Search Documents

By N. Arbiter, C. C. Harris

In 1961, a research program started at Columbia into the mechanical aspects of flotation,* and certain ends are now in view. The purpose of this note is to explain these tentative conclusions in the hope of stimulating discussion and eliciting new data, especially industrial data, with which to test the views expressed. The variables presently under consideration are impeller rotational speed, N, volumetric air rate, Q, and impeller diameter, D, the latter being the parameter chosen to designate cell size. The most favorable *The latest work 1 references all previous publications. chemical environment is not under discussion since the procedures for establishing it are better understood than those for optimizing N and Q by virtue of a longer history of more intensive investigation. THE GRADE AND RECOVERY SURFACES With a given ore, chemical treatment, and flotation machine, both grade, G, and recovery, R, are functions of N and Q. The GNQ and RNQ relationships are best viewed in terms of three-dimensional surfaces (Fig. 1) which are experimentally determinate.2 TO maintain grade at an acceptably high level, it is necessary for N and Q to lie within certain limits, and similarly with recovery. However, the ranges of N and Q for grade on the one hand and recovery on the other are rarely the same. Selecting the single N

Jan 1, 1970

By William A. Kennedy, Jonathan R. Stahl

This paper deals with the phenomenon of water held in a leach dump due to capillarity. Water is shown to be retained in the fine pores of the ore as well as in the interstices between the rock and soil particles. Upon drainage, Chino leach dump material shows two distinct capillary systems and a double capillary curve is often obtained. Both the igneous and the sedimentary rocks composing the leach material are shown to have appreciable porosity but little permeability. Fluid flow is, therefore, restricted to the interstices between the rock and soil particles. The irreducible water saturation for the aggregate is found to be 884 for the -48 mesh material and 235 for the448 mesh to one inch material. The composite sample of minus one inch dump material had an irreducible water saturation of 52 percent. The irreducible water saturation in the fine pores of the ore was found to be between 73 and 76 percent. Very coarse pores or channels between large rocks exhibit essentially zero capillary retained water. The presence of fine material in a dump can cause high water saturations to be retained and these saturations may be mistaken for perched water tables. Perched water tables can be drained but capillary water will be retained. Capillary pressure data can aid in distinguishing between perched water tables and capillary retained water.

Jan 1, 1974

By Blamey Stevens

The object of this paper is to show how igneous intrusion is governed by definite mechanical laws. A distinction is made between dikes and fissures, and the various characteristics of intrusions are explained on an exact scientific basis. The modification of rock-stresses by intrusion is then considered and extensive isostress regions are recognized. Finally, a complete classification of intrusions is constructed covering all possible cases. The generalizations of observed data, taken from Geikie's Text-Book of Geology, confornl to the laws of intrusion herein stated, and the deductions based upon these lams. No authority, however, is quoted for the type which I hare named a corrugated intrusion. Its existence is a necessary deduction from the laws of intrusion, and even the entire absence of examples in technical publications cannot disprove its reality. In all probability, corrugated fissures would have remained undiscovered, but for the nrorking of mineral veins. As intrusions of tabular form are seldom worked for commercial purposes, it has been left for theory to anticipate the discovery of corrugated dikes. In the light of these laws of intrusion and the corresponding laws of fissures,' there seems to be a remarkable uniformity of stress-distribution in rocks at moderate depths. This renders possible the mathematical calculation which should help us to approximate exact science in this and kindred branches of applied geology.

Jan 1, 1911

By C. R. Woodcock, J. S. Mason

In almost any situation where particulate or granular bulk solids have to be conveyed, whether for a distance of a few metres or for many hundreds of metres, a pneumatic conveying system may be considered. Conveying by pipeline is convenient and clean, but running costs may be substantial because of the heavy air consumption and the trend has therefore been towards dense-phase transport in which the ratio of conveyed solids to conveying air is kept high. This paper concentrates on air-float conveying, which can be regarded as an extreme form of dense-phase conveying where the bulk solid is fluidised in a channel and then caused to flow, either by inclining the channel or creating a pressure gradient along 'it. Various designs of air-float conveyor for upward, horizontal and down- ward transport of powders are discussed, with special emphasis on the latter case. In situations where a continuous downward slope can be provided, the combination of air-fluidisation and gravity flow results in a conveying system that, for many kinds of bulk particulate solid, would be hard to better in terms of convenience, reliability and economy. The paper is concluded with a discussion of design features and performance of practical air-gravity conveyors, involving the handling of various bulk particulate solids, both in research and in full-scale industria1 applications.

Jan 1, 1980

By P. C. Kapur

An approximate but simple and practical solution to the discretized batch grinding equation has been obtained. The solution is based on a new grind function, a combination of selection and breakage parameters and particle-size distribution of the feed. The grind function, which is readily computed from limited experimental data, has significant implications for analysis of the particle-size reduction processes. Using the practical solution, three ball-mill comminution systems—dry dolomite, wet quartz, and limestone—have been simulated with acceptable precision. The application of the discretized batch-grinding equation1 to routine comminution analysis is frustrated by two principal difficulties. First, the selection and breakage parameters of the grinding equation must be computed separately. This is usually a difficult and uncertain task although, recently, a number of experimentally and computationally efficient strategies have been proposed for determination of these parameters?" Second, for actual computation, the solution to the batch-grinding equation becomes progressively tedious and unwieldly for finer particle-size range.1,2 The purpose of this part of the report is to present an approximate solution to the batch-grinding equation, which is practical in that it seems to overcome the aforementioned obstacles. The solution involves the concepts of a new grind function, a lumped parameter of the selection-breakage functions, and particle-size distribution of the feed, which is readily computed from a limited amount of experimental data.

Jan 1, 1971

By L. C. Weiner

For zinc single crystals, xo = 3o, a surface coating raises both the cleavage and yield strengths over a large temperature range. The "brittle temperature," associated with slip after completion of twinning, does not coincide with the point of intersection of the flow and cleavage curves, which is associated with twinning. A surface film has no effect on the brittle temperature, while it lowers the intersection temperature some 20°. For crystals, yn = 83o, a coating decreases the cleavage strength, making it temperature independent, as well as increases the brittle temperature or its equivalent, the intersection temperature, 20°. These observations are described on the basis of a dislocation-pile-up-at-a-barrier model for brittle fracture; in crystals x,, = 3o the number and distribution of twins play a vital role. IN a recent investigation on the effects of solid environments on the brittle fracture of zinc single crystals,' it was demonstrated that the presence of a surface film changes the cleavage strength of these crystals, either increasing or decreasing it, depending on the crystal orientation. An increase in cleavage strength of some 43 per cent was found for coated crystals oriented x, — 3o K = 28",* while a decrease of 48 per cent was observed with crystals X" = y» — 83". Moreover, these effects were found

Jan 1, 1959

By Dermot M. Ross-Brown

Introduction Slope angles are one of the major factors affecting the shape of the final pit and the location of the walls Due to differences in geology, the optimum slope angles vary from pit to pit and within different parts of the same pit. Indeed, it is not unusual to have different slope angles for the top and bottom portions of the same cross section. The optimization of these slope angles is a major study in itself and this chapter is intended as a general introduction to the subject. It is not intended to be a comprehensive text for the absolute beginner The objective is to put the various aspects of slope stability analysis into relative perspective by describing the vari¬ous analytical techniques available and indicating when each may be most appropriately used References are made to the many excellent texts and papers on slope stability for the reader who does not have a formal training in soil or rock mechanics. In writing this chapter, an assumption has been made that a tentative mining plan has been drawn up, includ¬ing a preliminary estimate of the slope angles. It has also been assumed that all the necessary field and laboratory data has been collected and reduced to a form suitable for input into the stability analyses.

Jan 1, 1979

By A. E. Gorum, J. Washburn, E. R. Parker

Experimental evidence was obtained in support of the idea that cleavage fracture can be initiated by dislocation pile-up. The high ductility of MgO crystals when tested in bending comPared to their relative brittleness in tension was explained on the basis that large pile-ups are more likely in a tension specimen. CLEAVAGE fractures have been a problem of major concern for many years. A number of large steel structures have failed in a brittle manner, usually suddenly and without warning; often the failures occurred for no obvious reason and at nominal stress levels well within the generally accepted range. A great deal of data have been collected about factors that contribute to failures,1 but the physics of the fracture process has never been revealed. cottrel12 has recently developed a theory of brittle fracture in ductile materials which was based upon the concept that dislocations moving on two intersecting planes can unite to form a crack nucleus. This theory accounts for the known effect of grain size and for the effect of testing temperature. There has, as yet, been no experimental evidence published that would substantiate this or the earlier theories based on stress concentrations due to piled-up dislocations. The study reported herein was conducted to obtain information that would either substantiate or disprove the

Jan 1, 1960

By G. C. Hancock

The operating plant of The Broken Hill Associated Smelters Pty. Ltd. is situated at Port Pirie in South Australia and it treats to finality the whole output of lead concentrates from the mines of The Zinc Corporation Ltd., North Broken Hill Ltd., and aroken Hill South Ltd. at Broken Hill, New South Wales. Lead bearing ores from other sources are also purchased for treatment and lead scrap and residues are treated on a toll charge basis. The present output of the plant is approximately 200000 tonnes of refined lead per annum and there is a substantial production of by-products including refined silver, gold, cadmium, antimonial lead alloys, copper matte and sulphuric acid. Recently the Company commenced the production of zinc by slag fuming and electrolysis from a six million ton dump of lead blast furnace slag, which has been accumulating at Port Pirie for over fifty years. The slag fuming plant contains two furnaces of conventional design, but features a high degree of pre-heat for the blast air and this is obtained by the use of all-metal recuperators. The raw zinc oxide fume produced by the plant is roasted in a rotary kiln prior to treatment in the leaching and electrolysis sections, which follow conventional practice for nigh current density plants. Present output is approximately 36000 tonnes of electrolytic zinc per annum.

Jan 1, 1970

By J. M. Pilcher

The application of oil to coal for-the reduction of dust has greatly increased the consumers' satisfaction with solid fuels, especially those for domestic use. The combination of oil-treated coal and automatic firing by a small stoker has made possible clean, automatic heating with bituminous coal. This, with the added pressure of competition by other fuels, has caused a rapid development of oil treating practice. A variety of materials derived" from petroleum oils is available from which one may choose for treating a par-ticular coal. Until recently, however, little information had been published to guide the choice. It is most im-portant that the proper type and amount of oil be used in order that all coals marketed as "dustless" will be reason-ably dustless, and thereby maintain a good reputation for oil-treatment. During the past two and one-half years, an investigation of a number of the problems related to the treatment of coal with oil has been conducted at Battelle Memorial Institute. This project was jointly sponsored by Bituminous Coal Research. Inc., Standard Oil Company of New Jersey, Sun Oil Company, and Viking Manufacturing Company. A progress report giving the principal results of the work of the first year was presented before the American Society of Mechanical Engineers in December 1937.1 The present paper is a summary of the entire inves-tigation.

Jan 1, 1939

By Willard H. Mutchler, Henry S. Rawdon

As part of the study of the scratch-hardness method for metals and alloys in coöperation with one of the technical committees of the American Society for Testing Materials, the authors devoted considerable time to the study of the changes in hardness of metals when cold rolled. Various seemingly contradictory statements in the technical literature concerning the applicability of the serateh-hardness method to such cold-rolled materials were among the principal reasons for the investigation, the results of which are in part presented here. The effect of cold deformation, at least in moderate degrees, on the hardness as measured by the Brinell aid other common methods is so well known that further reference is unnecessary. Concerning the scratch hardness of cold-worked metals, Martens and Heyn state1 that hardness, whether measured by the ball-pressure rnethod (Kugeldruck) or by the scratch method (Ritzverfahren), will be increased by cold deformation. Jeffries and Archer give a seemingly diametrically opposite view. They state,2 that "the sclerometer (indicating scratch hardness) shows little difference between cold-worked and annealed metals." Portevin3 has shown that the rate at which the Brinell hardness of cold-worked copper and brass increases is very high for relatively slight deformation after which it drops to zero, while Merica and Walten-berg4 have observed that monel metal shows evidence of softening on

Jan 1, 1924

By G. W. Brock

Experiments in the form of aging of overstrained tension specimens and elevated temperature tension testing, have been carried out on recrystallized arc-cast molybdenum. The aging behavior of molybdenum was found to be strongly dependent on the degree of plastic strain present in the lattice: the reason for this being the low solid solubility for the common interstitial elements in molybdenum. GEORGE W. BROCK, formerly Research Associate, Department of Theoretical and Applied Mechanics, University of Illinois, Urbana, III., is Research Associate, Department of Engineering Sciences, IBM Research Center, Yorktown Heights, N. Y. Manuscript submitted January 19, 1961. IMD THE term strain aging is familiar in connection with the recovery of the yield point in mild steel after tensile overstraining, and there are other instances where it is known to exert an appreciable effect on mechanical properties. For example, steel exhibits a greater tensile strength at mildly elevated temperatures than at room temperature and serrated stress-strain flow curves occur under certain conditions. It has been known for a number of years that the phenomenon of strain aging is directly connected with the presence of carbon and nitrogen in the lattice; and extremely small amounts of either element are sufficient to produce the effect. In this study, the aging behavior of overstrained tensile specimens of recrystallized molybdenum has

Jan 1, 1962

By Neil H. Bostick

A specialized electronic data system processes data taken from normal gologic maps and stratigraphic tables to yield predictions of uranium resource location for an area such as much of the United States. Strata underlying specific quadrangle cells of the earth are evaluated for uranium favorability on the basis of selected criteria of lithology, structure, and stratigraphy but not specific past production in the area. Stored data are computer processed to yield volume of likely host rock beneath each cell to a given depth and at a given favorobility level. Results are plotted by machine directly as maps. A specialized and simplified procedure for predicting approximate uranium resources has been devised at Stanford Research Institute (SRI). The prediction is based on general geology beneath specific area cells of the earth in order to provide complete volume coverage; the strata underlying these areas are evaluated for uranium mineral favorability on the basis of a few selected geologic criteria in order to allow rapid data input. In order that the predictions be generally applicable, they are based on geological factors only, not past ore production of a given cell. Since the bulk of U.S. resources are in elastic host rocks, only such strata are considered in this work. This paper describes the structure and some details of the resource system and how it was tested in an area of the western United States.

Jan 1, 1971

By T. D. McKinley

Theory, operational characteristics, and indicated precision and accuracy of analytical methods based on vacuum extraction, equilibrium pressure, and combustion approaches are reviewed. At the present time vacuum extraction at 1400°C and the equilibrium pressure method are recommended for determination of hydrogen in titanium and titanium-rich alloys. UNTIL a few years ago the role of hydrogen in titanium was an unknown factor with regard to its effect on the physical and mechanical properties of the metal. However, following the work of Jaffee and othersa-" it is now generally acknowledged that hydrogen has a degrading effect on titanium and its alloys. The chief manifestations are a decrease in impact strength in -systems and delayed cracking in a-ß systems. Since hydrogen does have a de- grading effect on titanium it is essential to control it within tolerable limits. It then follows that procedures for quantitative estimation of hydrogen are a primary requirement for the industry. For greatest benefit these methods should be simple, rapid, and precise. In addition to having these virtues, methods must be easy to duplicate in both equipment and technique to gain widespread use. After inherent accuracy has been established, the, required precision to make a method acceptable is dependent largely on the nature of the work at hand. Ability to obtain a representative sample has a pro-

Jan 1, 1959

By George Stern

THE purpose of this investigation has been to study one method for making ordinary carbon steel by the powder metallurgy technique. This method con- [ ] sists of pressing and subsequently sintering an intimate mixture of iron powder and graphite in a suitable atmosphere to produce a steel. Two types of iron powder have been studied, electrolytic and reduced. The sintering of mixtures of loose carbonyl iron and carbon black for several hours at 1000° to 1100°C. (1830° to 2010°F.), followed by forging of the resultant ingots to bars, has been studied by Offermann.1 Trail' has reported on the properties of hydrogen-reduced and electrolytic iron powders, both containing 0.5 per cent carbon. Methods for making steel bodies by powder metallurgy have also been sug- [ ] gested by Goetzel,3 who recommends the addition of steel powder of well-defined carbon content to pure iron powder, and Volterra,4 who suggests compaction and subsequent sintering of a mixture of steel powder, iron oxide and iron powder. Additional methods for making steel bodies by powder metallurgy have been reported in the literature by Koehring,5 Allen,6 Balke,7 Wulff,8 Boegehold,9 and others. 10,11,12 It is felt that the method of pressing iron powder and graphite, as described herein, lends itself best to production because of the lubricating action of the

Jan 1, 1946

By George Stern

The purpose of this investigation has been to study one method for making ordinary carbon steel by the powder metallurgy technique. This method con- sists of pressing and subsequently sintering an intimate mixture of iron powder and gaphite in a suitable atmosphere to Produce a steel. Two types of iron Powder have been studied, electrolytic and reduced. The sinkring of mixtures of loose Car-bonyf iron and carbon black for several hours at I000 to 1100 C. (1830' to 2010°F.), followed by forging of the resultant ingots to bars, has been studied by Offermann.' TrailZ has reported on the properties of hydrogen-reduced and electrolytic iron powders, both containing 0.5 per cent carbon. Methods for making steel bodies by powder metallurgy have also been sug- gested by Goetzel13 who recommends the addition of steel powder of well-defined carbon content to pure iron powder, and Volterra,~ who suggests compaction and subsequent sintering of a mixture of steel powder, iron oxide and iron powder. Additional methods for making steel bodies by powder metallurgy have been reported in the literature by Kohering Allen,6 Balke,7 Wulff,8 Boegehold,9 and others.,0,11,12 It is felt that the method of pressing iron powder and graphite, as described herein, lends itself best to production be-Cause of the lubricating action of the

Jan 1, 1946

By George Stern

The purpose of this investigation has been to study one method for making ordinary carbon steel by the powder metallurgy technique. This method con- sists of pressing and subsequently sintering an intimate mixture of iron powder and gaphite in a suitable atmosphere to Produce a steel. Two types of iron Powder have been studied, electrolytic and reduced. The sinkring of mixtures of loose Car-bonyf iron and carbon black for several hours at I000 to 1100 C. (1830' to 2010°F.), followed by forging of the resultant ingots to bars, has been studied by Offermann.' TrailZ has reported on the properties of hydrogen-reduced and electrolytic iron powders, both containing 0.5 per cent carbon. Methods for making steel bodies by powder metallurgy have also been sug- gested by Goetzel13 who recommends the addition of steel powder of well-defined carbon content to pure iron powder, and Volterra,~ who suggests compaction and subsequent sintering of a mixture of steel powder, iron oxide and iron powder. Additional methods for making steel bodies by powder metallurgy have been reported in the literature by Kohering Allen,6 Balke,7 Wulff,8 Boegehold,9 and others.,0,11,12 It is felt that the method of pressing iron powder and graphite, as described herein, lends itself best to production be-Cause of the lubricating action of the

Jan 1, 1946

By S. L. Hoyt

IN technological studies on steel considerable emphasis has been placed on the identification of the foreign inclusions, testimony of which is adequately given in the metallographic literature covering methods for their identification. The outstanding accomplishment in this field is the scheme devised by Campbell, Comstock and Wohrman for identi-fying various oxides, sulfides, silicates and other constituents by syste-matic etching tests and microscopic examination.1 The time involved in carrying out this procedure has led to attempts to secure quicker methods, or at least to shorten the time required to secure essential information. An example of this is the use of dark field illumination, but when this was tried out by the authors it was found that cavities and pits on the polished surface appeared bright on a dark field and could not be distinguished from small glassy inclusions. Still another means is the Leitz Ultropak, an instrument equipped with optical units for the illumination of the specimen by reflected light to secure an effect similar to dark field illumination. The structures are made visible in exceedingly sharp details by utilizing the inherent properties of the samples, such as refractive index, absorption coefficients and reflection powers. We have had no experience, with the Ultropak, but a recent paper by Benedicks and Löfquist3 describes methods for

Jan 1, 1934

By Eric Kula, Åke Josefsson

L. J. Dijkstra and R. Sladek, (Ontario Research Foundation, Toronto, and Institute for the Study of Metals, Chicago, respectively)—This interesting paper confirms some results obtained some years ago in collaboration with Fast: namely the broadening of the nitrogen peak by the presence of small amounts of manganese. Later on a more extensive study of this effect was made at the Institute for the Study of Metals at Chicago. As the work has not yet been submitted for publication we wish to mention here briefly some of the results. The effect of about 0.5 atomic pct manganese, chromium, molybdenum, or vanadium on the nitrogen-peak in iron was examined. The broadening found previously in the case of manganese was even found to be more pronounced for chromium. In the case of molybdenum and vanadium a double peak was observed which seemed to justify the idea that in all cases mainly two relaxation times were involved: namely, the normal relaxation time as found in pure iron and a second relaxation time related to the existence of abnormal interstitial lattice sites introduced by the foreign metallic element. The analysis showed that for the normal nitrogen-peak as a reference at 22°C the abnormal peak was found at about 32°, 47°, 75°, and 87°C in the case of manganese, chromium, molybdenum, and vanadium, respestively. In the manganese alloy the free energy difference for a nitrogen-atom at an abnormal and a normal lattice site was estimated at 2800 cal per mol. This means that for temperatures above 100°C the solid solubility and overall diffusion rate of nitrogen is not much affected by additions of 0.5 pct Mn. We believe that the difference in rate of precipitation of nitrogen in pure iron and the manganese alloy is mainly a question of the number of potential nuclei available in the different steels. In studying the effect of these alloying elements on precipitation of nitrogen, a distinction must be made between the para reaction and ortho reaction, using terminology introduced by Hultgren.7 The ortho reaction in which the alloying metallic element participates in the diffusion under formation of nitrides occurs at high temperatures such as 600°C. The para reaction in which the alloying metallic element does not diffuse and in which the nitride inherits its alloy content from the matrix occurs at lower temperatures. To prevent the ortho reaction the alloys have to be quenched rapidly from the phase. It is not surprising that the authors find that the height of the peak indicates a lower nitrogen content than chemical analysis. In the first place the peak is not a single relaxation peak and secondly, the steels were not quenched from the phase after the nitrogen was introduced at 580 °C.

Jan 1, 1953

Discussion of the paper of K. Huessener, (Trans., vol. 53, pp. 402 to 4333, and of the papers of Linn Bradley, H. D. EGbert and W. W. Strong, pp. 303, 319. R. J. WysoR, So. Bethlehem, Pa. (communication to the Secretary*). —At our plant (Bethlehem Steel Co.), we have had several Bradshaw burners under course of construction and erection for some time, but up to the present we have not had opportunity to put them in service. I regret that I can not take part in the discussion with some actual results from these burners. Mr. Huessener properly emphasizes the importance of obtaining the highest combustion temperature practicable in boiler practice, which demands a near approach to perfect combustion conditions. The ideal burner is the one which, while meeting the various mechanical requirements, fulfills the above condition under a wide range of gas pressure. The question as to the relative value of hot raw gas and cold washed gas for boiler use is a very interesting one. I think that in the past the importance of low temperature of washed gas sometimes has been overemphasized. Mr. Huessener has pointed out that so far as temperature is concerned, no advantage accrues in washing gas below 100" F. In many plants, there is a notable operating economy in using furnace cooling water, which is appreciably warmer than the supply water. However, in a given type of washer, other conditions being constant, the lower the exit gas temperature the lower will be the dust content; this is equivalent to saying that the more washing water is used, other conditions being constant, the lower will be the dust content of the exit gas. For each type of washer there is a certain desired average temperature difference between inlet water and exit gas, concomitant with known average dust and moisture contents, and with economical operation. With the present tendency toward smaller stove checkers, it is generally agreed that gas for stove use should be cleaned to a dust content of 0.20 grain or less. The method employed and extent of gas cleaning are clearly problems for individual furnace plants. As a general proposition, wet washing is decidedly more attractive for furnaces smelting soft, fine Lake ores than for those reducing chiefly hard, lumpy ores, such as the foreign and domestic magnetites. In the former case the average moisture content of the gas is probably 35 grains per cubic foot, the dust content is relatively high and the top temperature relatively low. In our plant, the ore mixtures consist almost exclusively of hard magnetites. The average dust content of the gas leaving the dust catcher will average only about 2 grains and the moisture about 12 grains per cubic foot, corresponding to saturation at about 83" F. The temperature is fully 100" F. higher

Jan 1, 1917