Search Documents

By Zdzislaw Specht

This paper discusses elementary laws pertaining to seismic reflection methods and presents a general and simple criterion for determining the direction of dipping of a reflection horizon from observational data of distance and time. The important development of practical geophysics and the successful results obtained in America, Germany, and other countries, caused introduction of geophysical methods of prospecting in Poland. Of all methods, seismic prospecting has proved most successful in the area of the Carpathian foreland, where new oil reserves are to be expected. Because of the great depth of the sedimentary column in that area, ranging sometimes over 2000 meters, it was obvious that only the seismic reflection method could give reliable information regarding the structural features of these strata at such a depth. During the experimental surveys it appeared that the complicated geological conditions of that area do not always allow prediction of the depth and the angle of dipping of reflecting horizons, and for that reason information about the inclination of a given horizon has great importance in the determination of subsurface structure. Therefore the problem arises of obtaining from seismic reflection data reliable information as to the direction of dipping of reflecting strata, without any previous knowledge of the average velocity and depth of geologic horizons under consideration. Reflection Seismograms The earth, being a nonhomogeneous medium, is composed of a series of layers, which differ from each other in their physical properties, particularly in their elastic coefficients. These variations in elasticity are the cause of refraction and reflection of a seismic wave. Under the simple but only approximately correct assumption of the straight-line path or an elementary elastic disturbance, the phenomena mentioned

Jan 1, 1940

By Oliver Bowles

When a new type of equipment revolutionizes methods of quarrying one kind of stone, producers of other kinds focus their attention on its potentialities in their particular fields. The purpose of this paper is to discuss the accomplishments of the wire saw in slate, to show its more limited attainments in other kinds of stone, and to point out the possibilities of much wider application. A wire saw consists of a 3/16-in. or ji-in. three-strand wire cable that runs as a belt and cuts the rock by abrasion. (Fig. 1. The teeth of the saw are sand grains carried in the grooves between the strands. Accomplishments in Slate† Initial experiments with wire saws by the U. S. Bureau of Mines in the Colonial Slate Quarry, Wind Gap, Pa., in 1926, attained success so immediate and pronounced that within two years in virtually every quarry in the neighborhood of Wind Gap, Pen Argyl and Bangor, the most productive slate area in the United States, wire saws were substituted for channeling machines. An 80-ft. cut in slate is shown in Fig. 2. The technique of operation has been described in several reports (references at the end of the paper). The present purpose is to summarize the accomplishments in a large, typical slate quarry after nine. years of experience. Parsons Bros. Slate Co., at Pen Argyl, Pa., substituted two wire saws for six channeling machines in 1927. The following comparisons are made between the present method with wire saws and the former channel-ing-machine method. Rate of Sawing.—The average rate of cutting with a wire saw in the early days of its operation, as determined by the Bureau of Mines', wits 14 to 17 sq. ft. per hour. Parsons Bros. Slate Co. estimates the present rate of cutting at about 25 sq. ft. an hour, whereas the channeling-rnarhirle

Jan 1, 1938

By Oliver Bowles

When a new type of equipment revolutionizes methods of quarrying one kind of stone, producers of other kinds focus their attention on its potentialities in their particular fields. The purpose of this paper is to discuss the accomplishments of the wire saw in slate, to show its more limited attainments in other kinds of stone, and to point out the possibilities of much wider application. A wire saw consists of a 3/16-in. or ji-in. three-strand wire cable that runs as a belt and cuts the rock by abrasion. (Fig. 1. The teeth of the saw are sand grains carried in the grooves between the strands. Accomplishments in Slate† Initial experiments with wire saws by the U. S. Bureau of Mines in the Colonial Slate Quarry, Wind Gap, Pa., in 1926, attained success so immediate and pronounced that within two years in virtually every quarry in the neighborhood of Wind Gap, Pen Argyl and Bangor, the most productive slate area in the United States, wire saws were substituted for channeling machines. An 80-ft. cut in slate is shown in Fig. 2. The technique of operation has been described in several reports (references at the end of the paper). The present purpose is to summarize the accomplishments in a large, typical slate quarry after nine. years of experience. Parsons Bros. Slate Co., at Pen Argyl, Pa., substituted two wire saws for six channeling machines in 1927. The following comparisons are made between the present method with wire saws and the former channel-ing-machine method. Rate of Sawing.—The average rate of cutting with a wire saw in the early days of its operation, as determined by the Bureau of Mines', wits 14 to 17 sq. ft. per hour. Parsons Bros. Slate Co. estimates the present rate of cutting at about 25 sq. ft. an hour, whereas the channeling-rnarhirle

Jan 1, 1938

By L. L. Gray, D. W. Reed, F. Morgan

A flowMeter has been developed at Gulf Research and Development Co. and tested in the field for measuring the flow of gas in well bores. It has been used in a study of the injection capacity of different horizons in gas injection wells in Oklahoma. The flow sensitive element of the meter is a semi-conductor having a very high temperature coefficient of resistance. Advantages possessed by this meter are the result of that property and the high specific resistance of the element. The instrument possesses a sensitivity considerably higher than any reported previously. In the application described here the element is heated to a temperature considerably above ambient by an electric current, which is supplied by a voltage source at the surface. When fluid flows through the meter the rate of dissipation of heat is increased and the temperature of the element decreases. Because of the negative temperature characteristics of the resistance element such a decrease of temperature will be accompanied by an increase of resistance which, under flow conditions ordinarily found in wells, is of such a magnitude that it can be directly measured or recorded in terms of a change in voltage at the surface. In practice, rate of flow is measured in terms of the drop in voltage in the resistance element. All the metering and control apparatus remains at the surface while the thermal element is lowered into the well on a single conductor cable, consisting of an insulated wire and sheath. The meter is calibrated by passing known quantities of gas through it either at the surface or in the hole at a point immediately above the region in which gas is lost to the formation. In case calibration is made at the surface, the ambient temperature in the hole may readily be obtained by a second resistance element which is operated at a current so low that effectively no heating occurs. The instrument has been adapted to con-tinuous recording, but the velocity of the meter relative to that of the gas must be low unless corrections are made. Curves giving data obtained in actual field tests are shown' The meter can also be used to determine the distribution of flow capacity in a gas producing well. A differential form of the meter has been designed and built in which the local flow or injection capacity of the formation is obtained directly. Introduction When fluid is injected into a well in a secondary recovery or pressure-maintenance operation the question of its most effective use invariably arises. Although the core log, when available, will show the regions of good permeability and oil saturation, there is normally no assurance that the fluid actually enters the formation in zones where injection is deemed desirable. In view of the uncertainties involved in such programs, it is generally conceded that measurements of permeability for a formation in place are more significant than those obtained by the core-sampling technique. A subsurface meter has been developed at the Gulf Research and Development Co. for measuring flow of fluids at different horizons in a well bore, and field tests have been made on the instrument in Cooperation with the Tulsa Division of the Gulf Oil Corp. In this paper the meter is de-

Jan 1, 1948

By F. Morgan, L. L. Gray, D. W. Reed

A flowMeter has been developed at Gulf Research and Development Co. and tested in the field for measuring the flow of gas in well bores. It has been used in a study of the injection capacity of different horizons in gas injection wells in Oklahoma. The flow sensitive element of the meter is a semi-conductor having a very high temperature coefficient of resistance. Advantages possessed by this meter are the result of that property and the high specific resistance of the element. The instrument possesses a sensitivity considerably higher than any reported previously. In the application described here the element is heated to a temperature considerably above ambient by an electric current, which is supplied by a voltage source at the surface. When fluid flows through the meter the rate of dissipation of heat is increased and the temperature of the element decreases. Because of the negative temperature characteristics of the resistance element such a decrease of temperature will be accompanied by an increase of resistance which, under flow conditions ordinarily found in wells, is of such a magnitude that it can be directly measured or recorded in terms of a change in voltage at the surface. In practice, rate of flow is measured in terms of the drop in voltage in the resistance element. All the metering and control apparatus remains at the surface while the thermal element is lowered into the well on a single conductor cable, consisting of an insulated wire and sheath. The meter is calibrated by passing known quantities of gas through it either at the surface or in the hole at a point immediately above the region in which gas is lost to the formation. In case calibration is made at the surface, the ambient temperature in the hole may readily be obtained by a second resistance element which is operated at a current so low that effectively no heating occurs. The instrument has been adapted to con-tinuous recording, but the velocity of the meter relative to that of the gas must be low unless corrections are made. Curves giving data obtained in actual field tests are shown' The meter can also be used to determine the distribution of flow capacity in a gas producing well. A differential form of the meter has been designed and built in which the local flow or injection capacity of the formation is obtained directly. Introduction When fluid is injected into a well in a secondary recovery or pressure-maintenance operation the question of its most effective use invariably arises. Although the core log, when available, will show the regions of good permeability and oil saturation, there is normally no assurance that the fluid actually enters the formation in zones where injection is deemed desirable. In view of the uncertainties involved in such programs, it is generally conceded that measurements of permeability for a formation in place are more significant than those obtained by the core-sampling technique. A subsurface meter has been developed at the Gulf Research and Development Co. for measuring flow of fluids at different horizons in a well bore, and field tests have been made on the instrument in Cooperation with the Tulsa Division of the Gulf Oil Corp. In this paper the meter is de-

Jan 1, 1948

By Sidney H. Haughton

WHEN the white pioneers of the eighteenth and nineteenth centuries advanced from the coastal settlements of southern Africa into the interior of the subcontinent, they found it inhabited, more or less sparsely, by brown or black peoples mainly of pastoral habits but equipped with a fighting spirit and certain fighting weapons. Some of the tribes were smiths, others were miners and metallurgists; all used fuel, either industrially or domestically. Some of that fuel was wood, some cattle dung, and in some places the natives mined outcrop coal. Coal was first discovered by Europeans in Natal about 1840. After proper deliberation and after allowing due time for a consideration of all the implications, the Natal Government decided in 1881 (40 years after) to import an English expert to investigate and report on the discovery. Things then moved rapidly, and in what to a geologist is the remarkably short space of eight years, Natal collieries were producing at the rate of nearly 30,000 long tons per annum or 100 long tons per working day!

Jan 1, 1945

By E. L. Kapfer

A preliminary description is made of the field of automation and optimization of the oxygen blast furnace process. The concept of static and dynamic process control is illustrated. After a short general description of all factors concerning the optimization of this process, a learning system is derived which gives better results than models previously used. This learning or self-adaptive control system uses statistical methods with exponential aging of process data and requires derivation of multi-variable functions of the process for which measurements can be made available. The practical application of this new procedure and of additional measuring instruments are discussed, and results obtained in plants using the adaptive control system are described. A survey of European steel plant automation using the Siemens technique is presented.

Jan 1, 1969

By L. G. Schulz

THE possibility of using reflected X-rays to produce images of crystals was explored by Barrettl who developed simple experimental procedures for X-ray microscopy and who showed by numerous examples the great range of information that could be made available. In his method characteris radiation is used to produce an image of a limited area of the sample on fine-grained film, this image subsequently being enlarged approximately X100. A somewhat different method will be described here;' white radiation from a fine-focus X-ray tube-"' is used to produce an image of a relatively large area of a single-crystal surface. part of the sample; therefore, white radiation is needed. The resolution in the image formed on the photographic film will depend on the size of the focal spot of the X-ray tube. If the sample is made

Jan 1, 1955

By Richard R. Parizek, E. Scott Blair

Numerical modeling of ground water flow systems can be used to help analyze many practical problems encountered in the mining industry. Numerical models can be used to predict ground-water seepage rates into surface mines, shafts, and other large excavations; to predict water-level changes under adjacent properties; and to predict the effectiveness of various deep-well dewatering schemes. As with any model, the results from a numerical model are limited by the quality and quantity of data, and by the restrictions of any simplifying assumptions. A case study is presented that shows how a numerical model was used for engineering purposes to help analyze the hydrologic impact of a proposed open-pit mine by Predicting changes in the dewatering rate caused by the lateral growth and deepening of the mine and by predicting the effectiveness of various deep-well dewatering schemes.

Jan 1, 1982

By Oscar Aguilar, Jin-ichi Nakamura, Kazuo Nakamura

Michiquillay deposit is porphyry copper type with over 500 million tons of 0.70% Cu ore. In order to reflect the true nature of the orebody as to shape and value distribution and to compensate for insufficient data in the outer perimeter and lower portion, "Triangular Interpolation Method" is used in the computation, wherein block grades are determined by "Plane Regression". The results thus obtained are compared with the data from additional investigation and are found to match well with each other. Aside of total Cu, assays of Fe, S, MoS2 and geological data such as alterations, rock types, faults, mineralogical compositions are also stored in the computer. By this system, their distribution and relation to alteration become clear and classification of ore into types affecting recovery become possible. The outputs of this system make clear the characteristics of the orebody and furnish valuable geological data on the orebody.

Jan 1, 1976

Since I have had the pleasure of watching the development of this process very closely, I feel that I ought to say a few words on the subject, although I cannot add much to what Mr. Roe has already said. I wish, however, to bear witness to the hard work, persistence and skill which have been exercised during the past two years, and which have so well deserved the success attained. Those of us who remember the history of the past efforts in this line, such as the rotary puddlers, in which also some of us had a part, can easily appreciate the problems involved, and may well be skeptical as to the outcome. Such, at least, was my frame of mind when the process first came under my notice. Now, after having seen every heat, but three, of the many made, it really seems to me that a process and plant for the mechanical puddling of iron has at last been developed which is practical, economical and successful. Of course I do not mean by this that either the process or the machines are developed to their highest point, technically or economically, but that, in my opinion, these goals are in plain view, and that the difficulties which remain are such as will be overcome by developing the skill of the operator through practice ;

Jan 1, 1903

By William Newton Best

Oil burners, oil furnaces, and methods of installation, have been the subject of many articles, but information concerning oil-burning systems, based upon scientific principles, is still in great demand, especially in the manufacturing districts of our country. Fuel oil, as it is termed (this being the residuum from oil refineries), has for many years been of great service to our manufacturers, and has justified its popularity not only by producing a superior manufactured product, but by turning out approximately 50 per cent. more product than can be made with coa1 fuel under like conditions. To install a system requiring only an oil-storage tank, a small pump, and an oil-supply main with numerous laterals leading to the various burners, furnaces, boilers, etc., is a comparatively simple matter; and, because fuel oil is very volatile, it is not necessary to heat it, even during the winter months in a very cold climate. Furthermore, only a small amount of power is required to atomize fuel oil, this often being done by a positive pressure blower, or by a mechanical burner. An analysis of fuel oil, together with that of various other liquid fuels, is given in Table I.

Jan 1, 1915

By George E. Moore, B. K. Miller

The Missouri fire clays are here divided into plastic and semiplastic clays occurring as widespread bedded deposits in east central Missouri and flint and diaspore clays occurring as isolated "sink-hole" deposits in the north central Ozark region. Visual inspection was the first method used in clay prospecting. Thin overburden, hard sandstone "rimrocks," and the occurrence of diaspore float made this method particularly applicable in the flint and diaspore fields. The first drilling tool used was a hand auger. One man can drill 25 to 50 ft. per day at a cost of about 35 cents per foot. Holes can be drilled to a depth of 150 feet. Spud drills are often used where the overburden is hard. This drill uses a slotted earth socket bit. A two-man crew can drill about 100 ft. per day at a cost of about 35 cents per foot. Mechanically powered auger drills have been used extensively in wildcat drilling in the past few years. This type of drill furnishes a continuous set of cuttings. The practical depth limit with this drill is 50 to 60 ft. Two men can drill 300 ft. per day at a cost of about 20 cents per foot. Core drilling is used mainly to prove a known 'lay deposit. A A crew with a No. 22 Sullivan drill can drill about 30 to 40 ft. per day in soft clay, at a cost of about $1.25 per foot. Introduction Because of the geological variations in the Occurrence of the several types of fire clay mined in Missouri, it is necessary, when discussing the prospecting methods used for discovering and proving these clays, to divide these operations into two classes, one including plastic and semi-plastic fire clays, the other flint and diaspore clays. The plastic and semiplastic fire clays in the east central and St. Louis districts are generally classified as Cheltenham clays. This formation is a more or less continuous deposit and is found Over a large area in east central Missouri. There are variations, however, in the quality and thickness of the clay, which necessitate detailed prospecting in order to determine deposits of economic value. The nature of the overburden (Fig. 1), which consists of Pennsylvanian limestone and shale beds of varying thicknesses, and a mantle of glacial drift, regu1ates the methods and equipment used in prospecting for these clays. The district in which these clays occur is a gently rolling upland region, characteristic of most of northern Missouri. Along the southern fringe of this area there are numerous deposits of flint clay lying as masses or lenses in depressions at the base of the continuous and widespread Cheltenham formation, or as outlying "sink-hole" deposits in the area marginal to that formation. South of the Missouri River in the north central Ozark region, there are high-grade flint and high-alumina clays, commonly referred to as burley and diaspore clays in sink-hole type deposits. The overburden On these deposits is thin, consisting chiefly of soil and hard-pan, which varies from a plastic

Jan 1, 1948

By B. K. Miller, George E. Moore

The Missouri fire clays are here divided into plastic and semiplastic clays occurring as widespread bedded deposits in east central Missouri and flint and diaspore clays occurring as isolated "sink-hole" deposits in the north central Ozark region. Visual inspection was the first method used in clay prospecting. Thin overburden, hard sandstone "rimrocks," and the occurrence of diaspore float made this method particularly applicable in the flint and diaspore fields. The first drilling tool used was a hand auger. One man can drill 25 to 50 ft. per day at a cost of about 35 cents per foot. Holes can be drilled to a depth of 150 feet. Spud drills are often used where the overburden is hard. This drill uses a slotted earth socket bit. A two-man crew can drill about 100 ft. per day at a cost of about 35 cents per foot. Mechanically powered auger drills have been used extensively in wildcat drilling in the past few years. This type of drill furnishes a continuous set of cuttings. The practical depth limit with this drill is 50 to 60 ft. Two men can drill 300 ft. per day at a cost of about 20 cents per foot. Core drilling is used mainly to prove a known 'lay deposit. A A crew with a No. 22 Sullivan drill can drill about 30 to 40 ft. per day in soft clay, at a cost of about $1.25 per foot. Introduction Because of the geological variations in the Occurrence of the several types of fire clay mined in Missouri, it is necessary, when discussing the prospecting methods used for discovering and proving these clays, to divide these operations into two classes, one including plastic and semi-plastic fire clays, the other flint and diaspore clays. The plastic and semiplastic fire clays in the east central and St. Louis districts are generally classified as Cheltenham clays. This formation is a more or less continuous deposit and is found Over a large area in east central Missouri. There are variations, however, in the quality and thickness of the clay, which necessitate detailed prospecting in order to determine deposits of economic value. The nature of the overburden (Fig. 1), which consists of Pennsylvanian limestone and shale beds of varying thicknesses, and a mantle of glacial drift, regu1ates the methods and equipment used in prospecting for these clays. The district in which these clays occur is a gently rolling upland region, characteristic of most of northern Missouri. Along the southern fringe of this area there are numerous deposits of flint clay lying as masses or lenses in depressions at the base of the continuous and widespread Cheltenham formation, or as outlying "sink-hole" deposits in the area marginal to that formation. South of the Missouri River in the north central Ozark region, there are high-grade flint and high-alumina clays, commonly referred to as burley and diaspore clays in sink-hole type deposits. The overburden On these deposits is thin, consisting chiefly of soil and hard-pan, which varies from a plastic

Jan 1, 1948

By AIME AIME

N EARLY 1300 members and guests crowded the halls of the Engineering Societies Building during the winter meeting of the Institute just closed, and more than 600 attended the banquet. In variety of program, quality of papers, interest in discussion, and brilliance of social features, the meeting maintained the high reputation of the past. Nothing elaborate in the way of excursions was attempted, experience having proved that February weather in New York is much too uncertain to warrant extensive field trips. A sight-seeing journey up the Hudson to the Bear Mountain bridge was, however, made despite the snows of the week before and the week after. The annual business meeting, while attended by a minority of the members in the building, was marked by the display of keen interest in the work and called out several interesting discussions. The excellent reports of the committees that had organized their work and directed it along definite lines, emphasized the need of funds with which to support assistants or Fellows who shall correlate and put to the highest use the facilities of the Institute in research along technical lines. This thought was developed at the banquet by the retiring president, J. V. W. Reynders, and it is expected that the Directors will take early steps to collect a fund for this purpose. The number of the individual sessions was too great and the papers and discussions too numerous to permit mention here of all the features of inter- est. A general review only follows. The papers and detailed discussions will be printed and sent to members as promptly as possible.

Jan 1, 1926

IF you do not make the disc at the same time as the core and as part of it, it is necessary to make it by itself. This is done by spreading on a board or other flat surface a layer of clay as thick and wide as [88] the disc that you made at the feeding head of the first pattern of the gun. When it is dry, mark it exactly with compasses and then, cutting with a chisel or rasp, make it fit exactly into the empty space at the head. Likewise, make a hole just as wide as the thickness of the core exactly in the middle of this clay disc. When you have put the disc in its place in the mould and then pass the core through this hole, it passes exactly through the center of the mould in such a way that it meets the iron ring that you put at the foot of the mould for this purpose. As I said above, if' you do not make it as part of the core, it is necessary to proceed in the aforesaid way. But if' you wish to make it attached to the core (which I like better because it can be done more accurately) make a

Jan 1, 1942

By A. Heim, M. Gondouin

Invasion experiments were run on Berea sandstone cores to get laboratory measurements of resistivity and saturation profiles characteristic of water and oil sands invaded by mud filtrate. Injection rates were as low as 1.13 cm/D, and the cores were 30 to 36 in. long, cut parallel to the bedding planes. In the water-sand case, the resistivity profiles revealed the existence of an extensive transition zone between flushed and uncontaminated zones. In the linear geometry of the experiment, the width of the transition zone increased as the square root of the injected fluid volume. For the oil-sand case the core was prepared by displacing the formation water with kerosene to minimum water saturation. During the subsequent invasion experiment. oil saturation was measured directly by means of an oil-soluble radioactive tracer, and resistivity profiles along the core were taken at the same time. These data were interpreted in terms of an oil-water front, followed by a formation water bank, a zone of mixed waters, and finally, invaded mud filtrate near the borehole. Micro-fingering and capillarity seemed to affect considerably the resistivity profiles observed in the invaded oil-sand experiment. Beyond the regular conductive annulus or "low zone", it was found that a resistive "anti-annulus" could also be formed. As a result of these experiments, some simplified invasion profiles have been accepted and are being used in Grand Slam* interpretations. INTRODUCTION The importance of the mud filtrate-invaded zone in interpreting electrical logs has long been recognized.',* In trying to account for its effect, only very simple models of the resistivity profiles in the radial direction from the borehole have been used. In fact, most log interpretation charts have been based on resistivity models consisiting of two media of uniform resistivity (R, and R,) abruptly separated at the diameter of invasion. Such a clean separation of the media of different resistivities seems unrealistic, since flushing may not be perfect and may vary with radial distance into the formation.3** The nature of the transition zone, when it is within the radius of investigation of the surveying devices, may affect the log readings. Campbell and Martin' verified that a conductive annulus containing a high percentage of formation water may be formed when mud filtrate invades an oil-bearing sand. Interpretations which are to include the effect of such an annulus require the addition to the model of a conductive zone located at the outer rim of the invaded zone.' Using the Buckley-Leverett relations,6 aturation profiles may be derived, from which resistivity profiles can be calculated. Results of such computations by K. S. Kunz and J. H. Moran were given in a paper by Dumanoir. Tixier and Martin,7 and led to the construction of log interpretation charts which were based on a representation with three media of resistivities R, R0 and R1. Fig. 1 shows a schematic representation of a resistivity profile which includes an annulus. Campbell and Martin realized that, during the invasion of an oil sand, both capillarity and mixing would contribute to rounding of the profile shown in Fig. 1. Capillarity tends to draw some of the formation water from the annulus into the uncontaminated (Rt) zone, whereas mixing of the mud filtrate with formation water of the

Jan 1, 1965

By D. L. Luffel

This paper presents two main developments: (1) a short, constantly accelerated centrifuge method of measuring drainage capillary pressure properties of cores, and (2) a new analytic method of treatment of centrifuge measurements to obtain saturation-capillary pressure relations. Toward the first objective, a clever experimental method is presented which is certainly more rapid than previous centrifuge methods. Toward the second objective, a new analytic method is derived to eliminate the approximate method of Hassler and runner. The derivation of this new analytic method, however, appears to be in error. The new analytic solution is developed as Eq. 5 in Appendix A. At the beginning of this derivation, the average wetting phase saturation of a core is expressed as, where is the centrifuge angular velocity. Eq. D1.2 makes explicit the dependence of S and S upon The second equation shown in Appendix A expresses the relation between the three variables Since for a given porous medium the saturation is uniquely related to capillary pressure, the functional dependence of S upon P is trivial, i.e., Pc.ri does not actually appear. Thus, the function 5 (r, ) may be expressed as a new function, S*, of PC, , alone The author transforms the variable of integration in Eq. Dl through use of Eq. D2 and writes

Jan 1, 1965

By George W. Maynard

(Pittsburg Meeting, March, 1910.) AT the Pittsburg meeting of the Institute, May, 1879, I made the first announcement in America of the results obtained by Sidney Gilchrist Thomas and Percy C. Gilchrist, ill their efforts to eliminate phosphorus in the manufacture of steel in the Bessemer converter and the open-hearth furnace.1 The first published statement in an American newspaper was a reprint of the first Thomas-Gilchrist paper, 2 which I sent to J. C. Bayles, at that time the editor. At the suggestion of many friends who were present at the Pittsburg meeting, and others who are cognizant of the beginnings of the process in the United States, and for the information of the younger generation of the iron and steel fraternity, I have thought it eminently proper that the history of the process in detail should be given where I made the first announcement and where the process has had its largest development. During my residence in England, from April, 1873, to February, 1879, and as a member of the Iron and Steel Institute since 1874, I was present at many of its meetings during those years. At nearly -every meeting the burden of discussion was the question of the use of pig-iron containing phosphorus in the. manufacture of steel by the Bessemer or the open-hearth process. In my biographical notice of Thomas;3 read at the New York meeting of, the Institute, February, 1885, I show that the working-out of the process was not a hap-hazard or accidental inspiration, but the culmination of many years of investigation of experiments and theories which had been carried on and advanced by chemists and metallurgists at home and abroad. 1 Trans., viii., .5 (1879-80). 2 The Iron Age, vol. 22, No. 17, p. 3 (Oct. 24, 1878). 3 Trans.. xiii., 785 to 791.

Jul 1, 1910

By T. S. Fuller

Various phases of the embrittlement of solid copper containing oxygen by the action of reducing gases at high temperatures are familiar to readers of metallurgical literature through the work of many experimenters. In 1900, Heynl recorded observations of copper being heated in hydrogen with the development of fine cracks, the result of the formation of steam within the metal through the action of hydrogen on the copper oxide usually found in copper. Archbutt,2 in 1905, published the results of experiments, showing that all oxygen can be removed from copper by heating to redness, for several hours, in hydrogen. Intercrystalline cracks and extreme brittle-ness developed. Archbutt attributed the brittleness to the reduction of oxides present in the copper. Bengough and Hil1,3 in 1910, encountered the now well-known embrittlement at the outset of their investigation and stated in their paper: It soon became evident that the effect of any heat treatment depended largely on the presence or absence of reducing gases in the atmosphere of the furnace, as well as on its temperature. Hence it became necessary to adopt a somewhat elaborate scheme of heat treatment. The authors found embrittlement in separate experiments due to both hydrogen and carbon monoxide and concluded that: "The gases ruin the alloys after being heated to about 650" C. in their presence." Ruder,4 in 1916, reported the results of a series of experiments made by heating commercial and deoxidized copper in hydrogen, carbon monoxide, carbon dioxide, and steam. In agreement with other writers, he found that copper containing oxygen was made brittle by reducing gases, while the deoxidized metal remained unaffected. In the case of

Jan 1, 1926