Search Documents

By H. A. Wriedt

At 500°C (932°F) the range of y' iron nitride is from 5. 77 + 0.03 wt pct N (in coexistence with a iron) to 5.88 * 0.03 wt pct N (in coexistence with E iron nitride). Stoichiometric "Fe,N" (5.900 wt pct N) is near the upper extreme of possible compositiom. The depe-dence of nitrogen activity (expressed as pnh,/Ph,) on nitrogen content is described satisfactorily by a "Langmuir" isotherm: At even the highest nitrogen concentrations, less than 0.18 pct of' the nitrogen atoms present are impositions of disorder. Past investigations1-4 of the Fe-N system have left only details of the thermodynamic behavior of the y' nitride, "Fe,N9', to be studied. The present investigation was made to establish more precisely than hitherto the limits of composition and the relation between composition and nitrogen activity at 500°C. EXPERIMENTAL TECHNIQUE The compositions of nitrides in equilibrium with various NH, + Hz mixtures at 500°C were determined from the weights gained by 0.02-in.-thick (4.0 to 4.5 g) strips of purified iron* when the nitrides were formed A description of the gas generation and furnace system has been published.5 Cracking and blistering during conversion of the original solid iron at 550°C injected considerable porosity into the strips without causing their disintegration. The time for complete conversion was significantly lowered by periodically reducing partly nitrided specimens in hydrogen and then reexposing them to the nitriding gas. Gas mixtures producing single-phase were used in the equilibrations at 500°C. Equilibrium was regarded as existing when the specimen weight was not detect-ably affected by further exposure to the same conditions. The gas compositions and nitrogen activities at which y' transformed to a iron (lower activity limit) and to E iron nitride (upper activity limit) were redetermined during the investigation. A specimen was equilibrated in an NH, + Hz mixture at 500°C and then exposed to a s1ightly different gas. When equi- librium had been reestablished the gas was again changed slightly. At each stage of this repeated process, while the specimen was reacting with the gas, the variation of its weight with time was observed. The onset of phase transition was marked by an abrupt change in the amount and rate of weight gain or loss. The specimens were weighed outside the furnace, in air and at room temperature, on a balance with 0.05 mg precision. When it was found that the specimens were oxidizing at a significant rate during the weighing, a series of timed weighings was made with each specimen, starting 1 min after its exposure to air. RESULTS AND ANALYSIS The gain in specimen weight from oxidation during weighing was linear in the logarithm of time between 1 min and about 2 hr, Fig. 1, later becoming linear in the cube root of time. In the logarithmic period, nitride specimens oxidized two to three times as fast as

Jan 1, 1970

By James H. Courtright, Kenyon Richard

L. H. Hart (Chief Geologist, American Smelting & Refining Co.)— Because of a widely recognized association between breccia pipes of one form or another and many important copper deposits, conditions under which breccia pipes develop have been of great scientific interest for many years. Since these phenomena first attracted attention, many theories have been advanced to explain their origin. This is not unexpected, since it is likely that they have been formed by and under a wide range of conditions. Moreover, the entire subject is confused by the fact that the term brec-cia pipe is applied to a wide variety of occurrences. To discuss any part of the subject intelligently, therefore, it is necessary to start with definitions of the terms used. In their discussion of the Toquepala deposit, Richard and Courtright have carefully defined the terms they have used in their presentation of a very logical geological history of Toquepala breccias. This is a real contribution, as there is no reference in the literature known to the writer where the history of a series of breccia pipe epochs, confined essentially within one channelway, may be read with the degree of certainty that appears to be possible at Toquepala. Although the following comments are intended primarily to emphasize points brought out in the article by Richard and Courtright, certan subsequent detailed mapping by Hollister and Houston7 within the main central mineralized area of the Toquepala deposits not only supports most of Richard's and Courtright's con- clusions but also contributes additional facts that strengthen and broaden the whole concept of the origin of the Toquepala breccia pipes. In detailed mapping by Hollister and Houston,' the most significant feature disclosed is a well developed system of concentric fracturing in rocks peripheral to the main breccia pipe throughout an arc of 300°, interrupted only by the late dacite agglomerate in the north quadrant. Although Richard and Courtright noted that such fractures were developed in the southern and southeastern areas, continuity in the east and west quadrants is established by consistent orientation of the stronger set of fractures and joints. The existence of these structural weakness trends is emphasized by the emplacement of dike-like phenomena in and along members of this fracture system. Richard and Courtright described one of these dikes in the southeast quadrant. They referred to it as a ring-dike, composed of dacite porphyry. This suggests an apparent structural control of at least a part of the dacite porphyry intrusion by features related to the Toquepala breccia pipe center. This raises a perplexing question, since the dacite porphyry intrusion had been presumed to antedate breccia pipe activity. However, if this ring-dike is related to the breccia pipe center, it may indicate that some part of the dacite porphyry intrusion advanced in a manner resulting in an intensely localized stress center, which produced the concentrically arranged fracture system. The ring-dike would then appear to be evidence strongly sug-

Jan 1, 1959

By J. H. Carpenter

LMENITE, rutile, zircon, and other heavy minerals are found in small amounts in the sand that covers most of Florida. Small enriched deposits occur on the beaches and coastal dunes. One beach deposit east of Jacksonville was worked during World War I and another near Vero Beach during World War 11. Both ceased operation when the resumption of imports reduced prices. Early in World War II reduction of rutile imports made a domestic source of the mineral necessary to maintain the expansion of armaments. Explorations made near Jacksonville discovered a relatively large body of low-grade ore about 10 miles inland from the beaches. A plant installed by Rutile Mining Co. of Florida using both flotation and tables encountered difficulties because of low plant capacity and organic slimes in the ore. In 1944 Humphreys Gold Corp. solved the problem of concentrating the low-grade ore by using the newly developed Humphreys spiral concentrator and by mining with a hydraulic dredge. This combination of low cost mining and concentration permitted the plant to continue operation in competition with foreign ores when imports were resumed following the war. The success of the Jacksonville operation renewed interest in Florida as a source of titanium. An extensive survey of the state was made by E. I. du Pont de Nemours and Co., Inc., under the direction of J. L. Gillson in 1945 to 1946. Sampling was carried on by drive pipe drilling to depths of 20 to 25 ft. Encouraging values were discovered near the location of the present Trail Ridge mine, 50 miles southwest of Jacksonville, near the town of Starke. The United States Bureau of Mines was interested in exploring for heavy minerals in Florida, and on the recommendation of both the state geologist of Florida and of Du Pont geologists, drilled deeper where marginal indications were found on Trail Ridge. In 1947 it was discovered that sufficiently higher values occurred at depth to make the deposit commercial. The orebody at Trail Ridge is a long sand deposit averaging about 1 mile in width and 35 ft in depth. It is approximately 1 1/2 miles wide at the north end of the portion now being worked, tapering to a blunt point 3 miles to the south. The ore reaches a maximum depth of 65 ft near the center and feathers out into barren sand at the edges. The ground surface is relatively flat and is covered with vegetation including pine, scrub oak, palmetto, and occasionally in swampy areas, cypress. The remain of a dense woody growth underlies and marks the bottom of the Ore 'One. It is difficult to drill through this layer, but in some cases where it is less than 5 ft thick it has been possible to drive through the wood. Sand lying below is coarser than that in the ore zone and contains no values. The wood layer consists of unconsolidated carbonized fragments of branches and other forest trash associated with a considerable amount of ar-

Jan 1, 1954

By R. Taggart, D. H. Polonis, J. C. McMillan

Thin foil electron microscopy techniques have been used to study the micros tructure of a Ti- 7.5 wt pct vanadium alloy in the quenched and aged cond_itions. Selected area diffraction has identified a (1011) twinning mode accompanying the martens ite t9.an.sfo?rn~ation. Precipitation of the 0 phase during the aging of quenched alloys has been obsevced to occuv in the form of plates and needles with preferential growth along the (1120) direction in the a' matrix. In the present work, the micro structures of quenched and aged alloys of the 0 isomorphous Ti-V system have been investigated by means of thin-foil electron-microscopy techniques. Most of the previous studies of martensitic phases in titanium-base alloys have utilized optical microscopy and X-ray diffraction techniques. The application of transmission electron microscopy is more recent, and only a few such studies have been reported.1-5 This paper is concerned particularly with the crystallographic nature of substructures formed in the martensitic a' plates. The early stages of aging or tempering have also been examined to determine the modes of precipitation from the martensitic solid solutions. Such information is essential in studying strengthening mechanisms and in determining the feasibility of high-strength rnartensitic alloys based on titanium. Liu and Margolin6 reported several types of substructures within the martensitic plates of quenched Ti-Mn alloys. It was later suggested by Liu7 that the structure of martensitic plates might be very complex and not single crystals as normally assumed. The sub-markings could not be identified with the two possible habit-plane orientations {334}ß and {344}ß, and it was not positively determined whether they are associated with mechanical twinning. The recent studies by Armitage5 on titanium martensites in a variety of commercial alloys have indicated that twinning does not generally accompany the transformation. This observation is in accordance with the Mackenzie and Bowles model for the transformation in pure titanium8 which suggests that twinning is not to be expected. However, a number of other recent investigators have reported twinlike substructures in the martensitic plates of several titanium systems including commercia1 titanium,2,3 Ti-Cu,5,9 Ti-Ta,1 and the commercial alloy Ti-8A1-1Mo-1V. Blackburn* has reported that the structure of quenched Ti-8A1-1Mo-1V depends on the prior solution temperature. He identified two types of martensitic structures, one of which is described as a heavily faulted hcp or twinned fcc structure and the other an hcp structure with a high internal dislocation density. The latter type exhibited some twinning with a (1011) twin plane. EXPERIMENTAL PROCEDURES AND RESULTS The alloy used in the present work was a 7.5 wt pct V alloy that was prepared by conventional arc-melting techniques. This alloy composition was selected

Jan 1, 1968

By Huey-Lin Luo, T. R. Anantharaman, William Klement

Two new metastable phases have been obtained in Au-Ge alloys by rapid cooling from the melt. One is of the hep structure with near-ideal axial ratio and may be considered a Hume-Rothery phase. The other has a complex tetragonal structure (a = 11.627Å and c = 22.191Å for the Au60Ge40 alloy) and may be looked upon as a superlattice made up of forty-four fee unit cells. Alloys with the tetragonal phase are charactevized by marked preferred orientation. The metastable constitution of the Au-Ge alloys is discussed with reference to the rate of cooling from the melt. THE Au-Ge equilibrium diagram features a rather deep eutectic near 27 at. pet Ge with a maximum solid solubility of 3.2 at. pet Ge in gold and is similar to the Ag-Ge, Ag-Si, and Au-Si diagrams.' The present study of the effects of rapid cooling from the melt on the structure of Au-Ge alloys constitutes an extension of similar investigations2-8 in this laboratory on alloys of noble metals with germanium and silicon. Nonequilibrium hep structures have so far been obtained by quenching Ag-Ge2, 3 and Ag-Si4, 5 alloys from the melt; an Au-Si alloy of approximately eutectic composition has been found6 to solidify in a noncrystalline state. EXPERIMENTAL PROCEDURES Twenty-nine alloys prepared from gold of 99.9+ pet and germaium of 99.999 + pet purity were investigated. The method of alloy preparation, the technique of rapid quenching from the melt, and the X-ray diffraction procedures were similar to those described previously.3, 4 Essentially, small sections (-20 mg) of thin alloy rods (-1 mm diam) were rapidly heated up to 1200°C in a graphite crucible under argon and the liquid alloy ejected by a helium blast onto a polished copper strip held on the inner periphery of a rotating wheel. The resulting thin foils were examined with or without the copper substrate in a G.E. X-ray Diffractometer or in a 114.6-cm-diam Debye-Scherrer camera. RESULTS Table I gives the constitution of liquid-quenched Au-Ge alloys, as estimated from intensities of X-ray reflections from the corresponding phases, viz., a (fee solid solution), ß (hep phase), ? (tetragonal phase), and diamond-cubic (dc) germanium. Despite unavoidable variations in the quenching rates, the proportions of the phases in different alloys were generally reproducible and stable at room temperature. There was no evidence of quenching strain, since the a doublets were well-resolved in high-angle Debye-Scherrer reflections in all cases except where stacking faults in the a fee and ß hep structures contributed to X-ray line broadening. The ß and ? metastable phases showed signs of decomposition to the equilibrium a phase and germanium only after a few hours annealing above 100°C. A few alloys around the eutectic composi-

Jan 1, 1965

By Jack White, Ralph B. Adair

The Mufulira mine in Northern Rhodesia is 13° south of the Equator and at an altitude of 4100 ft above sea level. The concentrator was planned in 1930 to treat about 10,000 tons of ore per day, but before construction work had gone very far the size of the plant was reduced to 1500 tons daily capacity. Then just as the construction was finished in December 1931, the price of copper did not warrant the commencement of operations and it was not until October 1933 that the mine re-opened. Extensions have been made to the plant in 1934, 1935, 1936, 1937, 1940 and finally in 1945. The capacity of the plant when the 1945 extension is completed will be 9500 short tons per day. The various extensions have been carried out with the minimum confusion and with great skill on the part of the designers and the erection engineers. In dealing with the plant in this paper it is proposed to give an outline of the present practice and only to refer to past practice when it is considered of particular interest. Ore Treated The ore consists of fine grained highly siliceous, felspathic and argillaceous quartz- ites, the latter containing graphitic carbon and locally termed graywacke. These rocks are considerably altered near the surface and on the fringes of the ore body. Despite extensive efforts at mixing, both underground and in the crushing plant, many sudden changes of ore take place in the mill feed. The minerals are chalcocite, bornite and chalcopyrite with relatively unimportant amounts of malachite, native copper, azurite, covellite and chrysocolla. Gold is present at about I oz to a thousand tons, and silver at about 2 dwt. per ton. With increasing depth the nonsulphide content or,, as commonly termed locally, the oxide content of the ore is decreasing and is now less than 0.25 pct against a high of 0.77 pct- Crushing Operations The first stage of crushing is done under. ground where the oversize from I2-in. grizzlies is fed to a 56 X 72-in. jaw crusher. At the Selkirk shaft two 10-ton skips deliver the run of mine ore at a rate of 450 tons per hour to the 400-ton capacity shaft bins. One 6 ft wide Ross chain feeder and one locally made air-operated finger feeder feed the two 30-in. McCully crushers. Ahead of each crusher is a 6 X 9-ft spring grizzley spaced at 5 in. on a 35O slope. Neither the Ross chain feeder nor the finger feeder is entirely satisfactory and for the wet, muddy and sticky ore that has to be handled it is planned to replace these with two 6-ft wide apron pan feeders. The McCully crushers deliver a minus 5-in. product, at a.rate of over 500 tons per

Jan 1, 1949

By Cyril Stanley Smith

On the 6th of February 1684, Dr. Martin Lister mentioned at a meeting of the Royal Society1 that "brass is magnetical," and promised to give an account of that assertion at some other time. He repeated his promise but never fulfilled it, and it was left for William Arderon2 to show, in 1758, that brass could be made magnetic by hammering and that it would retain polarity after magnetizing. Twenty-seven years later Caval103,4 examined the matter in great detail. Working with cast calamine brass, he showed that it could be made magnetic by hammering and nonmagnetic by subsequent annealing at a red heat. He found that annealing at a very high temperature caused the samples to lose their magnetic quality permanently, even after subsequent cold-working, but that remelting and cold- working restored it. He encountered some samples of brass that could not be rendered - magnetic by any treatment. Experiments in which these were remelted with iron additions gave negative results, and Cavallo concluded that iron impurity was not the cause of the magnetism. He worked with 50-grain (3-gram) samples melted under the blowpipe, hence cooled very quickly. Bennet5 made whole crucible charges from copper and zinc, and found _ the resulting brass ingots to be magnetic only when iron had been added and then only after cold-working. All these observations applied to material in the cast condi- tion, in which coring would produce a continuous spectrum of composition and cooling would result in varying degrees of precipitation. This knowledge of the subject seems to have been forgotten in the nineteenth century. The older brass was made by the calamine process and frequently contained iron in amounts of 0.5 per cent or more, absorbed from the impure ore with which the copper and charcoal were heated in making the brass. When metallic zinc became available in commercial quantities, calamine brass gradually disappeared, and with it the knowledge of its curious magnetic properties. Only when sensitive apparatus replaced the compass needle of the earlier investigators could the effects be detected in relatively pure metal. The effect of cold-working in inducing ferromagnetism was rediscovered by Bitter8 in 1930 in a sample of impure copper, and this was confirmed by Lowance and Constant: Honda and Shimizu, l0,11 and others. In the same year, Tammann and Oelsen12 showed that copper-rich copper-iron alloys after certain heat-treatments could be rendered ferromagnetic or made more strongly ferromagnetic by cold-rolling. Kussman and Seeman13 showed that the change of susceptibility of relatively pure copper on cold-working was associated with the iron content, and concluded that actual precipitation of iron was caused by cold-working, which is a satisfactory theory until one considers the improbably high rate of diffusion that this would involve. When studying precipitation phenomena in

Jan 1, 1942

By G. S. Hume

During the war years the drilling activity in Canada has been steadily increasing and still further increase is expected in 1945. The production of oil, which in the past has come largely from the Turner Valley field in Alberta, shows a decline since 1942, the peak year. New discoveries made in 1944, however, give promise of replacing the decrease from Turner Valley where the crude-oil production in 1944 was nearly 1,800,000 bbl. less than in 1942, but with an increase of 145,000 bbl. in natural gasoline, a product of great value to the war effort. A very considerable part of the decline in Alberta has been offset by new production of more than a million barrels in 1944 from the Norman Wells field, in the Mackenzie River area of the Northwest Territories. It should not be forgotten, however, that this is largely due to the Canol development, a war project, the future of which is dependent on many factors not connected with an ordinary commercial operation. The year 1944 has been the best in new discoveries in Alberta for all time. The discovery of a new deep field at Jumping-pound, 20 miles west of Calgary, with the hopc of a type of product similar to that of Turner Valley is the culmination of many years of effort to interpret the subsurface structures in relation to the complicated surface foothills faulting and folding. In this case the subsurface structure on the Paleozoic limestone was inferred from geological investigations but precisely defined by seismograph. In addition to Jumpingpound the discovery of oil of 34.5 gravity at a depth of less than 5000 ft, in the Devonian of the Plains at Princess, 125 miles east of Calgary, is of great significance since this is the first substantial production from the Devonian in Alberta, although previously some oil had been obtained at two places from the Devonian in the foothills. The effect of this discovery is already apparent in the number of wells now drilling to the Devonian in the southern Plains. In southern Alberta a new producing area has been found in a Lower Cretaceous sand at Barnwell, a few miles west of Taber. Also, at Conrad, 20 miles southeast of Taber, an important new discovery has been made at a depth of about 3000 ft. in a sand in Jurassic shales, in a strali-graphic trap on the northeast flank of the Sweetgrass arch. In northeast Central Alberta an important extension has been found in the Lloydminster area, where only a few wells have so far been drilled. A new well 3 1/2 miles south of the previous producers found a coarser sand at the productive horizon and as a result will have an increased daily yield. At Blackfoot, 9 miles west of Lloydrninster, a new producing area in the Lower Cretaceous may have been discovered at a depth of 2004 ft. At the end of 1944 the well was being tested. Forty-four unsuccessful wildcat wells were drilled in Alberta in 1944. The decline of Turner Valley, the major producing field, was anticipated at the beginning of the war and in an effort to offset this and encourage new development the Dominion Government put into force tax concessions and other measures that,

Jan 1, 1945

By John V. Morgan

Although the Lansing-Kansas City groups One one of the more important producing horizons of Central Kansas, exploitation has been hindered by inability to consistently identify and correlate the various productive intervals. A study of gamma ray-neutron logs and core data indicates that definite zones exist which are related to production and which may be generally correlated over an appreciable portion of Central Kansas. A suggested system of zoning and nomenclature is developed and illustrated, along with examples of its specific application in overall evaluation and in development of zonal production characteristics. General adoption of the suggested system should aid appreciably in the future development of commercial Lansing-Kansas City production in Central Kansas. It is probable that similar systems might be developed for other regions where production is obtained from various uncorrelated and unnamed zones in thick pay intervals. GENERALIZED GEOLOGY OF CENTRAL KANSAS The most important large subsurface feature in Central Kansas regarding oil production is the Barton Arch, which is part of the Central Kansas uplift. The Barton Arch is a buried ridge of Pre-Cambrian granite running northwest-southeast, near which the majority of Central Kansas oil fields have been found. To the northeast of this arch, the granite dips sharply into the Salina Basin and similar basin areas to the west and south are termed the Hugoton Embayment and Anadarko Basin, respectively. This report deals Primarily with the region of the Central Kansas Uplift and its southwestern flank. Fig. 1 indicates the general location of subsurface structural features along with the oil and gas fields of central Kansas. Above basal granite lies the Cambro-Ordovician Arbuckle Dolomite which is the principal oil producing zone in Central Kansas. This formation, as well as those higher in the section, reflects the general underlying granite structure; however, the Arbuckle top is an erosional surface and most oil producing structures are probably topographic hills. Formations above the Arbuckle in ascending order may include those of the Ordovician, Silurian, Devonian, Mississippian, Pennsylvanian, and Permian periods as well as certain recent sediments. As the Barton Arch is approached, those formations below the Pennsylvanian and above the Arbuckle tend to pinch out until Pennsylvanian rocks, which include the Lansing-Kansas City groups, rest directly upon the Arbuckle. The Arbuckle itself is also completely eroded away at points on the Arch, but is up to 600 ft thick only 20 to 30 miles down dip. Formations of the Pennsylvanian system vary considerably in thickness but probably average about 1,000 ft as an overall total. The more commonly known oil productive zones are the Tarkio, Topeka, Toronto (Dodge), Lansing-Kansas City and Marmaton. Of these, the Lansing-Kansas City, which varies from about 200 ft to 400 ft in thickness, is the most important, since its areal frequency of oil production is exceeded only by that of the Arbuckle. Most Pennsylvanian rocks in Central Kansas were deposited in shallow seas which alternately covered, then retreated from the land. This resulted in recurring cycles of thin beds which cover relatively large areas. Small surface deformations during the period of deposition also caused variations in the type material deposited and its thickness. The local structures of Pennsylvanian time probahlv influenced the accumulation of

Jan 1, 1952

By P. D. Southgate

VIBRATION, both ultrasonic and sonic, can affect the course of a variety of metallurgical processes. Reports of work on this subject have appeared at intervals over the last twenty years and a thorough review has been made by Hiedemann,' who gives a full list of references. It has been established that both refinement of structure and outgassing of the melt can be produced in most metals with sufficiently intense vibration. Many of the experiments in this field have been carried out using alloys of direct commercial interest in production- type casting equipment. Here a different approach is adopted, and simple binary alloys which exhibit different types of structure are used to facilitate examination of the effects produced under well-controlled conditions. Results from this kind of experiment should enable the basis of larger scale experiments with similar types of materials to be better substantiated. The alloys selected for this work are: 1) aluminum of 99.2 pct purity, the principal impurity being iron, near 0.4 pct; 2) A1-1.8 pct Fe, which is near eutectic composition; 3) A1-4 pct Fe—the second phase, of composition FeAl3, forms distinct acicular crystals; and 4) A1-12 pct Si—although this is of eutectic composition, the silicon normally appears in the form of large plates. Experimental Method There are three practicable methods by which acoustic vibration can be transferred to liquid metals: a) vibration of the whole of the container; b) electromagnetic induction; and c) insertion of a vibrating probe into the liquid. Method c is chosen here, and a frequency of 8 kc per sec is used. The end of the probe is electrically heated so that the metal near it will be the last to solidify. This ensures that vibration is transmitted directly to the liquid metal without passing through any solidifying and pasty intermediate region, which would attenuate acoustic waves severely. In addition, the heating prevents solid metal adhering to the probe, with consequent detuning. The transducer assembly is shown in Fig. 1. A stack of Permendur laminations 30 cm long acts as a half-wave vibrator and a winding along its length carries polarizing and energizing currents. It is joined by a half-wave coupling bar to a mild steel exponential horn, which tapers from 3.8 to 1.1 cm diam. A stainless steel stub 3 cm in length is welded on the free end. The assembly is supported by a plate located at the node of the coupling bar. Acoustic radiation losses are minimized by allowing the free end of the transducer to protrude above the surface of the cooling water. The exponential horn serves the function of matching the acoustic output impedance of the transducer to the radiation resistance of the probe into the melt. Electrical drive is provided by a 1 kw generator. Measurements of probe vibration amplitude during melt treatment are obtained from a gramophone pick-up with the needle attached to the wide end of the horn. This device is calibrated with a microscope before use. Liquid aluminum is very actively erosive and solution of materials with which the molten metal comes into contactcauses difficulties. Erosion of the probes in particular can be severe since it is greatly accelerated by the vibration. Tests of various acous-

Jan 1, 1958

By Walter J. Karplus

By means of a finite difference expansion a fluid flow field in cylindrical coordinates with axial symmetry, is simulated by a network of electrical resistors. A series of DC analog computing units, connected to the network bounrlary corresponding to the free surface effectively adjust the network parameterr to satisfy simultaneously Laplace's equation and the borrndary conditions. The system automatica1ly "re1axes" to the correct boundary shape in a fraction of a second. A detailed application of the method to the water coning problem in oil wells is presented. INTRODUCTION The water coning problem in petroleum production is a prime example of a class of problems known as free surface problems. A free surface arises in fluid flow regions when the shape of the boundary of a single phase flow region is affected in some manner by the pressure or potential gradients within the region. When there exists an interface of two fluids of different densities, the shape of this interface will be determined by the relative velocities of the two fluids and will therefore comprise a free surface. Other free surface problems of interest to petroleum engineers include the gas coning, water injection, and gravity drainage probIcms. In each case it is desired to predict the shape of the boundary of the oil zone as a function of the flow rate, the well penetration and the physical parameters and dimensions of the system. Such problems do not lend themselves to the classical analytical treatments of boundary value problems because in this case the boundary of the potential field and the potential distribution within the field are interdependent and must be calculated simultaneously. A further difficulty arises from geometric considerations. Since the fluid flow is of the radial type in most cases, such effective methods as conformal transformation and the hodograph are not applicable. It is the purpose of this paper to present a method whereby free surface problems of this type may be solved rapidly to the desired order of accuracy by means of a combination of a network of electrical resistors and conventional analog computer units. The water coning problem is treated in some detail. Then the procedure for extending the technique to other free surface problems is indicated. FORMULATION Most commercial oil reservoirs consist of an oil-saturated sand, bounded above by an impermeable strata and below by a water-saturated sand. Gravimetric separation results in a horizontal oil-water interface. When an oil well is drilled so that it partially penetrates the oil zone, and production is initiated at a constant rate, the oil-water interface will assume a new shape as a result of the pressure gradients in the oil zone. It should be emphasized that this is a steady phenomenon. After an initial transient period the water phase will be completely static and only the oil will be in motion. The new steady-state shape of the interface, as shown in Fig. 1, depends upon the depth of penetration, d, the thickness of the oil zone, I, the production rate, q, the hydraulic permeability zone of the sand, k, the viscosity of the oil, µ, and the densities of the oil and water, p.,. and pw.. The problem is to determine this relationship. Darcy's law + = - (P f g p z).....(1) it.

Jan 1, 1957

By R. C. Mahon

The Homer iron-ore mine is at Iron River, Mich. Because it covers a large area, 400 acres, and because there was a considerable depth of water in the glacial drift above most of the ore bodies, this mine has presented a number of unusual and often difficult operational problems. The purpose of this paper is to discuss a few of the most important problems encountered. Surface Water Mining on this property was started on one 40-acre tract. The ledge in this area was the highest on the property and, although it was a real problem, water could be handled by underground pumping. During the first period of mining, drifts were driven just under the ledge and holes were drilled through to the surface material. In later years these drifts have been extended wherever possible. Although these drifts assisted in the drainage problem, it was evident they would not be sufficient alone. Before mining on a large scale could be started on this property, the water problem had to be solved. A number of test holes were put down to the ledge, and showed that there was an average 150 ft. of water-saturated glacial drift above the ledge over the rest of the mine. The upper 70 ft. was gravel and sand and the lower 80 ft. clay and hard pan, with some narrow seams of sand and gravel. It was evident that the water above the clay seam could not be drained off through openings in the ledge and for that reason it was decided to install surface drainage wells. This method of drainage was entirely new at that time and was pioneered at the Homer mine. The sinking of the first well was started in June 1929. Immediately following the first well a number of wells were sunk, but only to the top of the clay seam. This was done with the idea that a greater capacity could be obtained in a shorter time from gravel seams where the water flowed more freely and that the cost of pumping the water above the clay seam would be considerably less than if the wells had all been sunk to the ledge at once. Before the drainage of surface water was started, 1200 gal. per min. against a head of 800 ft. was being pumped from the mine. By March of 1932, with five surface wells in operation, the mine pumping had been reduced to 150 gal. per min. At this time we were pumping 5000 gal. per min., under an average head of 110 ft. from the surface wells. The total pumping costs were 30 per cent less than in 1929 because the greater capacity was being pumped at a much lower head. From 1932 to 1936 the mine was idle and all surface pumping was stopped. Since 1936, 10 new wells have been added with a total pumping capacity of 8000 gal. per min. at the present time. The water level has been lowered 70 ft. since surface pumping was started in 1929, and it is now approximately at the top of the clay. To remove the water below the clay seam, 11 of the 15 wells were sunk to the ledge.

Jan 1, 1946

By O. J. C. Runnalls, L. M. Pidgeon

Some observations on the kinetics of the iodide process are reported. The deposition rate is geometry-sensitive in a system containing a finely divided titanium charge. Further, results indicate that the iodine diffusion rate influences the velocity of the process. The nonvolatile iodide, Til,, forms in the hot filament zone, thus removing iodine from the cycle. TITANIUM metal of 99.9 pct purity may be prepared using a refining technique originated by Van Arkel and de Boer.' The purity of this metal, commonly called iodide titanium, exceeds that produced by any known process. In a recent application, the method was employed by Gonser et al.² to prepare titanium rods up to 2 to 3 cm in diam. In the Van Arkel-de Boer system, the relative influence of the fundamental mechanisms: l—production of titanium iodides, 2—gaseous countercurrent diffusion, and 3—decomposition, on the deposition rate have not been clearly established. Blocher and Campbell" have indicated that the controlling step in the process under practical conditions of operation may be the reaction rate of iodine with the crude metal. Fast' reported that crude titanium metal reacted with iodine rapidly, even at room temperature, in his apparatus. Little has been reported on the effect of gaseous diffusion or decomposition on the deposition rate. It is these aspects of the process about which this investigation is centered. An attempt has been made to separate these latter effects from those due to the formation of the iodides at the crude metal surface by a division of the experimental program. Reaction of Iodine with Titanium Apparatus: In the investigation of gas-metal reactions of this type, the chemical reactivity of the halogen and halide vapors dictates the use of all-glass apparatus. In such a system standard techniques for measuring reaction rates are difficult to employ. Here, a simple apparatus was devised (Fig. 1) so that some indication of the reactivity of titanium powder with iodine vapor could be obtained. A stream of iodine gas was evolved from a bulb of controlled temperature and passed over a sample of titanium powder heated in a horizontal tube furnace. The product of the reaction, TiI4, volatilized and was condensed outside the furnace in a series of four glass bulbs, each cooled to room temperature in turn. Preliminary experiments indicated that distillation was retarded in a sealed evacuated system due to a pressure build-up in the condensing end of the apparatus. Hence, the system was pumped continuously using a mechanical pump and two oil diffusion pumps in series, through a liquid air trap. The iodine bulb was made large and a capillary restriction was inserted between the titanium bulb and the condensers so that the iodine pressure over the metal would approach the equilibrium pressure over solid iodine crystals. The effect of this restriction on the evaporation rate of TiI4, was determined separately. The iodine bulb was heated in an oil bath controlled to ±2°C. The titanium bulb temperature was automatically controlled to ±5°C. Procedure: About 200 mg of —30 mesh titanium powder, weighed to 0.1 mg, was placed in the reaction bulb after part B had been joined to part A. The powder was tapped into a long (5 cm) shallow mass along the bottom of the tube. Two chromel-alumel thermocouples were inserted into the magnesium radiator which was clamped to the reaction

Jan 1, 1953

By B. R. Banerjee

MATERIAL used throughout this investigation was high-purity aluminum (99.998 pct). The 1/2-in. cubes were cut out of a cold-rolled slab and annealed at 550°C for 1 hr before deformation. The single crystal specimen was 1 in. in diam x 0.33 in. thick, cut from a cylindrical crystal produced by cooling at about 55°C per hr in a furnace which had a convenient gradient of about 10°C in every 4.5 in. vertical crucible length. Specific data on the ten specimens studied are summarized in table I. Three types of deformation were employed: (I) compression in a hand-operated hydraulic press; (2) impact with a 7-lb sledge hammer; and (3) rolling, using a wedge-shaped specimen' to obtain a gradient of deformations varying from 0 to 50 pct along the length of the wedge. Specimens were either deformed at room temperature, or first cooled in a freezing mixture of dry ice and ether at a temperature of —72°C and then deformed between steel blocks cooled with dry ice. The specimens deformed at the low temperature were ground and polished through 000 emery paper and wheels impregnated with alundum and alumina No. 1. During this entire procedure the specimens were dipped frequently in the freezing mixture of dry ice and ether in order to maintain constantly a frosty surface as insurance against overheating. All specimens were given a final electrolytic polish, using two different electrolytes* to insure that the surface effects observed were not char- acteristic of the polishing technique. With both electrolytes, the annealed specimens gave even surfaces with good polish. Several standard etchants were tried without success. The best results were obtained with an immersion etchant, developed in this connection, containing: hydrofluoric acid, 4 parts; nitric acid, 1 part; glycerine, 3 parts. Discussion of Results Typical strain markings have been observed within deformation bands, as shown in figs. 1, 2, and 4. By stereographic plotting of metallographic measurements, the strain markings within a deformation band in a single crystal of aluminum deformed by compression were found to be traces of (111) planes within a maximum scatter of 6". The edges of the deformation band were found to be traces of the (100) planes also within the maximum scatter of 6" (in agreement with previous workers). At 30 pct deformation, this scatter was considered quite normal because of the fragmentation and rotation of the crystal. This solution, based on the traces on one plane of observation is not unique, but as the planes were observed to be those normally and logically to be expected, further work in this regard was not felt to be necessary. The study of strain markings in a wedge-shaped specimen, rolled to obtain a gradient of deformation from 0 to 50 pct, revealed prominent strain markings at 25 pct reduction in thickness (fig.5). Faint and weak strain markings were visually observable up to a minimum reduction in thickness of about 12 pct. Since strain markings have been observed in other face-centered cubic metals after much smaller deformations;1, 2 and since the rate of recovery in aluminum is high, it is believed that, at lower deformations, self-recovery removes the localized strains at the slip interfaces, thus removing the source of the etching effects that give rise to strain markings. At high magnifications, strain markings sometimes seem to appear as very thin, light-banded re-gions bounded by a pair of dark edges. This so-

Jan 1, 1951

By A. W. Demmler

RECENTLY, Chaudron,&apos; Montariol,2 and their co-workers published the results of their studies on zone-refined aluminum. They found their material to be capable of recrystallization at —50°C, but gave no data as to the percentage reduction or time required. Their material was found to be practically non-work hardening at room temperature, but after 96 pct cold work at a low temperature and storage in liquid nitrogen it was found to recrystallize to coarse grains in less than 3 hr at 20°C. Recently, a study was made of the room temperature recrystallization characteristics of zone-melted aluminum. An ingot 14 in. in length, with a 3hx3 in. cross section, was made in an extremely high purity graphite boat under an atmosphere of dried commercial argon. It was made by first passing the molten zone along the ingot of 99.99+ pct A1 15 times. At this point, the most impure 3 in. (the end toward which the eutectic forming impurities migrated) were replaced with more of the original starting material, and 15 more traverses were made. Each traverse of the zone along the ingot required approximately 3 hr. Three ingots were prepared in this identical fashion and the chemical analyses were made spec-trographically on two of these ingots, rather than on the one used in this investigation. The analyses were made at 1 in. intervals along the ingot, in duplicate. Over the purest 5 in. of the ingot, which were most important in this investigation, there was found an average composition of <0.00004 pct Cu, <0.0003 pct Fe, <0.0001 pct Si, and <0.0001 pct Mg. In addition, the following elements were not detected spectrographically even in the more impure end of the bar: manganese, zinc, nickel, chromium, titanium, vanadium, lead, tin, boron, beryllium, bismuth, gallium, zirconium, cadmium, antimony, cobalt, and molybdenum. The original ingot was given several cold reductions, with intermediate anneals in order to refine the grains. Owing to the extreme length resulting and the ease of deforming the material plastically, it was cut into eight equal lengths and identified as shown in Fig. 1, with the highest numbered section at the purer end (that enriched with peritectic formers). Section 6 was used in the exploratory work and was found to be of exceptionally high purity, giving more rapid rates of room temperature re crystallization than any previous aluminum studied at the Alcoa Research Laboratories. This fact suggested that the entire midsection of the ingot might be of very high purity. Accordingly, section 4 was chosen for the next study. A portion of it was rolled to cold reductions of 10, 25, 40, 60, 75, and 90 pct at room temperature, and the re-crystallization of each specimen was followed by X-ray pinhole transmission photographs. The other portion received the same treatment, except that both the specimens and the rolls were maintained at 160°F in the process of rolling. The latter ortion was retarded in its recrystallization as compared to the former, probably due to the stress relief effect of the warm rolling. Both of these portions of the fourth section were found to recrystallize at a considerably slower rate than did the sixth section.

Jan 1, 1957

By R. C. Edwards, Will Mitchell, T. G. Kirkland

THREE years ago, when the Process Research Laboratory at Allis-Chalmers Manufacturing Co. sought a remedy for the increasing cost of disposing of great quantities of spent sands from foundries, R. C. Edwards developed a continuous inclined paddle scrubber which removed a substantial amount of the charred coatings from the grains with a surprisingly small amount of degradation of the sand itself.1 The satisfactory results obtained on foundry sand, using this piece of equipment in conjunction with classification, suggested that a similar procedure could probably be applied to the cleaning of other sands, such as those required by the glass and chemical industries. This paper describes the flowsheet and the results of tests performed on impure natural sands. The four materials tested were silica sands obtained from widely separated geographical areas. Three of the sands tested contained various amounts of iron oxide and the fourth an excessive amount of calcareous bonding material. The iron oxide was present predominantly in the form of grain coatings, which were scuffed by the paddle scrubber, and in all cases a product was manufactured which would meet one of the sets of specifications imposed by the glass industry&apos; The Edwards paddle scrubber used in these tests consists of a rubber-lined steel cylinder 18 in. in diam and 48 in. long, mounted on a frame so that its slope can be varied 5 ° to 35º from horizontal. This variable slope permits controlled flow of material through the machine. Rubber paddles rotate inside the cylinder and are secured to a center shaft 2 in. square, which extends through the entire length and is turned at both ends so that it can be supported by sleeve bearings centrally fixed in the end plates of the shell. At the upper or feed end it extends through the bearing on the end plate into a sheave, to which the motor drive is connected by means of Texrope transmission. The four sets of paddles mounted on the shaft, two in each set, are made of rubber belting, 1/4 in. thick, 9 in. wide, and 16 in. long. The two paddles in each set are secured on opposite sides of the square shaft, but in the same longitudinal position along the shaft axis. In other words, the two paddles in the set operate 180° apart. Each successive set is mounted 90º from the preceding one. One end of each paddle is bolted to the square shaft and the other weighted by a steel bar, 1x1 ½ x9 in. long, which is attached about 1/ 2 in. from the outer tip of the paddle. By centrifugal force at proper shaft speed, these weights force the paddle surface to rub smoothly against the rubber lining of the cylinder. During operation, the sand forces its way between the paddle face and the surface of the cylinder, providing the necessary abrading action as the pulp flows by gravity down the length of the cylinder. The capacity of the machine is limited by the amount and the hardness of the coating material and by the quality of product desired. The degree of scrubbing is governed by the retention time in the scrubber, which in turn may be changed by varying the feed rate, water content of the feed, and

Jan 1, 1952

By B. N. Webber

During World War II the Pocos de Caldas bauxite deposits of Minas Gerais in Brazil yielded some 60,000 tons. Since then they have maintained a small but almost continuous production. Known for many years, the deposits have been reconnoitered by a number of geologists,1-4 but no dimensional study has been possible because there have not been enough exposures to show clearly the depth, bedrock, and habit of occurrence. The deposits are somewhat unorthodox in their occurrence mainly on steep slopes of mountainous terrain. Although the parent rocks are a sequence of alkalic intrusions that bauxitize readily under the proper conditions, bauxitization has not been the dominant weathering process in the area. It is limited to certain localities where important volumes of bauxite have formed by laterization of several rock types, each yielding a distinctive type of bauxite. Bauxitization may be observed in several stages and in both direct and indirect cycles of formation. The deposits are unique in being of demonstrably recent age, so that the conditions under which the bauxite formed are essentially those of the present time. The bauxitization sequence is postulated in Fig. 1. Pocos de Caldas district is situated at approximately 21" 50&apos; south latitude and 46" 30&apos; west longitude in southwestern Minas Gerais, near its boundary with the state of Sao Paulo. It lies within the Eastern Plateau physiographic province of Brazil, occupying a prominent highland area that rises some 2000 ft above the surrounding country. The central portion of the Pocos de Caldas highland is characterized by gently undulating topography, with generally sluggish drainage, and is surrounded by a rim of hills rising above 1000 ft above it. In cross section the highland resembles a truncated cone with a depressed central area. The rim has been sculptured into a more prominent and abrupt topographic pattern than the central area, and streams that are of low to moderate gradient in the central plateau plunge over the rim in a spectacular series of cascades and falls. GEOLOGIC SETTING The Pocos de Caldas highland owes its physiographic expression mainly to the differential erosion of a complex intrusion of alkalic rocks into gneiss and sandstone. Erosion was guided somewhat by faulting. The highland is almost circular, and its limits, except in one locality, coincide with the periphery of the intrusion. The alkalic intrusions largely control its shape and extent, aided by some subsidence through faulting of the central portion. The mountainous rim of chilled phase, the later intrusions, and the indurated intruded rocks have resisted erosion more effectively than the central portion of the intrusion, which is composed of more coarsely crystalline alkalic rocks that form a central basin in the highland. Gneiss and sandstone are found coincident in elevation with the topographically highest intrusions. BAUXITE TYPES Most of the bauxite, which varies in physical type, is on the top and steep slopes of the northern rim. The only alumina mineral is gibbsite, definitely crystalline but iron-stained unless of secondary origin. Clay particles occurring with the bauxite are kaolinite. Some types of bauxite are an index to their origin. There are four general physical types of bauxite or bauxite laterite: 1) Surface Rubble: This partly nodular and partly fragmented type, usually less than 3 ft thick, results from surface weathering of massive bauxite or may form by superficial enrichment of nodular bauxite with a clay matrix when the interstitial clay is removed by surface runoff.

Jan 1, 1960

By Norman Weiss, H. W. Kaanta

CUSTOM ores reach across the New Mexican mesa to American Smelting & Refining Co.&apos;s new lead-zinc mill at Deming. The influx of ores justified increasing mill capacity from 12,000 tons per month to 20,000 tons per month with the installation of a second milling section. Deming mill has met a complex material handling problem with the successful instrumentation of modern machinery and knowledge. A tight, compact plant does a big job with the aid of the latest ore moving equipment. Location and Layout The mill is located three miles northwest of Deming in the tumbleweed covered valley of the Mimbres River, 30 miles north of the Mexican border. Deming has a population of 4000 and is about halfway between Lordsburg and Las Cruces and 54 miles southeast of Silver City. The AT&SF and the SP railroads and U.S. Highways 70, 80, and 260, cut across the mesa to the town. Asarco mill station is east of the AT&SF single track, and north of Deming. The nearly level terrain is covered with fine sand supporting only yucca and tumbleweed. Compacted gravel at depth affords excellent foundation bearing. The climate is semi-arid, but the district is underlain by water-bearing strata. Tailing disposal space is plentiful. The Deming site appeared favorable because of easy rail and highway access, central location in a mining district, excellent climate, plentiful water supply, space for all present and future requirements, and proximity to a town. The milling plant is a 250-ft square. The rail spur forms the west side; sampling plant, fine-ore conveyor and bins are on the east; track hopper, primary conveyor, and crushing plant lie on the south; and the mill building completes the north side of the square. Construction The mill site was chosen and the land purchased in 1,946 and 1947. Design began in 1948, and Stearns-Roger Mfg. Co. of Denver started construction in June 1949 completing work in April 1950. Construction is steel and concrete throughout, with main concrete floors supported on cellular steel beams. The building is covered by galvanized corrugated iron, attached to the frame by welded Nelson studs, and made dust tight at the joints with roofing paper and asphalt sealing compound. Crushing and Sampling Custom ores, delivered to the mill by railroad cars or trucks, are weighed on arrival. A Robbins car shaker dumps the ore into a 100-ton capacity steel hopper. Adjacent is a 40-ton truck hopper. Three 36-in. Pioneer apron feeders supply ore from the receiving hoppers to a 36-in. conveyor which runs to the crushing plant. A tramp-iron detector protects the primary crusher except when handling magnetite containing ores. A 2 ½ -in. spaced grizzly precedes the primary Traylor 24x36 in. jaw crusher set at 4 in. A Symons 4-ft cone crusher in closed circuit with 48x78 in. Robbins Gyrex screen completes crushing to 5/8 in. The discharges of both crushers drop upon a common conveyor, which, after gaining sufficient elevation, transfers ore to a return conveyor. This return conveyor passes under a suspended magnet and over a magnetic head pulley to the Gyrex screen. Screen undersize is conveyed by a 20-in. belt to the sampling plant. Crushing rate varies from 60 to 90 tons per hour. Ores containing magnetite and pyrrhotite nullify the magnetic detector and overload the magnets

Jan 1, 1952

By B. H. Kear, H. G. F. Wilsdorf

After a few percent strain, dislocations in disordered Cu3Au are arranged in groups in ulell-defined slip planes, which contrasts with the more or less random distribution of dislocations in the corresponding ordered alloy. Unusually long and straigkt dislocation segments observed in the ordered alloy are interpreted in terms of cross slip of screw dislocations from their slip planes into cube planes. It is proposed that cross slip, and also dislocation reactions of the Lomer type, play an important role in work hardening of the ordered alloy. ACCORDING to to dislocations in the disordered lattice are only partial dislocations in the corresponding super lattice, so that in the super-lattice dislocations must occur as pairs, with each pair connected by a ribbon of antiphase boundary. Recently, striking confirmation of the theory was obtained by Marcinkowski, Brown, and Fisher3j4 in a study of dislocation configurations in thin foils of the Cu3Au alloy by transmission electron microscopy. In the present investigation, the observations made by these workers have largely been confirmed. Moreover, it has been found that dislocations in the plastically deformed ordered alloys are often unusually long and straight. This paper is mainly concerned with these new observations. A tentative explanation is offered in terms of cross slip of dislocations in the ordered alloys. PREPARATION OF SPECIMENS An alloy close to the stoichiometric composition Cu3Au was prepared by melting together high-purity copper and gold (99.995 pct) under vacuum in a graphite mold. The resulting ingot was rolled down and cut into strips 1 1/2 by 1/8 by 0.005 in. in thickness. All strips were annealed at 900°C for 3 hr and cooled to 500&apos;~. A few of the strips were quenched from ~OO&apos;C, while the remainder were slowly cooled in the temperature range 400" to 150°C at intervals of a few degrees every 24 hr to produce a high degree of order. After this annealing treatment the average grain size of the material was about 0.1 mm. Material in different states of order was obtained by reannealing fully ordered material at temperatures below the critical temperature: followed by quenching. The equilibrium degree of order attained at a particular reannealing temperature was obtained from the paper by Keating and warren.&apos; A simple hand-operated tensile jig was used to give the strips the required amounts of plastic strain. Following straining, a number of specimens were cut from each strip by means of an electrolytic cutting device.= Finally, each specimen was thinned electrolytically using the polishing procedure described by Bakish and Robertson,7 and these thin sections were examined in the Philips EM-100B electron microscope operating at 100 kv. EXPERIMENTAL OBSERVATIONS Antiphase boundaries. The average domain size in the ordered alloys was found by direct observation to be about 0.25 p. Also, it was observed that the grown-in configuration of antiphase boundaries was changed little by plastic deformation, at least up to 6 pct strain. Fig. 1 shows an electron micrograph of a thin foil of partially ordered alloy (S - 0.8) after 3 pct strain. The micrograph shows a few dislocation pairs and a somewhat crystallo-graphic network of antiphase boundaries. The normal to this foil was found by diffraction analysis to be approximately 11121, with principal directions in

Jan 1, 1962

By H. I. Aaronson, C. Laird

Cold rolling by 50 pct a A1-4 pct Cu alloy containing many 0&apos; plates has been found to accelerate markedly the transformation of 8&apos; to 0 upon further aging. Although the basic mechanism of this transformation remains unchanged by plastic deformation, the nuclea-tion kinetics of 8 become appreciably more rapid and also less dependent upon temperature. Particularly at lower aging temperatures, rounded idiomorphs replace several faceted rnorphologfes. The rates of growth of 9 idiomorphs in deformed specimens aged at 300°C are appreciably more rapid than simple volume diffusion control allows. This observation is shown to be explained by an excess vacancy, rather than by a dislocation Piping mechanism of growth. ThE rather complex phenomenology of the 8&apos; —8 transformation in Al-Cu alloys has been recently elucidated in considerable detail by means of transmission electron microscopy.&apos;-4 This technique was also employed in the present investigation in order to examine the effects of plastic deformation upon the transformation of 8&apos; to 8. The mechanism of the transformation in undeformed Al-Cu alloys has been established as the following sequence of events.1"4 The first step is the nucleation of 9 at (Y:8&apos; boundaries. Nucleation of a 0 crystal takes place, however, at only a very small proportion of the 8&apos; plates present. Each 0 crystal simultaneously consumes the host 8&apos; plate and the a! in the immediate vicinity, with growth into a being the rate-controlling process. The remaining 8&apos; plates are then dissolved as they fall under the concentration shadow of the growing 8 crystals. The evidence on the effects of plastic deformation upon these processes is intriguing, but much less detailed. The careful X-ray studies of Graf and Guinier have shown that the aging times required to form detectable amounts of 8&apos; and 8 are reduced by prior cold working. Thomas and Nutting confirmed these results by replication electron microscopy. Nile-shwar,* on the other hand, reported that creep deformation decreases the rate of formation of 0. While this difference may have been caused by the use of concurrent rather than successive deformation and ag- ing, the X-ray technique which he used was able to monitor only the 0 phase. It is thus possible that the times needed to form 8&apos; were increased moreg than the kinetics of 8&apos; — 8 transformation were accelerated. At 90 pct deformation by cold rolling, Graf and Guinier found that the usual 0&apos; —0 8 sequence is reversed: 0 forms first. von Heimendahl 10 confirmed this result with transmission electron microscopy. Pollard and Nutting, 11 and more recently Driver and Barrand, 9 having used the same technique, report that 9 also forms first during creep deformation. In the present study, the maximum amount of deformation was limited to 50 pct reduction by cold rolling in order to insure that 8 formed principally by the decomposition of . I) EXPERIMENTAL PROCEDURES This investigation was conducted on an Al- 3.93 pct Cu alloy, prepared as previously described. 4 Morphological and crystallographic effects of plastic deformation were studied in specimens annealed 6 hr at 548°C, quenched, and then aged for either 3 or 8 hr at 250°C to form large numbers of 0&apos; plates. After cold rolling to a 50 pct reduction in thickness, the

Jan 1, 1969