Search Documents

By Arthur West

It is the purpose of this paper to describe briefly some recent large power stations for blast furnaces, where the blast is exclusively supplied by gas engines using furnace gas. The stations are given in the chronological order in which they were designed, in order to indicate the various improvements suggested by experience. Fig. 1 shows the blowing-engine station of the Bethlehem Steel Co. at Bethlehem. Although the picture shows only five blowing engines, the house now contains 11 engines. In the diagrammatic plan the arrow shows the position and direction of camera. This station handles five modern blast furnaces of 450 to 500 ions capacity each. In this, as in all the other stations described in this paper, each furnace is blown by two single tandem gas engines. Ten engines are thus required for five furnaces, leaving one single tandem spare engine. This spare capacity has been shown by several years' experience at Bethlehem to be adequate to insure continuous operation. The engines in the Bethlehem station are right hand and left hand, arranged in pairs. The outboard bearings of each pair are close together so that there is not room for passageway between them. On the right of the picture are shown the inclined drums communicating with the cold-blast lines outside of building, so that any engine may be operated on any furnace. The illustration shows four cold-blast gate valves with pipes passing through wall, but since the photograph was taken the drums have been extended to take care of a fifth valve for a fifth furnace. At the extreme back of the picture can be seen the tubs of three twin vertical-horizontal Southwark steam blowing engines, which, although of modern design and as good as new, are not operated because of the greatly reduced blowing cost shown by the gas blowing engines. The next station built is shown in Fig. 2. This is the plant of the Minnesota Steel Co. at Duluth, Minn., and is at present constructed for five engines, to handle two furnaces, with one spare engine. The engines are of practically the same size as those at Bethlehem. Instead of being arranged in right-hand and left-hand pairs, as at Bethlehem, all the engines are of the same hand; this arrangement has some ad-

Jan 1, 1915

By AIME AIME

THE Wednesday morning session was devoted entirely to the consideration of the tentative code for coal mine ventilation. A. W. Hesse is chairman of this subcommittee. E. A. Holbrook presided at the session and assisted by A. W. Hesse and George S. Rice, gave the historical background of the movement for a ventilation code. They stressed the point that this was to be an engineer's code, and that it was hoped that it might serve as a valuable guide to operating companies in securing greater efficiency as well as safety in ventilation. The discussion was continued into the afternoon session, and by adjournment the entire' code had been covered.' Many sections were referred back to the Committee for further study and several new sections were suggested. The various opinions and new ideas brought out during the discussion proved very valuable and. contributed much to the progress being made in the preparation of this code.

Jan 1, 1929

By O. D. Gonzalez, R. A. Oriani

The migration of hydrogen and of deuterium dissolved in a iron and in nickel induced by an applied electrical potential has been measured over a range of temperature. In all cases the intevstitial solute migrates to the cathode. The deduced charges of transport are positive, independent of or slightly dependent on temperature, and markedly larger for the beavier mass. These results are interpreted as showing predominating momenlum transfer between electron holes and the acticated complex of the elementary diffusion act. THE migration of components of a metallic system under the action of an applied electrical potential is called electromigration or electratransport. This phenomenon has been known since 1861 and is becoming of increasing interest to metal scientists because of the opportunity it offers to explore the connections between mass transport and electron transport. Until recently, reliable data have been very scarce because of the difficulties inherent in the measurements. In addition, theoretical understanding has been either nonexistent or rudimentary and at present this situation is only moderately improved. Whereas the prevalent notion had been (and is still widely held) that electromigration directly reflects the state of ionization of a component in its equilibrium state in the metal, it is now becoming clear that the major, if not the sole, factor is the momentum transfer between the charge carriers, themselves in motion because of the applied field, and the metallic components in their activated state. It becomes important therefore to obtain reliable data over a range of temperature on electrornigration in systems where only one component moves, that is, either in pure metals (vacancy motion) or in interstitial solid solutions. Our choice of systems was dictated by our measurements' of the Soret effect in solid solutions of hydrogen and deuterium in iron and nickel. Indeed, the main reason for making measurements on electromigration at all is that we suspected a mechanistic connection between thermal diffusion and electromigration. In our former paper' we proposed that what is common to both phenomena is the momentum transfer between the charge carriers in the metal and the atom as it jumps from one equilibrium position to another. In Soret diffusion, however, there is in addition the dissipation of the energy of the jumping atom via pho-nons. We have since found that similar ideas for this interconnection have been developed by Fiks.2 In the present paper we will discuss in more detail our understanding of the mechanism of electromigration itself, but we turn first to a presentation of the experiments and results. EXPERIMENTS AND RESULTS Let us consider a metallic system in which only one component, m , can diffuse at the temperature in question, and to which are applied simultaneously an electrical potential gradient, grad cp, and a chemical potential gradient, grad p,. One may write3 for the material flux Jm and the electronic charge flux Je by applying the condition, grad = 0, to Eq. [I] and evaluating grad(um/T) for the isothermal case and for activity coefficient independent of composition over the relevant composition range. ere, c is the concentration and D the diffusivity of the mobile component. The experimental technique that we have used to measure Z* for the isotopes of hydrogen individually dissolved in each of two transition metals has been developed from a method used by Wagner and Heller.4 (A somewhat similar method was also used by Herold.5) A wire or thin rod of the metal under study connects two volumes of gaseous hydrogen at identical pressures; hence grad um = 0. A direct current is made to pass through the specimen, serving to maintain the specimen at the desired temperature and also to produce the electromigration of the hydrogen dissolved in the metal in equilibrium with the gaseous hydrogen. Under these conditions, the flux of hydrogen from one volume to the other is given, from Eq. [I] for grad( um/T) =0by

Jan 1, 1968

By AIME AIME

FEW mining engineers-noted as the profession is for migratory predilections.--can point to as varied a record as Scott Turner, director of the U. S. Bureau of Mines and newly elected vice-president of the Institute. His record as printed shows that from the time of his graduation from the Michigan College of Mines in 1904 until he went to the Bureau in 1925, he worked for 21 different companies. Geographically the record is no less imposing, although one reason for this is the fact that he was field engineer for several exploration companies. Virtually every important mining state in the Union is represented in addition to Canada, Alaska, Panama, and several countries each in South America and Europe. In addition to all of the common metals he has mined tin and coal. He opened and operated for five years a group of coal mines in 73" 13' S. Lat., on the Island of Spitzbergen. This was 825 miles north of the Arctic Circle on No Man's Land, where Mr. Turner claimed and maintained pos- session under the American flag of an area of 600 square miles. Incidentally, he was a survivor of the ill-fated Lusitania, sunk by a submarine in May, 1915.

Jan 1, 1930

BUMPS in No. 2 Mine, Springhill, N. S., furnished the main feature for discussion at the morning meeting* on Ground Movement and Subsidence on Feb. 18. Walter Herd, the author of the paper by which the discussion was introduced, not being well, was unable to be present. The paper was presented by T. L. McCall, who laid stress on the presence of sand- stone as the cause of bumps, on the value of retreating longwall in eliminating such phenomena at the coal face and on the advantage of wide headings with packs on either side, leaving space behind them for any coal that bumps might dislodge. George S. Rice, who presided, referred to his visits to the Nova Scotia mines and said that bumps usually occurred only where the coal was thick and strong and the roof and floor both more than usually hard. If any of the three were weak, bumps were not likely to occur. In the Nova Scotia mine, to which Mr. Herd referred, there was no material for packwalls and for this reason as well as for safety he had been convinced that long- wall retreating with a small percentage of pack walling was the most feasible plan.

Jan 1, 1929

By J. V. N. Dorr

DEADWOOD and the Black Hills were familiar names to me from childhood, for. I had an uncle who was among the earliest eastern investors there and I used to hear of the Uncle Sam mine and its rich ore back in the eighties. The spring of my junior year at college, in 1893, brought me an offer of summer work at the Deadwood & Delaware smelter, in Deadwood, and full of the thrill of the long journey from New Jersey, I went out as chemist and stayed four months. Within a week or two of my arrival, I went through the tragic experience of seeing an associate drink cyanide by mistake and die within a few moments. I shall never forget the horror of feeling that my lack of knowledge of an antidote might be responsible for his death, but I found later that the solution he drank was so strong that nothing could have been done. A year after graduation, when I had settled down to chemical research work in New York, an offer came to go back to the smelter in Deadwood, and within a few days I was again tramping down "the Gulch" with my lunch bucket and putting in the standard assay office shift of that day, from 7 a.m. to 6 p.m., with a half-day off on Sundays. During my absence East, the D. & D. smelter had been changed from a pyritic smelter, using native pyrite, and Homestake concentrate to matte the siliceous gold ores, into a copper-matting smelter using copper ores brought from Butte, over the newly-completed Burlington rail-road. The work was interesting, and the laboratory offered many opportunities for making improvements. I remember also undertaking experiments at home on a new method of gold precipitation for the chlorination process and leasing a mine in Strawberry Gulch that promised great things, but soon petered out.

Jan 8, 1927

By Clemens Jones

THE analytical history of phosphorus in its relation to the metallurgy of iron is an interesting study, the progress of which runs parallel with the development of the greatest industry in the world. Without the means of finding out how much phosphorus crude pigiron contained, the Bessemer steel process would have been impossible. To do this was originally tedious and slow work. On the other hand, the " direct" process of to-day, as well as the various special processes for steel or iron, have demanded the utmost rapidity in the operations of analytical chemistry. In general, any rapid process for the conversion of unrefined metal into a product of standard composition depends upon the rapidity of some accurate means employed to control it. Moreover, in our modern practice, it is not improbable that the differences in physical properties among the various makes of iron or steel are affected, if not produced, by the use of different methods of analysis. Recourse is always had for correction to the ((standard methods," but I incline to think that these methods are susceptible to error. It is very certain that the system of duplicates would not be resorted to, if the fact were otherwise. Even when duplicated, under the most careful and skilful manipulation, these standard methods produce disagreements. In proof of statements like these, which may sound. heretical, I hope, further on, to cite some evidence worthy of attention. I do not now mean to lay claim to the distinction of discovering the ultimate corrective. That result will come, no doubt, in. time, as the product of the experience of many workers. In the case of phosphorus, as of the other ingredients of iron or steel, a great deal has been done to accommodate the methods of analysis in rogue to the growing necessity for more rapid procedures: Much of this work has concerned what might be called the incidents of method. There is no better example of the accumulation of these incidental improvements than the work done on phosphorus; and I

Jan 1, 1890

By J. B. Umpleby

PRoduction engineering in 1927 may be characterized by a great. clarification of fundamental conceptions, and many improvements in technique. During the year the profession has received tnarked recogni-tion by the industry and to an extent never before attained has become an integral part of it. History Petroleum production engineering is a new profession. Prior to 1925, when this Institute undertook the work, no forum existed for the open discussion of its technical problems. There was no attempt at a handbook of the subject prior to "Petroleum Production Methods by J. R. Suman, in 1921, and no textbook prior to Petroleum Production Engineering" by L. C. Uren, in 1924. As late as 1926, only six schools and universities offered special courses in petroleum production engineering. Prior to about 1923, engineers engaged by oil companies were used almost exclusively for construction and location work. Two of the leading production engineers in the Mid-Continent field, although with their respective companies more than twelve years, were not definitely assigned to production work until 1924. Both men now head large departments giving almost their entire time to production problems. Because of the newness of the profession, the leading production engineers of today have had their fundamental training in mining, civil, mechanical and electrical courses. Not unlikely this diversified training is in considerable part responsible for the amazing growth of the profession. I believe, however, that recognition is due principally to economic pressure within the industry which has directed attention more and more sharply on costs and efficiency. After all, the justification for the growth and continued development, of the profession is to recover more oil from a given unit of sand at less cost per barrel. In this new profession, it seems to me that greatest progress will result from focusing thought and effort on this single objective, and if I might offer one suggestion to the com-

Jan 1, 1928

By F. E. Crane, H. A. Kendall, G. H. F. Gardner

Two effects of a difference in density may be observed in miscible displacement. As the difference is increased from zero there is first a change in mode from multiple fingers to a single finger. A further increase results in a more rapid growth of the single finger. Miscible displacement with multiple fingers has been discussed by Blackwell, et al, whereas miscible displacement with a single finger has been discussed by Craig, et al. In the present paper experiments are described which bridge the gap between these extreme cases. INTRODUCTION Craig, et al,1 investigated the effect of gravity on frontal displacements for circumstances in which the gravity forces were significant. Blackwell, et a1,2 dealt with the other extreme in which gravity forces were negligible. The considerable difference between their results is illustrated in Fig. 1 where the breakthrough recoveries are plotted against the mobility ratio. The experiments described in the present paper were conducted to examine how the transition from the one extreme case to the other occurs when the gravity forces are gradually reduced. The transition is well illustrated by the production history after breakthrough. Fig. 2 shows how the number of pore volumes which must be injected at a constant rate to displace 98 per cent of the original fluid depends on the gravity force. For each mobility ratio there is a transition range, and a very significant change in the number of pore volumes occurs when this range is traversed. This range of the gravity force is physically linked with the formation of viscous fingers. A single finger is predominant for larger gravity forces; a multiplicity of fingers is formed for smaller gravity forces. Improved recovery and the occurrence of multiple fingers is concomitant with a large increase in the amount by which the fluids are mixed within the porous medium. The transition range depends on all the dimension-less groups which characterize the problem; but this dependence has not been exhaustively studied as yet and only fragmentary results are discussed in this paper.

THE CHALRYAN.--I think that we have set the stage for the balance of the sym- posium. Most of the emphasis has been placed on the immediate value of every- thing we can do and everything we can learn for the furtherance of the war effort. I believe that ought to be first, but I also believe that this is the time for us to con- sider very seriously not only what these improved methods and techniques do to form a closer approach to ideal segregation but what effect these great quantities of scrap metals and alloys that are going to be produced this year and next, are going to have-what their impact will be-on post- war industry in general and in particular ,, on the primary metals fields. In some cases we have been hearing in the last month or two of the law of diminishing returns coming to the fore. We find alloy simplification growing and certain alloys being produced in great quantities, which will perhaps drop out of the picture some- what as the war ends but never to the lower ( stage they had before. We have I think a pretty good cross- section of the producers, the refiners, the reclaimers and ingot makers, the ultimate users here, and there ought to be some good and helpful discussion. The papers are open for discussion. Mr. Beattie, do you want to make any 1 comment? H. J. BEATTIE.*-To start the discussion I might ask Mr. Deitz what they do with manganese bronze turnings? We segregate the manganese bronze turnings from the other bronze turnings. The value of it seems to be much out of line with the price of ingot, that is, as compared to some of the other alloys like 88-10-2 or 85-5-5-5. I assume it is because they can only use a

Jan 1, 1943

By George Newton

When Mr. Bailey asked us to present a paper describing our new BOF shop, he requested that we avoid a presentation heavily laden with detail and statistics. Not only have we attempted to do this, but also we have prepared a number of colour slides which, hopefully, will provide you with a graphic conception of the facility. The installation of the BOF facility at the Steel Co. of Canada's Hilton Works was delayed many years because of the remarkable production growth of the oxygen open hearth furnaces in No. 3 shop. However, in mid-1960 it became strongly evident that not only would increased ingot capacity be required, but also that N0.2 shop - with vintage non-oxygen open hearth furnaces - would have to clean its stacks in the near future, or be closed down. A decision to embark on the BOF facility was made in 1967 after an extended period of in-depth planning and assessment of industry trends.

Jan 1, 1972

By F. H. Deily, L. W. Ledgerwood, J. E. Eckel

A new method for drilling the earth's formations has undergone extensive laboratory and shallow earth drilling experimentation. This method, pellet impact drilling, uses the energy of a large mass of high velocity steel spheres to break and crush the rock. Pellets are confined to a region close to the hole bottom. Motive fluid for transporting and recycling the pellets is supplied by a modified jet pump. The pellet drilling method has inherent advantages over conventional rotary drilling. First, only a nominal amount of weight need be applied to the hole bottom. Second, only a very small amount of torque is required for bit rotation. Third, means are available for continual replacement of the cutter medium. The experimental laboratory work and analytical procedures necessary for the design of a pellet drill bit are described. In the laboratory program approximately half the effort was devoted to the development of a better understanding of the physical process, and half to the empirical testing of new bit configurations. Factors such as pellet size and velocity, jet pump characteristics and modifications, and power distribution are discussed. The design and construction of a pellet impact bit for drilling a 9 in. hole with 1 1/4 in. steel pellets are described. Drilling performance in representative rocks, hydraulic operating characteristics, and metallurgical problems are discussed. INTRODUCTION This paper discusses an attempt to reduce drilling costs through the development of a drilling method basically different from rotary drilling. Publications on drilling research indicate that the major effort on the part of manufacturers and operators has been confined to research in rotary, or rotary-percussion drilling. This applied drilling research has produced significant gains in drilling rates and bit life, but thus far it has failed to achieve any major decrease in general drilling costs. From recent statistics released by Drilling Contractors, it can be shown that the total cost of drilling an "average" well in 1953 was about 2 1/4 times the corresponding cost in 1935. Analysis of the costs will show that they are not due to inefficient field operations; they are due instead to both an inflated economy and greater "average" well depths. Diligent work by the industry has reduced the backlog of potential economic improvements in rotary drilling to a group of rather marginal prospects. Increasing depths and poorer quality reservoirs at these depths continue to make the drilling cost problem more acute. Hence, the aim of the work reported here was to develop a new drilling method not limited by the inherent characteristics of rotary drilling and thus capable of attaining further significant reductions in drilling costs. The effort devoted to research on this proposed new drilling method was of considerable magnitude and represented .in excess of 37 man-years of research. The affiliates of Standard Oil Co. (N. I.) sponsored this development program which was conducted by the Drilling Methods Section of the Carter Research Laboratory in Tulsa, Okla. The purpose of this paper is to

Jan 1, 1957

By Paul B. Crawford, Bobby L. Landrum

An electrical model study has been mode to estimate the effect of horizontal fractures in thick reservoirs on pattern conductivity. For the patterns studied, it is shown that fracturing all the wells in the pattern in-creases the conductivity considerably more than frac-turing only single wells. For certain conditions one large fracture is more effective in increasing conductivity than several fractures of half the radius. Particularly in thick reservoirs and with large fractures, the center of the pay is found to be more responsive than other locations. For the seven-spot pattern fracturing the center well is more effective in increasing pattern con-ductivity than fracturing all outer wells with fractures of the same size. INTRODUCTION Although commercial fracturing has been used for some time very little quantitative information is known about the effects of fractures on reservoir behavior. The purpose of this work was to estimate the effect of horizontal fractures in thick reservoirs on the con-ductivity of various flooding and cycling patterns.2 Circular fractures originating at the wellbore and extending symmetrically into the pay were considered. ANALYSIS Electrical models were used in making this study. Horizontal fractures were simulated by copper sheets shaped like the fractures and of a proportional size; the wellbore was simulated by a copper wire. A dilute salt solution served as a conducting medium. A con-ductivity bridge was used to measure the conductivities of the various patterns studied. EFFECT OF HORIZONTAL FRACTURES ON CONDUCTIVITY Fig. 1 shows the effect on square and staggered line drive patterns of horizontal fractures located in the center of the pay. The model is shown schematically in the insert. The upper and lower groups of lines show the effect on conductivity when all wells are fractured, and when only one well is fractured, respectively. In general, pattern conductivities are substantially improved by fracturing all wells. Fig. 2 shows the effect of multiple horizontal frac-tures on the conductivity of a line-drive pattern. At

Jan 1, 1958

By R. Steinitz, J. L. Orehotsky

An analysis was made of the influence of floating molten zone traversal on the purification of tungsten rods and the effect of this purification on the brittle -to-ductile transition temperature. The major impurities detectable in the original rods, i.e., molybdenum and oxygen, were reduced by zone refining from 30 to 3 Ppm. Changes in the trace amounts of other impurities could not be quantitatively determined since they were below the limit of detection. Tensile tests on 3-mil wires, drawn from these rods and recrystallized to 17,000 grains per sq mm, showed a transition temperature of 60°C for the zone Purified and 175°C for the original material. 1 HE brittle-to-ductile transition temperature is manifest mainly in the bee metals, iron,' molybdenum, chromium,3 tungsten,4 and niobium. Since many of these metals cannot be fabricated at room temperature in a commercially pure annealed poly-crystalline state, a considerable amount of work has been done on evaluating the influence of purification on the transition temperature in order to determine indirectly whether the fabricability of these metals can be improved by removing impurities. Smith and Rutherford8 showed that the transition temperature of iron is lowered significantly by zone purification. Working with chromium, Edwards, Nish, and wain7 found also that purification appreciably lowered the transition temperature. A similar evaluation has so far not been reported for tungsten, probably because of the difficulties in obtaining tungsten in a purified polycrystalline state. carlson8 and, more recently, schadler9 have purified tungsten rods by floating zone traversal, but after zone traversal, their rods were single crystals. To obtain high-purity polycrystalline tungsten, a technique has to be round for transforming the zone-purified single crystal material into a suitable polycrystalline structure. The purpose of this investigation was to obtain zone-purified tungsten in a suitable polycrystalline state and then to evaluate the effect of zone purification on the transition temperature.

Jan 1, 1962

By N. Standish

Heat transfer coefficients have been measured in beds of various packings irrigated with mercury and molten fusible alloy countercurrent to hot gases. The measured coefficients for both systems were found to increase with gas velocities and liquid rates. Correlations were determined which show this dependence and also indicate that heat transfer in these systems is influenced by the liquid flow characteristics and the thermal conductivity of the gas and the solid packings. A heat transfer model has beer2 proposed which explains the various features of the experimental results. On the basis of this study, which gives an insight into the heat exchange in the melting zone of the blast furnace, it was concluded that by comparison with the furnace stack heat transfer coefficients are about 1.5 times higher in the melting zone. EACH year large tonnages of metal are produced in operations which, in part, involve liquid metal irrigation of "packings" countercurrent to hot gases. The melting zone in blast furnaces and in cupolas is a good example of packings irrigated with a liquid melt countercurrent to gases. In all instances of this kind large amounts of heat are exchanged and it is desirable to have some knowledge of heat transfer phenomena involved in these systems. So far the most common method of analyzing furnace efficiencies, fuel requirements, and the general thermal state of the furnace has been through the use of heat balances. As heat balances are essentially statements of the first law of thermodynamics they give no real indication of the factors which govern heat transfer between phases in the various zones of blast furnaces. Hence, rational improvement in production efficiency and the development of theoretical models is only possible if the heat transfer characteristics are known at every stage of the process and related to the important variables involved. This has been generally recognized for some time but it was only recently that Kitaev et al.' have produced a comprehensive treatment of heat transfer in solid-gas countercurrent systems such as the blast furnace stack and the packed bed regenerator. Using their treatment it is now possible to predict the effect of particle size, thermal conductivity, bed porosity, and the flow rates of both the gas and the solid material on the heat transfer in the blast furnace stack. However, the stack of a blast furnace is only one part of an integral unit for which the heat transfer analysis cannot be complete without also considering the heat exchange in the melting zone. The complexity of heat transfer processes in this region of the furnace has so far escaped quantitative description. Yet, the melting zone accounts for a greater amount of heat exchange than all the other zones of the furnace put together. Moreover, if the reduction of oxides in the melting zone proceeds in part in the liquid state the importance of heat transfer on furnace productivity and on the metal and slag temperatures is obvious. THEORY Heat transfer for two-phase flow in packed beds is a complex problem involving a number of heat exchange paths for which interphase areas are not known with any degree of certainty. Analytical solution is, therefore, difficult. This difficulty is emphasized by noting that Rabinovich~ and Luck have only recently solved the steady-state heat transfer for simplified two-phase heat exchangers of known area. However, useful progress can be made for the system considered by making a not unreasonable assumption that the usual heat transfer considerations apply and restricting treatment to the steady state. For these conditions the rate of heat transfer dq in a height dz of a packed bed of unit area is: dq = UaATdz [I.] Integration of Eq. [I] then gives the total heat transferred: assuming both U, the overall heat transfer coefficient, and a, the interphase area, to be independent of bed height. Since a, in these systems, is unknown it is convenient to combine this term with U. The group U, then represents the overall heat transfer coefficient on a volumetric basis. If AT is linear with q, then for a bed of unit volume Eq. [Z] can be integrated to give: is the log mean of terminal temperature differences. From Eq. [3] U, can be readily calculated as q and {AT)im are experimentally obtained quantities, but a difficulty arises in interpreting its meaning. Two approaches are possible depending on whether the effect of packing in the transfer of heat is neglected or not. If the packing is thermally decoupled then the resistance concept gives the relationship: which states that the overall resistance is the sum of the gas phase and the liquid phase resistances (assuming areas are equal throughout). Because the resistance to heat transfer in liquid metals is negligible by comparison with that of the gas,4 Eq. [4] can be simplified, i.e.:

Jan 1, 1969

By LESTER W. STRAUSS

OUR early knowledge of history and geography attracted most of us to the mineral resources of South America. The romantic tales of the Spanish activities, which were curiously alluring, and Prescott's exceptional bi-Conquest histories-Mexico and Peru-no doubt fired our minds with the .then metallic wealth of the Spanish colonies. Later developments, intensified within the past eighty years, have, however, changed its fame which now rests on such metallics as copper and tin, and among the non-metallics on nitrate of soda and petroleum. South America proper, excluding Panama, is made up of thirteen countries, a coincident parity with our original thirteen States. Its area is given as 7,231,300 square miles, or slightly less than North America (8,037,000 square miles), is made up as follows:

Jan 1, 1930

By David B. Rushmore

Torches were used by the early Romans for mine-lighting, and these were followed by open lamps or earthen jars filled with tallow or oil, and later by candles. In early coal-mining, explosive gases seldom occurred, and, if they were encountered, the danger of explosion was materially diminished by the absence of any ventilating-system and the consequent insufficient circulation of air to form with the methane an explosive mixture. As the art advanced, the danger of fire-damp became more apparent, and methods for testing the air were resorted to as early as in the fifteenth century. The method of testing consisted in lowering a dog in a basket down the shaft. As soon as he encountered fire-damp he would commence to howl, after which he was withdrawn, and a leafy bush was fastened to the end of the rope and run rapidly up and down the shaft. This so disturbed the accumulation of gas as to cause it to rise out of the shaft. Later this odd method of testing was improved upon through the discovery that a light inserted in a body of fire-damp Gould produce a blue flame. Candles were used for this purpose, and, when fire-damp was thus discovered, brushing or some other primitive method of fanning was resorted to for driving out the gas. In some instances the gas was burned away, regardless of the danger thereby incurred. A man, wearing a well-moistened coat and a mask with glass spectacles, descended in the mine a few hours before each shift. With a long stick, to which was fastened a burning torch or candle, he would crawl on the floor with the stick so raised that the light would sweep the roof and ignite the gas which it encountered. In this position the flame of the explosion would pass over him, after which he would retreat from the gases resulting from the combustion. The occurrence of serious accidents resulted in

Jan 1, 1913

By Harry W. Brown

This paper presents results of static capillary pressure measprements made both by the restored-state and by the mercury-injection methods, and of dynamic capillary pressure measurements made by the Hassler technique. The results indicate a variation from sample to sample of the factor used to convert capillary pressure obtained by mercury injection to those applicable to a water-gas system. Static capillary pressures measured by the restored-state method were found to be in close agreement with dynamic capillary pressures, indicating that data obtained from static measurements may be utilized with confidenre in the solution of dynamic problems of fluid flow. Experimental data are presented on the use of "J-curves" for the correlation of capillary pressure-saturation relations for a number of cores from a particular geologic formation. It is shown that the correlation was improved in some cases by reqtricting it to rertain lithologic classifications. INTRODUCTION The Meaning and Importance of Capillary Pressure The coexistence of two or more immiscible fluids within the voids of a porous medium, such as reservoir rock, gives rise to capillary forces. Because of the interfacial tension existing at the boundary between two immiscible fluids in a pore space, the interface is curved, and there is a pressure difference across the interface. This pressure difference is termed the capillary pressure. The magnitude of the capillary pressure between two immiscible fluids which together fill a porous medium depends upon several factors: the textural properties of the medium, the wettability of the medium, the interfacial tension between the fluids, the respective saturations of the fluids, and the manner in which these saturations are attained. For a given pair of immiscible fluids in a particular sample of reservoir rock, the capillary pressure is a unique function of the fluid saturation, provided that the saturation of the fluid which wets the rock has previously been decreased unidirectionally from an initially complete saturation. Similarly, for a given pair of fluids at a particular saturation which has been achieved by a

Jan 1, 1951

By Harry A. Lipsitt, Rollins E. Hook, Attwell M. Adair

A necessary condition for a uniaxial stress distribution in compression testing is that the specimen end surfaces make full contact with the apparatus compression plates. In addition all compression surfaces must be machined perpendicularly to the loading axis. In general this condition is not sufficiently fulfilled in a simple apparatus. Therefore on application of the load the compression plate may first touch the specimen at one point only. This may cause crumbling of the specimen if the material under investigation is brittle (e.g., ionic crystals). It also precludes a precise study of the beginning of deformation as the effective cross sectional area is unknown. In addition a complex stress state is set up which renders quantitative work impossible, e.g., on dislocation density and arrangement as a function of stress. To overcome these difficulties a "self-adjusting" upper compression plate is required. A simple and reliable method of achieving this is shown in Fig. 1: A steel hemisphere is placed on the specimen. As soon as the compression plate (which no longer needs precise machining) makes contact with this hemisphere the load is uniformly distributed over the whole specimen surface, and a homogeneous uniaxial state of stress results. An advantage of the method is that the loading is always central, even when the specimen surface is not parallel to the compression plate (Fig. 1, dashed line). Therefore to a first approximation a uniaxial state of stress is maintained if the misorientation of the specimen end surface is small. Two typical stress strain curves of identically prepared sodium chloride crystals are shown in Fig. 2; curve 1 was taken without and curve II with the hemisphere under otherwise identical conditions. The improvement in the accuracy of defining the beginning of elastic and plastic deformation is clearly indicated. The writer wishes to thank the Deutsche Forschungsgemeinschaft for financial support, and Professor P. Haasen for providing facilities for this work.

Jan 1, 1962

By Charles Parmelee

When Professor Silliman made his first examination of the newly-discovered Pennsylvania rock oil in 1859, he noted that different rates of heating produced different results in fractionation—longer heating produced larger percentages of light fractions. In 1862, it was found that when petroleum vapors are condensed in the still crown and dropped back into the hot liquid, the result of the distilling operation is materially modified. These early dates mark the beginning of what is called cracking petroleum and is explained as separating the component parts of the hydrocarbon molecules into more and smaller groups of the same elements. The phenomena were utilized for the next 30 years to increase the yield of burning oil. The procedure was that regularly practiced today in dry or destructive distillation. Considerable scientific study was given to the subject from 1862 to 1905, and a number of patents were obtained, but the work done was not continuous or intensive until about 1905, when the increasing demand for gasoline attracted attention of petroleum refiners to the possibilities of cracking. The first equipment built and operated essentially for cracking petroleum on a large scale was placed in successful operation in 1912. The commercial practice is, therefore, less than 15 years old. Comprehensive intense study of the controlling factors during this period has resulted in rapid increase in our knowledge, and material improvement has been made in the practice of the art. It is the purpose of this paper to outline briefly the state of our knowledge and to suggest some of the questions which are attracting attention of researchers at the present time. The major purposes for which petroleum hydrocarbons, including natural gas, are or have been cracked are: 1. To obtain products used to increase the heat value and illuminant content of artificial gas. 2. During the World War, to increase the supply of toluol. 3. To increase the amount of products capable of conversion into industrial chemicals. 4. To produce pure carbon.

Jan 1, 1927