Search Documents

By O. B. Buchlen, J. W. Smith

The Coal Research Bureau of the School of Mines at West Virginia University, using an experimental flotation cell designated an airlift-cyclone was able to obtain a clean coal product containing 7.64% ash with 94% yield and 97% coal recovery. This favorable performance was obtained with the experimental flotation cell operating as a simulated three-stage unit on slurry taken from the fine coal circuit of a coal preparation plant. This experimental device, consisting of a sheet metal cyclone-like unit mounted on a U-shaped uplift pipe, uses a combined flotation and cyclone action to beneficiate the minus 14 mesh partially cleaned feed product. In addition to providing comparable analytical results, the airlift-cyclone possesses other attractive features among them being a low capital expenditure, utilization of moderate plant floor space, efficient operation on high density feed slurry, and absence of moving parts. The primary shortcoming of the experimental cell is its limited capacity. The Coal Research Bureau presently has under construction a larger unit which, it is hoped, will provide the capacity and quality to establish the airlift-cyclone as a commercially feasible unit. Froth flotation of fine coal is a practice which has only recently gained wide acceptance in this country. Various explanations can be put forth for this delayed acceptance of a very selective and efficient system of coal preparation. Among these reasons would be the advent of continuous mining machines resulting in the increased production of coal fines, the change in market patterns from domestic and rail consumers who did not want fines to a predominantly utility market which normally consumes fines, and also the imposition of legal restrictions in regard to stream pollution. However, the major detriment is probably the high cost involved both in installation and operation of the flo- tation unit and auxiliary systems. These facts assume greater emphasis when considering that froth flotation installations normally process a low quality feed product. A recent estimate' of installation costs including dryers, filters, and other auxiliary equipment for a flotation system was $5000 to $7000 per ton of capacity while the operating costs, exclusive of auxiliary equipment, were estimated at 10 to 306 per ton of feed. The Coal Research Bureau of the School of Mines at West Virginia University is currently developing a simplified froth flotation cell, designated an airlift-cyclone, which may provide considerable savings in capital and operating costs without sacrificing product quality or recovery. This experimental cell consists of three primary components: 1) a vertically mounted U-shaped pipe; 2) an air injector device; and 3) an integrally mounted cyclone-like unit (Fig. 1). A feed slurry is introduced at the top of one leg of the U-pipe while compressed air is injected near the base of the other leg. The air serves both to aerate the pulp and to cause it to flow upward into the base of the cyclone unit where the floated clean coal is separated from the reject material and unfloated coal which remains in slurry. The Coal Research Bureau's experimental airlift-cyclone is somewhat similar in principle to a flotation device developed by Russian engineers in the late 1950's. In tests upon a two-stage pilot-size device, the Russians obtained very favorable cleaning efficiencies.' However, later experience with production models demonstrated that rated capacities and acceptable product quality could not always be maintained.3 Because of these limitations, Russian engineers subsequently recommended that conventional, mechanical cells be used when cleaning difficult to float slurries. Engineers at the Coal Research Bureau felt that such a device utilizing the combined actions of a cyclone and a froth flotation machine offered numerous attractive features and merited investigation. Accordingly, a small capacity experimental airlift-cyclone was designed and, with the permission of the Christopher Coal Company Div. of Consolidation Coal Co., installed in Christopher's Humphrey preparation plant near Morgantown, West Virginia.

Jan 1, 1964

By Abner Dixon

INTRODUCTION. IN India the production of mica, which in other countries is of very minor importance, is one of the staple, long established industries, and ranks high in the statistics of mineral products. Nearly two-thirds of the mica of commerce comes from India. The Indians have used mica for glazing and decorative purposes through many centuries. About 14,000 men are employed in and about the mines, and the indigenous and primitive mode of mining is still followed; but, by reason of the exhaustion of the surface supply hitherto won without intelligence or capital, it will not be many years before the present interesting and casual methods will be replaced by a less archaic and more profitable system. India on the whole has little mineral wealth, but the unique resources of its mica fields, cheap labor, and favorable natural conditions render it unlikely that any other country can ever more than temporarily contest her leadership in the production of this one minor but essential mineral. Mica plays a small but indispensable role in a variety of fields of dissimilar application. Its use and value depend upon characteristics which different kinds of mica have in varying degrees, each kind being adapted to 'its own special purpose. Its well-known characteristics of transparency, flexibility, elasticity, toughness, high dialectric, strength, perfect flatness; ease of splitting into thin films, ability to stand high heat and sudden changes in temperature, give it value in many industries. No other substance, natural or artificial, has this combination of qualities. The oldest use of mica is in glazing. By reason of the improvements in annealing glass, this is not now of great importance, but mica is still employed for the covers of ikon images in Russian churches, the windows of anthracite stoves, compass

Jan 5, 1913

By Leon Y. Sadler, E. K. Landis

Froth flotation has been described by several authors" as being analogous to a first-order rate process. Although a few investigators"," have found orders other than one fit their data best, the rate is described most often by the first-order equation, [ ] where r is rate of disappearance of floatable mineral by flotation, C(t) is concentration of floatable mineral in the cell, t is time, and k is first-order flotation rate constant. One of the difficulties in using this rate equation to develop a mathematical description of an actual flotation process is the determination of a suitable value of the constant k. The value of k, which reflects the floatability of the floatable mineral, is dependent on the hydrodynamic conditions in the cell, type and concentration of flotation reagents used, pulp density, and pH, method of froth removal, aeration rate, particle characteristics, and many other factors. Therefore, it is reasonable to expect that each particle of floatable material has a distinct value of k and that a unique distribution of k values exists for given feed and cell conditions. This has been observed and discussed by several investigators, and mathematical descriptions of the batch cell and steady-state continuous cell with distributed flotation rate constant have been developed." The mathematical description in the form of a transfer function of the continuous or flow cell under unsteady-state conditions with a distributed flotation rate constant has not been presented in the literature. The purpose of this note is to make such a presentation. The basic features of the perfectly mixed continuous

Jan 1, 1974

By J. R. Dawson, J. A. Glunt

VESTA No. 4 and 5 mines supply most of the high volatile coal required for Jones & Laughlin's byproduct coke plants. Until 1944 all coal produced in these mines was loaded by hand. Pressure to mechanize at Vesta was brought on by the manpower shortage in World War 11, and in 1943 a decision was made to change to mechanical loading. It was the opinion of those concerned that by use of selective mining the coal would be clean enough to be processed by the existing preparation plants. At that time coal cleaning at Jones & Laughlin consisted of hand picking the larger sizes at the mine tipples and wet washing at plants located at the Pittsburgh and Aliquippa Works. A typical section of the Pittsburgh seam as it occurs at Vesta is shown in Fig. 1. The 14 to 16 in. of drawslate immediately over the coal is too soft to be used for roof and must be taken down, leaving the rooster coal just above for roof. In selective mining an attempt is made to mine the coal under the drawslate first and then load out the drawslate separately as refuse. In full seam mining slate and coal are shot down at the same time and loaded out. Mechanical loading at Vesta created new problems. It was found that selective mining, even when carefully applied, increased the refuse in the raw coal to such an extent that the washers at the mills were unable to handle it. Large tonnages of refuse were being transported, a reject disposal problem was created, and good metallurgical coal was being loaded out and lost. In addition, the selective method handicapped operation of the loading machines. Fig. 2 shows how the ash content of the raw coal increased as mechanization proceeded at No. 5 mine. New Preparation Plant: After an exhaustive study of this situation by J & L management, is was decided that a preparation plant should be constructed at the mines, capable of handling full seam mined coal and large enough to process full production of both No. 4 and No. 5 mines. It was decided that from the standpoint of inside operation and haulage the new plant should be located as near as possible to the old No. 5 tipple on the Monongahela River near Vestaburg. Full seam mining at Vesta could be expected to produce a tremendous volume of refuse along with the coal, since 14 to 16 in. of slate would be mined with an average 78 in. of coal. Disposal of this refuse required serious consideration in selecting a plant site. The only area near Vestaburg large enough for disposal of the plant refuse was across the Monongahela River at LaBelle. Ample space was available here, and construction at this location would not interfere with operation at the No. 5 tipple. It had been noted over the years that the sulfur content of the coal produced at Vesta was gradually increasing, and there was every indication that this increase could be expected to continue as the mines developed further from the river. It was decided to construct a three-part separation plant with complete blending facilities to produce both metallurgical and steam coal. In this system an attempt is made to reduce the sulfur in the metallurgical coal in a secondary cleaning process. Construction of the new preparation plant got under way early in 1947 and continued until the spring of 1950. The plant was designed to handle 2400 tph of raw coal containing 30 to 35 pct refuse. Cost of outside buildings and equipment was about $14 million. Total cost of the plant, together with improvements and changes made at this time, was approximately $21 million.

Jan 1, 1957

By K. D. Jacob, W. L. Hill

Fluorine recovery in the United States has been restricted chiefly to manufacture of ordinary superphosphate and wet-process phosphoric acid. However, there is an expanding use of fluorine by industry in the form of hydrofluoric acid. Improved methods for recovering fluorine from phosphate rock would yield an adequate supply of fluosilicates and a substantial contribution to the hydrofluoric acid requirement. THE bulk of natural phosphates is comprised of calcium phosphates, which are usually apatites;' calcium aluminum phosphates such as pseudowavel-1ite; and aluminum phosphates, which occur in extensive deposits, notably on Grand Connetable Island." Nearly all deposits of current commercial value are apatite, often with admixed material of other classes. In the trade coarsely crystalline material, mainly fluorapatite of igneous origin, moves as apatite, whereas the fine-grained material of sedimentary origin is marketed as phosphate rock. The latter classification includes the phosphate shales in western North America. Although several genetic varieties of phosphate rock are recognized, most known reserves are of marine origin. Calcium phosphate is concentrated from Florida land pebble and Florida hard rock deposits and from Tennessee brown rock deposits. Phosphate Rock as a Fluorine Carrier: More than two decades ago Reynolds and Jacob surveyed the fluorine content of commercial phosphate rock from various parts of the world. Later these samples were re-analyzed by a new and more reliable method of determining flourine. The revised results with interim additions of new samples, published a few years ago in a brief summary," are shown in Figs. 1-3. Through the points representing the respective varieties of rock medial straight lines are drawn. In some instances the lines are well defined by the points; in others, where scattering renders the position of the best line uncertain, the greater weight is given points near the end of the covered range. Wherever distinct varieties are not recognized among regional deposits the custom is to identify the sample with the geographical location of the deposit. Although all rock varieties cannot be classified with certainty, the plotted results exhibit three distinct types of rock in which the F to P2O5 ratio diminishes, remains sensibly constant, and increases, respectively, as the grade of rock increases. Existence of two types of Florida land pebble, Fig. 1, is supported by additional results recently supplied by a producer." Generally speaking, phosphate rock from continental deposits carries considerably more fluorine, and apatite and insular phosphates less, in proportion to the phosphorus content than is required by the formula for fluorapatite. Exceptions to this are apatite from Canada and certain samples of Florida waste-pond phosphate. The manner in which excess fluorine is held and the nature of the carbonate in carbonate apatite are discussed in recent articles. High-grade calcium phosphates with F to P2O5 ratios less than 0.05 have been found in Curacao, Christmas Island," Mexic,13 and elsewhere. The calcium aluminum phosphates and aluminum phosphates aften carry notable amounts of fluorine. The F to P2O, ratio for one sample of pseudowavel-lite concentrate was 0.05." Aluminum phosphate from Grand Connetable Island is very low in fluorine, whereas some aluminum phosphate minerals" carry as much fluorine as highly fluorinated phosphate rock. Fluorine in Domestic Phosphate: The curves shown in the figures permit interpolation of the F to P2O5 ratio corresponding to the midpoint of selected ranges in grade of any one of the several varieties of phosphate. Multiplication of the interpolated ratio by the mid-range grade (P2O5) yields a figure for the percentage of fluorine in this grade. Then, with the use of the mid-range grade, the amount of fluorine held in phosphate reserves can be estimated, see Table I. Accordingly, on Jan. 1, 1950, the fluorine complement of known domestic reserves exceeded 420,000,000 long tons of the element. A previous figure," deduced in 1940 by a simpler procedure

Jan 1, 1955

By Albert L. Toenges

Alaska requires an adequate fuel supply for its development, and has large potential coal reserves ranging from lignite to subbituminous and anthracite. Coal production in the Territory now is less than the requirements. In 1947, production was 361,000 tons, divided about equally between bituminous coal from the Matanuska field and subbituminous coal from the Nenana field. There is need for development of modern mechanized mines, which should produce the required output with a minimum of workers. These mines should not be thought of in the light of large potential capacity, as in the States. However, these new mines should be developed by modern methods, which should result in lower costs than at present. Because of the diverse physical conditions in the coal fields, intensive investigation by diamond drilling is necessary to properly plan the development and equipment of mine sites at minimum cost. The Bureau of Mines is doing this now in the Wishbone Hill area of the Matanuska field. All coal land in Alaska is government-owned and subject to the Coal Leasing Act.

Jan 1, 1949

The Subcommittee on Manganese, of the A.I.M.E. Committee on Industrial Preparedness, prepared under date of Jan. 24, 1924, for and at the request of the War Department, a confidential report on manganese as an element in the problem of national defense. This report was later released and published, in slightly modified form, as a separate pamphlet. After the lapse of eight years, in view of the vital position of manganese in the problem of industrial preparedness agenist a war emergency, the War Department made a request to have the onclusions of 1924 reviewed and brought up to date. To comply wi' this request the manganese subcommittee was reconvened and ex' tive studies were once more made of the entire subject of mang? . A new report, with specific recommendations, was submitted + War Department in February, 1932. This second report, with 4. L specific conclusions and recomrnendations expressed to the War Department omitted, has now been released and is hereby published. Following a rather brief discussion of uses of manganese and classification of manganese ores, requirements and sources are dealt with at some length. Domestic ferro-grade reserves are estimated on the basis of price and are shown by means of a curve where tons of metallic manganese are plotted cumulatively against prices ranging from 50¢ to $1.00 per unit; thereby indicating at a glance the tonnage which the Committee believes would become commercially available at any particular price per unit. Foreign sources of ore are described and foreign prices which the domestic producer must meet are considered. The question of a war-emergency reserve is then analyzed, requirements are balanced against apparent resources, and the principal conclusion that emerges is that a war reserve or stockpile is still vital to national defense.

Jan 1, 1934

ROBERT M. KEENEY,* Portsmouth, Ohio (written discussion?).- Mr. Coffin has written a most interesting paper that covers most of the uses to which water-cooled devices are subjected; but to meet with the operating department's approval, these devices must effect a saving in cost per ton of ingots produced in the furnace. The making of steel in the open-hearth furnace is dependent entirely on the personal element. It is not possible to charge the furnace with so much raw material, turn on a valve for heat, and by use of recording thermometers, clocks, etc. empty the furnace when a steel is made. Competent men trained to the work must be in charge all the time, and the quality and quantity of steel produced is quite as dependent on the care and working qualities of the furnaces as on the raw material and working of the charge itself. Steel making is hot, hard work and the inducement offered to technical men to take up this work is not sufficient to induce many to enter the field. The result is that most of the workmen in an open-hearth plant, the men who actually operate the furnace and make the steel, are not technical men and do not understand the "whys" and "wherefores " and care less. All this means that a furnace must be built as nearly fool-proof as possible. By this I mean that it is necessary to protect those parts of a furnace most subject to abuse by water-cooled devices whenever possible, and these water-cooled appliances must he as nearly fool-proof as they can be made. The control of the gas entering a furnace is of the utmost importance. This means a properly designed port must have the same design throughout the whole run of the furnace. This is not possible with the ordinary

Jan 6, 1919

By E. P: Mathewson

Discussion of the paper of E. P: Mathewson, presented at the Butte Meeting, August, 1913, and printed in Bulletin No. 78, June, 1913, pp. 1033 to 1037. PROF. JOSEPH W. RICHARDS, South Bethlehem, Pa. :-Speaking to the question of the development of the basic lining, and speaking from a somewhat considerable study of the history of the process, ,I think Mr. Mathewson's conclusion (in the last paragraph. of his paper) is perfectly justified and is very fairly stated. Messrs. Smith and Pierce worked at developing their process for many years ; copper men had been trying their level best to get away from the silica lining of the converters and had uniformly failed. On one page of Mr. Mathewson's paper we read that at the old works of the Anaconda Company, at Anaconda, the experiments " were abandoned on the score of cost and lack of advantages." On the next page, after describing the work of Messrs. Smith and Pierce, we have the statement that the Anaconda Company lined a shell with mangnesite brick and the ?results were excellent." I think Mr. Mathewson's statement that to Smith and Pierce belongs the credit of developing a long-discredited idea, is correct. C. D,. DEMOND, Anaconda, Mont. :-It seems to me that the matter of the lining is important; my impression is that they used tar in their basic lining and that did not seem to be at all successful at Anaconda, but silicate of soda was very successful. MR. RICHARDS :-I did not know that they- had abandoned the use of tar. MR. DEMOND :-I said I thought that was the practice. At Anaconda that was not at all satisfactory in the basic linings. Silicate of soda was very satisfactory and is so.

Jan 11, 1913

By Sir Robert A. Hadfield

The Hadfield method of producing sound steel ingots has been the subject of a paper read before the Iron and Steel Institute, so that it will be unnecessary to describe it fully here. The object of the method is to make poseible the production of steel ingots in which the pipe is almost entirely obliterated, and it is applicable particularly to the production of sound ingots, from which good rails could be rolled. The method in brief consists in casting the ingots on cars, usually with the small end down. Each ingot mold is provided with a sand top, rammed up in the well-known manner. After the mold is filled to the desired height with steel, a layer of slag about 0.5 in. thick is placed upon it and the balance of the mold is then filled with charcoal. Then, through suitable piping, an air blast is directed in numerous jets upon the charcoal, which is burned thereby, the combustion supplying addi, tional heat to the top of the ingot, which helps to keep the top fluid and to retard its solidification, while the lower parts are rapidly losing heat by its transfer to the mold. By one plan the ingots are cast in molds placed upon bogies, movable trucks, or platforms, in the position A, Fig. 1. The ingots are cast vertically on bogies, say four or more ingots on each bogie, as may be found most convenient, and the upper surface of the steel is maintained in a molten condition during the transit of the ingots from the casting pit to the stripper. This is effected by a series of air pipes, for example, three in number, with jets or holes on the under surface of such pipes, placed preferably horizontally, arranged in such a manner as to cause jets of air to impinge on the upper surface of the ingots. These holes or jets are made throughout the entire length of the overhead pipes, the length of such pipes being

Jan 1, 1914

By FRANK RIEBERS

IN DISCUSSING the selection of a geophysical method, much of what the writer will say is applicable to any of the various methods and to their use in prospecting, whether for oil or for other minerals. Specifically, the writer's subject is the problem, particularly pressing on the Pacific Coast, of checking the rising cost of the discovery of new fields by the proper employment of geophysical methods. Table I was prepared from statistics published by the California State Milling Bureau. The writer selected five of the largest a:ld most active companies operating in California, segregated the number of wild-

Jan 1, 1930

By E. V. Daveler, Frank L. Antisell

CERTAIN physical and chemical properties of copper are so intimately related that a change in variation of the physical properties indicates a certain chemical change. The standard specifications of copper of the American Society for Testing Materials are based upon physical characteristics with one exception, namely, the copper contents. Certain phenomena of the surface indicate the adaptability of the metal for forging or rolling. The writer believes that it is much simpler to produce shapes that are metallurgically correct than those that are mechanically satisfactory. The appearance of the surface of the copper when cooled is considered as to its "pitch," or the general contour of the surface, and the "set," or the decail appearance of the surface of the shape. The set of the copper is, in a very large measure, directly related to the pitch; and so intimately are these characteristics connected that they are often used as synonymous terms by the refiner when he is speaking of well-refined copper. Oxygen is often spoken of as a medicine for copper, it being used to regulate the pitch.

Jan 1, 1920

By S. D. Thompson

An AIME transaction by P.L. Allsman (1960), "Analysis of Explosive Action in Breaking Rock," contains many useful concepts applicable to blast design. Of special interest was the derivation of a heave blasting burden formula, which is important in establishing the maximum burden. Unfortunately, its derivation contains a fundamental error and then a compensating one. This formula was: [bImpulse _P d At max =nwuwu where: bmax = maximum burden in m (ft). P= average detonation pressure in N/m2 (lb per ft2). A= duration of the average detonation pressure in sec. n= 3.1416. w= specific weight of rock in N/m3 (lb per ft3). u= minimum velocity that must be imparted to the rock in m/sec (ft per sec). d= borehole diameter in m (ft).] The derivation used the impulse-momentum principle, with a 0.3 m thick (1 ft thick) radius of rock mass being acted on by an explosive impulse. However, the rock weight was not converted to mass by dividing by the gravitational constant. This mistake can be verified by checking the units in the formula, which resolve into m1/2-sec instead of meters. Adding the gravitational constant corrects this: [P d Atbmax =gu g = gravitational constant equal to 9.81 m/sect (32.2 ft per sec2).] If the minimum velocity is now taken as 0.3 m/sec (1 ft per sec), as was recommended, excessively large burdens result. Any appropriate rock velocity should be capable of throwing the rock mass a minimum distance so that the swell needed for breakage can occur. Unless the burden is extremely small and the bench height is very high, it is unlikely that a velocity of only 0.3 m/sec (1 ft per sec) will be sufficient. A review of the literature indicates that average rock velocities observed by camera studies typically range from 15 to 30 m/sec (50 to 100 ft per sec) (duPont deNemours and Co., 1977; Tansey, 1979). On this basis, a minimum rock velocity of about 15 m/sec (49 ft per sec) would be expected and not 0.3 m/sec (1 ft per see). When a velocity of 15 m/sec (49 ft per sec) is inserted into the corrected formula, the results approximate those of the original formula with a velocity of 0.3 m/sec (1 ft per sec). The errors were approximately self-compensating [(9 = 1.24)]. ? References Allsman, P.L., 1960, "Analysis of Explosive Action in Breaking Rock," Transactions, AIME, Vol. 217, pp. 475-476. E. I. duPont deNemours and Co., 1977, Blasters' Handbook, 175th Anniversary Edition, Dupont, Wilmington, DE, pp. 233. Tansey, D.O., 1979, "The DuPont Sequential Blasting System," CIM Bulletin, Vol. 72, July, p. 80. Thompson, S.D., 1981, "Critical Review and Revision of Surface Blasting Practice," MS thesis, West Virginia University, pp. 308-316.

Jan 1, 1986

By C. E. Webber

The economical recovery of the valuable constituents from the effluent of gas-con-densate wells has developed into a problem of balancing the cost of recovery against the cost of compressing the residual gas back into the formation. A possible method of extracting the gasoline and distillate from the natural gas is by oil absorption at high pressures. In order to design and evaluate an absorption plant, fundamental data on the composition of the coexisting hydro- carbon vapor and liquid phases at various temperatures and pressures are essential. A review of the literature indicated that the necessary data for the design of such plants are lacking. The nearest approach to desired published data is that of Katz and Hackmuth,~ who experimentally deter-mined the composition of the coexisting vapor and liquid phases in a natural gas-crude oil system at pressures up to 3000 lb. per sq. in. and at temperatures from 40' to zoo°F. This paper presents the results of the experimental determination of the equilib-rium distribution of the hydrocarbons methane through hexane between natural gas and a typical absorber oil. The ranges of temperature and pressure chosen were from 33' to r8oUF. and from 100 to 5000 lb. per sq. inch. Materials The absorber oil was a typical naturally occurring, Straw-colored distillate that had previously been steam-distilled to an initial boiling point of 300 F. The physical and chemical properties, including the results of an Engler distillation, are presented in Table I. A large volume of this oil was obtained and it was used throughout the complete set of experiments. Table i.—Properties of the Absorption Oil Gravity .......................... . . 32.5' A.P.1. Molecular weight by benzene freezing- point depression.................. 183 Viscosity, poises; at 100°F........... 0.0a80 At 200°F...................... 0.0102 Composition, PeR Cent Aromatics........ 24.0 Naphthenes..... 36.7 unsaturates,Aromatics...... .I24.00.3 1 Parafins Naphthenes.....36.7 39.o EngLeR Distillation Per Cent /ncg. F. Per Cent Dez. P. Initial boilins rmint.. 300 I 60....... 523 5.................. 402 I 70....... 538 10.................. 421 180....... 557 20.................. 462 90....... 570 30.................. 480 1 95....... 623 40.................. 49 .................1 511 Residue, z .o per cent; loss, 0.3 per cent. See refrence I. The n-hexane was obtained from the Ohio Chemical and Manufacturing Co., Cleveland, Ohio. This liquid had a boiling range of from 149" to 152.6'F., with a density of 0.667 at 60°F. and a molecular weight of 85 by benzene freezing-point depression. The propane, isobutane, wbu-tane, isopentane and n-pentane were ob-ta,ined from the Philgas Department of the Phillips Petroleum Co. Certified analyses of these compounds showed their purity to be in excess of 99.5 per cent and they were riot further purified.

Jan 1, 1941

By C. E. Webber

The economical recovery of the valuable constituents from the effluent of gas-con-densate wells has developed into a problem of balancing the cost of recovery against the cost of compressing the residual gas back into the formation. A possible method of extracting the gasoline and distillate from the natural gas is by oil absorption at high pressures. In order to design and evaluate an absorption plant, fundamental data on the composition of the coexisting hydro- carbon vapor and liquid phases at various temperatures and pressures are essential. A review of the literature indicated that the necessary data for the design of such plants are lacking. The nearest approach to desired published data is that of Katz and Hackmuth,~ who experimentally deter-mined the composition of the coexisting vapor and liquid phases in a natural gas-crude oil system at pressures up to 3000 lb. per sq. in. and at temperatures from 40' to zoo°F. This paper presents the results of the experimental determination of the equilib-rium distribution of the hydrocarbons methane through hexane between natural gas and a typical absorber oil. The ranges of temperature and pressure chosen were from 33' to r8oUF. and from 100 to 5000 lb. per sq. inch. Materials The absorber oil was a typical naturally occurring, Straw-colored distillate that had previously been steam-distilled to an initial boiling point of 300 F. The physical and chemical properties, including the results of an Engler distillation, are presented in Table I. A large volume of this oil was obtained and it was used throughout the complete set of experiments. Table i.—Properties of the Absorption Oil Gravity .......................... . . 32.5' A.P.1. Molecular weight by benzene freezing- point depression.................. 183 Viscosity, poises; at 100°F........... 0.0a80 At 200°F...................... 0.0102 Composition, PeR Cent Aromatics........ 24.0 Naphthenes..... 36.7 unsaturates,Aromatics...... .I24.00.3 1 Parafins Naphthenes.....36.7 39.o EngLeR Distillation Per Cent /ncg. F. Per Cent Dez. P. Initial boilins rmint.. 300 I 60....... 523 5.................. 402 I 70....... 538 10.................. 421 180....... 557 20.................. 462 90....... 570 30.................. 480 1 95....... 623 40.................. 49 .................1 511 Residue, z .o per cent; loss, 0.3 per cent. See refrence I. The n-hexane was obtained from the Ohio Chemical and Manufacturing Co., Cleveland, Ohio. This liquid had a boiling range of from 149" to 152.6'F., with a density of 0.667 at 60°F. and a molecular weight of 85 by benzene freezing-point depression. The propane, isobutane, wbu-tane, isopentane and n-pentane were ob-ta,ined from the Philgas Department of the Phillips Petroleum Co. Certified analyses of these compounds showed their purity to be in excess of 99.5 per cent and they were riot further purified.

Jan 1, 1941

By Robert P. Burrows

In preparing this paper the object has been to set forth facts relating to illumination problems, which, judging from the results realized in the iron and steel and other industries somewhat similar to mining, will tend toward furthering safety, production, and contentment of employees, as well as economy of operation in mines. By applying the principles of illumination with the assistance of modern appliances, the full benefits in efficiency may be derived from improvements already made in other details of mine operation. The lighting of a typical coal mine may be*divided into four distinct parts: 1, The lighting of the buildings about the top; 2, the lighting of the working faces; 3, general illumination at the bottom; and 4, special applications of lighting. The lighting of buildings about the top may be treated in the same manner as that of any other industrial plant, for we have a boiler room, an engine and generator room, a forge, a machine shop, and a hoist room. These can be well and efficiently lighted by the use of 100-watt tungsten-filament multiple lamps with proper reflectors so spaced and suspended that a power consumption of from ¼ watt per square foot in the boiler room to 1 watt per square foot in the machine shop is obtained. The methods that apply to this kind of lighting have been ably treated by a number of authors,' and for this reason a detailed discussion is unnecessary. The lighting of the working faces is usually done by means of portable lamps, of which there are four types in use: The oil torch, the acetylene Iamp, and the oil and the electric safety lamps. The different types have been fully described in numerous papers and articles and will not be covered here, although a few figures on the cost of operation will no doubt be

Jan 1, 1916

By H. G. Doll

A new electrical logging method called Laterolog is described which provides for better recording of formation resistivity. In this method a current, preferably of constant intensity, is forced into the formation perpendicularly to the wall of the hole as a sheet of predetermined thickness by means of a special electrode arrangement and of an autonlatic control system. The essential advantages of the Laterolog over the regular resistivity logs are explained. With the Laterolog, the mud column has much less influence than with conventional methods. The Laterolog is, therefore. particularly useful in wells drilled with highly conductive mud. Moreover. when the electrode system is located opposite a bed of moderate or small thickness, the disturbing effect of the adjacent formations becomes practically eliminated, provided the bed is thicker than the sheet of current. which itself is usually a few inches to a few feet thick. The sequences of beds are. therefore, much more sharply differentiated, and, in many cases, it is possible to read directly from the logs values close to the true resistivities of the formations without further corrections. Field examples are shown to illustrate the results of the method in various types of formations. INTRODUCTION As soon as it was introduced into the petroleum industry, electrical logging roved to be a powerful instrument for the delineation of the strata traversed by bore holes and for correlation of such strata." Research and engineering efforts were mostly devoted at this early time to the design of the techniqurs which could provide the best data for these purpoes. Later, attention was directed toward the quantitative analy5i.s of electrical logs, in order to obtain information on. reservoir characteristics, and, in particular, on oil and water saturation.3,4 Efforts have been made, accordingly, with a view to improving the already existing methods, or to finding new methods which could satisfy these new requirements." Quantitative analysis implies a determination as accurate as possible of the true resistivity of the formations. In fact, however; the "apparent resistivity" recorded in front of a given bed by a conventional electrical logging method is frequently quite different from the true resistivity of this bed. This is due to the combined influence of the mud column, of the adjacent formations both above and below the bed, and of the invaded zone, in which the original fluid has been more or less replaced by mud filtrate. When the beds are thick enough, and, as is frequently the case in sand and shale formations, when their resistivity is not much greater than that of the mud, it is generally possible to obtain their true resistivity directly on the electric log, or at least to obtain an approximate value which can be corrected without undue difficulty by means of recently published charts known as "departure curves."" When the beds are thin, and particularly when, in addition. their resistivity is substantially greater than that of the mud column, the apparent resistivities recorded on conventional logs are seriously affected, and it is generally very difficult, if at all possible, to estimate their true resistivity with a good enough accuracy. In the most severe cases, such as are encountered in holes drilled through hard formations with muds of high salinity, the conventional logs are so distorted and rounded that they do not even show clearly the houndaries of the different beds. In order to overcome the effect of the mud column and of the adjacent formations, it is possible to make use of appro. priate systems whereby the measurements involve a comp3ratjvelv thin slice of space at the level of the measuring device. A mention is due, in this respect, to a measuring system. called the "guarded electrode;" invented by C. Schlumberger over 20 years ago. The system, schematically represented in

Jan 1, 1951

By H. G. Doll

A new electrical logging method called Laterolog is described which provides for better recording of formation resistivity. In this method a current, preferably of constant intensity, is forced into the formation perpendicularly to the wall of the hole as a sheet of predetermined thickness by means of a special electrode arrangement and of an autonlatic control system. The essential advantages of the Laterolog over the regular resistivity logs are explained. With the Laterolog, the mud column has much less influence than with conventional methods. The Laterolog is, therefore. particularly useful in wells drilled with highly conductive mud. Moreover. when the electrode system is located opposite a bed of moderate or small thickness, the disturbing effect of the adjacent formations becomes practically eliminated, provided the bed is thicker than the sheet of current. which itself is usually a few inches to a few feet thick. The sequences of beds are. therefore, much more sharply differentiated, and, in many cases, it is possible to read directly from the logs values close to the true resistivities of the formations without further corrections. Field examples are shown to illustrate the results of the method in various types of formations. INTRODUCTION As soon as it was introduced into the petroleum industry, electrical logging roved to be a powerful instrument for the delineation of the strata traversed by bore holes and for correlation of such strata." Research and engineering efforts were mostly devoted at this early time to the design of the techniqurs which could provide the best data for these purpoes. Later, attention was directed toward the quantitative analy5i.s of electrical logs, in order to obtain information on. reservoir characteristics, and, in particular, on oil and water saturation.3,4 Efforts have been made, accordingly, with a view to improving the already existing methods, or to finding new methods which could satisfy these new requirements." Quantitative analysis implies a determination as accurate as possible of the true resistivity of the formations. In fact, however; the "apparent resistivity" recorded in front of a given bed by a conventional electrical logging method is frequently quite different from the true resistivity of this bed. This is due to the combined influence of the mud column, of the adjacent formations both above and below the bed, and of the invaded zone, in which the original fluid has been more or less replaced by mud filtrate. When the beds are thick enough, and, as is frequently the case in sand and shale formations, when their resistivity is not much greater than that of the mud, it is generally possible to obtain their true resistivity directly on the electric log, or at least to obtain an approximate value which can be corrected without undue difficulty by means of recently published charts known as "departure curves."" When the beds are thin, and particularly when, in addition. their resistivity is substantially greater than that of the mud column, the apparent resistivities recorded on conventional logs are seriously affected, and it is generally very difficult, if at all possible, to estimate their true resistivity with a good enough accuracy. In the most severe cases, such as are encountered in holes drilled through hard formations with muds of high salinity, the conventional logs are so distorted and rounded that they do not even show clearly the houndaries of the different beds. In order to overcome the effect of the mud column and of the adjacent formations, it is possible to make use of appro. priate systems whereby the measurements involve a comp3ratjvelv thin slice of space at the level of the measuring device. A mention is due, in this respect, to a measuring system. called the "guarded electrode;" invented by C. Schlumberger over 20 years ago. The system, schematically represented in

Jan 1, 1951

By G. R. Love, C. C. Koch

The changes in superconducting properties with aging time have been studied ,for the pecipitation reaction in a Tc-30 at. pct V alloy. Superconducting critical temperature, upper critical field, and relative critical current density were determined by ac susceptibility techniques. Aging produces changes in critical temperature of both matrix and precipitate which can be rationalized by compositional effects. maximum flux pinning (critical current density) occurs at a time during aging when subgrain boundaries are completely decorated with precipitates and the subgrain centers remain precipitate -free. The particular effectiveness as barriers to flux motion of planar defects which enclose regions of low deject density is discussed. THE precipitation of a second phase can dramatically modify the superconducting properties of type I1 super-conductors. According to Livingston and Schadler1 one might expect changes in the primary, secondary, and tertiary superconducting properties of the material. Changes in matrix chemistry caused by precipitation can alter the fundamental superconducting parameters; critical temperature, Tc, and thermody-namic critical field, Hc. The concimitant changes in electron mean free path (reflected in normal state resistivity) can affect the critical fields Hc 1, IIc2, Hc3. Finally, the presence of precipitate particles may hinder the motion of flux lines and may considerably improve the current-carrying capacity in high-field superconductors. The influence of precipitation on superconducting properties has been studied in a number of systems.2 Magnetization measurements have been used to study the influence of precipitates on flux pinning in lead-base alloys by Livingston3 and Evetts et al4 In these alloys precipitates induced magnetic hysteresis and flux trapping. The amount of hysteresis increased with the volume fraction of precipitate and decreased with coarsening of the precipitate. Jn an Al-Zn alloy5 and an A1-Ag alloy6 the initial precipitate size was presumably smaller than a coherence length and coarsening increased magnetic hysteresis5 and critical current density.6 The influence of precipitation on superconducting properties has also been studied in several of the commercially interesting Ti-Nb7-10 and zr-Nb11 alloys. The maximum in critical current density for these alloys was confined to a narrow range of either isothermal aging time" or isochronal aging temperature7 during the precipitation reaction. Thus, experimental evidence and theoretical considerations suggest there is an optimum precipitate size, spacing, and density, and a critical composition with respect to the matrix for flux pinning. What these "optimum" values might be and the relative importance of each is still not clear, although a few generalizations can be made. It is generally accepted1' that particle sizes smaller than the coherence length or larger than the inter-flux line spacing are poor pinning centers. In high Hc2 materials, precipitate sizes for maximum values of critical current density lie in the range of 50 to 2000Å,9,7 and there are indications that increasing dissimilarity between precipitate and matrix produces increasing pinning force.13 Because of several interesting features of the aging reaction in a Tc-30 pct V alloy, we have chosen to study the influence of precipitation on the superconducting properties of this alloy. The physical metallurgy14 and a survey of the superconducting properties" of the Tc-V alloy system have been reported. The Tc-V phase diagram is presented in Fig. 1. At 1500°C the Tc-30 pct V alloy is in the single phase 6 field. Samples quenched from the 6-phase field have a CsCl structure X-ray diffraction pattern at room temperature and it has been proposed that the 6 structure is closely related to the bcc lattice.14 When held isothermally below the eutectoid temperature, 115O°C, the 6 phase decomposes into the CsCl and hcp phases.

Jan 1, 1970

By K. Mukherjee

Instantaneous resistance change during martensitic transformation in Fe-30 at. pct Ni alloy has been studied using a low-noise electronic system. The smallest signals recorded in this investigation were of the order of 10 pv. These small signals did not show the initial increase reported by earlier investigators to support a double shear mechanism.&apos; A variety of pulse shapes and sizes was observed during "burst" transformations, and these signals were neither a linear function of the size of martensite plates nor of the volume fraction transformed. Even the smallest signals, presumably from single plates, showed complications resulting from elastic and/or plastic deformation, shock wave propagation, and so forth, which are inherent in the growth process of a martensite plate. The time of formation and interface velocity determined froni this experiment agree very well with the pioneering work of Bunshalz and Mehl.&apos; AN Fe-30 at. pct Ni (c0.005 pct C) alloy was used to study the time of formation of martensite plates. Martensitic transformations, unlike the nucleation and growth processes, are usually characterized by an extremely fast reaction rate. During the transformation, the crystal structure changes and this change is propagated through a finite volume of the parent crystal lattice within a very short time interval. The interface between the two phases probably consists of moving dislocations, and the time of formation of the plate depends on how fast this dislocation interface can move. Knapp and Dehlin~er or Cottrell and Bilby mechanisms, or similar dislocation models, can be used to calculate the time of formation of a martensite plate of a given size. In the past, conventional photographic technique475 as well as electrical resistivity techniques"~-" have been used to measure the time of formation of a martensite plate. The specific resistance of the martensitic phase in Fe-30 at. pct Ni alloy is lower than that of the austenite phase. Therefore if a current is passed through a small austenite sample in series with a large external resistance, then one would observe a voltage change across the sample as martensite is formed. Such dc measurements are shown in Fig. 1. The initial large voltage drop in Fig. 1, at the M, temperature, is due to a "burst" transformation where a large number of plates are formed in a cataclysmic manner within a very short interval of time. Even during the later stages of transformation as shown in Fig. 1, one can observe discontinuous voltage changes due to small bursts. In order to resolve the time scale of such discontinuous stages, the voltage signals are amplified and fed into a highspeed oscilloscope. In this investigation a low-noise amplifier was used for the first stage of amplification. The signal to noise ratio was further improved by the design of a pulse transformer. This transformer was capable of amplifying the signal by a factor of six. Voltage signals were studied over a wide time scale ranging from 2 sec to 0.1 psec. I) EXPERIMENTAL PROCEDURE A) Specimen Preparation. Specimens were cut from induction-melted Fe-30 at. pct Ni (<0.005C) alloy and cold-rolled to 0.2 by 1 mm cross section and an average length of 5 cm. During mechanical shaping, the specimens were strain-annealed at 950°C for 24 hr in vacuum. Finally the finished samples were vacuum-annealed at 1000°C for 6 hr and water-quenched to room temperature. The average grain diameter was 0.02 cm. B) Cooling System. The M, temperature of the alloy was -55°C. Fig. 2 shows the arrangement which was used to cool the specimen at a slow rate. The specimens were mounted inside a i -in.-diam hole in the 2-in.-long section of the copper specimen holder. This cavity was filled with silica gel. A dummy specimen was used under identical conditions for

Jan 1, 1969