Search Documents

By Fred D. Wright, Philip B. Bucky

FOREWORD By E. D. Gardner[$] THE present known petroleum reserves are limited, and unless important new fields are discovered the Nation will be dependent, in the not too distant future, upon imports or upon synthetic liquid fuels to supplement domestic petroleum supplies. As a national defense measure, it would appear desirable to develop a substitute source of liquid fuels within the borders of the country if new discoveries of petroleum should prove disappointing. Congress undoubtedly had this in mind when it passed the Synthetic Liquid Fuels Act (78th Congress, approved April 5, 1944). The act directed the Bureau of Mines to construct and operate demonstration plants for producing synthetic liquid fuels from coal and oil shale, and from forestry and agricultural products. As a part of this program, the Bureau of Mines has built a demonstration plant at Anvil Points, near Rifle, Colo., for retorting the oil shale, and has developed a mine to supply the plant with oil shale. At the beginning of mining operations, the physical qualities of the oil shale, which would have a bearing upon the selection of mining methods and practices for exploiting the deposits, were largely unknown. A comprehensive mining-research program has been set up to determine the best methods and practices to follow to obtain the lowest overall practicable mining cost for producing the oil shale on a large scale. Unusually low mining costs will be necessary for shale oil to be produced commercially. Consideration now is being given to exploiting a series of flat-lying beds 70 ft thick by a room-and-pillar method of three benches with the advance heading at the top. This report is one of a series giving the results obtained in research on mining problems. INTRODUCTION The structure and physical qualities of the oil shale indicate that the 70-ft interval of the oil-shale measure can be safely mined in open stopes; studies indicate that this method would be the most economical one to use.1 As labor will be a major item of expense, the largest equipment that could be operated efficiently in the workings would be required to obtain the lowest practicable mining cost. It was therefore desirable to know the maximum safe span of unsupported rooms and the size of pillars necessary to support the overburden. This paper describes the work done at the Columbia School of Mines Barodynamic Laboratory in determining the maximum safe unsupported roof spans and the minimum safe pillar dimensions for the oil-shale mine at Rifle, Colo.

Jan 1, 1947

By E. C. Barfield, D. G. McCarty

Two-dimensional analyses offer considerable promise in providing the basic information required to effect more precise control of petroleum reservoir performance. This paper describes a method for conducting some engineering analyses of this type using a high-qreed digital computer. The general approach is to (I) develop a representative numerical model of the reservoir and (2) employ a suitable numerical technique to solve the basic equation of flow and to develop the required engineering information for the particular case represented by the model. This technique has been used to calculate pattern performance in connection with several field projects involving water injection into oil reservoirs. This type of analysis involves sequentially (I) calculating the pres-' sure distribution in the reservoir and (2) tracking the progress of the interface between the displaced and displacing fluids in a step-wise manner to provide a depletion history of the operation. The particular analysis presented in this discussion is subject to the restriction that the mobility of the displaced and displacing fluids be equal and assumes that the fluids are incompressible and that gravity and capillary pressure do not affect the shape of the flood pattern. Complete two-dimensional .flexibility is maintained with regard to definition of reservoir rock and fluid characteristics, placement of physical restrains and boundary conditions, investigation of flow characteristics in the reservoir, and movement of the displaced and displacing fluid interface. The results of these studies indicate that the highspeed digital computer is well suited for conducting reservoir performance studies in two-space dimensions and that dependable numerical techniques are available for making such analyses. INTRODUCTION One of the problems facing petroleum engineers is that of providing more precise engineering control over reservoir operations at all stages during the depletion cycle. The most direct approach to this problem is to simulate the reservoir with some type of physical or mathematical model and use the information developed from the behavior of the prototype to predict the performance of the actual reservoir. This principle is, of course, not new, and a variety of simulation techniques have been developed to provide information on the behavior of oil and gas reservoirs. One straightforward refinement of present reservoir analysis techniques is the progress from one-dimensional reservoir models to those where the reservoir can be represented in two- and three-space dimensions. Multidimensional reservoir analyses are desired in order to show not only what is happening in the reservoir but in addition to show where in the reservoir the various phenomena of interest are occurring. Thus far, two-dimensional analyses have been confined predominantly to potentiometric and electrolytic model studies. However, when large numbers of wells are involved and where large-scale models are required, such problems become very tedious and instrumentation problems become acute." It is possible through use of numerical methods and general purpose digital computers to avoid many of the instrumentation difficulties and to relax some of the restrictions of previous techniques. The purpose of this paper is to discuss some recent experiences with the use of high-speed digital computers for predicting pattern performance in fluid injection operations and to describe the numerical procedures which have been used for making such analyses. THE NUMERICAL MODEL The problem of representing the reservoir with an appropriate numerical model is composed of at least two important considerations. The first requires that an adequate description of the reservoir mechanism be formulated in the form of the basic differential equation describing the process. The second consideration is definition of the physical characteristics of the reservoir. The latter requires that representative basic data be obtained, examined, and interpreted to provide sufficient detailed definition of the pertinent physical properties throughout the system. The Differential Equation One of the basic assumptions made for the purpose of performing the two-dimensional studies being dis-

By R. Greenwood

The advent of the space age and its promise of interplanetary flight has prompted new ideas for propulsion systems that will allow maximum energy with minimum fuel weight. The use of cesium as the source of energy for such rocket flights has been found desirable. Theoretical efficiency of a rocket fuel is measured in terms of specific impulse, defined as the number of pounds of thrust per pound of propellant consumed per second. Specific impulse is usually expressed in seconds (the number of seconds for which one pound of fuel would produce one pound of thrust) although it is really a measure of total energy, not of power. The most sophisticated chemical fuels have a specific impulse of 300 to 400 sec; liquid hydrogen heated by nuclear reactor has a specific impulse of 1000 to 1200 sec. Specific impulses as high as 20,000 sec, however, are theoretically attainable with the ion rocket, in which free cesium ions are accelerated across a voltage drop and ejected at high velocity.' Characteristics of the system have been sketched by Boden.2 The desirable properties of an ion propellant are: 1) low ionization potential, 2) low boiling point, and 3) high atomic weight. Alkali metals best fulfill these requirements, and Table I indicates the superiority of cesium. The use of heavy complex ions such as UCl3 is ruled out by their instability and other disadvantages.' Despite its enormous superiority in specific impulse, the ion rocket is inherently low-powered, capable of very small acceleration. Application of ion propulsion will be limited to large rockets and spaceships on missions requiring powered flight for weeks or months and employing a separate chemical propulsion system for escape from the earth's atmosphere where power requirements are large but of brief duration. For example, Kraemer and Larson3 considered the case of an unmanned 25,000-lb pay-load placed in a 300-mile orbit by chemical rockets, proceeding thence by ion propulsion to the vicinity of Mars, where it would go into orbit once again. Calculations provide for 8500 lb of cesium for such a voyage. The question of whether such quantities of cesium will be readily available to the space program does not appear to have been considered by geologists and mining engineers. Present Production and Uses Literature on industrial applications of cesium is scanty. The metal is used in scintillation counters, photocells, infra-red detection devices, and as a "getter" in low-voltage vacuum tubes. Production is sporadic and total figures are not published, but the annual consumption is measured in pounds rather than in tons. The few pollucite deposits known, small as they are, can easily supply the present limited demand for gram or pound lots of cesium. Until recently the price of cesium was $2 to $4 per gram, but according to Chemical Engineering, cesium salts are now available at $13 to $27.50 per lb. Geochemical Distribution As a large alkali ion, the cesium ion accompanies potassium in geological processes and tends to be concentrated in the latest crystallizing fractions of potassium minerals in much the same manner as rubidium. Most of the cesium in igneous rocks, therefore, is in the micas and potash feldspars of granites, and especially in granitic pegmatites. The cesium content rises markedly in the micas of the late by-drothermal replacement stage in complex pegmatite~.' Typically, cesium is only 0.5 to 0.01 times as abundant as rubidium in potassium minerals. Rb', with a radius of 1.47 A, is close enough in size to K' (1.33 A) so that rubidium forms no minerals of its own. Cs+ is so large (1.67 A) that only small concentrations can be taken up in potassium minerals; when cesium is present in solution in larger concentration it forms the mineral pollucite, Cs3-Na2A17Si17O48.3H2O, which is known only in pegmatites. In the weathering of igneous rocks, cesium is dissolved, carried to the ocean, and apparently in-

Jan 1, 1961

The Palabora ore consists of two types, a carbonatite containing a low titanium magnetite, and a foskorite containing high titanium magnetite. The latter type also contains substantial quantities of phosphate. These two ore types are separately crushed and are kept separate through copper flotation and magnetic separation, for recovery of magnetite, with the low Ti magnetite being shipped as iron ore. High phosphate tailings are pumped to Foskor, a government-owned phosphate plant nearby. The Palabora plant was originally designed in 1966 for 33, 000 tpd using two 54 in. by 74 in. Allis -Chalmers gyratories; two 7 ft (2. 13 m) standards; four 7 ft shortheads; and six grinding lines, each using one 1,200 hp rod mill and two 1,200 hp ball mills. A fifth short- head and one more grinding line were added later; and with flowsheet improvements, the capacity of the plant was increased to 59, 500 stpd. A further plant expansion involving a third 54 in. primary and two 32 ft by 15 ft (9.75 by 4.6 m) 9,000 hp autogenous mills and another flotation section will bring its capacity to 87,500 stpd in 1977. These two fully autogenous mills are constructed entirely out of doors near the primary crusher, and the ground ore will be pumped a mile to the concentrator by a five-stage pumping system. The Palabora ore is mined with 6, 10, and 12 7d (4.6, 7.6, and 9. 2 cu m) shovels and hauled to the crushers in 110 and 165 st trucks. Sixty-five ton trucks were originally used, but the crusher dump pockets were designed for larger units. Dump pockets, crushers, feeders, and take- away belts are offset in order to keep the two ore types separate. Centerlines of the crushers are only 43 ft (13. 1 m) apart; but, because of their being offset, maintenance room is ample. Initially, more carbonatite ore than foskorite was mined; but as the pit has deepened, this ratio has been reversed. The Palabora ore breaks in the pit with a large amount of oversize boulders; and, with the use of larger trucks, a splitter has been installed on one side of each dump pocket to protect the crusher spider. Smaller trucks dump on the opposite side. To accomodate the splitter, the pocket edge has been raised one meter and moved back one meter. Dust is collected through a special vent shaft between the crushers and the mantle relining area; but even so, two high-pressure water spray headers with nozzles are installed under the edge of the pocket at each dumping position. While only one truck dumps at a time, sprays from all four headers are used to suppress dust. Any leakage of water through the seal around the upper bowl of the crusher is caught by a circular trough under the seal and directed to a sump pump. At this point, there

Jan 1, 1978

By W. C. Weslow

AN extended program devoted to the development of a matrix for holding diamonds of a size and kind not heretofore generally used is being carried on by the Carboloy Company, and this paper describes the part of the development that affects mining and its allied industries. Laboratory and field work so far has indicated the following: 1. Tungsten carbide and cobalt form the most desirable known matrix material for the holding of diamonds for drilling work. 2. Industrial bort diamonds in sizes and of a class not generally heretofore acceptable and therefore less expensive can be successfully held in this cemented carbide matrix. 3. In exploratory drilling, the combination of bort diamonds, impregnated throughout a matrix of tungsten carbide and cobalt, when fabricated onto drilling crowns, is an indicated economic substitute for drilling crowns in which the diamonds are set by hand, mechanically or by casting. 4. This impregnated type of drilling crown or bit has definite possibilites of revolutionizing the drilling of blast holes, particularly in the harder formations. This will be brought about by the development of high-speed light-weight rotary equipment using an impregnated diamond bit to replace the percussion drill now in general use. (The development of this rotary equipment is well past the laboratory stage at this time.) 5. That the use of a rotary bit is a preventive measure in the fight against silicosis. The development of this product was started by G. F. Taylor at the Research Laboratories of the General Electric Co. It was early recognized that it had possibilities in the drilling field and the present product is the result of considerable experimental work with other powdered metals as well as with tungsten carbide and cobalt. In the study of the potential application to the mining field, it was learned that carbon diamonds originally were given a high rating of performance but that the trend had been toward borts in selected sizes

Jan 1, 1940

By J. W. Ristori, V. R. Garfias, R. V. Whetshel

During the past eight years, in trying to estimate world consumption of petroleum and related products, the authors have been unable to account for all the supplies available in any one year. There has remained at all times a balance, which at first was thought to represent almost entirely additions to stocks in foreign countries. But as this discrepancy continued year after year-over 148,000,000 bbl. in 1937—it became unreasonable to conclude that corresponding additional foreign storage capacity was continuously being made available. It became therefore clear that the balance in question was due to other causes than to additions to stocks. Last year Mr. A. G. White, Chief Economist of the Petroleum Economics Division of the United States Bureau of Mines, pointed out to one of the authors that an unknown and important factor in consumption of petroleum and related products is to be found in the requirements for military purposes in foreign countries. This paper is the result of Mr. White's timely suggestion. There are no reliable data available either on the storage capacity, and therefore oil stocks, or on the petroleum consumption for military purposes in foreign countries. This information is so closely related to national defense that its divulgation is forbidden. One can therefore but surmise as to these facilities and needs in line with the relative strength of the military land, air and sea forces of the various countries. The authors have assumed many of the component factors that go to make the tables herein presented, such as fuel consumption of fighting ships in relation to tonnage and horsepower, gasoline consumption of air fleets in relation to number of planes, and the consumption of petroleum products by mechanized armies; but in making these assumptions they have availed themselves of the advice and counsel of those whose wide experience in these questions make their views authoritative. The opportunities for error in an estimate of this nature are obvious and ever present; to illustrate: The air fleets in Spain no doubt consumed

Jan 1, 1938

By C. R. Clark, G. Swift, D. S. Roberts

The purpose of this investigation was to measure PVT behavior of various types and combinations of heavy hydrocarbon components from the paraffinic, naphthenic and aromatic classes where the relative proportions Of the various components were selected to approximate those of natural gas or gas condensate systems. Synthetic mixtures were used so that the compositions Of the various components could be measured accurately. n-Heptane, methylcyclohexane and methylbenzene were used to represent the paraffinic, naphthenic and aromatic components of the heavy fraction. In the mixtures studied, the heavy fraction composition was held constant at O. O5-mole lraction, the balance being methane except for one mixture where 0.10-mo1e fraction of an intermediate component, propane, was added. The PVT data for the mixtures were determined in a variable-volume, constant-mass apparatus at psuedo-reducedtemperatures from 1.84 to 2.00, over a pseudo-reduced pressure range from 2.3 to 12.0. The experimental results showed that, regardless of the type of heavy material (paraffinic, naphthenic, aromatic, or combinations thereof) mixed with methane or methane and propane, the compressibility factors at equal values of pseudo-reduced temperature and pressure varied by less than 2.2 percent. INTRODUCTION PVT data is used for natural gas and gas condensate fluids in determining reserves of reservoirs and performance of wells, in metering produced fluids, and in recombining samples for laboratory studies. While there are vast amounts of PVT data reported for natural gas and gas condensate systems from which useful correlations have been developed, ' the compositional analyses for these systems and the resultant correlations typically were made with components analyzed through some arbitrary carbon number, usually C6, with the residue reported as a lumped "heavy" fraction. The heavy fraction was stoichiometrically recombined on the basis of an apparent molecular weight to give the final compositional analysis. It is virtually impossible to make a systematic analysis of the effect that variation of the relative amounts of paraffinic, naphthenic and aromatic constituents of the heavy fraction of natural systems might have on PVT behavior. Because there is considerable latitude in the relative amounts of these constituents, one speaks of crudes or condensate liquids as being "paraffin base", etc. It is of interest to determine if changes in the relative amounts of these three types of hydrocarbons in the heavy fraction cause significant changes in PVT behavior. If so, steps should be taken to describe better the nature of the heavy fraction in PVT correlations. If not, more confidence can be placed in the correlations presently employed. DESIGN OF THE EXPERIMENTAL INVESTIGATION We attempted to determine if changes in the base of the heavy fraction would cause significant changes in the PVT behavior of gas or gas condensate fluids. Synthetic mixtures were used to enable us to systematically vary the base of the heavy fraction and to analyze accurately the fluids. We found that the heavy fraction of naturally occurring condensate systems seldom exceeds 0.05-mole fraction. Thus, the mole fraction of the heavy fraction in the synthetic systems studied was set arbitrarily at 0.05, to maximize whatever deviations in PVT behavior that might occur. Further, we judged that since the C7 hydrocarbons normally are present in greater quantities than higher carbon number hydrocarbons in naturally occurring systems, the use of n-heptane, methyl cyclohexane, and methylbenzene to represent the paraffinic, naphthenic, and aromatic species in the heavy fraction would be most appropriate. Finally, to enable us to compare our

Jan 1, 1970

By J. J. Arps

n approach to the study of the electrical properlies of drilling muds, their cakes and their filtrates was made by treating the drilling fluid as a porous medium. Lluring this study it was found that the weight pararneter was omitted from previous investigations on electrical properties. Patnode in 1949 made a similar approach to ,his investigation. His work showed that there was a variation of resistivity relationships with per cent Puid present in a given suspension. This present study ex-tends Patnode's investigation to one in terms of the solids fraction of the drilling fluids. Previous investigations were made on low weight muds where the effect of the rolids fraction was obscured. The following equationr were fitted to data taken from 94 field muds and 47 laboratory muds (see Tables I and 2). The parameter, C, is a complex function of the solidr content, or mud weight, of a drilling fluid. It was also found that for all drilling muds examined. A nomograph is presented combining Eqs. I and 2. INTRODUCTION It is generally recognized that the materials present in drilling muds affect the relationship between mud filtrate and mud resistivities. However, most electric log interpretations proceed with the assumption that the mud resistivity and temperature are the only important parameters needed to obtain a filtrate resistivity or a mud cake resistivity. Lamont1 suggests that only average relationships exist between mud cake, mud filtrate and mud resistivities. He indicates that there is limited accuracy when these intercorrelated factors are used since no other measure-able variable is apparent. A previous paper by Patnode indicates that drilling fluids may be considered to be a system of fluids in solid particles which may be correlated electrically in a manner similar to rock solids. 1 he equation for the resistivity factor. F = (per cent fluid) is satisfied for a given clay type in water, but the value of m varies as different materials are used in the water. The resistivity factor is not constant for a given amount of clay. As is suspected it varies as the solids fraction conducts electrical current. Since both weighting material and clay solids are present in commonly used drilling fluids, it is expected that both materials contribute to the variation of the m factor in Eq. 3. An extension of Patnode's work is presented in this paper to show some of the interrelations which exist between the resistivities of mud cake, mud filtrate and mud. Use of these data enable a more accurate calculation of mud filtrate and mud cake resistivities if only the mud resistivity and weight are measured. EXPERIMENTAL The measurements of mud weight, fluid and solids resistivity, alkalinity, and chloride content of mud samples were made in this research. Mud samples representing drilling fluids from 94 Louisiana and Texas wells (Table 1) and 47 laboratory-constructed systems (Table 2) were used in the experimentation. The measurements of the mud properties were made both in the field and in the laboratory. The tests on the properties of weight, alkalinity and chloride ion were standard tests as described by API specifications. The resistivity measuring devices were constructed in the laboratory for this study. For details on the resistivity equipment see Fig. 1. The fluid cell

A. R. Ledoux,New York City: The so-called combination method " is generally used in assaying bar copper for silver. It has been modified from time to time. Briefly outlined

Jan 1, 1901

YOU must know, my Messer Bernardino, that all things in this world made by art or produced by Nature are made only for their own specific purpose. If there should be any that perchance should fail therein, they would be useless and imperfect, and those are in a state of imperfection that should have it and have not yet arrived at it. Thus, in short, when you have dug out the ore with so much labor and extracted the metals, when you have made from copper (in addition to other works) guns that are ready for military service and have then put them on

Jan 1, 1942

By P. Barnes

The object of this paper is to make a brief comparison of the outlines of several forms of ports for steel-melting turnaces, in reference chiefly to the proper mixture; of the gas and air, and to the direction in which the flame is thrown down into the interior of the furnace. In the illustrations on the accompanying plate, Fig. 1 shows a form of port designed by M, Pernot, of St Chamond, France. This is used with the dome roof preferred by him fur the revolving bottom that bears his name. From No. 1 has been derived No. 2. This is shown on the plans of Mr. A. L. Holley, and from them three large furnaces have been built and put into operation by the Springfield Iron Company. Fig. 3 shows an outline proposed by Messrs. Richmond & Potts for the Pernot furnace. In this the ports are brought in under an arched roof of nearly the ordinary form, instead of over the top of the roof, as with the dome of M Pernot, Fig. 4 shows a furnace as built by Krupp of Essen, Prussia, for fluid refining, or " washing "-—to use the briefer French term. in this the gas and air come into contact in broad sheets one above the other, Fig. 5 shows the form used by Messrs. Richmond & Potts

Jan 1, 1881

By John Tyssowski

IN 1925, Harry Howard Stout, then metallurgist for Phelps Dodge Corporation, while investigating the cleaning of cathode copper by various gases at elevated temper-atures below the melting point of the metal, observed in the laboratory that particles of pure copper heated in a closed tube filled with hydrogen seemingly "stuck together." By further investigation he found that there was actual crystal growth across the boundaries of the particles of pure metal; in other words, there was a complete new crystal realignment and growth throughout the newly formed copper mass. It was coalescence, not adhesion; the several parti-cles had become one unit. From this dis-covery has been developed the coalescence process, whereby copper of cathode purity is squirted out in semifabricated form from an extrusion press, by the appli-cation of about 3000 tons pressure on a 10-in. piston. Stout decided that cathode copper pro-duced by electrolytic deposition was the logical source of the pure copper required for the coalescence process, but as there was no way of reducing the ordinary tough commercial cathodes to the small particles required he was confronted by a serious problem at the outset. Under his direction, this problem was solved by William H. Osborn and Harry Howard Stout, Jr. They developed the process and technique for producing cathode copper in brittle, friable

Jan 1, 1940

By E. H. Crabtree, T. C. King

The ferrosilicon grinding unit at the Central Mill of the Eagle-Picher Mining & Smelting Co. near Picher, Okla., was completed in March 1947. The object of the plant was to grind pigs of ferrosilicon, having a size of approximately 1½ by 4 by 12 in. and an analysis of 85. pct Fe and 15 pct Si, to approximately 100 mesh by crushing and wet grinding in a ball-mill classifier circuit. The minus-100 mesh ferrosilicon had formerly been purchased, and was used as medium in the heavy media process for treatment of lead-zinc ores. From the standpoint of dollars and cents, the cost of minus-100 mesh ferrosilicon was roughly $40.00 per ton more than pigs of the corresponding alloy delivered to the mill. Estimated wet grinding costs were considerably below this figure. The possible saving in cost of make-up medium for the cone plant was particularly attractive since, at that time, the plant losses averaged over four tons of minus-100 mesh ferrosilicon per day. Aside from the probable saving on the grinding charge, the need for such a unit was twofold. First, periodic fluctuations in the differential between the top and bottom densities of the cone were thought to be detrimental to metallurgy. There was little doubt that an intermediate differential existed at which the heavy media separa- tion was most efficient, representing a compromise between concentrate grade and tailing loss. Furthermore, if a finer, but considerably cleaner, medium could be obtained, there was the possibility that the differential could be decreased without increasing the viscosity, or conversely, the viscosity of the medium decreased without increasing the differential. Preliminary to experimental work aimed at pegging the cone differential and circulating medium viscosity at whatever values were found to be most efficient, it was essential to have control over both the nonmagnetic content of the medium and the particle size of the contained ferrosilicon. The latter was possible by means of a grinding unit at the mill. Second, whereas the ferrosilicon alloys are made by a number of manufacturers, only two, to our knowledge, grind it in any quantity for use in heavy media plants. For all practical purposes, the Central Mill was limited to one source of supply, a particularly vulnerable position. In case the supply was cut off, it was thought that pigs of the 85 pct Fe, 15 pct Si alloy could be obtained elsewhere, providing means of grinding them was available. There was no published information available covering wet grinding of ferrosilicon. Dry grinding in batch mills and in continuous mills with air classification was being practiced, but the cost of grinding was excessive and the dust condition objectionable. It appeared that primary and secondary crushing was no particular problem, providing heavy duty equipment was used;

Jan 1, 1949

By W. D. Faulkner, J. E. Urbanic, R. J. Jula

The process of treating granular activated carbon for return to service in the recovery of gold in carbon-in-pulp and carbon-in-leach circuits has been investigated. Carbons from two US mines, one Canadian mine, and a South African pilot plant operation were characterized before and after regeneration. Thermal regeneration of the carbon was investigated using factorial analysis to determine the effect of interaction of furnace temperature, retention time, and use of supplemental steam. The operation of acid washing the service carbon was investigated, including a comparison of the use of nitric and hydrochloric acids. The effect of quenching regenerated carbon was also briefly studied. Prom the data obtained, guidelines are given for effective regeneration operation.

Jan 1, 1986

By Axel Sahlin

Since the days of the infancy of metallurgical industries, slags of various kinds have been accumulating. Until a comparatively recent date hardly any employment had been found for these waste products, which have had, consequently, little or no value. An exception to this rule is the basic Bessemer slag, the value of which has become universally recognized. It is to-day one of the standard fertilizers of the world, and a price of from $15 to $20 a ton is considered reasoiable for the ground slag, which, especially in Germany, finds a ready market as fast as it is prepared. The slags from puddling and re-heating furnaces have only found vol. xx.—25

Jan 1, 1892

By T. Reed Woodbridge

The object of this paper is to bring to notice a method in use at the Cedar Point laboratory of Witherbees, Sherman & Co., for determining the phosphorus in the ore mined at Mineville, N. Y. This ore is magnetite, with a gangue containing crystals of apatite. In 1886, Mr. H. F. Dawes, then head chemist at the works, suggested that as all the phosphorus seemed to be in the apatite, it could be obtained in solution by dilute nitric acid. After some experimenting the following method was adopted, and has proved invaluable for rapidity and ease; half a dozen determinations requiring very little more time or trouble than one. From + to 10 grammes of ore are weighed into a 150 c.c. beaker; 50 C.C. hot water and 10 c.c. strong nitric acid are added; the beaker is covered and the contents are boiled for 1/2 hour (10 minutes sometimes proves sufficient; but 4 hour is safer). The bumping which ensues if more than & gramme is used need cause no trouble. The hot solution is filtered into a 250 C.C. beaker. The filtration and washing (with hot water) proceed rapidly, as the magnetite itself is but slightly acted upon. After the addition of 15 C.C. ammonia and 15 c.c. nitric acid, the solution is cooled to 45' C., and from 15 to 40 C.C. of molybdic acid solution is added and stirred vigorously. In 5 minutes the precipitate will be down, and the determination can be finished by any good method. At Cedar Point the method more commonly used is weighing as yellow salt. Good washed filter-paper is used, No. 0 Swedish being preferred; and dozen 3 1/2-inch filters are numbered and dried and weighed at 110°C. These are always kept in stock. The yellow salt is filtered on one of these, washed with dilute nitric acid (2 per cent. by volume); dried for 1 hour at 110' C., and then weighed, 1.63 per cent. of weight being calculated as phosphorus. The filters vary in the two weighings from

Jan 1, 1889

By L. J. West, R. M. Perrry

This chapter describes the rock mechanics studies performed for a high cut at a nuclear power station in Pennsylvania. Two units presently are being constructed on the Susquehanna River. When these units are completed, they will generate approximately 2100 MW of electricity. It was necessary to excavate about 1 million cu yd of rock to prepare the site. This excavation resulted in a high cut on the west and north sides of the station area with a maximum height of about 200 ft. The location of the high cut with respect to the plant facilities is shown on Fig. 1. The recommended slope angles ranged from 1 ½ (horizontal) to 1 (vertical) for the upper residual soil to ½ to 1 for the deeper competent rock. Because of the significant height of this cut and the fact that the slope is immediately adjacent to the proposed nuclear facilities, extensive stability analyses were performed prior to, during, and after excavation to evaluate the steepest angle at which the slopes could be safely cut. The studies consisted of evaluating both qualitatively and quantitatively all apparent factors which could affect the stability of the slopes. These factors include the strength of the material, the zones of weak material which are present along the planes of schistosity, the prominent joint systems, the ground water, and postulated seismic effects. FIELD AND LABORATORY STUDIES A comprehensive program of field explorations was performed to evaluate the geologic characteristics of this site. This program consisted

Jan 1, 1970

By D. J. Wynnemer, G. W. Preckshot

Precise electromotive force measurements have been made on the zinc-cadmium system over the temperature range 700° to 900°C. Activity coefficients, partial free energies, enthalpies, and entropies have been determined .for the entire composition range. The integral heat of mixing is positive and compares favorably with calorimetrically determined values. Vapor-liquid equilibrium compositions were determined .for a total pressure of 1 atm and these agree well with previous values determined in other ways. The use of electromotive force measurements to obtain thermodynamic data for liquid metal systems is a simple and well-known method. Several reviews of the various experimental methods and results have been published.2,3,11 However, most of the past work using this technique was carried out at temperatures slightly above the melting point of the alloy system where alloy composition changes due to vapor transport and increased metal solubility in the electrolyte are not important factors. One advantage of extending the electromotive force measurements up to and including the normal boiling point of the alloy is that it is then possible to evaluate the vapor-liquid equilibrium of the alloy at various pressure levels up to 1 atm. A detailed discussion of the thermodynamics of reversible electromotive force cells can be found in most advanced physical chemistry or chemical thermodynamic textbooks. The expression stating the inter-relation of the electromotive force and the thermodynamic functions is the Gibbs-Helmholtz equation.

Jan 1, 1962

By L. B. Underwood, C. J. Distefano

NORAD, when completed, will be housed in large chambers excavated out of the granite beneath the Cheyenne Mountain near Colorado Springs. A room and pillar layout for the chamber excavation was selected and executed. Many complex problems arose in designing a rock bolt system; this paper includes discussions on: rock strengthening following excavation, excavation and ground support problems, orienting rock bolts with respect to jointing systems, conducting pull tests, four-way chamber intersection problems, the need for grouting rock bolts, and loss of tension and permanency of anchorage in a rock bolt system. In the event of a sudden nuclear attack upon the United States, it is imperative that vital command and control centers have a high probability of survival. One such vital facility is the North American Air Defense Command Combat Operations Center at Colorado Springs, Colo. Known briefly as NORAD, this installation when completed will be housed in large chambers excavated out of granite beneath the eastern slope of Cheyenne Mountain (Fig. 1). The NORAD COC, a U.S. Air Force sponsored project, will serve as the primary collection and evaluation center for data concerning unknown aircraft, missiles, or space vehicles, which might bring destruction to North America. The data will be fed into high-speed computers and electronic equipment from outpost sources: radar, ballistic missile early warning stations and picket ships throughout the world. Electronically controlled display boards will make it possible to evaluate the tracking data instantaneously and to take appropriate defensive action.'

Jan 1, 1968

By John R. Spencer

A capillary tube variable volume cell is described, which has operated satisfactorily over a range of 100°F and 3,500 psi to 550°F and 1,500 psi. The cell contents are entirely visible over the length of the capillary with the exception of a space at the top amounting to three per cent of the total volume. Observations on the critical behavior of simple systems have been greatly facilitated by the apparatus, it being possible to establish the critical conditions for a particular mixture in the course of a day's run. INTRODUCTION Many types of apparatus have been designed for obtaining data on the phase relationships of hydrocarbon systems. Such apparatus can in general be subdivided into two classifications; (l), indirect measurement of phase volume, and (2), direct visual observation of phase volume, each of which has outstanding advantages and disadvantages. Indirect measurement of phase volume requires the use of rather elaborate apparatus including internal probes in which are located the device for determining the locus of the interface between phases. Such equipment is by its very nature costly, and is complex from the standpoint of operating technique. Probing techniques can be used, however, over wide ranges of temperature and pressure with a high degree of reproducibility. Apparatus for visual observation of phase behavior obviously has the advantage of enabling the experimenter to see exactly what takes place, but because the material to be tested is contained in a cell constructed of both metal and glass, is limited severely as to the temperature range of operation. Furthermore. the maximum pressure usually is limited by the choice of material used for sealing the glass to the metal, and by the strength of the glass itself. In the interest of increased efficiency of observation, as much of the cell as possible should be visible to the eye. Glass capillary tubes have been used successfully but have always given difficulty at the metal-to-glass seal. An apparatus has been devised to overcome the problems of sealing and resistance to temperature effects that have heretofore been the limiting factor with glass apparatus in the observation of phase volumes at elevated temperature and pressure. APPARATUS The objective which dictated the general arrangement of the apparatus (Figs. 1 and 2) was simplicity of operation. The air bath, A, was constructed of an iron framework to which was attached approximately one inch of glass wool bats which were covered on the outside with "Masonite." A roughly octagonal center piece was installed to provide forced circulation of the air by the fan, B, past the heaters, D, cell, F, and thermoregulator, C, respectively. The entire top of the box is removable to facilitate charging of the cell and to permit easy maintenance. Two windows are provided before and behind the cell to allow the operator to observe the contents against the background fluorescent light, E. The heaters,

Jan 1, 1951