Search Documents

By T. H. Weldon, L. V. Whiton, R. R. McNaughton, J. H. Hargrave

Oxygen enriched air is being used quite extensively in the metallurgical plants of The Consolidated Mining and Smelting Co. of Canada, Limited, at Trail, B.C. The oxygen used for this purpose is a by-product from the Company's chemical plants located in the area. Most of the ore treated in the Trail metallurgical plants comes from Com-inco's Sullivan Mine at Kimberley, B.C. At Kimberley the ore is milled to produce lead and zinc concentrates which are shipped to Trail for further treatment to metal. One section of this paper deals with the use of oxygen enriched air in the suspension roasting of the zinc concentrates. In this process the concentrate is calcined for leaching preparatory to electrolytic recovery of the zinc. A second section of the paper describes the use of oxygen enriched air in operations at the lead smelter. There oxygen enriched air is used in the blast to the lead blast furnaces and in the slag fuming furnace which recovers the lead and zinc contained in lead blast furnace slag. The final section of the paper outlines the precautions necessary for the safe use of oxygen enriched air in any plant operation. The Use of Oxygen Enriched Air in the Suspension Zinc Roasters The suspension roasting of zinc concentrate developed at Trail, B.C., has been described in AIME Vol. 121, "The Electrolytic Zinc Plant of The Consolidated Mining and Smelting Company of Canada, Limited" by B. A. Stimmel, W. 11. Hannay and K. D. McBean. Since the publication of that paper, the use of oxygen enriched air in suspension roasting has been introduced as regular practice with marked advantage. The relative importance of a specific advantage may vary with changing conditions, but, in general, it may be stated that improved operation has been achieved at increased capacities. Suspension roasting is carried out at Trail in converted standard 25 ft diam Wedge roasters. The 2nd, 3rd, 4th and 5th roasting hearths have been removed and the drying hearth covered over. Drying of the concentrate is done on the drying hearth and the 1st roasting hearth. The dried concentrate, after any lump's have been broken up in a ball mill, is fed to a single burner located in the upper part of the combustion chamber. Oxygen is introduced at the burner fan along with the gases from drying, returned combustion gases from the waste heat boiler outlet and the required amount of new air. Up to 60 pct of the concentrate settles out on the 6th roasting hearth, the rest passilig out of the roaster. The product collected in the waste heat boiler is finished calcine, but the dust collected in the cyclones after the boilers is returned to the base of the combustion chamber where the sulphate is decomposed. Gases from the c'yclones go to a Cottrell precipitator. The discharges from the 7th roasting hearth and the waste heat boiler are combined with the Cottrell dust to give the finished calcine. Following small scale tests started in 1933, oxygen enriched air has been used continuously in the suspension roasting of zinc concentrate in Trail, beginning in 1937. A significant factor in promoting its use in this operation was the availability of by-product oxygen from the Company's near-by Chemical and Fertilizer Division. To-day it is standard practice at Trail to use oxygen enriched air for zinc concentrate roasting. The most important requirement in roasting a zinc concentrate for an electrolytic plant is that the zinc in the calcine should have maximum solubility. It is also desirable at Trail that the gas produced for the manufacture of suhhuric acid should have a ~naximum concentration of SO2 and that a substantial recovery of waste heat from the gas be achieved. High solubility of zinc requires that the sulphide sulphur and zinc ferrite in the calcine be kept low. These are both functions of temperature and time, with formation of zinc ferrite also dependent on contact between the iron and zinc particles. One of the inherent advantages of suspension roasting is that minimum time and contact are achieved. The limit on temperature is imposed by the fusion point of the concentrate and not by the need to control zinc ferrite formation. Operating temperatures are normally maintained within the limits of 1725" and 1850°F. A relatively low zinc sulphate in the calcine is required at Trail, and this results from discharging the calcine from the high sulphur dioxide atmosphere at a temperature above 1600°F.

Jan 1, 1950

By Robert E. Palmer

The Hawkesworth detachable drill steel shank and bit were invented by A. L. Hawkesworth, while he was a mechanical foreman for the Anaconda Copper Mining Co., at Butte, Mont. Mr. Hawkesworth died on June 16, 1925, at the time that his invention was practically a proved success. The first application for patents was made by him in November, 1918, and the bit is now being manufactured under patents issued in 1922 and 1923. The credit for its development in the early stages belongs to A. L. Hawkesworth, Roy S. Alley, Harry A. Gallwey, E. J. Bowman and various officials of the Anaconda Copper Mining Co. Later improvements, manufacturing problems and the direct usage in the mines were originated and perfected by the mechanical department under C. D. Woodward, E. R. Borcherdt, head of the Rock Drill Equipment Department, Robert E. Kelly of the Mechanical Department, and various operating department heads of the Anaconda Copper Mining Co. The author wishes to acknowledge the assistance of these officials in the preparation of this paper. Comparison of Costs Using Regular Drill Steel and Detachable Drill Steel In 1922 production was satisfactory and sufficient enough to warrant a complete installation in an operating mine. The study and tests were made at the Badger State mine, the production of which averaged 1200 tons of ore per day. E. R. Borcherdt, head of the rock drill equipment department, was in direct charge of the trials, installation, operating problems and records during the entire .period, arid still continues in that position. This mine is a typical Butte mine, operated through a standard four-compartment shaft, served by a double drum hoist and an auxiliary hoist. The texture of the ground and ore has all the variations from soft to very hard granite and sulfide ore with production from levels between the

Jan 1, 1930

By Frederick Beckett

WIDESPREAD experimentation has been conducted in recent years to devise a means of preventing intergranular corrosion in austenitic chromium-nickel steels of the 18 per cent chromium-8 per cent nickel type. Additions of titanium to these steels have been used commercially to overcome this difficulty, as advocated by Krupp of Germany, and the latest literature reference concerning improved details of this method is the article by Bain, Aborn and Rutherford.1 Extensive work by the present authors has shown columbium also to be a particularly valuable agent for inhibiting intergranular corrosion. This paper does not deal with steels that are largely or wholly aus-tenitic ; it is limited to a discussion of the results obtained through the use of titanium and columbium in plain high-chromium steels. For many years titanium has been used commercially by some steelmakers as a cleanser, and to a lesser extent as a hardener, but then in greater per-centages. The results of the work to be described disclose that titanium and columbium in proper proportions act as effective softeners in the high-chromium steels. It is well known that chromium intensifies the hardening effect of carbon in steel; it imparts pronounced air-hardening properties within a rather wide range of chromium content; it provides increased ductility in steels of given strength and hardness; and it enhances resistance to corrosion and oxidation at elevated temperatures to a marked degree. However, in applications requiring a combination of some of these valu-able properties great hardness is frequently a detriment rather than a merit. When the objective is a soft and ductile steel having optimum corrosion resistance, the producer strives for a carbon content as low as commercially practicable.

Jan 1, 1933

By Robert Schorr

A Discussion of the Paper by Robert Schorr, read at the Atlantic City meeting, February, 1904. (Washington Meeting, May, 1905.) E. T. DUMBLE, Houston, Texas (communication to the Secretary*) :-In addition to the list of publications mentioned by Mr. Schorr and those by Prof. Hofman, I call attention to the following references : Studi sulle Lignite, by Capacci. Turin (1890). (An excellent work.) Report of Brown Coal Industry in Germany. J. Cosmo Newberry. Department of Mines, Victoria (1892). Second Report of the Royal Commission. on Coal Supply. Vol. II. London (1904). Peat Fuel: Its Manufacture and Use. Report of the Bureau of Mines of Ontario, 1903. Mr. Schorr says : " Brown coal and peat are briquetted as a rule without binder," but this statement is entirely true only so far as raw peat is concerned, and it is but partly true of brown coal. With regard to raw peat, briquetting without bond is carried on successfully both in Europe and America, and the development of the industry in Canada is fully described in the Bureau of Mines report for 1903, mentioned above. While there is still room for improvement in the efficiency of some of the arrangements for drying the peat previous to briquetting, a very satisfactory fuel is made at a price which enables it to compete with coal. During the late strike in the anthracite regions of Pennsylvania, the manufacture of peat: briquettes received a considerable impetus, and possibly the attention directed to it on this account may result in a. considerable increase in the output. In Canada. the peat when it is first excavated from the ground

Mar 1, 1905

By H. E. Dunn, C. M. Cosman, J. H. Brennan

Up to the beginning of World War I, the American ferro-alloy industry was in its infancy and largely dependent on Europe. During that War, capacity was over expanded. Later recovery and commercial and scientific development have resulted in an industry which in 1957 produced 1.8 million tons of ferro-alloys. THE ferro-alloy industry is today an important element of the industrial structure of the United States. Its output is valued at almost half a billion dollars annually and its products are basic not only to National defense but also to the peacetime standard of living. This has not always been so. The ferro-alloy industry from late in the last century has grown from small beginnings, nurtured by the demand for stronger, tougher materials; by the search for steels capable of absorbing severe impact loads and resisting corrosive media and high temperatures; and also by the need for electrical and electronic specialties. Conversely, the ferro-alloy industry has grown because it developed improved steels and alloys by extensive research, and because it was able to show to steel makers the advantages accruing from the more extensive and the more economical use of alloying elements. The industry has grown in scope from producing a few grades of ferro-alloys of the more common metals-manganese, chromium, vanadium, silicon, titanium, tungsten, and molybdenum-until there are today some 150 compositions of ferro-alloys available to the steel maker, including such elements as columbium, zirconium, and boron. In 1912 the industry produced 360,000 tons of alloys valued at about $12,000,000, while 1957 production figures show an output of 1.8 million tons worth $440,000,000. In the United States, the history of an industry is largely the history of the companies making up this industry; hence, this paper will briefly trace the development of the most important ferro-alloy-producing companies. Quite varied have been the reasons that caused the different companies to move into the ferro-alloy field; the Willson Aluminum Co., seeking methods of producing aluminum, succeeded with the production of calcium carbide, and their developing electric furnace skills led them to the production of ferro-silicon and ferrochromium alloys. Willson was the predecessor of the Electro Metallurgical Co. of Union Carbide. Two Pittsburgh undertakers, interested in vanadium as an alloying agent for steel, set about to find a mine and, ranging as far as Peru, fathered American Vanadium Co., the predecessor of Vanadium Corp. of America Experiments of the

Jan 1, 1961

By L. K. Oliver, Marshall

The use of model studies for the development of invasion patterns for cycling is .illustrated by model studies obtained with a recently developed apparatus in the solution of actual cycling problems. Introduction Depletion of a gas reservoir by cycling under pressure maintenance may be divided into three general phases. In the first phase, injection of dry gas is used to move all possible wet gas to producing wells prior to breakthrough of appreciable quantities of dry gas into producing wells. In the second phase, injection moves additional wet gas to producing wells while moderate quantities of dry gas are being produced. The third phase consists of production without injection to deplete the commercial gas reserve which remains after the cycling operation. Thus, in the first phase, a portion of the reservoir is invaded by dry gas, and the dry gas usually displaces something less than 100 pct of the wet gas from the invaded portions of the reservoir. The second phase enlarges the invaded portion of the reservoir and, at the same time, increases recovery from that zone invaded by dry gas in the first phase of the cycling operation. The result is an early yield of a substantial quantity of the liquefiable hydrocarbons in the reservoir with a minimum of the retrograde losses which occur in some reservoirs. The overall recovery from such an operation is usually high. The summation of the paths taken by dry gas in a cycling operation can be termed an invasion pattern. The use of electrical models to predict invasion patterns has been the subject of several contributions to the literature.1-3 The results of such model studies as applied to actual cases has been discussed by Kelton4 and Miller and Lents.= Recently, an improved apparatus for conducting potentiometric model studies has been developed, as described by Lee.V he purpose of this paper is to present model studies or invasion patterns obtained with this instrument in the solution of actual cycling problems. The percentage of displacement of wet gas within the invaded portion of the reservoir in cycling, increase in recoveries of wet gas by continuing cycling after dry gas breakthrough, recoveries of wet and dry gas by production after cycling, or economic factors in cycling are beyond the scope of this paper. Discussions which follow will be limited entirely to the development of suitable invasion patterns for cycling under pressure maintenance and the use of model studies therein. Discussion OF Results In using model studies to predict invasion patterns in cycling, some factors which influence the results are the following:

Jan 1, 1948

By Marshall, L. K. Oliver

The use of model studies for the development of invasion patterns for cycling is .illustrated by model studies obtained with a recently developed apparatus in the solution of actual cycling problems. Introduction Depletion of a gas reservoir by cycling under pressure maintenance may be divided into three general phases. In the first phase, injection of dry gas is used to move all possible wet gas to producing wells prior to breakthrough of appreciable quantities of dry gas into producing wells. In the second phase, injection moves additional wet gas to producing wells while moderate quantities of dry gas are being produced. The third phase consists of production without injection to deplete the commercial gas reserve which remains after the cycling operation. Thus, in the first phase, a portion of the reservoir is invaded by dry gas, and the dry gas usually displaces something less than 100 pct of the wet gas from the invaded portions of the reservoir. The second phase enlarges the invaded portion of the reservoir and, at the same time, increases recovery from that zone invaded by dry gas in the first phase of the cycling operation. The result is an early yield of a substantial quantity of the liquefiable hydrocarbons in the reservoir with a minimum of the retrograde losses which occur in some reservoirs. The overall recovery from such an operation is usually high. The summation of the paths taken by dry gas in a cycling operation can be termed an invasion pattern. The use of electrical models to predict invasion patterns has been the subject of several contributions to the literature.1-3 The results of such model studies as applied to actual cases has been discussed by Kelton4 and Miller and Lents.= Recently, an improved apparatus for conducting potentiometric model studies has been developed, as described by Lee.V he purpose of this paper is to present model studies or invasion patterns obtained with this instrument in the solution of actual cycling problems. The percentage of displacement of wet gas within the invaded portion of the reservoir in cycling, increase in recoveries of wet gas by continuing cycling after dry gas breakthrough, recoveries of wet and dry gas by production after cycling, or economic factors in cycling are beyond the scope of this paper. Discussions which follow will be limited entirely to the development of suitable invasion patterns for cycling under pressure maintenance and the use of model studies therein. Discussion OF Results In using model studies to predict invasion patterns in cycling, some factors which influence the results are the following:

Jan 1, 1948

By Thomas R. Stauffer

The principle that conventional schemes for taxing petroleum or mineral resources are "inefficient" is illustrated using simulation calculations tested against an "ideal" system. Inefficiency is defined as the relative success in maximizing expected government revenues from the resources. Most systems fail because: 1) they leave oil in limbo, i.e. unproduced because of excessive fiscal burden; or 2) they unnecessarily increase the variance in the explorationist'c, rate of return by undertaxing large fields and overtaxing smaller but infra-marginal fields. This increases his discount rate and reduces taxable surplus. An "ideal" tax system is specified which maximizes government revenues while minimizing risk to the operator. Two criteria are developed: 1) the tax falls to zero on fields which yield only the minimum necessary rate of return ("marginal" fields); and 2) the after-tax present value of all fields is the same for all fields above a threshhold size. In particular, marginal fields, while contrib- uting little to expected values, do contribute to reducing variance and hence risk praemia by distributing the exploration costs over a higher probability of successful outcomes.

Jan 1, 1982

By Clarence Claghorn

ONE of the simplest and most easily effected steps toward mechanization and concentrated mining in coal mines is the substitution of transport or room conveyors for the customary tracks in rooms, thus bringing the coal to the cars instead of taking the cars to the coal. As this involves little or no change in the established room and pillar layout, it appeals to the conservative operator who is more or less fearful of changes in system involving the element of roof con-trol. An increasing number of these room conveyors would seem to attest the favorable commercial results secured. Rooms are naturally driven as wide as roof conditions permit, providing maximum tonnage from each room cut. If the rooms are more than 12 to 14 ft. in width the room conveyor is usually set along one rib, a porta-ble face conveyor being set along the face itself and within easy shoveling distance of it, so arranged as to discharge to the transport conveyor. As the room ad-vances the latter is lengthened and the face conveyor moved up laterally. The advantages of this layout are, briefly, low lifts, no shoveling, no waiting for cars. It gives easy shovel-ing conditions and continuous production so long as there is loose coal at the face. Several loaders are usually employed at the face and the room is loaded out several times each shift. In fact, where the rooms are fairly wide, by judicious management, cutting and load-ing may go on simultaneously. Under these conditions, naturally, the face conveyor plays an important part as it is the appliance on which the coal is actually loaded. Someone has aptly stated that the loading is a question of "foot pounds," which is an appealing way to put it, for it is the number of pounds to be moved by the number of feet which measures the work to be done. It can easily be seen that the design of the face con-veyor is a matter of importance. It might be an im-perfect target for the shovel or of an awkward shape and height, and so involve extra effort on the part of the loader, tiring him when kept up continuously and at the same time slowing up his shoveling speed.

Jan 12, 1927

By R. A. Wood, R. I. Jaffee, H. R. Ogden, D. N. Williams

The tensile properties, creep resistance. and thermal stability of highly alloyed Ti-Al-Zr alloys were examined. On the basis of these studies, the Ti-7Al-1ZZr composition was selected for more complete evaluation. The alloy was found to be weldable and free from excessive directionality. In addition, it developed maximum properties without requiring heat treatment other than an annealing operation in the alpha field. The alloy was recommended for scale up and is presently being investigated on a production-level basis. One of the more attractive properties of titanium alloys is their ability to withstand stress at moderately high temperatures, and a considerable amount of effort has been devoted to increasing the maximum service temperature of titanium alloys. This work has suggested that the optimum alloys for high-temperature service will be single-phase a (close-packed hexagonal) alloys containing significant amounts of aluminum. However, the maximum amount of aluminum which can be alloyed with titanium is between 6 and 8 pct,l since at high-aluminum contents an embrittlement reaction occurs in the anticipated service temperature range, 800" to 1100°F. It has been shown that the embrittlement reaction involves decomposition of the high-aluminum a phase to one or more new phases.' Since this reaction does not occur at intermediate or low-aluminum contents, it was felt that intermediate Ti-A1 alloys might be strengthened by a-soluble ternary additions without inducing the embrittlement reaction. The first alloying addition considered was tin, which shows extensive solubility in a titanium and has moderate strengthening tendencies. Unfortunately, it was soon apparent that tin also promoted the embrittlement reaction, and that to obtain a stable alloy, the aluminum content had to be reduced as the tin content was increased. The second alloying addition considered was zirconium, which is similar to tin in its effects on titanium. This element did not contribute to the embrittlement reaction and, in fact, appeared to increase the maximum amount of aluminum which could be alloyed with titanium without inducing instability. This paper describes an investigation of the Ti-A1-Zr a alloy region. Alloys containing from 4 to 12 pct A1 and from 6 to 15 pct Zr were examined. The properties of these alloys are described and the bases for selecting an optimum composition is outlined. This composition, Ti-7A1-12Zr, is presently being scaled up in tonnage quantities, and is being evaluated extensively throughout the industry. In addition to presenting the basis for its selection, this paper presents a description of the properties developed in laboratory material as determined during the alloy investigation. These properties suggest that this alloy can fill an important position in applications requiring light weight, fabrica-bility, weldability, and strength to 1000oF or higher. EXPERIMENTAL PROCEDURES Titanium alloy ingots were prepared by inert electrode arc melting under an argon atmosphere. Alloying elements used were 110 Bhn titanium sponge, high-purity aluminum, and reactor-grade zirconium. Pancake-shaped ingots were prepared weighing approximately 300 g. The composition of the ingots was checked by weight measurements before and after melting. The pancake ingots were forged at 2000°F to approximately half their original thickness to give a flat plate roughly 1/2 in. thick. This plate was then rolled at 1800' to 1600°F to 0.250 in. thick. All of the alloys examined fabricated well. However, alloys containing 15 pct Zr tended to overheat due to exothermic oxidation, and scaling was excessive. As might be anticipated from its effect in decreasing the ß transus, increased zirconium appeared to improve fabricability somewhat, especially during rolling at lower temperatures. Except for a limited study of heat-treatment response, all alloys were examined in the a-annealed condition. Prior to heat treatment the a and ß tran-sus temperatures were determined by metallo-graphic examination of samples quenched after annealing at 50-deg intervals in the transformation region. These data are shown in Fig. 1. Recrystal-lization appeared to occur in about 1 hr in the range 1300º to 1500ºF. Therefore, alloys were annealed for 1 hr at 1550ºF (4 and 5 pct Al), 1600ºF (6 through 7-1/2 pct Al), or 1650°F (8 or more pct Al). This produced an equiaxed a grain structure. In most alloys, a "ghost" structure was visible after the a-annealing treatment, as shown in Fig. 2. This structure apparently resulted from the acicular

Jan 1, 1963

By D. S. Rowley, F. C. Appl

Assuming that rock behavior, during cutting with a single diamond, may be approximated by that of a rigid, Coulomb, plastic material, a theory of single diamond cutting action has been developed. Using this theory, the stresses on the diamond cutting surface and the components of the cutting force have been determined. Theoretical results agree reasonably well with available experimental data. The theory of cutting of single diamonds may be used as the basis for subsequent study of the perfonnance of surface set diamond drill bits and other surface set diamond cutting tools. INTRODUCTION For more than twenty years, surface set diamond bits have been used successfully in the mining and petroleum industries to drill and core rock formations that range from medium hard to the hardest known formations. Most extremely hard rock formations cannot be economically drilled or cored by any other means. In view of the growing use and importance of surface set diamond drill bits, it is reasonable to study the way in which these tools cut, and the factors that influence wear of the diamonds. Such knowledge will contribute to better bit design and will improve operating procedures. To analyze the cutting performance of these tools it is appropriate to consider the way in which an individual diamond cuts. Once this is established, the over-all performance of the bits can be determined by considering the total effect of the individual diamonds. In recent years there has been a growing interest in rock mechanics and there now exist several publications dealing with the deformation and failure of rocks. Notable experimental work has been reported by Bredthauer,1 Handin and Hager,2, 3 and Gnirk and Cheatham.4 An extensive collection of data pertaining to rock properties at low confining pressures has been given by Wuerker.5 Cheatham and Gnirk have recently presented an excellent review of the state of knowledge regarding analytical and experimental rock deformation and failure.6 Generally rocks are extremely weak in uniaxial tension, and weak or only moderately strong in uniaxial compression. Both tensile failure and compressive failure are generally brittle in nature. This means that there is little or no deformation or "flow" of the material before shear or tensile fracture occurs. Thus, until fracture occurs, rock behaves very nearly like an elastic material in uniaxial stress. Significant changes in behavior of rock occur under conditions of triaxial compressive stress. There is generally a marked increase in compressive strength and in ductility. It has been demonstrated that the failure becomes plastic (in a macroscopic sense) at sufficiently high values of confining pressure. Sharp wedge chisel indentation studies conducted by Gnirk and Cheatham indicate that many rocks behave in a plastic manner at relatively low triaxial compressive stress states.4 If "failure" under triaxial compressive conditions is considered to be either complete rupture or macroscopic plastic flow, then the general failure characteristics of a rock can be reasonably well represented by the commonly known Mohr envelope. This certainly is not a perfect failure criterion (since the effect of the intermediate principal stress is neglected) but it has been found to be adequate for most engineering purposes. Mohr envelopes usually are constructed graphically using experimental triaxial test data. For purposes of analysis it is convenient to represent the envelope in equation form. Among the several approximate forms appearing in the literature, a parabolic form is suggested by Cheatham,7 and an exponential form is suggested by Paone and Tandanand.8 The exponential form has been adopted for this study, and based on published data, appropriate parameters have been established for 19 rock types. A typical plot of the data compared with the approximate envelope, and a summary of the rock properties and

Jan 1, 1969

By AIME AIME

THE report of the united. States Steel Corporation for the' year 1928 gives the, following ,figures of raw materials and' finished products . Raw materials, tons :

Jan 1, 1929

By C. C. Harris

The characteristics of some common size distribution equations are critically discussed. A generalized form of several well-known size distribution equations is obtained from a differential equation describing statistical distributions. The equation contains three parameters and can describe the major features of size distributions in the fine and the coarse size regions. A graphical method for its implementation is provided. The application of this and other equations to sets of data are compared both for the quality of fit and from a comminution kinetics viewpoint. If a narrow size range of a brittle material is broken sufficiently to obliterate the feed sizes, but not so severely that excessive secondary breakage occurs, a plot of cumulative fraction by weight undersize (Y) vs. sieve size (X) on a log log grid (sometimes called the Gates-Gaudin-Schuhmann plot)1-3 gives a straight line of slope ~ 1 over much of its range. On closer inspection, deviations in the extreme coarse range covering perhaps 10 to 30% of the total sample may be apparent (frequently, a change in slope from ~ 1 to a value different from unity) together with over-all slight irregular departures from a smooth line. One model of breakage postulates that the same fracture pattern persists throughout all size ranges.4 The fracture pattern is characterized by the slope of the line on a log log grid. Accordingly, a distribution of sizes broken in the manner specified earlier is expected to produce a size distribution having the same slope as that of a broken narrow size range. Additionally, the slight irregularities mentioned above should even out in the summation process, giving a smooth straight line of slope ~1 on a log log plot. This idealized state of affairs does not, however, describe the distribution of a multi-event process such as that for a tumbling mill product. On the average, these curves (plotted again log log) tend to have a slope in the fine region different from and usually less than unity,5 while the coarse size region curves with increasing slope for cases of mild reduction, and with decreasing slope when moderate or severe size reduction has occurred. In addition, there are usually slight irregular deviations from a smooth curve. Most curves display two distinct regions — fine and coarse — and a few curves show one or more intermediate regions. Feed size studies6,7 show an effect which theory is required to explain. For the same material, mill loading and other operating conditions, and the same time of grinding, plotting the dimensionless ratios Y vs. X/(feed size) does not reduce the size distribution data to the same curve. Y vs. X does not correlate the coarse region, but it can provide a crude correlation of the fine region which improves as size diminishes and as grinding time increases. The size distribution in the coarse region is somewhat more dependent on the feed size than is the distribution in the fine region wherein the degree of dependence diminishes as time proceeds; the distribution of sizes in the fine region are determined largely by the nature of the material and the comminution conditions. A comprehensive model of comminution must recognize that several different patterns or modes of breakage can occur in a mill; 5,8,9 that there can be some selection in that some size ranges are broken more than others; and that, while some particles may be the product of a single fracture event, or may even remain unbroken, others result from multiple rebreak-age. Thus, breakage in a tumbling mill is more complex than the Schuhmann4 model admits in that several different types of comminution micro-events* occur rather than just one type, and these events, though different in size scale, are of the same overall pattern as that which is visualized by the model. The concept of an average comminution micro-event has, therefore, a mathematical rather than a physical connotation, at least for tumbling milling. Equations with which to describe particle size distributions have been sought for over half a century.10-13 No equation presently in general use was first derived from an analysis of the statistical mechanics of breakage; whatever theoretical basis the existing

Jan 1, 1969

By M. R. Geer Olds, H. F. Yancey

THE increase in the number of coal-cleaning plants employing dense-medium processes occurring since 1946 is especially interesting when viewed historically. Both sand and magnetite were introduced as material for heavy mediums at about the same time, sand in the Chance process in 1921 and magnetite in the Conklin process in 1922, but from that point on their records diverge. The Chance process enjoyed a steady growth from its inception, whereas no additional magnetite plants were built in the United States for over 20 years. Then, following the close of the World War 11, magnetite was again introduced, this time with marked success. During the following years some 47 plants employing magnetite medium were built. This rapid growth of dense-medium cleaning has been concurrent with widespread adoption of full-seam mining on one hand and a return to a more competitive market on the other. At a time when changing mining practice has provided cleaning plants with dirtier coal and changing market conditions have simultaneously demanded a cleaner product, the industry has through necessity turned to improved preparation. The inherently greater sharpness with which dense-medium processes can separate coal from impurity is thus helping to hold the line against ever-increasing mining costs and at the same time assisting materially in retaining badly needed markets. Although dense-medium cleaning unquestionably offers a distinct advantage when the washing problem is difficult, other methods can provide almost equally high efficiency when the coal is easy to wash. Moreover, fine coal cannot yet be treated by heavy medium in a proved process, although the Driessen cyclone is in the pilot-plant stage. Most of the present types of dense-medium equipment have been in use only a few years, and the dearth of information in the literature concerning their performance characteristics is entirely understandable, Nevertheless this information is necessary if the process is to be intelligently applied to individual cleaning problems. Without data on the efficiency of a process in a particular type of separation, it is difficult to assess the advantage to be expected from it. Similarly, the role of particle size in heavy-medium separation is important in some cases, yet there is little published information on this aspect. To mention only one more of the numerous points on which essential information is lacking, the bearing of medium characteristics on performance has been discussed only in qualitative terms. It was with the hope of providing information on some of these points that the Bureau of Mines built a dense-medium pilot plant for cleaning coal at its Northwest Experiment Station in Seattle in 1950. The plant has been operated continuously since that time, and over 50 runs have been made on 7 coals exhibiting a wide range of washability characteristics. An idea of the magnitude of this work will be gained from the fact that examination of the plant products has involved some 600 float-and-sink separations and about 2500 ash determinations. A laboratory pilot plant is especially well adapted to investigate many aspects of performance because close control over test conditions can be exercised and because a large number of tests can be made rapidly. On the other hand, factors such as consumption of medium and other cost items can be investigated satisfactorily only in a commercial plant. Actually, the two forms of investigation should be complementary, with the laboratory work pointing the way for confirming tests in commercial units. Pilot Plant The dense-medium pilot plant employed for this work comprises a 24x30-in. drum-type separating vessel, a 12-in. densifier, a 12-in. magnetic separator, a 26-in. x 9-ft vibrating screen, and the necessary pumps and conveyors for handling materials. Arrangement of these units corresponds with the flowsheet used in most commercial plants, except that a thickener is not provided for the feed to the magnetic separator. Coal and refuse discharge from the separating drum to the vibrator, which is divided longitudinally down the center. Medium draining through the first 3 ft of the screen is recirculated directly to the drum. Sprays on the middle 3 ft of the screen rinse medium from the products, and the last 3-ft section is for dewatering. Dilute medium from the rinsing and dewatering sections is pumped to the magnetic separator, where magnetic solids are recovered. These are pumped to the densifier, from which they return to the medium-drainage sump by gravity through a demagnetizing coil. The drum-type separating vessel is a scale model of a commercial unit. Feed enters axially at one end of the drum just below the surface of the bath, and float material overflows through a circular opening at the other end. Particles sinking to the bottom of the bath are picked up by lifting flights bolted to the inner wall of the drum, elevated out of the bath, and sluiced to the vibrating screen. Baffles suspended in the bath prevent float material from entering the sink-lifting flights. About 8 gpm of medium is used to sluice the feed into the drum. An additional 15 to 24 gpm, depending upon operating conditions, is added through two pipes dipping into the bath behind the baffle on the side where the sink-lifting flights enter the bath. The bath available for separation is 2 ft long and 13 in. wide, giving an area of 2.08 sq ft. Depth of bath from the surface to the top of the sink-lifting flights, measured vertically below the axis, is 6 in.

Jan 1, 1954

By R. J. Pfister

The development of a water-input profile instrument based on the introduction of brine and fresh water into an input well with the electrical location of, the boundary developed between them is reported. Two methods are available in the use of this instrument to measure the foot by foot water-intake rates of the various sand strata: the moving boundary method in which variable well bore diameters can be determined and/or cancelled out and the constant boundary method. The type of results obtained and the relative advantages of each of these methods are described in detail. Representative data are included covering the use of this instrument in experiments involving selective acidizing, selective plugging, and selective shooting. In such experiments, this instrument has been used to diagnose the unfavorable distribution of water intake in input wells and also to determine the effectiveness of the resultant treatments. The data included also serve to illustrate the type of problems which can be studied with this technique. Introduction For ten years or perhaps longer a number of progressive water-flood operators have felt the need for some to to measure the foot by foot water-intake rates of various strata in water-injection wells. The primary need is to diagnose unfavorable water distribution in various strata and to evaluate the effectiveness of the corrective measures such as selective acidizing, selective plugging, and selective shooting. Previously described methods for obtaining this type of data were not considered entirely adequate.l,2 The profile equipment described in this paper embodies the separate introduction of brine and fresh water into the well at carefully measured and controlled rates and the electrical location of a sharp boundary developed between these fluids. At present this instrument is a research tool of value in determining the effect of various well treatments on an individual sand strata. lts primary use has been on wells in which different sections require different treatments (e.g., wells with an open sand to be plugged and a tight sand to be acidized)- It has, thus, made possible the determination of a rearrangement of the water intake of a well. The instrument can also be used to direct the treating material into a given zone. In completing a well the less permeable sands are shot more heavily with nitroglycerine in order to equalize the water intake between the permeable and less permeable sands. The extent to which such corrective shooting has been successful Can be determined by a water-input profile. The combined profile and well-bore diameters should also provide a method for determining the direction and effect of various selective shooting techniques. Equipment The essentials of the water-input profile technique for measuring the intake per foot of individual sand strata are the injection of a nonconducting fluid, water, at the top of the well and a conducting fluid, brine, through a separate string of

Jan 1, 1948

By R. J. Pfister

The development of a water-input profile instrument based on the introduction of brine and fresh water into an input well with the electrical location of, the boundary developed between them is reported. Two methods are available in the use of this instrument to measure the foot by foot water-intake rates of the various sand strata: the moving boundary method in which variable well bore diameters can be determined and/or cancelled out and the constant boundary method. The type of results obtained and the relative advantages of each of these methods are described in detail. Representative data are included covering the use of this instrument in experiments involving selective acidizing, selective plugging, and selective shooting. In such experiments, this instrument has been used to diagnose the unfavorable distribution of water intake in input wells and also to determine the effectiveness of the resultant treatments. The data included also serve to illustrate the type of problems which can be studied with this technique. Introduction For ten years or perhaps longer a number of progressive water-flood operators have felt the need for some to to measure the foot by foot water-intake rates of various strata in water-injection wells. The primary need is to diagnose unfavorable water distribution in various strata and to evaluate the effectiveness of the corrective measures such as selective acidizing, selective plugging, and selective shooting. Previously described methods for obtaining this type of data were not considered entirely adequate.l,2 The profile equipment described in this paper embodies the separate introduction of brine and fresh water into the well at carefully measured and controlled rates and the electrical location of a sharp boundary developed between these fluids. At present this instrument is a research tool of value in determining the effect of various well treatments on an individual sand strata. lts primary use has been on wells in which different sections require different treatments (e.g., wells with an open sand to be plugged and a tight sand to be acidized)- It has, thus, made possible the determination of a rearrangement of the water intake of a well. The instrument can also be used to direct the treating material into a given zone. In completing a well the less permeable sands are shot more heavily with nitroglycerine in order to equalize the water intake between the permeable and less permeable sands. The extent to which such corrective shooting has been successful Can be determined by a water-input profile. The combined profile and well-bore diameters should also provide a method for determining the direction and effect of various selective shooting techniques. Equipment The essentials of the water-input profile technique for measuring the intake per foot of individual sand strata are the injection of a nonconducting fluid, water, at the top of the well and a conducting fluid, brine, through a separate string of

Jan 1, 1948

By T. E. Leontis

The specific effect of various rare-earth metals on the room- and elevated-temperature properties of magnesium has been evaluated. Alloys containing didymium exhibit the highest tensile and compressive strengths at room and elevated temperatures. All the rare-earth metals increase the creep resistance of extruded magnesium at temperatures in the range of 400° to 600°F, but the degree of enhancement depends on the temperature and on the concentration of the added metal. THE effects of rare-earth metals on the properties of sand-cast magnesium were discussed in some detail in earlier paper by the author.' The present paper deals with the effect of the same alloying elements on the properties of extruded magnesium. This investigation also had as its aim the development of a wrought alloy having a better combination of room-temperature strength and ductility and elevated-temperature strength and creep resistance than is found in magnesium-Mischmetal-manganese alloys, which have been reported earlier.2-5 The only known attempt to study wrought magnesium alloys containing pure cerium instead of Mischmetal was made by Mellor and Ridley.6 They found that in the form of rolled bars there is a definite, optimum cerium content for creep resistance at 200 °C and that the creep resistance of these alloys at 200 °C is significantly Improved by heat treatment at 550" to 580"C. In the present investigation the compositional variation in mechanical properties of the following alloy systems is presented: I—magnesium-Misch-metal. 2—magnesium-cerium-free Mischmetal. 3— magnesium-didymium. 4—magnesium-cerium. 5— magnesium-lanthanum. Alloys containing predominately praseodymium are not included in this series because of the lack of this material. Experimental Procedures The alloying ingredients used in preparing the alloys described herein are the same as those reported in the earlier paper.' Cerium-free Mischmetal is the rare-earth mixture remaining when the cerium is removed from Mischmetal, which contains all the rare-earth metals as they occur naturally in mon-azite sand, the ore from which Mischmetal is produced. Removal of both cerium and lanthanum from Mischmetal leaves what is commonly called "didym-ium," consisting predominantly of neodymium and praseodymium. Although the composition of the particular batch of each metal used may differ somewhat from the analysis presented previously, these differences are not great enough to warrant repeat- ing the specific composition of each material. The electrolytic magnesium used as the starting material in these alloys has the same typical analysis as that given in the earlier paper.' The alloys were prepared in small laboratory melts applying all the necessary precautions for alloying rare-earth metals with magnesium described by Marande.' Most melts were large enough to cast one 3 in. diam billet 10 in. long. In a few cases, particularly the didymium-containing alloys, the lack of sufficient amounts of the rare-earth metal limited the size of the billet to 6 to 8 in. All billets were scalped to a diameter of 2 15/16 in. and faced to a length of 9 ¼ in. as limited by the size of the extrusion container. The alloys were extruded into ½ in. diam rod on a 500-ton direct-extrusion press using a 3 in. container. The details of the extrusion step are: billet preheat, 925°F (2 hr); container temperature, 900°F; die temperature, 900°F; extrusion speed, 10 ft per min; reduction ratio, 36:1; and percent reduction, 97.3. The lower melting point of alloys containing didymium' necessitated reduction of the extrusion speed to 5 ft per min in order to prevent hot shorting during extrusion. Adequate lengths were cropped from both ends of each extruded rod to assure that all the material used for tests was extruded under uniform conditions. Tensile and compressive properties at room temperature are reported in the several conditions of heat treatment. The ASTM designations are used to distinguish these conditions as follows: T5—Direct age at 400°F (16 hr) T4—Heat treat at 950°F (4 hr) for alloys containing didymium T4—Heat treat at 1050°F (4 hr) for all other alloys T6—T4 + age at 400 °F (16 hr) The lower heat-treating temperature for alloys containing didymium is necessitated by the lower melting point of these alloys. All heat treatments were conducted in electrically heated, circulating-air furnaces. A protective atmosphere containing 0.5 to 1.0 pct sulphur dioxide was used for the high temperature heat treatments. Tension and creep specimens 6 Yz in. long and compression specimens 1½ in. long were cut from the extruded rod. A reduced section of ? in. diam was machined on the tension specimens, whereas on the creep specimens a reduced section of 0.450 in. diam

Jan 1, 1952

By H. R. Thresh

An oscillational vis cometer has been constructed to measure the viscosity of liquid metals and alloys to 800°C. An enclosed cylindrical interface surrounds the molten sample avoiding the free surface condition found in many previous measurements. Standardization of the apparatus with mercury has verified the use of Roscoe's formula in the calculation of the viscosity. Operation of the apparatus at higher temperatures was also checked using molten lead. Extensive measurements on five different samples of zinc, of not less than 99.99 pct purity, indicate i) impurities at this level do not influence the viscosity and ii) the apparatus is capable of giving reproducible data. The variation of the viscosity ? with absolute temperature T is adequately expressed by Andrade's exponential relationship ?V1/3 = AeC/VT , where A and C are constants and V is the specific volume of the liquid. The values of A and C are given as 2.485 x 10-3 and 20.78, 2.444 x 10-3 and 88.79, and 2.169 x 10-3 and 239.8, respectively, for mercury, lead, and zinc. The error of measurement is assessed to be about 1 pct. Prefreezing phenomena in the vicinity of the freezing point of the zinc samples were found to be absent. AS part of an over-all program of research on various phases of melting and casting nonferrous alloys, a systematic study of some physical properties of liquid metals and their alloys was undertaken in the laboratories of the Physical Metallurgy Division.1,2,3 The most recent phase of this work, on zinc and some zinc-base alloys, was carried out in cooperation with the Canadian Zinc and Lead Research Committee and the International Lead-Zinc Research Organization. One of the properties investigated was viscosity and the present paper gives results on pure zinc; the second part, on the viscosity of some zinc alloys, will be reported separately. Experimental interest in the viscosity of liquid metals has virtually been confined to the past 40 years. The capillary technique was already established as the primary method for the viscosity of fluids in the vicinity of room temperature; all relevant experimental corrections were known and an absolute accuracy of 1 to 2 pct was possible. Ap- plication of the capillary method to liquid metals creates a number of exacting requirements to manipulate a smooth flow of highly reactive liquid through a fine-bore tube. Consequently, the degree of precision usually achieved in the high-temperature field rarely compares with measurements on aqueous fluids near room temperature. However, the full potential of the capillary method has yet to be explored using modern experimental techniques. As an alternative, many investigators in this field have preferred to select the oscillational method. Unfortunately, the practical advantages are somewhat offset by the inability of the hydrodynamic theory to realize a rational working formula for the calculation of the viscosity. In attempting to overcome this restriction many investigators have employed calibrational procedures, even to the extent of selecting an arbitrary formula for use with a given shaped interface. However, where calibration cannot be founded on well-established techniques, the contribution of such experiments to the general field of viscometry is questionable. A critical appraisal of the viscosity data existing for pure liquid metals reveals a somewhat discordant situation where considerable effort is still required to establish reproducible and reliable values for the low-melting point metals. The means of rectifying this situation have gradually evolved in recent years. Here, the theory of the oscillational method has undergone major advances for both the spherical and cylindrical interfaces. The basic concepts of verschaffelt4 governing the oscillation of a solid sphere in an infinite liquid have been adequately expressed by Andrade and his coworkers.5,6 Employing a hollow spherical container and a formula, which had been extensively verified by experiments on water, absolute measurements on the liquid alkali metals were obtained. The extension of this approach to the more common liquid metals has been demonstrated by culpin7 and Rothwel18 where much ingenuity was used to surmount the problem of loading the sample into the delicate sphere. Because of the elegant technique required to construct a hollow sphere, the cylindrical interface holds recognition as virtually the ideal shape. On the other hand, loss of symmetry in one plane increases the complexity of deriving a calculation of the viscosity. The contributions of Hopkins and Toye9 and Roscoe10 have markedly improved the potential use of the cylindrical interface in liquid-metal viscometry. The relatively simple experi-

Jan 1, 1965

By A. R. T. Denues

LIQUID-OXYGEN explosives commonly consist of a carbonaceous absorbent enclosed in a canvas wrapper and soaked with a liquid containing more than 90 mol per cent of oxygen. Investigation of these explosives in this country was initiated in 1917 by George S. Rice, then Chief Mining Engineer of the Bureau of Mines. The early development is summarized in two papers.1,2 Their characteristics, advantages and disadvantages were considered in a recent bulletin of the Bureau of Mines.,3 Other publications of this Bureau4, 5 treat the technology of these explosives and contain adequate references to pertinent literature. These investigations defined the properties of liquid-oxygen explosives and improved them greatly; however, an outstanding disadvantage is their high inflammability, a property of critical practical importance. These explosives as hitherto prepared are easily inflamed; the combustion resulting from an accidental ignition is particularly dangerous because of the ease with which it passes into detonation. For this reason the Bureau of Mines undertook a cooperative investigation, which has resulted in the development of fire-retardant treatment for the minimization or elimination of this hazard without materially impairing the explosive properties, including the ease of detonation. This presentation will offer a general description of the investigation and the outstanding results. Further phases will appear in subsequent short papers, and the entire investigation including the results of detailed experiments will be available in a forthcoming bulletin of the Bureau of Mines (Bull. 429). The effects produced by fire-retardant treatments of the carbonaceous absorbent and of the canvas wrappers were investigated separately, and the efficacy of combinations of these treatments with particular reference to the possibility of inflammation and to the development of detonation from inflammation was studied. The experimental explosive was pre¬pared from a granular carbonaceous absorbent and. the results described maybe more or less unique for such a material. An extensive preliminary

Jan 1, 1940

THE Annual Fall Meeting held in Chicago in conjunction with the celebration of a Centennial of Engineering brought forth a round of field trips and symposiums which did much to add to the store of information of the 240 who registered for the gathering. Instead of a scattered program, technical papers were grouped together in organized symposiums, where the particular importance of each report was enhanced by presentation in context. Despite the heavy accent on technical papers and informative field trips, those attending the meeting had ample time to enjoy the benefits of a visit to Chicago. The AIME dinner dance was held at the Palmer House, in the Red Lacquer Room. The Chicago Section played host Friday evening at dinner. The MBD held four sessions at the meeting headquarters, the Palmer House, September 4 and 5. Featuring the meetings was a review of taconite concentration and new theories on comminution. The first session opened with a paper on the Structural Features Which Effect the Concentration of Iron Formations, presented by F. J. Tolonen. The paper was centered upon the various members of the low grade iron formations of the separate Michigan districts. The study correlated macrostructure, microstructure, and concentration tests. [ ] Beneficiation Characteristics of Michigan Low Grade Iron Ores, presented by F. X. Tartaron, cochairman of the session, reviewed the work of his laboratory on the beneficiation of low grade ore taken from various strata of a deep shaft on the Marquette Range. The paper included data on flotation, gravity separation, magnetic separation, and combinations of these processes. The economics of low grade ore treatment generated great interest. Ty. Maki offered a compilation and correlation of field results with magnetic separators in ferrosilicon and magnetite medium recovery circuits. Following the morning session, 130 persons attended a luncheon, followed by a brief business meeting. Later, a film illustrating the grinding, separation, and pelletizing steps investigated by the Mines Experiment Bureau, was presented by H. H. Wade. T. E. Ban, and L. J. Erck gave a report on pelletizing which evoked much discussion. R. A. Limons presented a paper on the Mineralogy of Blast Furnace Sinter, for its author, H. M. Kraner. Friday sessions featured a new hypothesis for high speed drill rod milling and a new technical approach to comminution. Jack Myers commented that Consolidated's large rod mill was a hammer mill turned inside out. Steve Erickson described the use of Cyclones for Heavy Media Concentration of Iron Ore Fines. Bob Meaders gave a Progress Report on the Aerofall Mill. Shiou-Chuan Sun described an improved high frequency analyzer for studying the conductivity of suspensions of various minerals. L. A. Roe discussed a magnetic reflux condensor which enabled him to determine the degree of liberation of magnetic iron ores. Roy A. Johnson described a function of the hydroscilator in which the fan rake was eliminated in favor of a conical bottom. The Industrial Minerals Division sessions held September 5 and 6 and were well attended. The Friday morning session was particularly concerned with developments and advances in industrial minerals with special emphasis on the Chicago area. The first two papers dealt with transportation on the Great Lakes and fuel movement into the Chicago area. The third paper proved to be of great interest, turning the spotlight on the fairly new hydraulic mining methods introduced by a silica company in the Ottawa, Ill. field.

Jan 1, 1952