Search Documents

By E. J. Whittenberger

OVER the past two decades, the Cr-Ni stainless steels, popularly termed 18-8 steels, have been used in ever increasing amounts in the aircraft, automotive, chemical, transportation, and building industries.' The contribution of nickel to these steels is associated with its strong austenite forming tendencies which assure good hot and cold forming characteristics, and with its beneficial influence upon corrosion resistance, especially in oxidizing acids. The adjustment of the chromium and nickel contents has been used advantageously in controlling the rollability and the response of the mechanical properties of these steels to cold reduction. With the advent of the jet age and the government stockpiling of nickel, considerable emphasis has been placed upon the development of satisfactory low nickel or nickel-free substitute austenitic stainless steels, especially for nonmilitary applications.2 Fer-ritic 17 pct Cr (AISI Type 430) stainless steel has been effectively substituted for the austenitic grades in applications with mildly corrosive exposure. However, the limited formability and ferromagnetic behavior of this grade do not permit its satisfactory use for many applications. To achieve better formability in a nenmagnetic steel and conserve nickel, a number of low nickel substitute austenitic grades of stainless steel have been developed in recent years. In most of these steels, manganese and nitrogen have been substituted for a portion of the nickel content, for example, 17 pct Cr-4 pct Ni-6 pct Mn (AISI Type 201), 18 pct Cr-5 pct Ni-8 pct Mn (AISI Type 202), and 16 pct Cr-1 pct Ni-17 pct Mn, all of which contain approximately 0.15 pct N.1 The precipitation of ferrite when large ingots of these Cr-Ni-Mn-N steels are heated to temperatures high enough for conversion to slabs on conventional universal slabbing mills has seriously affected the hot workability of these steels. This has been especially true in the case of the 16 pct Cr-1 pct Ni-17 pct Mn (sometimes referred to as 15 pct Cr-1 pct Ni-15 pct Mn) composition." Because it is possible that little, if any, nickel will be available for nonmilitary stainless steel applications in the event of a national emergency, a need has existed for a nickel-free austenitic stainless steel containing hot and cold forming characteristics similar to 18-8 steels and corrosion resistance at least comparable to the 17 pct Cr ferritic steel. The aforementioned deleterious effect of ferrite upon the hot working characteristics of the 16 pct Cr-1 pct Ni-17 pct Mn, steel indicates the importance of establishing the austenite-austenite plus ferrite phase boundaries as the first step in the development of nickel-free or low nickel substitute steels. This paper presents the data collected in an elevated temperature constitutional study of the Cr-Ni-Mn-N system at the South Works of the United States Steel Corp. Experimental Procedure The 300 compositions used in the investigation were melted in a 26 Ib induction furnace and cast in 3 14 in. diam by 18 in tall hot-tcpped ingot mo1ds.

Jan 1, 1958

By J. D. Edwards, C. S. Taylor, A. S. Russell

Solubilities and densities are reported for alumina hydrates in NaOH solutions under the conditions of the Bayer process employed to purify alumina for aluminum production. The equilibrium constants for reactions to form A102- accurately correlate the effects of NaOH concentration on the solubilities; the temperature coefficients of the equilibria lead to heats of solution of 7.34, 4.76, and 5.24 kcal for the a trihydrate, a monohydrate, and ß trihydrate, respectively. Moderate calcination does not change the solubility of the a trihydrate but increases that of the a monohydrate. At solution temperatures above 100°C, the trihydrates transform rapidly to a monohydrate. Hydro-thermally produced a monohydrate is the stable phase above 20°C. CORNERSTONE of the aluminum industry, the Bayer process for alumina production is based on the difference in solubility of hydrated alumina in NaOH solutions between 170" and 40°C. Solubilities and densities in this system were determined thirty years ago by M. Tosterudl under the direction of J. D. Edwards and C. S. Taylor. The solubility data, which still appear more concordant than those in the literature, are employed to sort out the complex equilibria in this system. The nomenclature for the alumina hydrates is that presented in The Aluminum Industry' and more recently summarized in Alumina Properties.3 a trihydrate is the purified phase analogous to gibbsite, a monohydrate is similarly akin to boehmite, and ß trihydrate is sometimes known as bayerite. Literature Goudriaan4 reviewed the early literature on alumina in NaOH solutions and presented data on the solubility at 30°C of several forms. The gel precipitated from aluminum sulphate or chloride with ammonia and dried at 130" to 140°C had the highest solubility but was unstable, its solubility being cut to one-tenth on standing in NaOH. The solubility of the gel was decreased one-third on calcination at 300" to 400°C, while that of the gel transformed in NaOH at room temperature to a crystalline trihydrate was unchanged on calcination. The preparation produced by slow hydrolysis of sodium aluminate solution with CO, in the air gave solubilities in rough agreement with later values for a trihydrate. The solubility of this form was increased slightly by the calcination. Fricke and Jucaitis5 extended the work to 30" and 60°C with a trihydrate. They also gave solubilities for ß trihydrate (bayerite b), although the residue belonging to the left branch of the solubility curve corresponded to a trihydrate. The residues at high NaOH concentrations were mono and trisodium aluminates, the latter being 3Na2O . AL2O3 • 6H2O. Solubilities of a trihydrate at 95°C and of a monohydrate at 150" and 200 °C come from the work of Magarchak.6 a trihydrate transformed to a monohydrate above 95°C. A few measurements on the solubility at 25°C of an alumina trihydrate prepared by slow hydrolysis of NaAIO, solutions were presented by Sprauer and pearce.? Their analyses showed the monosodium aluminate to have the composition Na2O.Al2O3-2.5H2O.

Jan 1, 1956

By R. C. Buehl, M. B. Royer

A three ton per day blast furnace using blast temperatures up to 2200°F was operated to recover manganese from open-hearth slag and manganiferous iron ore. The spiegel product containing 12 to 24 pct Mn was blown in a basic converter to high manganese oxide slag as described in the paper which follows this one. HE steel industry, which uses over 900,000 short tons of contained manganese yearly, depends on the maintenance of supplies of manganese from foreign sources such as India, Gold Coast, and Union of South Africa. Domestic ores furnish less than 10 pct of the yearly requirements of metallurgical ores and, unfortunately, the United States has no large, or even moderate, grade deposits that could supply a major portion of the requirements for many years. It may be necessary to obtain manganese from low grade materials, even though the cost is appreciably higher than when imported ores are used. An American Iron and Steel Institute questionnaire prepared in 1949 revealed the startling fact that open-hearth slags contained about as much manganese as is imported annually. The quantity of slag produced each year by integrated steel plants (not including cold-melt shops) and the manganese contained in the slag follows: Flush slag, 4,500,000 net tons a year containing 408,000 net tons Mn; tap slag, 7,230,000 net tons a year containing 364,000 net tons Mn; for a total of 772,000 net tons Mn. Some of this slag is returned to blast furnaces but about 75 pct would be available for the recovery of manganese. In several decades, when many of the present sources of high manganese ores have been depleted, open-hearth slag and manganiferous iron ore may become the major source of the manganese required for steel production. In 1948, manganese-ore imports from the U.S.S.R. were 427,000 net tons or 34 pct of the foreign ore. Imports from this source were only 81,000 tons in 1949. It became evident that adequate stockpiles of manganese could not be accumulated for many years. The Bureau of Mines initiated an extensive research program on methods for increasing domestic production of manganese and entered into a cooperative agreement with the American Iron and Steel Institute for recovering manganese from open-hearth slags whereby the Institute provided additional research funds and trained operating personnel. Description of Process and Equipment Numerous pyrometallurgical and hydrometallur-gical processes and combinations of the two can be applied to the recovery of manganese from open-hearth slag and manganiferous iron ore. The process being developed at the Pittsburgh Station of the Bureau of Mines consists of: 1—Reduction of open-hearth slag in a blast furnace to recover the iron and manganese as spiegel-eisen with 12 to 24 pct Mn. 2—Selective oxidation of the manganese from the blast-furnace metal in a basic-lined converter to produce a high manganese slag with up to 60 pct Mn content, which is a synthetic ore for the production of ferromanganese. This process has the advantage over other processes in that the equipment which would be used, such as blast furnaces and converters, has been highly

Jan 1, 1953

MARSHAL Foch has been made an honorary member of the four national American societies of civil, mining and metallurgical, mechanical, and electrical engineers. The governing bodies of these societies, aggregating 45,000 members, conferred this signal honor in expression of the appreciation of American engineers for the unmatched services of this master of engineering principles. At Engineering Societies Building, in New York City, on Tuesday afternoon, Dec. 13, the presidents of the four societies presented one beautifully engrossed certificate of honorary membership in the four societies. The auditorium was filled so that not even standing room was left, more than a half hour before the cere-monies began, and the main entrance on the street had to be closed. J. Vipond Davies, president of the United Engineering Society, made the opening address. Col. William Barclay-Parsons, 'who was commander of the first engineer regiment to go abroad, addressed Marshal Foch in French. Colonel Parsons said: The art of engineering was defined a long time ago as "the art of directing the great sources of power in nature for the use and convenience of man." No better definition can be found today. Of all the sources of power in nature, the greatest, the most valuable, and at the same time the most difficult to direct, is the energy of man himself. He who can direct human energy and turn it to the service of mankind is a great engineer. You, Marshal, have directed a greater mass of human energy than any other man has ever done. And you have successfully directed this mass for the highest uses of mankind, in that you by its aid have preserved for him one of the most precious of human possessions-liberty-liberty not only for your own illustrious country, but for all the nations of the world. The four national engineering societies, of the United States now desire to make record of their appreciation of this fact and to convey to you an expression of their most profound admiration for the great leader of men by conferring on you honorary member-ship in all the societies, the highest honor in their gift and one hitherto never conferred on a single individual. Four thousand members of these societies were enrolled in the armed service of the United States, the greater part of whom had the glorious distinction to serve the common cause in France under your orders. They heard the voice and they saw the hand of the master as he led them through battle to victory. Now we desire that you will still continue to lead us, but in peace, by permitting us to inscribe your name at the head of our roll of honor, where it will be, as your deeds have been, an example to us to do better work, and where it will remain forever a noble inspiration for all future generations. Marshal, in the name of those members of the societies who served under your orders and particularly .in the name of those who fell on the field of honor in France, I salute you.

Jan 1, 1922

By P. F. Gnirk, J. B. Cheatham

An experimental investigation has been made to study the effects of tooth angle and confining pressure on the force required for indentation of dry rock samples under confining pressure. In these experiments static single-tooth indentations were made on two standstones, a limestone, a schist and a slate under confining pressures of 5,000 to 15,000 psi. Sharp wedge-shaped teeth with included angles ranging from 30°to 105°were used. In all cases the force-displarenzent curves are approxinlately linear for rocks tested under confining pressure, as contrmted with the discontinuous curves obtained for silnilar rocks at atmospheric conditions. Photonzicrographs of thin sections through the craters indicate very little evidence of chip formation during indentation. In general the experimental data lie between calculated values for perfectly rough and perfectly smooth tooth-rock interfaces. INTRODUCTION The variables associated with ctrilling at depth are numerous and, in many instances, are not easity isolated and controlled. Also, many of these variables are interdependent; however, if the variables which are sufficiently independent of each other are held constant and are appropriately introduced, the dependent variables can be more easily studied and evaluated. It is the purpose of the present investigation to study experimentally the simplest case of bit tooth-rock interaction. In essence, the experiments have involved the static loading of sharp wedge-shaped tools on the surfaces of effectively semi-infinite dry rock samples subjected to confining pressures. During this investigation the following quantities have been maintained constant: 1. Pore pressure: atmospheric (i.e., the rock is dry). 2. permeability: although the rocks may be permeable, they are "jacketed" in such a manner that the fluid is not permitted to flow through them. 3. Temperature: 75F. 4. Rate of loading: essentially static (approximately 0.002 in./second). 5. Bit tooth: a sharp wedge-shaped tooth loaded normal to the rock surface. 6. Rock surface: smooth and flat. 7. Drilling fluid: hydraulic oil. In addition to the above conditions, the rock surface was free of a layer of cuttings. There was no indexing to previously indented surfaces, and the influence of corners of the borehole was neglected because the rock samples were effectively semi-infinite. The following quantities have been varied, and the resulting effects have been studied: 1. Rock a) Type (e.g., limestone, sandstone, etc.). b) Mechanical properties ) Necessarily dependent c) Porosity on type of rock. 2. Bit tooth (included angle of wedge-shaped tooth). 3. Depth of penetration. 4. cobfining pressure. On the basis of laboratory experiments which have shown that many rocks exhibit ductile behavior at confining pressures corresponding to depths usually reached during drilling,'.' a theory has previously been advanced which predicts the force required for penetration by a single sharp wedge tooth into a ductile* material.' The material is assumed to be isotropic, homogeneous and rigidly plastic (no elastic deformation) and to obey the Coubomb yield criterion (Figs. 1 and 2). Equations governing the force required for penelration are given for two extreme cases:** 1. A smooth, perfectly lubricated tooth-rock interface (fridionless boundary), in which the solution gives a minimum value for the penetrating force: in which F = force of the tooth, b = length of tooth edge,

By E. T. Turkdogan

In this theoretical paper, a transport-reaction mechanism is suggested for the enhancement of the rate of vaporization of metals, or other materials, brought about by the process of convection and condensation. Based on theoretical reasoning it is predicted that, when there is a temperature gradient surrounding the heated object, a slight increase in the rate of vaporization brought about by natural convection is enhanced further as a result of condensation of the vapor close to the surface of the object. In order to derive the effective vapor-concentration profile, consideration is given to the super saturation of the vapor necessary for the homogeneous nucleation of the condensed phase from the vapor. For the formulation of the rate equation based on this mechanism, adequate information should be available on the transport properties of gases and vapors at elevated temperatures and the method of calculating nucleation pressures of the vapor. The methods of deriving such data are discussed in the paper and a rate equation is calculated for the vaporization of iron in helium for various temperature gradients in the boundary layer. Considerations are also given to the effect of oxygen on rates of vaporization of metals under isother ma1 and nonisotherma1 conditions. THE study of the methods of enhancement or retardation of basically transport-controlled vaporization reactions is of theoretical interest with possible practical implications. There are several ways of bringing about such effects. For example, Turk-dogan, Grieveson, and Darken1 demonstrated that the rates of vaporization of metals under isothermal conditions were increased by several orders of magnitude, up to the maximum rate attainable in vacuo, by introducing some reacting gas into the inert atmosphere surrounding the metal. Such an effect is brought about by the interaction of the counter-diffusing reacting gas and metal vapor in close proximity of the metal-gas interface. Another case which is often experienced in practice is that of vaporization affected by natural convection. Although several theoretical and experimental studies of this problem have already been made, no detailed consideration has been given to the possible effects of condensation of the vapor in the boundary layer on vaporization rates, which constitutes the subject matter of this paper. BASIC CONCEPT OF ENHANCED DIFFUSION-LIMITED VAPORIZATION When a heated object, for example a metal sphere, is submerged in a fluid medium, heat is transferred from the surface of the object to its surroundings by four simultaneously occurring transfer processes: i) free-molecular conduction at the gas-solid interface over the distance equal to the mean free path of the gas, ii) conduction and convection through the fluid-dynamic boundary layer, iii) latent heat of mass transferred, and it!) radiation. The free-molecular conduction becomes pronounced only when the total pressure in the system is very low, e.g., below 1 mm Hg. Therefore, this term may be neglected for ordinary pressures. At low mass-transfer rates, due to vaporization of the object, the contribution of process iii) to the heat transfer can also be neglected. Finally, since the temperature profile is not affected by radiation, the latter need not be considered. The natural convection is brought about by gravitational body forces arising from a decrease in the

Jan 1, 1964

By R. V. Smith, E. J. Dewees, R. H. Williams

Before this paper was presented, the terms "f" and "v1/f in flow equations had been called "friction coefficient" and "friction factor," respectively. However, many authors have used the names for the terms interchangeably, with the result that considerable confusion has existed in the literature on flow of fluids. In an effort to establish a clear and concise terminology for these terms, the authors have designated f as "resistance coefficient" and dm as "transmission factor." Transmission factors for the flow strings of gas wells were determined by tests on wells in six fields of Oklahoma, Texas, and Louisiana. Data were collected on 14 gas wells while gas was flowing through 1 1/4, 2, 21/2, and 3-in. tubing and 51/2 and 7-in. casing. The transmission factors developed from these data were found to follow the resistance equation published by Nikuradse1 for turbulent flow in "rough" pipes with an average absolute roughness of 0.000,65 in. This average absolute roughness is believed to be representative generally of the flow strings of gas wells with the exception of those that have been exposed to corrosion or other conditions causing undue roughness. Also, use of an absolute roughness of 0.000,65 in. probably will result in transmission factors that are more representative of gas-well conditions than those in common use today, provided that the transmission factors are calculated by the methods outlined in this report. The authors believe that use of these transmission factors will permit calculation of more accurate subsurface pressures in gas wells than those in use today. Engineers use transmission factors in flow equations to compute subsurface pressures in flowing gas wells from measured wellhead pressures. These subsurface pressures are necessary for determining the productivity of gas wells from "back-pressure" tests. The methods of calculating pressures in flowing gas wells, as outlined by Rawlins and Schellhardt2 in Bureau of Mines Monograph 7, are based on the transmission factors in the well-known Weymouth formula" Natural gas engineers have realized that errors introduced by using transmission factors as given by the Weymouth formula are relatively unimportant in testing low-capacity gas wells; but they also know that such factors are important considerations in testing large-capacity wells. Accordingly, the research described in this report was undertaken to fulfill the need for more accurate means of calculating subsurface pressures in gas wells. This report is part of the Bureau's study of the flow of natural gas through pipe and commercial pipelines. Several of the conclusions regarding flow in the flow strings of gas wells were influenced by the results of the study of flow in horizontal pipelines. These instances are mentioned in the text of this report. METHODS OF COMPUTING TRANSMISSION FACTORS Methods and procedures for computing transmission factors for turbulent flow in circular pipes from test data taken on gas wells have been derived and explained in detail in a paper by Smith4. As these methods were used to calculate the transmission factors presented in this report, a summary is included. Starting with

Jan 1, 1955

By R. G. Hudson, H. W. Paxton

The activities of iron and chromium in their binary system have been measured by the Knudsen orifice technique. The system is close to ideal at 1200- 1250 C with slight positive deviations. The effect of this on the liquidus and solidus is discussed and these are calculated for two limiting assumptions. The vapor pressure of pure iron, pure chromium, and one alloy is compared with that obtained by the Langmuir free-evaporation technique. The results agree, indicating a vaporization coefficient close to 1. HERE are no reported data on the thermody-A namic activity of iron and chromium in the solid portions of the phase diagram. It is generally assumed'.' that the liquid solutions of iron and chromium obey Raoult's law. Chen and Chipman" have inferred that the liquid solution obeys Raoult's law. The minimum' in the solidus-liquidus curves for the iron-chromium system shows that there are deviations from ideality in either the solid or liquid or both. Because of the importance of developing reliable techniques for obtaining activity data in alloy systems at high temperatures and of the data so obtained, an investigation of the activity of iron and chromium in the binary at 1200-1250 C was undertaken using the Knudsen cell. Experimental The apparatus and experimental procedures used in this investigation were described in a previous paper." The various materials used for the construction of the Knudsen cell are listed in Table I. The metal used for the determination of the vapor pressure of chromium was 99.9 pet pure, obtained from A. D. Mackay, Inc. The iron was obtained as electrolytic grade from Fisher Scientific Company. The Fe-Cr alloys used are shown in Table 11. The largest error and controlling factor in the accuracy in the experiments reported here are introduced because of temperature uncertainty, which is estimated to be ±3 deg C. This introduces an uncertainty of 26 pet in the measured pressure. Experimental Results and Calculations The vapor pressures of pure iron and pure chromium were calculated from the measurements by the Knudsen equation3 on the assumption that only Cr or Fe atoms were present in the gas phase. For metal vapors, at the high temperatures and low pressures involved in these measurements this should be a reasonable assumption. Whitman" corrections for the cells were made. The data and results of pressure calculations are presented in Table I, and are plotted in Fig. 1. In addition the heat of vaporization at the absolute zero, ?E°°, has been calculated for chromium. These calculations are summarized in Table 111. The data used in these calculations are as follows kelley13 (F° - E°°/T ) Speiser, et al H (F° - E°°/T ) 010 where F" — standard free energy at temperature T It was necessary to calculate the total pressure above the alloys from the total weight loss W of the cell during a run, because of the fact that all attempts to collect and analyze the chromium and iron vapor effusing from the cell in the apparatus available failed. The failure resulted from the re-

Jan 1, 1959

By D. D. Pollock, D. I. Finch

PREVIOUS work' on a four-component system (Cu-Mn-Ni-Fe) resulted in the development of consistent relationships between the chemical composition and the electrical properties of these manganin-type alloys. The present study was undertaken to develop alloys with temperature coefficients of resistivity and thermoelectric properties more desirable than those of the manganin type, and to determine whether the relationships which had been found for the Cu-Mn-Ni-Fe alloys could be extended to five-and six-component alloy systems. PREPARATION OF ALLOYS The five- and six-component alloys were made from OFHC copper rod, ARMCO iron, electrolytic nickel, manganese cathode chip, and special high-purity aluminum and indium. A Cu-Mg master was used for deoxidation. The compositions of these materials are given in Table I. The alloys were melted and cast as indicated previously,' except that no cover was used and the melts were teemed. EXPERIMENTAL PROCEDURE The finished wire size of 0.0808 in. diam was again selected for the reason that the test specimens would be self-supporting, thus eliminating any extraneous effects which might have been introduced by winding smaller diameter wire on spools or forms. The following tests were performed on the finished wires: A) Chemical Analyses—All of the components of these alloys were determined by premium gravimetric methods. The principle residual impurity contained in these alloys is 0.008 pct Mg (by weight), maximum. Tables II and 111 present the mean analyses computed from at least four determinations of each constituent. B) Electrical Characteristics—The test procedures forthe determination of the thermal emf vs copper, resistivity, and the resistance-temperature relationship are given in detail in Ref. 1. It was also shown that the resistance-temperature relationship is of the form Pt = P,n + At -B/2, [1] where P, is the resistance at t C expressed in percent of a given standard resistance, P, is this per- 0 centage at 0°C, and A and B are constants for a given, properly treated, composition. The results of the electrical tests are also given in Tables II and 111. INTERPRETATION OF DATA The modified Linde2 formula, known to be valid for dilute binary solid solutions, was applied to the complex Cu-Mn-Ni-Fe type alloys. This relationship is of the form where Ap is the increase in resistivity. Zb the valence of the solute, Zn the valence of the solvent, and K and K are designations assigned by Robinson and Dorn3 to the constants for the periodic group to which solute element belongs. The units of K, are -cm per valence difference squared per at. pct; those of K2 are pa-cm per at. pct. For the sake of brevity, these units are not repeated in the following discussion. Calculations were made to determine if this formula was accurate for five-component systems. No experimental studies were made of the Cu-In and Cu-A1 binary systems. The effects of indium additions upon the resistivity of copper are given by Linde. These data, along with those of the effects of Mn and Fe, permitted the calculation of the effects of Al.

Jan 1, 1959

By M. E. Wadsworth, J. S. Cho

Colloidal silica dissolved in aqueous suspensions of high surface area thoria was permitted to adsorb on the thoria surface. Silica in three forms was identified by means of infrared spectroscopy and characterized by Si-O vibrational modes in the 9.0 to 10.5 region. A band at 9. 1 was attributed to free unad-sorbed silica, while adsorbed silica resulted in bands of greatest absorbency at 9.4 or 10.3p, depending upon the character of the surface bonding. Size considerations, the amount of silica adsorbed, and the character of the infrared spectrum for strongly adsorbed silica has been interpreted as evidence of formation of chain or layer silica linkages on the thoria surface. Infrared spectroscopy has been used successfully in recent years for the identification of minerals and synthetic inorganic substances. Unfortunately, infrared studies of silicate minerals have not proceeded to the point that unambiguous assignments may be made for Si-O vibrational modes as affected by lattice substitutions and structures. Several investigators have presented infrared spectra of silicate minerals, 1,7 and their work has pointed to the potential value of infrared to identify minerals as well as to note the sensitivity of various Si-O modes to structural and substitutional environments. The strong infrared absorption of various Si-O vibrational modes makes the infrared method a very useful tool for the study of silica adsorbed on the surface of solids of high surface area. Spaepen et a18 studied the adsorption of silica on thoria surfaces from aqueous solutions of silicic acid up to 300°C. A general review of the application of the infrared method to the study of surface adsorption has been presented by Pliskin and Eischens.9 EXPERIMENTAL Du Pont colloidal silica, Ludox SM (16.36% SiO2) and Ludox HS (30.25% SiO2) in aqueous suspensions were used as the sources of silica for the adsorption studies. The thoria used for this study was supplied by Union Carbide Nuclear Co.* under the preparation *Chemical Technology Div., Union Carbide Nuclear Co., Oak Ridge, Tenn. . number D-16-650. It was fired from the oxalate at 650°C and had a surface area of 32.4 ± 0.6 m2 per g measured by nitrogen adsorption. The chemical analysis of the D-16 thoria in ppm was: CO3= (5500), NO3- (< 4), so4±PO4 (100), and Si (20). The Ludox silica was placed in contact with the thoria in a two-liter autoclave10 between room temperature and 250°C. Slurries were made by placing 1 g of thoria in one liter of distilled water containing various additions of the silica sol. Samples were removed from the autoclave by opening a small stainless steel valve. Extracted samples were centrifuged for 10 min and excess solution was decanted. The sample was then dried for several hours at 80°C. Infrared samples were prepared by thoroughly mixing 10 mg of the thoria with 400 mg KBr in polystyrene vials on a "Wig-L-Bug" amalgamator. Pellets were pressed under vacuum and had final dimensions of 1.2 cm diam and 1.2 mm thick. Infrared spectra were

Jan 1, 1963

By Richard H. Jahns

Terminology and Basic Specifications Minerals and closely allied natural substances that are used for personal adornment, as raw stock for the fashioning of ornamental objects, or for other decorative purposes can be referred to collectively as gem materials. Industrial gem materials are those employed directly in various areas of industry. Substances that are manufactured for gem or industrial uses are termed synthetic gem materials; most of these correspond in composition and crystal structure to certain minerals found in nature. Imitation materials are those whose use is based upon their resemblance to substances of different composition and greater value. Gem stone is a designation commonly restricted to those materials suitable for personal adornment, and the complementary term ornamental stone is applied to the remaining materials not used industrially. This distinction is arbitrary and somewhat inconstant, owing to numerous geographic differences and historical shifts in end uses. Further, there is a complete gradation between the category of ornamental stones and that of dimension stone. Although many building and monumental stones are undeniably ornamental in their uses, treatment of such material is beyond the scope of this chapter. Substances that lose their identity in use are excluded from the gem category. Thus a transparent crystal of beryl would not be classed as a gem stone if it were treated as a source of beryllium metal. The adjectives precious and semiprecious have been employed as a means of distinguishing different gem materials on the basis of their recognized value. Diamond, emerald, ruby, and sapphire consistently have been regarded as precious stones, and in cut form they commonly are referred to as the noble gems. Opal, pearl, turquois, and chrysoberyl also have been classed as precious at various times. In recent years, however, it has been increasingly recognized that no satisfactory distinction can be based upon assessed value or any group of intrinsic properties, and at the present time all gem stones normally are referred to as precious. Indeed, the tendency is to extend this term to include many of the so-called ornamental stones, and the designation semiprecious has been essentially discontinued. Unlike most mineral commodities of economic value, gem materials are little altered in processing for end uses. Some stones are used in essentially their natural form, and most are reshaped and polished without significant changes in their fundamental properties. Thus the preparation of gem and ornamental stones is intended chiefly to emphasize or enhance desirable characteristics that are present initially. The worth of most synthetic gem stones is founded upon the identity between their major properties and the natural characteristics of the corresponding minerals, just as the pleasing qualities of imitation stones depend upon how well certain of their properties simulate those of more valuable substances. The most important specifications of gem materials represent four basic factors: beauty, durability, rarity, and portability. Beauty, whether expressed as splendor, "purity," attractiveness, or in some other way, is mainly a function of personal response to optical properties such as color, transparency, indices of refraction, and dispersion. Freedom from visible imperfections is important for transparent stones. For some substances beauty depends also upon asterism, opalescence, textural and

Jan 1, 1960

By H. H. Bein

Most western industrial sands are feldspathic and contain feldspars in variahle amounts. A few deposits will show alumina contents of less than one per cent while others will contain over twelve per cent alumina. Some industries are not especially concerned with the amount of contained feldspar but are interested only in color and in size gradations. Other industries, however, are very much interested in alumina content and set up quite rigid specifications as to this content. Several western plants are beneficiating crude sands both to reduce the iron content and to control the feldspar content. At present, most of these plants are using flotation processes for both controls although a few plants do use magnetic separators for the reduction of iron content. Some work has also been done with electrostatic separators for the feldspar-quartz splits. The Sand Division of Del Monte Properties Company, Pebble Beach, California, has been operating a flotation plant for iron removal and the separation of quartz and feldspar since 1950. As mentioned before, control of alumina, especially in the quartz product, is very important. Some users require an alumina content of less than two per cent and others will demand a product of less than one per cent Al2,O3,. The standard Quinolate method for determining alumina is lengthy and time consuming. The HF —H2SO4 evaporation step is especially critical and, if forced, spattering is apt to occur with a resulting loss of sample. Standard procedure is to evaporate to dry ness overnight at a low temperature. Even with forcing under optimum conditions the procerlnre will take two or three hours to complete. A new method has been developed which allows an alumina determination to be made, in 10 or 15 minutes, on a sample of the quartz product as it is being produced. This pocedure, although simply an approximation, has been most helpful in showing whether or not the product being formed is meeting specifications. This procedure has also allowed a great reduction in samples formerly taken and analysed by the orthodox method. Whether a sample assays 1.75% A12O3, or 1.95% .41,0, is not so important as the fact that it is below the allowable maximum of 2.00%. Similar thinking would apply to products required to contain less than 1.00% A1,0,. The step by step procedures for the method are as follows: 1. Collect sample, drain or filter, and dry. 2. Split sample through standard Jones sample cutter to quarter or eighth sample, depending on size of original sample taken, then split down to about 5 grams through Sepor micro-splitter. 3. Screen through 50 mesh sieve (U.S. Series) and reject undersize. 4. Weigh out 2 grams and place in platinum crucible. 5. Etch with 3-5 mls 38.40% HF for 1 minute at room temp. 6. Decant and wash. 7. Stain for two minutes in same crucible with a 1% water solution of Nigrosene dye. 8. Decant and wash well. 9. Dry.

Jan 1, 1961

By G. F. Bolling

STUDIES of grain boundary migration in zone-refined metals have all shown that the rate of migration is greatly reduced by small added solute concentrations. However, it is apparent that a difference exists between boundary migration during normal grain growth and single boundaries migrating in a bicrystal to consume a substructure. To effect the same reduction in velocity in the two cases, much more solute is required for grain growth than for the single boundary experiments. One case is available for direct comparison; both Bolling and winegardl and Aust and utter&apos; added silver and gold to zone-refined lead to study grain growth and single boundary migration, respectively. For comparable reductions in migration rates, about 500 times more solute was required to retard grain growth than to retard the single boundaries. A reason for this difference is suggested here. The rate of grain boundary migration is dependent on solute concentration and must therefore also depend on the solute distribution; i.e., regions of higher solute concentration encountered by a moving boundary must produce greater retardation and thus could determine any observed rate. A dislocation substructure can be the source of a nonuniform solute distribution since it can attract an excess concentration of certain solutes. In fact, it is probable that the solutes which impede grain boundary migration most would segregate most severely to a substructure for the same reasons. Thus a dislocation substructure present in a crystal being consumed could locally magnify the concentration of solute confronting an advancing grain boundary. In the single boundary experiments a low-angle substructure, within single crystals obtained by growth from the melt, was used to provide the driving force to move a grain boundary; in grain growth, no substructure of this magnitude was present. The increased solute concentration at subboundaries should be given approximately by C, = G e c,/kT, where t, is a binding energy and CO the bulk concentration. To account for the difference between the two experiments in the Pb-Ag and Pb-Au cases, C, must be the concentration impeding the single boundary migration, and a value of t, = 0.25 ev is necessary. This is reasonable, even though calculation on a purely elastic basis gives t, = 0.12 ev. because electronic effects must enter for silver and gold in lead. The compound AuPbz forms3 and the metastable compound AgrPb has been reported to nucleate at dislocations prior to the formation of the stable, silver-rich phase.4 Other observations support the hypothesis that a magnified solute concentration impedes the single boundary migration. For example, some crystals were grown by Aust and Rutter at concentrations of ~ 0.1 wt pct Sn and 2 x X at. pct Ag or Au which exhibited a cellular substructure, and in these crystals no boundary migration was observed. It is therefore evident that the higher concentrations at cell boundaries drastically inhibited migration. Inclusions would not have been responsible for this inhibition since according to recent work on cellular segregation,5 no second phase should have occurred in the segregated regions at the cell boundaries for the conditions of growth used, at least in the Pb-Sn system. In the purest lead, only the "special" boundaries observed by Aust and Rutter gave rise to the same activation energy as that obtained in grain growth. It is reasonable to suppose that the structure of special boundaries does not favor segregation at low concentrations and thus solute, or an inhomogeneity in its distribution, would have no effect. Random boundaries, on the other hand, are affected by solute and the substructure would enhance residual concentrations in the zone-refined lead, leading to a higher activation energy. It is clear, even without a detailed theory, that the apparent activation energies and exact solute dependence in the two experiments must be different as long as the non-uniform solute distribution produced by the substructure is important. Recrystallization experiments should also be susceptible to the same kind of local segregation at subboundaries or disloca tion cell walls; a suggestion similar to this has been made by Leslie et al.&apos; Following the arguments presented here, the effects of a given solute concentration would be like those observed by Aust and Rutter if segregation occurred, and like those of grain growth otherwise. This work was partially supported by the Air Force Office of Scientific Research; Contract AF-49(638)-1029.

Jan 1, 1962

By Owen F. Jensen

CONSTRUCTION of a ground-water supply includes many operations, which do not end with completion of facilities. Evaluations must be made of the quality of water in various areas and the history of production. Following an analysis of geologic, hydrologic, and chemical data there must be an exploratory drilling program and a study of resulting information. When the well is completed a continuous survey of operating records and basic data is necessary, since designs for future wells are varied as more data becomes available for those already completed. As the following discussion must be limited to a single undertaking, the customary procedure will be outlined for development and construction of a ground-water supply in which more than three wells are involved. Parts of this procedure are applicable for all ground-water supplies. Three possible sites were selected for construction of a paper mill. The problem was that the industry daily required approximately 15 million gallons of water of the best quality available; however, if water of the best quality were not available in the desired amount, water of a poorer quality could be used up to half the required amount, about 7 million gallons. In the preliminary survey approximately 1500 to 2000 square miles were covered for each site. Collected data consisted of several hundred electric logs of oil and gas wells; reports by the U. S. Geological Survey on ground-water resources of localities in and near the area; unpublished records of several hundred water wells including chemical analyses of the water produced and drillers&apos; logs of the wells; records of periodic water-level measurements made in observation wells by the USGS; topographic maps drawn up by USGS and by army engineers; and highway and county road maps. A preliminary report based on study and evaluation of these data was presented to the client, recommending the site with the most favorable and economical ground-water conditions. The study indicated that water of the quality and quantity desired could be developed. In this particular area there were indications that the aquifer could be separated into two zones con- taining water of different chemical character. This chemical character varied somewhat with area, but principally with depth, a factor which later proved an economic advantage in design of the well field. After studying the preliminary report, the client weighed other economic factors as well as ground-water advantages and selected a plant site. Authority was given to proceed with detailed study of the chosen area. Evaluation of preliminary data concerning the area indicated that it should be supplemented with additional information derived from actual exploratory drilling and testing. A flexible plan of exploratory drilling was devised so that data obtained as each test hole was drilled could be correlated with existing data and additional test holes could be located and drilled accordingly. Specific data to be obtained from each test hole were: samples of all formations penetrated; the driller&apos;s descriptive log of formations; electric logging surveys; one or more samples of water from selected water-bearing formations; temperature; and water levels and their recovery after periods of production. The area studied in such detail was approximately 400 square miles. Choice of location for the original test holes was based on the preliminary study. The pattern for these test holes was designed to require a minimum number of holes and to allow for interpolation of data between two, three, and four holes. Geologic, hydrologic, and chemical data gathered after completion of the first four test holes showed that the north section was the most desirable in the area, which was then reduced from the original 400 square miles to about 150 square miles for more detailed and intensive study. On the basis of findings from the current test a tentative well field was laid out and a drilling program devised. One test hole was located on the actual plant site and later developed into a small pilot production well equipped with a deep well turbine pump. Water from this well was used for general construction requirements. Another test hole drilled near the pilot production well and adjacent to the proposed route of the well-collection system was used during the pumping test of the pilot production well to determine the degree of interference. From the data thus obtained, calculations were made to determine the coefficients of transmissibility and storage. Three additional holes

Jan 1, 1955

By D. O. Hobson

Zirconium single crystals of various specific orientations were fabricated by rolling or drawing. The resulting textures were determined and are discussed with respect to the deformation modes that produced them. The crystals deformed in a predictable manner by combinations of up to third-order twinning with three twinning modes and by slip. Twinning was found to play a major role in initial texture formation. Texture changes produced by slip occurred only at the higher reductions. The twinning sequences that produced each intensity peak during the initial reductions could be identified. Schmid factor criteria were found useful in predicting which deformation modes to expect for each crystal orientation and fabrication procedure. The possible application of these data to poly-crystalline material is discussed. PREFERRED orientation or texture has a significant effect on the properties of most materials, causing anisotropy in fabricated cubic metals and enhancing the natural anisotropy of noncubic metals. This study evaluates the effects of several fabrication methods on the textures formed from specific starting orientations of zirconium single crystals and, it is hoped, gives an insight into the effects of the same operations on poly-crystalline material. BACKGROUND In fcc and bcc metals, texture changes take place by gradual lattice rotations caused by the operation of one or more slip systems. Deformation twinning plays an insignificant role in the deformation of such metals. In zirconium and its alloys, however, and in many other hep metals the ability to twin allows very rapid texture changes to be made with very small amounts of deformation. The deformation systems found in zirconium and its alloys are prism slip and three twinning modes.1 Slip occurs on the {1010}< 1120) system. There is little or no appreciable basal slip in zirconium. The twinning planes, illustrated in Fig. 1, are {1012}, {ll2l}, and {1122}. Two twinning modes, the {1012} and the {ll2l} operate for a tensile stress along the basal pole. A compressive stress parallel to the basal pole is required for {ll22} twinning. These twinning operations cause a 35- to 85-deg reorientation of the basal pole. The {1012} twin is the predominant tensile twin at room temperature. The twinning shears, S, are shown in the figure. A criterion for predicting which deformation system will operate when a grain is subjected to a known stress state is the Schmid (orientation) factor. This factor gives the fraction of the applied stress that computer program was written2 to calculate the Schmid factors for the four deformation modes in zirconium. It assumed three orthogonal stress axes and considered ninety-one different orientations of the basal pole in one octant of this stress space. At each basal pole position the Schmid factors were calculated for seven positions of rotation at 10-deg increments of the unit cell about the basal pole. Schmid factors were determined for a total of 637 orientations and for twenty-four deformation systems in each orientation. The program listed the Schmid factors for uniaxial stress parallel to each axis and, to approximate rolling, or-thonormal biaxial stress was also considered. Fig. 2 shows the range of orientations over which the various types of deformation would tend to predominate in biaxial plane strain with the stresses, equal magnitude. The exact boundary position between regions of different deformation modes depends, however, on the relative values of the critical shear stress for each deformation mode. Fig. 2 is drawn on the assumption that they are equal and it therefore may be only approximately correct. It is also recognized that the biaxial stress analysis may not be applicable in certain crystal orientations. EXPERIMENTAL PROCEDURE Single crystals of zone-refined zirconium, produced by Wilson of this Laboratory,3 were electrical-discharge-machined to form specimens for rolling, tube-drawing, and rod-drawing studies. Specimens were rolled at room temperature on 2-|--in.-diam hand-powered rolls from three different starting orientations: 1) the basal plane parallel to the rolling plane and the [1120] in the rolling direction, (0001)[ll20]; 2) the (1120) plane parallel to the rolling plane and the basal pole in the rolling direction, (1120)[0001]; and 3)_the (1120) plane parallel to the rolling plane and the [1100] in the rolling direction, (1120)[ll00]. Drawing specimens were cut with the [0001] direction as the drawing direction in the tube blank and [1120] as the drawing direction in the rod specimen. The drawing

Jan 1, 1969

By R. W. Ludt, C. C. DeWitt

The use of froth flotation for the separation of minerals has become one of the most important of ore dressing processes. Its particular adaptability to the enrichment of low grade ores has made the process an important factor in the national economy. The methods have been extended to the recovery of a great number of minerals. Among the few minerals which have resisted efforts toward industrial flotation is chrysocolla, a hydrated partly colloidal copper silicate. Chrysocolla, being a product of natural oxidation, has been found to occur in small quantities with many ores which are recovered by flotation methods. In present practice, these small quantities of copper silicate pass off with the tailings and are lost. The advantages to be gained by a satisfactory process for the recovery of chrysocolla is apparent. Any application of principles which points a way toward the satisfactory industrial flotation process for copper silicate would be of advantage. This paper presents an attack on this problem. Two methods for the recovery of chrysocolla have been developed by the United States Bureau of Mines.1,2 They have been successful on a laboratory scale but have been seriously restricted in industrial application by critical requirements in the procedure. In one of the Bureau of Mines methods,&apos; the ore is activated with sodium or hydrogen sulphide in an aqueous solution at a pH of 4. Amy1 xanthate is then used as a collector with pine oil as a frother in the flotation process. An excess of sulphide acts as a depressant and the state of optimum conditions is difficult to control industrially. In the second Bureau of Mines method,2 soap is used as the collector at a pH of between 8 and 9. The diffi- culties with this process are that soap is not a specific collector, that heavy metal or alkaline earth ions cause the formation of insoluble soaps, and that a more acid solution causes the formation of a free acid which does not act as a collector for chrysocolla. The problem of recovering chrysocolla by flotation involves the selection of a suitable collector. The collector molecule must be composed of an active polar group that has an attraction for chrysocolla, and of a hydrocarbon chain. Certain dyes have been shown to have an attraction for certain minerals. Suida3 found that hydrated silicates are colored by basic dyes. Dittler4 showed that chrysocolla, among other colloidal minerals of acid reaction, preferentially takes up such basic dyes as fuchsin B, methylene blue, and methyl green. Endell5 gave information to show that the colloidal material in clay may be determined by its selective adsorption of fuchsin. A simple experiment, likewise, illustrates the difference in the adsorptive power of chrysocolla and of silica for the basic triphenyl methane dyes. When a mixture of chrysocolla and silica is immersed in a very dilute dye solution, less than 5 ppm, the chryso-colla is rapidly dyed and the silica is dyed more slowly. The difference is substantial but one of degree. Dean2 showed that the dyes, crystal violet and toluidine blue, are taken up by quartz in an adsorption type process. The difference in the adsorptive power, however, offers the means by which a new collector may act. To form such a collector, a hydrocarbon chain must be attached to the dye molecule. This involves a process of organic synthesis. Butyl, hexyl, and octyl hydrocarbon chains were selected for substitution in the malachite green molecule. For the purpose of identification, the alkyl-substituted dyes formed are called: butyl-malachite green; hexyl- malachite green; and octyl-malachite green. An outline of the procedure for their synthesis is given in the appendix. It is generally recognized in the preparation of this type of dye that the chemical structure of some of the dye molecules varies. However, a uniform formula is attributed to the dye. Such a procedure has been followed in specifying the structure of these alkyl-substi-tuted malachite green dyes. The structure is given on the basis of their properties as an homologous series of dyes, on their method of preparation, and on the purity of intermediates used. Structure of substituted alkyl malachite green is: C6H4 N(CH3)2 p-R C6H4 CH C6H4 N(CH)2 Procedure The flotation cell is a Bureau of Mines 100-g, batch unit provided with an air inlet at the bottom above which is a variable speed agitator. The agi-

Jan 1, 1950

By I. L. Dillamore

I. L. Dillamore (University of Birmingham)—The different textures developed in various fcc metals have long awaited satisfactory explanation and it has now become clear that these differences are related to parallel differences in the deformation characteristics of the metals. Liu is correct, therefore, in seeking to account for the observed textures in terms of the flow mechanisms but I believe, for the reasons outlined below, that the particular interpretation of flow mechanisms proposed by Liu is open to substantial objections. By considering the forty-eight possible designations of the twelve octahedral slip systems found in fcc metals as distinct and separate deformation modes, Liu has fallen into the error of assuming that only positive glide dislocations associated with each system are present. In fact both positive and negative dislocations will be present and the only difference between for instance the systems B4 and B4&apos; (in Liu&apos;s notation) is that under a stress of given sign the direction of motion of a dislocation is reversed on changing from B4 to B4&apos;. For both orientations positive and negative dislocations will be present. In considering possible dislocation interactions it is, therefore, inadmissible to differentiate between R4 and R4&apos; as Liu does. Liu considers those dislocation interactions which give the biggest reduction in energy to be the most favorable and neglects, on the grounds that they will form strong barriers to slip, interactions between dislocations with perpendicular Burgers vectors. Setting aside interactions between positive and negative dislocations of the same slip system, which must occur regardless of the combination of slip systems chosen, the biggest reduction in energy occurs for the Lomer-Cottrell interaction and it is Lomer-Cottrell barriers which are thought to provide the stronger dislocation obstacles. On the other hand the intersection of dislocations with perpendicular Burgers vectors is thought to be a low-energy process which contributes only a fairly small temperature-dependent part of the total work hardening. On this basis it seems doubtful whether the reduction in energy through possible dislocation interactions provides a reasonable criterion for choosing the operative slip systems. From the point of view of texture development it is unsatisfactory to ignore the slip rotations leading to an end position and to neglect to consider the stability of the chosen end point. It is also unsatisfactory to treat the two stress axes as interchangeable since, if the stress system is idealized as biaxial, one stress is compressive and the other is tensile. For the same reason the rotations of the two stress axes are not made compatible simply by assuming that the same slip directions are responsible for the rotations of the two stress axes. It is, in short, essential to treat the two stress axes as acting together on the same slip systems. Turning to the question of the difference between the copper-type and the brass-type texture, there now remains little doubt that the difference is attributable to differences in stacking-fault energy (y), as noted by Liu, but it is doubtful whether the temperature dependence of the texture in copper and in silver is due to increasing stacking-fault energy with increasing temperature. The results of Swann and Nutting42 cited by Liu were obtained in Cu-A1 alloys and the apparent increase in stacking-fault energy on raising the temperature may be influenced by short-range ordering. In pure metals such effects are absent and the only data available on the variation of y with temperature are those of Buhler et a1.43 for silver. They report a minimum at 200°C which does not fit the hypothesis put forward by Liu. It is much more likely that thermal activation of cross slip is important in determining which texture develops, as proposed by Dillamore and tors. These workers have proposed an explanation for the differences in observed texture among the fcc metals and the pole figures predicted consist of an orientation spread which is in better agreement with observation than the limited number of discrete orientations suggested by Liu. The theory of Dillamore and Roberts is also able to account for the differences between aluminum and copper which Liu still leaves unexplained. Y. C. Liu (author&apos;s veply)—The writer appreciates the interest of Dr. Dillamore, but must discuss some of his comments in order to avoid cross purposes. The phrase, "forty-eight slip systems," which appeared twice in the text—in the caption of Fig. 1 and the first paragraph in the Discussion—might unfortunately have led Dr. Dillamore to disagree

Jan 1, 1965

By Robert L. Slobod

In much of the work reported in the literature on long cores. true connate water value, probably have not been obtained because of insufficient flow of 011 to attain equilibrium. A -.satisfactory method for establishing connate water in long cores has been developed in which oil flow is maintained until no additiona1 water is displaced. INTRODUCTION Long cores have been used by sev-erals investigators in an effort to evaluate the efficiency of oil recovery for various producing schemes. The effects of many variables such as rate of displacement. pressure drop, volume of displacing medium, gas-oil ratio, inter-facial tension, and others have been investigated, and the merits of gas drive have been compared with water drive. In the older experiments no connate water was used. but in the more recent stndies the philosophy of the experiment calls for a core containing oil and connate water (irreducible water) as the starting point of the experiment. The method generally used to establish this condition in long cores involves dynamic&apos; displacement wherein one or more phases are forced through the core. flow being maintained at a constant rate or at a constant pressure until a steady state is reached wherein there is no change of saturation with time. It is one purpose of this paper to point out that in much of the work reported in the literature true connate water values probably have not been obtained. The reason for this failure is pointed out. and a method for obtaining more reliable connate water values on long cores is presented. It is impossible at this time to completely evaluate the effect on the conclusions in the earlier papers resulting from the failure to obtain true connate water in the long cores, but some data are presented which indicate that serious errors may he present in many cases. MATERIALS AND APPARATUS Cores cut front outcrop sandstones (Strawn. Torpedo, and Elgin sandstones) with permeabilities of the order of 300 md were used. The major experiments were made with a core 18-in. long and 2-in. in diameter. Cores of the same diameter but only 12-in. long were used in a few tests? and in some work a core I-in. in diameter and 11-in. long was used. These materials were all somewhat bentonitic. &apos;To reduce the effect of such constituents, one of the cores (Torpedo No. 10) on which the most work was performed was acid extracted at the start of the experiment. Brine containing 50,000 ppm chloride and naphtha (Stoddard&apos;s Solvent) were used as the water and oil phases, respectively. The core was mounted in a rubber sleeve which forms the inner lining of a brass cylinder. In this arrangement2 the rubber sleeve is forced against the core by applying pressure to water in the annular space between the rubber sleeve and the brass cylinder wall. The core is therefore sealed in rubber so that all fluids introduced at the input end of the core flow through the core. With this equipment the core may be easily removed for inspection and analysis. Also, other cores may be introduced for study with no extra time for preparation such as is required when plastic mounting is used. When pressure or conductivity measurements are desired at intermediate points along tile length of the core, the brass cylinder comprising the outer jacket of the core holder is cut into section, of the desired length. Each section is then made up as an individual unit with its own rubber sleeve (see Fig. 1). The individual units are then butted up against a ring of plastic or other insulating material which carries an electrical contact for resistivity measurements and an opening which can be used for the measurements of fluid pressures. The individual units are forced tightly against the plastic ring separators and held in place with several tie rods. Inlet and outlet end butts of the same diameter as the core and several inches in length are provided to control the introduction and withdrawal of fluids and to complete the arrangement for sealing the core within the rubber sleeve. Fluid flow is maintained either by applying pressure to the liquid confined in a reservoir or by the use of a gear pump. The latter is preferable where continuous flow at a moderate rate over a long time interval is desired since a small volume of liquid can be readily recirculated using filters to prevent plugging of the core. EXPERIMENTAL The oven-dried core is weighed and is then completely saturated with brine

Jan 1, 1950

By J. E. Dorn, S. K. Mitra

The low -temperature tensile and creep behaviors of single crystals of copper were evaluated and analyzed in such a manner as to provide an estimate of the separate contributions of short-and long-range stress fields to strain-hardening. Furthermore, the average force-displacement diagram for thermally activated intep-section of two dislocations was estublished. This diagram plus a knowledge of the variation of dislocation spacing and the long-range back stresses with strain permits on accurate prediction of creep rates. The calculated activation energy for intersection under conditions of a constant strain rate increases linearly with the absolute tempevatus-e as required by theory. AN understanding of the detailed mechanisms for strain hardening constitutes one of the principal unsolved problems in dislocation theory. Two major models for strain hardening have been advanced in the past. The one that has received greatest attention assumes that strain hardening arises exclusively from long range interaction stresses between moving dislocations and piled-up arrays of blocked dislocations on the slip planes. This type of interaction was first announced by Taylor&apos; who revealed that the back stress fields due to a simple uniform array of positive and negative dislocations entrapped in the deformed crystal would result in parabolic hardening. Shortly thereafter Andrade and Henderson" demonstrated that the strain hardening of fcc single crystals was not parabolic, as previously thought, and finally it was recognized that a typical stress-strain curve consisted of three successive stages of deformation, niz., the easy glide, Stage I, linear hardening, Stage 11, and the parabolic hardening, Stage 111, ranges. The objections to Taylor&apos;s somewhat na&apos;ive model, which were presented so forcefully by cottrell; were largely removed by the more realistic details incorporated in Mott&apos;s analysis.5 But because Mott&apos;s theory for hardening via long range stress fields gave somewhat analogous results to that of Taylor&apos;s (inasmuch as it also predicted a parabolic rate of strain hardening whereas the observed rate of strain hardening in Stages I and I1 were linear), it was not widely accepted. Major consideration was therefore given to models, such as those which were advanced by Friedel and seegere that were formulated for the ad hoc purpose of yielding linear rates of strain hardening. The second major thought regarding strain hardening is based on the concept that it arises principally from short-range stress fields due to the interactions between intersecting dislocations. Cottrell and stokes7 showed, several years ago, that the constancy of the flow stress ratio at two temperatures regardless of the strain was inconsistent with the concept that strain hardening arose exclusively from long-range back stresses. The argument that strain hardening was primarily due to local interactions of intersecting dislocations was presented in considerable detail by asinski.&apos; Extending Basinski&apos;s method of analysis of the intersection process, Mitra, Os-borne, and dorn recently demonstrated that indeed the strain hardening in aluminum single crystals arises principally from local effects coincident with intersection; however, these conclusions, too, must be modified, as will be shown later in this report. The present investigation, devoted principally to the low-temperature deformation of copper single crystals, was initiated in an attempt to ascertain whether or not the same conclusions arrived at for aluminum also apply to metals, such as copper, which have much wider stacking faults. It was soon observed that the strain hardening in copper could not be attributed exclusively to local effects between intersecting dislocations. Previously no analytical method for arriving at the possible simultaneous contributions of long-range stress fields and localized forces on intersecting dislocations was available; consequently, the separation of these two factors could not be readily accomplished. In the present report a method of estimating the separate contributions of each of these two factors to strain-hardening will be presented. The authors will show that both long-range stress fields of the type contemplated by Seeger and Friedel as well as short-range forces of the type considered by Basinski are responsible for strain hardening in fcc metals at low temperatures. This method of analysis also accounts for, in a satisfactory way, the effect of stress, temperature, and strain on the creep rate under constant stress. Furthermore, in the course of presenting their methods of analysis the authors will also reveal the rather complete agreement of their experimental data with the concepts of the theory for thermally activated intersection of dislocations. INTERSECTION MODEL As shown by seegerl0 the strain rate arising from thermally activated intersection of dislocations is given by

Jan 1, 1962

By H. N. Hall

Various factors must be considered in an engineering evaluation of gravity-drainage reservoirs. Among these are: (1) the effect of producing rate on total oil recovery; (2) the effect upon well productivity and ultimate recovery of the pressure level maintained during the producing life of the reservoir; (3) the economic advantage of full or partial pressure maintenance; and (4) estimate of the rate of gas production and injection and the possible purchase of gas under conditions of full pressure maintenance to ascertain compressor facilities needed. All of these factors can be evaluated only when a reliable method is employed for determining reservoir performance in gravity-drainage reservoirs. The purpose of this paper is to present a general method for calculating the performance of a gravity-drainage reservoir. This method is applicable for conditions of complete pressure maintenance, partial pressure maintenance and normal pressure depletion. Provisions are made to take into account variations throughout the reservoir of reservoir configuration, changes in permeability and fluid composition. Based on the method presented in this paper, an IBM 650 computer program has been developed. The past performance of an actual gravity-drainage reservoir producing under conditions of declining pressure and no gas injection was duplicated using this program. INTRODUCTION In tilted reservoirs the production of oil is influenced by drainage of oil from upstructure to downstructure locations. When this downstructure drainage of oil is sufficient to cause effective segregation of the gas and oil in a reservoir, the reservoir is usually classified as a segregation drive or gravity-drainage reservoir. (Discussion will be restricted to gravity-drainage reservoirs which have no encroachment of edge water.) The important feature in gravity-drainage reservoirs is the density difference between reservoir oil and gas. These phases tend to segregate in the reservoir with the result that in the gas cap the oil saturation is maintained at a higher level by drainage of oil from the gas-cap area. Oil can be produced from the oil zone at a low gas-oil ratio and reservoir energy is thereby conserved. The standard material balance in not adequate for predicting gravity-dramage reservoir performance because it does not take into account the difference in saturation above and below the gas-oil contact. Several authors&apos;.&apos; have presented methods for calculating the performance of gravity-drainage reservoirs in which reservoir pressure is maintained constant by gas injection into the gas cap. Using some simplifying assumptions, these methods can be employed with a desk calculator to give acceptable results. The problem of predicting the performance of gravity-drainage reservoirs under the conditions of declining reservoir pressure is many time more complex than that of constant pressure. fierefore, attempis to develop a method suitable for desk calculation have required excessively simplified assumptions. In the past several years, highspeed digital computers have become more widely available for reservoir engineering problems. These corn puters are well suited to problems such as the prediction of the performance of gravity-drainage reservoirs with pressure decline. Many of the simplifying assumptions necessary for hand computation can be eliminated so that a realistic approach to the gravity-drainage process can be made. CONCEPTUAL PICTURE OF OIL MOVEMENT IN GRAVITY-DRAINAGE RESERVOIRS Before attempting to develop an analytical treatment for conditions occuring in a gravity-drainage reservoir, a concept should be formed concerning the movement of fluids in the reservoir as oil is produced. A review of the literature&apos;.&apos; shows that it is customary to classify gravity-drainage operations into two categories—(1) with complete pressure maintenance, and (2) with declining pressure. The same line of reasoning will be followed in presenting the concept of the movement of fluids in the reservoir because it is easier to visualize the movement of fluids under conditions of complete pressure maintenance. After discussing complete pressure maintenance, an analogy will be made between that and the case of declining pressure. It should be kept in mind throughout that the final aim for the problem of solving gravity-drainage performance with digital computers will be to develop a general program for any kind of gravity-drainage reservoir. COMPLETE PRESSURE MAINTENANCE One feature which is generally common in gravity-drainage reservoirs is a gas cap located at the top of the structure. This is shown in Fig. 1(a). Fig. l(b) shows oil saturations that might occur through the reservoir. In the gas cap, oil saturation is lower than