Search Documents

By A. W. Hesse

VENTILATION of all types of coal mines is fundamentally the same, in that sufficient air must be provided to properly dilute and remove dangerous and obnoxious gases and leave the oxygen content of the air not under 19 per cent in all places where men and animals must work. Perhaps animals should not be mentioned, as the speed of mechanical loading leaves livestock behind and outmoded. Since this paper has to do with the influence of mechanical loading equipment on ventilation, the problems will be confined to the splits and the coal-producing places of the mine. The removal of coal dust from the air, or its rapid transmission to the return air courses; the possible increase in the liberation of gases by the multiplication of cuts in the coal made during one shift or multiple shifts; and the additional electrical equipment at the faces, are the factors that cause the added importance to good ventilation in the permissible equipment area of gassy bituminous coal mines. VENTILATION FOR MECHANICAL LOADING IN GASSY MINES In gassy mines, the air currents must be maintained across the faces in such a way as to prevent short cuts to the returns and leaving pockets in which accumulation of gas might occur. To do this, two or more doors are required on almost every entry containing a track to the face, so located that in no event will a trip of cars block open the doors and permit the air to by-pass some place or places on the air-approach side. This method frequently requires the use of unusual lengths of duplex cables to reach the mechanical equipment at the faces, particularly where the distances between parallel working places are 100 ft., as at the Nemacolin mine. Fig. I shows a pillar section being worked with mechanical loaders. This layout requires carrying the air in on the right and releasing it on the left, because the track clearance is on the right side and the line brattice is built on this side from the last crosscut to the face. Thus, the air travels to the face with greater velocity, and gives more assurance of sweeping out the gas that might be exuding from the crevices of the coal. All working places, in driving through solid coal, are thus treated alike. They are all potentially gassy and must be swept clear of whatever may contaminate the air. Once the air starts into the working section, it is not released until it does a good job. Of course the volume of air must be large enough not only to dilute the gases but to carry away explosive fumes and fine coal dust quickly. Mechanical loading entails cutting and drilling of the coal during the same working period as the loading when two-shift and three-shift operations are employed, and all three processes create finely pulverized coal, which in itself is hazardous if not controlled by some means. If the ventilation is inadequate and gas accumulates, and a spark from defective electrical

Jan 1, 1941

By John T. Galey

The outstanding developments of the year in southwestern Pennsylvania were the establishment of the Summit Fayette County gas pool and the gas pool in Nicholson township, Fayette County, and Monongahela township, Greene County, as major producing areas, and the indication of four new shallow gas pools. Curtailment of drilling for shallow gas is expected to follow order M68 of the Office of Production Management. Gas completions were approximately 70 per cent higher, oil completions nearly 25 per cent lower, dry holes were unchanged and drilling wells as of Dec. 31, 1941, nearly loo per cent higher than last year. Shallow Development Oil.—Outside Butler County, only 11 producers were drilled, with a total initial of 221 bbl. The best of these was in a portion of Gilmore township, Greene County, which ordinarily produces gas. This well flowed 77 bbl. in 11 hr., along with about one million cubic feet of gas from the Fourth (U.Dev.) sand. Washington County had a 10.20 and a 25-bbl. well in Morris township and a 20-bbl. well in South Franklin township. These were all in the Fifth Sand. The price of oil to Jan. 27 was $1.80 per barrel, when a 15¢ increase was made. This was followed by a raise of 20¢ on Apr. 23, 15¢ on May 21, 20¢ on June 18 and 25¢ on Aug. 14. The last increase was canceled on Aug. 23 by the Office of Price Administration, which pegged southwestern Pennsylvania crude at $2.40 per barrel. Gas.—An almost doubled initial production of natural gas is the result of the large increase in number of wells drilled. The outstanding discovery of the year was in the vicinity of Armbrust, Hempfield township, Westmoreland County, where a well drilled to what at first was considered the Bayard sand, but what is now known to be the Fifth (U.Dev.) sand, at 2100 ft. found nearly 5 million cu. ft. of gas. Since this completion 14 wells have been finished, only one of which was dry, giving a combined total open flow of approximately 15 million cu. ft. The sand is 35 to 40 ft. thick and the saturation extends through most of that thickness. Rock pressure, which is 1040 lb. per sq. in., is abnormally high. An area of only about one square mile has been proven but some of the 24 new wells drilling as of Dec. 31 will no doubt extend it considerably. This development has taken place in an area heretofore considered to have had little prospect. There were three good wells in other parts of Westmoreland County. One well in Franklin township, which had 12 million cu. ft, of gas in the Fifth sand, was entirely surrounded by dry holes but is still pro- . ducing at a high rate. In Bell township a 1.6 million cu. ft. well was found in the Speechley (U.Dev.) sand and in Washington township the same sand produced 2.7 million cu. ft. with shut-in pressure of 970 Ib. at 2820 ft. This well is offset by two dry holes and one well with a capacity of only 10 M cubic feet.

Jan 1, 1942

By Ernest L. Ohle

The newly opened Hayden Creek lead mine represents a variation from the usual Southeast Missouri type. Galena mineralization occurs in sandy dolomite cementing a conglomerate of granite boulders and in cracks in the boulders. The conglomerate occurs at the base of the Bonneterre formation on the slopes of two buried pre-Cambrian knobs. IN 1943 diamond drilling from the surface in an area 2 miles southwest of Leadwood, Mo., discovered a lead deposit of a markedly different character from the usual southeast Missouri type. Subsequent drilling of about 500 holes indicated several million tons of ore, and in 1950 a 701-ft vertical shaft was sunk into the orebody. This paper describes the geology of this interesting occurrence insofar as it is known from the drilling and the small underground exposure at the bottom of the shaft. Geology The location of the Southeast Missouri Lead Belt and of the Hayden Creek property are shown in Fig. 1. As shown here, there are two separate producing areas, one from which the larger tonnage has come, located near Bonne Terre, Flat River, Desloge, and Leadwood, and the other to the south around Fred-ericktown and including famous old Mine LaMotte. The best published description of Lead Belt geology is by Tarr.* In pre-Cambrian time in this area, an assemblage of granites and rhyolitic flow rocks was eroded to a mature topography. Sedimentation, beginning in the Upper Cambrian, filled in the valleys and gradually covered even the highest hills. The first formation deposited was the La-motte sandstone; it is successively overlain by the Bonneterre dolomite, the principal lead-prodbcing formation, then the Davis shale. the Derby-Doerun limestone, and a succession of Cambro-Ordovician cherty dolomites. Several of these formations may be found in direct contact with the pre-Cambrian as their deposition progressively overlapped the older rocks on the flanks of the igneous knobs and ridges. Immediately overlying the pre-Cambrian there is, not uncommonly, a thin basal conglomerate of granite or porphyry boulders, which is incorporated into the overlying sediments. Deposition of the lower part of the rock section was fairly continuous, and the Lamotte sometimes grades almost imperceptibly into the lower sandy Bonneterre. Since the sediments were deposited on an uneven floor, they tend to reflect the irregularities in that floor. Most of the steep dips found in the district, that is, dips in excess of 10°, are original dips and not caused by deformation. Such domelike structures in the sedimentary rocks around the igneous knobs have localized a considerable number of the orebodies in the district and particularly those in the Frederick-town area. Many of the larger orebodies, however, have no close relation to the pre-Cambrian topography. Most of the lead production has come from the lower 150 ft of the Bonneterre formation, where disseminated ore spreads laterally parallel to the bedding for great distances. Average stoping height is about 20 ft, but in a few places there are stopes over 175 ft high.

Jan 1, 1953

By B. Blumenthal

THE present investigation was planned as a survey of the lead-rich portion of the ternary lead-antimony-silver system by thermal analysis. Since, however, a rigorous application of the conventional thermal analytical method is time consuming, an attempt was made to speed up the investigation by reducing the time required for a single thermal analysis. This was done by increasing the rate of cooling to 12° to 18°C. per minute, since such a rate does not permit even an approach to equilibrium conditions, the melt was stirred vigorously by a stirrer operating at the high rate of 665 r.p.m. This proved to be effective in obtaining cooling curves with distinct points of arrest and of excellent reproducibility, which satisfactorily compare with those obtained at a rate of 1" to 2°C. per min. with or without slow stirring (Fig. I). By this method the lead-rich end of the lead-alltimony system and a series of ternary alloys in sections parallel to the lead-antimony side of the ternary system were investigated and it was observed that the two branches of the liquidus curve of the binary alloys did not intersect at the euteotic temperature. An equivalent effect mas observed in the ternary system. The eutectic temperature of the binary lead-antimony system was found to be 252.0°C., which confirms the recent in- vestigation by Pellini and Rhines,1 who determined the eutectic temperature to be 2 51.5°C. The observation that the curves of primarY crystallization of the lead-antimony system do not intersect at the eutectic temperature was previously made by Dean.2 Dean explains the phenomeilon by assuming the existence of a compound Sb4pb. He felt that supercooling was not the cause of the phenomena because he was unable to influence them by inoculation. The X-ray investigation by Solomon and Morris-Jones,3 the metallographic investigations by Stead,4 Charpy,5 Gontermann,6 and Dean, Zickrick and Nix,7 and the numerous investigations of physical properties, definitely disprove the occurrence of any compound. The work of Dean was not confirmed by Broniewski and Sliwoski,8 whose experiments did not show any irregularity and who report a eutectic composition of 13 per cent antimony and a eutectic temperature Of 2500 to 252°C. at a rate Of coo1ing of about 6°C. Per min. Abell Redlich and Adler9 then report a eutectic composition of 12.1 per cent upon reviewing the previous publications and adding a few of their own cooling curves. In 1934 Quadrat and Jiriste10 found from careful analyses of the bottom portion of slowly cooled hypereutectic melts that the eutectic only 11 .4 to 11.5 per cent antimany. (Previous analyses by Stead4 .in 1891 gave 13 per cent.) Weaver,ll however, reported in 1935 that cooling cunres indi-

Jan 1, 1944

By J. M. Bugbee

The engineer and the conservationist agree that effective water drive is the desirable reservoir production mechanism. Water drive may result either from the expansion of edge water, the reservoir water bordering an oil pool, or from the artesian flow of edge water from the outcrop. Thus, the extent of the reservoir has an important bearing upon both the rate and the ultimate quantity of water influx to an oil pool. Lens-type reservoirs are generally recognizable, but the complete structure of the more important domal types, having possible limitations from crestal and synclinal faulting, is not well understood. The delineation from cores, electrical logs and exploitation phenomena of the crestal portions of reservoirs is increasingly exact. This paper suggests that inference from these factual pictures, combined with the scattered well and geophysical data of the synclines and with consideration of the dynamics of structural formation, may be applied to solving the complete geologic structure. Since faulting on the domes and in the synclines may effectively seal and thus limit the size of a reservoir and bar additional water influx, consideration of geologic structure and its possible effects is essential to complete analysis and prediction of reservoir performance. Introduction Implicit in reservoir studies is the fact that the oil must be displaced from the reservoir rock by some other fluid, either gas or water, and this understanding yields the terms descriptive of the major reservoir production mechanisms, gas expansion and water drive' Three recent papers1-2-3 make clear the economic and conservation preeminence of Water drive as a production mechanism; in fact, the title of the latest of these is " Production under Effective Water Drive as a Standard for Conservation Practice." There appears to be an assumption at times among analysts that the effectiveness of a water drive is solely dependent on the rate of oil production; that is, if water drive appears to be insufficient or lacking, a lower oil-recovery rate would increase or reveal it. This assumption might result from the fact that the analysis has been wholly developed during the period of production curtailment; that is, since 1929. The writer takes it that the recurrent phrase in De Golyer's paper,3 "some degree of water drive," is related to this assumption. In California, an extraordinary phrase, "inactive water drive," is rather common and the connotation of uncertainty regarding our knowledge of reservoir performance is evident. Wyckoff2 speaks of the type of reservoir and performance as follows: "In general, reservoirs may be any one or a combination of domal, faulted, lenticular, or stratigraphic traps. Insofar as the dynamic performance of such reservoirs is concerned, the particular type merely determines whether regional flow is symmetrical as in a uniformly developed domal or lenticular type, or one-sided as in many stratigraphic or faulted traps." But whether the flow is

Jan 1, 1943

By Charles A. Anderson

The Bagdad copper deposit is of the disseminated type (porphyry copper) occurring in a quartz monzonite stock of late Cretaceous or early Tertiary age. This stock, located essentially at the intersection of two dike swarms, is the only one of several stocks cropping out in the area which is appreciably fractured and mineralized. Most of the rocks in the area are of pre-Cambrian age, but their structures have had no discernible influence on the copper mineralization. Hypogene alteration of the quartz monzonite includes the addition of quartz, orthoclase, and sericite and recrystalli-zation of biotite. The hypogene sulphides are pyrite, chalcopyrite, and molybdenite, the latter younger than the chalcopyrite. The late Cretaceous or early Tertiary igneous rocks, veins, and faults were controlled by northeast and northwest shear zones, the intersection of which marks the zone of appreciable copper mineralization. The minor mineralized fractures carrying the bulk of the copper have a preferred orientation parallel to the intersecting shears, and it is concluded that they are of tectonic origin rather than the result of shrinkage on cooling, crystallization, or mineralization. Supergene enrichment during late Tertiary or early Pleistocene time formed a chalcocite zone providing the minable copper ore. The enrichment was controlled in large part by northeast and northwest faults, prticularly at their intersection or where the faults are closely spaced. Introduction A major objective in a regional geologic study of a mining district is to determine whether any structural pattern can be found that has a bearing on the control of mineralization. The Bagdad copper deposit is of the disseminated type (porphyry copper) occurring in a.quartz monzonite stock which is located essentially at the intersection of two dike swarms (Fig 2). Of several quartz monzonite stocks in the area only this One is appreciably fractured and mineralized. The origin of the minute mineralized fractures in disseminated copper deposits has long been a challenging problem to the mining geologist, and evidence has been obtained to suggest that the mineralized fractures at Bagdad are related to a regional pattern of conjugate shears which also controlled the location of the dike swarms. The purpose of this paper is to Present this evidence and to emphasize the structural control of the supergene enrichment in forming a chalcocite zone that has provided the ore for the Bagdad mine. The field work on which these conclusions are based was done between October 1943 and August 1945, as a part of the copper investigations of the Goelogical Survey, U. S. Department of the Interior. The writer and his associates, E. A. Scholz and J. D. Strobell, Jr., have prepared a comprehensive report on the geology and ore deposits of the Bagdad area which will be published subsequently by the Geological Survey. Bagdad is located in west-central Arizona in Yavapai County. Ransome' divided the State of Arizona into three provinces: I? the plateau to the northeast; 111, the desert region to the southwest and 11, the moun-

Jan 1, 1949

By G. R. Rubly, H. J. Steele

The San Manuel property is in town&ips 8S and 9S, range 16E, Gila and salt River Base and Meridan, State of Arizona. This area is in the Old Hat mining district, southern pinal county, and is about 31/25 miles southwest of the town of Mammoth on the San Pedro River And one mile south of the Mammoth mine at Tiger, Arizona, The property consists of over 150 contiguous lode claims. The old Hat district was prospected prior to the civil war, but there was little or no production until 1881.1 The chief producers have been the Mammoth and Mohawk mines, now consolidated and operating as the st. Anthony Mining and Development Co., Ltd. Production to 1936 was $5,200,000, of which 83 pet was gold.2 Since 1940 the production has been chiefly lead and zinc, and some molybdenum and vanadium. There are a few small properties in the vicinity that have produced very minor tonnages of copper ore. In the San Manuel group there are claims which have been held continuously from 1906 to the present time, and at least two churn-drill holes were put down on or near the outcrop in 1917. No logs for these holes are available, but it is assumed that the grade of copper encountered was not sufficient to encourage further exploration. A small amount of ore has been shipped from open cuts on the San Manuel outcrop area, but there is no record of the tonnage Or grade. It is estimated that not more than 50 tons were mined. These cuts, plus a few shallow shafts and some short adits indicate limited and unenthusiastic prospecting at San Manuel. In 1942, through the efforts of James M. Douglas, R. B. Giffin, Victor Erickson, and Henry W. Nichols, owners of the Sari Manuel group, the Reconstruction Finance Corporation and War Production Board authorized the United States Geological Survey to investigate the property, and by their recommendation, the United States Bureau of Mines was authorized to put down a limited number of churn-drill holes. The Bureau of Mines carried On drilling from November 1943 to February 1945 Seventeen holes were drilled, varying from 305 to 1990 ft in depth. The property was brought to the attention of Magma Copper Co. in June 1944, and an option agreement was made with the Owners. Subsequently, a group of claims lying north of the original group and held by the Apex Lead Vanadium Mining Corp, and a group to the east held by the Quarelli family, were optioned. A drilling program was laid out to conform to the Bureau of Mines pattern, and drilling started in December 1944 Sari Manue1 Copper Corp. was incorporated September 1945, and has carried on the exploration program to the present time. Geology General The mineralized outcrop, chief copper mineral of which is chrysocolla, is a tri-

Jan 1, 1949

By James F. Watson, Jack L. Christian

The austenite to martensite solid state phase transformation in the 300 series austenitic stainless steels was studied over the temperature range of 788° to -423°F. The primary variables controlling this transformation are temperature, plastic strain, and chernical composition. Consequently, temperature effects were studied by measurements at 78", -100°, -320°, ad -423°F; plastic strain was controlled by cold-rolling the alloys varying amounts between 40 and 80 pet; and chemical compositions were varied by using 301, 302, 304 ELC, and 310 stainless steel alloys which exhibit varying degrees of austenite stability. The martensite contents of various alloys were correlated with several mechanical properties including yield and ultimate tensile strength, elongation, and notched tensile strength (Kt = 6.3). The yield and tensite strengths generally increased with increasing martensite content, but ) no correlation was observed between elongation and martensite content. The notched/un-notched ratio (Kt = 6.3) at -423°F exhibited a maximun at about 65 pct martensite. Attempts to correlate austenite stability (as measured by the Ms temperature) with both martensite content, and incremental increases in martensite content resulting from tensile testing were generally unsuccessful because the variable of cold Work could not be separated. As a result, only a general correlation of these variables was obtained. A (111) pole figure of austenite in a cold-rolled 301 stainless steel mas prepared an attempt to further investigate directionality as exhibited by mechan- ical properties. Yield strength was correlated with this pole figure, but ultimate and notched tensile strengths were not. 1 HE literature contains a wide variety of references pertaining to the austenite to martensite solid state phase transformation in austenitic stainless steel, see references 1 through 18. Discussions of the crystallography and kinetics of this transformation are given in references 2, 7, 8, 'and 11, while further discussions of austenite stability and hardening mechanisms are given in references 1, 3, and 10. Two important processing variables involved in this reaction are the degree of cold work and the temperature at which cold work is performed, and the nature of these effects are outlined in references 4 and 12, and 15 and 16 respectively. The latter two references deal primarily with cold rolling conducted at subzero temperatures. The effect of chemical composition on the austenite to martensite reaction was treated in detail by Eichelman and Hull, and they determined an equation for the M, temperature of this type of steel which included the effects of nickel, chromium, carbon, nitrogen, silicon, and manganese.5 Previous studies have shown that austenitic stainless steels of AISI types 301, 302, 304ELC, 310, and 301-N exhibit mechanical properties between 78" and -423"~ that are microstructure dependent, and the dependence of this microstructure on chemistry, temperature, tensile stress, and prior deformation is in general accord with previous investigations which have measured the effects of each of these variables on structure, or more specifically, the austenite-to-martensite transformation.lg The behavior of fully stable alloys, such as ATST type 310, at cryogenic temperatures is

Jan 1, 1962

By R. W. Kraft, F. D. George, F. D. Lemkey

From a conszderation of the geometrically possible ways in which an array of lines or linear features in three-dimensional space can depart from a statistically random arrangement, a system was developed to describe and measure different types of anisotrypic arrangements of lines in opaque solids. The technique was applied to a specimen of unidirectionally solidified Al-Cwll, eutectic which contained microstructural imperfections termed lamellar faults. Experimental data obtained from photomicrographs of different facets of a grain of this alloy were then analyzed using this system. It was deduced that the defects, which are essentially linear in natuve, were predominantly parallel to one another but not parallel to the nominal growth direction probably because of some lateral heat flow during solidification. InGOTS of lamellar eutectic alloys which have been unidirectionally solidified under growth conditions which prevent colony formation consist of large elongated grains in which the lamellae are approximately parallel to one another. Deviations from a parallel lamellar structure within a grain are caused by extra lamellae which form occasionally during the solidification process. Three-dimensional analyses of such specimens have revealed that one extra platelet produces two defects, termed 1amellar faults, which can and do grow more or less independently of one another.' The faults are analogous in many ways to edge dislocations in crystals. If a lamella of one phase is considered to be basically two-dimensional, e.g., a surface, then a fault can be defined as the locus of points which delineates an edge (or half the periphery) of one extra lamella as it grows and forms bridges and saddles in an otherwise parallel arrangement oi lamellae, Fig. 1. Were it not for the fact that bridges and saddles occur in the structure, the extra platelet could be defined as the unit defect and the concept of linear faults of positive and negative character around the periphery of the extra platelet would be unnecessary. If an extra platelet is merely inserted (actually it is grown in) between other parallel platelets, the fault line around the periphery of the extra platelet would circumscribe one and only one platelet, namely the extra one, and the faults would lie in a plane parallel to the lamellae. But when an extra platelet merges with adjacent ones and each side grows independently of the other, it is no longer topologically possible to delineate "the extra plate." A fault circuit which either closes on itself or passes out of the specimen still occurs although it no longer will be coplanar with the lamellae. In fact, it is usually not even Planar even if the lamellae are. Under these conditions a concept that a specimen contains N extra platelets of a given size per unit volume would be very artificial and consequently meaningless. Therefore, because of the topological complexity of the alloys, it was deemed necessary to define one-dimensional

Jan 1, 1962

By J. M. Bugbee

The engineer and the conservationist agree that effective water drive is the desirable reservoir production mechanism. Water drive may result either from the expansion of edge water, the reservoir water bordering an oil pool, or from the artesian flow of edge water from the outcrop. Thus, the extent of the reservoir has an important bearing upon both the rate and the ultimate quantity of water influx to an oil pool. Lens-type reservoirs are generally recognizable, but the complete structure of the more important domal types, having possible limitations from crestal and synclinal faulting, is not well understood. The delineation from cores, electrical logs and exploitation phenomena of the crestal portions of reservoirs is increasingly exact. This paper suggests that inference from these factual pictures, combined with the scattered well and geophysical data of the synclines and with consideration of the dynamics of structural formation, may be applied to solving the complete geologic structure. Since faulting on the domes and in the synclines may effectively seal and thus limit the size of a reservoir and bar additional water influx, consideration of geologic structure and its possible effects is essential to complete analysis and prediction of reservoir performance. Introduction Implicit in reservoir studies is the fact that the oil must be displaced from the reservoir rock by some other fluid, either gas or water, and this understanding yields the terms descriptive of the major reservoir production mechanisms, gas expansion and water drive' Three recent papers1-2-3 make clear the economic and conservation preeminence of Water drive as a production mechanism; in fact, the title of the latest of these is " Production under Effective Water Drive as a Standard for Conservation Practice." There appears to be an assumption at times among analysts that the effectiveness of a water drive is solely dependent on the rate of oil production; that is, if water drive appears to be insufficient or lacking, a lower oil-recovery rate would increase or reveal it. This assumption might result from the fact that the analysis has been wholly developed during the period of production curtailment; that is, since 1929. The writer takes it that the recurrent phrase in De Golyer's paper,3 "some degree of water drive," is related to this assumption. In California, an extraordinary phrase, "inactive water drive," is rather common and the connotation of uncertainty regarding our knowledge of reservoir performance is evident. Wyckoff2 speaks of the type of reservoir and performance as follows: "In general, reservoirs may be any one or a combination of domal, faulted, lenticular, or stratigraphic traps. Insofar as the dynamic performance of such reservoirs is concerned, the particular type merely determines whether regional flow is symmetrical as in a uniformly developed domal or lenticular type, or one-sided as in many stratigraphic or faulted traps." But whether the flow is

Jan 1, 1943

By Charles A. Anderson

The Bagdad copper deposit is of the disseminated type (porphyry copper) occurring in a quartz monzonite stock of late Cretaceous or early Tertiary age. This stock, located essentially at the intersection of two dike swarms, is the only one of several stocks cropping out in the area which is appreciably fractured and mineralized. Most of the rocks in the area are of pre-Cambrian age, but their structures have had no discernible influence on the copper mineralization. Hypogene alteration of the quartz monzonite includes the addition of quartz, orthoclase, and sericite and recrystalli-zation of biotite. The hypogene sulphides are pyrite, chalcopyrite, and molybdenite, the latter younger than the chalcopyrite. The late Cretaceous or early Tertiary igneous rocks, veins, and faults were controlled by northeast and northwest shear zones, the intersection of which marks the zone of appreciable copper mineralization. The minor mineralized fractures carrying the bulk of the copper have a preferred orientation parallel to the intersecting shears, and it is concluded that they are of tectonic origin rather than the result of shrinkage on cooling, crystallization, or mineralization. Supergene enrichment during late Tertiary or early Pleistocene time formed a chalcocite zone providing the minable copper ore. The enrichment was controlled in large part by northeast and northwest faults, prticularly at their intersection or where the faults are closely spaced. Introduction A major objective in a regional geologic study of a mining district is to determine whether any structural pattern can be found that has a bearing on the control of mineralization. The Bagdad copper deposit is of the disseminated type (porphyry copper) occurring in a.quartz monzonite stock which is located essentially at the intersection of two dike swarms (Fig 2). Of several quartz monzonite stocks in the area only this One is appreciably fractured and mineralized. The origin of the minute mineralized fractures in disseminated copper deposits has long been a challenging problem to the mining geologist, and evidence has been obtained to suggest that the mineralized fractures at Bagdad are related to a regional pattern of conjugate shears which also controlled the location of the dike swarms. The purpose of this paper is to Present this evidence and to emphasize the structural control of the supergene enrichment in forming a chalcocite zone that has provided the ore for the Bagdad mine. The field work on which these conclusions are based was done between October 1943 and August 1945, as a part of the copper investigations of the Goelogical Survey, U. S. Department of the Interior. The writer and his associates, E. A. Scholz and J. D. Strobell, Jr., have prepared a comprehensive report on the geology and ore deposits of the Bagdad area which will be published subsequently by the Geological Survey. Bagdad is located in west-central Arizona in Yavapai County. Ransome' divided the State of Arizona into three provinces: I? the plateau to the northeast; 111, the desert region to the southwest and 11, the moun-

Jan 1, 1949

By J. B. Pullen

THE United Verde mine is in the north central part of Arizona, on the northeasterly slope of the Black Hills, near the town of Jerome. Ore was first discovered in the district about 1875, and the first mining claims were located by M. A. Ruffner and associates in 1877. In 1888 the late Senator William A. Clark secured control of the property and under his ownership it developed into one of the country's most important copper producers. The property was sold to the Phelps Dodge Corporation in 1935, and since then has been under this Corporation's management. Except for shutdowns caused by general world-market conditions, production has been continuous from 189o to date. GEOLOGY The mineralized zone ranges in area from approximately 12 acres to less than 5 acres. All mineralization occurs in the pre-Cambrian intrusives. The first intrusion, according to geologic records, was the quartz porphyry, which later was intruded by augite diorite. Following the diorite intrusion through a series of intrusions of lesser magnitude, a pipelike mass of massive sulphide, quartz and rock was formed. The diorite forms the hanging wall of this mass, and the porphyry the footwall. Between the footwall and the sulphide a band of chlorite schist was formed, probably owing to metamorphic conditions. Commercial ore occurs along the contact of the schist and sulphide extending into the sulphide, sometimes entirely through the schist, and fingering out into the porphyry. The ore deposit was formed by replacement similar to deposits formed in limestone areas. Faulting and deformation occurred in pre-Cambrian times and again in the Tertiary period, removing approximately 2000 ft. from the top of the main United Verde ore body, forming the United Verde Extension ore body, the only other major ore body in the district. Major development work has shown that the sulphide mass extends to the 3300-ft. level, and diamond drilling below this level has indicated that the mass might extend below the 3700-ft. level, but in a diminished quantity. While many copper minerals exist in the mine, the chief commercial mineral is chalcopyrite. A plan and vertical section of the mineralized zone showing the principal geological features is shown in Figs. I and 2. GENERAL DESCRIPTION AND PHYSICAL CONDITION OF MINE After over 50 years of active production, ore still exists on almost every level of the mine. This condition is due to many causes -mine fires, which broke out as early as 1894, caused the abandonment of certain areas; subsidence and ground movements retarded the cleaning up of others. Furthermore, in the early days there was such an abundance of ore that when mining became difficult it was a simple matter to replace the production by going to a deeper level. Several attempts were made to recover the ore in the fire zone, both by glory-holing

Jan 1, 1941

By J. B. Hess, R. L. Dietrich

In the mechanical twinning of magnesium on the {1012} planes the crystal-lographic deformation is such that, in the direction of the hexagonal axis [0001], twinning is possible only undef tension stress, while in the directions perpendicular to the hexagonal axis, twinning is possible only under applied compression. Thus in extruded magnesium and magnesium alloys where the extruded textures are best described as either [1010] or [1120] fibers,' the basal planes are all nearly parallel to the extrusion axis and such material is susceptible to ( 1or2 ) twinning by compression in the direction of the extrusion axis. In order to explain the results of cyclic stressing in alternate tension and compression upon the tangent elastic modulus in such material, Dorn and Thomsen2 have postulated that, following twinning under applied compression, a retwinning or un-twinning occurs as a result of residual microtensile stresses immediately upon removal of the applied compressive force. Recently, Carapella and Shaw4 have used this supposition of untwinning in magnesium in discussing their results on indentation hardness and on cold drawing of MI sheet. In trying to confirm this hypothesis by suitable direct experiments, the authors have been unsuccessful in detecting any evidence whatsoever that untwinning follows the release of applied compression and are forced to conclude that this hypothesis is improbable or, at least, that the quantity of material involved is small. For the experiments, small cylindrical specimens 0.040-in. diam. X 0.120- to 0.140-in. long were etched from 0.0625-in. extruded rod. The ends of the specimens were accurately faced off parallel in a jeweler's lathe. The compression jig was simply an ordinary set of micrometer calipers with an anvil interposed between the spindle and the specimen. The anvil was free to move axially but restrained from rotating so that the rotation of the spindle would not introduce a twisting stress on the specimen. With this arrangement the compressive strains could be estimated to 0.0001 in. and X ray pinhole photographs could be taken with or without load as required. Fig I is the pattern of an uncompressed specimen of AZ3I alloy, showing the approximate [1010] extrusion fiber. The X ray beam is normal to the extrusion axis; in this position it is particularly sensitive in detecting twinning if one directs his attention to the diffraction ring from the basal plane. Since twinning on (1072 planes produced an 86" reorientation of the crystal lattice, the original basal reflections occur at the 3 and 9 o'clock positions while the (0002) reflections from any twinned material will occur at the 6 and 12 o'clock positions. Fig 2 shows the same specimen compressed 3.0 pct, photographed while still under load. This strain has been just enough to produce a detectible amount of twinning and the sensitivity is roughly indicated by the fact that no alterations were produced in the intensities or maxima of the other diffraction rings. A strain of

Jan 1, 1949

By J. B. Pullen

THE United Verde mine is in the north central part of Arizona, on the. north-easterly slope of the Black Hills, near the town of Jerome. Ore was first discovered in the district about 1875, and the first mining claims were located by M. A. Ruffner and associates in 1877. In 1888 the late Senator William A. Clark secured control of the property and under his ownership it developed into one of the country's most important copper producers. The property was sold to the Phelps Dodge Corporation in 1935, and since then has been under this Corporation's management. Except for shutdowns caused by general world-market conditions, production has been continuous from 189o to date. GEOLOGY The mineralized zone ranges in area from approximately 12 acres to less than 5 acres. All mineralization occurs in the pre-Cambrian intrusives. The first intrusion, according to geologic records, was the quartz porphyry, which later was intruded by augite diorite. Following the diorite intrusion through a series of intrusions of lesser magnitude, a pipelike mass of massive sulphide, quartz and rock was formed. The diorite forms the hanging wall of this mass, and the porphyry the footwall. Between the footwall and the sulphide a band of chlorite schist was formed, probably owing to metamorphic conditions. Commercial ore occurs along the contact of the schist and sulphide extending into the sulphide, sometimes entirely through the schist, and fingering out into the porphyry. The ore deposit was formed by replacement similar to deposits formed in limestone areas. Faulting and deformation occurred in pre-Cambrian times and again in the Tertiary period, removing approximately 2000 ft. from the top of the main United Verde ore body, forming the United Verde Extension ore body, the only other major ore body in the district. Major development work has shown that the sulphide mass extends to the 3300-ft. level, and diamond drilling below this level has indicated that the mass might extend below the 3700-ft. level, but in a diminished quantity. While many copper minerals exist in the mine, the chief commercial mineral is chalcopyrite. A plan and vertical section of the mineralized zone showing the principal geological features is shown in Figs. I and 2. GENERAL DESCRIPTION AND PHYSICAL CONDITION OF MINE After over 50 years of active production, ore still exists on almost every level of the mine. This condition is due to many causes -mine fires, which broke out as early as 1894, caused the abandonment of certain areas; subsidence and ground movements retarded the cleaning up of others. Furthermore, in the early days there was such an abundance of ore that when mining became difficult it was a simple matter to replace the production by going to a deeper level. Several attempts were made to recover the ore in the fire zone, both by glory-holing

Jan 1, 1941

By G. R. Rubly, H. J. Steele

The San Manuel property is in town&ips 8S and 9S, range 16E, Gila and salt River Base and Meridan, State of Arizona. This area is in the Old Hat mining district, southern pinal county, and is about 31/25 miles southwest of the town of Mammoth on the San Pedro River And one mile south of the Mammoth mine at Tiger, Arizona, The property consists of over 150 contiguous lode claims. The old Hat district was prospected prior to the civil war, but there was little or no production until 1881.1 The chief producers have been the Mammoth and Mohawk mines, now consolidated and operating as the st. Anthony Mining and Development Co., Ltd. Production to 1936 was $5,200,000, of which 83 pet was gold.2 Since 1940 the production has been chiefly lead and zinc, and some molybdenum and vanadium. There are a few small properties in the vicinity that have produced very minor tonnages of copper ore. In the San Manuel group there are claims which have been held continuously from 1906 to the present time, and at least two churn-drill holes were put down on or near the outcrop in 1917. No logs for these holes are available, but it is assumed that the grade of copper encountered was not sufficient to encourage further exploration. A small amount of ore has been shipped from open cuts on the San Manuel outcrop area, but there is no record of the tonnage Or grade. It is estimated that not more than 50 tons were mined. These cuts, plus a few shallow shafts and some short adits indicate limited and unenthusiastic prospecting at San Manuel. In 1942, through the efforts of James M. Douglas, R. B. Giffin, Victor Erickson, and Henry W. Nichols, owners of the Sari Manuel group, the Reconstruction Finance Corporation and War Production Board authorized the United States Geological Survey to investigate the property, and by their recommendation, the United States Bureau of Mines was authorized to put down a limited number of churn-drill holes. The Bureau of Mines carried On drilling from November 1943 to February 1945 Seventeen holes were drilled, varying from 305 to 1990 ft in depth. The property was brought to the attention of Magma Copper Co. in June 1944, and an option agreement was made with the Owners. Subsequently, a group of claims lying north of the original group and held by the Apex Lead Vanadium Mining Corp, and a group to the east held by the Quarelli family, were optioned. A drilling program was laid out to conform to the Bureau of Mines pattern, and drilling started in December 1944 Sari Manue1 Copper Corp. was incorporated September 1945, and has carried on the exploration program to the present time. Geology General The mineralized outcrop, chief copper mineral of which is chrysocolla, is a tri-

Jan 1, 1949

By B. Blumenthal

THE present investigation was planned as a survey of the lead-rich portion of the ternary lead-antimony-silver system by thermal analysis. Since, however, a rigorous application of the conventional thermal analytical method is time consuming, an attempt was made to speed up the investigation by reducing the time required for a single thermal analysis. This was done by increasing the rate of cooling to 12° to 18°C. per minute, since such a rate does not permit even an approach to equilibrium conditions, the melt was stirred vigorously by a stirrer operating at the high rate of 665 r.p.m. This proved to be effective in obtaining cooling curves with distinct points of arrest and of excellent reproducibility, which satisfactorily compare with those obtained at a rate of 1" to 2°C. per min. with or without slow stirring (Fig. I). By this method the lead-rich end of the lead-alltimony system and a series of ternary alloys in sections parallel to the lead-antimony side of the ternary system were investigated and it was observed that the two branches of the liquidus curve of the binary alloys did not intersect at the euteotic temperature. An equivalent effect mas observed in the ternary system. The eutectic temperature of the binary lead-antimony system was found to be 252.0°C., which confirms the recent in- vestigation by Pellini and Rhines,1 who determined the eutectic temperature to be 2 51.5°C. The observation that the curves of primarY crystallization of the lead-antimony system do not intersect at the eutectic temperature was previously made by Dean.2 Dean explains the phenomeilon by assuming the existence of a compound Sb4pb. He felt that supercooling was not the cause of the phenomena because he was unable to influence them by inoculation. The X-ray investigation by Solomon and Morris-Jones,3 the metallographic investigations by Stead,4 Charpy,5 Gontermann,6 and Dean, Zickrick and Nix,7 and the numerous investigations of physical properties, definitely disprove the occurrence of any compound. The work of Dean was not confirmed by Broniewski and Sliwoski,8 whose experiments did not show any irregularity and who report a eutectic composition of 13 per cent antimony and a eutectic temperature Of 2500 to 252°C. at a rate Of coo1ing of about 6°C. Per min. Abell Redlich and Adler9 then report a eutectic composition of 12.1 per cent upon reviewing the previous publications and adding a few of their own cooling curves. In 1934 Quadrat and Jiriste10 found from careful analyses of the bottom portion of slowly cooled hypereutectic melts that the eutectic only 11 .4 to 11.5 per cent antimany. (Previous analyses by Stead4 .in 1891 gave 13 per cent.) Weaver,ll however, reported in 1935 that cooling cunres indi-

Jan 1, 1944

By Ernest L. Ohle

The newly opened Hayden Creek lead mine represents a variation from the usual Southeast Missouri type. Galena mineralization occurs in sandy dolomite cementing a conglomerate of granite boulders and in cracks in the boulders. The conglomerate occurs at the base of the Bonneterre formation on the slopes of two buried pre-Cambrian knobs. IN 1943 diamond drilling from the surface in an area 2 miles southwest of Leadwood, Mo., discovered a lead deposit of a markedly different character from the usual southeast Missouri type. Subsequent drilling of about 500 holes indicated several million tons of ore, and in 1950 a 701-ft vertical shaft was sunk into the orebody. This paper describes the geology of this interesting occurrence insofar as it is known from the drilling and the small underground exposure at the bottom of the shaft. Geology The location of the Southeast Missouri Lead Belt and of the Hayden Creek property are shown in Fig. 1. As shown here, there are two separate producing areas, one from which the larger tonnage has come, located near Bonne Terre, Flat River, Desloge, and Leadwood, and the other to the south around Fred-ericktown and including famous old Mine LaMotte. The best published description of Lead Belt geology is by Tarr.* In pre-Cambrian time in this area, an assemblage of granites and rhyolitic flow rocks was eroded to a mature topography. Sedimentation, beginning in the Upper Cambrian, filled in the valleys and gradually covered even the highest hills. The first formation deposited was the La-motte sandstone; it is successively overlain by the Bonneterre dolomite, the principal lead-prodbcing formation, then the Davis shale. the Derby-Doerun limestone, and a succession of Cambro-Ordovician cherty dolomites. Several of these formations may be found in direct contact with the pre-Cambrian as their deposition progressively overlapped the older rocks on the flanks of the igneous knobs and ridges. Immediately overlying the pre-Cambrian there is, not uncommonly, a thin basal conglomerate of granite or porphyry boulders, which is incorporated into the overlying sediments. Deposition of the lower part of the rock section was fairly continuous, and the Lamotte sometimes grades almost imperceptibly into the lower sandy Bonneterre. Since the sediments were deposited on an uneven floor, they tend to reflect the irregularities in that floor. Most of the steep dips found in the district, that is, dips in excess of 10°, are original dips and not caused by deformation. Such domelike structures in the sedimentary rocks around the igneous knobs have localized a considerable number of the orebodies in the district and particularly those in the Frederick-town area. Many of the larger orebodies, however, have no close relation to the pre-Cambrian topography. Most of the lead production has come from the lower 150 ft of the Bonneterre formation, where disseminated ore spreads laterally parallel to the bedding for great distances. Average stoping height is about 20 ft, but in a few places there are stopes over 175 ft high.

Jan 1, 1953

By Ralph E. Esarey, Robert G. Reno

DriLLing activity and prospecting for oil and gas increascd in Indiana in 1941 over the previous year. The greater part of the drilling and development continued to centralize in the Indiana portion of the Interior Coal Basin, in the southwestern part of the state, but other parts of the state were not neglected. Many wildcat wells were drilled, including a series of core tests through the mantle of drift on the southern flank of the Michigan Basin. These core tests have been followed by several unsuccessful production tests. Production tests were made also along the axis of the Logansport-Kankakec branch of the Cincinnati Arch. In all, 411 field locations and 141 wildcat wells were completed in Indiana during 1941; that is, a total of 552 wells, an increase of 3 2 wells over the previous year. The field tests resulted in 260 oil wells, 57 gas wells, and 94 dry holes; wildcats included 16 oil wells, 3 gas wells and 122 dry holes. At the end of the year, 53 field wells and 34 wildcats were drilling. Gibson and Posey Counties led the state, with 154 and 155 wells drilled, respectively. However, 125 wells produced oil in Gibson County, while 98 produced oil in Posey County. Twenty-five per cent of all wells drilled were wildcat; II per cent of these produced oil and 5 per cent produced gas. Grifin field continued to lead in drilling activity, with 157 successful wells and 20 dry holes (including important wells defining the field). Production is found in five pay zones (Tar Springs, Waltersburg, Elwren, Aux Vases and McClosky). It produced a major part of Indiana's estimated 7,200,000 bbl. of oil during the year. Heusler field, Posey County, expanded with 11 oil ells and 4 dry holes in the Waltersburg and Tar Springs. Vienna field, Posey County, completed four oil producers in the Mansfield sandstone, between 1200 and 1250 ft. The College field, discovered late in 1940, received three oil producers and two dry holes in the Aux Vases. Two new fields were discovered in Posey County during the year: Lamott pool, in the Tar Springs, at 1950 ft., had initial production of 55 bbl. on discovery. One producer and one dry hole have been drilled since. Mt. Vernon pool found saturation in both the Waltersburg and Cypress formations. The discovery well tested about 1000 bbl. per day; it tested the McClosky at 2764 ft. Seven producers have been drilled since the October discovery. Welborne-Switch pool found oil in the Cypress sand at approximately 2500 ft., with an initial production of 33 bbl. One more well in the area proved a dry hole. Gibson County had the following discoveries in 1941: The Patoka field was opened by a McClosky producer of 300 bbl. Another producing well has been drilled. An attempt was made to extend the Illinois Mt. Carmel field into Gibson County, Ind., and one producer of 24 bbl, was completed on the Indiana side. A dry hole has since been drilled, one location south. One small well was completed in the Mans. field at 1105 ft. in sec. 31, T.2 S., R.12 W., Gibson County promising a new field

Jan 1, 1942

The papers discussed in the following pages were presented during two sessions of the Geophysics Education Committee of the Mineral Industry Education Division on Feb. 17 and 18, 1941. At the first meeting, to consider the "Influence of Geophysics upon Geology Curricula," this Committee was joined by the Geophysics and Mining Geology Committees of the A.I.M.E., the Society of Economic Geologists, representatives of the American Geophysical Union, and delegates from the Committees on College Curricula and on Applications of Geology of the American Association of Petroleum Geologists. Quentin D. Singewald and Sherwin F. Kelly presided. At the ensuing session, especially emphasizing the integration of geology, physics and chemistry for the solution of earth problems, the joint participants with the Geophysics Education Committee were the Geophysics Committee, and representatives of the American Geophysical Union and of the Committee on College Curricula of the American Association of Petroleum Geologists. Richard M. Field and W. R. Chedsey presided. In the following summary of the discussion at the two meetings, written discussion submitted subsequently is not differentiated from that offered orally at the session. A provisional report of the Geophysics Education Committee was presented at the second session, and some of the following discussion refers to it. This report has not been printed (it is anticipated that a more comprehensive, final one will be rendered at the 1942 annual meeting). A few mimeographed copies of this provisional report were made. Dr. W. P. Haynes presented some notes prepared by Dr. F. H. Lahee, Chairman of the American Association of Petroleum Geologists' Committee on College Curricula. This Com- mittee's inquiries reveal the general opinion that a four-year academic preparation is inadequate, five or six being advisable. The fundamentals, mathematics, physics, chemistry, and English composition, should be stressed in the first three years, with specialization in the last two or three years. Some companies provide an apprenticeship period, and themselves give additional training. During academic years more attention needs to be given to engineering training, to field mapping, and in geology to stratigraphy and sedimentation. The amount of mere memory work should be cut, and men trained to observe and reason. Dr. Lahee emphasized the need of more adequate preparation in English composition, because of the inability of many graduates to compose acceptable reports. Sherwin F. Kelly pointed out that much time in university training, which ought to be devoted to technical subjects, was taken .up with English courses. He emphasized that it is the part of the universities to demand of the high schools that the students they send to the university be properly trained to speak and write English. Prof. W. T. Thom protested against the crowding of high-school material into already overcrowded college curricula. C. E. Dobbin, chairman of the Committee on Applications of Geology of the American Association of Petroleum Geologists, described briefly the work of his committee in publicizing geology, and said that it found a widespread popular interest in the subject but a lack of appreciation of its importance. He recommended that attempts to coordinate the works of geologists and geophysicists be expanded somewhat toward the further developing and encouraging of a "species of geopolitician" capable of assisting the progress of geology and geophysics by more vigorous advertising of

Jan 1, 1946

By R. C. Mahon

THE Homer iron-ore mine is at Iron River, Mich. Because it covers a large area, 400 acres, and because there was a considerable depth of water in the glacial drift above most of the ore bodies, this mine has presented a number of unusual and often difficult operational problems. The purpose of this paper is to discuss a few of the most important problems encountered. SURFACE WATER Mining on this property was started on one 40-acre tract. The ledge in this area was the highest on the property and, although it was a real problem, water could be handled by underground pumping. During the first period of mining, drifts were driven just under the ledge and holes were drilled through to the surface material. In later years these drifts have been extended wherever possible. Although these drifts assisted in the drainage problem, it was evident they would not be sufficient alone. Before mining on a large scale could be started on this property, the water problem had to be solved. A number of test holes were put down to the ledge, and showed that there was an average 150 ft. of water-saturated glacial drift above the ledge over the rest of the mine. The upper 70 ft. was gravel and sand and the lower 80 ft. clay and hard pan, with some narrow seams of sand and gravel. It was evident that the water above the clay seam could not be drained off through openings in the ledge and for that reason it was decided to install surface drainage wells. This method of drainage was entirely new at that time and was pioneered at the Homer mine. The sinking of the first well was started in June 1929. Immediately following the first well a number of wells were sunk, but only to the top of the clay seam. This was done with the idea that a greater capacity could be obtained in a shorter time from gravel seams where the water flowed more freely and that the cost of pumping the water above the clay seam would be considerably less than if the wells had all been sunk to the ledge at once. Before the drainage of surface water was started, 1200 gal. per min. against a head of 800 ft. was being pumped from the mine. By March of 1932, with five surface wells in operation, the mine pumping had been reduced to 150 gal. per min. At this time we were pumping 5000 gal. per min., under an average head of 110 ft. from the surface wells. The total pumping costs were 30 per cent less than in 1929 because the greater capacity was being pumped at a much lower head. From 1932 to 1936 the mine was idle and all surface pumping was stopped. Since 1936, 10 new wells have been added with a total pumping capacity of 8000 gal. per min. at the present time. The water level has been lowered 70 ft. since surface pumping was started in 1929, and it is now approximately at the top of the clay. To remove the water below the clay seam, 11 of the 15 wells were sunk to the ledge.

Jan 1, 1945