Search Documents

By E. DeGolyer

The problem of good engineering practice and. of good conservation practice in oil production is that of keeping gas in solution. This can best be done by producing a field as a water-drive field. Some degree of water drive is believed to be present in most fields but in the past most fields have been produced too rapidly to allow water drive to be effective. Ultimate recovery should be So per cent greater for fields produced by water drive over that from gas-expansion fields. Wide spacing will permit fields of low-degree water drive to be produced effectively as water-drive fields. INTRODUCTION NEGLECTING all the complicated scientific and technical argument that leads to the conclusion, the solution of the problem of good production practice, of good engineering practice, and of good conservation practice in oil production is to keep gas in solution. This can best be done by producing fields at a rate low enough to make effective the water drive, which exists, it is generally believed, to a degree great enough to be made effective in more than 80 per cent of the fields of the United States. Oil is being so produced in the Ten Section field of California; the Hobbs field of New Mexico; the Yates, Hastings, Friendswood, Anahuac fields and the main sand of the Conroe pool, in Texas; the Magnolia pool in Arkansas, and doubtless in many other pools. The measures of success in the efforts to achieve the solution of the problem are the maintenance of bottom-hole pressure and the prevention of an increase in gas-oil ratio. Some decline from the original bottom-hole pressure and the production of some gas are essential. A pressure gradient from the reservoir to the well is necessary and at least as much gas must be produced as that in solution in a barrel of oil. Once the optimum pressure and the gas-oil ratio have been established, they should be maintained. How common is water drive in oil and gas pools? General opinion is that some degree of water drive is almost universal. Theoretically, this conclusion appears to be a sound one. According to our present understanding of the processes of sedimentation, we would expect to find all sands or sandstone charged with connate water unless it had been displaced by some other fluid, such as fresh water percolating into the beds at the outcrop, or oil and gas, or gas only, in reservoirs. The fact that the original pressure of the fluid system in most reservoirs is approximately that of the hydrostatic head of water for the corresponding depth indicates that the sands are charged with water, and common experience in drilling into the extensions of the porous zones beyond the reservoir is to find them watercharged. The very fact that oil and gas pools have substantial pressures in their original undisturbed state indicates either that a reservoir is a rigid, closed system, a con-

Jan 1, 1941

By F. W. Bloecher

S. Mortsell and J. Svenssofi (Royal Institute of Technology, Stockholm, Sweden)—Bloecher states that the apparatus described by him should be a suitable instrument in the mineral dressing laboratories for determining the specific surface of such granular products that are generally investigated. We want to express a somewhat different opinion, as we doubt that the gas adsorption method of surface measurement really is the most suitable method in mineral dressing laboratories. It is well known that the surface area, as measured by this method, does not coincide with the surface area calculated from the size, shape, and number of particles, i.e. the superficial surface of the particles. It can be seen easily from Mr. Bloecher's own determination on ilmenite-leucoxene concentrate that the surface area measured according to this method may be several hundred times larger than the superficial surface. It is supposed that the surface of cracks, fissures, and pores within the particles also is included in the measured surface. However, this is an assumption which scarcely can be proved and certainly has not been proved. We believe that the mineral engineer could better use a method giving the superficial surface of the particles, as in most cases this surface only is of importance to him. Such is certainly the case when calculating the resistance of the fluid flow through granu- lar materials and the capillary forces of such materials, problems which are of great importance in connection with dewatering, filtration, and pelletizing'" etc. The same may also be the case when studying flotation problems, partly since the quantities of the introduced reagents usually are so small that they can only cover the most accessible surface of the particles, and partly since the molecules of at least the collecting reagents are so large that they cannot enter the smallest cracks and pores. As to the surface, which is of consequence in the application of Rittinger's law of crushing, one is inclined to believe, from theoretical reasons and from the work by Gross and Zimmerley, that the total surface here is the most important one. However, it seems as if in that case the superficial surface was as important as the total surface. Other reasons making the gas adsorption method less suitable for use in the mineral dressing laboratories are that the granular materials there very often are too coarse to be measured by this method, that the experimental technique is rather difficult, and that it takes a long time to measure the specific surface of a sample. Besides, the validity of the method must still be considered questionable. It is thus well known that with different gases one usually gets different values of the specific surface of the same sample, which values, even with such an ideal material as metal foils, can differ as much as about 50 pct.'" Still more serious

Jan 1, 1952

By C. M. Marquardt

Tramp iron and steel moving on a conveyor belt cause small currents to be generated in a coil situated in a strong magnetic field, which are converted to an alternating current and are amplified. The output voltage from the amplifier fires a thyratron with a relay in its anode circuit, which actuates a howler and simultaneously drops a spot of marker material on the belt. THE problem of tramp iron removal from moving ore belts is a long standing one. When heavy ore streams are carried on a belt, magnetic pulleys and strong surface magnets fail to remove tramp buried in the ore stream. Tramp iron buried in the ore stream cannot be pulled from the bed by surface magnets and is carried past the magnetic pulley by the falling ore stream. With the increased use of detachable bits the problem of the detection and removal of tramp has become more necessary and difficult. Several types of tramp detectors have been developed. It would serve no practical purpose here to review exhaustively the literature on the subject. Methods of tramp detection used are: (1) The magnetic method, wherein the small current generated by the magnetized tramp passing a Coil is used. (2) The unbalanced oscillator method wherein the tank circuit of a stable radio- or audio-frequency oscillator is unbalanced causing a change of frequency or a change in plate current due to changes in eddy currents, hysteresis, or dielectric because of the presence of tramp. (3) The bridge methods wherein the impedance of one leg of an alternating current inductive bridge is changed due to the presence of conducting tramp. Each of these methods of tramp detection has its field of usefulness. The second and third methods are excellent for oxide iron ores, coal, sand and gravel, grain, etc. However, these latter methods are not suitable for use on ores that contain rich conducting sulphides, since a large piece of pyrite or galena will cause the same detector response as a piece of tramp iron. At the Caselton, Nevada, plant of the Combined Metals Reduction Co., sulphide ores are treated; therefore, it was necessary that a tramp detector operating on only the magnetic properties of the tramp iron be used. Tramp iron detectors of this type operate on the principle that if a piece of tramp iron moves near a coil in a high intensity, steady magnetic field, the presence of the moving tramp iron causes the magnetic flux lines through the coil to change. This induces a mall current in the Coil. In series with the Coil is generally placed a relay sensitive to currents of 1 to 3 microamp. When the tramp iron passes near the coil the flux linkages change, causing this very sensitive relay to actuate. Since the contacts of such a relay are very small it must actuate a second relay capable of breaking a larger current

Jan 1, 1951

By C. M. Marquardt

Tramp iron and steel moving on a conveyor belt cause small currents to be generated in a coil situated in a strong magnetic field, which are converted to an alternating current and are amplified. The output voltage from the amplifier fires a thyratron with a relay in its anode circuit, which actuates a howler and simultaneously drops a spot of marker material on the belt. THE problem of tramp iron removal from moving ore belts is a long standing one. When heavy ore streams are carried on a belt, magnetic pulleys and strong surface magnets fail to remove tramp buried in the ore stream. Tramp iron buried in the ore stream cannot be pulled from the bed by surface magnets and is carried past the magnetic pulley by the falling ore stream. With the increased use of detachable bits the problem of the detection and removal of tramp has become more necessary and difficult. Several types of tramp detectors have been developed. It would serve no practical purpose here to review exhaustively the literature on the subject. Methods of tramp detection used are: (1) The magnetic method, wherein the small current generated by the magnetized tramp passing a Coil is used. (2) The unbalanced oscillator method wherein the tank circuit of a stable radio- or audio-frequency oscillator is unbalanced causing a change of frequency or a change in plate current due to changes in eddy currents, hysteresis, or dielectric because of the presence of tramp. (3) The bridge methods wherein the impedance of one leg of an alternating current inductive bridge is changed due to the presence of conducting tramp. Each of these methods of tramp detection has its field of usefulness. The second and third methods are excellent for oxide iron ores, coal, sand and gravel, grain, etc. However, these latter methods are not suitable for use on ores that contain rich conducting sulphides, since a large piece of pyrite or galena will cause the same detector response as a piece of tramp iron. At the Caselton, Nevada, plant of the Combined Metals Reduction Co., sulphide ores are treated; therefore, it was necessary that a tramp detector operating on only the magnetic properties of the tramp iron be used. Tramp iron detectors of this type operate on the principle that if a piece of tramp iron moves near a coil in a high intensity, steady magnetic field, the presence of the moving tramp iron causes the magnetic flux lines through the coil to change. This induces a mall current in the Coil. In series with the Coil is generally placed a relay sensitive to currents of 1 to 3 microamp. When the tramp iron passes near the coil the flux linkages change, causing this very sensitive relay to actuate. Since the contacts of such a relay are very small it must actuate a second relay capable of breaking a larger current

Jan 1, 1951

By Morris Muskat, J. M. McDowell

In both production and refining operations of the oil industry many processes are controlled by the gas-liquid phase relationships of the hydrocarbon mixtures of interest. The quantitative behavior of fractionating or distillation columns and stills depends on the changes in the equilibrium distributions of the hydrocarbon components between the gas and liquid phases as the pressure or temperature conditions may vary along the length of the column or as the gross operating parameters and compositions are varied. In oil producing operations the nature and amount of gas phase developed within an underground reservoir as it is being depleted and its pressure declines also involve the basic equilibrium gas-liquid phase interactions. The influence of surface conditions of temperature and pressure and various separation procedures on the nature and amount of stock tank oil and natural gas recovered from a given well stream is likewise determined by the same basic phase equilibrium characteristics of the hydrocarbon systems. Such equilibrium separation of the gas and liquid phases in a well stream is of importance both in establishing optimum separator conditions for obtaining maximum stock tank oil yields and in the general problem of crude stabilization. The phenomena involved in these problems and their quantitative aspects can, of course, be established in each individual instance by appropriate laboratory experimentation. It has been found, however, that by associating with the individual hydrocarbon components functional characteristics de- scribing their individual gas - liquid phase equilibrium behavior, the phase properties of the composite mixtures can be predicted by mathematical computation. These characteristics have been termed "equilibrium constants", or "equilibrium ratios"," and are defined by the general equation: where K, is the equilibrium ratio for the jth component, y, is the rnol fraction of that component in the gas phase, and xj is the corresponding mol fraction in the coexisting liquid phase. Considering the Kj as representing available and measurable properties of the individual components of a mixture, and as defined by Eq. (l), it is readily shown that in a coexisting gas-liquid system the rnol fraction concentrations of the individual components in the gas phase, y,, and those in the liquid phase, x,, are given by the expressions: where the nj are the corresponding rnol fraction concentrations in the composite system, and ng is the mol fraction of the whole which is in the gas phase. The basic unknown in Eq. (2) is n,: which gives the gross separation between the gas and liquid phases. This may be determined in principle by imposing the requirement that the sums of the mol fractions in both the gas and liquid phases are unity, i.e. by the equations: The solution of the equivalent Eqs. (3) lying between 0 and 1, when inserted into Eqs. (2), provides a complete description of the compositions of the coexisting gas and liquid phases. While the Eqs. (3) are essentially equivalent to polynomial equations, such transformations are of little value when dealing with multicomponent sys-

Jan 1, 1949

By J. M. McDowell, Morris Muskat

In both production and refining operations of the oil industry many processes are controlled by the gas-liquid phase relationships of the hydrocarbon mixtures of interest. The quantitative behavior of fractionating or distillation columns and stills depends on the changes in the equilibrium distributions of the hydrocarbon components between the gas and liquid phases as the pressure or temperature conditions may vary along the length of the column or as the gross operating parameters and compositions are varied. In oil producing operations the nature and amount of gas phase developed within an underground reservoir as it is being depleted and its pressure declines also involve the basic equilibrium gas-liquid phase interactions. The influence of surface conditions of temperature and pressure and various separation procedures on the nature and amount of stock tank oil and natural gas recovered from a given well stream is likewise determined by the same basic phase equilibrium characteristics of the hydrocarbon systems. Such equilibrium separation of the gas and liquid phases in a well stream is of importance both in establishing optimum separator conditions for obtaining maximum stock tank oil yields and in the general problem of crude stabilization. The phenomena involved in these problems and their quantitative aspects can, of course, be established in each individual instance by appropriate laboratory experimentation. It has been found, however, that by associating with the individual hydrocarbon components functional characteristics de- scribing their individual gas - liquid phase equilibrium behavior, the phase properties of the composite mixtures can be predicted by mathematical computation. These characteristics have been termed "equilibrium constants", or "equilibrium ratios"," and are defined by the general equation: where K, is the equilibrium ratio for the jth component, y, is the rnol fraction of that component in the gas phase, and xj is the corresponding mol fraction in the coexisting liquid phase. Considering the Kj as representing available and measurable properties of the individual components of a mixture, and as defined by Eq. (l), it is readily shown that in a coexisting gas-liquid system the rnol fraction concentrations of the individual components in the gas phase, y,, and those in the liquid phase, x,, are given by the expressions: where the nj are the corresponding rnol fraction concentrations in the composite system, and ng is the mol fraction of the whole which is in the gas phase. The basic unknown in Eq. (2) is n,: which gives the gross separation between the gas and liquid phases. This may be determined in principle by imposing the requirement that the sums of the mol fractions in both the gas and liquid phases are unity, i.e. by the equations: The solution of the equivalent Eqs. (3) lying between 0 and 1, when inserted into Eqs. (2), provides a complete description of the compositions of the coexisting gas and liquid phases. While the Eqs. (3) are essentially equivalent to polynomial equations, such transformations are of little value when dealing with multicomponent sys-

Jan 1, 1949

By P. G. Chamberlain, E. R. Podnieks, R. E. Thill

Although published data on the physical properties of rock are voluminous, information is often lacking on the environmental conditions under which such data were acquired. Efforts are frequently directed to improve specimen tolerances and preparation procedures; but investigators often overlook giving the rock environment equally careful control during the testing program. Generally, tests are conducted at existing laboratory room conditions, and the prepared rock specimens are frequently, if not most commonly, air-dried for various lengths of time before testing. The standard testing atmosphere recommended by the American Society for Testing & Materials (ASTM)1 is 73.4°F and 50% relative humidity. To maintain a rock at 50% relative humidity for testing purposes, however, requires special equipment and preconditioning procedures, as this study demonstrates. Relatively small variations in the moisture content of a specimen, for example, due to the coolants or lubricants used during specimen preparation, can cause significant variations in the physical properties measured. Such moisture variations may occur in the rock specimen even after it is air-dried, since laboratory humidity conditions commonly fluctuate from day to day. For these reasons, this study emphasizes procedures for preconditioning and maintaining a controlled environment during testing. Although the effects of moisture or temperature on rock properties have previously been studied, their combined effect on rock properties is unknown. In this study, uniaxial compressive strength, Young's and stiffness moduli, and longitudinal wave velocity were determined and compared under controlled conditions of temperature, moisture, and pressure for 11 environments considered to be of particular interest in laboratory, in-situ, and even simulated lunar environments. The following environments were selected for this program: -250°F under dry, 50%

Jan 1, 1972

By R. V. Ramani, R. M. Mishra, Y. J. Wang

The validity of the concept of mine resistance in ventilation systems is examined. Mine resistance is the proportionality constant relating the head generated by a fan and the quantity flowing through it when the fan is connected to a mine circuit. It is the total effect of all branches in the mine ventilation circuit. Its importance lies in the fact that for new mine projections, and in the extensions of existing mines, ventilation calculations are usually based upon adjustments of the mine resistance. In ventilation circuits with regulation, and/or with multi-fans, simple adjustments of the mine resistance curve do not lead to correct solution. A ventilation system consists of several interconnected subsystems where one subsystem behavior affects that of the others, and the total system. Through a series of simple but realistic examples, the authors demonstrate the importance of the systems concept in mine ventilation, and its practical application to coal mine ventilation planning. Starting from an initial system with no leakage and one fan, more complex ventilation networks with several leakages, sections and fans, are analyzed to show that ventilation system design on the basis of total systems approach is the correct procedure.

Jan 1, 1979

By Michael P. Richardson

INTRODUCTION This paper is intended to be a summation of the state-of-the-art i n draw theory and draw- point spacing. Knowledge of this very important factor in the successful design and operation of a block caving mine is scarce and nonconclusive. It is hoped that the presentation of this paper will stimulate interest and discussion which will lead to a stronger understanding of these a1 1 important factors. Please note that block caving as used here- in refers to block, panel, and mass caving systems in general, not just to the specific system of block caving where discrete blocks of ore are prepared and caved as a unit. DRAW THEORY The knowledge of draw theory as related to the practice of block caving mines is, unfortunately, very limited. In recent years much work in draw theory has been done in respect to sublevel caving systems and an understanding of draw mechanics relating to sublevel caving seems to be emerging. This work is certainly helpful to those of us interested in block caving but the question of "what goes on up above" still hounds us since we are more interested in the region of draw which begins just above the area where sublevel caving interest ends. Herein is presented a brief summary of draw theory with an attempt to look at the factors which can help our understanding of the area of draw influence in block caving mines. Nature of Gravity Flow An understanding of the flow of granular material (rock, sand, grain, or prill as examples) is the first step toward understanding block caving draw. If we take a supported column of granular material and allow gravity flow through an aperture at the bottom of the column, an ellipsoidal shaped zone of disturbance of the in-place material will form and grow with extraction of material through the aperture. The volume of this zone of disturbance or loosening is about 15 times the volume of material extracted at any given time (Kvapil, 1980). Figure 1 shows the development over time of the zone of disturbance. The ellipsoid of disturbance represents a future ellipsoid of extraction which will equate to the volume of materia1 extracted by that future time. Extraction involves the movement of the particles located vertically over the drawhole directly downward while material outside this direct vertical volume moves radially inward and down toward the drawpoint as shown in Figure 2a. Figure 2b shows the result of this motion on originally horizontal strata within the ore column. Increased draw increases the eccentricity of the ellipsoidal volume or, in other words, the ratio of the height over the width of the disturbed area increases as ore is withdrawn from the column (Kvapil , 1980). This becomes important to block caving since eventually a vertical cylinder of draw will be approximated as this ratio increases without bounds. Figure 3 shows this result. The width of this draw cylinder is a critical dimension for the determination of draw point spacing in relationship to block caving mine design. McCormick (1968) for one, felt that within this cylinder of draw, mass flow would take place. This is the

Jan 1, 1981

By M. R. Tek, K. H. Coats, D. L. Katz

In natural gas storage operations, seasonal pressure fluctuations in the gas reservoir cause the water from the surrounding aquifer to flow into and out of the gas sand. The theory of unsteady-state liquid flow through porous media developed by Van Everdingen and Hurst' has been applied to predict the water movement into and out of the gar bubble for .several .postulated pressure cycles. Those cycles with as many pound-days above the original aquifer pressure as pound-days below, may cause the gas reservoir to slowly grow or shrink rather than hold to a constant volume. Applications to an actual field case study give the predicted gas reservoir monthly pressures and volumes as compared with the observed monthly pressures and volumes. INTRODUCTION A large number of natural gas storage reservoirs are bounded by or adjacent to large water-saturated formations called aquifers. The presence of these aquifers is usually evidenced by the production of water from wells delineating the gas-hearing sands. Some gas storage reservoirs in use today have been purposely developed on aquifers. Cyclic pressure variations in a gas storage reservoir cause water influx and efflux from the surrounding aquifer. This, in turn, results in a varying gas reservoir volume. The prediction of the effect of this aquifer fluid movement on the size and size variation of the gas reservoir can provide information valuable in the study of several reservoir engineering problems. The economics of gas storage operations are directly influenced by the influx of aquifer fluid into the reservoir since a shrinking storage reservoir requires increasing pressures for the storage of the same quantity of gas. Material balance and reserve or recovery calculations also obviously require knowledge of reservoir volume. Various other reservoir engineering calculations such as interpretation of well interference data, evaluation of physical characteristics of porous media, water coning, gas injection and pressure maintenance studies are typical problems where variations of volume due to edge or bottom-water encroachment becomes important. The solution of equations describing influx and efflux of water in the gas sand, application to gas storage reservoir behavior and interpretation of results are the main objectives of this paper. While this work was directed toward gas storage reservoirs, it applies equally well to repressuring of partially depleted oil reservoirs with an active water drive. MATHEMATICAL ANALYSIS As just mentioned, the cyclic pressure variations in an aquifer-surrounded gas storage reservoir cause water movement and varying gas reservoir volume. Prediction of this volume variation from the reservoir pressure cycles or the injection-production schedule requires adoption of a flow model, certain assumptions concerning reservoir and fluid properties, and formulation and solution of the governing differential equation. The flow model used in this study is a gas bubble located on a very large aquifer (Fig. la). Gas bubble radius and aquifer sand thickness are denoted by rr and h, respectively. Fig. lb shows the horizontal, radial two-dimensional porous reservoir attended by the unsteady, compressible motion of the aquifer liquid. Volume variation of the gas bubble is determined from aquifer water flow across the cylindrical boundary, r = r0

By James E. Lawver, James L. Wright

This paper describes the design of a cell used to measure the electrical conductivity, or the reciprocal resistivity, of granular materials. It also establishes a quantitative relationship between the electrical conductivity and the electrical separation of selected mineral samples. It is estimated' that the free world produces about 13 million tons of mineral concentrates a year by electrostatic or electrodynamic methods. At least 95% of these concentrates are produced by corona discharge type machines that separate minerals by exploiting the differences in their electrical conductivity. But, what is meant by the electrical conductivity of a mineral? How large a difference in the electrical conductivity of two mineral species is necessary to effect a separation? Just what is the role of conductivity in electrical separations with regard to capacity and selectivity? There is a considerable amount of information in the literature on both the mechanisms of conduction and the values of the electrical conductivity of pure single-crystal mineral specimens. In addition, some insight into the role of mineral conductivity can be obtained by referring to a Bureau of Mines publication' in which 95 minerals have been grouped as conductors or insulators as a function of temperature. The classification was made on the basis of the percent of weight that reported as "conductors" in an electrical separator. But, as is often the case in the mineral industry, practical application leads theory — and there is little useful information in the literature giving any kind of quantitative relationship between electrical conductivity and electrical separations. The problem is a bit complex because electrical conductivity per se — which can be rather easily measured on large, single grains — is not sufficiently informative to permit quantitative predictions of the separability of the mineral system. Practical "high-tension"* separations are made at such feed rates that the band of minerals on the rotor is multilayered in thickness. Thus, the effective conductivities of minerals as seen by a high-tension machine include particle-to-particle contact resistance, which is often a controlling factor in making a separation. This is particularly true when the mineral grains are coated with slime or with a dielectric surface film. From a high-tension separation viewpoint, one is actually concerned with the time required for corona-charged grains to lose enough charge so that the centrifugal force acting on the particles exceeds the image force holding the grains to the rotor. This calculation requires a knowledge of the effective mineral conductivity s. (The conductivity of the metal rotor is sufficiently greater than that of the minerals so that it need not be considered in charge decay calculations.) The charge density at time t can be approximated by the relaxation equation.3 where t 5 charge density at time t r, - charge density when t = 0 cr e total electrical conductivity £ = permittivity The time required for the charge density to fall to l/e of its initial value is called the relaxation time and is numerically equal to €/n. AS defined here, u is the conductivity of an element of homogeneous grains making contact with each other and with a grounded rotor. This paper deals with the design of a conductivity cell used to measure a, or its reciprocal p, the electrical resistivity. CELL DESIGN Initial test work was performed with a cell recommended by ASTM.4 Since the reproducibility with the ASTM cell was not satisfactory, it was decided to

Jan 1, 1970

By Horace Pops, L. L. Isaacs

SOLID-STATE transformations at low temperatures are frequently studied by optical metallography. Greninger and ooradian' and Hull and Gar-wood2 have examined the martensitic-type transformations in 0-phase Cu-Zn alloys during continuous cooling below room temperature. The lowest range of temperatures in the apparatus described by these investigators is limited to approximately 110°K. Present studies of reversible first-order phase transitions near liquid-helium temperatures have necessitated the design of a new cold-stage cryo-stat for optical metallography. The features of interest of this instrument are as follows: a) temperatures down to 4.Z°K are obtainable; b) the specimen is always under vacuum, thereby avoiding the condensation of moisture; c) specimens can be rapidly cooled or heated at varying rates, thus permitting studies of transformation hysteresis. Fig. 1 shows the details of the cryostat. All major parts are made of type 304 stainless steel. Both helium and nitrogen cans are Heliarc-welded to the helium filling tube, permitting the use of a common shielding can. Hence, the over-all weight and the area of the evacuated surface are mini- mized. The copper sample holder is screwed into the bottom of the helium can. To assure good thermal contact between the sample holder and the refrigerant, an indium ribbon is placed on the threads

Jan 1, 1964

By A. M. Gaudin, T. P. Meloy

This paper presents the theoretical derivation of the distribution equation for single fracture. The equation is shown to accord with experiment. Several empirical size-distribution equations have been proposed to describe the size of broken materials. Among them are the Gaudin-Schuhmann equation and the Rosin-Rammler equation.3*4 The Gaudin-Schuhmann equation relates the relative fraction of undersize to relative size —. In this relationship Mo is the total weight of crushed sample, M(x) the weight of undersize contained, x the size considered, K a quantity called the size modulus, which together with the slope parameter, m, characterizes the product. The slope parameter is usually close to unity. The Rosin-Rammler equation relates the same relative fraction of undersize to the relative size modulus by an equation of different form In this relationship, e is the base of natural logarithms. In the fine size-range when m is unity both equations give Gilvarry and Berstrom have sought a size distribution equation having a sound theoretical basis. They have come to an equation taking into account the effect of volume, surface and edge flaws in fragmentation. If the effect of the volume and surface flaws is neglected, the equation taking only edge flaws into account has the form of the Rosin-Rammler equation. In the present paper, a theoretical size-distribution

Jan 1, 1962

By E. P. Barrett

THE high-frequency laboratory induction furnace with a rotating liquid crucible enables research workers to conduct certain investigations heretofore very difficult or impossible to realize because vessels are not obtainable that are capable of resisting the physical conditions or the chemical actions to which they are subjected. Applications for patents covering commercial uses of centrifugal liquid crucibles were filed in the United States in 1919,1 in France in 1925, in the United States and Germany in 1926,2 and in France in 1927.3 In 1928, Schuette and Maier,4 of the Bureau of Mines, reported the construction of a whirling table beneath a high-frequency induction furnace. SHAPE AND SIZE OF CENTRIFUGAL LIQUID CRUCIBLES When a vessel containing a liquid is rotated, the inner surface of the liquid takes the shape f a paraboloid under the simultaneous action of centrifugal force and gravity. The internal dimensions of the paraboloid rotating liquid crucible are governed by the diameter of the container and its speed of rotation. Melted Wood's metal was poured into cylinders 2 ½ in. in diameter, which were rotated at 180, 300, and 468 r.p.m. When the metal was solid, a slurry of plaster of Paris was added, and rotation continued until the plaster had set. Fig. 1, a photograph of sections f the cylinders, shows the effect f speed f rotation of the containers upon the shape f the inner surface f the rotating liquid crucibles.

Jan 1, 1938

By A. T. Schwennesen

Every engineer has occasion to trace or copy a map, plan, or other drawing on paper too thick for the ordinary way of using tracing-cloth or tracing-paper. When the figure is small and simple a copy may be made by holding the original against a window-pane, coverin& it with the paper, and tracing direct by the aid of the strong sunlight from outside. The need of utilizing this principle on a larger scale and in a more convenient position led Dr. J. C. Branner to plan the table of which the following is a description : This table was first made in the form of an adjustable glass-top table with a mirror beneath, in 1887, while Dr. Branner was State Geologist of Arkansas. Later it was modified as experience suggested until the form as here described was evolved. The device consists essentially of a drafting-table with a plate-glass top, upon which the original drawing and the paper are laid, and a mirror mounted underneath to reflect the light of the sky up through the drawing. The glass top is hinged and fitted with two arms and thumb-screws, so that it can be raised and fixed to any position, either inclined or horizontal. The mirror is pivoted and revolves about a horizontal axis, so that it may be tilted to any angle. The hood of cardboard or black cloth prevents the reflection of light from the tracing, and may or may not be attached to the table.

Jan 1, 1912

By W. P. Lass

(San Francisco Meeting, September, 1015) THE gold precipitate from the zinc-dust presses in the cyanide plant of the Alaska-Treadwell Gold Mining Co.; Treadwell, Alaska, is treated, in the refinery adjoining, by the Tavener or lead-smelting method. About. 3 or 4 tons of this precipitate are produced monthly having a gold assay value of $40,000 to $60,000 per ton. It was formerly the practice to treat the by-products from this process, consisting of 2 tons of slag, 300 lb. of matte, 500 lb. of refinery refuse, flue dust, etc., in a 24-in. water-jacketed blast furnace. This' practice was discontinued in the summer of 1914 by reason of the difficulty of keeping the lead-well open when treating a high-grade lead product; of preventing the loss of gold in the flue dust; and of avoiding injury to the general health of the refinery operators; a plain single-phase electric furnace was substituted for the blast furnace. The furnace was constructed from an old steel acid drum by cutting off the top and introducing a cable, made from strands of bare copper wire, through the bottom and spreading the strands out fan-shaped on the inside of the drum. Powdered graphite, obtained by grinding up old crucibles, mixed with 10 per cent. cement, was tamped wet into the bottom of the drum, around and completely covering the copper wires. The graphite was carried up to the bottom of the furnace, or lead-well, and acted as the lower electrode. The sides were built up of ordinary firebrick forming a melting chamber 14 in. in diameter by 20 in. high.

Jan 7, 1915

By H. S. Coe, G. H. Clevenger

Engineers have long recognized the desirability of correlating the data obtained from small-scale slime-scttling tests with commercial work as carried on in large tanks. This need, though most apparent in designing new installations, frequently arises also in existent plants, since a large range of experimental work can be performed without interfering with regular operation. General Settling Phenomena In order to develop rational methods of laboratory testing, it becomes necessary to study the general phenomena of settling. Since it was desired to give the public the benefit of these methods at as early a date as possible, together with the knowledge of the general principles of slime settling necessary for a clear understanding of the laboratory tests, we have ventured to discuss the subject in so far as brought out by the work which we now have under way. We realize that certain of our preliminary conclusions may be subject to modification, but it seems probable that, with but few exceptions, the general laws enunciated will cover the settling behavior of all pulps encountered in metallurgical plants. However, it must be recognized that there is still a vast amount of work to be done upon certain phases of the subject; therefore, at this time we will attempt only a discussion of the behavior of ore pulps during the process of settling or dewatering, under certain given conditions. The laws and principles controlling these conditions are not fully established, so that a complete discussion of them will not be attempted in this paper. In metallurgical practice, slime pulp consists of water, finely divided sand

Jan 1, 1917

By L. H. Simons, H. H. Spain

I NT RODUCTION Theory indicates that linear water-floods should exhibit scaling and stabilization properties in both oil-wet and water-wet porous media'. Experimental verification of these proper-ties in oil-wet media was obtained some time ago', and more recently, Perkins', employing a high permeability unconsoli dated sand and a low oil-to-water viscosity ratio, has obtained flooding data in a water-wet medium which follow the pattern of scaling and stabilization. Also, Root and Calhoun3 have found similar trends in the displacement of gas by liquids from unconsolidated sands. In general, however, the experimen-tal evidence appears still somewhat conflicting since scaling and stabilization of water floods in water-wet media has not been observed in most of the studies to date'.".'. The purpose of this paper is to provide a more comprehensive picture of waterflood behavior in water-wet media and to corroborate the validity of the scaling and stabiliza-tion concepts. The need for differentiating between the intrinsic nature of water-oil displacements inside a porous medium and perturbating secondary end effects is discussed, pertinent experimental procedures are outlined and the results of flooding tests conducted at low and at high oil-to-water viscosity ratios on con- solidated, water-wet Alundum cores are analyzed. END EFFECTS IN WATER-WET MEDIA Outlet End Effects The peculiar feature of the outlet end effect in water-wet cores is that it not only results in an excessive wetting phase saturation at the outflow face,'.' but that it also retards the moment of water breakthrough: i.e., causes an undue delay in the appearance of water in the produced effluent. Conditions existing in a water-wet core when water first arrives at the outflow face are schematically shown in Fig. 1. At this flooding stage the saturation distribution, Fig. la, has not yet been distorted by the outlet end effect. A water-invaded pore at the outlet core face, opening into the oil-filled void space between the end of the core and the end plate of the flooding cell, is illustrated in Fig. lb. The curvature of the water-oil interface is concave toward the outlet, and the pressure on the water side of the interface is lower than on the oil side by an amount equal to a certain capillary pressure (Fig. lc). Before the water (of this particular pore) can be produced from the core, it is apparent that the pressure in the water phase must exceed that in the oil outside the core. Accordingly. when water first reaches the outlet face, it will not leave the core but will accumulate inside, and only oil will be produced. Eventually, as the water injection is continued. sufficient pressure is built up in the water to reverse the curvature of the interfaces in the outlet pores, and only then will water be produced from the core. This stage, illustrated in Fig. 2. corresponds to the conventional "water breakthrough" observed in flooding experiments. For purposes of discussion, it is convenient to distinguish between the flooding stage at which water first arrives at the outlet face of a core (Fig. 1) and the stage at which water is first produced from the core ( Fig. 2). The former will be referred to as "water arrival" and the latter water breakthrough. In oil-wet media

By L. D. Godshall

The extreme difficulty of obtaining a short and, at the same time, exact method for the determination of gold and silver in copper-materials has been well illustrated in "Assays of Copper and Copper-Matte," and its discussion, by Dr. A. R. Ledoux and other leading authorities on this subject.* Two general methods were used by the numerous assayers who took part in the symposium initiated by Dr. Ledoux, and whose results are given in the paper and discussion. One of these is the dry or fire-method, consisting of scorification and cupellation, the former being repeated if the percentage of copper is very high, all slags and cupels being assayed and the results so obtained added to the ordinary assay; and the copper retained by the silver buttons being determined and deducted from the combined weight of the buttons obtained from the assay of the original material, the scorification-slag, and the cupel. The other is the wet or combination-method, which, while not involving so much work, requires a longer time. Briefly, it is as follows : The material to be assayed is dissolved in nitric acid, the solution is diluted, and the fine undissolved gold is collected by means of sulphate of lead, formed by the addition of lend acetate and sulphuric acid to the solution, After standing from 12 to 24 hours, the precipitate is filtered off, and the silver in the filtrate is precipitated as a chloride or bromide, and collected by means of sulphate or bromide of lead. The solution containing this precipitate in suspension is again allowed to stand until the precipitate has settled. It is then filtered; both precipitates, containing the gold and silver, are dried, ignited and scorified, either separately or together, and the result is cupelled in the usual way.

Jan 1, 1901

By William Vietti

WEST TEXAS and New Mexico has been overshadowed by the develop-ment in East Texas to such an extent that the area has been placed on a settled production basis by most of the operators. Considerable develop-ment work on both proven and unproven acreage remains to be carried on, but the incentive, a ready and profitable market, has been lacking. The main characteristics of the fields in this area are so well known that they are not described again in this paper, which thus resolves itself into a statistical review of the more important production features of the area. Proration has been in effect during the year and has been rigorously applied with the full cooperation of all producers. Proration in West Texas and New Mexico is based in the more pro-ductive fields on a potential and acreage distrbution of the allowance to the individual wells or acreage units. Potentials are determined generally by a short production test of from 1 to 4 hr.; and the hourly rate is multiplied by 24 to obtain the 24-hr. production or rated potential of the separate wells. The potential values thus set up have been questioned by many production men who are not willing to concede that the instantaneous (hourly) capacity of a well to produce is its potential capacity for a day with all other wells in the pool producing at their capacity. However, the potential of a well determined as above remains its chief rating as a measure of the permeability in place and as an indication of the possible reserve feeding that well. , The acreage factor has made it unnecessary to overdevelop properties in order to obtain an allowance proportionate to neighbors who are willing to drill an excessive number of wells on a piece of acreage in the hopes of a quick drainage and a corresponding profit. Proration has resulted in an orderly development of many of the pools in this area on the base as out-lined above, resulting in more reasonable spacing of wells and the more even withdrawal of oil and the ensuing expectation of high recoveries.

Jan 1, 1933