Search Documents

By Ionel I. Gardescu

During the summer of 1930 the average daily oil production of Rumania registered a new peak at 128,000 bbl. per day. The estimated potential production as of September, 1930, was as high as 235,000 bbl. per day. During the latter part of the year, by mutual agreement, the operators decided to curtail their output to about 100,000 bbl., which brought the average for the year to 116,600 bbl. The total production for 1930 was 41,572,000 bbl. (last month estimated) as compared with 35,757,000 bbl. for 1929, or an increase of 16.3 per cent. over last year's production. The production for the last 10 years is given in Table 1. The curtailment of production was prorated per company, based on its total estimated potential production as of September, 1930, and not per field. As a consequence, at present there is little development of protected or slightly productive areas; viz., Arbanasi, with an average production of 1750 bbl. per day, dropped to less than one-third after curtailment came into effect. Moreni, with an average production of 92,000 bbl. per day, while producing 58 per cent. of the country's total output in 1929, went to 67 per cent. at the beginning of 1930 and to 75.2 per cent, towards the end of the year. The modified Mining Law of 1929 is still in effect. This law withdraws the restrictions set on foreign capital by the law of 1924. As a consequence a large percentage of proven state land was alloted through competitive bidding to foreign companies. The Romano-Americana (Standard of New Jersey) acquired several leases in the Boldesti and

Jan 1, 1931

By C. H. Noren

For some years the Du Pont Company has utilized computer calculations to study the various theoretical properties of explosives. These studies have yielded valuable information on the effects of density changes or formulation changes on detonation rate, detonation pressure, explosion pressure, heat of explosion and numerous other properties, and have aided in evaluating the theoretical potential of explosives. In addition, a multitude of laboratory tests have been utilized for the evaluation of explosives. When comparing the computer data and the voluminous test data it became evident that numerous anomalies existed. Tests in rock were required to study explosives under borehole confinement. This fact was further emphasized after numerous field measurements showed that the borehole velocity of commercial explosives did not match the theoretical value but was dependent on conditions of field use. Since we are interested in the practical aspects of blasting, a program was initiated to evaluate explosives as used in commercial blasting. INSTRUMENTATION Most of you are familiar with the extensive work that has been done by the U. S. Bureau of Mines in their studies of strain measurements in rock. Early in our work we adopted procedures similar to those used by the Bureau of Mines. Strain pulses were measured by gages cemented in boreholes. Since we were primarily interested in the effect of explosives in the zone where fracture might occur, this system offered several disadvantages for Du Pont: 1. Cemented gages were expensive and not reusable. 2. When gage holes were used for several shots, there was considerable question as to the condition of the rock after the first shot.

Jan 1, 1968

By R. G. Stickney

INTRODUCTION The Basalt Waste Isolation Project, conducted by Rockwell Hanford Operations under contract to the U.S. Department of Energy, is assessing the feasibility of the disposal of commercial radioactive spent fuel/high-level waste in deep geologic formations in basalts beneath and within the Hanford Site in southeastern Washington State. The Basalt Waste Isolation Project mission is to identify and characterize a potential geologic repository site in basalt and to develop associated facilities and technology required for the potential permanent isolation of radioactive wastes in basalt formations. In support of the Basalt Waste Isolation Project, a laboratory testing program was conducted to evaluate the performance of the Council for Scientific and Industrial Research's "Doorstopper" biaxial strain cell. To support site characterization studies and the design of repository openings, in situ stress measurements will be conducted within the reference repository horizon (~970 m). The Doorstopper is one of the instruments being considered for use in these measurements. It was selected because it requires only a small volume of work to achieve stress relief, which is important in a closely jointed basalt. Also, test durations are short, permitting a large number of measurements to be made within a given time to increase confidence in the results. Within the reference repository horizon, temperatures are expected in the range of 40º to 60°C with a humidity of up to 100%. For this testing program, test conditions were selected to closely resemble those expected within the repository horizon. The Doorstopper test, mainly developed by Leeman (1964), is a strain rosette relief method of measuring rock stress in situ. The Doorstopper consists of a four element, 45º strain gage rosette

Jan 1, 1984

By J. E. Willson, N. K. Bohidar

An evaluation of internal stress distribution based on photoelastic studies and destructive testing of simulation models shows that pillar failure is a function of the internal stress distribution, and that stability can be changed by altering the internal stress pattern. Induced stresses in three-dimensional epoxy disks subjected to uniaxial forces were evaluated by photoelastic studies. Stress profiles across different sections perpendicular to the loading direction revealed two maxima for each profile. Based on the stress distribution for the entire column, an attempt was made to explain pillar spalling and the hour glass pattern of failure in a mine pillar. For maximum stability and optimum design of mine pillars, it is necessary to consider the external forces, the nature and distribution of induced stresses and the characteristics of the pillar material as determined in the laboratory. This paper summarizes the research done by N. K. Bohidarl and Ben L. seegrniller2 as partial fulfilment of the requirement for Master of Science degree in Mining Engineering, University of Utah. It is an evaluation of a study to determine the stress distribution in short columns in order that regions of high stress concentration in mine pillars may be found and their effect on pillar failure be ascertained. The ratios of the dimensions of the columns studied are representative of those found in mines located in flat-bedded deposits. The weight of the overburden generally constitutes the major external force. This force is calculated by taking into account specific weight and thickness of the cover. Determination of the distribution of this force on pillars may often require a complex analytical study. There have been many investigations of the strength

Jan 1, 1968

By Frederick Laist

IT IS obviously impossible to design a copper smelting plant which could be considered, ideal under all conditions. For example, a plant properly designed to smelt the concentrates resulting from the treatment of porphyry ores by flotation would not be the kind of plant that one would design for the treatment of a coarse pyritous copper ore. The smelting of flotation or other fine concentrates is generally accomplished in a reverberatory plant, although occasionally the concentrates are sintered and then smelted in blast furnaces. On the other hand, coarse self-fluxing ores, whether pyritic or semi-pyritic, are generally smelted in a blast-furnace plant. Even this statement is only- approximately true, since the choice will be influenced by many factors; for example, the kind of fuel available (coal, oil or coke), the value of power (electric or steam), the uses to which waste steam may be put (heating, drying, etc.), the cost of refractories (silica and fire brick), the permanence and continuity of the ore supply and the relative first costs of the two types of plant (the reverberatory plant is generally more expensive to construct and to shut down), the contour of the site on which the plant is to be built (rugged, rolling or flat), the intelligence and character of the labor avail-able, and many other factors. From these remarks, it is evident that no copper smelter can be ideal for all conditions of ore and locality, and inasmuch as most of the copper now being pro-duced comes from fine or flotation concentrates and these are generally smelted in reverberatory furnaces, I shall confine my remarks to this type of smelt-ing plant.

Jan 5, 1923

[ ] Granville S. Borden (Mining Taxation, P. 1049) has written two other published articles on the subject, Taxation and Mineral Resources, and An Income Tax Program for Mineral Producers. Both articles appeared in Mining Engineering. He is presently employed by Standard Oil Co. of California as a special tax counsel. He holds an LL. B and an LL. M from George Washington University and a Bachelor of Science in Mining from the University of California. He has been chairman of the Taxation Committee of the Minerals Economics div. of the AIME. Borden fishes, plays golf, prospects, and performs mineral analysis as hobbies. [ ] Charles C. Towle (co-author, Uranium Deposits of the Grants District, New Mexico, P. 1037) graduated from the Colorado School of Mines with a degree in Geological Engineering. He was a member of Sigma Nu; Theta Tau, an honorary professional society; Blue Key, honorary social society; the glee club and quartet, and a member of the student council. He has been a mucker, driller, flotation operator and mill shift boss for the Clear Creek-Gilpin Co., Idaho Springs, Colo.; Geologist, chief engineer, and chief geologist for Patino Mines & Enterprises Consolidated, Inc., Bolivia; appraisal engineer and part-time geology student, Denver; office geologist for Geology Dept., special Engineering div., Sea Level Canal Studies, Panama Canal; and geologist, div. of Raw Materials, USAEC, Grand Junction, Colo. He is currently chief of the Denver Exploration Branch, div. of Raw Materials, USAEC, Denver. Towle was at one time a tournament golfer, playing three and four times a week. While working in South America he played in numerous tournaments. Today, although playing only occa sionally, he shoots in the low eighties.

Jan 1, 1952

By L. C. McCabe

THE object of the present investigation was to discover a physical basis for rank differentiation of coals, particularly the coals of the Illinois basin. Vitrain1 was selected as the most appropriate coal material to use in the investigation, because of its homogeneity and ease of acquisition and handling. Previous Investigations.-Hoffman and Jenker2 have shown that their index of reflection is a characteristic of coal rank and that the Leitz slit microphotometer may he used in determining the different intensities of reflection. Zhemchuzhnikov3 measured the luster of several Russian coals with a color analyzer and found that the degree of luster was indic-ative of rank. Luster-volatile matter curves based on data from Sucan and Donetz coals were satisfactorily used for determining the rank or volatile content of other coals after the luster strength was determined. In 1934 Fisher4 reported refractive indices of 1.76 for bituminous vitrain and 1.87 for semibituminous vitrain. Investigation of Angle of Polarization.-Early in the present investiga-tion several determinations of the refractive indices of the vitrains were made by immersing the minus 150 plus 200-mesh powder in oils. It was found that all the samples fell within the range 1.6 to 1.8. However, difficulty was encountered in securing oils in this high index range that were closely enough spaced to separate some of the coals. The writers made a number of determinations of the angle of maxi-mum polarization from the polished surfaces of the vitrains and derived their refractive indices by the procedure described in the follow-ing paragraphs.

Jan 1, 1937

By Arthur S. Coffinberry, Ralph Hultgren

WE have studied the gold-aluminum system by X-ray diffraction and by the microscope over the entire range of composition for temperatures between 300° and 500° C. Results obtained are shown in Fig. 1, combined with the work of Heycock and Neville1 at higher temperatures. The diagram differs in important details from that given by Hansen2 in his critical compilation of the literature of binary alloy systems. This work was undertaken both because of the intrinsic value of a knowledge of the phase diagram of this system and because of the need of theoretical metallurgy for precise and accurate data, particularly X-ray diffraction data. Systematic studies of equilibrium diagrams, particularly by Hume-Rothery,3 have shown regularities that yield a certain insight into the nature of alloying forces. It has been shown, for example, that solid solubility depends on the concentration of free electrons in the alloy, on the relative radii of solvent and solute atoms, on the forces of attraction between atoms, and on the relative stability of intermediate phases. The well-known Hume-Rothery rule states that the crystal structures and compositions of many intermediate phases depend on the electronto-atom ratio. This has been confirmed and extended by wave mechanical calculations.4 A knowledge of the forces between atoms in alloys, even an imperfectly developed empirical one, should be a valuable guide in the preparation of technological alloys of desirable properties. Furthermore, such information is basic in such problems as rate of diffusion, age-hardening, phase transformations, and others. The most valuable data for this purpose are furnished by X-ray diffraction studies. Unfortunately, work has been

Jan 1, 1938

By K. Kim

INTRODUCTION A thorough evaluation of the geologic material being considered must be conducted to determine the feasibility of constructing a large-scale underground facility in a deep geologic formation. The design and construction of a nuclear waste repository in basalt, due to the unprecedented nature of the project, adds significantly to the need for thoroughness of this evaluation and mandates that geoengineering data and analysis be of the highest quality. The investigations required to collect the data encompass in situ measurements and observations, as well as laboratory and field tests. Mathematical (numerical) models, which are required to predict the long-term performance of the repository structure, must be developed to evaluate rock mass behavior at canister, room, and repository scale and eventual 1 y must be validated through in situ tests and monitoring. The information generated from these geo- mechanics investigations is essential for assessing site suitability and will be utilized in the development of the repository design, the engineered barrier design, and the evaluation of repository performance. The Hanford Site near Richland, Washington is one of nine sites throughout the nation being investigated by the U .S. Department of Energy as a possible location for the first high-level nuclear waste repository in deep geologic formations. The process of site characterization is currently in progress. If the site is nominated by the U.S. Department of Energy, an extensive program will be undertaken, the culmination of which will be a decision on the suitability of the site for waste disposal. There are a mu1titude of elements to the proposed site characterization

Jan 1, 1984

By Ralph H. Kress

Haulage trucks designed expressly for mine service were introduced about 35 years ago. The first models to arrive on the scene hauled about 15 tons and easily outperformed the modified highway trucks that had been used for mine haulage up to that time. The specialized trucks obviously had a greater potential for mining operations, and once this fact was recognized, competitive pressures in both the mining and truck-manufacturing industries drove the new vehicles toward ever more efficient performance. Many changes in truck design resulted, but not all were accepted for a variety of reasons. Often poor design was the reason, but in many cases progressive and promising designs were abandoned only because the truck manufacturer lacked the courage, tenacity, or vision to capitalize on them. There were also many cases where a promising new design was abandoned because the prototypes were initiated in a mine where personnel lacked the patience to prove them. Truck Startup Takes A Team Ally new truck that is to succeed and contribute to lower mine haulage costs must be well conceived and launched with good teamwork on the part of all concerned. Naturally, it is essential to have a good overall truck design at the outset to make this teamwork worthwhile. The design must include the selection of the right components manufactured by suppliers that can each do justice to their particular part of the new truck. Last, but by no means least, the mine operator where the truck is to be launched must be enthusiastic in his efforts to see the new vehicle through to successful operation.

Jan 1, 1971

By John W. Padan, Thomas E. Howard

Most of what has been written during the past few years on marine mineral resources has emphasized the vast potential of the ocean, and its floor, as a source of the vital mineral raw materials upon which our modern technological society depends. Computations have been made to demonstrate that the sea contains sufficient minerals to support any reasonable world population indefinitely. The importance of these resources from the standpoint of strengthening the national mineral resource base has been pointed out. And though the information upon which these conclusions are based is sketchy, essentially qualitative, and often conflicting, there can be no doubt that the mineral potential of the sea is tremendous and that there are compelling reasons for working toward its exploitation. Unfortunately, there has been little emphasis on the problems that must be overcome, from the perspective of the economics of mineral production. Some of these problems have been noted, and some authors have appraised them realistically. However, many proposed solutions have been more romantic than practical, from the standpoint of both technology and economics. As a result the general impression has been given, particularly to those uninitiated in the realities of mineral production, that the mineral wealth of the sea is there for the taking-requiring only a good modicum of courage and technologic innovation to place it within easy grasp. But developing the capability necessary for substantial, profitable production of sea bottom minerals will be far from easy. It will be accomplished much more quickly if the problems are faced squarely, defined properly, and attacked in an orderly, logical sequence. While this approach may lack glamour, it offers the highest probability for success.

Jan 6, 1966

By Marius R. Campbell

Does mine-sampling show the commercial value of a coal, and if so, how should it be done ? This question is often asked, but seldom answered. During the past summer, while engaged in securing coal for the Government coal-testing plant at St. Louis, I had an excellent opportunity to obtain information on t,his subject, and the results seem to furniih an answer to the question propounded above. Sampling for the U. 8. Geological Survey Coal- Testing Plant. In organizing the work of the testing-plant, it was decided that coal, in car-load lots only, would be accepted for testing; also that this coal should be loaded under the immediate supervision of a representative of the plant, so as to be certain that the car-load sample would be representative. As an additional check on the work, two mine-samples were to be collected from each mine visited, and these samples, as well as the sample from the car when it was received at the testing-plant, were to be carefully analyzed at the chemical laboratory established in connection with the plant and operated under the direction of Prof. N W. Lord of the Ohio State University, Columbus, Ohio. Mine-Samp1ing.—Mine-samples were collected with great care by me and my assistants, Messrs. J. Shober Burrows, John W. Groves and Frank W. De Wolf. The dominant idea in the regulations adopted for mine-sampling mas, that it should be done in such a manner that the sample would have the same composition as the commercial output of the mine.

Jan 1, 1906

By Joseph Hodgson

IN 1880, mining operations were commenced at the Copper Queen mine. The famous Queen orebody, which extended to the surface, was first quarried from a large open cut in the outcrop. The orebody was followed down to the 300 level with the Queen incline, and stoped. This, we believe, marks the introduction of square setting in the Bisbee district, which is still the method most generally used. Orebodies The orebodies in the Copper Queen mine occur in the limestones, and the main portion of the ore has been mined from the Abrigo, Martin, and. Escabrosa limestones. While the orebodies outcrop in the extreme western end of the mine, the general dip is to the east and south, at an angle of about 20°, although this dip is not by any means regular, being, in fact, very irregular locally. The ore is remarkable for its variableness in character, some of it being very soft, requiring a large amount of timber, and other portions consisting of extremely hard sulphides. The orebodies, in general, While remarkable for their continuity, are very irregular, both as to shape and size. The mine having been in operation so many years, and mining having been prosecuted over such a large area, the operations have caused the shrinkage of the overburden, and there is a constant movement, which is shown y large cracks and interstices in the surface rocks, which largely contribute to the very high deadwork or maintenance cost of the mine. It is surprising that for year 1913 it cost almost $400,000 just for the one item of repairs and deadwork in this property.

Jan 8, 1914

By Arthur Coffinberry

EVE have studied the gold-aluminum system by X-ray diffraction and by the microscope over the entire range of composition for temperatures between 300° and 500° C. Results obtained are shown in Fig. 1, com-bined with the work of Heycock and Neville1 at higher temperatures. The diagram differs in important details from that given by Hansen2 in his critical compilation of the literature of binary alloy systems. This work was, undertaken both because of the intrinsic value of a knowledge of the phase diagram of this system and because of the need of theoretical metallurgy for precise and accurate data, particularly X-ray diffraction data. Systematic studies of equilibrium diagrams, particularly by Hume-Rothery,3 have shown regularities that yield a certain insight into the nature of alloying forces. It has been shown, for example, that solid solubility depends on the concentration of free electrons in the alloy, on the relative radii of solvent and solute atones, on the forces of attraction between atoms, and on the relative stability of intermediate phases. The well-known Hume-Rothery rule states that the crystal structures and compositions of many intermediate phases depend on the electron-to-atom ratio. This has been confirmed and extended by wave mechanical calculations.4 A knowledge of the forces between atoms in alloys, even an imperfectly developed empirical one, should be a valuable guide in the preparation of technological alloys of desirable properties. Furthermore, such informa-tion is basic in such problems as rate of diffusion, age-hardening, phase transformations, and others. The most valuable data for this purpose are furnished by X-ray diffraction studies. Unfortunately, work has been

Jan 1, 1938

By C. R. McClure

The objective of this papef is to summarize briefly the practical use of rock mechanics in design and construction of various types of structures. These range from foundation for industrial facilities, nuclear power plants, bridges and dams to tunnels and underground caverns. The use of rock mechanics has varied from performing a few laboratory unconfined compressive tests on core samples to complete field and laboratory tests for underground power caverns. The primary difference between the rock mechanics studies we hare for construction projects and those most commonly found in the literature is that our tests must provide immediate answers to specific questions facing a design or construction engineer. For example, when we make a plate-bearing test we arrive at a load-deformation relationship. We realize that this is not a true modulus of elasticity. Yet, when considering the resistance the rock will provide against forces occurring in a pressure tunnel it is a far more useful value than the true modulus of elasticity of the rock. Another example of this difference in interest is in the use of flat jacks. Many people criticize the use of flat jacks because they measure the stresses in the disturbed zone very near the surface and do not represent the undisturbed stress condition in the rock. However, in actual construction it is frequently those near-surface stresses with which we must cope. We are interested in both the stress conditions present prior to excavation and those as modified by construction of an exploratory adit or drift. Fundamentally, we are interested in the practical application of rock mechanics in the solution of problems of design and construction of civil engineering works.

Jan 1, 1968

By Dr. O’Neil Thomas J., Donald W. Gentry

It was a western truism that more money was made from selling mines than from buying them, just as it was accepted that many a good mine had been spoiled by working it. from R. E. White, "The Mining Town," Alta California August 18,1873 INTRODUCTION One of the most important aspects of mineral enterprises of US corporations is the influence of the depletion allowance on cash flow. This allowance permits mineral producers to claim sizable federal income tax deductions not available to other industries, and these deductions significantly increase cash flows in mining. In the past several years the minerals depletion allowance has come under increasingly heavy fire from many sectors as a tax loophole that deprives the federal government of large amounts of revenue. One estimate of the loss of tax dollars in 1968 was $2.25 billion due to depletion deductions and intangible expenses in the oil industry. Largely on the basis of such arguments, the Tax Reform Act of 1969 reduced percentage depletion rates for a number of minerals, and the Tax Reduction Act of 1975 totally eliminated statutory depletion for most oil and gas. In regard to percentage depletion for hard minerals, the federal government has estimated its resulting loss of revenue at $1.75 billion for 1980. The TEFRA legislation of 1982 further reduced the statutory depletion allowance available to iron ore, coal, and lignite beginning in 1984. Thus, it is clear that minerals engineers and managers should have a thorough knowledge of the origin, evolution, justification, and computational procedures relating to the depletion allowance. ORIGIN AND EVOLUTION OF THE DEPLETION ALLOWANCE

Jan 1, 1984

By Arthur S. Coffinberry, Ralph Hultgren

We have studied the gold-aluminum system by X-ray diffraction and by the microscope over the entire range of composition for temperatures between 300° and 500° C. Results obtained are shown in Fig. 1, combined with the work of Heycock and Neville1 at higher temperatures. The diagram differs in important details from that given by Hansen2 in his critical compilation of the literature of binary alloy systems. This work was undertaken both because of the intrinsic value of a knowledge of the phase diagram of this system and because of the need of theoretical metallurgy for precise and accurate data, particularly X-ray diffraction data. Systematic studies of equilibrium diagrams, particularly by Hume-Rothery,3 have shown regularities that yield a certain insight into the nature of alloying forces. It has been shown, for example, that solid solubility depends on the concentration of free electrons in the alloy, on the relative radii of solvent and solute atoms, on the forces of attraction between atoms, and on the relative stability of intermediate phases. The well-known Hume-Rothery rule states that the crystal structures and compositions of many intermediate phases depend on the electron-to-atom ratio. This has been confirmed and extended by wave mechanical calculations.4 A knowledge of the forces between atoms in alloys, even an imperfectly developed empirical one, should be a valuable guide in the preparation of technological alloys of desirable properties. Furthermore, such information is basic in such problems as rate of diffusion, age-hardening, phase transformations, and others. The most valuable data for this purpose are furnished by X-ray diffraction studies. Unfortunately, work has been

Jan 1, 1938

By Fred D. DeVaney and

The coercimeter, as its name implies, is an instrument for measuring the coercive forcet of magnetic substances. It was developed by Davis and Hartenheim in the Special Studies Section, Metallurgical Division. A detailed description of this apparatus may be found elsewhere.2 The coercive force determinations of magnetic materials are interesting because of the relationship established by Gottschalk,4 who showed a linear relationship between the magnetization coercive force and the specific surface of comminuted particles. The value of this relationship in determining grinding efficiency has been shown by Dean.3 The determination of the surface contained in the subsieve sizes has always been a difficult problem for investigators. They made approximate measurements of the surface of coarse materials by sizing on screens, but for the determination of the surface of the sub-sieve sizes it was necessary to make detailed grain counts or elutriation tests, or to study dissolution rates. The technical literature contains many references to other methods for determining these surfaces, either by some special apparatus or by mathematical calculations based on distribution lines. Many of the methods are long and tedious, and the results of some, at least, are questionable. he turbidimeter gives quick results on ground cement. By using magnetite as the material to be ground, a simple determination of its coercive force by the coercimeter, requiring 10 minutes or less, can be transposed directly and accurately into units of relative surface. This subject has been pursued further by the U. S. Bureau of Mines in cooperation with the Missouri School of Mines and Metallurgy, Rolla, Mo., and the following is a description of the results.

Jan 1, 1939

By Shiou-Chuan Sun

THE effects of oxidation on the flotation behavior of sulphide minerals have been extensively studied 1-3 but no similar study has been made of coals. Coals of bituminous and lower rank undergo atmospheric oxidation during mining and storage, and their degree of oxidizing increases with temperature, 4,5 and time of exposure." The problem of recovering fine oxidized coal from culm piles, rivers, and streams by froth flotation has become increasingly important to the coal industry as well as to those concerned with air and stream pollution. This paper describes the flotation behavior of oxidized and unoxidized coals and carbons in the presence of oily collectors and presents the reagents found effective in the flotation of oxidized coals and carbons. Except where otherwise stated, flotation tests were performed in a 50-g Denver flotation cell. Solid feed for each test was 30 g, and the pulp dilution was kept at 8.5. The —65 mesh coal sample was wetted by agitation with water in the flotation cell for 6 min, then conditioned with a predetermined amount of collector for 2 min, and finally floated with pine oil as frother for 3 min. The oxidation of coals and carbons was performed in a vertical, electrically heated glass tube, shown in Fig. 1. One hundred grams of —65 mesh coal were fed into the glass tube and heated to 10° to 20 °C below the predetermined temperature of oxidation. Compressed air was admitted to the tube at a rate of 0.05 cu ft per min and the temperature was controlled by a variable voltage regulator. The oxi-

Jan 1, 1955

By Fred D. DeVaney and

The coercimeter, as its name implies, is an instrument for measuring the coercive forcet of magnetic substances. It was developed by Davis and Hartenheim in the Special Studies Section, Metallurgical Division. A detailed description of this apparatus may be found elsewhere.2 The coercive force determinations of magnetic materials are interesting because of the relationship established by Gottschalk,4 who showed a linear relationship between the magnetization coercive force and the specific surface of comminuted particles. The value of this relationship in determining grinding efficiency has been shown by Dean.3 The determination of the surface contained in the subsieve sizes has always been a difficult problem for investigators. They made approximate measurements of the surface of coarse materials by sizing on screens, but for the determination of the surface of the sub-sieve sizes it was necessary to make detailed grain counts or elutriation tests, or to study dissolution rates. The technical literature contains many references to other methods for determining these surfaces, either by some special apparatus or by mathematical calculations based on distribution lines. Many of the methods are long and tedious, and the results of some, at least, are questionable. he turbidimeter gives quick results on ground cement. By using magnetite as the material to be ground, a simple determination of its coercive force by the coercimeter, requiring 10 minutes or less, can be transposed directly and accurately into units of relative surface. This subject has been pursued further by the U. S. Bureau of Mines in cooperation with the Missouri School of Mines and Metallurgy, Rolla, Mo., and the following is a description of the results.

Jan 1, 1939