Search Documents

By C. F. Lucks, W. D. Wood, H. W. Deem

Electrical ad thermal-conductivity measurements have been made on titanium and 6 titanium alloys. The following expression was derived for calculating thermal conductivity from electrical conductivity: K = 0.626 s T x 10-8 + 0.00497 where K = thermal conductivity, cal sec-1 cm-2 cm0C-1 s = electrical conductivity, ohm-]cm-1 T = temperature, deg Kelvin This expression gives calculated thermal conductivities that are not in error by more than 10 pct from the experimental values for A-55 titanium and the 6 alloys measured; namely, A-110AT, C-110M, C-130AM, Ti-6A1-4V, Ti-140A, and Ti-155A, which are representative of the presently available commercial a and a-ß titanium alloys. THERMAL conduction in a gas, liquid, or amorphous solid is accomplished by energy diffusion from molecule to molecule, a relatively slow process. For this reason, such materials have a low thermal conductivity. When a material is crystalline, there is in addition a heat transfer by a vibratory motion of the crystal lattice. It is the contribution of this lattice conduction that makes a crystal a much better conductor than a gas, liquid, or amorphous solid. Lattice conduction, however, does not account for the relatively enormous thermal conductivity of a metal. This is explained by the freedom of movement of valence electrons. These valence electrons drift in a metal in a direction toward a drop in electrical potential and, to a lesser degree, in the direction of a temperature drop in the metal. Since both the electrical and thermal conductivities of a metal depend upon the presence of free electrons, there should be some relatively simple relation between the two. Wiedemann and Franz in 1653 first discovered an approximate empirical relation between the electrical and thermal conductivities of metals at the same temperature. This ratio varies appreciably with temperature, and Lorenz later showed that by adding a temperature factor to the Wiedemann-Franz ratio the value of K/(s T) is constant, where K is the thermal conductivity, a the electrical conductivity, and T the absolute temperature. This Lorenz constant shows a greater variation for alloys than it does for pure metals, the ratio increasing slightly as the proportion of alloying elements increases. It has been found that a closer correlation between electrical conductivity and thermal conductivity can be obtained by means of an equation of the form K - A s T + B [1] where A and B are constants. In this equation the term AsT is the contribution of electronic conduction and B is the contribution of lattice conduction to the total thermal conductivity. EXPERIMENTAL MEASUREMENTS Electrical-resistivity and thermal-conductivity measurements on titanium and 6 titanium alloys serve as the basis for determining an equation of the K = AsT + B type for titanium alloys. Specimens—Table I shows nominal compositions of the 7 metals on which electrical and thermal conductivities were measured. The electrical and thermal-conductivity specimens for each alloy were taken from stock of the same heat and usually from adjacent sections of the same bar. All of the metals measured were in a mill-annealed condition. Methods—Electrical-resistivity measurements

Jan 1, 1959

By W. R. Ingalls

WHAT proportion of the national wealth is represented by' the producing mines of the country?' Or by the- mining and metallurgical industry-as a whole, for it is impossible to make-an economic distinction between the mines that produce the ore and the plant that is used to get the metals from it. The total national wealth in fixed property is about $270,000,000,000. How much for the mines? I do not know that any one 'else has ever tried to furnish answers to these questions. In making such an attempt I am conscious that the result can be nothing more than a rough approximation. Yet even that will give an idea of relative values. No separate valuation for the mines of the country has appeared in any inventory of the national wealth previous to that which I compiled and published for 1916. -In earlier census estimates mines were supposed to be included under the head of real estate. However, an examination of the laws and practices of the several states with respect to mine taxation will make it evident that no good idea of the value of the mines of the coun¬try is obtainable from the assessment rolls. In my previous estimate for 1916, I computed the value of the mines at $8,000,000,000, which was approxi¬mately 10 times their net income as reported to the Bureau of Internal Revenue. In making that estimate I fell grossly into error, for several reasons that it is unnecessary to explain, but chiefly because the net income of the mines of the country in that year was exceptionally large. The whole subject of valuing the mines of the country en bloc is extraordinarily difficult At the best, no one can hope to arrive at, anything more than a rough idea about it. However, elements of reason may be introduced and may be made to serve as chief bases.

Jan 1, 1921

By DIFTIGIHT E. WOODBRIDGE

(Glen Summit Meeting, June, 1911,) DURING April, May, and June, 1910, I was in charge of an examination of the greater part of the Moa iron-ore area in Oriente Province, Cuba, on the north coast, near the east end of the island. My instructions, on arrival at the properties, were to check former estimates of tonnages and grades, and to re-examine the ore comprised in claims covering 44,727 acres. This work included .the running of lines dividing the properties into co-ordinate planes, the boring of many thousand feet of holes spaced at the intersections of these co-ordinates, the taking of samples of the ore penetrated, the analysis of these samples for their various constituent minerals, and the determination of the results as to tonnages, depths, and grades, both for individual properties and for the entire group. Each section of every one of the thousand holes drilled was to be compensated for depth and grade with every other, a series of simple arithmetical calculations of no slight magnitude, the mere mechanical labor of which consumed much time, but finally resulted in giving a complete average of all the essential facts for the entire area of 18,000 hectares. Had it not been for the more than willing, active, and able co-operation of the officers of the Spanish-American Iron Co., from Charles F. Rand, President, and Jennings S. Cox, General Manager, down to the most humble water-carrier, the work would have consumed far more time than it did. Papers prepared by others, and to which my present paper may be considered an addendum, elucidate, more fully than I could hope to do, the origin and geological character of these ores. I will confine myself to the situation, method and expense of exploration, and to probable courses of development and mining, with some attention to the cost of the ore delivered in the United States.

Mar 1, 1911

By M. G., Corson

1. In addition to the alloys of copper with iron previously found by Hanson and Ford to show an increase in the concentration of the alpha range with increase in temperature the following binary and ternary systems have been found by the author to exhibit: the same feature: (a) Copper-chromium. (b) Copper-cobalt. (c) Copper-silicon. (d) Copper-nickel-silicon and its pseudo-binary section Cu-Ni2Si (formula of compound definitely established). (e) Copper-cobalt-silicon and its pseudo-binary section Cu-Co2Si (formula of compound established with some probability but not as definitely as for Ni2Si). (f) Copper-chromium-silicon; formation of a compound definitely established (compare Figs. 1 and 2). The formula of this compound may be either Cr2Si or Cr3Si. (g) Copper-iron-silicon; presence of a phase containing both iron and silicon established in an indirect way only. No definite microconstituents observed. 2. RANGES OF SOLID SOLUBILITY (percentage at various tempera¬tures). (a) For copper-chromium: 0.8 at 1000° C.; 0.5 at 900° C.; 0.25 at 800° C.; 0.05 to 0.1 at 500° C. (b) For copper-cobalt: 3.4 at 1000'C.; 2.4 at 900'C.; 1.7 at 800'C.; 0.9 at 600°C.; 0.35 at room temperature. (c) For copper-silicon (Fig. 3) : 6.8 ± 0.1. per cent. at 800° C.; 3 per cent. at 400° C. and probably below 2 per cent. at room temperature if sufficiently long annealed. (d) For copper-cobalt silicide: 3.3 at 1000° C.; 2.4 at 900° C.; 1.6 at 800° C.; 0.7 at 600° C.; 0.3 at 300° C. (e) For copper-nickel silicide (Fig. 4): 8.2 at 1000° C.; 5.5 at 900° C.; 3.6 at 800° C.; 1.6 at 600° C.; 0.7 at 300° C.

Jan 1, 1927

By Ernst F. Eurich

(Cleveland Meeting, October, 1912.) ALEXANDER PARKES patented in England in 1851-52-53 a process for desilvering lead by means of zinc, making use of the greater affinity of silver for zinc than for lead, discovered by Karsten in 1842. The efforts in England to develop it commercially were not particularly successful, nor was the attempted introduction into the United States. This last was not surprising, as it was about the beginning of our Civil War, and at that period there was very little lead-bullion produced in the united States and there was no field for the process here. There was at that time on Staten Island an establishment that pattisonized lead, probably from Rossie, N. Y., and Chester, Pa., and possibly some Spanish lead, but the production of lead-bullion in the Far West had not yet begun. In 1864, Edward Balbach, of Newark, N. J., patented in this country a process for desilvering lead by means of zinc, and in 1867 Edward Balbach, Jr., patented a " movable black-lead retort with a neck, placed in a furnace," for the purpose of distilling the alloy of zinc, lead, and the precious metals. A brief comparison of the Parkes and the Balbach processes is interesting. The Parkes process as practiced in England consisted in stirring into silver-bearing lead, melted in a kettle, from 1 to 2 per cent. of zinc, cooling, skimming the alloy of lead, zinc, and silver that rose to the surface, liquating it in an iron retort, distilling the residual rich alloy in fire-clay retorts, thus regaining the zinc, and refining the desilvered lead at a low heat in a shallow cast-iron pan that formed the hearth of a reverberatory furnace. If the lead was too impure, it was first softened * Presented also at the Joint Meeting of the Institute and Section IIIa, Metal¬lurgy and Mining, of the Eighth International Congress of Applied Chemistry, New York, September, 1919, and here published by mutual agreement.

Dec 1, 1912

By GEORGE H. DERN

IF THE engineer is to go into politics, as I think he should, I believe the curriculum of every engineering school should be amended to include a good stiff course in public speaking. My observation has been that the engineer in private conversation can scintillate as brightly as a life insurance agent or an oil stock salesman, but before an audience, with rare exceptions, he is a total loss. He will not get up and talk. He hides his light under a bushel, and sits on the bushel as dumb as an oyster. I have seen meetings of the Utah Section at which some topic of general interest to the members was up for discussion, and where an animated debate was the logical thing to expect. After the chairman states the subject and invites discussion, there is dense silence. Finally a member, bolder than the rest, gets up and with trembling voice and knees makes a motion. The motion carries, the meeting adjourns, and then the members gather into groups and begin to discuss the question seriously -and intelligently, giving cogent arguments on either side and embellishing their remarks with appropriate or inappropriate epithets illustrations and figures of speech. Now, I am not pleading for more speechmaking. The good Lord knows we have too much of this great American indoor sport already. But I think every man ought to be able and ready to express his opinions at the proper time. Some men have a reputation for wisdom because they do not talk much. We speak of the wise old owl because she never speaks, but in my opinion the owl's reputation for wisdom is vastly overrated. silence is more apt to be a cloak for stupidity than for wisdom. The person who has ideas can- not exert any influence by keeping them locked up in his own mind. The great motive force of the world is not muscle, but ideas, and ideas in order to get in their work must be released.

Jan 1, 1925

By Charles H. White

Discussion of the paper of A. L. Sweetser, Tress., xxxviii., 236. CHARLES H. WHITE, Harvard University, Cambridge, Mass. (communication to the Secretary*) :-Those interested in leaching-processes gladly welcome contributions on either laboratory-tests, such as are reported by Mr. Sweetser, or mill-tests made on larger quantities of ore; and especially valuable are such reports, even with negative results, if the methods adopted are the outgrowth of an intimate knowledge of the conditions to be met. It seems very desirable, therefore, that as complete details as possible be given in reporting on such tests, particularly with respect to the character of the ore under examination. The questions of prime importance in the sampling of ore and in the making up of charges for laboratory-tests are those respecting its grade and uniformity. In Mr. Sweetser's paper the first of these questions is answered definitely, but the answer to the second, although apparent on inspection of the results, might be more strongly emphasized with advantage, since it is only on account of the extreme uniformity of the ore that the satisfactory results obtained could have been expected. It seems advisable to call attention to the fact that for average ores, and more particularly for uneven, or 11 spotted ores, the quantities used by Mr. Sweetser are not usually regarded as sufficient to insure satisfactory results. Let us examine the method somewhat in detail. The ore was crushed to pass a 5-mesh screen, and a sample of 45 lb. was taken out for assay and tests. The diameter of the largest grain of this ore, according to Richards,1 was 2.67 mm.-assuming here, as in the following cases, that the wire of the screen was of the largest size used for the purpose, thereby giving any possible advantage in this respect in favor of the method. The table in Richards's book, p. 852, shows that 45 lb. is a sufficient quantity for a fair sample with uniform ores, but not sufficient

Jan 7, 1908

By Edgar Rickard

E UGAR RICKARD comes of a long line of mining men and was born at Pontgibaud, France, in 1874, where his father was then in the course of his professional work. Later his father came to California and was until his death prominently connected with milling in that state and Nevada. Edgar Rickard grew up at Berkeley, attended the University of California, graduated in 1895 from the mechanical engineering course, and remained a year longer for post-graduate work in the College of Mining. His first job was as assarer for the Mountain Copper Co., Keswick, Cal., in 1896. The following year he was assayer and surveyor for the Cornucopia Mines, Oregon. In 1898, he joined the staff of the Venture Corporation, London, and for two years made examinations for them in various parts of the world. He served as mine manager at Cripple Creek and at the Briseis tin mine, in Tasmania. From 1901 to 1905, he was general manager of the Progress Mining Co. in Lower California, but when his cousin, T. A. Rickard, bought the Mining and Scientific Press he was persuaded to come to San Francisco as business manager of that periodical. A few years later the two cousins went to London and started the Mining Magewine there as a joint venture, Edgar being the business manager. In 1915, he took over control, T. A. Rickard returning to California to devote his time to the Mining u.rbd Scientific Press. In 1917 Edgar Rickard sold out to his British associates and came home to serve in the Food Administration through the war. Rickard was one of the first of the American engineers called to his staff when Herbert Hoover began his relief work by helping stranded Americans home at the be- ginning of the war and he has been with him constantly since in the Commission for Relief in Belgium, the

Jan 1, 1929

By John M. Lovejoy

I take pleasure in transmitting herewith "Petroleum Development and Technology in 1927," in which we have attempted to set out in a series of 40 papers with attendant discussions the advances made in Production Engineering and Refinery Engineering during the year. The volume also contains a digest of round table discussions on Petroleum Engineering Research problems and Petroleum Engineering Education. In addition to the above we set out in 16 papers a review of production of each producing area of the United States and of the more important foreign countries, together with a review of the world's production and forecasts for 1928. We also include 8 papers on the Economics of the oil industry. The papers and discussions included herein represent the contributions of more than 200 engineers, including the foremost in each line. These papers were presented at technical sessions held in Fort Worth in October, 1927, and at the annual meeting in New York in February, 1928. We desire to express our thanks and appreciation to all those who have contributed to this volume. As in previous years, we have attempted to emphasize the value of both written and impromptu discussions. -We have made a practice of returning all impromptu discussions to the authors for correction and amplification, and because of this practice we feel that the discussions contained herein are in very presentable and readable form. It was decided by the nominat,ing committee when meeting for thc purpose of nominating officers for 1928 to eliminate the vice-chairrnanship for Transportation Engineering, as that branch of the industry seemed to come more naturally under the activities of the American Petroleum Institute. It was also decided by this committee to institute a new vice-chairmanship for Petroleum Engineering Research. Wc have had heretofore round table discussions on engineering research, but through the newly created vice-chairmanship, to which Mr. L. C. Uren was elected, we expect to have more comprehensive sessions on engineering research than heretofort.

Jan 1, 1928

Bill S.1431 for the creation of a Department of Natural Resources has received a propitious hearing before the Senate Committee on Government Operations. Interior Secretary Rogers C. B. Morton was one of the prominent witnesses who testified in favor. The department had been proposed, Morton said, with "the conviction that the development of all natural resources would be harmonized with the most practicable possible means to protect and preserve the environment, consistent with the social and economic needs of the Nation." Another opinion on the pro side came from Atomic Energy Commissioner Clarence E. Larson, who said that a "total picture" had become essential to the establishment of a policy for developing energy resources in the best public interest. Commissioner James T. Ramey, on the other hand, was one of the AEC dissenters. Ramey said he believed the reorganization of resource responsibilities would hinder efforts to deal with energy-environmental problems and prevent the use of AEC "expertise and facilities" to the greatest advantage. As Arnold Weber, associated director of the Office of Management and Budget, pointed out, however, retiring AEC Chairman Glenn T. Seaborg is in favor of the new department. Another supporter, and one who can cast a vote on the bill, is Sen. Frank E. Moss. Final Standards for emissions from new stationary sources will be published by the Environmental Protection Agency on October 27. The initial proposals, appearing in the Federal Register on August 17, called for limiting emissions per million Btu of heat input (maximum 2-hr average) to 0.2 lb of particulate matter, and, where solid fuel is burned, to 1.2 lb of sulfur dioxide and 0.7 lb of nitrogen dioxide. While the new rules are mainly for new plants, the EPA is also proposing them for "existing plants which are modified in such a way as to increase or alter. . . their emissions."

Jan 1, 1971

By Clarence Hicks

THE labor policy, of the Standard Oil Co. (New Jersey) is founded. first of all on paying at least the prevailing scale of wages in the community; on, the eight-hour day, with time and one-half for overtime; one day's rest in seven; sanitary and up-to-date working conditions; just treatment assured each employee; payment of accident benefits beyond the amount prescribed by the State compensation law; health supervision by a competent medical staff; payment of sickness benefits after one year's service; cooperation with employee in promoting thrift and better social and housing conditions; and assurance for a generous annuity at the age of 65, guaranteed for life after 20 years of service. Most of these features have been a part of the company's policy for many years, but it is only during the past two years that the cooperation of employees in determining these matters has been definitely assured through industrial representation. Industrial representation, in the Standard Oil Co., is a principle rather than a procedure. It is built upon the belief that personal association of those interested in any problem leads to a mutual understanding and a fair decision as to what is right. Fully believing in this, principle, representatives of employees and representatives of management evolved a simple plan, the basis of which is that it gives every individual employee representation at joint conferences on problems and fundamental principles affecting all those interested in the industry. It is based on cooperation, not antagonism; its operation makes perfectly clear both to management and to employees that their interests are identical, that mutual understanding and cooperation insure progress and success for all. Furthermore, experience has definitely shown that representatives of the employees are not only alert for the employees' interests but are as keen as the representatives of the management in determining and insisting upon fairness to the employer.

Jan 3, 1920

By F. R. Wadleigh

It is generally realized and very often admitted by both producers and consumers of coal that there is great need for a revision of existing commercial classifications, and this will involve, of course, determination of a standard classification and a constant revision of marketing practices as they are affected by coal classification. I recently sent out some 200 letters to producers and consumers with a request for their views on the subject of commercial classification. Nearly all of the replies from both sides were that there was needed some change in the present method. There were three or four dissenting voices but the great majority of opinion was in favor of the formulation of some standard commercial classification. The classifications in commercial use today can best be described as a hodgepodge. They are made upon different bases, have different names and have different ways. There are, for instance, about 11 single bases of classifications as used commercially and some 17 or 18 combination bases. Then there were the Tidewater Pool Exchanges. The classification which they put in force is still used in the tidewater markets and has several different bases of its own. It will be considerable of an undertaking to bring about a change in marketing methods as affected by coal classification but it is well worth doing and I think the committee which has been appointed under the auspices of the American Society for Testing Materials realizes the importance of the subject and is on the way to at least bring about some provision for adjusting matters. By way of starting, each member of the Committee on Commercial Classification has been assigned to a general market district and each member is now engaged in collecting the commercial market practice data for submission at the next meeting of the Committee. About a year ago I made up a list of the commercial classifications in the different markets and the total was 171. The 11 single bases I found used in commercial practice were:

Jan 1, 1930

By D. N. Witman

One of the special uses to which the electric furnace has been put recently is the melting of an alloy of nickel and cast iron for the production of electrical-resistance grids. The metal sections of these grids, Fig. 1, are quite uniform for each pattern, but there is, among the various patterns, a variety of thicknesses. The cross-sections vary from 1/2 by 3/16 in. to as small as 1/8 by 1/8 in. The electrical resistance of a perfect casting lies within 10 per cent. above or below the fixed listed resistance for each pattern. Good molding is essential to success in the making of these grids, for with absolutely correct metal, a variation of 0.01 in. in width and thickness of section on some of the patterns may mean as much as 12 or 14 per cent. variation in resistance. The service for which these castings are intended demands that the metal, even in the smallest castings, be very soft, showing an open, gray, highly graphitic structure, in order that they may be resistant to shock, and stand up well under rough usage. The metal used for this purpose is a gray iron alloyed with 4 to 5 per cent. of nickel, which element, when the composition of the alloy is correct, imparts toughness and pliability to the metal and helps to overcome the tendency of metal to run white and become brittle because of the rapid cooling action of the sand mold. When cold, these castings can be twisted into various shapes, taking a permanent set without breaking. The alloy has approximately double the e1etrical resistance of ordinary cast iron. The metal specification is as follows: Per Cent. Silicon............................................. 2.40 to 2.60 Sulfur............................................. Under 0.05 Phosphorus......................................... Under 0.08 Manganese......................................... Under 0.40 Total carbon....................................... 3.60 to 4.00 Nickel............................................. 4.00 to 5.00 Copper............................................ 0.50 to 0.70

Jan 1, 1922

By D. N. Witman

ONE of the special uses to which the electric furnace has been put recently is the melting of an alloy of nickel and cast iron for the production of electrical-resistance grids. The metal sections of these grids, Fig. 1, are quite uniform for each pattern, but there is, among the various patterns, a variety of thicknesses. The cross sections vary from 1/2 by 3/16 in. to as small as 1/8 by 1/8 in. The electrical resistance f a perfect casting lies within 10 per cent. above or below the fixed listed resistance for each pattern. Good molding is essential to success in the making of these grids, for with absolutely correct metal, a variation of 0.01 in. in width and thickness of section on some of the patterns may mean as much as 12 or 14 per cent. variation in resistance. The service for which these castings are intended demands that the metal, even in the smallest castings, be very soft, showing an open, gray, highly graphitic structure in order that they may be resistant to shock, and stand up well under rough usage. The metal used for this purpose is a gray iron alloyed with 4 to 5 per cent. of nickel, which element, when the composition of the alloy is correct, imparts toughness and pliability to the metal and helps to overcome the tendency of metal to run white and become brittle because of the rapid cooling action of the sand mold. When cold, these castings can be twisted into various shapes, taking a permanent set without breaking. The alloy has approximately double the electrical resistance of ordinary cast iron. The metal specification is as follows: PER CENT. Silicon 2.40 to 2.60 Sulfur Under 0.05 Phosphorus Under 0.08 Manganese Under 0.40 Total carbon 3.60 to 4.00 Nickel 4.00 to 5.00 Copper 0.50 to 0.70

Jan 8, 1921

By D. N. Witman

One of the special uses to which the electric furnace has been put recently is the melting of an alloy of nickel and cast iron for the production of electrical-resistance grids. The metal sections of these grids, Fig. 1, are quite uniform for each pattern, but there is, among the various patterns, a variety of thicknesses. The cross-sections vary from 1/2 by 3/16 in. to as small as 1/8 by 1/8 in. The electrical resistance of a perfect casting lies within 10 per cent. above or below the fixed listed resistance for each pattern. Good molding is essential to success in the making of these grids, for with absolutely correct metal, a variation of 0.01 in. in width and thickness of section on some of the patterns may mean as much as 12 or 14 per cent. variation in resistance. The service for which these castings are intended demands that the metal, even in the smallest castings, be very soft, showing an open, gray, highly graphitic structure, in order that they may be resistant to shock, and stand up well under rough usage. The metal used for this purpose is a gray iron alloyed with 4 to 5 per cent. of nickel, which element, when the composition of the alloy is correct, imparts toughness and pliability to the metal and helps to overcome the tendency of metal to run white and become brittle because of the rapid cooling action of the sand mold. When cold, these castings can be twisted into various shapes, taking a permanent set without breaking. The alloy has approximately double the e1etrical resistance of ordinary cast iron. The metal specification is as follows: Per Cent. Silicon............................................. 2.40 to 2.60 Sulfur............................................. Under 0.05 Phosphorus......................................... Under 0.08 Manganese......................................... Under 0.40 Total carbon....................................... 3.60 to 4.00 Nickel............................................. 4.00 to 5.00 Copper............................................ 0.50 to 0.70

Jan 1, 1922

By D. I. Cameron

A graphical method has been developed and tested for separating the effects of grain boundary and lattice diffusion in polycrystalline materials. The method is based on the assumptions that for unidirectional diffusion from a plane source of radioactive material, the penetration of activity far into the specimen from the source is due solely to grain-boundary effects, and 2) pure grain-boundary penetration is described by a linear plot of log activity vs the perpendicular distance x from the source. The former is based on the fact that at any temperature the grain-boundary diffusion coefficient is always very large relative to the lattice diffusion coefficient; and the latter is based on the derivation of Fisher.1 Using these criteria along with appropriate penetration data (in this case, data for the diffusion of Cb95 in pressed and sintered UO2) one first plots the data as log activity vs x2 and as log activity vs x, as shown by curves 1 and 2, respectively, in Fig. 1. A tangent line to curve 2 for large x (curve 3) is then transferred to the x2 plot as curve 4. The subtraction of curve 4 from curve 1 yields curve 5 which represents only lattice diffusion and may therefore be related to the diffusion coefficient by using the appropriate solution to Fick's second law. It should be noted that the method has inherent inaccuracies for small and large values of x2 and only the subtraction at intermediate values can be used. For the illustrated specimen the calculated diffusion coefficient is 3.4 X 10-11 sq cm per sec at 1445°C while data using a single crystal of UO2 at the same temperature yielded a value of 2.9 x 10-11 sq cm per sec.2 The same method of subtracting grain-boundary diffusion effects to obtain lattice diffusion coefficients has been successfully used to determine self-diffusion coefficients of Th230 in polycrystal- line thoria.

Jan 1, 1962

By Herbert Wilson

THIS topic was discussed at the meeting in St. Louis in September, 1917, and at the meeting in New York in February last, but in the interval the war has accentuated in measurable degree the necessity for considering human relationship, not only as between nations, or in the treatment of our returning soldiers, but with respect to the relations between labor and capital in industry. It is my firm conviction that no other subject will have so large a place in industrial and political life during the next decade as this. Heretofore, the employer has been so engrossed with the financial, mechanical, and technical aspects of his business that he, has been willing to muddle through 'his relations with labor as best lie might and, on the other hand, the laborer has been so engrossed in his endeavors to secure a livelihood under whatever living and working conditions might be offered him that he has given little thought to his relations to his employer, until some misunderstanding has ended in disagreement and strike. No thinking man doubts that were the machinery available for friendly, personal, face-to-face consideration of the problems confronting employer and employee, there would he fewer disagreements, fewer strikes, and a better and more settled industrial situation. The necessity for some such medium for exchange of views has resulted in the organization of labor and, in some measure, of capital. Each party, engrossed only in defending its own viewpoint, has generally tried to gain its point by might rather than by right. Gradually, however, the representatives of both elements are beginning to appreciate that when the machinery for bringing them together in friendly communion is available their differences frequently settle themselves. There remain yet vast numbers of employers and of employees who are not organized and to whom the opportunity of friendly discussion of differences is not available; for these the machinery should he provided.

Jan 1, 1919

By Jacob T. Wainwright

This stove has been designed to meet the requirements of a fur nave that must be operated with either a reducing or a neutral flame ; and more particularly to make feasible the operating of re duction-furnaces with the cheaper grades of gas-fuel, which has heretofore been impracticable. In general, cheap gas-fuels result from incomplete combustion, and, being suited for further combustion, answer very well for heat ing purposes; and high temperatures may be attained with them, when they are used in conjunction with regenerative stoves. But, in operating a reduction-furnace, a high temperature is not the only requirement. It is also necessary that the fuel shall not be cansumed beyond a certain degree, in order to insure a re ducing flame for the reduction-process ; consequently, it becomes necessary to dispense with combustion as much as possible previous to the use of the fuel-gases in the reduction-furnace. Moreover, these gases must be preheated to a high degree, in order that a sufficient temperature may be maintained in the furnace; and, since this preheating cannot be accomplished by a previous, partial combustion of the gases themselves, it follows that the stoves for pre heating these gases should be heated to as high degree as it is pos sible to attain with an inferior fuel. This result can best be accom plished by complete combustion of the heating gases, and is further facilitated by preheating all of the air and gas used for this com plete combustion. It is more particularly desirable to preheat the air, since the combustible gases used may generally be obtained directly from the furnace, or gas-producer. The reducing gases, escaping from a gas-fuel reduction-furnace, are capable of considerable further dilution with air to secure com plete combustion, and consequently may be utilized for heating the stove to a high temperature, provided the air be sufficiently preheated.

Jan 1, 1889

By J. G. Montgomery

An increased drilling activity was apparent in the shallow sand fields of northwestern Pennsylvania during the year. This drilling, however, was confined to previously outlined productive areas and as new shallow sand pools of interest were discovered. Drilling for Oriskany gas proceeded at about the same rate as in previous years. One new area in Kinzua township, Warren County, was opened up during the year by a producing well, but later this well developed salt water and the productive capacities of the area are very indefinite at the present time. Production from the shallow sand areas remained approximately the same as in 1935. Production from the Oriskany or deep sand areas increased approximately 20 per cent. Two new markets were made available for the Oriskany gas during the closing months of the year by the completion of the Peoples Natural Gas Co. line from the Hebron field to Clarion County, Pa. and Penn York Gas Co. line from the Harrison field to points in northwestern New York State. With the exception of the Kinzua well, the few deep wildcat wells drilled during the year failed to discover new fields in the deep sands. Bradford Oil Field The accompanying data on the Bradford oil field include only the production obtained from the portion of that field that is in the State of Pennsylvania, for it appears probable that Cattaraugus County production, which consists mainly of the New York State portion of the Bradford field, will be included in annual oil production figures for New York State. The Bradford field production for 1936 totaled 14,533,000 bbl., and as it is necessary to estimate New York State production for the Bradford field, the accompanying data includes the production from the Pennsylvania end of the Bradford field of 13,208,000 bbl., which is an increase of approximately 8 per cent over 1935 production.

Jan 1, 1937

Prof. HEnRy Louis, Newcastle-upon-Tyne, Eng. (communication to the Secretary*):—I welcome Mr. Hammond's paper as an attempt to give definiteness to the best modern professional practice. Such a codification of our professiollal ethics is urgently needed, seeing how widely the views of nlining engineers direr on some of the points raised; for example, I have no hesitation in performing a class of work, as to which Mr. Hammond seems to entertain some doubts, and, on the other hand, I strongly condemn a practice which he appears to recommend. I have not the least hesitation in making reports for vendors of mining-properties, and am constantly doing so; the best justification for this practice may be found in the fact that such reports have been repeatedly accepted by buyers as giving a correct representation of the facts of the case, which is all that should be demanded from any report. On the other hand, Mr. Hammond advocates that mining engineers should take payment for their reports in shares of a company to be floated upon the basis of such reports. I hold that this is ethically wrong, as even themost honest of men is liable to be unconsciously biased under these conditions. Indeed, I go much further, and maintain that a mining engineer who reports or advises upon mining-properties should never hold any mining-shares at all, or be himself interested in any mine, and this has been my consistent practice for many years. A man who hold shares in a mine, and is called upon to report upon a neighboring property or a similar mine, can never be wholly unbiased; and even if he could be, he would always lay himself open to the suspicion that he was giving a favorable report 80 as to enhance the value of the property in which he himself is interested, or an unfavorable report so as to stifle competition. It is quite as bad for the manager of a mine or the consulting manager to be interested, because he will have access

Jan 1, 1910