Search Documents

By K. G. Davis, P. Fryzuk

The diffusivity of silver in liquid tin has been determined, using the capillavy-reservoir technique, over the temperature range 250° to 500°C. The new value, D = 2.5 x 10'* exp(-2480/ RT) sq cm per sec, differs from that obtained by other workers in an earlier investigation. The analysis of data from the capillary-reservoir technique is discussed. In a recent investigation of the solidification of dilute alloys, values for the diffusion constant of silver in liquid tin were required in the analysis of the formation of impurity substructures. AS a result, measurements were made of the diffusion constants in the temperature range 250° to 500°C (melting point of tin 232°C), for the alloy concentrations used in the solidification experiments and at higher concentrations, to verify previous determinations.I)2 The capillary-reservoir method was adopted, using experimental procedures similar to those followed by Ma and Swalin,1 with the main exception that radioactive silver was used in the present investigation to facilitate solute-concentration measurements. EXPERIMENTAL PROCEDURE a) 100 ppm Samples. Glass capillary tubes of 2 mm inside diameter and approximately 5 cm- long were sealed at one end, evacuated, and filled with tin of 99.999 pct purity. The region of shrinkage near the mouth was cut off, and the tubes were then placed in a graphite holder and immersed, with the open end up, in an unstirred bath of alloy containing 100 ppm Ag 110, where they remained for periods of up to 30 hr. On removal from the bath they were cooled by an air blower. The bath was kept under a small positive pressure of argon, and the temperature controlled to within +1°C. A 10-hr diffusion period was used in the majority of the tests, scatter on runs of less than 5 hr being rather large. The procedure outlined above was chosen in preference to putting alloy in the capillary and pure tin in the bath, in order to avoid segregation when the tubes filled with alloy were first solidified. To minimize segregation when the diffusion period was complete and the capillaries again solidified, the earlier samples were held in thin-walled silica tubes which could be cooled very rapidly. Later tests were made in precision-bore Pyrex tubes, to eliminate effects caused by variations in the capillary diameter. No consistent differences in diffusivity as measured in the two types of tube were detected. After removal from the glass tubing, the samples were sectioned into 2.5 mm lengths and counted for y activity, using a scintillation counter with fixed geometry. Samples were also drawn directly from the bath and counted, so that values for C/C,, the ratio of the weight of Ag 110 in the sample to that in the bath, could be obtained. b) 5000 ppm Alloy. To check for possible effects of concentration, the silver content of the bath was increased to 5000 ppm. Complete mixing was found to have taken place in the capillary after a 10-hr period at 300°C. It appears that the greater density of the alloy was sufficient for buoyancy forces to cause instability in the alloy-tin interface, leading to rapid convective mixing. For the 5000 ppm alloy, therefore, the bath was of pure tin and the capillary tube was filled with alloy. With this arrangement, values of D consistent with those for the 100 ppm alloy were obtained, Fig. 1. CALCULATIONS OF DIFFUSIVITY The terminology used applies to a capillary of pure tin immersed in a bath of alloy. 1) Error-Function Method. under the present experimental conditions, the rod of liquid tin into which silver is penetrating may be considered semi-infinite. Assuming the concentration at the mouth of the tube to remain constant at Co, the concentration C at distance x from the mouth of the tube at time / is given by3 Plots of the inverse error function of (1 -C/Co) vs .v gave straight lines passing through the origin with slope 1/2-, x being corrected for shrinkage both on solidification and while cooling to the melting point (total correction about 6 pct at 500°C). Values for log D obtained in this manner are shown in Fig. 1. A least-squares fit to the relation D = Do exp(-Q/RT)

Jan 1, 1965

By E. J. Fasiska, H. Wagenblast

The dilalion of a ivon by interslilial carbon was measured by two independent techniques —dilatometric mesurements at 719 c and X-ray measurments of the urlil cell parameters a1 room temperature after quenching. The relative expansion per increase in cavbon content by both methods is (2.9 + 0.3) x 10-3 pev at. pcl C nrzd is temperature- independent within experimental error. This corresponds to (6.3 5 0.6) cu cm per g-atom for the partial gram-atomic volume of carbon in a iron-only slightly smaller than the atomic volume for iron in the same temperature vange. THE only previous quantitative study of the dilational effect of carbon dissolved in a iron was performed in 1934 by Burns1 which, at the time, generated some discussion of possible sources of experimental error.2 For a system of such widespread importance, we felt that a new investigation was merited. Both X-ray diffraction and dilation measurements were used to determine the expansion of the a iron lattice by dissolved carbon, avoiding as much as possible any previous experimental problems and deficiencies. The dilation method at solution temperature offers not only measurements which are free of residual strain but also, in conjunction with the room-temperature X-ray measurements, a method to detect any large temperature dependence of the partial gram-atomic volume of carbon. To insure that quenching strains did not affect the room-temperature X-ray measurements, wire specimens of constant carbon content but different diameter were examined for such an effect. SPECIMEN PREPARATION The material used for both experimental techniques was "Ferrovac E" iron received in the form of 19-mm-diam rod and stated as having the following impurity contents: C, Cr, Cu, Mn, P, and V, each in the range of 10 to 50 ppm; Co, O, Mo, S, and Si, 60 to 100 ppm; W, 200 ppm; Ni, 230 ppm; N, 4 ppm. The stock material was cold-swaged to 0.71 mm diam for the Debye-Scherrer X-ray camera specimens and portions were cold-rolled from 6.3 mm diam to 0.79- and 0.25-mm sheet for X-ray diffractometer and dilation measurements. The wires were annealed in wet hydrogen for 6 hr at 840°C and 15 hr at 720°C, and then quenched into 0°C water. A chemical analysis for carbon after this treatment gave 0.0046 + 0.0014 at. pct C. Three portions of these wires were subsequently held at 719°C in three different hydrogen + methane mixtures and then quenched, resulting in carbon concentrations of 0.0283, 0.0598, and 0.1067 at. pct C by chemical analysis. After carburizing, the wires were swaged to 0.48 mm and electroplated with silver to prevent carbon loss during subsequent heat treatment. The final heat treatment consisted of holding the wires at 72 1°C for 5 min in a He-2 pct H mixture followed by quenching into 0°C brine. The wires were held at room temperature for a few minutes to remove the silver plating using a phosphoric acid-hydrogen peroxide solution, and then stored in liquid nitrogen until the measurements were made. EXPERIMENTAL TECHNIQUE A) Dilation Measurement. The dilatometer consisted of a gas-atmosphere vertical tube furnace modified so that length changes of a ribbon-shaped specimen could be measured externally. This was done by installing a gas-tight mercury seal at the top of the furnace as shown schematically in Fig. 1. The specimen (21.0 cm long, 1.27 cm wide, and 0.25 mm thick) was suspended in the center of the furnace by 3-mm-diam quartz rods with the upper one passing through the cap of the mercury seal. Above the cap, the upper quartz rod was coupled to a lever exerting a load of about 25 g (-12 lb per sq in.) on the specimen and having a 10 times mechanical magnification. The vertical position of a marker at the other end of the beam was read with a traveling microscope with a precision of 0.01 mm. The temperature gradient of the furnace was meas-

Jan 1, 1968

By Merlon C. Flemings, Theodoulos Z. Kattamis

Examination was made of the distribution of tnanganese and nickel in colutrrnar dendrites of a cast low-alloy steel; more limited work was corzducted on chromium. Corresponding "segregrction ratios" were calculnted and shown to be relntivelv insensitive to cooling rate (''segregation ratio" is defined (Is the ratio of maximum to minimum concentrations within a volume whose dimensions are the order of the dendrite-arm spacing). Isoconcentratiorl curves were determined by the electron micropvobe and by rt7etallografihic studies on specimens subjected to isothermal-transformation treatments. From construction of isoconcentration curves, morphology of columnar dendrites is descvibed as intermediate between Perfect rodlike and sheetlike morphologies. The study is extended to equiaxed dendrites and it is shown that the strcture of these dendrites is sittlilar in many respects to that of columnar dendrites. On the basis of tlze sheetlike morphology of dendrites, a simple model is pvoposed for calculation of honzogenization kinetics. Results of trzatllevlatical analysis brcsed on this utzodel are given. This analysis relates residual segregation to time at homogenization temperature; it is in agreement with experiment. Calculations are given which show that even for relatively rapidly cooled material (of 1-ine dendrite-artn spacing) treatmets at 1200°C or above are necessary to achieve slgxificant Izomogenization of elenlents other than carbon itz reasonable time (e.g., rnangclnese, nickel). Conlplete homogenization of carbon is obtnined at much lowev tenlperatures (below 870°C). IN dendritic solidification of castings and ingots, solute redistribution during freezing results in mi-crosegregation of most alloy elements. The micro-segregation is such that minimum solute concentrations occur at the center of dendrite arms and maximum concentrations occur between dendrite arms. Residual segregation after subsequent therma1 processing (homogenization) depends on maximum and minimum initial concentration, on the detailed geometry of the isoconcentration surfaces within interdendritic regions, on the diffusion coefficient of the solute, and on time of thermal processing. The objective of this work was to determine, for a low-alloy steel, maximum and minimum concentrations, and the geometry of isoconcentration surfaces, primarily in order to permit calculation of homogenization kinetics. Most of the work reported was conducted on Samples from a unidirectionally solidified, fully columnar ingot. This type of ingot is made by extracting heat during solidification from one face; techniques for accomplishing this have been discussed.' Samples were taken at several locations, up to 5.75 in. from the mold chill face; the bulk of the work was performed on samples at 5.75 in. Alloy cast was, nominally, 0.4 pct C, 1.8 pct Ni, 0.8 pct Cr, 0.7 pct Mn, 0.25 pct Mo, 0.3 pct Si, and the balance iron. Brief study was also made on samples from an ingot which solidified with equiaxed grain structure. SAMPLE PREPARATION AND ANALYSIS Samples for electron-microprobe analysis were incorporated in mounts that included pieces of electrolytic nickel, chromium, and manganese, in order to normalize the intensities of these solutes in the specimens; also, a piece of electrolytic iron was included to measure the background. All specimens were polished in the usual metallographic manner. After the microprobe traces were made, the path was revealed by etching the specimens with picral. All microprobe analyses were made by point counting, integrating for 30 sec. The distance between points was fixed from 2 to 10 p, according to the precision desired in each case, the fineness of the structure, and the concentration gradient existing in a given area. (The distance was chosen 2 to 5 p near the maximum-concentration regions and 5 to 10 p near the minimum concentration.) The "take-off" angle for the A.R.L.-Model No. 21000 microprobe employed was 52.5 deg. Samples for metallographic analysis of isoconcentration curves were prepared by austenitizing at 1540°F for 20 min, quenching to the nose of the TTT curves (1200°F), heat treating isothermally at this temperature for a given time 0, and then quenching to room temperature. Due to concentration gradients existing in a dendritic structure, no transformation will take place for a given time 0 of isothermal heat treatment in the regions where the a.lloy concentration is higher than a given limit. Thus, the dendrite appears limited by an isoconcentration curve and can be made to appear to grow by varying the time of isothermal heat treatment.

Jan 1, 1965

By O. D. Sherby, J. E. Dorn

For elevated temperature-constant load creep tests of a solid solution alloys, the creep strain is a function of a temperature-compensated time parameter 0 = je H/RT dt. The activation energy H is equal to o constant of about 36,000 cal per mol. The substructures resulting from a given creep stress condition are functions of the creep strain independent of temperature. Each new creep stress gives a new unique set of grain substructures; this is one of the factors responsible for the failure of the mechanical equation of state for creep. IN this report an attempt is made to correlate the creep properties of dilute a: solid solutions in aluminum with the subgrain structures that are developed during creep. The possibilities of such correlations have already been suggested by Wood et al. and others1-" who demonstrated that the subgrain structures are functions of the creep stress, creep strain, rate of creep, and temperature. Investigations by Sherby and Dorn' have shown that the creep strain, E, at constant load for dilute a solid solutions of aluminum is given by the functional relationship: e = f(8,u,) [1] where: 0 equals te-AH/RT = temperature-compensated time; t, time; AH, activation energy, - 35,800 cal per mol; R, gas constant; T, absolute temperature, above 400°K; and u,, initial creep stress. Consequently, it was anticipated that the subgrain structure that develops during a constant load creep test should also correlate with any two of the three significant variables C, 8, and Another possible correlation between the subgrain structure and the creep variables is obtained by differentiating Eq. 1 with respect to time, whence the creep rate, 2, becomes: = (2L) (2) =f (, u,) e-AHRT [2] or: e = F (c e H/RT, 0) [3] For the minimum creep rate, ;,, 8 is solely a function of U, as revealed by Eq. 1. Consequently, at the minimum creep rate Eq. 3 reduces to: = F (eAH/RT) [41 Correlations between U, and i, eAH/RT were found valid for solid solution alloys of aluminum where AH was a constant of about 35,800 cal per mol. The parameter ;, eH/RT is identical to the Zener-Hollo-mon parameter8," used by them in evaluating the tensile properties of copper and other metals. Eq. 4 suggests that the subgrain structure developed during secondary creep might be correlatable with either of the two variables 2, e H/RT or u,. Some of the solid solution aluminum alloys which were discussed in an earlier report' were also used in the present investigation. Sheets of these alloys were homogenized, cold rolled from 0.100 to 0.070 in. in thickness and then recrystallized to about the same grain size. Their chemical composition and grain size are recorded in Table I. Creep specimens were selected with their tensile axes in the rolling direction. The details for creep testing have been described10 and will not be repeated here. All creep tests were performed under constant load conditions. Experimental Results and Discussion Metallographic Structure of Creep Specimens: In order to obtain a preliminary concept of creep on the metallographic structure of high purity aluminum, the various ruptured specimens previously used to obtain the creep data for pure aluminum were polished and etched electrolytically in a dilute solution of fluoroboric acid. Oblique illumination was used to reveal the substructures which, for convenience, are shown in correlation with the vs. ;, eH/RT curve in Fig. 1. It is necessary to emphasize that the data for the curve refer to the various secondary stages of creep whereas the micrographs refer to the fractured creep specimens. Nevertheless a regular and systematic correlation is observed between E, eAH/RT (or the creep stress) and the micro-structure at fracture. For In (e, eAH/RT) = 42.3, which refers to creep at a high creep rate and a low creep temperature, the fractured aluminum specimen, as shown by the micrograph in the upper right-hand corner of Fig. 1, exhibited extensive deforma-

Jan 1, 1954

By Joseph L. Gillson

IT is a somewhat curious circumstance that the newest of the Institute's several awards should be conferred in the oldest of our several professional fields—for there is little question that geology and mining have antedated metallurgy and petroleum. Perhaps so did geophysics. After all, one geophysical instrument, the magnetic compass, has been successfully employed for many centuries. Young in years the Jackling Award may be, but in distinction—whether in terms of the title it bears or in terms of the first three medalists (Reno Sales, E. D. Gardner, and the late Father MaceIwane)—the Jackling Award is already one of the ranking awards of the Institute. The name of the 1957 medalist will bring added luster to an already illustrious roll. J. L. Gillson was born and brought up in Evan-ston, Ill., in an area characterized by singularly flat and uninspiring topography, and devoid of ore deposits and even of bedrock—a most unlikely environment from which to expect a future Jackling medalist to emerge! On graduating from high school he enrolled as a chemistry major at Northwestern University. At the end of his frkshman year his scholastic prowess had won him a prize of two chemistry books. But these went unread, for about this time he came under the spell of U. S. Grant, that distinguished and enthusiastic geologist who for many years was head of Northwestern's geology department. From thence forward Joe was a dedicated geologist. After a Navy interlude in World War I, he went to MIT for graduate work, substituted for the late Professor Palache for one year at Harvard in mineralogy, received his doctorate at MIT and stayed on as a meniber of the MIT faculty, where the geology department was headed by that great dean of all economic geologists, Waldemar Lindgren. In 1926 Joe spent a summer looking into barite deposits for the du Pont Co., and since 1928 he has been du Pont's chief geologist. Do men who lead such active lives in our exploration organizations generally have permission to publish their observations? Do they generally find time to publish, even if they have permission? Alas, no. But in Joe Gillson's case, yes. His bibliography runs to well over two score papers, including one of the very first papers in this country on the applications of petrography to problems of Portland cement. He has written on such topics as the origin of talc and the genesis of ilmenite, fluorspar, and alkaline rocks. Each year for a number of years his annual reviews of industrial minerals in the Mining Congress Journal have been eagerly awaited. - Do men who do so much to advance their science have anything left to give to the advancement of their profession? In Joe Gillson's case, yes. He has been a vice president of the Mineralogical Society of America and has been active in the councils of the Society of Economic Geology, particularly in their research programs. This year he is president of the American Geological Institute, currently perhaps the most challenging post to which a geologist may be elected. His contributions to AIME scarcely need documentation, so I shall mention only three—his chairmanship of the Committee on Democratization of the Institute, a committee whose work and recommendations brought a new and hopeful leaven to AIME at a time when this was sorely needed; his chairmanship, a few years ago, of the Industrial Minerals Division; and his current place on the Board of Directors as Vice President of the Institute. Such' a catalogue of contributions and achievement, even as condensed as I have had to make it, certainly merits the Jackling Award. Yet, implicit although not often expressed in the conferring of most awards is the hope that besides recognizing a distinguished career, it will provide stimulus for further effort. In the present instance, such an expectation is already well on the way to fulfillment. Only recently Joe Gillson has undertaken the editorship of a new and greatly revised edition of the Institute's Seeley Mudd volume, Industrial Minerals and Rocks. And so, Mr. Chairman, it is with pleasure and enthusiasm that I present Dr. J. L. Gillson for the 1957 Jackling Award.

Jan 1, 1958

By W. M. Robertson

The kinetics of grain boundary groove formation on copper surfaces immersed in liquid lead have been studied over the temperature range of 400° to 900°C. The groove widths were Proportional to the cube root of the annealing time, indicating that the diffusion of copper through the saturated liquid-lead solution is the mechanism by which grooves form. The rate constant for the process can be calculated by a theory due to Mullins. Using published data for the solubility of copper in liquid lead, for the interfacial energy of the solid copper-liquid lead interface, and for the diffusion coefficient of copper in liquid lead, the calculated rate constants almost exactly reproduce the measured values over the entire temperature range. The decay of scratches placed on copper surfaces has also been studied. The rate constant for scratch decay agrees with that for grain boundary groove growth, though scratch decay is sensitive to convection currents in the liquid. The interaction of solid and liquid metals has been studied extensively and has been found to be rather complex. Many of the studies have been complicated by a host of competing effects, including temperature gradients, concentration gradients, the formation of one or more intermetallic phases, natural or forced convection, and the presence in both the solid and liquid of considerable amounts of impurities and alloying elements. Recently theories have been developed of changes in surface profiles driven by capillary forces,' which allow the interaction of the solid and liquid to be analyzed quite directly. The present paper reports a study of the formation of grain boundary grooves on pure copper immersed in liquid lead, which allows the theory to be checked quantitatively. The Cu-Pb equilibrium diagram is quite simple: there are no intermetallic compounds, copper is just slightly soluble in liquid lead, and lead is almost completely insoluble in solid copper.2 The Cu-Pb system has been studied extensively,3-9 and all of the quantities—interfacial energy, diffusion coefficients, and equilibrium solubilities-necessary to calculate the rate of groove growth by a volume-diffusion mechanism are known. The kinetics of grain boundary grooving and scratch smoothing have been studied on the noble metals and the iron group metals in a reducing atmosphere or in vacuum.10 The main interest of these studies has been the determination of surface-diffusion coefficients at metal-gas interfaces using the theories developed by Mullins.1 The present paper uses similar methods for the study of diffusion processes at the interface between two condensed phases. There has been one previous study" of the kinetics of groove growth in a solid-liquid system, which, however, was troubled by the fact that neither interface energies nor diffusion coefficients were known in the Ni-S system studied. THEORY The theory of grain boundary groove growth has been developed by Mullins for the cases of volume diffusion," surface diffusion," and a combination of the two processes.14 He has also analyzed the kinetics of the flattening of a scratched surface by these processes.l5,l6 Several assumptions and approximations were used in the derivations of the surface profile shapes. The applicability of these assumptions and approximations to the present system will be considered in the discussion. At the intersection of a grain boundary with an initially flat interface the equilibrium between the interfacial energy and the grain boundary energy establishes an equilibrium groove angle. This induces curvatures in the interface. The chemical potential of material at a curved interface is higher than at a flat interface, so that material moves away from the region of the grain boundary. Mullins' calculations indicated that the groove profile would be similar to that shown schematically in Fig. 1. Small humps form above the level of the original flat surface. For a volume-diffusion mechanism the separation, w, of these humps at a time, t, is given by and where co is the equilibrium concentration of the solid in the liquid, y, the solid-liquid interfacial free energy, O the volume occupied by a solute atom in the liquid, D the diffusion coefficient of the solid in the liquid, and kT has its usual meaning. For a surface-diffusion mechanism the groove width is proportional to the fourth root of the time. For grooves forming by a combined surface and volume-diffusion mechanism the exponent of the

Jan 1, 1965

By Peter Soo

Pvestrained Ferrovac E iron has been neutron-irradiated at approximately 90°C to an integrated flux of 1020 nut (E > 0.82 mev]. The irradiation was found to produce an incveased temperature dependence of the flow stress in addition to a greatly increased athemal stress. Measurements of the flow stress and stress relaxation, from which the activation volume and activation energy for slip were deduced, show that neutron irradiation changes the rate -controlling slip process to one based on dislocation interactions with tetragonal distortions which are Produced around submicroscopic interstitial loops in the lattice. The study indicates that without prestraining prior to irradiation the chances of detecting a change in the rate -controlling slip process are greatly reduced because in the initial stages of slip a substantial fraction of the radiation defects are swept out of the slip plane by gliding dislocations. Thus, activation parameters which are subsequently measured are representative of a greatly reduced defect density and would not differ appreciably from those for unirradi-ated material. The large increase in the athermal component of the flow stress is probably connected with the presence of depleted zones in the lattice which are introduced by irradiation. ALTHOUGH fast neutron-irradiation has not been observed to markedly alter the activation parameters for slip in bcc metals,' small but significant changes do occur. Most experimenters agree that irradiation predominantly increases the athermal component of the yield stress.'-= In addition to this, Laidler and smidt7 have shown that in iron irradiated to 5 X 10" nvt and molybdenum irradiated to 10" nvt, changes occur in the activation volumes for slip. A similar conclusion has been reached by Milasin and Malkin8 for irradiated iron. Work by Ohr et a1.5 shows that for Ferrovac E iron, irradiated to 1.2 X 1016 nvt, small increases in the activation energy for slip also occur. So far these changes in the activation parameters have not been explained on a firm theoretical basis. One important factor which would minimize the chances of detecting a change in the slip mechanism upon irradiation is the presence of "channeling" which has been observed in molybdenum,9 niobium,10 and iron.11These channels are formed by gliding dislocations which sweep irradiation defects out of the active slip planes and thereby create zones in which continued dislocation motion is encouraged. The activation parameters for the dislocations gliding in the defect-free channels would, therefore, be similar to those for unirradiated iron and a change in the rate-controlling slip process would be difficult to detect. In the present work, an attempt has been made to reduce the effect of uneven deformation on the measured activation parameters for slip in neutron-irradiated Ferrovac E iron polycrystals, so that a more realistic assessment of the effects of neutron-irradiation could be made. Primarily, the experiments involve the irradiation of specimens which had been prestrained to 9 pct elongation at room temperature prior to insertion into the reactor. It was hoped that the introduction of a large number of evenly distributed dislocations would substantially decrease any channeling effect which might otherwise occur. MATERIAL AND EXPERIMENTAL PROCEDURE The starting material was vacuum-melted Ferrovac E iron, an analysis of which is given in Table I. The standard tensile specimen had a gage length of 1.125 in., a cross-sectional diameter of 0.120 in., and a re-crystallized grain size of 1.2 x 10-3 in. All tensile tests were conducted on a floor model "Instron" tensile machine at a strain rate of 3 x 10-4 per sec. The irradiation of the prestrained specimens was performed in the Brookhaven High Flux Beam Reactor to an integrated flux of 1020 nvt (E > 0.82 mev) at a temperature of about 90°C. All specimens were excap-sulated in high-purity aluminum sheaths which were lightly swaged around the samples to ensure good thermal contact. Subsequent measurements on the irradiated specimens showed that within experimental accuracy the swaging had not deformed them. EXPERIMENTAL RESULTS Fig. 1 shows the flow stresses for a series of unirradiated control samples. In order to produce a comparable dislocation substructure throughout the test sm range, all specimens were prestrained

Jan 1, 1970

By S. R. Balajee, I. Iwasaki

The interaction between British gum 9084 and dode-cylammonium chloride (DAC) at quartz and hematite surfaces was established from coadsorption studies and streaming potential measurements. The cationic DAC interacts with the somewhat anionic British gum 9084, leading to the formation and adsorption of a binary complex of DAC-British Gum 9084 at the interface. The parallel ability to depress quartz along with hematite as a result of the interaction between DAC and British gum appears to be the main reason for the ineffective depressant action of starches and starch derivatives in the cationic flotation of iron ores. Amines are not particularly selective collectors for the flotation' of siliceous gangue from iron ores and, therefore, a suitable iron oxide depressant is needed for a satisfactory separation. Various starches and their derivatives have been extensively tested with oxidized iron ores,'-3 and it has been empirically established that British gums and dextrins are preferable. However, for the flotation upgrading of magnetite-taconite concentrates from 8 or 8.5% Si O2 to about 5% Si 02, British gums, which have been used so successfully on oxidized iron ores, have been found to have no effect and oftentimes are actually deleterious.4 In previous articles,5-7, starches were shown by adsorption measurements, flotation tests, and floccula-tion tests to interact with calcium ions in solution, and it was thought that a study on the interaction between starches and dodecylammonium ions would be able to shed some light on the anomalous flotation behavior described above. In fact, starches are known to interact markedly with paraffin-chain-type surface active agents and, thereby, to precipitate the starch or inhibit the iodine-starch reaction.8 From X-ray diffraction studies and viscosity measurements, the formation of a helical complex between mylose and a surface active agent has been postulated.9 The interaction with other types of hydrophilic colloids, such as synthetic polymers and proteins, has also been investigated and is usually explained in terms of van der Waals' force interaction and/or ion-ion interaction. In the present investigation, the interaction of British gum and dode cylammonium chloride on quartz and hematite was studied by adsorption and streaming potential measurements in an attempt to establish the mutual adsorption behavior of British gum and dode-cylammonium chloride on mineral surfaces and to clarify the anomalous depressant activity of British gum in the cationic flotation of iron ores. All the measurements were carried out at a natural pH of near 7 because dodecylammonium chloride gives maximum selectivity of flotation separation at this pH2 and to avoid any third parameter in the system. EXPERIMENTAL MATERIALS AND METHODS Minerals: The quartz and hematite samples used for the adsorption tests were prepared as described in a previous paper,"J except that the specific surfaces of the samples were increased to 5,860 and 16,000 Sq cm per gm, respectively. For the streaming potential measurements, the 48165-mesh fractions screened out of the original samples were etched with hydrochloric acid, washed repeatedly with water, and stored under water in Pyrex bottles. Reagents:DodecyIammonium chloride (DAC) was prepared1 1 by bubbling dry hydrogen chloride gas through a benzene solution of high-purity dodecylamine supplied by Armour and Co. British gum 9084, received from Corn Products Co., was solubilized by first dispersing it in water to produce a 0.05% solution and then homogenizing it in a blender for 5 min. Distilled water was used in the preparation of the samples and the solutions and for all test work. Adsorption Measurements: The procedure for the adsorption density determinations was also the same as that described in the previous paper.1° The residual concentrations of the British gum and the DAC in the supernatant solution were analyzed colorimetrically by the phenol-sulf uric-acid and amine-picrate methods, respectively. The validity of the mine-picrate method for the colorimetric analysis of DAC in the presence of British gum and the analysis of British gum in presence of DAC were checked by establishing calibration curves between optical density and concentration. Streaming Potential Measurements: The cell assembly for the streaming potential measurements was similar to that described by Fuerstenau.' The streaming potential

Jan 1, 1970

By Robert E. Bush, E. S. Mardock

The objective of this paper is to present practical methods of applying radioactivity logs to problems of interest both to those engaged in evaluating fundamental reservoir data as well as to those engaged in subsurface structural work. The basic theories underlying the operation of radioactivity logging methods are briefly discussed along with some of the problems arising in the interpretation of the log. Relative methods of quantitative interpretation are described, with a discussion of relative reference lines and specific examples are given showing the application of these relative quantitative interpretation methods. To show the variation of the methods described, specimen wells penetrating formations widely divergent in point of geologic age were selected to demonstrate the application. A relative reference line is determined for the Neutron Curve and by comparison to known petrophysical data such as porosities from diamond cores, a direct quantitative relationship is developed. The application of this relative calibration curve to logs of unknown wells will permit a reasonably accurate determination of porosity in limestone and dolomite formations. Specific examples are given showing the application of these relative methods of interpretation to logs of the Smackover limestone in Louisiana, the Edwards limestone and dolomites of South Texas, and Permian dolomites of West Texas. Radioactivity logs have been used extensively by the petroleum industry for a number of years and recognition of their value has grown steadily, not only as tools to aid in the solution of specific stratigraphic problems, but also as potential sources of the basic data necessary for the estimation of net pay and reserves. The value of radioactivity logs for stratigraphic work has been pointed out in the literature,1,2,4,5,6 and now has long been recognized by the industry, but the quantitative application of the logs has advanced but little beyond the stage of a strong conviction that radioactivity logging curves will some day provide the information on such important quantities as the porosity and the liquid saturation of the formations. During the past few years the staffs of the Lane-Wells Company and Well Surveys, Incorporated, have devoted a great deal of time, thought, and experimentation to the relationships existing between radioactivity curves and the lithologic conditions encountered, and this paper is, in a manner of' speaking, intended as a progress report of this work and includes suggestions which the authors have found useful in the interpretation of radioactivity logs. The section on theory is not intended as a complete exposition of the physical processes involved, but rather as a brief introduction to the reader of these processes so that he may acquire a better understanding of the behavior of the radioactivity curves under the varied conditions encountered in normal well logging. Three relative methods for using neutron logs for the quantitative estimation of porosity in limestone or dolomite are presented. These methods are based on the comparison of logs and porosity data from wells in Louisiana, South Texas, West Texas, and New Mexico. These areas were selected because not only were there more core data available from these areas but also the majority of these data were from limestone or dolomitic zones. The correlation between core data and logs is simpler for limestones and dolomites than it is for sandstones due to the fact that sandstones are more complex than limestones and differ more widely among themselves as to composition of cementing materials, siltiness, etc. When data applicable to the various types of sandstones are available, the authors hope to present a discussion similar to this paper covering sandstones or possibly a more general discussion covering all types of reservoir rocks. The relative methods for estimating porosity which are presented in this paper fall short of the absolute method sought. However, these methods possess the advantage that they can be applied to almost any neutron log as long as the range of application is held within the limits imposed by the local lithologic conditions which prevailed during calibration, i.e., these methods are for short range application only. THE THEORETICAL BASIS FOR RADIOACTIVITY LOGGING The two redioactivity logging curves commercially available today are the

Jan 1, 1950

By J. W. Downey, S. T. Zegler

A study has been made of the occurrence of Phases having the Cr30-type structure in ternary alloys having the general composition where B cept for iron and copper all the B components are known to form binary compounds having the type structure. The occurrence of the struc-ture type in the ternary alloys was investigated using optical and X-ray metallography. The results indicate that iron can replace virtually none of the cobalt in at 900°C, but substitutes for nickel in up to the approximate composition tually insoluble in V3Ni and 2) and exhibit complete solubility. At 100 nickel can be substituted for cobalt in VSCo up to the composition solubility; and 3) in the system , two solid solutions having the type structure occur. At the same temperature, 1000°C, V3Si exhibits limited solubility for V3Co but is completely mis-cible with V3Ga. Lattice parameters have been determined for all the binary and ternary phases. The solid solutions are discussed in terms of the atomic size and electronic factors which are thought to influence the occurrence of Cr30-type phases. The binary compounds V3Co and V3Ni were found to form peritectoidally from o phases and a vanadium, the former compound at a temperature between 1000" and 1050°C, the latter between 800°and 900°C. The substitutions of nickel and rhodium for cobalt in V3Co were determined not to raise the superconducting transition of VSCo to a temperature as high as 2°K. The occurrence and stability of binary intermediate phases having the Cr30- or A15-type structure (space group o;, Pm3n) have been discussed in several recent papers . Vanadium forms the struc -ture at or near V3B stoichiometry with all the mem -bers of the cobalt and nickel groups in the periodic table and also with Au, Ga, Si, Ge, Sn, P, As, and Sb. This paper describes a survey of the occurrence of the CrsO-type structure in ternary alloys having the general composition V3(B, B') where B and B' are Fe, Co, Ni, Cu, Rh, Ir, Si, and Ga. The purpose of the survey was to clarify the connection between the position of the B partner in the periodic table and its CrsO-type phase-forming tenden~y.~,~ The survey is part of a broader program concerned with the influence of B-partner substitutions on the superconducting transition temperatures of CrsO-type compounds. The transition temperatures, Tc, of some of the ternary Cr,O-type phases found in the survey are also discussed in this paper. EXPERIMENTAL PROCEDURE The alloys were prepared by arc-melting in an A-He atmosphere and were in the form of buttons, weighing approximately 3 g. The metals used in their preparation were received from commercial sources and were in all cases 99.9+ pct pure. The vanadium was spectrochemically pure except for 800 ppm of Si, 200 ppm of Fe, and 200 ppm of Al. For study of each pseudobinary system at least seven alloys were prepared having the general compositions case of alloys containing gallium, melting losses were small, usually less than 0.3 pct of the total weight of the metals charged for melting. Melting losses were somewhat greater for gallium alloys, ranging in general from 0.9 to 5.0 pct. Ternary V-Si-Ga alloys were chemically analyzed and the results are given in Table I. The analyses show most alloys to be within 2 at. pct of the intended composition. Throughout the balance of the paper the intended compositions are used in discussing the alloys. The cast buttons were annealed within evacuated quartz capsules for times ranging from 3 to 6 weeks at temperatures between 800" and 1000°C and water-quenched. The phases present in the annealed and quenched alloys were identified by optical and X-ray metallography. X-ray diffraction photograms were made with powders prepared from the bulk specimens, by the use of a 114.6-mm-diam powder camera with copper irradiation. The lattice parameter of CrsO-type phases and their standard errors

Jan 1, 1963

By Carl F. Lutz, Robert F. Mehl

A layer of brass was formed on 0 brass using a vapor-solid reaction technique. The variation in composition with distance within the phase layer and across the a -ß interface was determined by an electron probe. The diffusivities were calculated as a function of concentration; the diffusion coefficient in brass was found to change by a factor of twenty-five over a compositional range of 8 at. pct. An explanation is proposed to account for the large change in the diffusivity, based on possible stresses in the diffusion zone; it is suggested that the concentration dependence of the thermodynamic factor might decrease the activation energy with increasing zinc content. ALTHOUGH the body of data on diffusion coefficients (D- values) in terminal solid solutions and in isomorphous systems is quite large, there is but little quantitative information for intermediate alloy phases. This paper recounts measurements of D-values for the ? phase in the Cu-Zn system. The experimental method employed consists in the forming of alloy layers and determining and analyzing the concentration-distance (c-x) curve. The experimental method employed could have been applied to several systems; the Cu-Zn system was chosen because the D-values in the a and ß phases are well known, and can thus be used for purposes of comparison. The rates of growth, of intermediate alloy layers are known for a number of systems. In nearly all cases the thickness varies parabolically with time, as to be expected if the rate of growth is controlled by the D-values. In a few cases, nonparabolic behavior has been noted.1 Nonparabolic growth may be the result of a) a variation of the composition at the phase interface with time, b) interface-controlled kinetics, c) short diffusion times coupled with long vacancy lifetimes (in vacancy diffusion),2 and d) crystal reorientation during diffusion in anisotropic systems.3 In the Al-Ni system4 and in the Al-u5 system parabolic growth kinetics are slowly approached after an initial transient period. In general those phases stable at a given temperature in a system A-B appear as separate phase layers when A and B are put in contact and given a diffusion he at-treatment. In most cases the compositions at the interface of adjacent phase layers are those read from the phase diagrams for the termini of the respective phases. This discontinuity in concentration is taken as independent of time, and the growth of one phase at the expense of another is assumed to be independent of interface kinetics, i.e., the rate of interface movement is controlled by volume diffusion in the phases concerned. wagner6 has given many solutions for multi-phase diffusion processes, assuming that the chemical diffusion coefficient, D, is independent of concentration, as have others. Jost7 has pointed out that the familiar Boltzmann-Matano solution is as valid for a (c-x) curve exhibiting concentration discontinuities at phase boundaries as for the usual single-phase case. Heumann and associates8,9 have applied this solution to the multi-phase case, but lacking concentration data within the several layers were forced to assume linear concentration gradients, thus calculating only average D-values. The purposes of the present study were: 1) to determine the dependence of D on concentration, 2) to calculate the intrinsic diffusion coefficients D?Cu and D?Zn, 3) to establish the time-law for the movement of the interface, 4) to determine the concentration limits at the ß-? interface, and, 5) to attempt to clarify the mechanism of diffusion. EXPERIMENTAL PROCEDURE The ? phase is exceedingly brittle; conventional solid couples and conventional sectioning methods were thus inapplicable. Vapor-solid couples were accordingly employed. Unfortunately the equilibrium vapor pressures of Zn for the ? phase are unknown; to escape this awkwardness, samples were enclosed in a capsule containing powder of an alloy of known composition, sufficiently large in quantity as to be effectively an infinite source, maintaining the concentration of Zn at the sample surface constant with time. The sources of Zn-vapor which can be employed in reaction with Cu, or a brass, or ß brass, to form a layer of ? brass satisfactorily wide in concentration range, are alloys of the phases ?, or ? + E or ? + d (depending on the temperature).

Jan 1, 1962

By K. R. Evans

The yield and fracture characteristics of a Ti-8 pct A1 alloy have been examined at room temperature as a function of exposure temperatures to 1700°F. Em-brittlenzent of the alloy is observed to occur following exposures below 1280°F, the critical temperature for formation of ordered Ti3Al particles. Presence of Ti3Al particles results in an increase in the yield and flout stresses which, for a given exposure time, are a maximum at the critical temperature. Embrittlement is attributed to the occurrence of plastically induced fracture controlled by the increase inflow stress. This interpretation is compatible with the decreasing ductility and increasing crack popagation rates observed with increasing exposure time below the critical temperature. Slip line observations and measurements of the gain size dependence of the yield stress indicate that the slip character of the alloy is not influenced by exposure treatments below the critical temperature. ThE potential usefulness of Ti-A1 alloys in structural applications has prompted considerable interest in studies of their microstructure and mechanical characteristics. The relatively recent surge of interest in the system and at the same time its complexities are indicated by the fact that despite numerous recent efforts14 there has not even been general agreement upon a phase diagram for the system. However, most of the Ti-A1 alloys of commercial interest range in aluminum content from 5.0 to 8.5 wt pct where most investigators achowledge the existence of the ordered Ti41 phase. Goldak and parrs confirmed the existence of Ti41 from X-ray diffraction analysis of the stoichiometric composition while Blackburn6 has determined its presence in commercial Ti-8 pct A1 alloys by electron diffraction analysis and dark field transmission microscopy. The embrittlement of Ti-8 pct A1 alloys was initially reported by Crossley and carew7 who showed that aging in the temperature range of 750" to 1110°F resulted in extreme brittleness. This behavior was later confirmed and correlated by Soltiss to the presence of long-range order in the commercial Ti-8 pct Al-1 pct Mo-1 pct V alloy (Ti-8-1-1) which exhibited anomalous creep and yield strength behavior at 950°F. This investigation was designed to study the mechanical characteristics of a binary Ti-8 pct A1 alloy in order to further examine the nature of the embrittlement behavior reported for the alloy system. EXPERIMENTAL PROCEDURE A Ti-8 pct A1 binary alloy was obtained from the Wah Chang Co. in the form of 0.050 in. sheet. The chemical composition of the alloy is given in Table I. Heat-treatment of the alloy was conducted in evacuated vycor capsules for the tensile sDecimens (1.25 bv 0.25 in. gage section) and in evacuated stainless steel jackets for the crack growth-rate panels. All specimens were annealed at 1700°F for 24 hr and water quenched before an exposure at elevated temperatures. Tensile testing was conducted at room temperature in an Instron testing machine equipped with a pushbutton control for instantaneous control of the cross-head motion. In this manner the change in stress, Aa, accompanying an increase in strain-rate by a factor of 10 was measured immediately after yielding. The crack growth-rate panels used were 3 by 18 in. with a precrack 0.33 in. long cut into the center of the panel. The panels were cycled at a maximum gross stress of 40,000 psi at a maximum to minimum tension stress ratio of 20. Cycling of the specimens was continued until the crack propagated the width of the panels. The crack length was intermittently measured during slow crack growth. EXPERIMENTAL RESULTS Correlation of Embrittlement to the Critical Temperature for Ordering. Blackburn6 has found that the critical temperature, T,, for the formation of Ti41 in a Ti-8 pct A1 alloy with an interstitial content on the order of that given in Table I is approximately 1245°F. The relationship between the ductility of the binary alloy used in this investigation and T, was estimated from tensile tests on specimens which were exposed for 24 hr at various temperatures followed

Jan 1, 1970

By C. S. Matthews, M. J. F. Rosenbaum

The purpose of thir work wax to lcarn it~lzut infori~lation could he obtained from various typs of pilot water floods and to attempt to find the optunum pilot patter11, for a revervoir which had previously been depleted by a solution gas drive. The study was made in the laboratory with mathemetical methods a dynamic analog and a potentiotnetric analog. Results werp tested against the field llistorics of a nrrnlber of pilot water floods. At a reasonable valrre of currzulative injection, the total production rate for the one-injector five-spot should reach about 6.5 per cent of injection rate, and for a four-injector five-spot, about 9 per cent. Accurate estimates of ultimate recovery cannot be made on the basis of such snzall prorluction rates. However, with a pilot composed of nine ir1jector.s and 16 producers the production rate is approximately 50 pcr cent of injection rate at a reasonable value of camulative injection. Sonle inforn~ation for extended performance predictions might he obtained from such a large pilot. These conclusions were drawn on the basis of results obtained for unit mobility ratio, and a sturly using tlre potentiometric analog was made of the effect of other mobility ratios to determine the range of applicability of these predictions. For the four-injector, five-spot pilot with the ratio of production to injection rate (before water breakthrough) is about twice that for with it is about two-thirds; and with M0= 10, it is about one-third For high mobility ratios, it was found that the production rate increased considerably as water-cut increased. These result can be used to modify, qualitatively, the inter.pretntions based on curves for the unit rnobilit\. ratio CaSeS. It was found that the maximum ratio of production rate to injection rate obseriled in field pilot floods was of rhe scime order as that prerdicted by these methods. The time required to reach thisr maximum did not generally agree with the time predicted for a homogeti~orir reservoir. The differcrlce between predicted and observed time of response gives an indication of the permeability profile and of the condition of the producin,g wells. Pilot water floods of the pattern type are generally carried out in reservoirs which have been depleted by solution gas drive and are at low pressure. Under these conditions, oil and water can be considered incompressible. It is assumed that, as the water is injected, an oil bank forms ahead of it and that there is a distinct interface between the water zone (or bank) and the oil zone (or bank) and between the oil zone and the region ahead of the oil zone. It is further assumed that only gas is mobile in the unflooded (gas) region, only oil is mobile in the oil bank and only water is mobile in the water bank. The saturations and the mobilities associated with each zone are assumed uniform. We idealize our reservoir to be homogeneous, horizontal and of constant thickness. Effects of gravity within the producing layer are assumed negligible. If the actual time-dcpendent flow problem is approximated by a acries of steady-state problems. the potential and stream function in the oil bank and water hank satisfy Laplace&apos;s equation in two dimensions. We can therefore use a poteiitiometric analog of this system. Potentiometric models have yielded uscful results in this laboratory&apos; and clsewhere in the study of a variety of secondary recovery problems. For the case where M = I, we generally prefer to use theoretical mcthods as well as a simpler dynamic analog. Except where otherwise noted, the ratio, side of five-spot/wellbore radius. is taken to be 3,600. a figure which corrcsponds to a normal-size wellbore in a 10-acre well spacing. THEORETICAL EVALUATION OF VARIOUS PILOT PATTERNS, Mw0 = 1 <&apos;he theoretical models which we used to examine the performance of various pilots are shown in Fig. 1. Image theory was used to determine the ratio of production rate to injection rate as a function of the volumc of the flood. The ratio of production rate to injection rate was chosen because this is an easily measurable quantity which is characteristic of a pilot

By Raymond L. Orr

Calorimetric measurements have been made of the heats of solution of gold axd indium in a number of liquid tin-rich alloys at a temperature of 705°K. Relative partial molar enthalpies of gold were determined as a function of dilute solute concentrations in the binary Au-Sn system and in the ternary Ag-Au-Sn and Au-In-Sn systems. Relative partial molar enthalpies of indium were determined for dilute solute concentrations in the In-Sn, Ag-In-Sn, and Au-In-Sn systems. Through application of the interaction coefficient concept introduced by Wagner and more recently extended by Lupis and Elliott, ualues have been obtained for the Au-Au, Ag-Au, Au-In, and Ag-In enthalpy interaction coefficients in liquid tin. The results are inte@reted in terms of solute atom distributions through comparisons with the predictions of dilute solution models. INTEREST in the thermodynamic behavior of dilute liquid alloys stems from two primary sources. From a practical viewpoint, it is often of importance to know or to be able to predict the effect that one solute will have on the thermodynamic properties of the other solutes in a multicomponent system. Studies of dilute solutions may also be rewarding from the theoretical point of view. Some of the difficulties arising from the more complex interactions possible in concentrated solutions are avoided, leading to easier interpretations in terms of solutibn models and bonding energies. For example, in a binary alloy the limiting values of the partial molar properties of the solute represent the case for which each solute atom is completely surrounded by atoms of the solvent, and no other interactions are possible. Solute - solute interactions in dilute solutions are conveniently treated by the interaction coefficient concept of ~agner.&apos; Using a Taylor series expansion for the logarithm of the activity coefficient, In yi, of a component, i, in a solution consisting of dilute solutes with atomic fractions xi, xj, xk, and so forth, in a solvent, s, and neglecting the second- and higher-order terms, Wagner obtained the expression: Where Wheyz is the limiting value of yi in the pure solvent, s. The interaction coefficients, e:, e:, and so forth, are defined by: Since yi is related to the excess partial molar Gibbs energy of component i by GfS = RT In yi, E: is re- ferred to as the "Gibbs energy interaction coefficient". Lupis and Elliott~ extended Wagner&apos;s treatment to the relative partial molar enthalpy, aHi, and the excess partial molar entropy, qS. They defined the enthalpy interaction coefficient as: and the excess entropy interaction coefficient as: leading to expressions similar to Eq. [I]: The three interaction coefficients are related by? The self-interaction coefficients, E:,qf,and at, represent the effects of interactions between atoms of component i in solvent s; €3, q{, and 03 represent the effects of interactions between i and j atoms in solvent s; and so forth. From the Maxwell-type relationships between partial molar quantities, it may be shown1&apos;2 that e{ = ej, r}\ =tj), and ai - crj. Experimental determination of the interaction coefficients requires extremely precise measurements of the appropriate properties as functions of solute concentrations in very dilute regions. Few such data exist for intermetallic alloys, even for binary systems, because of experimental difficulties. This is especially true with respect to enthalpy data for dilute alloys. Examination of the compilation of data for binary alloys by Hultgren, Orr, Anderson, and ~elle~~ reveals that determination of limiting values of &fii(Xi =0) often requires extrapolations to infinite dilution from xi = 0.05 to 0.10. Direct measurements of the enthalpy interaction coefficient, qi, for multicomponent systems are virtually nonexistent. This quantity is of course subject to direct calorimetric measurement, but its determination must be limited to cases where high experimental precision is possible. The heats of solution of gold and indium in liquid tin can be measured with relatively high precision, which makes determinations of 73 involving these metals as the measured solutes experimentally attractive. This paper presents the results of such determinations of the Au-Au, Ag-Au, Au-In, and Ag-In enthalpy interaction coefficients in liquid tin. MODELS FOR DILUTE-SOLUTION BEHAVIOR Random-Solution Behavior. In the quasi-chemical treatment of solutions, only nearest-neighbor bonds are considered, and a composition independent value

Jan 1, 1967

By R. J. Burgess, A. R. Ramey, A. R. Adams

During interpretation of pressure buildup tests on gas wells in a tight dolomite gas reservoir, peculiar behavior was noticed. Two straight lines were apparent. Effective permeability to gas taken from either straight line was about the same, and the Miller-Dyes-Hutchinson dimensionless time check for the straight line was proper for both straight lines. Geological data indicated the likelihood of scattered trending fractures in the reservoirs. Since the first straight Iine yielded permeability values close to the geometric mean permeability from core analyses, it was postulated that the reservoir model was that of an acidized well completed in the tight dolomite, but that widely scattered hairline fractures caused the mean permeability of the reservoir distant from the well to be higher than the matrix permeability. Because all other studies of fractured reservoirs to the authors&apos; knowledge assumed that the fracture matrix was dense enough to communicate directly with the well, no interpretative methods were available. The Hurst line-source solution for a radial change in permeability for interference between oil reservoirs was adapted to pressure buildup testing. The result indicated that the first straight line should yield the proper matrix permeability and wellbore skin effect. The second straight line may be extrapolated to obtain static pressure. The time of bend between the straight lines was used to estimate distance to a fracture. Application to field test data is shown. It is believed that the methods developed and the case history presented will add to present tools available for pressure buildup interpretation. Introduction Since the pioneer studies by Miller, Dyes, and Hutchin-son1 and Horner&apos; in 1950 and 1951, well test analysis has become recognized as one of the most powerful tools available to both production and reservoir engineers. Well test analysis serves as a logical basis for well stimulation and completion analysis, and for long-term reservoir engineering. Since the early 19501s, much effort has been placed on the development of well-test analytical methods. Reservoir and well conditions of increasing complexity have been considered systematically to provide the analyst with a catalog of causes and effects. Matthews and Russella state that some 200 papers dealing with this subject have been published in the last 35 years. Developments in well test analysis appear to have originated in one of two ways. Either a physically realistic field condition was anticipated and analytical solutions for the condition achieved, or anomalous field test behavior was recognized and interpretative methods sought for the anomaly. In recent years, it has appeared that the latter has inspired an increasing number of studies. The analyst today finds an increasing number of known cause and effect studies available for well test analysis, the classic of which is that of finding the specific flow problem that generated the answer — the well behavior. Although it may be impossible to achieve this goal uniquely, the analyst often is able to select a useful interpretation that combines all known performance and geologic data — or to show that various logical alternatives would not significantly affect the interpretation. During a recent reservoir study, we observed gas well test behavior that did not appear to fit behavior described previously. Although it cannot be said that we have found a unique interpretation, we shall present in this paper the peculiar behavior observed, and describe the reservoir and interpretative methods developed. Reservoir Description The subject gas reservoir is a 9-mile-long, narrow dolomite reservoir lying within a limestone of Ordovician age. (See Fig. 1.) The dolomitized rock in the field consists of dark brown to buff, dense to coarsely crystalline, vugular dolomite containing numerous hairline fractures, many of which may have been closed in the reservoir and parted when cores were brought to the surface. Larger fractures are also apparent in core, but usually are filled and sealed with euhedral dolomite crystals. Portions of the north flank of the reservoir are known to be cut by a sealing fault downthrown to the north. Gas wells located near the fault have higher open flow potentials than those more distant from the fault. This is believed to be a result of higher permeability near the fault due to more extensive and open fractures. Detailed coring and core analysis have been performed on several of the wells in this reservoir. Fig. 2 presents permeability variation&apos; plots for both horizontal and vertical

Jan 1, 1969

By L. D. Clark

Pay-out, the ratio of capital expenditure to annual cash return can be very revealing when employed to gage the merits of a proposed mining venture. It is a quantity, numerically but not physically equal to a factor, by which cash return may be discounted to equal required investment. The fewer the pay-out years, the greater the average annual earning power of the project. Considerable material has been written in the past about the most important and difficult problem mining management faces in evaluation of a property: the optimum production rate for the venture. What daily capacity should be adopted for the proposed operation that it may be the most rewarding to those underwriting it? H.C. Hoover has said, "The most important objective is the least cost per ton mined; and minimum working costs can only be gained by the most intensive production." Theoretically and practically, the quicker the ore is removed, the more profitable should be the venture because of the saving in fixed charges, the consequent lower unit costs and the interest unearned by the profit from the unmined ore. Yet, such performance will be tempered by policy and a restraint imposed by the ratio of capital expenditure to annual cash return. * The &apos;Annual net profit after taxes but including depreciation and depletion allowances. former will be based upon an analysis of the economic climate anticipated, with its many ramifications including the demand for the product, prices, tax laws, the conduct of labor and related wage scales. The variables and intangibles involved in estimating the optimum production rate for a mine do not readily lend themselves to mathematical relationships or equations and the problem can become complex indeed. The more readily applicable and relatively faster appraisal method will be used which, in addition to being reasonably adequate in most cases, will serve as a guide, should a more expanded and detailed estimate be desired. The first question is what is company policy with respect to the rate of investment return? This will depend on that significant period of time referred to as the pay-out, which can be defined as the estimated interval during which capital investment is returned through application of annual cash return to its recovery. Expressed another way, it is the ratio of capital expenditure to the annual cash return. For example, if the capital investment is $C and the annual cash return is $A (after Federal tax), then $C/$A = the pay-out period in years. That is to say, if $C = $1,500,000 and $A = $214,000, then which is the mathematical expression for the period of time it takes to recover the funds originally invested in a mining enterprise. The relationship yp = $C/$A can be useful — an expression which requires only the significant tern yp to be fixed; in other words, the long range investment policy. For what is the pay-out period but an expression of that policy in terms of the speed, within practical limits, with which an individual or company may want to recover capital expenditure? A policy by which pay-out will be fixed is imperative. This ratio must lie within relatively narrow limits governed by what is economically feasible. It cannot be too low, rendering the ratio impractical or absurd, nor too great, delaying the return of capital for reinvestment beyond a commensurate interval. What pay-out will govern this policy? Federal corporate taxes would seem to present the best measure. Consider mining in Canada where new mines are exempt from Federal income tax for 3½ yr from date of first production. This exemption expressly allows The Act states: "A corporation . . . i s not required to include the profits . . . for the period of 36 months commencing with the day on which the mine came into production in reasonable commercial quantites." a company to recover capital expenditure during the early stages of production. With such an incentive, it is logical to strive for as much capital redemption as possible during this period. Thus, 3½ yr would be a major contribution to the pay-out in Canada. Furthermore, it generally takes from 1½ to 3 yr to develop

Jan 1, 1963

By Rex B. McLellan

A simple model for dilute interslitial solid solutions is set up which enables a solubility equation for the equilibrium between the solid solution and the gaseous solute to be deduced. This solubility equation is used to estimate the partial thermody -namic functions of Ag-O and Fe-N dilute interstitial solid solutions from the measured equilibrium between these solutions and the gas phase. It is shown that the partial excess entropy of the solute atom in solution is a vibrational entropy which is due Principally to the oscillation of the interstitial atom and does not arise from electronic or elastic interaction between the solute atoms and solvent matrix. In this work measurements of the equilibrium between dilute solid interstitial solutions and a gaseous phase are used to deduce the important thermody-namic functions of the solid solution with the aid of a theoretical solubility equation formulated from a knowledge of the thermodynamic functions of the gas and a simple model for the solid solution. The quantity of principal interest which is deduced from the equilibrium data is the change in vibrational entropy occurring when a solute atom (u) is placed in an interstial site in the solvent (u) lattice. This paper forms part of a more general study in which the properties of condensed phases are deduced from measurements of the equilibrium between the condensed phase and a gas. Previous investigations have dealt with the equilibrium between krypton and liquid metals,&apos; a pure metal and its vapor,&apos; and dilute substitutional alloys and the vapor,3 and the subject has been popularly reviewed by McLellan.4 In the latter investigation3 the vapor pressures of very dilute Cu-Ag and Cu-Au alloys were measured with a Knudsen cell technique over a large range of temperatures and the analysis of the vapor-pressure data showed that the relative partial excess entropies were large and positive [ds= -Sudk = 30 for Au-Ag alloys and 150 for Cu-Au alloys; these values should be compared to unity, the value assumed for these exponentials in the quasi-chemical theory of solutions]. For many interstitial solutions experimental data is available for the equilibrium between the solution and a gaseous phase, and this can be used to deduce the vibrational entropies of the solute atoms in solution. The general method employed is to calculate the chemical potential of the solute atoms in the gas and equate this to pi, the chemical potential of solute atoms in the solid, which is deduced from a simple model set up for the dilute interstitial solution (in which the solute atoms act as bound oscillators in interstitial sites). This enables a theoretical solubility equation to be set up. In the case of Ag-O and Fe-N solid solutions the solubility c, is found to vary with temperature according to a relation of the type, where PU2 is the pressure of the O2 or Np molecules. Essentially, the theoretical solubility equation enables the parameter A(T), which gives the vibration entropy, and the parameter AH, which gives the energy of solution of a solute atom, to be estimated from the measured variation of solubility with temperature. The solutions treated are dilute enough to enable solute-solute interactions to be neglected so that the partial energy and excess entropy of solution E, and GS are not functions of composition and the configurational entropy is that of a random solution. Large positive values have been found for sxSu this quantity has not been given sufficient consideration in recent work on interstitial solutions and it is felt that the partial thermodynamic quantities of very dilute solutions should be understood before the thermodynamics of concentrated solutions can be fully appreciated. EXPERIMENTAL DATA 1) The Silver-Oxygen System. The measurements of Steacie and Johnson,= using silver foils, indicate that there is a pronounced minimum in the solubility vs temperature curve for O-Ag solutions. Eichenauer and Miiller6 have recently redetermined the solubility of oxygen in silver using a method developed in the investigation of metal-hydrogen systems.7 The solubility determinations were carried out on compact specimens of differing shapes and sizes and the results indicate a much lower solubility than was obtained by Steacie and Johnson with no minimum at 400°C. Subsidiary experiments showed that the erroneous results of Steacie and

Jan 1, 1964

Plans are now being made for the formation of the American Meteorological Society, which has for its object the advancement and diffusion of the knowledge of meteorology and climatology said the broadening of their applications in public health, agriculture engineering, industry and commerce. Information regarding the society may be obtained from Charles F. Brooks, Weather Bureau, Washington, D. C.

Jan 12, 1919

"Acta Metallurgica" Dennis Carney, &apos;59 Alfred Noble Joint Prize Committee F B Foley, Dec &apos;61 American Association for the Advancement of Science F T Agthe, Dec &apos;59, William L Fink, Dec &apos;60 American Geological Institute Arthur Montgomery, Oct , &apos;59, F C Kruger, Oct &apos;60 American Power Conference J P Weir, T D Hess American Society for Testing Materials

Jan 1, 1959

The Institute conducts jointly with the American Society of Civil Engineers, American Society of Mechanical Engineers and American Institute of Electrical Engineers, certain activities as listed below, and is joint owner with them of certain properties. United Engineering Trustees, Inc. When Mr. Carnegie made. his gift ?for the erection of a suitable home? for the engineering societies,

Jan 1, 1943