain structure on one side would remain intact during this mass movement was not expected; how ever, it is gratifying that they did. While the evidence was sufficiently satisfying to the author, it was decided that additional experiments were in order to prove that zinc diffuses more rapidly than copper in alpha brass. It is the purpose of this paper to present the results of these experiments. Procedure A bar of 70-30 wrought brass was selected, to avoid the relatively large volume change in going from beta to alpha brass as in the previous investigation. A bar 7 in. (18-cm.)* long and about 3/4 in. (1.9 cm.) wide was surface ground and polished with abrasive paper on plate glass to 0.4184 0.0002 in. (1.062j + 0.0005 cm.) thick. Six0.00j-in. (0.013-cm.) diameter molybdenum wires, chosen because of their very low solubility in coppcr and alpha brass, were strctched lengthwise along each of the two plane surfaces. Glass tubes placed at right angles to the wires every 1/2 in. held the wires tightly against the brass. The sample was then emersed in an acid copper sulphate plating bath and electroplated to a depth of about 0.020 in. (0.050 cm.) copper on all sides. The glass tubes were no longer necessary to hold the molybdenum wires in place and were removed. The sample was then electroplated to a depth of

Jan 1, 1947

By R. S. Dean. J. R. Long, T. R. Graham

Although considerable information has been published concerning manganese additions to the aluminum bronzes, these data refer principally to the two-phase alloys containing 8 to II pet aluminum, with some incidental information on the single-phase alpha solid solution alloys. Straussl gives an excellent review of the literature on aluminum bronzes up to 1927 and a bulletin2 of the Copper Development Association brings the bibliography up to 1938. The most extensive work on manganese addition is that of Rosenhain and Lantsberry,3 who investigated alloys ranging up to 10 pct aluminum and up to 10 pct manganese, and presented data on the physical properties of sand-cast, chill-cast, and several wrought alloys. The greater portion of the work, however, concerns alloys ranging from 7 to 10 pct aluminum in the cast condition and sheds little light on the properties of wrought single-phase alloys. Corson4 notes that alloys containing 10 pct manganese and 4 pct aluminum are not hardenable by heat-treatment, while one with 15 pct manganese and 5 pct aluminum can be hardened, but he gives no tensile data on it. In fact, no systematic study of the properties of single-phase wrought alloys containing substantial amounts of manganese has been reported. It should also be noted that most of the investigators worked with alloys containing significant amounts of iron and silicon, and that these impurities, whether intentionally added or accrued from the raw materials used in the preparation of the alloys, may be expected to have a direct bearing on the resultant properties. In the work on alloys made with electrolytic manganese, the Bureau of Mines has undertaken an investigation of the copper-manganese-aluminum system for the purpose of establishing the constitution and properties of high-purity alloys. In a recent paper6 the authors reported a metallographic investigation of the alpha solid solution area and the adjoining fields of the copper-manganese-aluminum system up to 50 pct manganese. This study established the alpha-phase boundaries at 50" temperature levels from 400' to 850°C. It was found that the addition of manganese to copper-aluminum alloys decreases the solub%ty of aluminum in the alpha phase (Fig I), curving the boundary toward the copper-manganese base line. The greatest change occurs in the first 20 to 25 pct manganese, which decreases the solubility of aluminum to approximately 4 pct. With larger amounts of manganese the alpha boundary tends to parallel the copper-manganese binary. At 13oo'F and higher,

Jan 1, 1947

By C. L. Burrill

The forecasts presented in this paper constitute an attempt by the writer to predict the pattern of the consumption of petroleum products in the United States during the period of transition from war to peace. Although, in preparing the estimates, secular trends were not overlooked, greater emphasis was placed upon considerations of a cyclical character, or upon influences which might be peculiar to parts of the period. The estimates do not extend beyond the year 1950 because by then conditions in the industry should have returned to normal. The consumption of petroleum products is affected, of course, by changes in the condition of business in general. Before estimates of petroleum consumption could be prepared, therefore, it was necessary to predict the pattern of general business during the period under review, particularly the economic series that in the past have shown the closest relationships with petroleum consumption. It is the writer's view that business activity in this country (as measured by industrial production) will be higher on the average during the period between the end of the war and the year 1950 than it ever was before during a peacetime period of the same duration. When the war is over, consumers will have saved amounts of money that will be very large as compared with any previous accumulations. There is little question, therefore, as to the financial ability of consumers to purchase goods. The production of many durable consumers' goods, such as automobiles, refrigerators and radios, has been completely stopped since early in the war; also, many semidurable and nondurable consumers' goods have not been available in the quantities or the qualities desired. There is considerable needi therefore, for consumers to purchase goods after the war. The important question is whether consumers will purchase goods in "1arge enough quantities to keep our economy running at a high level. The writer answers this question in the affirmative. The mere existence of very large consumer savings lends considerable support to this view because, with such backlogs of " security," consumers can afford to spend more of their current earnings than they otherwise could. Also, several polls have been taken, which indicate that consumers expect to buy large quantities of a variety of goods. Some of the savings, therefore, probably will go into current consumption. Even though this percentage is relatively small, so that the bulk of the funds accumulated by consumers during the war continues to remain as savings during the period under review, spending should be great enough to start the production cycle and keep it

Jan 1, 1945

By John R. Anderson, Michael B. Bever

Carbon may affect the alloys of copper in several ways. Provided an alloying element does not oxidize preferentially, even minute quantities of carbon dissolved in liquid alloys of high copper content will form insoluble carbon oxide gases under oxidizing conditions. Gas porosity in castings of high-copper alloys can originate in this way. In certain alloys of low copper content carbon may have considerable solubility and may be an effective deoxidizer. In these alloys carbon will tend to suppress porosity. Carbon that is dissolved in the molten alloy is likely to be retained in the solidified metal. The effects of carbon on the physical properties of the metal are determined by the form in which it is present. Depending on the alloying elements and also on the cooling rate, carbon may precipitate as graphite, may form a carbide or may remain in solid solution on cooling. As solid copper does not dissolve a measurable amount of carbon, a carbon-bearing solid solution can occur only if the copper is alloyed with a large excess of an element that forms such a solution. The effect of graphite or of carbides on the properties of an alloy will depend on the size and distribution of the precipitated particles. As Hensel pointed out in discussion,' the formation of an alloy carbide may interfere with the age-hardening properties of a copper alloy. One would also expect that the presence of carbides or of graphite will under certain conditions promote corrosion or high-temperature failure in nonferrous alloys. Since carbon has an effect on the soundness of castings and affects the structure and behavior of solid copper alloys, its solubility in the liquid alloys is of practical importance. The isothermal change of carbon solubility with alloy composition is of interest from a theoretical standpoint. The binary alloys of copper with manganese and with nickel are used industrially and serve as a base for more complex alloys. The solubility of carbon in each of these metals is known, but its solubility in their alloys has not been determined. Earlier Data The solubility of carbon in molten pure copper is about o.oooi pct at II00°C and 0.0004 pct at 1475°C.l Various authors2""6 have published data on the solubility of carbon in molten manganese. There is agreement on a value of about 6.7 pct in the temperature range r2170 to 1245°c This solubility value corresponds to the formula Mn3C. It increases very little with increasing temperature. Corson7 states that carbon is soluble in copper-manganese alloys and that the

Jan 1, 1947

By J. R. Long, T. R. Graham, R. S. Dean

ALTHOUGH considerable information has been published concerning manganese additions to the aluminum bronzes, these data refer principally to the two-phase alloys containing 8 to 11 pct aluminum, with some incidental information on the single-phase alpha solid solution alloys. Strauss1 gives an excellent review of the literature on aluminum bronzes up to 1927 and a bulletin2 of the Copper Development Association brings the bibliography up to 1938. The most extensive work on manganese addition is that of Rosenhain and Lantsberry,3 who investigated alloys ranging up to 10 pct aluminum and up to 10 pct manganese, and presented data on the physical properties of sand-cast, chill-cast, and several wrought alloys. The greater portion of the work, however, concerns alloys ranging from 7 to 10 pct aluminum in the cast condition and sheds little light on the properties of wrought single-phase alloys. Corson4 notes that alloys containing 10 pct manganese and 4 pct aluminum are not hardenable by heat-treatment, while one with 15 pct manganese and 5 pct aluminum can be hardened, but he gives no tensile data on it. In fact, no systematic study of the properties of single-phase wrought alloys containing substantial amounts of manganese has been reported. It should also be noted that most of the investigators worked with alloys containing significant amounts of iron and silicon, and that these impurities, whether intentionally added or accrued from the raw materials used in the preparation of the alloys, may be expected to have a direct bearing on the resultant properties. In the work on alloys made with electrolytic manganese, the Bureau of Mines has undertaken an investigation of the copper-manganese-aluminum system for the purpose of establishing the constitution and properties of high-purity alloys. In a recent paper5 the authors reported a metallographic investigation of the alpha solid solution area and the adjoining fields of the copper-manganese-aluminum system up to 50 pct manganese. This study established the alpha-phase boundaries at 50° temperature levels from 400° to 850°C. It was found that the addition of manganese to copper-aluminum alloys decreases the solubility of aluminum in the alpha phase (Fig I), curving the boundary toward the copper-manganese base line. The greatest change occurs in the first 20 to 25 pct manganese, which decreases the solubility of aluminum to approximately 4 pct. With larger amounts of manganese the alpha boundary tends to parallel the copper-manganese binary. At 1300°F and higher,

Jan 1, 1947

By Alfonso Rizo-Patrón, A. M. Gaudin

Previous studies of activation in flotation have directed attention to the action of the activator on the mineral to be floated rather than to the relationship of the activator to the collector. The latter phase of the problem, however, seems to have definite scientific, if not also practical, interest. In the investigation reported in this paper, experiments were carried out, largely with quartz as subject, barium as activator, and oleate as collector. The results obtained indicate that a I: I ratio of collector ion to activator ion gives optimum results, and that a 2:1 ratio almost fails to achieve activation and flotation. Yet, a 2:I ratio would have been expected on stoichiometric grounds, had the coating been a normal salt of the activator ion with the collector ion, since barium is a divalent cation and oleate a monovalent anion. To interpret and rationalize the observations, considerations of the crystal chemistry of quartz are helpful. The point of view to which these considerations lead may be of general applicability to systems involving suspensions of solids in liquids; they confirm that an adsorbed coating is inescapable. Apparatus and Supplies The experimental work consisted in barium-ion abstraction tests, hydrogen-ion and hydroxyl-ion abstraction tests, flotation tests, and determinations of the surface of the crushed quartz. The flotation machine was built according to the design of D. W. McGlashan.* It consists of a drill press in which the bit has been replaced by a stainless-steel impellor surrounding a stainless-steel sta-tor, as in the Fagergren laboratory machine. The air intake is controlled by a valve, and the cell consists of a beaker. The quartz was obtained from vein quartz stored in large chunks. It was first crushed to 20 mesh, then sized on a 28-mesh screen. The 20 to 28-mesh size alone was retained for use. This size was freed of coarse iron by passage through a Ball-Norton magnetic separator, bleached with boiling hydrochloric acid to remove residual abraded iron, washed with distilled water until the washings were thoroughly free of ferrous, ferric, and excess hydrogen ion, and stored in covered Pyrex beakers under water until used. The barium was used as barium chloride, Baker's analyzed C. P. The oleate was used as sodium oleate. It was prepared from sodium hydroxide, Baker's analyzed C. P., and oleic acid purified by R. R. de Arellano3 in the laboratories at the Massachusetts Institute of Technology. The purification procedure was elaborated from the recent $researches of Brown and Shinowara.2 It consisted in: (I) saponification of olive oil with potassium

Jan 1, 1943

By R. M. Waterstrat

The phase VPt has been reported to have a crystal structure of the B19 (AuCd) type at low temperatures.''' A recent investigation3 has indicated that this phase forms by an ordering reaction from the disordered fcc Pt(V) solid solution which is stable at high temperatures. olander4 has shown that there exists a close structural relationship between the orthorhombic B19 structure and a fcc structure possessing the L1 , (CuAu) type of atomic ordering. One may derive the B19 structure by a shear-like displacement of the atoms in the (002) plane of the ordered fcc lattice along the (010) direction through a distance equal to one eighth of the unit cell dimension, see Fig. 1, followed by an orthorhombic distor; tion of the cube axes such that a = 2.693A. h = 4.413A. and c =4.767A (estimated uncertainty 0.005A). Filings of this phase were produced by grinding a VPt alloy having the B19 structure with a diamond dental grinding disc. When these filings were subjected to X-ray diffraction examination, a pattern of a severely cold-worked fcc structure was obtained. higher solution temperature used (1200 C) or to a much lower oxygen pressure than he reported, due to transfer through many bends and tubes in his complicated apparatus. An interesting observation was made when an oxygen addition was attempted in a cylindrical sample of columbium in the cold worked condition rather than in the annealed condition. The interior of the sample re-crystallized during the oxygen addition at 900°C. The periphery, however. (1 mm) did not recrystallize. A similar sample without oxygen recrystallized throughout the entire cross section. It appears that the re-crystallization is hindered by interstitial oxygen. Presumably, the interior recrystallized before appreciable oxygen could diffuse into the core. This work was supported by the United States Atomic Energy Commission. When the filings were annealed in a high vacuum furnace for 15 min at 110O0C, however. they returned to the B19 structure perhaps as a result of reordering. Subsequent less-severe cold-working of these filings by grinding in a hardened steel mortar and pestle at room temperature produced a transformation into a cold-worked L1, structure which was slightly tetragonal. Thus it appears that the degree of deformation may influence the final structure. Considerable line-broadening was observed in X-ray diffraction patterns obtained from the cold-worked filings and therefore no attempt was made to obtain accurate lattice parameters. Vacuum annealing treatments at 1100'C intended

Jan 1, 1970

By Carl F. Floe, Michael B. Bever

THE possibility that carbon may be soluble in copper to a limited extent has been recognized for over a century. The quantitative investigation of this problem, however, requires more sensitive techniques than have formerly been available. Three recent developments have made possible more accurate determinations: the vacuum-fusion method of analysis, the production of copper of high purity and the availability of high-purity refractories, particularly graphite. In addition to its obvious theoretical interest, the problem of carbon solubility in copper is of practical importance. In the production of copper and of high-copper alloys, carbonaceous covers are frequently used. If even minute amounts of carbon are dissolved, insoluble carbon oxide gases will be formed when such metals are poured under oxidizing conditions. A mechanism of this kind could well be one of the principal causes of gas porosity in casting copper-base products. REVIEW OF LITERATURE In 1823 Vivian1 raised the question as to whether copper by overpoling becomes "combined with a minute portion of carbon." Karsten2 asserted, in 1832, that carbon reduces the high-temperature strength of pure copper, so that when the carbon content has reached 0.2 per cent the metal will be brittle at a dark red heat. According to Karsten, carbon contents of o.05 per cent make it difficult to hot-work copper. He also reported that the specific gravity of copper is 8.8969 and that it increases to 8.92 58 if the copper is cemented with carbon and then melted. He emphasized the difficulty of determining analytically the small amounts of carbon present in copper. The metal was removed by wet methods and the residue considered as carbon. At Percy's request, Dick,3 in 1856, carried out various working tests on copper that had been in prolonged contact with carbon, and found that the working properties of the metal had not been affected. He also attempted to determine the presence of carbon analytically. In one experiment the copper was dissolved and the residue was fused with litharge, and in another essentially a combustion analysis was made on a copper sample. In a final experiment, a sample was dissolved and the residue subsequently subjected to a combustion analysis. Indications of as much as o.005 per cent carbon were found, but Dick considered his work inconclusive largely because of the possible interference of sulphur. Percy4 concluded, from Dick's experiments and from some experimental work of his own, that the solubility of carbon in copper had not been established with

Jan 1, 1945

By A. A. Collins

OF widespread interest to all lead metal¬lurgists is a dross smelting process that will consistently give mattes and speiss of low lead and high copper contents. It is -a problem that has intrigued operators through the years. In the past few years, with increased amounts of copper and overcrowded metallurgical furnaces, it has been almost imperative to evolve some method. Experience at El Paso has shown that high copper-to-lead ratios can be consistently attained by use of the new soda process.* OLDER METHODS Three older methods; i.e., I. Dross plus siliceous ore and limestone, 2. Dross plus one fourth blast-furnace speiss and siliceous ore, 3. Dross plus sulphides and siliceous ore and scrap iron, do not give consistent results and the products are higher in lead and lower in copper than those produced with the soda process. Any radical changes in the blast-furnace drosses will throw any of these older methods into a tailspin. For almost ten years, El Paso used the third method, with varying results. It was noted that as the arsenic and antimony contents of the dross increased, the speiss and matte steadily increased in lead and decreased in copper. A dross containing four parts of copper to one part of arsenic was considered to be ideal. At times this balance of copper to arsenic was almost impossible to obtain, especially when handling copper Cottrell dusts, which vary so greatly in copper and arsenic. Custom smelters like El Paso, handling a great variety of dusts, concentrates and ores, are apt to have anywhere from 1 to 15 pct copper on charge, with a variable in arsenic of from 0.5 to 2 pct. With such conditions, and drosses varying from 12 to 40 pct copper, an operator using the older dross reverberatory practices would find it just about im¬possible to control the reverberatory operations and to produce a good product low in lead and high in copper. These conditions prevailed at El Paso from the year 1940 to the present. In May 1942 it, was decided to experiment with the soda process. THE SODA PROCESS After considerable work the soda method was finally evolved to the present state. It has never failed to produce a good product even under the most adverse conditions. It might be well to remember that many men of thought in the smelting industry have at one time or other suggested the removal of all copper, arsenic and antimony from the lead blast-furnace charge as an aid to better metallurgy.

Jan 1, 1947

By Irving M. Symonds

Compania Minera de Penoles, S. A., at its Avalos unit operates a lead-zinc concentrator having a capacity of about 600 short tons per day. Lead and zinc concentrates are made by flotation methods. The concentrator is at Terminal de Provi-dencia, in the state of Zacatecas, some 70 miles south of Saltillo, Coahuila. The Penoles-Avalos railroad operating between the plant and Estacion Avalos, a distance of 6 miles, makes connections with the Coahuila and Zacatecas railroad, which in turn connects with the Nacionales de Mexico at Saltillo. The three railroads are each of different gauge, requiring the transfer of all supplies and concentrates at each junction. The mill operates on company ores, on ores from leased mines, and as a custom mill. The custom business is very small. The lead concentrates are shipped to company smelters at Monterrey, Nuevo Leon and Torreon, Coahuila. Since the European war, all zinc concentrates have been shipped to the United States. Ore Treated The major source of ore supply is a group of four mines owned or leased by the company, some three miles south of the mill in the mountains, from which the ore is delivered to the mill by a gravity aerial tramway. Custom ore comes in by rail. The ores occur in chimneys. The upper levels contained oxidized siliceous ores of lead, copper, silver and gold, with varying amounts of zinc. These ores were direct-smelted. In the first two years of operation a good deal of the tailing loss was caused by the oxidized content of the ores milled. Much of the ore in the transition zones between the oxides and sulphides was not mined. The ores now being milled are clean, hard sulphides in a limestone gangue, with only occasional contamination of oxides. The lead and zinc sulphides are of coarse structure and are freed even above flotation sizes. The galena is usually "steel" colored, easily and quickly floated. When there is any oxidation, it is usually on the coarsest crystals. The zinc minerals vary a good deal in color; a resin sphalerite predominates but there are varying shades of brown marmatites. On an average, the zinc sulphides contain 64 per cent zinc. The only common copper mineral is chalcopy-rite. Little is known of the occurrence of gold and silver. Waste minerals are mainly limestone and pyrite, both of which are barren. The ores vary from 20 to 35 per cent pyrite. Mill heads for the year 1940 and the first eight months of 1941 are given in Table I.

Jan 1, 1943

By Irving M. Symonds

COMPAÑIA Minera de Peñoles, S. A., at its Avalos unit operates a lead-zinc concentrator having a capacity of about 600 short tons per day. Lead and zinc concentrates are made by flotation methods. The concentrator is at Terminal de Providencia, in the state of Zacatecas, some 70 miles south of Saltillo, Coahuila. The Peñoles-Avalos railroad operating between the plant and Estacion Avalos, a distance of 6 miles, makes connections with the Coahuila and Zacatecas railroad, which in turn connects with the Nacionales de Mexico at Saltillo. The three railroads are each of different gauge, requiring the transfer of all supplies and concentrates at each junction. The mill operates on company ores, on ores from leased mines, and as a custom mill. The custom business is very small. The lead concentrates are shipped to company smelters at Monterrey, Nuevo Leon and Torreón, Coahuila. Since the European war, all zinc concentrates have been shipped to the United States. ORE TREATED The major source of ore supply is a group of four mines owned or leased by the company, some three miles south of the mill in the mountains, from which the ore is delivered to the mill by a gravity aerial tramway. Custom ore comes in by rail. The ores occur in chimneys. The upper levels contained oxidized siliceous ores of lead, copper, silver and gold, with varying amounts of zinc. These ores were direct-smelted. In the first two years of operation a good deal of the tailing loss was caused by the oxidized content of the ores milled. Much of the ore in the transition zones between the oxides and sulphides was not mined. The ores now being milled are clean, hard sulphides in a limestone gangue, with only occasional contamination of oxides. The lead and zinc sulphides are of coarse structure and are freed even above flotation sizes. The galena is usually "steel" colored, easily and quickly floated. When there is any oxidation, it is usually on the coarsest crystals. The zinc minerals vary a good deal in color; a resin sphalerite predominates but there are varying shades of brown marmatites. On an average, the zinc sulphides contain 64 per cent zinc. The only common copper mineral is chalcopyrite. Little is known of the occurrence of gold and silver. Waste minerals are mainly limestone and pyrite, both of which are barren. The ores vary from 20 to 35 per cent pyrite. Mill heads for the year 1940 and the first eight months of 1941 are given in Table I. [ ]

Jan 1, 1942

By L. D. Fetterolf, G. T. Mahler, W. M. Peirce, R. K. Waring

UNTIL recently, the only commercial method of producing magnesium has been fused salt electrolysis, despite a considerable amount of experimental work on the direct reduction of magnesium oxide. In this early work, a number of investigators demonstrated that magnesium oxide would react with any one of several reducing agents to produce magnesium vapor, but that the mixture of magnesium oxide and reducing agent must be heated to a high temperature even in a vacuum. In particular, it was demonstrated that silicon and aluminum are effective reducing agents and that when either of these is used the magnesium vapor can be condensed to massive metal. In spite of this knowledge, no successful commercial reduction process was developed, at least in this country, because of the operational difficulties imposed by the requirement of high temperature and vacuum and because of the high cost of the reducing agent. The outstanding experimental work done by Pidgeon, who carefully reviewed all of the known methods of making magnesium and then selected ferrosilicon reduction, overcame some of the operational difficulties. The process developed by Pidgeon comprises briquetting a mixture of calcined dolomite and reducing agent, pre-heating the briquets to about 600°C. in an externally heated alloy retort, reducing the MgO with silicon in an evacuated horizontal alloy retort heated externally to about 1150°C., and condensing the magnesium vapor to a solid in a cold extension of the retort projecting beyond the fr6nt of the furnace. A major advantage of Pidgeon's process is that the retort is not cooled down between charges. Earlier investigators had used apparatus that necessitated cooling and reheating of the retort between charges. Early in January 1942, when the War Production Board was considering the Pidgeon process for quickly increasing the production of magnesium, The New Jersey Zinc Co. offered to have a research investigation of the process carried on, with the hope of assisting in its further development. This offer was accepted, and a two-retort pilot plant was built at Palmerton and put in operation on Jan. 29, 1942. An intensive investigation of certain phases of the process was carried out in the ensuing four months. This investigation was completed in the last part of May 1942, and the pilot plant was then shut down. Subsequently, The New Jersey Zinc Co. was requested to have further development work done on the process, and a more extensive investigation was undertaken in August I942 under contract with the War production Board and under the super- vision of the War Metallurgy Committee. This paper describes the phases of the investigation that are thought to .be

Jan 1, 1944

By Gordon G. Bentle, W. P. Fishel

GREINER, Marsh, and Stoughton1 have reviewed the literature in a monograph on the iron-silicon system. The lack of agreement among the various studies may be due to the difference in the purity of materials in some cases. The results of the X-ray method indicate only a general rather than a specific limit of the y loop. The iron-titanium system was investigated by Roe and Fishel,' whose results are used in determining the iron-silicon-titanium y loop. The literature indicates that no study has been made thus far of the iron-silicon-titanium system in the y loop region. Experimental Procedure The alloys were made from Armco iron, 99.86 pct Si, and 98.5 pct Ti. The titanium contains 1.07 pct Fe. The Armco iron contains 0.01 pct C, 0.005 pct Si, 0.02 pct Mn, 0.006 pct P, 0.01 pct S, and 0.04 pct Cu. A dilatation sample of Armco iron was prepared in the same manner as were the other samples. Several dilatation runs indicated that Ac3 begins at 905°C and ends at 910°C, which compares favorably with the study of Wells, Ackley, and Mehl' employing specially purified iron. All alloys were melted in an induction furnace in Alundum crucibles and were top poured into baked core sand molds. The ingots weighed about 600 g as cast. Dilatation samples of 4 in. by % in. diam were taken from the bottom end of the ingot, from which turnings for analysis were taken. Turnings from each end of two of the samples indicated that the alloys possessed uniform silicon content. A hole was drilled halfway through each end of a 4 in, dilatation sample. A chromel-alumel thermocouple was inserted in each hole and the surrounding metal peened in to hold the thermocouple in place. Fig. 1 represents the dilatation apparatus. The heating unit is an Alundum tube wound with resistance wire; the dilatation tube is a McDanel combustion tube; the push rod is zircon; the dial gage is graduated in 0.0001 in. and was vibrated to prevent sticking. A blank run over the temperature range of interest gave no significant dilatation. The thermocouples were attached to a multiple recording micromax which indicated the temperature at each end of the sample at 35 sec intervals. A Lindberg control unit governed the rate of heating of the furnace, and lowering or raising the

Jan 1, 1957

By Jan Law

Problems of oil recovery are attacked from the approaches dictated by the two strikingly dissimilar complexes that comprise an oil reservoir—the fluid complex and the interstitial complex. Knowledge of the fluid complex, due to labors in the fields of fluid mechanics and physical chemistry, has far outdistanced knowledge of the interstitial characteristics of the sand complex. This paper is concerned with the latter and applies the technique of statistics to petrographic facts—namely, porosity and permeability—dealing with what might be called petrometry. Statisticians have long worked within the problem of reconstruction of a universe oi variables by means of samples that comprise a small percentage of the universe from which the samples were drawn. Core-analysis data comply with the requisite of random sampling as stipulated by theoretical statistics. A basic concept of statistics employs t.he following substitution: 1. The results of sampling are arranged as a frequency distribution. 2. The observed frequency distribution is compared with a mathematically precise distribution. 3. If a sufficiently good agreement is found between the two, the precise distribution is substituted in all subsequent operations involving characteristics of the sampled material. This mathematically precise distribution is also known as the normal curve, curve of error, the probability, the Gaussian, and the bell-shaped curve and is describable with but two figures. Further, these two figures, the arithmetic average and the standard deviation, are subject to mathematical manipulation. This paper demonstrates that, in some cases in the Dominguez field of Southern California, if sufficient core-analysis samples are taken over not too great a thickness of sediments, the resultant permeability and porosity assemblages give satisfactory agreement with ilormal curves. It is shown that the indications are strong that oil wells wherein a satisfactory agreement is found are predictable as to productivity. Since the predictions are made by employing the laws of chance that are operative within sedimentation, it follows that the mechanism by which the predictions were made is a basic concept of reservoir mechanics. Therefore, tentative examples are given of the application of normal curves to the solution of problems of primary and secondary recovery. Nature of Permeability Frequency Distributions Core-analysis data are made available as a tabulated depth vs. permeability profile. The nature of the distribution of permeability values within a given strati-graphic interval may be approximated from an array constructed with samples plotted in the order of their appearance with depth (accession number) against their permeability value in millidarcys. A wide variation in the nature of the distribution of K (permeability) values for

Jan 1, 1944

By Dan Crackel, G. G. Ramos, Mark Heisel

INTRODUCTION Feasibility studies indicated that a cratering type stoping method was best suited to the character of the first ore block at Carr Fork. This method known as vertical crater retreat (VCR) has since been modified to a combination cratering and deck blasting using VCR drop raises for initial undercut development . The modified form retains many of the advantages of VCR while allowing high tonnage production blasts which have offset many of the disadvantages. FIRST CONCEPTS AND PREMISES Geologic Considerations The Steep Highland Boy (SHB) skarn orebody, the first of several blocks being developed, is a steeply dipping 70° to 90° limb of a syncline, with a width averaging 25 m (82 ft). The bed has a consistent east-west strike length of over 400 m (1300 ft) and extends from the surface to depths of over 1000 m (3300 ft). The footwall is highly fractured quartzite and the hanging wall grades from garneti te to limes tone and hornfe 1s. Because of the limestone in the hanging wall, the hanging wall appears more competent than the footwall. The ore is garnetite with lenses of massive sulphide and magnetite. The quartzite footwall is highly fractured not only because of the bedding but also due to the folding and intrusion of the quartz monzonite. This irregular footwall outline of some stopes in- creases the likelihood of excessive dilution. The principal ore mineral is chalcopyrite with some bornite. The garnetite ore is quite variable in terms of compressive strength and drillability. In addition to the sulphide and magnetite lenses, it is transected by clay- altered dikes and major and minor north-east faults. TABLE (1) gives the range and mean strengths of the rocks. Investigating Mining Methods Initial consideration of a suitable mining method centered around maximum safety and efficiency with minimum potential dilution. The following major methods were considered and investigated. Cut and fill mining was eliminated because of low productivity, the cost and problems associated with providing fill, and the relatively unsafe nature of the method. Sublevel caving was rejected due to the unpredictable cavability of the waste and the geometry of the ore body. Conventional sublevel or blasthole methods require excessive development, as fan and ring drills are limited to efficient drilling in the 18 to 25 m range (60 to 80 ft). Mining downdip with equipment drilling small diameter holes would have required eight separate extraction/drill horizons with crosscuts and associated excavation in the main ore block. The use of down the hole (DTH) machines cap- able of drilling 165 m (6g in) diameter holes

Jan 1, 1981

By Irving M. Symonds

COMPA[N]IA Minera de Penoles, S. A., at its Avalos unit operates a lead-zinc concentrator having a capacity of about 600 short tons per day. Lead and zinc concentrates are made by flotation methods. The concentrator is at Terminal de Providencia, in the state of Zacatecas, some 70 miles south of Saltillo, Coahuila. The Pe[n]oles-Avalos railroad operating between the plant and Estacion Avalos, a distance of 6 miles, makes connections with the Coahuila and Zacatecas railroad, which in turn connects with the Nacionales de Mexico at Saltillo. The three railroads are each of different gauge, requiring the transfer of all supplies and concentrates at each junction. The mill operates on company ores, on ores from leased mines, and as a custom mill. The custom business is very small. The lead concentrates are shipped to company smelters at Monterrey, Nuevo Leon and Torréon, Coahuila. Since the European war, all zinc concentrates have been shipped to the United States. ORE TREATED The major source of ore supply is a group of four mines owned or leased by the company, some three miles south of the mill in the mountains, from which the ore is delivered to the mill by a gravity aerial tramway. Custom ore comes in by rail. The ores occur in chimneys. The upper levels contained oxidized siliceous ores of lead, copper, silver and gold, with varying amounts of zinc. These ores were direct-smelted. In the first two years of operation a good deal of the tailing loss was caused by the oxidized content of the ores milled. Much of the ore in the transition zones between the oxides and sulphides was not mined. The ores now being milled are clean, hard sulphides in a limestone gangue, with only occasional contamination of oxides. The lead and zinc sulphides are of coarse structure and are freed even above flotation sizes. The galena is usually "steel" colored, easily and quickly floated. When there is any oxidation, it is usually on the coarsest crystals. The zinc minerals vary a good deal in color; a resin sphalerite predominates but there are varying shades of brown marmatites. On an average, the zinc sulphides contain 64 per cent zinc. The only common copper mineral is chalcopyrite. Little is known of the occurrence of gold and silver. Waste minerals are mainly limestone and pyrite, both of which are barren. The ores vary from 20 to 35 per cent pyrite. Mill heads for the year 1940 and the first eight months of 1941 are given in Table I. [ ]

Jan 1, 1942

By H. L. Riley, B. W. Gandrud

A froth flotation unit was added to the DeBardeleben Coal Corporation's Empire washer at Empire, Alabama, in the fall Of I94O following an investigation of possible ways and means of recovering coal values from settling-tank overflow or slurry. Officials of the DeBardeleben corporation hoped that some practical and reasonably economical way could be found for recovering fine coal from overflow water, although there had as yet been very little progress along this line in the Alabama coal fields. The Bureau of Mines was asked to cooperate in the project through its Southern Experiment Station, at University, Alabama. This paper presents a brief description of the process and the installation that resulted from the investigation of the overflow water or slurry problem at the Empire mine. The experimental data include' as a Part of this Paper were obtained during the course of the investigation in 1940 Since that time, however, the flotation unit has been running more or less continuously without significant operational changes and is still Performing pretty much in accordance with the data obtained in 1940. Flowsheet at Empire and Type of Coal Treated The Empire mine is developed on the Black Creek bed near the the border of the Warrior field. The coal in this bed is extremely low-ash and although there is an almost complete absence of bone coal and partings, the bed is so thin that, with mechanized mining, a high percentage of rock from roof and floor inevitably gets into the run-of-mine coal. The thickness of the Black Creek bed throughout the part of the Warrior field in which it is mined extensively is rarely over 30 in. and probably would average about 25 in, the coal is of the high-volatile A rank and of excellent quality, but as a result of admixture of roof and floor material, the run-of-mine product usually contains I ; to 20 pct rock by weight. he following is a proximate analysis on an "as-received " basis of a typical seam sample from the Empire mine:' moisture, 3.0 pet; volatile, 34.6 fixed carbon 58.3; ash, 4.1 This sample shelved 15,070 Btu per pound and 0.9 pct sulphur on a moisture-and-ash-free basis. In the Empire preparation plant the lump sizes above 3 in. are removed and hand-picked on a Marcus conveying Screen, the 3 to ? -in. size is removed by vibrating screens and washed in two Montgomery single-cell jigs, and the ?-in. to o slack is cleaned on four diagonal

Jan 1, 1949