Search Documents

By L. D. Fetterolf, G. T. Mahler, W. M. Peirce, R. K. Waring

Until recently, the only commercial method of producing magnesium has been fused salt electrolysis, despite a considerable amount of experimental work on the direct reduction of magnesium oxide. In this early work, a number of investigators demonstrated that magnesium oxide would react with any one of several reducing agents to produce magnesium vapor, but that the mixture of magnesium oxide and reducing agent must be heated to a high temperature even in a vacuum. In particular, it was demonstrated that silicon and aluminum are effective reducing agents and that when either of these is used the magnesium vapor can be condensed to massive metal. In spite of this knowledge, no successful commercial reduction process was developed, at least in this country, because of the operational difficulties imposed by the requirement of high temperature and vacuum and because of the high cost of the reducing agent. The outstanding experimental work done by Pidgeon, who carefully reviewed all of the known methods of making magnesium and then selected ferrosilicon reduction, overcame some of the operational difficulties. The process developed by Pidgeon comprises briquetting a mixture of calcined dolomite and reducing agent, preheating the briquets to about 600°C. in an externally heated alloy retort, reducing the MgO with silicon in an evacuated horizontal alloy retort heated externally to about II50 C., and condensing the magnesium vapor to a solid in a cold extension of the retort projecting beyond the front of the furnace. A major advantage of Pidgeon's process is that the retort is not cooled down between charges. Earlier investigators had used apparatus that necessitated cooling and reheating of the retort between charges. Early in January 1942, when the War Production Board was considering the Pidgeon process for quickly increasing the production of magnesium, The New Jersey Zinc Co. offered to have a research investigation of the process carried on, with the hope of assisting in its further development. This offer was accepted, and a two-retort pilot plant was built at Palmerton and put in operation on Jan. 29,1942. An intensive investigation of certain phases of the process was carried out in the ensuing four months. This investigation was completed in the last part of May 1942) and the pilot plant was then shut down. Subsequently, The New Jersey Zinc Co. was requested to have further development work done on the process, and a more extensive investigation was undertaken in August 1942 under contract with the War Production Board and under the supervision of the War Metallurgy Committee. This paper describes the ,phases of the investigation that are thought to be of sufficient general interest to merit publication.

Jan 1, 1944

By A. William Johnson

It was pointed out in an earlier paper1 that our understanding of the atomic mechanism by which diffusion occurs in metallic alloys is scarcely in an advanced state. This unsatisfactory condition is the result not of any lack of interest, but of the difficulty of designing experiments that .will yield suitable data. The diffusion coefficient of an alloy, measured in the usual way, is simply a number specifying the rate of homogenization of a nonhomo-geneous metal; this number, of itself, can furnish neither the rate at which the individual atoms move nor information as to the mechanism by which they move. It does not necessarily follow, however, that such information cannot be obtained, even if the path to be followed is still not clear. Much success has been attained in the study of diffusion in ionic crystals. A number of experiments, for which there are few counterparts in connection with metals, yield information often indicating a detailed mechanism by which diffusion probably occurs. From such work, quite acceptable theories of lattice imperfections have been developed by Wagner, Schottky, Frenkel, Jost and others.2 It is postulated that real crystals of stoichiometric composition contain, in equilibrium, certain imperfections of which the most importarlt types are: (I) vacant cation sites, with an equal number of interstitial ions; (2) vacant anion sites, with an equal number of interstitial ions; (3) equal numbers of anions and cations in interstitial positions; (4) equal numbers of vacant anion and cation sites. The classification of a particular crystal according to this scheme then follows from studies of the variation of electrical conductivity with pressure of the electronegative component surrounding the crystal, with ion size, and with temperature; other physical phenomena, such as the Hall effect, have aided in establishing the classification. The relative mobility of the anion and cation may be determined by chemical analysis of the salt at the electrodes following electrolysis. With such information, and knowing that one ion never occupies the lattice site normally belonging to an ion of opposite sign, it is usually possible to ascertain the diffusion mechanism. It is clear that the same experiments are not applicable to metal crystals, and substitute experiments that yield as much information have not yet been devised. Much can be learned, however, about the mobilities of the two* kinds of atoms in alloys by the use of radioactive metals as indicators. Only one such experiment has been performed in the past. In 1933, Seith and Keil,3 in an effort to explain the great difference between the rate of diffusion of gold in lead and of lead in lead, measured the rate of diffusion of radioactive lead in 3 gold-lead

Jan 1, 1942

By E. A. Gulbransen, J. W. Hickman

THE physical and chemical structure of the oxide films formed on metals and alloys is of interest in our understanding of their protective properties. According to Pilling and Bedworth,1 if the specific volume of the oxide is equal to or greater than that of the metal, a compact or continuous structure results; if the volume of the oxide is less, a cellular or porous structure forms. With the cellular type of coating the surface layer of oxide offers no impedance to oxidation; at a given temperature the rate of oxidation is quite constant. On the other hand, the compact type of coating acts as an effective barrier to oxygen and the rate of oxidation will follow a parabolic law. The recent work of Gulbransen2 and of Leontis and Rhines3 on the oxidation of magnesium indicates that it is not necessary for the volume of the oxide to be greater than that of the metal in order that the oxidation may follow a parabolic rate law. One exception to the rule of Pilling and Bedworth' is noted by Scheil;4 namely, tungsten. At 500° and 700°C long-time oxidations indicate a linear rate law with time. However, Dunn's5 oxidation measurements from 700° to 1000°C indicate that a parabolic rate law is followed. The oxide is mainly yellow W03 with a thin layer of the blue oxide. Preliminary results on the oxidation of tungsten6 in the temperature range 400° to 500°C indicate that the oxidation does proceed according to a parabolic rate law. Irrespective of the actual rate law that tungsten may obey, it is of interest to compare the results obtained on the oxidation of tungsten in the thin film region with those found when the metal is scaling. A time-temperature study of the oxides formed on both molybdenum and tungsten may indicate whether there exist any peculiarities in the oxide structures of the thin film region compared with those of the scaling region of oxidation. In a recent paper the authors' presented an investigation of the structures of the oxide films formed on the metals iron, cobalt, nickel, chromium and copper. The results of these studies are presented in graphical form as existence diagrams of the oxides on a time-temperature scale. The existence diagrams of the oxides occurring on some of the metals are simple and show few chemical transitions, but there are many cases in which the physical state of the oxide surface changes as a function of time and temperature, as evidenced by the appearance or disappearance of orientation effects and sharpness of patterns. In general an increase in temperature results in an increase in

Jan 1, 1947

By L. W. Kempf, K. R. Van Horn

Plastic deformation of most commercia1 metals within a sufficiently low temperature range results in profound changes in structure and properties, of which the causes and effects are not completely understood. One of these effects is the presence of internal residual stresses and strains, which ordinarily do not appear to require specific consideration in most structural applications but which may be quite undesirable in particular instances. For example, in heavy sections that require considerable machining before assembly, residual stresses may be undesirable because of the distortion they cause when their balance is disturbed by machining or otherwise. In addition, the distribution of stresses may be such that it acts in the same direction as the applied load, thus bringing about premature failure or reducing the load-carrying capacity of the member. One source of residual stress in metal structures is the plastic deformation that may occur during rapid cooling from relatively elevated temperatures, as in the cooling of a casting in the mold or the quenching of a heavy section from elevated temperatures during heat-treatment. These residual stresses are usually undesirable because their direction of operation and magnitude cannot be controlled well enough to permit utilization of the changes in properties of the metal that they may bring about. The most convenient manner of controlling such residual stress is by proper selection of the cooling rate or by reheating to a temperature at which plastic flow can take place, resulting in relief of the residual stresses and strains. Both of these methods of control, however, may cause a reduction in the optimum properties obtainable from the previous operation. A compromise must be struck, and if it is to result in the best possible combinations of properties, specific information must be available regarding the magnitude of the stresses and the rate at which they are affected by variations in cooling rate or in reheating temperature. The complete quantitative estimation of residual stress in complicated metal shapes is exceedingly difficult, if not impossible. In simple sections, however, relatively quantitative analysis may be applied and useful cstimations of stress distribution may be made. This paper is concerned largely with the rate of relief, upon reheating, of internal residual stress in simple aluminum-alloy structures. Since even with simple structures quantitative estimation of residual stresses is laborious and costly, an attempt was made to find other means of collecting data upon which commercial heat-treatments might be based. Incidentally, a few data were collected bearing on the problem of relaxation of aluminum alloys. Determination of Residual Stresses The magnitude and distribution of residual stresses in simple aluminum-alloy shapes rapidly cooled from elevated temperatures has been discussed in a previous paper.' Fig. I reproduces some of the data

Jan 1, 1942

By E. A. Gulbransen, J. W. Hickman

The physical and chemical structure of the oxide films formed on metals and alloys is of interest in our understanding of their protective properties. According to Pilling and Bedworth,¹ if the specific volume of the oxide is equal to or greater than that of the metal, a compact or continuous structure results; if the volume of the oxide is less, a cellular or porous structure forms. With the cellular type of coating the surface layer of oxide offers no impedance to oxidation; at a given temperature the rate of oxidation is quite constant. On the other hand, the compact type of coating acts as an effective barrier to oxygen and the rate of oxidation will follow a parabolic law. The recent work of Gulbransen2 and of Leontis and Rhines3 on the oxidation of magnesium indicates that it is not necessary for the volume of the oxide to be greater than that of the metal in order that the oxidation may follow a parabolic rate law. One exception to the rule of Pilling and Bedworth¹ is noted by Scheil;4 namely, tungsten. At 500° and 700°C long-time oxidations indicate a linear rate law with time. However, Dunn's6 0xidation measurements from 700°to 1000°C indicate that a parabolic rate law is followed. The oxide is mainly yellow WO a with a thin layer of the blue oxide. Preliminary results on the oxidation of tungsten6 in the temperature range 400° to 500°C indicate that the oxidation does proceed according to a parabolic rate law. Irrespective of the actual rate law that tungsten may obey, it is of interest to compare the results obtained on the oxidation of tungsten in the thin film region with those found when the metal is scaling. A time-temperature study of the oxides formed on both molybdenum and tungsten may indicate whether there exist any peculiarities in the oxide structures of the thin film region compared with those of the scaling region of oxidation. In a recent paper the authors7 presented an investigation of the structures of the oxide films formed on the metals iron, cobalt, nickel, chromium and copper. The results of these studies are presented in graphical form as existence diagrams of the oxides on a time-temperature scale. The existence diagrams of the oxides occurring on some of the metals are simple and show few chemical transitions, but there are many cases in which the physical state of the oxide surface changes as a function of time and temperature, as evidenced by the appearance or disappearance of orientation effects and sharpness of patterns. In general an increase in temperature results in an increase in

Jan 1, 1947

By Frederick N. Rhines

Because of the nature of the environments in which metals are handled, it is natural that gases should be suspected of intruding into metallurgical operations, there to produce effects both beneficial and detrimental. The problem of tracing and controlling such effects is often made difficult by the complexity of the conditions surrounding their occurrellce, even though the fundamental mechanisms invalved may be simple and of familiar type. Many gas-metal reactions are known to be implemented by Processes of diffusion. These form a homogeneous group of phenomena which become more readily understandable when viewed together, in that the knowledge gained from one serves to interpiet the next. It is the purpose of the present Paper to present, by means of examples drawn from practice, a brief survey of the ways in which gas-metal diffusion serves and obstructs the Purposes of the metal-fabricating industries. The selection of the cases described was made by consulting more than thirty-six practicing experts whose combined experience provided an extensive coverage of the field and who were in a position to supply examples of occurrences of present day interest. The response was generous and it is regrettable that space permits the description of only a limited number of typical examples with ' but brief mention of parallel cases. The Nature of Gas-metal Diffusion The term ugas-metal diffusion," although commonly used, is ambiguous in so far as it implies that a definite group of " substances may be identified as gases and may be expected to behave in a manner distinct from other substances in association with metals. "Gases" such as oxygen and hydrogen when diffusing through a liquid or solid metal are properly components of the liquid or solid solution; they behave as alloying elements and are not to be distinguished in their diffusion characteristics from other elements, except that each has an individual rate of diffusion. On the other hand, a number of metals in certain.temperature ranges are volatile to the extent that they may appear in the form of vapor in metallurgical operations. For the sake of greater definiteness, therefore, it will be convenient to regard as "gas-metal diffusion" any process in which the result depends upon one or more of the diffusing elements appearing, at some stage, in the gaseous state, or as a compound gas. NO element, gaseous or otherwise, can diffuse through a liquid or solid metal unless it is at least slightly soluble in that metal. The elements of low atomic number

Jan 1, 1944

By Arthur T. Allen

THE Kingsport formation, a part of the Knox dolomite of Ordovician age, is composed of 538 ft of dolomitc and limestone. Numerous bands, layers and nodules of chert, arenaceous and shale zones are present. The characteristics displayed by these features have been useful in mapping, prospecting and mining. Perhaps a better understanding of the origin of these zones will increase their usefulness. Introduction The presence of numerous bands, nodules, and irregular bodies of chert within the Kingsport formation in the Mascot locality has long been recognized. Oder and Miller1 mention the general characteristics, but do not deal with the chert occurrences in detail. When the occurrence of chert is studied in fresh exposures underground, a variety of characteristics is noted which has been useful in correlation and in detailing the sub-surface stratigraphy. Although the writer has no desire to enter into a controversy over the origin of chert, many observations have been made of its local characterigtics. A detailed stratigraphic section is included which shows the position of the individual horizons discussed in the following paragraphs. The term "chertification" has been adopted from Fowler and Lyden2 for use here. It refers to the replacement of lime- stone by introduced silicic acid. The writer uses it to refer to the occurrencc of introduced or original chert in limestone and dolomite. In this writing "syngenetic chert" refers to chert which has been deposited contemporaneously with the enclosing limestone or dolomite. Also, it is considered to include interstitial silica shown by chemical analysis and insoluble residues. The term "epigenetic" is applied to all chert which has been introduced after consolidation of the rocks in which it occurs, regardless of the nature of the depositing solutions. Syngenetic Chert It is the belief of the author that a large percentage of the chert found in the Kingsport formation is syngenetic. The widespread occurrence of similar nodules and bands of chert in the same horizon far from one another and far from areas of deformation or alteration of the enclosing rocks is difficult to explain by infiltration of the silica after compaction of the enclosing rocks. When chert of this type does occur near zones of movement it is likely to be involved in faulting and brecciation which indicates that it was deposited prior to deformation. Older Epigenetic Chert There are several occurrences of nodules in the Kingsport which seem to be epigenetic as pointed out in the following examples: A cherty zone occurs 26 ft above the o bed (Fig =). This is not always present but is found in the greater part of mine work-

Jan 1, 1949

By Frederick N. Rhines

Because of the nature of the environments in which metals are handled, it is natural that gases should be suspected of intruding into metallurgical operations, there to produce effects both beneficial and detrimental. The problem of tracing and controlling such effects is often made difficult by the complexity of the conditions surrounding their occurrellce, even though the fundamental mechanisms invalved may be simple and of familiar type. Many gas-metal reactions are known to be implemented by Processes of diffusion. These form a homogeneous group of phenomena which become more readily understandable when viewed together, in that the knowledge gained from one serves to interpiet the next. It is the purpose of the present Paper to present, by means of examples drawn from practice, a brief survey of the ways in which gas-metal diffusion serves and obstructs the Purposes of the metal-fabricating industries. The selection of the cases described was made by consulting more than thirty-six practicing experts whose combined experience provided an extensive coverage of the field and who were in a position to supply examples of occurrences of present day interest. The response was generous and it is regrettable that space permits the description of only a limited number of typical examples with ' but brief mention of parallel cases. The Nature of Gas-metal Diffusion The term ugas-metal diffusion," although commonly used, is ambiguous in so far as it implies that a definite group of " substances may be identified as gases and may be expected to behave in a manner distinct from other substances in association with metals. "Gases" such as oxygen and hydrogen when diffusing through a liquid or solid metal are properly components of the liquid or solid solution; they behave as alloying elements and are not to be distinguished in their diffusion characteristics from other elements, except that each has an individual rate of diffusion. On the other hand, a number of metals in certain.temperature ranges are volatile to the extent that they may appear in the form of vapor in metallurgical operations. For the sake of greater definiteness, therefore, it will be convenient to regard as "gas-metal diffusion" any process in which the result depends upon one or more of the diffusing elements appearing, at some stage, in the gaseous state, or as a compound gas. NO element, gaseous or otherwise, can diffuse through a liquid or solid metal unless it is at least slightly soluble in that metal. The elements of low atomic number

Jan 1, 1944

By Arthur T. Allen

THE Kingsport formation, a part of the Knox dolomite of Ordovician age, is composed of 538 ft of dolomitc and limestone. Numerous bands, layers and nodules of chert, arenaceous and shale zones are present. The characteristics displayed by these features have been useful in mapping, prospecting and mining. Perhaps a better understanding of the origin of these zones will increase their usefulness. Introduction The presence of numerous bands, nodules, and irregular bodies of chert within the Kingsport formation in the Mascot locality has long been recognized. Oder and Miller1 mention the general characteristics, but do not deal with the chert occurrences in detail. When the occurrence of chert is studied in fresh exposures underground, a variety of characteristics is noted which has been useful in correlation and in detailing the sub-surface stratigraphy. Although the writer has no desire to enter into a controversy over the origin of chert, many observations have been made of its local characterigtics. A detailed stratigraphic section is included which shows the position of the individual horizons discussed in the following paragraphs. The term "chertification" has been adopted from Fowler and Lyden2 for use here. It refers to the replacement of lime- stone by introduced silicic acid. The writer uses it to refer to the occurrencc of introduced or original chert in limestone and dolomite. In this writing "syngenetic chert" refers to chert which has been deposited contemporaneously with the enclosing limestone or dolomite. Also, it is considered to include interstitial silica shown by chemical analysis and insoluble residues. The term "epigenetic" is applied to all chert which has been introduced after consolidation of the rocks in which it occurs, regardless of the nature of the depositing solutions. Syngenetic Chert It is the belief of the author that a large percentage of the chert found in the Kingsport formation is syngenetic. The widespread occurrence of similar nodules and bands of chert in the same horizon far from one another and far from areas of deformation or alteration of the enclosing rocks is difficult to explain by infiltration of the silica after compaction of the enclosing rocks. When chert of this type does occur near zones of movement it is likely to be involved in faulting and brecciation which indicates that it was deposited prior to deformation. Older Epigenetic Chert There are several occurrences of nodules in the Kingsport which seem to be epigenetic as pointed out in the following examples: A cherty zone occurs 26 ft above the o bed (Fig =). This is not always present but is found in the greater part of mine work-

Jan 1, 1949

By B. M. Larsen, W. E. Shenk

This paper describes a method of reversal control of the open-hearth furnace that obtains in practice those effects considered below as essential to a completely automatic control, without appreciable interference with the natural rise and fall in temperature of the regenerative portions of the furnace system. Growing out of some studies of radiation pyrometry in open-hearth regenerators, it was developed during 1934-1938, and has been successfully applied to a number of commercial furnaces. The goal of open-hearth furnace operation is the highest rate of production of steel of proper quality consistent with good refractory life and fuel economy. This requires rapid heat transfer from furnace to charge, which in turn is dependent upon heating the furnace refractories to the highest safe operating temperature. The greater the heat input to the melting chamber, the sooner this limiting temperature will be reached, so that control methods in general that are designed to protect against overheating of refractories should help to maintain maximum fuel input and production rate. For the typical open-hearth system, with fixed regenerator capacity and with rate of fuel input usually restricted in its range of variation, our basic assumption is the idea that the only other important variable —that is, the time interval between successive reversals—should also be held constant or within a small range. The present reversal control was designed therefore so that, under normal operating conditions, no arbitrary limitation is imposed other than to keep the reversal interval within the optimum time range. However, since a near approach to completely automatic operation involves protection of refractories through the balancing of furnace end temperatures as well as emergency protection against temperature peaks above some upper limit, it was also felt essential to employ, as an integral part of the control unit, a temperature-measuring instrument to register the true temperature of the refractory surfaces at some critical region in the hot ends of the regenerative zones. As the basic elements of the control, we thus have one "maximum" and one lLminimum" time relay and a potentiometer recorder-controller, combined with switches and relays to operate as follows: I. Reversal normally occurs within an optimum range limited by the maximum and minimum settings to about 4 to 6 min. variation, but the actual interval usually is less variable and closer to the minimum setting. 2. The margin between minimum and maximum time is utilized, together with a "floating temperature limit" in the potenti-ometric control instrument, to correct any tendency toward temperature unbalance between ends of the furnace. 3. A second "maximum temperature

Jan 1, 1945

By Nicholas J. Grant, John Chipman

A full understanding of the behavior of sulphur in the basic open-hearth process has been delayed by lack of dependable data covering a wide range of slag conditions in the absence of other complicating factors that are likely to be present under operating conditions. It has been generally accepted that strongly basic slags will dissolve more sulphur than will those in which the acidic and basic constituents are more nearly balanced. It has been known that both slag and metal would absorb sulphur from the flame when the sulphur content of the fuel is high. It has been generally believed that manganese assists in the transfer of sulphur from metal to slag. Almost nothing has been known of the effect of temperature upon desulphurization;the data have been conflicting and there has been a tendency to depend rather heavily upon analogy with the better understood desulphurizing reaction of the blast furnace. Many attempts have been made to build up from open-hearth data a satisfactory theory of the chemical reactions involved in the process. That this has been an extremely difficult task is owing to two reasons that have been very generally recognized. The first is the parallel and simultaneous reaction of sulphur transfer between flame and bath. The second is the difficulty of distinguishing between the factors that ultimately limit the transfer from metal to slag—i.e., equilibrium conditions—and those whose influence is only upon the rate of transfer. It has been the object of the work here recounted to study the equilibrium distribution of sulphur between slag and metal in the absence of these complicating factors, with the hope that a better understanding of the equilibria involved would lead to a better control of the over-all process in the open-hearth furnace. A review of the literature on steelmaking reveals almost complete agreement with respect to the paramount importance of lime in promoting desulphurization. In expressing this effect in quantitative terms, however, and in formulating the relationships between the concentrations of other slag components and the desulphurizing power, there is little agreement. For instance, the "basicity" or basic strength of the slag is commonly measured by some kind of ratio of concentration of basic to acidic oxides. Of these, the following have been reviewed by Schenck:20 V radio = % CaO/%SiO, Körber and Oelsen's _ % CaO'. 100/% CaO + % SiO2 where (%CaO') = % CaO- 1.18% P2O5. Herty's B ratio = % CaO - (0.93 . % SO2) - (1.18% P205) Among others there appear the following: 20 References are at the end of the paper.

Jan 1, 1947

By R. C. Ku, R. G. Davies

The stress-strain behavior of Fe-C and Fe-Ni solid-solution alloys has been investigated at 25°C. It is found that the rate of solid-solution strengthening is dependent upon the strain at which the yield stress is measured, the macroyield stress being much more concentration-dependent than the microyield stress. In fact the addition of nickel does not lead to any increase in the microyield stress of iron. The primary effect of increasing the carbon or nickel content is to increase the slope of the stress-strain curve in the microyield region; this effect has been correlated, by means of transmission electron microscopy, with a decreased ability of the dislocations to cross-slip. It is concluded that the Mott-Nabarro theory is a good description of true solid-solution hardening in these and other iron-base alloys. A.LL theories of the solid-solution strengthening1-4 indicate that the flow stress of an alloy increases both with solute concentration and "misfit" between the solvent and solute atoms. The functional relationship between strength, solute concentration, C, and misfit depends upon the particular theory. Mott and Nabarro1,2 and Schoeck and Seeger3 both predict a linear increase in strength with concentration, while Fleischer4 indicates that the strength should be proportional to C1/2; there are in the literature experimental observations to support both these compositional dependencies.1'8 The experimental evidence used to support the theories is the change in macroscopic yield stress (strain, e, = 10-3) with composition. However, recent investigations have revealed that solid-solution strengthening in a Cu-Al single crystals7 and in Fe-V polycrystal-line" alloys depends upon the strain at which the flow stress is measured; a flow stress in the microplastic range (e = 10-6 to 10-5) is much less concentration-dependent than the macroyield stress. Since the theories of solid-solution strengthening are concerned in particular with the stress to move a dislocation in a dislocation-free matrix, they should only be compared with microyield-stress data; it will be shown that in a material deforming homogeneously the microyield stress (e = 10-6) is approximately the stress to move through the matrix those dislocations which have been nucleated by stress concentrations such as particles or grain boundary ledges.9-11 In contrast, the macro-yield stress is more complex in that it is affected by several phenomena: dislocation multiplication, dislocation interactions, and the ease of propagating slip across grain boundaries. For example, it is experimentally observed that when long-range order12'13 or solute effects10 restrict cross alip the grain boundary

Jan 1, 1967

By B. M. Larsen, W. E. Shenk

THIS paper describes a method of reversal control of the open-hearth furnace that obtains in practice those effects considered below as essential to a completely automatic control, without appreciable interference with the natural rise and fall in temperature of the regenerative portions of the furnace system. Growing out of some studies of radiation pyrometry in open-hearth regenerators, it was developed during 1934-1938, and has been successfully applied to a number of commercial furnaces. The goal of open-hearth furnace operation is the highest rate of production of steel of proper quality consistent with good refractory life and fuel economy. This requires rapid heat transfer from furnace to charge, which in turn is dependent upon heating the furnace refractories to the highest safe operating temperature. The greater the heat input to the melting chamber, the sooner this limiting temperature will be reached, so that control methods in general that are designed to protect against overheating of refractories should help to maintain maximum fuel input and production rate. For the typical open-hearth system, with fixed regenerator capacity and with rate of fuel input usually restricted in its range of variation, our basic assumption is the idea that the only other important variable that is, the time interval between successive reversals-should also be held constant or within a small range. The present reversal control was designed therefore so that, under normal operating conditions, no arbitrary limitation is imposed other than to keep the reversal interval within the optimum time range. However, since a near approach to completely automatic operation involves protection of refractories through the balancing of furnace end temperatures as well as emergency protection against temperature peaks above some upper limit, it was also felt essential to employ, as an integral part of the control unit, a temperature-measuring instrument to register the true temperature of the refractory surfaces at some critical region in the hot ends of the regenerative zones. As the basic elements of the control, we thus have one "maximum" and one "minimum" time relay and a potentiometer recorder-controller, combined with switches and relays to operate as follows: x. Reversal normally occurs within an optimum range limited by the maximum and minimum settings to about 4 to 6 min. variation, but the actual interval usually is less variable and closer to the minimum setting. 2. The margin between minimum and maximum time is utilized, together with a "floating temperature limit" in the potentiometric control instrument, to correct any

Jan 1, 1945

By W. P. Saunders, W. R. Hibbard, G. H. Eichelman

Interest in the various products of the austenite eutectoid transformation in iron-carbon alloys, particularly as produced by the isothermal sub-critical techniques introduced by Davenport and Bain,' has resulted in the application of similar heat treatments to other eutectoid transformations. Studies o f the beta copper-aluminum alloy eutectoid transformation revealed microstructures very similar to those found in iron-carbon alloys. Investigations5t6 of the kappa phase in the copper-silicon alloy system have established the eutectoid type transformation of this phase into terminal alpha and intermediate gamma phases. This transformation has been reported5 as forming a eutectoid type structure in a very sluggish manner by a long time isothermal treatment. The purpose of the present investigation is to study the products of the kappa eutectoid transformation as affected by transformation temperatures by means of microscopic and hardness methods. Preparation of Alloys The copper-silicon alloy equilibrium diagram is shown in Fig 1. The kappa field converges to a minimum silicon solubility at the eutectoid composition and all other completely kappa alloys are hypereutec-toid. Thus, kappa decomposition involves first the proeutectoid precipitation of gamma, followed by the eutectoid transformation of a lower silicon content kappa (5.2 pct) Smith6 has indicated that alloys containing between 5.4 and 5.7 pct silicon could be hot rolled, but that the latter composition was desirable in order to permit a wider kappa temperature range. The alloy was prepared by adding Baker's commercially pure silicon to an ingot of copper-silicon alloy containing 2.34 pct silicon remaining from the investigation of Brick, Martin and Angier.' Following the casting techniques of Krynitsky, Saunders and Stern,s the ingot was melted under a heavy layer of dried charcoal in a clay-graphite crucible in a gas-fired pot furnace. Small lumps of silicon were held under thc melt surface with a graphite rod. After the silicon had dissolved, the alloy was chill-cast and then remelted without a cover, stirred thoroughly, skimmed and poured into a preheated cast iron mold. The cast microstructure is shown in Fig 2. The casting, 10 X 4 X K in., was annealed at 750°C for 21 hr and furnace cooled, About }{& in. was milled from all surfaces. The plate was cut in half longitudinally and the bottom half analyzed by A.S.T.M. and The composition by weight was as follows: copper 94.24 pct, silicon 5.56 pct, iron 0.11 pct.

Jan 1, 1949

By Nicholas J. Grant, John Chipman

A full understanding of the behavior of sulphur in the basic open-hearth process has been delayed by lack of dependable data covering a wide range of slag conditions in the absence of other complicating factors that are likely to be present under operating conditions. It has been generally accepted that strongly basic slags will dissolve more sulphur than will those in which the acidic and basic constituents are more nearly balanced. It has been known that both slag and metal would absorb sulphur from the flame when the sulphur content of the fuel is high. It has been generally believed that manganese assists in the transfer of sulphur from metal to slag. Almost nothing has been known of the effect of temperature upon desulphurization;the data have been conflicting and there has been a tendency to depend rather heavily upon analogy with the better understood desulphurizing reaction of the blast furnace. Many attempts have been made to build up from open-hearth data a satisfactory theory of the chemical reactions involved in the process. That this has been an extremely difficult task is owing to two reasons that have been very generally recognized. The first is the parallel and simultaneous reaction of sulphur transfer between flame and bath. The second is the difficulty of distinguishing between the factors that ultimately limit the transfer from metal to slag—i.e., equilibrium conditions—and those whose influence is only upon the rate of transfer. It has been the object of the work here recounted to study the equilibrium distribution of sulphur between slag and metal in the absence of these complicating factors, with the hope that a better understanding of the equilibria involved would lead to a better control of the over-all process in the open-hearth furnace. A review of the literature on steelmaking reveals almost complete agreement with respect to the paramount importance of lime in promoting desulphurization. In expressing this effect in quantitative terms, however, and in formulating the relationships between the concentrations of other slag components and the desulphurizing power, there is little agreement. For instance, the "basicity" or basic strength of the slag is commonly measured by some kind of ratio of concentration of basic to acidic oxides. Of these, the following have been reviewed by Schenck:20 V radio = % CaO/%SiO, Körber and Oelsen's _ % CaO'. 100/% CaO + % SiO2 where (%CaO') = % CaO- 1.18% P2O5. Herty's B ratio = % CaO - (0.93 . % SO2) - (1.18% P205) Among others there appear the following: 20 References are at the end of the paper.

Jan 1, 1947

By R. M. Brick

SEGREGATION can occur only in cast alloys that solidify over a range of temperatures with a difference in composition of liquid and solid phases within this range (ignoring monotectic systems and chemical reactions as in rimming. steels). Thus a pure binary eutectic alloy should show no segregation unless undercooling occurs for one of the solid constituents of the eutectic; e.g., chill-cast Al-12 per cent Si alloys. The phasial condition implicitly described above-solidification over a range of temperatures with a compositional difference between solid. and liquid-is found in nearly all solid solutions or combinations of solid solutions and eutectics. Metastable conditions of solidification of these types of alloys cause coring; i.e., a difference in composition between the center of a dendrite and its periphery. This composition gradient can be detected usually only by microscopic examination of etched structures; it is a "micro" effect. The gradient of more immediate industrial concern is that between the center of a cast section and the surface layers. This gross (macro) effect is usually determinable only by sampling of the casting at different points, with chemical analyses of each sample. If the compositional difference is of the same type as in coring, the first parts to freeze being enriched in higher-melting-point constituents, and vice versa, the effect is called normal segregation. When what is apparently the first part of the casting to solidify shows a higher concentration of low-melting-point constituents, the effect is called inverse segregation. These macro effects are quite separate from the micro effect, coring, yet the latter must be. described first because it is an essential part of the picture. CORING Solid Solution, Ni-Cu The nickel-copper phase diagram is reproduced in Fig. Ia, in which the solid lines represent the equilibrium liquidus 1, 3, 7 and solidus 2, 5, 8, and where the vertical 1, 4, 8 represents a 55 per cent Cu alloy. Upon moderately rapid solidification, the first dendritic axes of composition 2 (see Fig. 1b) start to form at a temperature somewhat under I. Solidification continues by growth of the dendritic nuclei, but at temperature 4 the increment solidifying is of composition 5. The rapidity of this crystal growth prevents diffusion of nickel and copper atoms from adjusting the composition of the entire dendrite at 5, which it would be under equilibrium conditions. The average composition of a specific dendrite, or the entire solid phase, at temperature 4 might be that indicated

Jan 1, 1944

By J. J. Taber, I. S. K. Kamath, R. L. Reed

Alcohol floods of consolidated sandstone cores have shown the process to be strongly dependent on the phase behavior of the particular alcobol-oil-water system used. This means that in many cases the mechanism does not conform to the idea of a piston-like displacement. Instead, it is found that by changing the alcohol it is possible to change the relative velocities of the oil and water and, in fact, the entire mechanism of the process. The effects of rate, viscosity, initial saturation, distance travelled and hysteresis of relative permeability on the alcohol flooding mechanism are discussed. INTRODUCTION Reasons for interest in the use of alcohol to miscibly displace oil and water from a porous medium appear in the existing literature.l-7 The mechanism of the displacement has been considered and the apparent implications formulated into a theory which presumably would enable one to predict the essential features of the process.6 Unfortunately, most of the reported experiments have been performed with unconsolidated or artificially consolidated sands. With these systems some of the noteworthy facets of the process are obscured and resulting data appear uncertain. It is the purpose of this paper to show how the use of consolidated sandstones has led to revision of the mechanism and, hence, the theory of alcohol flooding. The practical result is increased pessimism toward the possibilities of commercial application of the simplest form of the alcohol-slug process. However, elucidation of the mechanism has made it possible to define the essential characteristics of a system of slugs which will behave in a nearly piston-like fashion and, thus, yield the best possible result. EQUILIBRIUM PHASE BEHAVIOR Fig. 1 is a diagram of the ternary system isopropyl alcohol (IPA)-Soltrol-calcium chloride brine. Brine was used to prevent plugging of the core and calcium chloride was used because sodium-chloride brine exhibits a solid phase with Soltrol and IPA. If alcohol is added in increments to the immiscible mixture of water and oil represented by Point A, the path followed by the successively equilibrated samples will be on the Line ABC and pass from the immiscible region to the miscible region by crossing the binodal curve at B. Consider the intersection D of this path with the tie Line EF. The quantity of oleic phase is proportional to the Segment ED and the quantity of the aqueous phase is proportional to DF. Compositions of the two phases are specified by Points E and F. It is clear that in the case shown the oleic phase is diminishing and entirely disappears when miscibility is achieved. Such will

By William H. Spice

Exploratory drilling in South Central Texas for the year 1944 showed a marked increase over that of 1943 and resulted in a similar increase in new fields discovered. In this area, which comprises the 30 counties included in district No. I, Oil and Gas Division, Railroad Commission of Texas,? 61 exploratory wells were drilled during 1944 as compared with 29 exploratory wells drilled during 1943, or an increase of over 100 per cent. Three new oil fields, two new gas fields and one gas-distillate field were discovered during the year, as compared with one new oil field and one new gas field discovered during 1943. These new fields were the result of exploratory drilling throughout the district along the Wilcox trend and the deeper Edwards lime trend, which was started during the previous year. The Wilcox trend yielded the new Loma iilta-Wilcox oil field and the San Caja gas-* tlistillate field, both in McMullen County. The Charlotte field, in Atascosa County, was discovered along the deeper Edwards lime trend. These three discoveries were of considerable importance and subsequent development should indicate the desirability of continued exploration along these trends. The other three discoveries, United oil field in Guadalupe County, Pederson gas field in Milam County and Van Cleve gas field in Zavalla County, were of minor importance. Charlotte Field, Atascosa County, was discovered by the Humble Oil and Refining Company's No. 3 Pruitt, completcd on Aug. 9, 1944, flowing 176 bbl. per day, 3/16-in. choke, 710 lb. tubing, 475 lb. casing pressures, 37.7º A.P.I. gravity, from the top of the Edwards lime from 6917 to 6923 ft. Two oil wells were completed during the year in this field. This discovery is 14 miles southwest of the same company's Imogene field, also producing from the Edwards lime but with considerable difference in reservoir characteristics. The discovery of this field is the result of surface geology and subsequent seismograph survey of the area. Loma Alta-Wilcox Field, McMullen County, was discovered by the Atlantic Refining Company's No. I Atkinson, completed on June I, 1944, flowing 102 bbl. per day, 9/64-in. choke, 1900 lb. tubing pressure, 37º A.P.I. gravity, from Wilcox sand from 6866 to 6869 ft. after being drilled to a total depth of 7185 ft. This discovery is the result of subsurface geology and an extensive seismograph survey of the entire area. Sun Caja Field, McMullen County, was discovered by Edwin M. Jones No. 2-C Ezzell, completed on June 2, 1944 as a dual completion in the Wilcox sands, flowing 1,740,000 cu. ft. gas with 53 bbl. distillate, 1/4-in. choke, 2035 lb. tubing pressure, 53.2º A.P.I. gravity, from sand 6416 to 6453 ft. and flowing 2,000,000 cu. ft. of gas with 127 bbl. distillate, 1/4-in. choke, 2500 lb. tubing pressure, 50º A.P.I. gravity, from sand 6889 to 6916 ft., after being drilled to a total depth of 7264 ft. Three gas-distillate wells were completed during

Jan 1, 1945

By John T. Galey

The outstanding developments of the year in southwestern Pennsylvania were the establishment of the Summit Fayette County gas pool and the gas pool in Nicholson township, Fayette County, and Monongahela township, Greene County, as major producing areas, and the indication of four new shallow gas pools. Curtailment of drilling for shallow gas is expected to follow order M68 of the Office of Production Management. Gas completions were approximately 70 per cent higher, oil completions nearly 25 per cent lower, dry holes were unchanged and drilling wells as of Dec. 31, 1941, nearly loo per cent higher than last year. Shallow Development Oil.—Outside Butler County, only 11 producers were drilled, with a total initial of 221 bbl. The best of these was in a portion of Gilmore township, Greene County, which ordinarily produces gas. This well flowed 77 bbl. in 11 hr., along with about one million cubic feet of gas from the Fourth (U.Dev.) sand. Washington County had a 10.20 and a 25-bbl. well in Morris township and a 20-bbl. well in South Franklin township. These were all in the Fifth Sand. The price of oil to Jan. 27 was $1.80 per barrel, when a 15¢ increase was made. This was followed by a raise of 20¢ on Apr. 23, 15¢ on May 21, 20¢ on June 18 and 25¢ on Aug. 14. The last increase was canceled on Aug. 23 by the Office of Price Administration, which pegged southwestern Pennsylvania crude at $2.40 per barrel. Gas.—An almost doubled initial production of natural gas is the result of the large increase in number of wells drilled. The outstanding discovery of the year was in the vicinity of Armbrust, Hempfield township, Westmoreland County, where a well drilled to what at first was considered the Bayard sand, but what is now known to be the Fifth (U.Dev.) sand, at 2100 ft. found nearly 5 million cu. ft. of gas. Since this completion 14 wells have been finished, only one of which was dry, giving a combined total open flow of approximately 15 million cu. ft. The sand is 35 to 40 ft. thick and the saturation extends through most of that thickness. Rock pressure, which is 1040 lb. per sq. in., is abnormally high. An area of only about one square mile has been proven but some of the 24 new wells drilling as of Dec. 31 will no doubt extend it considerably. This development has taken place in an area heretofore considered to have had little prospect. There were three good wells in other parts of Westmoreland County. One well in Franklin township, which had 12 million cu. ft, of gas in the Fifth sand, was entirely surrounded by dry holes but is still pro- . ducing at a high rate. In Bell township a 1.6 million cu. ft. well was found in the Speechley (U.Dev.) sand and in Washington township the same sand produced 2.7 million cu. ft. with shut-in pressure of 970 Ib. at 2820 ft. This well is offset by two dry holes and one well with a capacity of only 10 M cubic feet.

Jan 1, 1942

By R. C. Amero

FULLERS earth is a general name applied to claylike minerals that have high natural ad-sorptive powers. They are usually distinguished from ordinary clays by a higher content of combined moisture and a lower apparent density. The definition is based on the ancient use of the material for fulling, or cleansing woolen cloth of oil and grease; a more modern definition should mention the ability to decolorize oil and should differentiate between fullers earth, which is naturally active, and certain bentonites which only develop decolorizing power after being leached with strong mineral acids. The distinction between fullers earth and activable bentonite is not a sharp one, since all types of intermediate clays can be found that are more or less naturally active, yet more or less responsive to acid treatment. The differences seem to depend somewhat on the amount of leaching that has been effected by natural ground waters. Physical Properties The principal mineral constituent of activable bentonite is montmorillonite, a hydrous aluminum silicate to which the following formula is generally assigned: Al,Si,O,, (OH), • 12H,O Fullers earth, as well as bentonite, is usually composed of some variety of montmorillonite, but in the United States the largest tonnage of fullers earth is mined from deposits of attapulgite. Attapul- gite is a clay mineral composed of monoclinic crystals of colloidal size, having a fibrous shape similar to that of asbestos. A sectional model of the attapulgite "molecule" is shown in Fig. 1. A single unit is about 18.0 A wide and 12.9 A high. The length of the molecule is variable, but this same molecular pattern is repeated to form needlework crystals, rather than flakes, as is characteristic of the montmorillonite crystals. Attapulgite has been assigned the following formula,' although actually, the magnesia has been largely replaced by alumina: (0%) . (OH), • Mg, . Si, • Olp . 4H20. The fibrous nature of the mineral is clearly shown in the electron micrograph, Fig. 2. Although the deposits contain 5 to 30 pct quartz and carbonate minerals, impurities in the commercial products are held at a low level, principally by selective mining on the basis of oil decolorizing efficiency. The particle size distribution of this fullers earth has been estimated from settling rates, using sodium citrate as a dispersing agent.' Since Stokes' law only applies to spherical particles, the equivalent particle diameter calculated below is probably more nearly an index of diameter rather than length of the needlelike crystals: Eqnivalent Arbitrary Particle Distribution, Size Diameter Pci Classil3catian 0.05 mm 0.80 0.80 pct sand 0.05-0.02 mm 10.96 0.02-0.01 mm 9.65 42.10 pct silt 0.01-0.005 mm 11.40 0.005-0.002 mm 10.09 2-0.5 micron 10.61 0.5-0.2 micron 29.09 56.58 pct clay 0.2-0.05 micron 14.86 0.05 micron 1.96 The differential thermal analysis shown in Fig. 3 is unique and supports the theory that this is a distinct mineral species.' ~ Other general properties of the mineral as shown in Table I.

Jan 1, 1952